LG Electronics ru-44sz80l User Manual

LCD Projection TV
OWNER’S MANUAL
Please read this manual carefully before operating your set. Retain it for future reference. Record model number and serial number of the set. See the label attached on the back cover and quote this information to your dealer when you require service.
LG Electronics U.S.A., Inc.
PAGE 2
WARNING:
TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
POWER CORD POLARIZATION:
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.
NOTE TO CABLE/TV INSTALLER:
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical.
REGULATORY INFORMATION:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equip­ment is operated in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio com­munications. However, there is no guarantee that interference will not occur in a particular installation. If this equip­ment does cause harmful interference to radio or television reception, which can be determined by turning the equip­ment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
CAUTION:
Do not attempt to modify this product in any way without written authorization from LG Electronics Corporation. Unauthorized modification could void the user’s authority to operate this product.
COMPLIANCE:
The responsible party for this product’s compliance is: LG Electronics U.S.A., Inc 1000 Sylvan Avenue, Englewood Cliffs, NJ 07632 1-201-816-2000 http://www.lgusa.com
WARNING
RISK OF ELECTRIC SHOCK DO NOT OPEN
PAGE 3
Important safeguards for you and your new product
Your product has been manufactured and tested with your safety in mind. However, improper use can result in electrical shock or fire hazards. To avoid defeating the safeguards that have been built into your new product, please read and observe the following safety points when installing and using your new product, and save them for future reference.
Observing the simple precautions discussed in this manual can help you get many years of enjoyment and safe operation that are built into your new product.
This product complies with all applicable U.S. Federal safety requirements, and those of the Canadian Standards Association.
(Continued on next page)
1. Read Instructions
All the safety and operating instructions should be read before the product is operated.
2. Follow Instructions
All operating and use instructions should be followed.
3. Retain Instructions
The safety and operating instructions should be retained for future reference.
4. Heed Warnings
All warnings on the product and in the operating instruc­tions should be adhered to.
5. Cleaning
Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
6. Water and Moisture
Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool.
7. Accessories, Carts, and Stands
Do not place this product on a slippery or tilted surface, or on an unstable cart, stand, tripod, bracket, or table. The product may slide or fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recom­mended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufac­turer’s instructions, and should use a mounting accessory recommended by the manufacturer.
8. Transporting Product
A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn.
9. Attachments
Do not use attachments not recommended by the product manufacturer as they may cause hazards.
10. Ventilation
Slots and openings in the cabinet are provided for ventila­tion and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.
11. Power Sources
This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, con­sult your product dealer or local power company. For prod­ucts intended to operate from battery power, or other sources, refer to the operating instructions.
12. Power-Cord Polarization
This product is equipped with a polarized alternating-cur­rent line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety pur­pose of the polarized plug.
13. Power-Cord Protection
Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.
IMPORTANT SAFETY INSTRUCTIONS
PORTABLE CART WARNING
PAGE 4
(Continued from previous page)
14. Outdoor Antenna Grounding
If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded to provide protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code (U.S.A.), ANSI/ NFPA 70 provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna­discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.
15. Lightning
For added protection for this product (receiver) during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges.
16. Power Lines
An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.
17. Overloading
Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock.
18. Object and Liquid Entry
Never push objects of any kind into this product through
openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.
19. Servicing
Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
20. Damage Requiring Service
Unplug this product from the wall outlet and refer servic­ing to qualified service personnel under the following con­ditions:
a. If the power-supply cord or plug is damaged. b. If liquid has been spilled, or objects have fallen into
the product.
c. If the product has been exposed to rain or water.
d. If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation.
e. If the product has been dropped or the cabinet has been damaged.
f. If the product exhibits a distinct change in perfor­mance.
21. Replacement Parts
When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the origi­nal part. Unauthorized substitutions may result in fire, electric shock, or other hazards.
22. Safety Check
Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condi­tion.
23. Wall or Ceiling Mounting
The product should be mounted to a wall or ceiling only as recommended by the manufacturer. The product may slide or fall, causing serious injury to a child or adult, and seri­ous damage to the product.
24. Heat
The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.
Antenna Lead in Wire
Antenna Discharge Unit (NEC Section 810-20)
Grounding Conductor (NEC Section 810-21)
Ground Clamps
Power Service Grounding Electrode System (NEC Art 250, Part H)
Ground Clamp
Electric Service
Equipment
Example of Grounding According to National Electrical Code Instructions
Fig. 1
NEC - National Electrical Code
IMPORTANT SAFETY INSTRUCTIONS
PAGE 5
Table of Contents
Setup Checklist
Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Important Safety Instructions . . . . . . . . . . . . . . . . .3-4
Function Status Indicators . . . . . . . . . . . . . . . . . . . . .6
Step 1. Hook Up TV
Rear Connections Panel . . . . . . . . . . . . . . . . . . . . . . .7
Side Connections Panel . . . . . . . . . . . . . . . . . . . . . . .8
ANT/Cable Service Hookup . . . . . . . . . . . . . . . . . . . . .9
Cable Box Connections . . . . . . . . . . . . . . . . . . . . . . .10
VCR Connections . . . . . . . . . . . . . . . . . . . . . . . . . . .11
DVD Player . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
RGB-DTV/DVI-DTV Input . . . . . . . . . . . . . . . . . . . . . .13
RGB-PC/DVI-PC Input . . . . . . . . . . . . . . . . . . . . . . .14
External Stereo Connections . . . . . . . . . . . . . . . . . . .15
Home Theater: Speaker Layout . . . . . . . . . . . . . . . . .16
Monitor Out Setup . . . . . . . . . . . . . . . . . . . . . . . . .17
Remote Control Functions In TV Mode . . . . . . . . . . .18-19
On-Screen Displays . . . . . . . . . . . . . . . . . . . . . . . . .20
Front Panel Controls . . . . . . . . . . . . . . . . . . . . . . . .21
Step 2. Customize your TV’s Features
SETUP Menu Options
EZ Scan (Channel Search) . . . . . . . . . . . . . . . . . . . .22
Channel Add/Delete/Surf Setup . . . . . . . . . . . . . . . .23
Channel Labels Setup . . . . . . . . . . . . . . . . . . . . . . .24
Main Picture Source Selection . . . . . . . . . . . . . . . . . 25
PIP (Picture-in-Picture) / Twin Picture Operation . . . . . .26
POP (Picture-outside-Picture) . . . . . . . . . . . . . . . . .27
Booster . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
VIDEO Menu Options . . . . . . . . . . . . . . . . . . . . .29-30
AUDIO Menu Options . . . . . . . . . . . . . . . . . . . . .31-32
TIME Menu Options
Auto Clock Setup . . . . . . . . . . . . . . . . . . . . . . . . .33
Manual Clock Setup . . . . . . . . . . . . . . . . . . . . . . . .34
TV Turn Off Time Setup . . . . . . . . . . . . . . . . . . . . .35
TV Turn On Time Setup . . . . . . . . . . . . . . . . . . . . . .36
Sleep Timer Setup . . . . . . . . . . . . . . . . . . . . . . . . .37
Auto Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
SPECIAL Menu Options
Aspect Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
On-Screen Menu Languages . . . . . . . . . . . . . . . . . . 40
Captions Setup . . . . . . . . . . . . . . . . . . . . . . . . . . .41
Caption/Text Mode Selection . . . . . . . . . . . . . . . . . .42
Key Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Cinema Mode Setup . . . . . . . . . . . . . . . . . . . . . . . .44
Demo (Menu Review) . . . . . . . . . . . . . . . . . . . . . . .45
LOCK Menu Options
Parental Lock Setup . . . . . . . . . . . . . . . . . . . . . . . .46
Parental Lock (Ratings Overview) . . . . . . . . . . . . . . .47
Step 3. Miscellaneous
Programming the Remote . . . . . . . . . . . . . . . . . . . . .48
Programming Codes . . . . . . . . . . . . . . . . . . . . . .49-52
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . .54-55
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56-57
Product Specifications . . . . . . . . . . . . . . . . . . . . . .58
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59-60
Step 1. Make all equipment and source connections. See pages 10-17.
Step 2. Install batteries in remote control and do a channel search. See page 22.
Step 3. Adjust TV features and options to your preference. See contents above.
Note: Design and specifications are subject to change without prior notice.
PAGE 6
Function Status Indicators
Lamp indicator, operation indicator, and temperature indicator located below the front panel controls,
reveal the operating status of the LCD projection TV.
Operation Indicator
Lamp Indicator
Temperature Indicator
Off Power cord is not connected. Red Power Cord is connected, TV is in standby mode. Green TV turns on. Orange (flashing) Preparing operation in standby mode. Orange Projection lamp is reaching the end of its life and needs to
be replaced with a new lamp.
Red (flashing) There is a problem with the lamp or around it. Contact an
authorized service center. Green (flashing) The lamp cover is not closed. Orange The projection TV is overheating. Red The projection TV shut down due to overheating. Red (flashing) The projection TV shut down, check the cooling fan.
Operation Indicator
Lamp Indicator
Temperature Indicator
AUDIO
CENTER
MODE IN
P
R
DVI INPUT
DTV/DVD
(480i/480p/720p/1080i)
COMPONENT
INPUT2 INPUT1
PB
Y
PC/DTV (XGA/ 480p/ 720p/ 1080i)
PC/DTV (XGA/ 480p/ 720p/ 1080i)
RGB INPUT
UPGRADE PORT
RGB/DVI INPUT
(R)
(L)
AUDIO
(R)
(L)
AUDIO
(R)
(L)
AUDIO
VARIABLE
AUDIO OUT
MONITOR
OUT
VIDEO
INPUT 2
VIDEO
INPUT 1
S-VIDEO
(R)
(L)
AUDIO
VIDEO
MONO
+75
ANT IN
PAGE 7
Mini glossary
JACK A connection on the back of a TV, VCR, or any other A/V device. This includes the RF jack and the Audio/Video jacks that are color-
coded.
SIGNAL Picture and sound traveling through cable, or over the air, to your television screen.
Rear Connections Panel
S-VIDEO In
A connection available with some high-end equipment that provides even better picture quality for Video 2.
Variable Audio Out
Used to connect either an external amplifier, or add a sub-woofer to your surround sound system.
RF Connector: Antenna
Used to connect analog cable or antenna signals to the television, either directly or through your cable box.
Video 1 or 2
Connects the video sig­nals from various types of equipment.
Component Input 1-2
Connect a component video/audio device
to these jacks. Refer to your DVD manual
for further information.
Connecting cables and external equipment to your TV.
Monitor Out
Connects to a second TV or Monitor.
Left/Right Audio
Used for stereo sound from various types of equipment.
RGB/DVI Input
Connect the TV output con-
nector from a PC/DTV to the
appropriate input port.
RGB/DVI Input
Used for audio connections
from a PC source or HD-STB
Satellite system.
Audio Center Mode In
Connect to external Dolby Digital Center preamp out­put.
Fan Cover
Replace or clean the filter to prevent a dust every 1~3 months. When cleaning or replacing the filter, certainly turn the main switch off. The dust filter must be washed in tepid water with netural detergent.
PAGE 8
Side Connection Panel
Side A/V Panel
S-VIDEO
VIDEO
SIDE VIDEO
AUDIO
(
R
)
(
L
)/
M
O
N
O
There are four jacks on the left side on your projection TV that make connecting Audio/Video devices like video games and cam­corders very simple.
The jacks are like those found on the back jack connection panel. This means that most equipment that connects to those types of jacks on the rear jackpack, may be connected to the side connec­tion panel.
To use the side jacks as the signal source, select them using Main Input menu as described on page 25. They will be named “Side Video in the Main Input menu.
Left/Right Audio
Used for stereo sound
from various types of
equipment.
Video
Connects the video
signals from any
piece of equipment.
S-Video
A connection available on some very high-end equipment that provides better picture quality than video input.
If you input both Side Video and S­Video, only the S-Video will work.
If you’re connecting a video game device, make sure to change the picture settings with the EZ Picture option in the Video menu (see page
29).
Mini glossary
A/V CABLES Audio/Video cables. Three cable connectorRight audio (red), Left audio (white), and Video (yellow). A/V cables are used for stereo
playback of videocassettes and for higher quality picture and sound from other A/V devices.
A/V DEVICE Any device that produces video or sound (VCR, DVD, cable box, or television).
PAGE 9
ANT / Cable Service Hookup
1
Connect an antenna or cable service to your TV as shown.
Turn to page 22 to do a channel search with EZ Scan for Ant/Cable connection(s).
For best signal reception, it is recommended to have your Antenna professionally adjusted.
2
If you receive your RF signal through an antenna that is several years old and connects with two small prongs, you will need to pur­chase a 300 to 75 ohm adapter. It should be available from your local electronics dealer.
We recommend using a 75 ohm cable for your antenna connections in order to prevent interference.
MONITOR
OUT
VIDEO
INPUT 2
VIDEO
INPUT 1
S-VIDEO
(R)
(L)
AUDIO
VIDEO
MONO
+75
ANT IN
Antenna
Cable TV Wall Jack Panel
RF Coaxial Wire (75 ohm)
RF Coaxial Wire (75 ohm)
PAGE 10
Cable Box Connections
Locate the output jack on the back of your cable box. Connect this to the Antenna jack on the back of your TV.
Or find the composite video and audio jacks on the back of your cable box, and connect them following the instructions provided with your equipment. This can be combined with any other equipment you may want to hook up.
1
In
Output Switch
Out
3 4
Audio
TV
VCR
L
R
Video
MONITOR
OUT
VIDEO
INPUT 2
VIDEO
INPUT 1
S-VIDEO
(R)
(L)
AUDIO
VIDEO
MONO
+75
ANT IN
Cable TV Wall Jack Panel
RF Coaxial Wire (75 ohm)
Cable Box
If you’re using a cable box, leave the TV on channel 3 or 4 and use your cable box to change channels.
PAGE 11
1
VCR Connections
Locate the Antenna jack on the back of your TV. Connect this to RF out jack on the back of your VCR.
Or, find the composite video and audio jacks on the back of your VCR, and connect them following the instructions provided with your equipment.
You may connect either the com­posite video or the S-Video cables to your TV. (Do not connect both the composite and the S-Video cables. In the event that you con­nect both composite and the S­Video cables, only the S-Video will work.)
To hear stereo sound from cable or your VCR, you will need to connect A/V cables as well as the wire that runs from the VCR to your TV.
If you want to receive your signals on Channel 3 or 4, locate the Out to TV jack on your VCR. Connect a cable from the Out to TV jack to the Antenna In jack on the back of your TV.
After connecting external equipment to the TV, don’t display a still picture for a long time on the screen. Doing so may damage the TV screen.
In
Out
Audio
L
R
Video
3 4
S-Video
Output Switch
MONITOR
OUT
VIDEO
INPUT 2
VIDEO
INPUT 1
S-VIDEO
(R)
(L)
AUDIO
VIDEO
MONO
+75
ANT IN
Antenna
RF Coaxial Wire
(75 ohm)
Round Wire (75 ohm)
A/V cables not included with TV
VCR
Back AV Panel
Cable TV Wall Jack Panel
PAGE 12
DVD Player
Mini glossary
COMPONENT VIDEO Some video equipment uses three separate lines (Y, P
B, PR) to more precisely reproduce images. Your video equipment manual
will explain how this relates to your equipment.
Find the audio and component or S-Video jacks on the back of your DVD Player and connect them fol­lowing the instructions provided with your equipment.
You may connect either the com­posite video or the S-Video cables to your TV. Do not connect both the composite and the S-Video.
1
Component 1 (or 2) Input
Y PB PR
1920X1080i
1280X720p
720X480p
720X480i
Audio LR
Dolby Digital Out
Component Video
S-Video
AUDIO CENTER
MODE IN
P
R
DVI INPUT
DTV/DVD
(480i/480p/720p/1080i)
COMPONENT
INPUT2 INPUT1
PB
Y
PC/DTV (XGA/ 480p/ 720p/ 1080i)
PC/DTV (XGA/ 480p/ 720p/ 1080i)
RGB INPUT
UPGRADE PORT
RGB/DVI INPUT
(R)
(L)
AUDIO
(R)
(L)
AUDIO
(R)
(L)
AUDIO
VARIABLE
AUDIO OUT
MONITOR
OUT
VIDEO
INPUT 2
VIDEO
INPUT 1
S-VIDEO
(R)
(L)
AUDIO
VIDEO
MONO
Component input jacks
on the Monitor
Y
PB
PR
Video output jacks on DVD player
Y Y Y Y
Pb
B-Y
Cb PB
Pr
R-Y
Cr
P
R
Component Input ports
Connect DVD player jacks to Monitor Component input jacks as indicated below.
A/V Cables Not included with TV
DVD Player
Back AV Panel
Some high-end DVD players use a picture reproduction system called “component video.” If your DVD player has component output, use the connectors marked “Component 1/2” on the jack panel. Please refer to your DVD manual for proper installa­tion.
PAGE 13
RGB-DTV/DVI-DTV Input
Find the audio and Y, PB, PR/RGB/DVI jacks on the back of your DBS receiver and con­nect them following the instructions provid­ed with your equipment.
Connect these cables to your TV as shown.
1
2
The DTV shows the sharpest picture in 720p mode.
Select RGB-DTV Source and press ENTER. Use UP/DOWN arrows to select the desired options (H-Position/ V-Position/Phase) and then use LEFT/RIGHT arrows to make appropriate adjustments.
Audio
L R
Component Out
Y Pb Pr
Dolby Digital
Out
PR
DVI INPUT
DTV/DVD
(480i/480p/720p/1080i)
COMPONENT
INPUT2 INPUT1
PB
Y
PC/DTV (XGA/ 480p/ 720p/ 1080i)
UPGRADE PORT
(R)
(L)
AUDIO
Audio L R
Dolby Digital
Out
AUDIO CENTER
MODE IN
P
R
DVI INPUT
DTV/DVD
(480i/480p/720p/1080i)
COMPONENT
INPUT2 INPUT1
PB
Y
PC/DTV (XGA/ 480p/ 720p/ 1080i)
PC/DTV (XGA/ 480p/ 720p/ 1080i)
RGB INPUT
UPGRADE PORT
RGB/DVI INPUT
(R)
(L)
AUDIO
(R)
(L)
AUDIO
(R)
(L)
AUDIO
VARIABLE
AUDIO OUT
HD-SET TOP
1920x1080i
1280x720P
720x480P
RGB-DTV/DVI-DTV Input
Signal
480i 480p 720p
1080i
Component1
Yes Yes Yes Yes
Component2
Yes Yes Yes Yes
RGB/DVI-DTV
No Yes Yes Yes
This TV supports HDCP (High-bandwidth Digital Content Protection) protocol for DVI-DTV (480p, 720p, 1080i) mode.
DBS Receiver
DBS Receiver
A/V Cables Not included with TV
A/V Cables Not included with TV
In RGB-DTV mode, H-Position/ V-Position/Phase are not adjustable if you choose either the POP or Twin picture modes.
or
PAGE 14
RGB-PC/DVI-PC Input
Find the audio and RGB or DVI jacks on the back of your PC and then connect them fol­lowing the instructions provided with your equipment.
Connect these cables to your TV as shown.
1
2
Synchronization input form: Signals are separate.
In DVI-PC mode, adjustments are only Vertical size, and Horizontal size.
AUDIO
CENTER
MODE IN
P
R
DVI INPUT
DTV/DVD
(480i/480p/720p/1080i)
COMPONENT
INPUT2 INPUT1
PB
Y
PC/DTV (XGA/ 480p/ 720p/ 1080i)
PC/DTV (XGA/ 480p/ 720p/ 1080i)
RGB INPUT
UPGRADE PORT
RGB/DVI INPUT
(R)
(L)
AUDIO
(R)
(L)
AUDIO
(R)
(L)
AUDIO
VARIABLE
AUDIO OUT
MODE Resolution Horizontal Vertical
640x350 31.5KHz 70Hz 640x480 31.5KHz 60Hz 640x480 37.9KHz 72Hz 640x480 37.5KHz 75Hz 800x600 35.2KHz 56Hz 800x600 37.9KHz 60Hz 800x600 48.1KHz 72Hz 800x600 46.9KHz 75Hz
1024x768 48.4KHz 60Hz
1024x768 56.5KHz 70Hz 1024x768 60.0KHz 75Hz
SVGA
VGA
Text
XGA
RGB-PC/DVI-PC Input
Select RGB-PC Source and press ENTER. Use UP/DOWN arrows to select the desired options (H-Position/V-Position/H-Size/V­Size/Phase) and then use LEFT/RIGHT arrow to make appropriate adjustments.
-
Horizontal position, Vertical position, Horizontal size, and Vertical
size: Based on the input mode (resolution), the adjustment
ranges may change.
-
PHASE: Removes any horizontal noise and clears up or sharpens
the character images. Adjustment range is -15 ~ + 15.
Computer
In RGB-PC/DVI-PC modes, for POP or Twin screen, H­Position/V-Position/H-Size/V-Size/Phase are not adjustable.
PAGE 15
External Stereo Connections
1
2
Locate both Variable Audio Out jacks on the back of your TV and the Left/Right audio input jacks on the back of your stereo's amplifier.
Connect these jacks, making sure that they are connected correctly. (red=Right, white=Left.)
Adjust the sound on your stereo, according to directions provided with the amplifier.
3
Connect Left/Right Variable Audio Output to an external Audio Amplifier System.
AUDIO
CENTER
MODE IN
P
R
DVI INPUT
DTV/DVD
(480i/480p/720p/1080i)
COMPONENT
INPUT2 INPUT1
PB
Y
PC/DTV (XGA/ 480p/ 720p/ 1080i)
PC/DTV (XGA/ 480p/ 720p/ 1080i)
RGB INPUT
UPGRADE PORT
RGB/DVI INPUT
(R)
(L)
AUDIO
(R)
(L)
AUDIO
(R)
(L)
AUDIO
VARIABLE
AUDIO OUT
MONITOR
OUT
VIDEO
INPUT 2
VIDEO
INPUT 1
S-VIDEO
(R)
(L)
AUDIO
VIDEO
MONO
+75
ANT IN
Analog stereo amplifier
A/V cables not included with TV
PAGE 16
Home Theater: Speaker Layout
sub-woofer
right speaker
left
speaker
surround
sound
speaker
surround sound speaker
This is a typical speaker layout. Any number of other speaker setups are possible, and some changes may be needed to maximize your sound. However, a Dolby Digital Receiver is required to hear 5.1 channel audio.
Left and right speakers on each side of the TV enhance separation. The TV's sound optional hookup center mode in, makes the dialog sound as though its coming directly from the TV. The rear surround sound speakers provide the majority of other sounds, like those from special effects in movies. Your sub-woofer generates ultra-low frequency sound, for rumbling low-end audio.
Sound is affected by speaker placement, so make sure nothing is in front of the speakers, and that they are aimed in appropriate directions.
You have the option of turning the TV speakers on or off.
PAGE 17
Monitor Out Setup
Your TV has a special signal output capa­bility which allows you to hook up a sec­ond TV or monitor.
Just connect the second TV or monitor to the MONITOR OUT Audio/Video jacks locat­ed on the back of your TV. See the Operating Manual of the second TV or monitor for further details regarding that devices input settings.
1
2
Audio
Video
S-Video
AUDIO
CENTER
MODE IN
P
R
DVI INPUT
DTV/DVD
(480i/480p/720p/1080i)
COMPONENT
INPUT2 INPUT1
PB
Y
PC/DTV (XGA/ 480p/ 720p/ 1080i)
PC/DTV (XGA/ 480p/ 720p/ 1080i)
RGB INPUT
UPGRADE PORT
RGB/DVI INPUT
(R)
(L)
AUDIO
(R)
(L)
AUDIO
(R)
(L)
AUDIO
VARIABLE
AUDIO OUT
MONITOR
OUT
VIDEO
INPUT 2
VIDEO
INPUT 1
S-VIDEO
(R)
(L)
AUDIO
VIDEO
MONO
+75
ANT IN
PB
Component 1 - 2, RGB-DTV/PC, and DVI-DTV/PC input sources for main picture cannot be used for Monitor Out.
A/V Cables
Not included
with TV
Second TV
PAGE 18
Remote Control Functions in TV Mode
1 2 3
4 5 6
7 8 9
0
TV
MODE
LIGHT
POWER
TV/VIDEO
DVI
RGB
VCR
CABLE
DVD
SAT
MUTE
SWAPPIPCH- PIPCH+
PIP
RATIO
RECORD
STOP
PAUSE
REW
PLAY
FF
MENU EXIT
CC FREEZE
PIP INPUT
VOL
CH
SURF
SAP
VIDEO
COMP2COMP1
SIDE
SKIP
ENTER
FLASHBK
SURF
Scrolls the Surf channel list.
MENU
Brings up the main menu
to the screen.
EXIT
Clears all on-screen displays and returns to TV viewing from any menu.
FREEZE
Captures and freezes the currently­viewed main picture.
VIDEO
Adjusts the factory preset pic­ture according to the room.
PIPCH+
Changes to next higher PIP channel.
SWAP
Switches the picture from PIP, POP, or twin picture to the main screen.
MUTE
Switches the sound on or off
THUMBSTICK
Allows you to navigate the on-screen
menus and to adjust the system set-
tings and preferences, by moving to
an option with
F G
and selecting the
highlighted option with .
TV/VIDEO
Selects: Analog, Video1, Video2, Side video, Component1-2, RGB,
and DVI input sources.
MODE
Selects the remote operating mode:
TV, VCR, Cable, DVD and Satellite. Select other operating modes, for
the remote to control external
devices.
SIDE
Selects the side video signal if a
device, such as a camcorder or
game player, is connected to the
side video input jack.
DVI
Selects: DVI-DTV and DVI-PC input sources.
SAP
Selects: Mono, Stereo, and SAP.
PIPCH-
Changes to next lower
PIP channel
PIP
Toggles between PIP, POP
(Picture-out-of-Picture) and
Twin picture mode.
LIGHT
Illuminates the remote control keys.
INDICATOR LIGHTS
Show active remote mode every time any button is pressed.
D E
Loading...
+ 42 hidden pages