Page 1
LCD TV
SERVICE MANUAL
CAUTION
BEFORE SERVICING THE CHASSIS,
READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
CHASSIS : ML-041B
MODEL: RM-15LA70C
website:http://biz.LGservice.com
e-mail:http://www.LGEservice.com/techsup.html
R
Page 2
- 2 -
CONTENTS
CONTENTS .............................................................................................. 2
PRODUCT SAFETY ..................................................................................3
SPECIFICATION........................................................................................4
TIMING CHART........................................................................................11
ADJUSTMENT INSTRUCTION ...............................................................12
TROUBLE SHOOTING............................................................................16
BLOCK DIAGRAM...................................................................................21
WIRING DIAGRAM..................................................................................23
EXPLODED VIEW .................................................................................. 24
EXPLODED VIEW PARTS LIST..............................................................25
REPLACEMENT PARTS LIST ............................................................... 26
SVC. SHEET ...............................................................................................
Page 3
- 3 -
SAFETY PRECAUTIONS
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the
Schematic Diagram and Replacement Parts List.
It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent
X-RADIATION, Shock, Fire, or other Hazards.
Do not modify the original design without permission of manufacturer.
General Guidance
An isolation Transformer should always be used during the
servicing of a receiver whose chassis is not isolated from the AC
power line. Use a transformer of adequate power rating as this
protects the technician from accidents resulting in personal injury
from electrical shocks.
It will also protect the receiver and it's components from being
damaged by accidental shorts of the circuitry that may be
inadvertently introduced during the service operation.
If any fuse (or Fusible Resistor) in this TV receiver is blown,
replace it with the specified.
When replacing a high wattage resistor (Oxide Metal Film Resistor,
over 1W), keep the resistor 10mm away from PCB.
Keep wires away from high voltage or high temperature parts.
X-RAY Radiation
Warning:
To determine the presence of high voltage, use an accurate high
impedance HV meter.
Adjust brightness, color, contrast controls to minimum.
Measure the high voltage.
The meter reading should indicate
23.5 ¡ 1.5KV: 14-19 inch, 26 ¡ 1.5KV: 19-21 inch,
29.0 ¡ 1.5KV: 25-29 inch, 30.0 ¡ 1.5KV: 32 inch
If the meter indication is out of tolerance, immediate service and
correction is required to prevent the possibility of premature
component failure.
Before returning the receiver to the customer,
always perform an AC leakage current check on the exposed
metallic parts of the cabinet, such as antennas, terminals, etc., to
be sure the set is safe to operate without damage of electrical
shock.
Leakage Current Cold Check(Antenna Cold Check)
With the instrument AC plug removed from AC source, connect an
electrical jumper across the two AC plug prongs. Place the AC
switch in the on position, connect one lead of ohm-meter to the AC
plug prongs tied together and touch other ohm-meter lead in turn to
each exposed metallic parts such as antenna terminals, phone
jacks, etc.
If the exposed metallic part has a return path to the chassis, the
measured resistance should be between 1MΩ and 5.2MΩ.
When the exposed metal has no return path to the chassis the
reading must be infinite.
An other abnormality exists that must be corrected before the
receiver is returned to the customer.
Leakage Current Hot Check (See below Figure)
Plug the AC cord directly into the AC outlet.
Do not use a line Isolation Transformer during this check.
Connect 1.5K/10watt resistor in parallel with a 0.15uF capacitor
between a known good earth ground (Water Pipe, Conduit, etc.)
and the exposed metallic parts.
Measure the AC voltage across the resistor using AC voltmeter
with 1000 ohms/volt or more sensitivity.
Reverse plug the AC cord into the AC outlet and repeat AC voltage
measurements for each exposed metallic part. Any voltage
measured must not exceed 0.75 volt RMS which is corresponds to
0.5mA.
In case any measurement is out of the limits specified, there is
possibility of shock hazard and the set must be checked and
repaired before it is returned to the customer.
Leakage Current Hot Check circuit
The source of X-RAY RADIATION in this TV receiver is the High
Voltage Section and the LCD PANEL.
For continued X-RAY RADIATION protection, the replacement
panel must be the same type panel as specified in the
Replacement Parts List.
IMPORTANT SAFETY NOTICE
0.15uF
To Instrument's
exposed
METALLIC PARTS
AC Volt-meter
1.5 Kohm/10W
Good Earth Ground
such as WATER PIPE,
CONDUIT etc.
Page 4
- 4 -
CAUTION: Before servicing receivers covered by this service
manual and its supplements and addenda, read and follow the
SAFETY PRECAUTIONS on page 3 of this publication.
NOTE: If unforeseen circumstances create conflict between the
following servicing precautions and any of the safety precautions on
page 3 of this publication, always follow the safety precautions.
Remember: Safety First.
General Servicing Precautions
1. Always unplug the receiver AC power cord from the AC power
source before;
a. Removing or reinstalling any component, circuit board
module or any other receiver assembly.
b. Disconnecting or reconnecting any receiver electrical plug or
other electrical connection.
c. Connecting a test substitute in parallel with an electrolytic
capacitor in the receiver.
CAUTION: A wrong part substitution or incorrect polarity
installation of electrolytic capacitors may result in an
explosion hazard.
2. Test high voltage only by measuring it with an appropriate high
voltage meter or other voltage measuring device (DVM,
FETVOM, etc) equipped with a suitable high voltage probe.
Do not test high voltage by "drawing an arc".
3. Do not spray chemicals on or near this receiver or any of its
assemblies.
4. Unless specified otherwise in this service manual, clean
electrical contacts only by applying the following mixture to the
contacts with a pipe cleaner, cotton-tipped stick or comparable
non-abrasive applicator; 10% (by volume) Acetone and 90% (by
volume) isopropyl alcohol (90%-99% strength)
CAUTION: This is a flammable mixture.
Unless specified otherwise in this service manual, lubrication of
contacts in not required.
5. Do not defeat any plug/socket B+ voltage interlocks with which
receivers covered by this service manual might be equipped.
6. Do not apply AC power to this instrument and/or any of its
electrical assemblies unless all solid-state device heat sinks are
correctly installed.
7. Always connect the test receiver ground lead to the receiver
chassis ground before connecting the test receiver positive
lead.
Always remove the test receiver ground lead last.
8. Use with this receiver only the test fixtures specified in this
service manual.
CAUTION: Do not connect the test fixture ground strap to any
heat sink in this receiver.
Electrostatically Sensitive (ES) Devices
Some semiconductor (solid-state) devices can be damaged easily
by static electricity. Such components commonly are called
Electrostatically Sensitive (ES) Devices. Examples of typical ES
devices are integrated circuits and some field-effect transistors and
semiconductor "chip" components. The following techniques
should be used to help reduce the incidence of component
damage caused by static by static electricity.
1. Immediately before handling any semiconductor component or
semiconductor-equipped assembly, drain off any electrostatic
charge on your body by touching a known earth ground.
Alternatively, obtain and wear a commercially available
discharging wrist strap device, which should be removed to
prevent potential shock reasons prior to applying power to the
unit under test.
2. After removing an electrical assembly equipped with ES
devices, place the assembly on a conductive surface such as
aluminum foil, to prevent electrostatic charge buildup or
exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ES
devices.
4. Use only an anti-static type solder removal device. Some solder
removal devices not classified as "anti-static" can generate
electrical charges sufficient to damage ES devices.
5. Do not use freon-propelled chemicals. These can generate
electrical charges sufficient to damage ES devices.
6. Do not remove a replacement ES device from its protective
package until immediately before you are ready to install it.
(Most replacement ES devices are packaged with leads
electrically shorted together by conductive foam, aluminum foil
or comparable conductive material).
7. Immediately before removing the protective material from the
leads of a replacement ES device, touch the protective material
to the chassis or circuit assembly into which the device will be
installed.
CAUTION: Be sure no power is applied to the chassis or circuit,
and observe all other safety precautions.
8. Minimize bodily motions when handling unpackaged
replacement ES devices. (Otherwise harmless motion such as
the brushing together of your clothes fabric or the lifting of your
foot from a carpeted floor can generate static electricity
sufficient to damage an ES device.)
General Soldering Guidelines
1. Use a grounded-tip, low-wattage soldering iron and appropriate
tip size and shape that will maintain tip temperature within the
range or 500
O
F to 600OF.
2. Use an appropriate gauge of RMA resin-core solder composed
of 60 parts tin/40 parts lead.
3. Keep the soldering iron tip clean and well tinned.
4. Thoroughly clean the surfaces to be soldered. Use a mall wirebristle (0.5 inch, or 1.25cm) brush with a metal handle.
Do not use freon-propelled spray-on cleaners.
5. Use the following unsoldering technique
a. Allow the soldering iron tip to reach normal temperature.
(500
O
F to 600OF)
b. Heat the component lead until the solder melts.
c. Quickly draw the melted solder with an anti-static, suction-
type solder removal device or with solder braid.
CAUTION: Work quickly to avoid overheating the
circuitboard printed foil.
6. Use the following soldering technique.
a. Allow the soldering iron tip to reach a normal temperature
(500
O
F to 600OF)
b. First, hold the soldering iron tip and solder the strand against
the component lead until the solder melts.
c. Quickly move the soldering iron tip to the junction of the
component lead and the printed circuit foil, and hold it there
only until the solder flows onto and around both the
component lead and the foil.
CAUTION: Work quickly to avoid overheating the circuit
board printed foil.
d. Closely inspect the solder area and remove any excess or
splashed solder with a small wire-bristle brush.
SERVICING PRECAUTIONS
Page 5
- 5 -
IC Remove/Replacement
Some chassis circuit boards have slotted holes (oblong) through
which the IC leads are inserted and then bent flat against the
circuit foil. When holes are the slotted type, the following technique
should be used to remove and replace the IC. When working with
boards using the familiar round hole, use the standard technique
as outlined in paragraphs 5 and 6 above.
Removal
1. Desolder and straighten each IC lead in one operation by gently
prying up on the lead with the soldering iron tip as the solder
melts.
2. Draw away the melted solder with an anti-static suction-type
solder removal device (or with solder braid) before removing the
IC.
Replacement
1. Carefully insert the replacement IC in the circuit board.
2. Carefully bend each IC lead against the circuit foil pad and
solder it.
3. Clean the soldered areas with a small wire-bristle brush.
(It is not necessary to reapply acrylic coating to the areas).
"Small-Signal" Discrete Transistor
Removal/Replacement
1. Remove the defective transistor by clipping its leads as close as
possible to the component body.
2. Bend into a "U" shape the end of each of three leads remaining
on the circuit board.
3. Bend into a "U" shape the replacement transistor leads.
4. Connect the replacement transistor leads to the corresponding
leads extending from the circuit board and crimp the "U" with
long nose pliers to insure metal to metal contact then solder
each connection.
Power Output, Transistor Device
Removal/Replacement
1. Heat and remove all solder from around the transistor leads.
2. Remove the heat sink mounting screw (if so equipped).
3. Carefully remove the transistor from the heat sink of the circuit
board.
4. Insert new transistor in the circuit board.
5. Solder each transistor lead, and clip off excess lead.
6. Replace heat sink.
Diode Removal/Replacement
1. Remove defective diode by clipping its leads as close as
possible to diode body.
2. Bend the two remaining leads perpendicular y to the circuit
board.
3. Observing diode polarity, wrap each lead of the new diode
around the corresponding lead on the circuit board.
4. Securely crimp each connection and solder it.
5. Inspect (on the circuit board copper side) the solder joints of
the two "original" leads. If they are not shiny, reheat them and if
necessary, apply additional solder.
Fuse and Conventional Resistor
Removal/Replacement
1. Clip each fuse or resistor lead at top of the circuit board hollow
stake.
2. Securely crimp the leads of replacement component around
notch at stake top.
3. Solder the connections.
CAUTION: Maintain original spacing between the replaced
component and adjacent components and the circuit board to
prevent excessive component temperatures.
Circuit Board Foil Repair
Excessive heat applied to the copper foil of any printed circuit
board will weaken the adhesive that bonds the foil to the circuit
board causing the foil to separate from or "lift-off" the board. The
following guidelines and procedures should be followed whenever
this condition is encountered.
At IC Connections
To repair a defective copper pattern at IC connections use the
following procedure to install a jumper wire on the copper pattern
side of the circuit board. (Use this technique only on IC
connections).
1. Carefully remove the damaged copper pattern with a sharp
knife. (Remove only as much copper as absolutely necessary).
2. carefully scratch away the solder resist and acrylic coating (if
used) from the end of the remaining copper pattern.
3. Bend a small "U" in one end of a small gauge jumper wire and
carefully crimp it around the IC pin. Solder the IC connection.
4. Route the jumper wire along the path of the out-away copper
pattern and let it overlap the previously scraped end of the good
copper pattern. Solder the overlapped area and clip off any
excess jumper wire.
At Other Connections
Use the following technique to repair the defective copper pattern
at connections other than IC Pins. This technique involves the
installation of a jumper wire on the component side of the circuit
board.
1. Remove the defective copper pattern with a sharp knife.
Remove at least 1/4 inch of copper, to ensure that a hazardous
condition will not exist if the jumper wire opens.
2. Trace along the copper pattern from both sides of the pattern
break and locate the nearest component that is directly
connected to the affected copper pattern.
3. Connect insulated 20-gauge jumper wire from the lead of the
nearest component on one side of the pattern break to the lead
of the nearest component on the other side.
Carefully crimp and solder the connections.
CAUTION: Be sure the insulated jumper wire is dressed so the
it does not touch components or sharp edges.
Page 6
- 6 -
1. Application range
This specification is applied to ML-041B chassis.
2. Requirement for Test
Testing for standard of each part must be followed in below
condition.
(1) Temperature: 25°C ± 2°C
(2) Humidity: 65% ± 10%
(3) Power: Standard input voltage (AC 100-240V, 50/60Hz)
(4) Measurement must be performed after heat-run more than
30min.
(5) Adjusting standard for this chassis is followed a special
standard.
SPECIFICATION
NOTE : Specifications and others are subject to change without notice for improvement
.
3.General Specification
1
2
3
Maker
Type
ActiveDisplay Area
Pixel Pitch [mm]
Electrical Interface
Color Depth
Size [mm]
Surface Treatment
Operating Mode
Back light Unit
R/T Typ.
Maker
Type
ActiveDisplay Area
Pixel Pitch [mm]
Electrical Interface
Color Depth
Size [mm]
Surface Treatment
Operating Mode
Back light Unit
R/T Typ.
Maker
Type
ActiveDisplay Area
Pixel Pitch [mm]
Electrical Interface
Color Depth
Size [mm]
Surface Treatment
Operating Mode
Back light Unit
R/T Typ.
LPL
TFT Color LCD Module
15.0 inches(380.16mm) diagonal(Aspect 4:3)
0. 0.297mm(H)x0.297mm(V)xRGB
LVDS
6BIT WITH FRC, 16,777,216 colors
332.8(H)x262.2(V)x18(D)
Anti Glare(HAZE 3%), Hard Coating(3H)
Normally Black,
4 CCFL(4 lamps)
R.T.:10ms + F.T.:22ms (MAX)
HYDIS
TFT Color LCD Module
15.0 inches(380.16mm) diagona
0. 0.297mm(H)x0.297mm(V)xRGB
LVDS
RGB 6-BIT 16,194,277Colors
331.6(H)x254.7(V)x12.7(D)
HAZE25,Hard Coating,
ANTI- Glare (3H)
Normally Black
4 CCFL(4 lamps)
T total(Tr+Td) = 25ms
CMO
TFT Color LCD Module
15.0 inches(380.16mm) diagona
0. 0 304.1mm(H)x228.1mm(V)xRGB
LVDS
RGB 6-BIT 16,194,277Colors
331.6(H)x254.6(V)x13(D)
Hard Coating, ANTI- Glare (3H)
Normally WHITE
4 CCFL(4 lamps)
R.T.:22ms + F.T.:38ms (MAX)
Item Specification Remark
No.
LPL
HYDIS
CMO
Page 7
- 7 -
4. Feature and Function
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
Teletext
REMOCON
AV Input
S-Vedio Input
Component input
PERI TV Connector
RGB(VGA)Input
H/p input
PC Sound input
RS-232
Discrete IR
2 Carrier Stereo
NICAM Stereo
2 Carrier Dual
NICAM Dual
DW(Double Window) Mode
MW(Multi Window) Mode
Film Mode
Noise Reduction
Progressive Scan
Motion Detection
SRS WOW
wivel Speaker
Ez-pip
ARC
DRP
DCDI
HDCP
TOP, FLOF,LIST 10 page
NEC Code
2
1
1
Full SCART : 1
1
1
1
YES
YES
BG, DK
BG, I, LL'
BG, DK
BG, I, LL'
X
X
O
X
O
X
X
X
X
X
O
X
X
Item Specification Remark
No.
Top(option)
PAL/ NTSC
Rear(option, NT),
Rear
Rear (option, NT), Except Commercial
Rear (option,EU)
D-sub 15 pin
Rear (option,Commercial)
Rear (option,Commercial)
5.Optical Character
Item RemarkSpecification
Viewing Angle
<CR
10>
Luminance
Contrast Ratio
CIE Color Coordinates
Typical
MAX/MIN
ALL white/All back
Min =Typ.-0.03
Max =Typ.+0.03
R/L,
U/D
Luminance(cd/
)
Variation
LPL
450
1.3
400
0.289
0.304
0.619
0.343
0.298
0.578
0.289
0.304
WHITE
RED
Green
Blue
W
X
W
Y
W
r
Y
r
X
g
Y
g
Xb
Yb
Typ.
Typ.
Typ.
Typ.
Typ.
Typ.
Typ.
Typ.
HYDIS
80/65
80/65
500
1.33
0.265
0.293
0.629
0.340
0.255
0.601
0.141
0.071
AUO
60/60
40/60
500
300
0.314
0.344
0.632
0.361
0.295
0.598
0.142
0.102
No.
1
2
3
4
Page 8
- 8 -
6-1.General Specification(TV)
1
2
3
4
5
6
7
Video input applicable system
Receivable broadcasting system
RF input channel
Input voltage
Tuning system
Operting environment
Storage environment
1)PAL-D/K,B/G,I
2)NTSC-M
3)SECAM NTSC 4.43’
1)PAL/SECAM BG
2)PAL/SECAM DK
3)PAL I/I
4)SECAM L/L’
5)NTSC M
6)PAL-N/M
7)NTSC M
VHF : E2 ~ E12
UHF : E21 ~ E69
CATV : S1 ~ S20
HYPER : S21 ~ S41
L/L’ : B,C,D
VHF : 2 ~ 13
UHF : 14 ~ 69
CATV : 1 ~ 125
VHF Low : 1~M10
VHF High : 4~S22
UHF : S23~62
AC 100 - 240V/ 50Hz,60HZ
FVS 100 program
FS
1)Temp : 0 ~ 40 deg
2)Humidity : 85%
3)Temp : -20 ~ 60 deg
4)Humidity : 85%
Item Specification Remark
No.
EU/Non-EU(RZ/RT)
(PAL Market)
7)NTSC Area(RM)
PAL
FRANCE
NTSC
JAPAN
PAL, 200PR.(Option)
NTSC
6.Engineering Specification
Page 9
- 9 -
6-2.Power
NO
1
2
3
4
5
6
7
8
9
10
11
AC Power Shut Down Voltage
DC Voltage, Inverter
DC Voltage, LCD Panel
DC Voltage, Audio
DC Voltage, Tuner(5)
DC Voltage, Tuner(9)
DC Voltage, Tuning(31)
DC Voltage, VCTi(5)
DC Voltage, VCTi(8)
DC Voltage, VCTi(3.3)
DC Voltage, VCTi(1.8)
DC Voltage, GM2221 (3.3)
DC Voltage, GM2221 (1.8)
DC Voltage, Digital (3.3)
DC Voltage, Digital (5)
90
22.8
11.4
14.0
4.5
8.5
31
4.5
7.5
3.1
1.6
3.1
1.6
2.8
4.5
24
12
15
5
9
33
5
8
3.3
1.8
3.3
1.8
3.3
5
264
25.2
12.6
16.0
5.5
9.5
35
5.5
8.5
3.5
2.0
3.5
2.0
3.8
5.5
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
Japan only
Item Min Typ Max Unit Remark
1
2
3
4
5
Power Supply
Normal
Stand By
Suspend Mode
DPM Off Mode
Cut-off Switch off
ITEM
D-SUB Pin Configuraion
Control Function
Y, Pb, Pr
D4 Jack
(525i, 525p, 750p, 1125i)
H/V Sync
On/On
Off/On
On/Off
Off/Off
-
Spectification
1: RED
3: Blue:
5: S.T(GND)
7: Green GND
9: N.C
11: ID0(GND)
13: H-Sync
15: SCL
1) Contrast/Brightness
2) H-Position/V-Position
3) Tracking : Clock/ Phase
4) Auto Configure
RESET
1: Y
3: Pb
5: Pr
7: Line1 Ready
9: LINE2
11: LINE3
5) 13: Line3 Ready
2: Green
4: ID2(GND)
6: RED GND
8: Blue GND
10: D-GND
12: SDA
14: V-Sync
Shell: GND
2: Y GND
4: Pb GND
6: Pr GND
8: LINE1
10: Line2 Ready
12: SWITCH GND
6) 14: SWITCH
Remark
10: Digital GND
Middle east/
NTSC Area
JAPAN Only
Video
Active
Off
-
Power Consumption
¡´ 55W
¡´ 1W
¡´ 1W
¡´ 1W
0W
PBP SWAP ¢” ON/OFF
Item Specification Remark
No.
LED Color
GREEN
RED
OFF
Page 10
- 10 -
7. Signal Timing(Resolution)
7-1. PC Mode
6-3. Power
NO
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
Video Input Level
Audio Input Level
Audio Input Frequency Response
Audio Input S/N
Audio Input Distortion
Audio Input Dynamic Range
Video Output Level
Video Output Frequency Response
Video Output S/N
Audio Output Level
Audio Output Frequency Response
Audio Output S/N
Audio Output Distortion
Video Input Level, R/G/B
Video Input Level, Component(Y, PB, PR)
RGB Input Resolution, Vertical
RGB Input Resolution, Horizontal
RGB Input Horizontal Frequency
RGB Input Frame Rate
0.85
0.4
0.1
40
2
0.85
3.8
40
0.4
0.1
40
0.6
0.6
1
0.5
1
0.5
0.7
0.7
768
1280
1.15
0.6
7
2
1.15
0.6
7
2
0.8
0.8
Vpp
V
KHz
DB
%
V
Vpp
MHz
DB
V
KHz
DB
%
Vpp
Vpp
Pixel
Pixel
KHz
Hz
EN-50049
NTSC:0.4Vrms(Typ)
75 ohm
75 ohm
Only 20" 640 Pixel
480
See table 5-5
See table 5-5
Item Min Typ Max Unit Remark
6-4. The Others
NO
1
2
3
4
5
6
Search Sensitivity
Soft Ware Functionality Test
REMOCON Working Sensitivity, Straight
REMOCON Working Sensitivity, T/B/L/R
Closed Caption Sensitivity
Teletext Sensitivity
0.1
0.1
-85
10
9
-70
-70
dBm
m
m
dBm
dBm
LGE Specification
30 degree
NTSC ONLY
Item Min Typ Max Unit Remark
Mode
H_display
V_display
V frequency
H_total
H_blanking
H_sync
H Polarity
H_bp
H_fp
H-freq[kHz]
/Clk[MHz]
V_total
V_blanking
V_sync
V Polarity
V_bp
V_fp
VGA-60
640
480
60
800
160
96
NEG.
48
16
31.469
25.175
525
45
2
NEG
33
10
VGA-67
640
480
67
864
224
64
NEG.
96
64
35.0
30.24
525
45
3
NEG
39
3
VGA-75
640
480
75
840
200
64
NEG
120
16
37.5
31.5
500
20
3
NEG
16
1
SVGA-56
800
600
56
1024
224
72
POS
128
24
35.156
36.0
625
25
2
POS
22
1
SVGA-60
800
600
60
1056
256
128
POS
88
40
37.879
40.0
628
28
4
POS
23
1
SVGA-72
800
600
72
1040
240
120
POS
64
56
48.077
50.0
666
66
6
POS
23
37
SVGA-75
800
600
75
1056
256
80
POS
160
16
46.875
49.5
625
25
3
POS
21
1
XGA-70
1024
768
70
1328
304
136
NEG
144
24
56.476
75.0
806
38
6
NEG
29
3
XGA-75
1024
768
75
1312
288
96
POS
176
16
60.023
78.75
800
32
3
POS
28
1
XGA-60 X
1024
768
60
1344
304
136
NEG
136
160
48.3
65
806
38
6
NEG
29
3
[Table 7] Timming chart of Receivable Mode * H [dot] / V [line]
Page 11
TIMING CHART
- 11 -
VIDEO
SYNC
D
B
C
E
A
<< Dot Clock (MHz), Horizontal Frequency (kHz), Vertical Frequency (Hz), Horizontal etc... (µs), Vertical etc... (ms) >>
H + 31.468 800 640 16 96 48
V – 70.090 449 350 37 2 60
H – 31.469 800 640 16 96 48
V – 59.94 525 480 10 2 33
H – 37.5 840 640 16 64 120
V – 75 500 480 1 3 16
H – 31.469 900 720 18 108 54
V + 70.082 449 400 13 2 34
H + 37.879 1056 800 40 128 88
V + 60.317 628 600 1 4 23
H + 46.875 1056 800 16 80 160
V + 75.0 625 600 1 3 21
H – 48.363 1344 1024 24 136 160
V – 60.004 806 768 3 6 21
Mode
H/V
Sort
1
2
3
4
5
6
7
25.175
28.324
25.175
31.5
40.0
49.5
65.0
640x350
640x480
800x600
720x400
800x600
800x600
1024x768
Sync
Polarity
Frequency
Dot
Clock
Total Period
(E)
Video Active Time
(A)
Sync Duration
(D)
Back Porch
(F)
Front Porch
(B)
Resolution
Page 12
- 12 -
ADJUSTMENT INSTRUCTION
1. Application Object
This instruction is for the application to the LCD TV.
2. Adjustment
2.1 Adjustment overview
The unit is set to automatically adjust using the
factory automation equipment. However when errors
occur, it should be adjusted manually.
2.2 Auto Gain/Offset adjustment
2.2.1 RF Mode adjustment
2.2.1.1 Adjustment preparation
¡ÆConduct Heat Run at the RF fog signals for more than
30 minutes.
2.2.1.2 Auto Gain/Offset adjustment
¡ÆPress IN-START Key to convert to the adjustment
mode using the adjustment (SVC) remote controller,
and press VOL+ Key at the Auto Gain menu.
(In case of RM-15LA70, press IN-START Key twice)
¡ÆOnce the adjustment is completed, press the Enter
Key to save and finish the adjustment.
2.2.2 PC Mode adjustment
2.2.2.1 Adjustment preparation
¡ÆConduct Heat Run at the RF fog signals for more than
30 minutes.
¡ÆConnect the Pattern Generator to 15 Pin D-Sub Jack
of LCD TV.
2.2.2.2 Auto Gain/Offset adjustment
¡ÆConvert the input mode to PC input.
¡ÆUsing the Pattern Generator (801GF, VG819) adjust
WXGA (1280 X 768) for resolution and 16 Step Gray
signals for the pattern. Or adjust the 16 Step (11 Step)
Gray signals in accordance with VG819.
¡ÆConvert the input mode to PC input and convert to
the adjustment mode using the adjustment (SVC)
remote controller and pressing the IN-START Key,
and then press VOL+ Key at the AutoGain menu.
¡ÆOnce the adjustment is completed, press the Enter
Key to save and finish the adjustment.
2.3
EDID (The Extended Display Identification Data) setting
¡ÆConnect the 15 Pin D-Sub Cable to D-Sub Jack.
¡ÆSet the input mode of Set to PC.
¡ÆConnect the DDC automation equipment to write
DDC data.
2.3.1 EDID DATA
00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F
00 00 FF FF FF FF FF FF 00 1E 6D 9F 3B 01 01 01 01
10 04 0E 01 03 28 1E 17 78 EA B1 45 A1 58 4F 95 26
20 1D 50 54 AF EE 00 31 4F 45 4F 61 4F 01 01 01 01
30 01 01 01 01 01 01 64 19 00 40 41 00 26 30 18 88
40 36 00 30 E4 10 00 00 18 00 00 00 FD 00 38 4B 1E
50 3F 08 00 0A 20 20 20 20 20 20 00 00 00 FC 00 52
60 4D 31 35 4C 41 37 30 0A 20 20 20 20 00 00 00 FC
70 00 20 20 20 20 20 20 20 20 20 20 20 20 20 00 73
Page 13
- 13 -
NO ITEM
CONDITION
REMARK
1
2
3
4
5
6
7
8
1
2
3
4
5
6
Side AV
SCART
PC
SideComp
16:9
200PR
Text
ACMS
HiDev
Hotel
Top
I II SAVE
Turbo Vol
Ch/Aus
1
1
1
1
1
0
1
1
0
0
1
1
0
0
0: Side AV Off
1: Side AV On
0: SCART Off
1: SCART On
0: PC Off
1: PC On
0: SideComp Off
1: SideComp On
0: Wide Off
1: Wide On
0: 100 Program
1: 200 Program
0: Text Off
1: Text On
0: ACMS On
1: ACMS Off
0: HiDev Off
1: HiDev On
0: Hotel Off
1: Hotel On
0: Top Off
1: Top On
0:
Ch. Sound Non Memory
1:
Ch. Sound Memory
0:
except below area(Off)
1:
Middle-east Area Vol On
0:
except below area(Off)
1:
China, Australia On
Option 1
Option 2
NO ITEM
CONDITION
REMARK
1
2
3
4
Language
Txt Lang
Inch opt
Panel
1
0
2
7
0: Eng Only
1:
EU5+
12 nations(Europe)
2:
Same As Option '1'
3: Eng + Chines
4: Eng + Arab + Urdu
5: Eng + FARSI
0: WEST EU
1: EAST EU 1
2:
TURKY EU
3: EAST EU 2
4: CYRILLIC 1
5: CYRILLIC 2
6: CYRILLIC 3
7:
TURKY GRE
1
8:
TURKY GRE
2
9:
TURKY GRE
3
10:
ARAB FRAN
11:
ARAB ENG
12:
ARAB HEB
1
13:
ARAB HEB
2
14:
FARSI ENG
15:
FARSI FRA
16:
FARI ALL
0. 13"
1. 15"
2. 17"
3. 20"
0:VGA CMO
1:VGA LPL
2:VGA AUO
3:SVGA AUO
4:XGA LPL
5:XGA CMO
6:XGA HYD
7:WXGA LPL
8:WXGA AUO
Option 3
*Option(PAL)
Page 14
- 14 -
EDID ADJUSTMENT
Windows EDID V1.0 User Manual
Operating System: MS Windows 98, 2000, XP
Port Setup: Windows 98 => Don’t need setup
Windows 2000, XP => Need to Port Setup.
This program is available to LCD Monitor only.
1. Port Setup
a) Copy “UserPort.sys” file to
“c:\WINNT\system32\drivers” folder
b) Run Userport.exe
c) Remove all default number
d) Add 300-3FF
e) Click Start button.
f) Click Exit button.
2. EDID Read & Write
1) Run WinEDID.exe
2) Edit Week of Manufacture, Year of Manufacture,
Serial Number
a) Input User Info Data
b) Click “Update” button
c) Click “ Write” button
Figure 1. Cable Connection
Video Signal
Generator
C
Control Line
A
IBM
Compatible PC
Not used
RS232C
PARALLEL
VGS
MONITOR
V-SYNC
B
220
POWER
ST
Power LED
E
ST Switch
F
V-Sync On/Off Switch
(Switch must be ON.)
Power inlet (required)
Power Select Switch
(110V/220V)
PARALLEL PORT
5V
OFF ON
F
A
69
1
15
10
5
5
11
6
1
13
25
ON
5V
E
OFF
74LS06
B
C
1
14
5V
4.7K
4.7K
74LS06
4.7K
Page 15
- 15 -
SVC REMOCON
NO KEY FUNTION
REAMARK
1 POWER
2 POWER ON
3 MUTE
4 P-CHECK
5 S-CHECK
6 ARC
7 CAPTION
8 TXT
9 TV/AV
10 TURBO SOUND
11 TURBO PICTURE
12 IN-START
13 ADJ
14 MPX
15 EXIT
16 APC(PSM)
17 ASC(SSM)
18 MULTIMIDIA
19 FRONT-AV
20 CH¡
21 VOL¡
22 ENTER
23 PIP CH-(OP1)
24 PIP CH+(OP2)
25 PIP SWAP(OP3)
26 PIP INPUT(OP4)
27 EYE
28 MENU
29 IN-STOP
30 STILL
31 TIME
32 SIZE
33 MULTI PIP
34 POSITION
35 MODE
36 PIP
37 TILT
38 0~9
To turn the TV on or off
To turn the TV on automatically if the power is supplied to the TV. (Use the
POWER key to deactivate): It should be deactivated when delivered.
To activate the mute function.
To check TV screen image easily.
To check TV screen sound easily
To select size of the main screen (Normal, Spectacle, Wide or Zoom)
Switch to closed caption broadcasting
To toggle on/off the teletext mode
To select an external input for the TV screen
To start turbo sound
To start turbo picture
To enter adjustment mode when manufacturing the TV sets.
To adjust the screen voltage (automatic):
In-start
mute Adjust AV(Enter into W/B adjustment mode)
W/B adjustment (automatic):
After adjusting the screen W/B adjustment Exit two times (Adjustment completed)
To enter into the adjustment mode. To adjust horizontal line and sub-brightness.
To select the multiple sound mode (Mono, Stereo or Foreign language)
To release the adjustment mode
To easily adjust the screen according to surrounding brightness
To easily adjust sound according to the program type
To check component input
To check the front AV
To move channel up/down or to select a function displayed on the screen.
To adjust the volume or accurately control a specific function.
To set a specific function or complete setting.
To move the channel down in the PIP screen.
To use as a red key in the teletext mode
To move the channel in the PIP screen
To use as a green key in the teletext mode
To switch between the main and sub screens
To use as a yellow key in the teletext mode
To select the input status in the PIP screen
To use as a blue key in the teletext mode
To set a function that will automatically adjust screen status to match
the surrounding brightness so natural color can be displayed.
To select the functions such as video, voice, function or channel.
To set the delivery condition status after manufacturing the TV set.
To halt the main screen in the normal mode, or the sub screen at the PIP screen.
Used as a hold key in the teletext mode (Page updating is stopped.)
Displays the teletext time in the normal mode
Enables to select the sub code in the teletext mode
Used as the size key in the PIP screen in the normal mode
Used as the size key in the teletext mode
Used as the index key in the teletext mode (Top index will be
displayed if it is the top text.)
To select the position of the PIP screen in the normal mode
Used as the update key in the teletext mode (Text will be
displayed if the current page is updated.)
Used as Mode in the teletext mode
To select the simultaneous screen
To adjust screen tilt
To manually select the channel.
Shortcut keys
Shortcut keys
Shortcut keys
Use the AV
key to enter
the screen
W/B
adjustment
mode.
Shortcut keys
Shortcut keys
Shortcut keys
Page 16
- 16 -
TROUBLESHOOTING
No power
(LED indicator off)
Check short of main B/D
or Change Lips
Change IC1107, IC1104
Change LED Assy
Check 15V or 5V
of Lips
Check Output of
IC1107, IC104
Check LED Assy
Check P1100, P210 Connector
Fail
Fail
Change Q1100
Check Output of
Q1100
Fail
Pass
Fail
Pass
Pass
Pass
:[A]Process
Page 17
- 17 -
No Raster
Check LED Status
on display unit
Check the input/
Output of IC901
Check L900,L901
L902,L903
Check inverter
Connector or inverter
Check input source cable and jack
Repeat A PROCESS
Fail
Change L900,L901,
L902,L903
Fail
Change IC901
Fail
Change inverter
connector or inverter
Fail
Change panel link
cable or module
Fail
Change module
Fail
Check panel link
Cable or module
Pass
Pass
Pass
Pass
:[B]Process
Page 18
- 18 -
No Raster on Component signal
Check JA1200 or
RCA CABLE
Check the signal of
L1200, L1202, L1203
Repeat
[A] Process
Check the input/
output of IC1
Check the input/
output of IC901
Check input source cable and jack
Fail
Re-soldering or
Change the defect part,
Check X11
Fail
Re-soldering or
Change the defect part,
Check X900
Fail
Pass
Pass
Pass
Check the input/output
of IC800, IC851
Re-soldering or
Change the defect part
Fail
Pass
Page 19
- 19 -
No Raster on AV Signal
(Video, S-Video)
No Raster on TV(RF) signal
Change L1209, L1210,
L1212
Check the signal of
L1209, L1210, L1212
Repeat
[A] Process
Check the output of
TU1000
Check the input/output
of IC1
Check the input/output
of IC800, IC851
Check input source cable and jack
Fail
Fail
Fail
Fail
Re-soldering or
Change the defect part
Chek X11
Fail
Re-soldering or
Change the defect part
Check 5V, 33V of TU1000
Re-soldering or
Change the defect part
Pass
Pass
Pass
Check the input/output
of IC901
Fail
Re-soldering or
Change the defect part
Check X900
Pass
Pass
Page 20
- 20 -
No Sound
Check the speaker wire
Change source input
Check the
input source
Fail
Pass
Re-soldering or
Change the defect part
Check X11
Check the input/output
of IC1
Fail
Pass
Re-soldering or
Change the defect part
Check the input/output
of IC100,IC101
Fail
Pass
Change speaker
Check the speaker
Fail
Pass
Page 21
BLOCK DIAGRAM
- 21 -
Page 22
BLOCK DIAGRAM DESCRIPTION
- 22 -
1. Video Controller Unit & Display Data Conversion Unit
The video controller unit receives the video signals inputted through the tuner, AV port (AV1, AV2, S-Video,
component), and converts them into an analog RGB signal through the microcomputer (VCTI) combined with
the video decoder that integrates various functions in one chip.
Either the analog RGB, component YPbPr or PC RGB signal is selected by the switching IC and inputted to a
scaler (GM2221), which is sent to the LCD module after being modified to an LVDS signal through the
integrated LVDS IC.
Or, it is sent to the LCD module as a TTL output.
VCTi is the main microprocessor that handles video signal processing and sound signal processing. It also
manages the RF signals received from the tuner.
The scaler can control timing to fit into the LCD panel, and can also control the size and position of the input
signal.
2. Power Supply Unit
The power supply unit provides 15V and 5V DC power to the mainboard.
The PWM Step-Up DC/DC Converter circuit is used to generate the 33V used for the tuner.
15V power is directly used by the sound amplifier IC and is also used to generate 5V power through the
regulator. 12V power is used for the LCD panel power, and 5V power is converted to 3.3V and 1.8V power
through the regulator, which in turn supplies electrical power for ICs such as VCTI and scaler.
Page 23
- 23 -
WIRING DIAGRAM
No. Part No.
1
2
3
4
5
6
7
8
Wiring Part List
6631T25019Y
6631T11012R
6631T20028G
6631T20033U
6631T25021A
6620K00007C
6631T11017S
220MM
3P_2.5MM H-B
5
LOCAL KEY
2
1. 20P LVDS : 200MM
2. 41P TTL
3. 50P TTL : 145MM
SIDE AV
(17LZ50 ONLY)
9
4P_2.0MM H-B
3
IR_LED
4
600MM
(17LZ50 ONLY)
6P_2.0MM H-B
1
54MM
54MM
(RZ ONLY)
8
7
18P_1.0MM FFC
18P_1.0MM FFC
11P_2.0MM H-H
100MM
4P_2.5MM SHIELD RECEPTERCLE
GND: 2PIN, 4PIN
500MM 750MM
6
2P_AC_SOCKET
SPEAKER SPEAKER
Page 24
- 24 -
EXPLODED VIEW
160
150
040
030
120
100
090
130
140
110
080
020
190
170
180
200
220
210
060
070
050
010
050
Page 25
- 25 -
EXPLODED VIEW PARTS LIST
No.
PART NO.
DESCRIPTION
3091TKB051F CABINET ASSEMBLY, RM-15LA70 BRAND 3090V00525 LG
3091TKB051D CABINET ASSEMBLY, RM-15LA70 BRAND 3090V00525 CANADA SKD
6304FLP133A
LCD(LIQUID CRYSTAL DISPLAY), LC150X02-A4 LG PHILPS TFT COLOR TN,XGA,450NITS,8BITS LVDS
3809TKB030K BACK COVER ASSEMBLY, RM-15LA70C 3808V00433 COMMERCIAL
3809TKB030L BACK COVER ASSEMBLY, RM-15LA70C 3808V00433 SKD COMMERCIAL
4811V00075A BRACKET ASSEMBLY, STAND RZ-15LA70 ML024E .
3043TKK181A TILT SWIVEL ASSEMBLY, RM-15LA70 . 4811V00075
6400GKTX01C
SPEAKER,FULLRANGE, F1527C-6428-4 K-TONE FULL-RANGE(GENERAL) 4 OHM 7/12W 85DB OTHERS 40*70MM TRACK TYPE
6871TST562A
PWB(PCB) ASSEMBLY,SUB, RM-20LA77 ML041B SUB TOTAL BRAND CONTROL BOARD ASSY
6871TST691A
PWB(PCB) ASSEMBLY,SUB, RM-15LA70 ML-041B SUB TOTAL BRAND IR BOARD ASSY
4951TKS168A METAL ASSEMBLY, FRAME MAIN 15LA66/70 (LPL MODULE ONLY)
4951TKS168B METAL ASSEMBLY, FRAME MAIN C/SKD 15LA66/70 LPL MODULE ONLY
3313TN1023A MAIN TOTAL ASSEMBLY, RM-15LA70C LPL COMMERCIAL BRAND ML-041B
6871TPT281D
PWB(PCB) ASSEMBLY,POWER, L173SAB(MFM) POWER TOTAL POWERNET LIPS FOR LPL
6871TPT281A
PWB(PCB) ASSEMBLY,POWER, RZ-15LA70 POWER TOTAL POWERNET LIPS FOR CMO/LPL/HD
6871TST733A
PWB(PCB) ASSEMBLY,SUB, ML-041B COMMERCIAL JACK ASSY BOARD SUB TOTAL BRAND 1.0
4950TKS300C METAL, SHIELD 15LA70
4950TKS300H METAL, SHIELD ML041B,RZ15LA70,CKD
3551TKK537E COVER ASSEMBLY, RM-15LA70C REAR A/V RS-232C
4810V00925B BRACKET, REAR AV RZ-15LA70 ML024E HIPS .
5020V00874A BUTTON, CONTROL, RZ-15LA70 ABS, HF-380 8KEY .
3550V00385A COVER, REAR, AV RZ-15LA70 ABS, HF-380 .
4950V00157F METAL, HINGE ASSY NON 15LA70
4810V00777D BRACKET, STAND RU-15LA61 ML012C HIPS 60HR FRONT
4810V00778D BRACKET, STAND RU-15LA61 ML012C HIPS 60HR REAR
4810V00928A BRACKET, STAND RZ-15LA70 NON ABS, HF-380 .
4950V00194A METAL, STAND SPCC(CR) SUPPORTER(LA70)
4950V00190A METAL, BASE SPCC(CR) 3T RZ-15LA70
010
020
030
040
050
060
070
080
090
100
110
120
130
140
150
160
170
180
190
200
210
220
Page 26
- 26 -
DATE: 2004. 08. 31.
*S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION
C1008 0CE227CF638 "220UF SHL,SD 16V M FM5 TP 5"
C1101 0CE227BH638 220U KME 25V M FM5 TP5
C1104 0CE227BH638 220U KME 25V M FM5 TP5
C1107 0CE477BH618 470UF KME TYPE 25V M FL TP 5
C1140 0CE227BH638 220U KME 25V M FM5 TP5
C1152 0CE107BK638 100UF KME 50V M FM5 TP5
C123 0CE477BH618 470UF KME TYPE 25V M FL TP 5
C124 0CE477BH618 470UF KME TYPE 25V M FL TP 5
C131 0CE477BH618 470UF KME TYPE 25V M FL TP 5
C132 0CE477BH618 470UF KME TYPE 25V M FL TP 5
C133 0CE477BH618 470UF KME TYPE 25V M FL TP 5
C134 0CE477BH618 470UF KME TYPE 25V M FL TP 5
C1108 0CH3105F946 1UF 16V Z F 2012 R/TP
C1112 0CH3105F946 1UF 16V Z F 2012 R/TP
C1150 0CH3105F946 1UF 16V Z F 2012 R/TP
C1151 0CH3104K946 100000PF 50V Z F 2012 R/TP
C127 0CH3104K946 100000PF 50V Z F 2012 R/TP
C128 0CH3104K946 100000PF 50V Z F 2012 R/TP
C135 0CH3104K946 100000PF 50V Z F 2012 R/TP
C136 0CH3104K946 100000PF 50V Z F 2012 R/TP
C15 0CH3104K946 100000PF 50V Z F 2012 R/TP
C16 0CH3104K946 100000PF 50V Z F 2012 R/TP
C19 0CH3104K946 100000PF 50V Z F 2012 R/TP
C203 0CH3104K946 100000PF 50V Z F 2012 R/TP
C206 0CH3104K946 100000PF 50V Z F 2012 R/TP
C4 0CH3104K946 100000PF 50V Z F 2012 R/TP
C41 0CH3104K946 100000PF 50V Z F 2012 R/TP
C44 0CH3104K946 100000PF 50V Z F 2012 R/TP
C49 0CH3104K946 100000PF 50V Z F 2012 R/TP
C6 0CH3104K946 100000PF 50V Z F 2012 R/TP
C851 0CH3104K946 100000PF 50V Z F 2012 R/TP
C854 0CH3104K946 100000PF 50V Z F 2012 R/TP
C855 0CH3104K946 100000PF 50V Z F 2012 R/TP
C861 0CH3104K946 100000PF 50V Z F 2012 R/TP
C863 0CH3104K946 100000PF 50V Z F 2012 R/TP
C865 0CH3104K946 100000PF 50V Z F 2012 R/TP
C866 0CH3104K946 100000PF 50V Z F 2012 R/TP
C867 0CH3104K946 100000PF 50V Z F 2012 R/TP
C869 0CH3104K946 100000PF 50V Z F 2012 R/TP
C871 0CH3104K946 100000PF 50V Z F 2012 R/TP
C874 0CH3104K946 100000PF 50V Z F 2012 R/TP
C875 0CH3104K946 100000PF 50V Z F 2012 R/TP
C877 0CH3104K946 100000PF 50V Z F 2012 R/TP
C909 0CH3104K946 100000PF 50V Z F 2012 R/TP
C910 0CH3104K946 100000PF 50V Z F 2012 R/TP
C917 0CH3104K946 100000PF 50V Z F 2012 R/TP
C920 0CH3104K946 100000PF 50V Z F 2012 R/TP
C925 0CH3104K946 100000PF 50V Z F 2012 R/TP
C926 0CH3104K946 100000PF 50V Z F 2012 R/TP
C927 0CH3104K946 100000PF 50V Z F 2012 R/TP
C928 0CH3104K946 100000PF 50V Z F 2012 R/TP
C929 0CH3104K946 100000PF 50V Z F 2012 R/TP
C930 0CH3104K946 100000PF 50V Z F 2012 R/TP
DATE: 2004. 08. 31.
*S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION
C934 0CH3104K946 100000PF 50V Z F 2012 R/TP
C935 0CH3104K946 100000PF 50V Z F 2012 R/TP
C936 0CH3104K946 100000PF 50V Z F 2012 R/TP
C937 0CH3104K946 100000PF 50V Z F 2012 R/TP
C938 0CH3104K946 100000PF 50V Z F 2012 R/TP
C939 0CH3104K946 100000PF 50V Z F 2012 R/TP
C940 0CH3104K946 100000PF 50V Z F 2012 R/TP
C943 0CH3104K946 100000PF 50V Z F 2012 R/TP
C944 0CH3104K946 100000PF 50V Z F 2012 R/TP
C945 0CH3104K946 100000PF 50V Z F 2012 R/TP
C946 0CH3104K946 100000PF 50V Z F 2012 R/TP
C947 0CH3104K946 100000PF 50V Z F 2012 R/TP
C948 0CH3104K946 100000PF 50V Z F 2012 R/TP
C949 0CH3104K946 100000PF 50V Z F 2012 R/TP
C950 0CH3104K946 100000PF 50V Z F 2012 R/TP
C956 0CH3104K946 100000PF 50V Z F 2012 R/TP
C964 0CH3104K946 100000PF 50V Z F 2012 R/TP
C965 0CH3104K946 100000PF 50V Z F 2012 R/TP
C967 0CH3104K946 100000PF 50V Z F 2012 R/TP
C968 0CH3104K946 100000PF 50V Z F 2012 R/TP
C970 0CH3104K946 100000PF 50V Z F 2012 R/TP
C13 0CH6102K406 1000PF 50V J SL 2012 R/TP
C14 0CH6102K406 1000PF 50V J SL 2012 R/TP
C2 0CH6102K406 1000PF 50V J SL 2012 R/TP
C20 0CH6102K406 1000PF 50V J SL 2012 R/TP
C201 0CH6471K416 470F 50V J NP0 2012 R/TP
C202 0CH6471K416 470F 50V J NP0 2012 R/TP
C204 0CH6471K416 470F 50V J NP0 2012 R/TP
C205 0CH6471K416 470F 50V J NP0 2012 R/TP
C21 0CH6102K406 1000PF 50V J SL 2012 R/TP
C46 0CH6102K406 1000PF 50V J SL 2012 R/TP
C50 0CH6102K406 1000PF 50V J SL 2012 R/TP
C59 0CH6102K406 1000PF 50V J SL 2012 R/TP
C889 0CH6331K416 330PF 50V J NP0 2012 R/TP
C890 0CH6331K416 330PF 50V J NP0 2012 R/TP
C891 0CH6331K416 330PF 50V J NP0 2012 R/TP
C923 0CH6080K116 8PF 50V D NP0 2012 R/TP
C924 0CH6080K116 8PF 50V D NP0 2012 R/TP
C129 181-007F "MPE ECQ-V1H224JL3(TR), 50V 0."
C130 181-007F "MPE ECQ-V1H224JL3(TR), 50V 0."
C1007 0CH3103K516 10000PF 50V 10% B(Y5P) 2012 R
C1010 0CK273DK51A 27000PF 2012 50V 10% B(Y5P) R
C1015 0CH5390K416 39PF 50V 5% NP0 2012 R/TP
C1016 0CH5390K416 39PF 50V 5% NP0 2012 R/TP
C107 0CK225DFK4A "2.2UF 2012 16V 20%,-20% F(Y5V"
C109 0CH3103K516 10000PF 50V 10% B(Y5P) 2012 R
C110 0CH3103K516 10000PF 50V 10% B(Y5P) 2012 R
C1113 0CK106EF56A 10UF 3216 16V 10% X7R R/TP
C1114 0CK106EF56A 10UF 3216 16V 10% X7R R/TP
C113 0CK225DFK4A "2.2UF 2012 16V 20%,-20% F(Y5V"
C900 0CH3103K516 10000PF 50V 10% B(Y5P) 2012 R
C902 0CH3103K516 10000PF 50V 10% B(Y5P) 2012 R
C1001 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5
C1002 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5
REPLACEMENT PARTS LIST
MAIN BOARD
CAPACITOR
For Capacitor & Resistors, the
charactors at 2nd and 3rd digit in the
P/No. means as follows;
CC, CX, CK, CN, CH : Ceramic
CQ : Polyestor
CE : Electrolytic
CF : Fixed Film
RD : Carbon Film
RS : Metal Oxide Film
RN : Metal Film
RH : CHIP, Metal Glazed(Chip)
RR : Drawing
Page 27
- 27 -
DATE: 2004. 08. 31.
*S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION
C1003 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5
C1004 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5
C1005 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5
C11 0CK474CH94A "0.47UF 1608 25V 80%,-20% R/TP"
C114 0CK225DFK4A "2.2UF 2012 16V 20%,-20% F(Y5V"
C115 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C116 0CK562CK51A 5600PF 1608 50V 10% R/TP B(Y5
C117 0CK562CK51A 5600PF 1608 50V 10% R/TP B(Y5
C118 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C12 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C125 0CK105EK56A 1UF 3216 50V 10% X7R R/TP
C126 0CK105EK56A 1UF 3216 50V 10% X7R R/TP
C200 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C22 0CK822CK56A 8200PF 1608 50V 10% X7R R/TP
C23 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C24 0CK822CK56A 8200PF 1608 50V 10% X7R R/TP
C25 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C26 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C27 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C28 0CK334CF94A "0.33UF 1608 16V 80%,-20% F(Y5"
C29 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C3 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C30 0CK334CF94A "0.33UF 1608 16V 80%,-20% F(Y5"
C31 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C32 0CK334CF94A "0.33UF 1608 16V 80%,-20% F(Y5"
C33 0CK334CF94A "0.33UF 1608 16V 80%,-20% F(Y5"
C34 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C35 0CK334CF94A "0.33UF 1608 16V 80%,-20% F(Y5"
C37 0CK334CF94A "0.33UF 1608 16V 80%,-20% F(Y5"
C40 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C42 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C45 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C52 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C67 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C75 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C82 0CK474CH94A "0.47UF 1608 25V 80%,-20% R/TP"
C858 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C901 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5
C903 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5
C904 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5
C905 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5
C906 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5
C911 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C912 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C913 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C914 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C915 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C916 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C918 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C919 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C921 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C922 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C961 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C97 0CK105CF94A "1UF 1608 16V 80%,-20% R/TP F("
C121 0CC100CK41A 10PF 1608 50V 5% R/TP NP0
C122 0CC100CK41A 10PF 1608 50V 5% R/TP NP0
C43 0CC102CK41A 1000PF 1608 50V 5% R/TP NP0
C47 0CC220CK41A 22PF 1608 50V 5% R/TP NP0
C48 0CC220CK41A 22PF 1608 50V 5% R/TP NP0
C53 0CC102CK41A 1000PF 1608 50V 5% R/TP NP0
C56 0CC221CK41A 220PF 1608 50V 5% R/TP NP0
C57 0CC221CK41A 220PF 1608 50V 5% R/TP NP0
DATE: 2004. 08. 31.
*S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION
C58 0CC221CK41A 220PF 1608 50V 5% R/TP NP0
C74 0CC102CK41A 1000PF 1608 50V 5% R/TP NP0
C83 0CC102CK41A 1000PF 1608 50V 5% R/TP NP0
C85 0CC102CK41A 1000PF 1608 50V 5% R/TP NP0
C86 0CC102CK41A 1000PF 1608 50V 5% R/TP NP0
C88 0CC390CK41A 39PF 1608 50V 5% R/TP NP0
C89 0CC390CK41A 39PF 1608 50V 5% R/TP NP0
C98 0CC102CK41A 1000PF 1608 50V 5% R/TP NP0
C1106 0CE477BD618 470UF KME TYPE 10V 20% FL TP
C108 0CE476VH6DC 47UF MV 25V 20% R/TP(SMD) SMD
C1100 0CE107WF6DC 100UF MVK 16V 20% R/TP(SMD) S
C1102 0CE227WF6DC 220UF MVK 16V 20% R/TP(SMD) S
C1103 0CE107WF6DC 100UF MVK 16V 20% R/TP(SMD) S
C1105 0CH8476F691 47UF 16V 20% 105STD (CYL) R/T
C1109 0CE107WF6DC 100UF MVK 16V 20% R/TP(SMD) S
C111 0CE475WJ6DC 4.7UF MVK 35V 20% R/TP(SMD) S
C1118 0CE107WF6DC 100UF MVK 16V 20% R/TP(SMD) S
C112 0CE475WJ6DC 4.7UF MVK 35V 20% R/TP(SMD) S
C1124 0CE107WF6DC 100UF MVK 16V 20% R/TP(SMD) S
C1130 0CE107WF6DC 100UF MVK 16V 20% R/TP(SMD) S
C1132 0CE107WF6DC 100UF MVK 16V 20% R/TP(SMD) S
C1134 0CE227WF6DC 220UF MVK 16V 20% R/TP(SMD) S
C1135 0CE107WF6DC 100UF MVK 16V 20% R/TP(SMD) S
C1137 0CE107WF6DC 100UF MVK 16V 20% R/TP(SMD) S
C1149 0CE107WF6DC 100UF MVK 16V 20% R/TP(SMD) S
C119 0CH8106F691 10UF 16V 20% 105STD (CYL) R/T
C120 0CH8106F691 10UF 16V 20% 105STD (CYL) R/T
C17 0CE475WJ6DC 4.7UF MVK 35V 20% R/TP(SMD) S
C5 0CE475WJ6DC 4.7UF MVK 35V 20% R/TP(SMD) S
C55 0CE475VK6DC 4.7UF MV 50V 20% R/TP(SMD) SM
C60 0CE475VK6DC 4.7UF MV 50V 20% R/TP(SMD) SM
C852 0CH8476F691 47UF 16V 20% 105STD (CYL) R/T
C856 0CH8476F691 47UF 16V 20% 105STD (CYL) R/T
C859 0CH8476F691 47UF 16V 20% 105STD (CYL) R/T
C864 0CH8476F691 47UF 16V 20% 105STD (CYL) R/T
C868 0CH8476F691 47UF 16V 20% 105STD (CYL) R/T
C87 0CE107WF6DC 100UF MVK 16V 20% R/TP(SMD) S
C873 0CH8476F691 47UF 16V 20% 105STD (CYL) R/T
C888 0CE107WF6DC 100UF MVK 16V 20% R/TP(SMD) S
C90 0CH8106F691 10UF 16V 20% 105STD (CYL) R/T
C96 0CE107WF6DC 100UF MVK 16V 20% R/TP(SMD) S
C99 0CH8106F691 10UF 16V 20% 105STD (CYL) R/T
D100 0DRFC00288A SS14 FAIR CHILD R/TP SMA 20-1
D101 0DRFC00288A SS14 FAIR CHILD R/TP SMA 20-1
D1150 0DRGS00199A UF4001 GENERAL SEMICONDUCTOR
D102 0DS181009AA KDS181 TP KEC SOT-23 80V 30
D103 0DS181009AA KDS181 TP KEC SOT-23 80V 30
D107 0DS226009AA KDS226 TP KEC SOT-23 80V 300
ZD104 0DZ620009HB UDZ S 6.2B TP ROHM SOD323 200
ZD105 0DZ620009HB UDZ S 6.2B TP ROHM SOD323 200
ZD209 0DZ510009EE UDZ S 5.1B TP ROHM-K SOD323 2
ZD210 0DZ510009EE UDZ S 5.1B TP ROHM-K SOD323 2
ZD200 0DZ510009EE UDZ S 5.1B TP ROHM-K SOD323 2
ZD201 0DZ510009EE UDZ S 5.1B TP ROHM-K SOD323 2
ZD202 0DZ510009EE UDZ S 5.1B TP ROHM-K SOD323 2
ZD203 0DZ510009EE UDZ S 5.1B TP ROHM-K SOD323 2
ZD204 0DZ510009EE UDZ S 5.1B TP ROHM-K SOD323 2
ZD205 0DZ510009EE UDZ S 5.1B TP ROHM-K SOD323 2
ZD206 0DZ510009EE UDZ S 5.1B TP ROHM-K SOD323 2
DIODEs
Page 28
DATE: 2004. 08. 31.
*S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION
ZD211 0DZ510009EE UDZ S 5.1B TP ROHM-K SOD323 2
D1151 0DZ330009DF MTZJ33B TP ROHM-K DO34 0.5W 3
IC905 0IZZTSA004B "ML-041B WXGA NT 17"" COMMERCIA"
IC3 0IKE702700D "KIA7027AF 3, SOT-89 TP RESET"
IC200 0IMMRSG036A "M24C02-WMN6T SGS-THOMSON 8P,S"
IC4 0IMCRAL006A AT24C16AN-10SI-2.7 ATMEL 8P S
IC903 0IMCRAL006A AT24C16AN-10SI-2.7 ATMEL 8P S
IC100 0IMCRMZ002A MP7720 MONOLITHIC POWER SYSTE
IC101 0IMCRMZ002A MP7720 MONOLITHIC POWER SYSTE
IC851 0IMCRMI006A "M52758FP MITSUBISHI 36PIN, R/"
IC202 0IMO140662A "MC14066BDR2 14P,SOIC TP BILAT"
IC1 0IPRPMN003C VCT49XYF C7(NTSC+PAL) MICRONA
IC901 0IPRPGN015A "GM2221-BC GENESIS 208P,QFP TR"
IC1111 0IMCRFA015A KA7805R FAIRCHILD 2P D-PAK R/
IC1101 0IPMGFA061A "FAN1587AD33X FAIRCHILD 3P,DPA"
IC1103 0IPMGSG018D "LD1086DT18TR SGS-THOMSON 3P,D"
IC1105 0IPMGFA061A "FAN1587AD33X FAIRCHILD 3P,DPA"
IC1106 0IPMGSG018D "LD1086DT18TR SGS-THOMSON 3P,D"
IC1108 0IMCRKE010A KIA7812AF KEC 2P DPACK R/TP 1
IC1114 0IPMGFA061A "FAN1587AD33X FAIRCHILD 3P,DPA"
IC1115 0IPMGFA061A "FAN1587AD33X FAIRCHILD 3P,DPA"
IC1110 0ISS780800J "KA78M08R 3P,D-PAK TP VOL. REG"
IC1113 0ISS780800J "KA78M08R 3P,D-PAK TP VOL. REG"
IC222 0IMCRTI001A SN74HCT157D TEXAS INSTRUMENT
L104 6140TBZ045A "38.5UH(DIP), 6A, P7.5, DR8.3X"
L105 6140TBZ045A "38.5UH(DIP), 6A, P7.5, DR8.3X"
L1150 150-985B DR8*11 2.4MH 0.16MM 270.5T
L1100 6210TCE001G HH-1M3216-501 CERATEC 3216MM
L1101 6210TCE001G HH-1M3216-501 CERATEC 3216MM
L1103 6210TCE001A HB-1S2012-080JT CERATEC 2012M
L1104 6210TCE001A HB-1S2012-080JT CERATEC 2012M
L1105 6210TCE001G HH-1M3216-501 CERATEC 3216MM
L1106 6210TCE001G HH-1M3216-501 CERATEC 3216MM
L1107 6210TCE001G HH-1M3216-501 CERATEC 3216MM
L200 6210TCE001A HB-1S2012-080JT CERATEC 2012M
L201 6210TCE001A HB-1S2012-080JT CERATEC 2012M
L202 6210TCE001A HB-1S2012-080JT CERATEC 2012M
L203 6210TCE001A HB-1S2012-080JT CERATEC 2012M
L204 6210TCE001G HH-1M3216-501 CERATEC 3216MM
L853 6210TCE001G HH-1M3216-501 CERATEC 3216MM
L900 6210TCE001G HH-1M3216-501 CERATEC 3216MM
L901 6210TCE001G HH-1M3216-501 CERATEC 3216MM
L902 6210TCE001G HH-1M3216-501 CERATEC 3216MM
L903 6210TCE001G HH-1M3216-501 CERATEC 3216MM
L905 6210TCE001A HB-1S2012-080JT CERATEC 2012M
L1102 6210TCE001G HH-1M3216-501 CERATEC 3216MM
L205 6210TCE001A HB-1S2012-080JT CERATEC 2012M
L906 6210TCE001G HH-1M3216-501 CERATEC 3216MM
L907 6210TCE001G HH-1M3216-501 CERATEC 3216MM
L10 0LC1032101A 10UH 10% 3216 R/TC FI-C3216-1
L1002 0LC1032101A 10UH 10% 3216 R/TC FI-C3216-1
L15 0LC1032101A 10UH 10% 3216 R/TC FI-C3216-1
L888 0LC0233002A 3.3UH CERATECH R/TP
L889 0LC0233002A 3.3UH CERATECH R/TP
L890 0LC0233002A 3.3UH CERATECH R/TP
L1001 0LC1020101A 1UH 10% 2012 R/TC FI-B2012-10
DATE: 2004. 08. 31.
*S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION
L2 0LC1032101A 10UH 10% 3216 R/TC FI-C3216-1
L8 0LC1032101A 10UH 10% 3216 R/TC FI-C3216-1
IC1107 0TF492509AA SI4925DY TP TEMIC 30V 6.1A S
Q1150 0TR322809AB KTC3228-Y(KTC2383) TP KEC TO9
Q603 0TR387500AA CHIP 2SC3875S(ALY) BK KEC - Q100 0TR387500AA CHIP 2SC3875S(ALY) BK KEC - Q1000 0TR388109AA KTC3881 CHIP TP KEC - Q101 0TR150400BA CHIP 2SA1504S(ASY) BK KEC - Q1100 0TR387500AA CHIP 2SC3875S(ALY) BK KEC - Q1151 0TR387500AA CHIP 2SC3875S(ALY) BK KEC - Q12 0TR150400BA CHIP 2SA1504S(ASY) BK KEC - Q13 0TR150400BA CHIP 2SA1504S(ASY) BK KEC - Q14 0TR150400BA CHIP 2SA1504S(ASY) BK KEC - Q15 0TR387500AA CHIP 2SC3875S(ALY) BK KEC - IC902 0TFVI80005A VISHAY SI4963DY R/TP SO-8 -20
IC1104 0TFVI80005A VISHAY SI4963DY R/TP SO-8 -20
R1010 0RH7501D622 7.5K 1/10W 5 D.R/TP
R1012 0RH7502D622 75K 1/10W 5 D.R/TP
R106 0RH1500D622 150 1/10W 5 D.R/TP
R107 0RH1003D622 100K 1/10W 5 D.R/TP
R1108 0RH1003D622 100K 1/10W 5 D.R/TP
R1109 0RH1003D622 100K 1/10W 5 D.R/TP
R1149 0RH2200D622 220 1/10W 5 D.R/TP
R1150 0RH0102D622 10 1/10W 5 D.R/TP
R1151 0RH4700D622 470 1/10W 5 D.R/TP
R1153 0RH1000D622 100 1/10W 5 D.R/TP
R126 0RH4701D622 4.7K 1/10W 5 D.R/TP
R132 0RH1003D622 100K 1/10W 5 D.R/TP
R133 0RH1003D622 100K 1/10W 5 D.R/TP
R134 0RH1003D622 100K 1/10W 5 D.R/TP
R135 0RH1003D622 100K 1/10W 5 D.R/TP
R140 0RH0392D622 39 1/10W 5 D.R/TP
R141 0RH0392D622 39 1/10W 5 D.R/TP
R142 0RH0392D622 39 1/10W 5 D.R/TP
R143 0RH0392D622 39 1/10W 5 D.R/TP
R144 0RH0392D622 39 1/10W 5 D.R/TP
R145 0RH0392D622 39 1/10W 5 D.R/TP
R146 0RH0392D622 39 1/10W 5 D.R/TP
R147 0RH0392D622 39 1/10W 5 D.R/TP
R211 0RH0752D622 75 1/10W 5 D.R/TP
R212 0RH0752D622 75 1/10W 5 D.R/TP
R213 0RH0752D622 75 1/10W 5 D.R/TP
R214 0RH4701D622 4.7K 1/10W 5 D.R/TP
R217 0RH4703D622 470K 1/10W 5 D.R/TP
R74 0RH1000D622 100 1/10W 5 D.R/TP
R888 0RH0752D622 75 1/10W 5 D.R/TP
R889 0RH0752D622 75 1/10W 5 D.R/TP
R890 0RH0752D622 75 1/10W 5 D.R/TP
R908 0RH0822D622 82 1/10W 5 D.R/TP
R910 0RH0822D622 82 1/10W 5 D.R/TP
R915 0RH3600D622 CHIP 360-J 1/10 W
R934 0RH1000D622 100 1/10W 5 D.R/TP
R989 0RH8200D622 820 1/10W 5 D.R/TP
R999 0RH1000D622 100 1/10W 5 D.R/TP
R136 0RH8202D622 82K 1/10W 5 D.R/TP
R137 0RH8202D622 82K 1/10W 5 D.R/TP
- 28 -
IC
COIL & CORE & INDUCTOR
FET & TRANSISTOR
RESISTORs
Page 29
DATE: 2004. 08. 31.
*S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION
C931 0RH0000D622 0 OHM 1 / 10 W 2012 5.00% D
C932 0RH0000D622 0 OHM 1 / 10 W 2012 5.00% D
R1011 0RH0000D622 0 OHM 1 / 10 W 2012 5.00% D
R1106 0RH1002D622 10K OHM 1 / 10 W 2012 5.00% D
R1152 0RH1001D622 1K OHM 1 / 10 W 2012 5.00% D
R128 0RH1002D622 10K OHM 1 / 10 W 2012 5.00% D
R129 0RH1002D622 10K OHM 1 / 10 W 2012 5.00% D
R148 0RH0000D622 0 OHM 1 / 10 W 2012 5.00% D
R149 0RH0000D622 0 OHM 1 / 10 W 2012 5.00% D
R202 0RH0222D622 22 OHM 1 / 10 W 2012 5.00% D
R208 0RH0222D622 22 OHM 1 / 10 W 2012 5.00% D
R209 0RH0222D622 22 OHM 1 / 10 W 2012 5.00% D
R210 0RH0222D622 22 OHM 1 / 10 W 2012 5.00% D
R215 0RH0222D622 22 OHM 1 / 10 W 2012 5.00% D
R216 0RH1001D622 1K OHM 1 / 10 W 2012 5.00% D
R218 0RH1002D622 10K OHM 1 / 10 W 2012 5.00% D
R219 0RH1002D622 10K OHM 1 / 10 W 2012 5.00% D
R220 0RH0000D622 0 OHM 1 / 10 W 2012 5.00% D
R222 0RH0000D622 0 OHM 1 / 10 W 2012 5.00% D
R223 0RH0000D622 0 OHM 1 / 10 W 2012 5.00% D
R228 0RH0000D622 0 OHM 1 / 10 W 2012 5.00% D
R230 0RH0000D622 0 OHM 1 / 10 W 2012 5.00% D
R39 0RH0000D622 0 OHM 1 / 10 W 2012 5.00% D
R903 0RH0000D622 0 OHM 1 / 10 W 2012 5.00% D
R961 0RH0000D622 0 OHM 1 / 10 W 2012 5.00% D
R964 0RH1002D622 10K OHM 1 / 10 W 2012 5.00% D
R985 0RH0000D622 0 OHM 1 / 10 W 2012 5.00% D
R995 0RH0000D622 0 OHM 1 / 10 W 2012 5.00% D
R10 0RJ3301D677 3.3K OHM 1/10 W 5% 1608 R/TP
R1001 0RJ0562D677 56 OHM 1/10 W 5% 1608 R/TP
R1002 0RJ1501D677 1.5K OHM 1/10 W 5% 1608 R/TP
R1003 0RJ8200D677 820 OHM 1/10 W 5% 1608 R/TP
R1004 0RJ3000D677 300 OHM 1/10 W 5% 1608 R/TP
R1005 0RJ0682D677 68 OHM 1/10 W 5% 1608 R/TP
R1014 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R11 0RJ3301D677 3.3K OHM 1/10 W 5% 1608 R/TP
R1105 0RJ1001D677 1K OHM 1/10 W 5% 1608 R/TP
R1107 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
R1155 0RJ1002D677 10K OHM 1/10 W 5% 1608 R/TP
R124 0RJ1500D677 150 OHM 1/10 W 5% 1608 R/TP
R125 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
R127 0RJ2701D677 2.7K OHM 1/10 W 5% 1608 R/TP
R130 0RJ1202D677 12K OHM 1/10 W 5% 1608 R/TP
R131 0RJ1202D677 12K OHM 1/10 W 5% 1608 R/TP
R138 0RJ1002D677 10K OHM 1/10 W 5% 1608 R/TP
R139 0RJ1002D677 10K OHM 1/10 W 5% 1608 R/TP
R15 0RJ0822D677 82 OHM 1/10 W 5% 1608 R/TP
R16 0RJ2200D677 220 OHM 1/10 W 5% 1608 R/TP
R17 0RJ0822D677 82 OHM 1/10 W 5% 1608 R/TP
R18 0RJ2200D677 220 OHM 1/10 W 5% 1608 R/TP
R19 0RJ0822D677 82 OHM 1/10 W 5% 1608 R/TP
R20 0RJ2200D677 220 OHM 1/10 W 5% 1608 R/TP
R203 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R205 0RJ0222D677 22 OHM 1/10 W 5% 1608 R/TP
R206 0RJ1001D677 1K OHM 1/10 W 5% 1608 R/TP
R207 0RJ1001D677 1K OHM 1/10 W 5% 1608 R/TP
R21 0RJ0222D677 22 OHM 1/10 W 5% 1608 R/TP
R22 0RJ1500D677 150 OHM 1/10 W 5% 1608 R/TP
R221 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R224 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R225 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R226 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
DATE: 2004. 08. 31.
*S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION
R227 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R229 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R23 0RJ2701D677 2.7K OHM 1/10 W 5% 1608 R/TP
R24 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R240 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R25 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R28 0RJ0000D677 0 OHM 1/10 W 5% 1608 R/TP
R29 0RJ0000D677 0 OHM 1/10 W 5% 1608 R/TP
R34 0RJ0000D677 0 OHM 1/10 W 5% 1608 R/TP
R41 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R42 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R45 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R46 0RJ1001D677 1K OHM 1/10 W 5% 1608 R/TP
R49 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R50 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R51 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R52 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R53 0RJ1500D677 150 OHM 1/10 W 5% 1608 R/TP
R54 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R55 0RJ1500D677 150 OHM 1/10 W 5% 1608 R/TP
R56 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R58 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R60 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R62 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R64 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R66 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R68 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R69 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R70 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R72 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R73 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R75 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R76 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R77 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R78 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R80 0RJ2202D677 22K OHM 1/10 W 5% 1608 R/TP
R835 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R838 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R901 0RJ0472D677 47 OHM 1/10 W 5% 1608 R/TP
R902 0RJ0472D677 47 OHM 1/10 W 5% 1608 R/TP
R904 0RJ0472D677 47 OHM 1/10 W 5% 1608 R/TP
R907 0RJ3301D677 3.3K OHM 1/10 W 5% 1608 R/TP
R909 0RJ0822D677 82 OHM 1/10 W 5% 1608 R/TP
R911 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
R912 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R913 0RJ0000D677 0 OHM 1/10 W 5% 1608 R/TP
R914 0RJ0000D677 0 OHM 1/10 W 5% 1608 R/TP
R917 0RJ0000D677 0 OHM 1/10 W 5% 1608 R/TP
R928 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R929 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R930 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R931 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R932 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R935 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R936 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R938 0RJ1002D677 10K OHM 1/10 W 5% 1608 R/TP
R939 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R941 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R942 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R943 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R944 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R945 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
- 29 -
Page 30
DATE: 2004. 08. 31.
*S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION
R946 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R947 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R950 0RJ0000D677 0 OHM 1/10 W 5% 1608 R/TP
R951 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
R953 0RJ3301D677 3.3K OHM 1/10 W 5% 1608 R/TP
R954 0RJ1002D677 10K OHM 1/10 W 5% 1608 R/TP
R96 0RJ3301D677 3.3K OHM 1/10 W 5% 1608 R/TP
R979 0RJ3301D677 3.3K OHM 1/10 W 5% 1608 R/TP
R980 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R981 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R982 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R983 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R984 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R991 0RJ3301D677 3.3K OHM 1/10 W 5% 1608 R/TP
R992 0RJ3301D677 3.3K OHM 1/10 W 5% 1608 R/TP
X11 6202TST003C HC-49/SM5H KONY CHIP 20.25MHZ
X900 6202VDT002B SX-1 SUNNY SC14.3MHZ +/- 30 P
IC905 6620F00017A CCSD-32T-SM WOOYOUNG 32P PLCC
Z1000 6200QL3002F "X6966M EPCOS ST SIP5K, 6200QL"
TU1000 6700VS0003D TAEW-G052P LGIT MULTI VS RCA
R2200 0RN1101F409 1.10K 1/6W 1% TA52
R2201 0RN8200F409 820 1/6W 1% TA52
R2202 0RN5600F409 560 1/6W 1% TA52
R2203 0RN4700F409 470 1/6W 1 TA52
R2204 0RN3900F409 390 1/6W 1% TA52
R2205 0RN3300F409 330 1/6W 1% TA52
R2206 0RN2700F409 270 1/6W 1% TA52
R2207 0RN3301F409 3.30K 1/6W 1% TA52
R2208 0RN2000F409 200 1/6W 1% TA52
SW2200 140-313A TACT 2LEAD 100G(TA) LG C&D NO
SW2201 140-313A TACT 2LEAD 100G(TA) LG C&D NO
SW2202 140-313A TACT 2LEAD 100G(TA) LG C&D NO
SW2203 140-313A TACT 2LEAD 100G(TA) LG C&D NO
SW2204 140-313A TACT 2LEAD 100G(TA) LG C&D NO
SW2205 140-313A TACT 2LEAD 100G(TA) LG C&D NO
SW2206 140-313A TACT 2LEAD 100G(TA) LG C&D NO
SW2207 140-313A TACT 2LEAD 100G(TA) LG C&D NO
C2101 0CH3104K566 0.1UF 50V 10% X7R 2012 R/TP
L2101 6210TCE001A HB-1S2012-080JT CERATEC 2012M
Q2101 0TR387500AA CHIP 2SC3875S(ALY) BK KEC - Q2102 0TR387500AA CHIP 2SC3875S(ALY) BK KEC - Q2103 0TR387500AA CHIP 2SC3875S(ALY) BK KEC - R2101 0RH1000D622 100 1/10W 5 D.R/TP
R2102 0RH1000D622 100 1/10W 5 D.R/TP
R2103 0RH1001D622 1K OHM 1 / 10 W 2012 5.00% D
R2104 0RH1001D622 1K OHM 1 / 10 W 2012 5.00% D
R2105 0RH1001D622 1K OHM 1 / 10 W 2012 5.00% D
R2106 0RH1000D622 100 1/10W 5 D.R/TP
R2111 0RH4301D622 4.3K 1/10W 5 TA
R2113 0RH0000D622 0 OHM 1 / 10 W 2012 5.00% D
LED2100
0DL200000CA SAM5670(DL-2LRG) BK Y-GREEN -
DATE: 2004. 08. 31.
*S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION
C1215 0CH3103K516 10000PF 50V 10% B(Y5P) 2012 R
C1216 0CH3103K516 10000PF 50V 10% B(Y5P) 2012 R
C1217 0CH3104K946 100000PF 50V Z F 2012 R/TP
C1218 0CH6331K416 330PF 50V J NP0 2012 R/TP
C1219 0CH6331K416 330PF 50V J NP0 2012 R/TP
C1220 0CH6331K416 330PF 50V J NP0 2012 R/TP
L1206 6210TCE001A HB-1S2012-080JT CERATEC 2012M
L1207 6210TCE001A HB-1S2012-080JT CERATEC 2012M
L1208 6210TCE001A HB-1S2012-080JT CERATEC 2012M
L1209 0LC0233002A 3.3UH CERATECH R/TP
L1211 6210TCE001A HB-1S2012-080JT CERATEC 2012M
L1213 6210TCE001A HB-1S2012-080JT CERATEC 2012M
L1216 6210TCE001A HB-1S2012-080JT CERATEC 2012M
R1224 0RJ1000H680 100 OHM 1/2 W 5% 5025 R/TP
R1225 0RJ1000H680 100 OHM 1/2 W 5% 5025 R/TP
R1226 0RH0472D622 47 1/10W 5 D.R/TP
R1227 0RH0752D622 75 1/10W 5 D.R/TP
R1228 0RH0752D622 75 1/10W 5 D.R/TP
R1238 0RH0000D622 0 OHM 1 / 10 W 2012 5.00% D
R1239 0RH0000D622 0 OHM 1 / 10 W 2012 5.00% D
R1240 0RH0000D622 0 OHM 1 / 10 W 2012 5.00% D
ZD1210 0DZ620009HB UDZ S 6.2B TP ROHM SOD323 200
C1221 0CH6331K416 330PF 50V J NP0 2012 R/TP
C1223 0CH6471K416 470F 50V J NP0 2012 R/TP
C1224 0CH6471K416 470F 50V J NP0 2012 R/TP
C1225 0CH3104K946 100000PF 50V Z F 2012 R/TP
C1226 0CH3104K946 100000PF 50V Z F 2012 R/TP
C1227 0CH3104K946 100000PF 50V Z F 2012 R/TP
C1228 0CH3104K946 100000PF 50V Z F 2012 R/TP
C1229 0CE107WF6DC 100UF MVK 16V 20% R/TP(SMD) S
C1230 0CH6101K416 100PF 50V J NP0 2012 R/TP
IC1200 0IMCRSG010A ST3232CDR SGS-THOMSON SOP16 R
L1210 0LC0233002A 3.3UH CERATECH R/TP
L1212 0LC0233002A 3.3UH CERATECH R/TP
L1214 6210TCE001A HB-1S2012-080JT CERATEC 2012M
L1215 6210TCE001A HB-1S2012-080JT CERATEC 2012M
L1217 6210TCE001A HB-1S2012-080JT CERATEC 2012M
L1231 6210TCE001G HH-1M3216-501 CERATEC 3216MM
R1229 0RH0752D622 75 1/10W 5 D.R/TP
R1230 0RH0752D622 75 1/10W 5 D.R/TP
R1231 0RH0752D622 75 1/10W 5 D.R/TP
R1232 0RH5101D622 5.1K 1/10W 5 D.R/TP
R1233 0RH4703D622 470K 1/10W 5 D.R/TP
R1234 0RH5101D622 5.1K 1/10W 5 D.R/TP
R1235 0RH4703D622 470K 1/10W 5 D.R/TP
R1236 0RH3302D622 33K 1/10W 5 D.R/TP
R1237 0RH3302D622 33K 1/10W 5 D.R/TP
ZD1211 0DZ620009HB UDZ S 6.2B TP ROHM SOD323 200
ZD1212 0DZ620009HB UDZ S 6.2B TP ROHM SOD323 200
ZD1213 0DZ620009HB UDZ S 6.2B TP ROHM SOD323 200
ZD1214 0DZ620009HB UDZ S 6.2B TP ROHM SOD323 200
- 30 -
OTHERs
CONTROL BOARD
IR BOARD
JACK BOARD
Page 31
Page 32
Page 33
Page 34
Page 35
Page 36
Aug., 2004
Printed in KoreaP/NO : 3828TSL104Z
Loading...