LG RH298H-ML Owner’s Manual

RH298H-ML_AA1CLL_ENG

http://www.LG.ca

HDD/DVD

RECORDER

OWNER’S MANUAL

MODEL: LRH-890

Before connecting, operating or adjusting this product, please read this instruction booklet carefully and completely.

Call us and we will guide you through your first recording, for free.

1-888-542-2623

(LGCANADA)

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK

OF ELECTRIC SHOCK

DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance

(servicing) instructions in the literature accompanying the product.

WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

WARNING: Do not install this equipment in a confined space such as a book case or similar unit.

CAUTION:

Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.

Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from over heating.

The openings should be never be blocked by placing the product on a bed, sofa, rug or other similar surface.This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instruction have been adhered to.

CAUTION:

CLASS 3B VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCKS DEFEATED AVOID EXPOSURE TO THE BEAM.

CAUTION:

This product employs a Laser System.

To ensure proper use of this product, please read this owner’s manual carefully and retain it for future reference. Should the unit require maintenance, contact an authorized service center.

Performing controls, adjustments, or carrying out procedures other than those specified herein may result in hazardous radiation exposure.

To prevent direct exposure to laser beam, do not try to open the enclosure. Visible laser radiation when open. DO NOT STARE INTO BEAM.

CAUTION: The apparatus should not be exposed to water (dripping or splashing) and no objects filled with liquids, such as vases, should be placed on the apparatus.

CAUTION concerning the Power Cord

Most appliances recommend they be placed upon a dedicated circuit;

That is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the specification page of this owner's manual to be certain.

Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer.

Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance.

To disconnect power from the mains, pull out the mains cord plug. When installing the product, ensure that the plug is easily accessible.

2

IMPORTANT SAFETY INSTRUCTIONS

CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS IN THIS OWNER’S MANUAL. AND THOSE MARKED ON THE PRODUCT. RETAIN THIS BOOKLET FOR FUTURE REFERENCE.

This product has been designed and manufactured to assure personal safety. Improper use can result in electric shock or fire hazard. The safeguards incorporated in this product will protect you if you observe the following procedures for installation, use, and servicing.

This product does not contain any parts that can be repaired by the user.

DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO DANGEROUS VOLTAGE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL ONLY.

1.Read these instructions. - All these safety and operating instructions should be read before the product is operated.

2.Keep these instructions. - The safety, operating and use instructions should be retained for future reference.

3.Heed all warnings. - All warnings on the product and in the operating instructions should be adhered to.

4.Follow all instructions. - All operating and use instructions should be followed.

5.Do not use this apparatus near water. – For example: near a bath tub, wash bowl, kitchen sink, laundry tub, in a wet basement; or near a swimming pool; and other areas located near water.

6.Clean only with dry cloth. – Unplug this product from the wall outlet before cleaning.

Do not use liquid cleaners.

7.Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. -

Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from over-heating. The openings should never be

blocked by placing the product on a bed, sofa, rug or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is

provided or the manufacturer’s instructions have been adhered to.

8.Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9.Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety.

If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10.Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11.Only use attachments/accessories specified by the manufacturer.

12.Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13.Unplug this apparatus during lightning storms or when unused for long periods of time.

14.Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is

damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

<![if ! IE]>

<![endif]>Introduction

3

Contents

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-10

Symbol Used in this Manual . . . . . . . . . . . . . . . .5 Notes on Discs . . . . . . . . . . . . . . . . . . . . . . . . . .5 Recordable and Playable Discs . . . . . . . . . . . . .6 Playable Discs . . . . . . . . . . . . . . . . . . . . . . . . . .7 Regional Code . . . . . . . . . . . . . . . . . . . . . . . . . .7 Availability of copying or moving feature . . . . . . .7 About the internal hard disk drive . . . . . . . . . . . .8 Using an USB Memory Stick . . . . . . . . . . . . . . . . . .8 Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 Remote Control . . . . . . . . . . . . . . . . . . . . . . . .10 Remote Control Operation . . . . . . . . . . . . . . . .10

Hookup and Settings . . . . . . . . . . . . . . . . . .	. .11-24
Rear Panel . . . . . . . . . . . . . . . . . . . . . . . .	. . . .11
Connecting an Antenna or Cable TV . . . . .	. . . .12
Connections to Your TV . . . . . . . . . . . . . . .	. . .13
HDMI connection . . . . . . . . . . . . . . . . . . . .	. . .14
Connecting to an Amplifier . . . . . . . . . . . . .	. . .15
Accessory Audio/Video (A/V) Connections	. . . .16
Auto Set Up . . . . . . . . . . . . . . . . . . . . . . . .	. . .17
Using the Home Menu . . . . . . . . . . . . . . . .	. . .17
Initial Settings . . . . . . . . . . . . . . . . . . . . . . .	. . .18
General Operation . . . . . . . . . . . . . . . . .	. . .18
General Settings . . . . . . . . . . . . . . . . . . . .	.18-19
Tuning Band Select . . . . . . . . . . . . . . . .	. . .18
Auto Channel Set . . . . . . . . . . . . . . . . .	. . .18
To Add or Erase Channels . . . . . . . . . . .	. . .18
Auto Clock Set / Manual Clock Set . . . .	. . .19
TV Aspect . . . . . . . . . . . . . . . . . . . . . .	. . .19
Power Save Mode . . . . . . . . . . . . . . . . .	. . .19
Initialization . . . . . . . . . . . . . . . . . . . . . .	. . .19
Language Settings . . . . . . . . . . . . . . . . . . .	. . .20
Audio Settings . . . . . . . . . . . . . . . . . . . . . .	. . .20
Dolby Digital / DTS / MPEG . . . . . . . . .	. . .20
Sampling Frequency . . . . . . . . . . . . . . .	. . .20
DRC (Dynamic Range Control) . . . . . . .	. . .20
Vocal . . . . . . . . . . . . . . . . . . . . . . . . . . .	. . .20
Lock (Parental Control) Settings . . . . . . . . .	. . .21
Rating / Set Password / Area Code . . . .	. . .21
DivX Registration Code . . . . . . . . . . . .	. . .21
Recording Settings . . . . . . . . . . . . . . . . . . .	. . .22
Record Mode Set / Record Aspect . . . . .	. . .22
DV Recording Audio . . . . . . . . . . . . . . .	. . .22
Auto Chapter / MPEG4 . . . . . . . . . . . . .	. . .22
Timeshift . . . . . . . . . . . . . . . . . . . . . . . .	. . .22
Disc Settings . . . . . . . . . . . . . . . . . . . . . . .	.22-23
Disc Format . . . . . . . . . . . . . . . . . . . . .	. . .22
Finalize / Disc Label . . . . . . . . . . . . . . .	. . .23
Disc Protect / PBC . . . . . . . . . . . . . . . .	. . .23
General Explanation of On-Screen Display	. . . .24

Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25-35

General Playback Features . . . . . . . . . . . . .25-28 Playing a DivX Movie File . . . . . . . . . . . . . . . . .29 Playing an Audio CD or MP3/WMA file . . . . . . .30

Program Playback with Audio CD and

MP3/WMA file . . . . . . . . . . . . . . . . . . . . . . . . . .31 Viewing a JPEG File . . . . . . . . . . . . . . . . . .32-33 Editing a MP3/WMA, JPEG, DivX file . . . . . .34-35

Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . .36-42

About DVD recording . . . . . . . . . . . . . . . . . . . .36 About HDD recording . . . . . . . . . . . . . . . . . . . .36 Timeshift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37 Basic Recording from a TV . . . . . . . . . . . . . . . .38 Instant Timer Recording . . . . . . . . . . . . . . . . . .38 Timer Recording . . . . . . . . . . . . . . . . . . . . . . . .39 Checking Timer Recording Details . . . . . . . . . .40 Recording from an External Input . . . . . . . . . . .40 Recording from DV Input . . . . . . . . . . . . . . . . .41 Simultaneous recording and playback . . . . . . . .42

Playback another title during recording . . . .42 Time Slip . . . . . . . . . . . . . . . . . . . . . . . . . . .42 MPEG4 Recording . . . . . . . . . . . . . . . . . . . . . .42

Editing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	43-50
Title List and Chapter List Menu Overview . . . .43
HDD, VR Mode: Original and Playlist Editing	. . .44
Adding Chapter Markers . . . . . . . . . . . . . . .	. .44
Changing the Title Thumbnails . . . . . . . . . .	. . .44
Making a New Playlist . . . . . . . . . . . . . . . . . .	. .45
Adding Additional Title/Chapters to the Playlist .45
Deleting an Original or Playlist Title/Chapter	. . .46
Deleting a Part . . . . . . . . . . . . . . . . . . . . . . .	. .46
Naming a Title . . . . . . . . . . . . . . . . . . . . . . .	. .47
Time Search . . . . . . . . . . . . . . . . . . . . . . .	. . .47
Sorting the title list . . . . . . . . . . . . . . . . . . . .	. .48
Combining Two Titles Into One . . . . . . . . . . .	. .48
Divide One Titles Into Two . . . . . . . . . . . . . .	. .48
Combining Two Chapters Into One . . . . . . .	. . .49
Additional functions for the recordable
DVD discs . . . . . . . . . . . . . . . . . . . . . . . . . .	. .49
Moving a Playlist Chapter . . . . . . . . . . . . . . .	. .50
Hide a Chapter/Title . . . . . . . . . . . . . . . . . . .	. .50
Protect a Title . . . . . . . . . . . . . . . . . . . . . . . .	. .50

Dubbing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51-53

Before Dubbing . . . . . . . . . . . . . . . . . . . . . . . . .51 Dubbing from HDD to DVD . . . . . . . . . . . . . . .52 Dubbing from DVD to HDD . . . . . . . . . . . . . . . .52 One Touch Copy (HDD to DVD) . . . . . . . . . . . .53 One Touch Copy (DVD to HDD) . . . . . . . . . . . .53

Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . .54-59

Additional Information . . . . . . . . . . . . . . . . . . . .54 Overwriting Recording . . . . . . . . . . . . . . . . .54 Viewing Title List menu displayed on other DVD Recorders or Players . . . . . . . . . . . . .54 Playing Your Recordings on Other DVD Players (Finalizing a Disc) . . . . . . . . . . . . . .54

Language Codes . . . . . . . . . . . . . . . . . . . . . . .55 Area Codes . . . . . . . . . . . . . . . . . . . . . . . . . . .55 Controlling Your TV with the Supplied

Remote Control . . . . . . . . . . . . . . . . . . . . . . . .56 Troubleshooting . . . . . . . . . . . . . . . . . . . . . .57-58 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . .59

4

Introduction

To ensure proper use of this product, please read this owner’s manual carefully and retain for future reference.

This manual provides information on the operation and maintenance of your recorder. Should the unit require service, contact an authorized service location.

Notes on Discs

Handling Discs

Do not touch the playback side of the disc. Hold the disc by the edges so that fingerprints do not get on the surface. Never stick paper or tape on the disc.

About the Symbol Display

“ ” may appear on your TV display during operation and indicates that the function explained in this owner’s manual is not available on that specific media.

Symbol Used in this Manual

Note:

Indicates special notes and operating features.

Tip:

Indicates tips and hints for making the task easier.

A section whose title has one of the following symbols are applicable only to the disc represented by the symbol.

HDD Titles recorded on the HDD

DVD ALL All DVD discs listed below.

RAM DVD-RAM disc

-RWVR DVD-RW with VR recording mode

-RWVideo DVD-RW with Video recording mode

+RW DVD+RW disc

-R DVD-R disc

+R DVD+R (DL) disc

DVD DVD-Video disc

Storing Discs

After playing, store the disc in its case. Do not expose the disc to direct sunlight or sources of heat and never leave it in a parked car exposed to direct sunlight.

Cleaning Discs

Fingerprints and dust on the disc can cause poor picture quality and sound distortion. Before playing, clean the disc with a clean cloth. Wipe the disc from the center out.

Do not use strong solvents such as alcohol, benzine, thinner, commercially available cleaners, or anti-static spray intended for older vinyl records.

VCD Video CDs

ACD Audio CDs

DivX DivX files

MP3 MP3 files

WMA WMA files

JPEG JPEG files

What is SIMPLINK?

Moisture Condensation

Never operate this product immediately after moving it from a cold location to a warm location. Leave it for two or three hours without operating it. If you use this product in such a situation, it may damage discs and internal parts.

Some functions of this unit are controlled by TV’s remote control when this unit and LG TV with SIMPLINK are connected through HDMI connection.

•Controllable functions by LG TV’s remote control; Play, Pause, Scan, Skip, Stop, Power Off, etc.

•Refer to the TV owner’s manual for the details of SIMPLINK function.

•LG TV with SIMPLINK function has the logo as shown above.

<![if ! IE]>

<![endif]>Introduction

5

Recordable and Playable Discs

DVD-RW (Digital Video Disc - ReWritable):

DVD-RW discs can be formatted for VR mode recording or Video mode recording.

These Discs can be recorded on repeatedly. Recordings can be erased, then you can record again on the same Disc.

[VR mode]

Recordings can be extensively edited

Playable only on VR mode compatible players (after finalization) [Video mode]

Playable on regular DVD players (after finalization)

Limited editing features

DVD-R (Digital Video Disc - Recordable)

These Discs can be recorded only once. After you finalize a DVD-R, you cannot record on it or edit it.

DVD-R discs can be only formatted to Video mode.

Playable on regular DVD players (after finalization)

Limited editing features

DVD-RAM (DVD - Random Access Memory)

DVD-RAM discs can be formatted for VR mode recording.

These Discs can be recorded on repeatedly. Recordings can be erased, then you can record again on the same Disc.

Playable on DVD-RAM compatible players.

Recordings can be extensively edited.

Only DVD-RAM standard Version 2.0, 2.1 and 2.2 discs can be used in this unit.

You cannot use the cartridge-type DVD-RAM disc in this unit.

DVD+RW (Digital Video Disc + ReWritable)

These Discs can be recorded on repeatedly. Recordings can be erased, then you can record again on the same Disc.

Playable on DVD+RW compatible players (automatically finalization)

The edited contents are playable on DVD+RW compatible players only after finalization

Recordings can be edited the title/chapter

DVD+R (Digital Video Disc + Recordable)

These Discs can be recorded only once. After you finalize a DVD+R, you cannot record on it or edit it any more.

Playable on DVD+R compatible players (after finalization)

Any edited contents are not be compatible on DVD+R compatible players. (Hide, chapter combine, added chapter mark, etc.)

Limited title/chapter editing features.

DVD+R DL (Digital Video Disc + Recordable; Double Layer)

These Discs can be recorded only once. After you finalize a DVD+R DL, you cannot record on it or edit it any more.

Storage space is nearly doubled with double layer DVD+R media, allowing consumers to record up to 8.5GB of video on a single DVD+R disc.

Playable on DVD+R DL compatible players (after finalization)

Any edited contents are not be compatible on DVD+R DL compatible players. (Hide, chapter combine, added chapter mark, etc.)

Limited title/chapter editing features.

Recommended recordable DVD discs

DVD-R	DVD+R	DVD-RW	DVD+RW	DVD+R(DL)	DVD-RAM
Mitsubishi (8x, 16x)	Mitsubishi (8x, 16x)	Mitsubishi (4x)	Mitsubishi (4x)	Mitsubishi (2,4x)	Fujifilm (2x)
That’s (8x, 16x)	Ricoh (8x, 16x)	Verbatim (4x)	SONY (2.4x)	Maxell (2,4x)	Mitsubishi (3x)
SONY (16x)	SONY (16x)	JVC (4x)	Verbatim (2.4x)	-	-
-	-	Victor (4x)	Ricoh (2.4x, 4x)	-	-
-	-	Maxell (4x)	-	-	-

6

Playable Discs

DVD (8 cm / 12 cm disc)

Discs such as movies that can be purchased or rented

Video CD (VCD) (8 cm / 12 cm disc)

VIDEO CDs or CD-Rs/CD-RWs in VIDEO CD/Super VIDEO CD format

Audio CD (8 cm / 12 cm disc)

Music CDs or CD-Rs/CD-RWs in music CD format that can be purchased

CD-R/CD-RW (8 cm / 12 cm disc)

CD-R/CD-RW discs that contain audio titles, DivX, MP3, WMA, or JPEG files.

Notes:

Depending on the conditions of the recording equipment or the CD-R/RW (or DVD±R/RW) disc itself, some CD-R/RW (or DVD±R/RW) discs cannot be played on the unit.

Do not attach any seal or label to either side (the labeled side or the recorded side) of a disc.

Do not use irregularly shaped CDs (e.g., heart-shaped or octagonal). Doing so may result in malfunctions.

Depending on the recording software & the finalization, some recorded discs (CD-R/RW or DVD±R/RW) may not be playable.

DVD-R/RW, DVD+R/RW and CD-R/RW discs recorded using a personal computer or a DVD or CD Recorder may not play if the disc is damaged or dirty, or if there is dirt or condensation on the Recorder’s lens.

If you record a disc using a personal computer, even if it is recorded in a compatible format, there are cases in which it may not play because of the settings of the application software used to create the disc. (Check with the software publisher for more detailed information.)

This recorder requires discs and recordings to meet certain technical standards in order to achieve optimal playback quality. Pre-recorded DVDs are automatically set to these standards. There are many different types of recordable disc formats (including CD-R containing MP3 or WMA files) and these require certain preexisting conditions (see above) to ensure compatible playback.

Customers should note that permission is required in order to download MP3 / WMA files and music from the Internet. Our company has no right to grant such permission. Permission should always be sought from the copyright owner.

Regional Code

This unit has a regional code printed on the rear of the unit. This unit can play only DVD discs labeled same as the rear of the unit or “ALL”.

Notes on Regional Codes

Most DVD discs have a globe with one or more numbers in it clearly visible on the cover. This number must match your unit’s regional code or the disc cannot play.

If you try to play a DVD with a different regional code from the unit, the message “Incorrect region code. Can’t play back” appears on the TV screen.

Availability of copying or moving feature

From	To	MP3/WMA	JPEG	DivX	Audio CD	Video CD	Title*1
HDD	DISC	No	No	No	No	No	Yes
HDD	USB Memory	No	No	No	No	No	No
DISC	HDD	Yes	Yes	Yes	No	No	Yes
DISC	USB Memory	No	No	No	No	No	No
USB Memory	HDD	Yes	Yes	Yes	No	No	No
USB Memory	DISC	No	No	No	No	No	No

*1 The title is recorded from this unit.

<![if ! IE]>

<![endif]>Introduction

7

About the internal hard disk drive

The internal hard disk drive (HDD) is a fragile piece of equipment. Please use the recorder following the guidelines below to protect against possible HDD failure.

We recommend that you back up your important recordings onto DVD discs in order to protect against accidental loss.

Do not move the recorder while it is on.

Install and use the recorder on a stable, level surface.

Do not block the rear vent/cooling fan.

Do not use the recorder in excessively hot or humid places, or in places that may be subject to sudden changes in temperature. Sudden changes in temperature can cause condensation to form inside the recorder. This can be a cause of HDD failure.

While the recorder is switched on, do not unplug from the wall socket or switch the electricity off from the breaker switch.

Do not move the recorder immediately after switching it off. If you need to move the recorder, please follow the steps below:

1.After the message POWER OFF is shown in the display, wait at least two minutes.

2.Unplug from the wall socket.

3.Move the recorder.

If there’s a power failure while the recorder is on there is a chance that some data on the HDD will be lost.

The HDD is very delicate. If used improperly or in an unsuitable environment, it is possible that the HDD will fail after a few years of use. Signs of problems include playback unexpectedly freezing and noticeable block noise (mosaic) in the picture. However, sometimes there will be no warning signs of HDD failure.

If the HDD fails, no playback of recorded material will be possible. In this case it will be necessary to replace the HDD unit.

Using an USB Memory Stick

This unit can play the MP3 / WMA / JPEG files contained in the USB Memory Stick.

Inserting/Removing the USB Memory

Stick

Inserting the USB Memory Stick

Insert straight-in until it fits into place.

Removing the USB Memory Stick

Withdraw the USB Memory Stick carefully.

Notes:

Keep the USB Memory Stick out of reach of children. If swallowed, seek medical advice immediately.

This unit supports only USB Flash Memory with FAT16 or FAT32 format.

The USB Memory Sticks which require additional program installation when you have connected it to a computer are not supported.

This unit is compatible with the Flash type USB Memory Stick that supports USB 1.1.

This unit may not supports some USB Memory Stick.

Do not extract the USB Memory Stick in operating (play, copy, etc.). It may cause a malfunction of this unit.

Using the USB Memory Stick

1.Insert an USB Memory Stick.

2.Press HOME on the remote control.

3.Select [MUSIC], [PHOTO] or [MOVIE] option.

4.Select [USB] then press ENTER. Details for the options are on page 17.

8

Front Panel

a

b

c

d e f g h i j k

a 1 POWER

Switches the recorder ON or OFF.

b Disc Tray

Insert a disc here.

c Display window

Shows the current status of the recorder.

T/S: Indicates the timeshifting mode.

REC: The recorder is recording.

HDD: The recorder is HDD mode.

DVD: The recorder is DVD mode.

HDD b B DVD: The recorder is dubbing.

TV: Indicates when the recorder is in TV tuner mode.

: Indicates when the recorder is in timer recording or a timer recording is programmed.

: Indicates clock, total playing time, elapsed time, title number, chapter/track number, channel, etc.

d Remote Sensor

Point the recorder remote control here.

e OPEN/CLOSE (Z)

Opens or closes the disc tray.

fHDD/DVD

Set the recorder’s mode to HDD or DVD.

l m n

gRESOLUTION

Sets the output resolution for HDMI and COMPONENT OUTPUT jacks.

-HDMI: 480i, 480p, 720p, 1080i

-COMPONENT: 480i, 480p

hN / X (PLAY / PAUSE)

Starts playback.

Pause playback or recording temporarily, press again to exit pause mode.

ix (STOP)

Stops playback or recording.

jz (REC)

Starts recording. Press repeatedly to set the recording time.

kCH (V/v)

Scans up or down through memorized channels.

lUSB Port

Connect an USB Memory Stick.

mDV IN

Connect the DV output of a digital camcorder.

nAV IN 2 (VIDEO IN/AUDIO IN (Left/Right))

Connect the audio/video output of an external source (Audio system, TV/ Monitor, VCR, Camcorder, etc.).

	Touch Pad Operation	Precautions in using the touch pad
		The LEDs on the touch pad lights only when the
	The buttons from e to k are touch pad type button
		power of the unit is on.
	that is operated with brief touch.
		Use the touch pad with clean and dry hands.
	When you operate the button on the touch pad, you	Do not press the button on the touch pad with too
	should follow the directions as below.	much force.
	1. Touch the any button on the touch pad.	Do not touch the button on the touch pad with any
	The LEDs on the touch pad light up.	conductive material such as metalic object.
	2. Touch the button you want to operate.	It may cause a malfunction.
	The LEDs on the touch pad will be off in 10
	seconds after the operation.

<![if ! IE]>

<![endif]>Introduction

9

Remote Control

a

AV/INPUT: Changes the input to use for recording (Tuner, AV1-2, or DV IN).

0-9 numerical buttons: Selects numbered options in a menu. DUBBING: Copies DVD to HDD (or HDD to DVD).

PIP: Selects PIP function on or off.

TV Control Buttons: See page 56.

b

	AUDIO ( ): Selects an audio
b	language or audio channel.
	SUBTITLE ( ): Selects a subtitle
	language.
c	CHP. ADD: Inserts a chapter
	marker when playing.
	REC (z): Starts recording.
	REC MODE: Selects the recording
	mode.
d	TITLE: Displays the disc’s Title
	menu, if available.

e

a

POWER: Switches the recorder ON or OFF.

OPEN/CLOSE (Z): Opens and closes the disc tray.

DVD: Selects the unit’s function mode to DVD.

HDD: Selects the unit’s function mode to HDD.

c

SCAN (m / M): Search backward or forward.

SKIP (. / >): Go to next or previous chapter or track.

PAUSE/STEP (X) : Pause playback or recording temporarily.

PLAY (N): Starts playback.

STOP (x): Stops playback or recording.

d

HOME: Accesses or removes the HOME menu.

MENU/LIST: Accesses menu on a DVD disc. Switches between Title List-Original and Title List-Playlist menu.

b / B / v / V (left/right/up/down):

Selects an option in the menu.

ENTER (): Acknowledges menu selection.

PR/CH (+/-): Scans up or down through memorized channels. DISPLAY: Accesses On-Screen Display.

RETURN (O): Removes the menu.

e

TIMESHIFT: Activates pause live TV/playback (timeshift) for a live TV program.

MARKER: Marks any point during playback.

SEARCH: Displays Marker Search menu.

CLEAR: Removes a track number on the Program List or a mark on the Marker Search menu.

ZOOM: Enlarges video image. REPEAT: Repeat chapter, track, title, all.

A-B: Repeat sequence. THUMBNAIL: Selects a thumbnail picture.

TV/DVD: To view channels selected by the recorder tuner or by the TV tuner.

Remote Control Operation

Point the Remote Control at the remote sensor and press the buttons.

Caution

Do not mix old and new batteries. Never mix different types of batteries (standard, alkaline, etc.).

Remote Control Battery Installation

Remove the battery cover on the rear of the Remote Control, and insert two R03 (size AAA) batteries with and matched correctly.

10

Hookup and Settings

Rear Panel

a

b

c

d

e

f

g h i j k

l

aANTENNA IN

Connect the antenna to this terminal.

bCOMPONENT OUTPUT (Y PB PR)

Connect to a TV with Y PB PR inputs.

cINPUT 1 (VIDEO IN/AUDIO IN (Left/Right))

Connect the audio/video output of an external source (Audio system, TV/ Monitor, VCR, Camcorder, etc.).

dHDMI OUTPUT (Type A)

HDMI output providing a high quality interface for digital audio and video.

eCooling fan

fAC Power Cord

Plug into the power source.

gANTENNA OUT

Passes the signal from the ANTENNA IN jack to your TV/monitor.

h OPTICAL (Digital audio output jack)

Connect to digital (optical) audio equipment.

i COAXIAL (Digital audio output jack)

Connect to digital (coaxial) audio equipment.

j S-VIDEO OUTPUT

Connect to a S-Video Input on TV.

k AUDIO OUTPUT (Left/Right)

Connect to a TV with audio inputs.

l VIDEO/AUDIO OUT (VIDEO / AUDIO OUT (Left/Right))

Connect to a TV with video/audio inputs.

<![if ! IE]>

<![endif]>Settings

<![if ! IE]>

<![endif]>Hookup and

11

Connecting an Antenna or Cable TV

a Antenna:

Disconnect the antenna from the rear of the TV and identify the antenna cable. If it is a round 75 ohm coaxial cable connect it directly to the jack marked ANT. IN on your Recorder. If your antenna cable is flat connect it to a 300-ohm to 75-ohm antenna

adaptor (not supplied) and slip the adaptor over the ANT. IN jack. Don’t attempt to screw it into to the Recorder.

b Cable TV:

If your cable connection has no converter or descrambler, unscrew the cable from your TV and attach it to the ANT. IN jack on the Recorder.

If a converter is required connect a coaxial cable from the wall jack to the IN connector on the converter, and a coaxial cable from the OUT connector on the converter to the ANT. IN on your Recorder. This cable hookup permits both TV and Recorder operation.

To view or record a CATV channel

1.Tune the TV to the Recorder output channel (CH 3 or 4).

2.Set the Recorder channel selector to the cable output channel. (Example: CH3)

3.Select a channel using the cable converter.

Notes:

•With this connection, you cannot record one channel while viewing another.

•If you are using a cable box to tune channels, it is not necessary to do Auto Channel Set.

a	Antenna	Antenna
		Cable TV
		Wall Jack
	Flat Wire
	(300 ohm)
	300/75 ohm OR	OR
	Adapter
	(Not supplied)

Rear of the recorder

b

Cable TV

Back Panel of Wall Jack

Typical Cable Box

12

Connections to Your TV

Make one of the following connections, depending on the capabilities of your existing equipment.

Tips

Depending on your TV and other equipment you wish to connect, there are various ways you could connect the recorder. Use only one of the connections described below.

Please refer to the manuals of your TV, VCR, Stereo System or other devices as necessary to make the best connections.

Caution

–Make sure the recorder is connected directly to the TV. Tune the TV to the correct video input channel.

–Do not connect the recorder’s AUDIO OUTPUT jack to the phono in jack (record deck) of your audio system.

–Do not connect your recorder via your VCR. The DVD image could be distorted by the copy protection system.

RF coaxial connection

Connect the RF OUT jack on the Recorder to the antenna in jack on the TV using the supplied 75-ohm Coaxial Cable (R).

How to set the Recorder’s RF output channel

1.When the Recorder is turned off, press and hold CH (V/v) on the front panel for more than five seconds. [ch03] or [ch04] appears in the display window.

2.Press CH (V/v) to change the RF output channel (ch03 or ch04).

3.Tune the TV to this channel.

Video connection

Connect the VIDEO OUTPUT jack on the recorder to the video in jack on the TV using the video cable (V).

Audio (Left/Right) Connection

Connect the left and right AUDIO OUTPUT jacks of the recorder to the audio left and right IN jacks on the TV using the audio cables (A). Do not connect the recorder’s AUDIO OUTPUT jack to the phono in jack (record deck) of your audio system.

S-Video connection

Connect the S-VIDEO OUTPUT jack on the recorder to the S-Video in jack on the TV using the S-Video cable (S).

Component Video connection

Connect the COMPONENT OUTPUT jacks on the recorder to the corresponding input jacks on the TV using an Y Pb Pr cable (C).

If your television is a high-definition or “digital ready” television, you may take advantage of the recorder’s progressive scan output for the highest video resolution possible. If your TV does not accept the Progressive Scan format, the picture will appear scrambled if you try Progressive Scan on the recorder.

Set the resolution to 480p using RES. button for progressive signal.

Note:

Progressive scan does not work with the analog video connections (yellow VIDEO OUTPUT jack) or S-VIDEO connection.

Caution

If the resolution is set to 720p or 1080i, the VIDEO OUTPUT, S-VIDEO OUTPUT and COMPONENT OUTPUT connections are not available.

<![if ! IE]>

<![endif]>Settings

<![if ! IE]>

<![endif]>Hookup and

13

HDMI connection

If you have a HDMI TV or monitor, you can connect it to this recorder using a HDMI cable.

1.Connect the HDMI OUTPUT jack on the recorder to the HDMI INPUT jack on a HDMI compatible TV or monitor (H).

2.Set the TV’s source to HDMI (refer to TV’s Owner’s manual).

Notes:

If your TV is NOT capable of handling 96 kHz sampling frequency, set the [Sampling Freq.] option to [48 kHz] on the setup menu (See page 20). When this choice is made, this unit will automatically convert any 96 kHz signals to 48 kHz so your system can decode them.

If your TV is not equipped with Dolby Digital and MPEG decoder, set the [Dolby Digital] and [MPEG] options to [PCM] on the setup menu (See page 20).

If your TV is not equipped with DTS decoder, set the [DTS] options to [OFF] on the setup menu (See page 20). To enjoy DTS multi channel surround, you must connect this recorder to a DTS compatible receiver via one of this recorder’s digital audio outputs.

The arrow on the cable connector body should face up for correct alignment with the connector on the recorder.

(Type A)

If there is noise or lines on the screen, please check the HDMI cable.

Tip :

When you use HDMI connection, you can change the resolution (480i, 480p, 720p, or 1080i) for the HDMI output using RES. button.

Caution

Changing the resolution when the recorder is connected with HDMI connector may result in malfunctions. To solve the problem, turn off the recorder and then turn it on again.

About HDMI

HDMI (High Definition Multimedia Interface) supports both video and audio on a single digital connection for use with DVD Players, Set-Top Boxes, and other AV devices.

HDMI was developed to provide the technologies of HDCP (High Definition Contents Protection). HDCP is used to protect digital content transmitted and received.

HDMI has the capability to support standard, enhanced, or high-definition video plus standard to multi-channel surround-sound audio, HDMI features include uncompressed digital video, a bandwidth of up to 5 gigabytes per second, one connector (instead of several cables and connectors), and communication between the AV source and AV devices such as DTVs.

HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI licensing LLC.

Additional Information for HDMI

When you connect a HDMI or DVI compatible device make sure of the followings:

-Try switching off the HDMI/DVI device and this recorder. Next, switch on the HDMI/DVI device and leave it for around 30 seconds, then switch on this recorder.

-The connected device’s video input is set correctly for this unit.

-The connected device is compatible with 720(1440)x480i, 720x480p, 1280x720p, or 1920x1080i video input.

Not all HDCP-compatible DVI devices will work with this recorder.

-The picture will not be displayed properly with non-HDCP device.

14

Connecting to an Amplifier

Connecting to an amplifier equipped with two channel analog stereo or Dolby Pro Logic ll/ Pro Logic

Connect the Left and Right AUDIO OUTPUT jacks on the recorder to the audio left and right in jacks on your amplifier, receiver, or stereo system, using the audio cables (A).

Connecting to an amplifier equipped with two channel digital stereo (PCM) or to an Audio/ Video receiver equipped with a multi-channel decoder (Dolby Digital™, MPEG 2, or DTS)

1.Connect one of the recorder’s DIGITAL AUDIO OUTPUT jacks (OPTICAL O or COAXIAL X) to the corresponding in jack on your amplifier. Use an optional digital (optical O or coaxial X) audio cable.

2.You will need to activate the recorder’s digital output. (See “Audio Settings” on page 20).

Digital Multi-channel sound

A digital multi-channel connection provides the best sound quality. For this you need a multi-channel Audio/Video receiver that supports one or more of the audio formats supported by your recorder (MPEG 2, Dolby Digital and DTS). Check the receiver manual and the logos on the front of the receiver.

Caution:

Due to the DTS Licensing agreement, the digital output will be in DTS digital out when DTS audio stream is selected.

Notes:

–If the audio format of the digital output does not match the capabilities of your receiver, the receiver will produce a strong, distorted sound or no sound at all.

–Six Channel Digital Surround Sound via digital connection can only be obtained if your receiver is equipped with a Digital Multi-channel decoder.

–To see the audio format of the current DVD in the on-screen display, press AUDIO.

–This recorder does not perform internal (2 channel) decoding of a DTS sound track. To enjoy DTS multi channel surround, you must connect this recorder to a DTS compatible receiver via one of this recorder’s digital audio outputs.

Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic”, and the double- D symbol are trademarks of Dolby Laboratories.

“DTS” and “DTS Digital Out” are trademarks of Digital Theater Systems, Inc.

<![if ! IE]>

<![endif]>Settings

<![if ! IE]>

<![endif]>Hookup and

15

Accessory Audio/Video (A/V)

Connections

Connecting to the AV IN 1 or AV IN 2 Jacks

Connect the input jacks (AV IN 1, AV IN 2) on the recorder to the audio/video out jacks on your accessory component, using audio/video cables.

Jack panel of Accessory Component (VCR, Camcorder, etc.)

AUDIO

OUTPUT

R

L

VIDEO

OUTPUT

Connecting a Digital Camcorder

Using the front panel DV IN jack, it is possible to connect a DV digital camcorder and digitally transfer DV tapes to DVD.

Use a DV cable (not supplied) to connect the DV in/out jack of your DV camcorder to the front panel DV IN jack of this recorder.

Notes:

This jack is for connection to DV digital camcorder only. It is not compatible with digital satellite tuners or D-VHS video decks.

Disconnecting the DV cable while recording a contents of the connected digital camcorder may result in malfunction.

DV Digital Camcorder

DV

IN/OUT

	Rear of	Front of
	the recorder
		the recorder

Front of the recorder

16

Auto Set Up

After the POWER is pressed for the first time to turn on the unit or resetting the unit, the Initial Setup Wizard function sets the language, clock and tuner channels automatically.

1.Select a language for the Setup menu and onscreen display. Use v / V to select a language then press ENTER.

2.Prese check your antenna connections. Press ENTER to move next step.

3.Use v / V to select the Clock Set option then press ENTER.

[Auto]

1)Use v / V / b / B to choose Band, PBS channel, Time Zone, Daylight Savings options. (Details are on page 19)

2)Press ENTER to confirm your setting.

[Manual]:

1)Enter the necessary information for date and time.

b / B (left/right): Moves the cursor to the previous or next column.

v / V (up/down): Changes the setting at the current cursor position.

2)Press ENTER to confirm your setting.

4.Please ENTER while [Start] option is selected. The tuner will automatically cycle through all available channels in the area and place them in the tuner’s memory.

5.Press ENTER to finish setup.

Using the Home Menu

From the Home Menu screen you can access all the Media for playback and recording of the recorder.

1.Press HOME to display the Home Menu screen.

2.Use the b / B buttons to select a main option you want. Sub options appears.

3.Use the v / V and ENTER buttons to select the sub option you want.

4. To exit the HOME menu, press HOME.

TV

TV HDD: Returns to live TV viewing in HDD mode. Pressing the HDD button on the remote control will also allow you to directly choose this option.

TV DVD: Returns to live TV viewing in DVD mode. Pressing the DVD button on the remote control will also allow you to directly choose this option.

MOVIE

HDD: Displays the Title List menu for HDD. (page 43)

HDD DivX: Displays the [Movie List] menu for HDD. (page 29)

DISC:

-Displays Title List menu for recordable disc (page 43)

-Displays [Movie List] menu for DivX disc. (page 29)

-Plays back Video CD or DVD-Video disc (page 25-28).

USB: Displays [Movie List] menu for the USB Memory Stick. (page 29)

PHOTO (See page 32)

HDD: Displays [Photo List] menu for HDD.

DISC: Displays [Photo List] menu for disc.

USB: Displays [Photo List] menu for the USB Memory Stick.

MUSIC (See page 30)

HDD: Displays [Music List] menu for HDD.

DISC: Displays Music (or Audio CD) menu for disc.

USB: Displays [Music List] menu for the USB Memory Stick.

Easy Menu (See page 17)

SETUP: Displays Setup menu.

Timer Record: Displays Timer Record menu.

<![if ! IE]>

<![endif]>Settings

<![if ! IE]>

<![endif]>Hookup and

17

Initial Settings

In this menu system, there are several ways to customize the settings provided. Most menus consist of three levels to set up the options, but some require greater depth for the variety of settings.

General Operation

1.Select the SETUP option in the HOME menu. The setup menu appears.

2.Use v / V to select the desired option.

3.While the desired item is selected, press B to move to the second level.

4.Use v / V to select the second desired option.

5.Press B to move to the third level.

6.Use v / V to select the desired setting then press ENTER to confirm your selection.

Some items require additional steps.

7.Press RETURN to exit the Setup menu.

Note:

Press b to go back to the previous level.

General Settings

Tuning Band Select

1.Select the [Tuning Band] option then press B .

2.Use v / V to select the tuning band (TV or CATV) option then press ENTER.

TV: If you are using a standard antenna to receive channels.

CATV: If you are using basic cable to receive channels.

Auto Channel Set

Connect the Recorder to the desired type of antenna or cable TV system as shown on page 12.

This Recorder is equipped with a frequency synthesized tuner capable of receiving up to 181 channels. These include VHF channels 2-13, UHF channels 14-69 and CATV channels 1-125.

1.Select the [Auto Channel Set] option.

2.Press B to move to the third level. [Start] icon is highlighted.

3.Press ENTER to begin the channel search. The tuner will automatically cycle through all

available channels in the area and place them in the tuner’s memory.

Note:

After the Auto Channel Set proceeding is complete, make sure the Tuning Band is set appropriately (TV or CATV) on tuning band, follow steps 1~2 as shown previous (Tuning Band Select) to choose the correct Tuning Band (TV or CATV).

To Add or Erase Channels

This feature allows you to add to or erase channels from memory manually.

1.Select the [CH. Add/Del] option.

2.Press B to move to the third level. [Edit] icon is highlighted.

3.Press ENTER and the Channel Edit menu appears.

4.Use v / V or number buttons to select a channel then press B.

5.If you want to obtain a clearer picture, tune the [MFT] option using v / V then press B.

[Add] or [Delete] icon is highlighted.

6.Press ENTER to confirm your setting.

7.Repeat steps 4-6 to add or erase additional channels.

8.Press RETURN (O) to exit the menu.

18