LG OLED55B6, OLED65B6 Schematic

Internal Use Only

OLED TV

SERVICE MANUAL

CHASSIS : ED64B

MODEL : OLED55/65B6* OLED55/65B6*-Z

CAUTION

BEFORE SERVICING THE CHASSIS, READ THE SAFETY PRECAUTIONS IN THIS MANUAL.

P/NO : MFL69570101 (1604-REV00)

CONTENTS

CONTENTS .............................................................................................. 2

SAFETY PRECAUTIONS ........................................................................ 3

SERVICING PRECAUTIONS.................................................................... 4

SPECIFICATION ....................................................................................... 6

ADJUSTMENT INSTRUCTION .............................................................. 15

BLOCK DIAGRAM.................................................................................. 27

EXPLODED VIEW ................................................................................... 35

DISASSEMBLY ....................................................................................... 36

TROUBLE SHOOTING GUIDE ................................................ APPENDIX

Only for training and service purposes

- 2 -

SAFETY PRECAUTIONS

IMPORTANT SAFETY NOTICE

Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the Schematic Diagram and Exploded View. It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent Shock, Fire, or other Hazards. Do not modify the original design without permission of manufacturer.

General Guidance

An isolation Transformer should always be used during the servicing of a receiver whose chassis is not isolated from the AC power line. Use a transformer of adequate power rating as this protects the technician from accidents resulting in personal injury from electrical shocks.

It will also protect the receiver and it's components from being damaged by accidental shorts of the circuitry that may be inadvertently introduced during the service operation.

If any fuse (or Fusible Resistor) in this TV receiver is blown, replace it with the specified.

When replacing a high wattage resistor (Oxide Metal Film Resistor, over 1 W), keep the resistor 10 mm away from PCB.

Keep wires away from high voltage or high temperature parts.

Before returning the receiver to the customer,

always perform an AC leakage current check on the exposed metallic parts of the cabinet, such as antennas, terminals, etc., to be sure the set is safe to operate without damage of electrical shock.

Leakage Current Cold Check(Antenna Cold Check)

With the instrument AC plug removed from AC source, connect an electrical jumper across the two AC plug prongs. Place the AC switch in the on position, connect one lead of ohm-meter to the AC plug prongs tied together and touch other ohm-meter lead in turn to each exposed metallic parts such as antenna terminals, phone jacks, etc. If the exposed metallic part has a return path to the chassis, the measured resistance should be between 1 MΩ and 5.2 MΩ. When the exposed metal has no return path to the chassis the reading must be infinite. An other abnormality exists that must be corrected before the receiver is returned to the customer.

Leakage Current Hot Check (See below Figure)

Plug the AC cord directly into the AC outlet.

Do not use a line Isolation Transformer during this check. Connect 1.5 K / 10 watt resistor in parallel with a 0.15 uF capacitor between a known good earth ground (Water Pipe, Conduit, etc.) and the exposed metallic parts. Measure the AC voltage across the resistor using AC voltmeter with 1000 ohms/volt or more sensitivity. Reverse plug the AC cord into the AC outlet and repeat AC voltage measurements for each exposed metallic part. Any voltage measured must not exceed 0.75 volt RMS which is corresponds to

0.5 mA. In case any measurement is out of the limits specified, there is possibility of shock hazard and the set must be checked and repaired before it is returned to the customer.

Leakage Current Hot Check circuit

Only for training and service purposes

- 3 -

SERVICING PRECAUTIONS

CAUTION: Before servicing receivers covered by this service manual and its supplements and addenda, read and follow the

SAFETY PRECAUTIONS on page 3 of this publication. NOTE: If unforeseen circumstances create conict between the

following servicing precautions and any of the safety precautions on page 3 of this publication, always follow the safety precautions. Remember: Safety First.

General Servicing Precautions

1. Always unplug the receiver AC power cord from the AC power source before;

a. Removing or reinstalling any component, circuit board

module or any other receiver assembly.

b. Disconnecting or reconnecting any receiver electrical plug

or other electrical connection.

c. Connecting a test substitute in parallel with an electrolytic

capacitor in the receiver. CAUTION: A wrong part substitution or incorrect polarity installation of electrolytic capacitors may result in an explosion hazard.

2. Test high voltage only by measuring it with an appropriate high voltage meter or other voltage measuring device (DVM, FETVOM, etc) equipped with a suitable high voltage probe. Do not test high voltage by "drawing an arc".

3. Do not spray chemicals on or near this receiver or any of its assemblies.

4. Unless specied otherwise in this service manual, clean

electrical contacts only by applying the following mixture to the contacts with a pipe cleaner, cotton-tipped stick or comparable non-abrasive applicator; 10 % (by volume) Acetone and 90 % (by volume) isopropyl alcohol (90 % - 99 % strength)

CAUTION: This is a ammable mixture. Unless specied otherwise in this service manual, lubrication

of contacts in not required.

5. Do not defeat any plug/socket B+ voltage interlocks with which receivers covered by this service manual might be equipped.

6. Do not apply AC power to this instrument and/or any of its electrical assemblies unless all solid-state device heat sinks are correctly installed.

7. Always connect the test receiver ground lead to the receiver chassis ground before connecting the test receiver positive lead. Always remove the test receiver ground lead last.

8. Use with this receiver only the test xtures specied in this

service manual.

CAUTION: Do not connect the test xture ground strap to any

heat sink in this receiver.

Electrostatically Sensitive (ES) Devices

Some semiconductor (solid-state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES

devices are integrated circuits and some eld-effect transistors

and semiconductor “chip” components. The following techniques should be used to help reduce the incidence of component damage caused by static by static electricity.

1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging wrist strap device, which should be removed to prevent potential shock reasons prior to applying power to the unit under test.

2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly.

3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.

4. Use only an anti-static type solder removal device. Some sol-

der removal devices not classied as “anti-static” can generate electrical charges sufcient to damage ES devices.

5. Do not use freon-propelled chemicals. These can generate

electrical charges sufcient to damage ES devices.

6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive material).

7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the chassis or circuit assembly into which the device will be installed. CAUTION: Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.

8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing together of your clothes fabric or the lifting of your

foot from a carpeted oor can generate static electricity sufcient to damage an ES device.)

General Soldering Guidelines

1. Use a grounded-tip, low-wattage soldering iron and appropriate tip size and shape that will maintain tip temperature within the range or 500 °F to 600 °F.

2. Use an appropriate gauge of RMA resin-core solder composed of 60 parts tin/40 parts lead.

3. Keep the soldering iron tip clean and well tinned.

4. Thoroughly clean the surfaces to be soldered. Use a mall wirebristle (0.5 inch, or 1.25 cm) brush with a metal handle. Do not use freon-propelled spray-on cleaners.

5. Use the following unsoldering technique

a. Allow the soldering iron tip to reach normal temperature.

(500 °F to 600 °F) b. Heat the component lead until the solder melts. c. Quickly draw the melted solder with an anti-static, suction-

type solder removal device or with solder braid.

CAUTION: Work quickly to avoid overheating the circuit

board printed foil.

6. Use the following soldering technique. a. Allow the soldering iron tip to reach a normal temperature

(500 °F to 600 °F)

b. First, hold the soldering iron tip and solder the strand

against the component lead until the solder melts.

c. Quickly move the soldering iron tip to the junction of the

component lead and the printed circuit foil, and hold it there only until the solder ows onto and around both the component lead and the foil. CAUTION: Work quickly to avoid overheating the circuit board printed foil.

d. Closely inspect the solder area and remove any excess or

splashed solder with a small wire-bristle brush.

Only for training and service purposes

- 4 -

IC Remove/Replacement

Some chassis circuit boards have slotted holes (oblong) through which the IC leads are inserted and then bent at against the circuit foil. When holes are the slotted type, the following technique should be used to remove and replace the IC. When working with boards using the familiar round hole, use the standard technique as outlined in paragraphs 5 and 6 above.

Removal

1. Desolder and straighten each IC lead in one operation by gently prying up on the lead with the soldering iron tip as the solder melts.

2. Draw away the melted solder with an anti-static suction-type solder removal device (or with solder braid) before removing the IC.

Replacement

1. Carefully insert the replacement IC in the circuit board.

2. Carefully bend each IC lead against the circuit foil pad and solder it.

3. Clean the soldered areas with a small wire-bristle brush. (It is not necessary to reapply acrylic coating to the areas).

"Small-Signal" Discrete Transistor Removal/Replacement

1. Remove the defective transistor by clipping its leads as close as possible to the component body.

2. Bend into a "U" shape the end of each of three leads remaining on the circuit board.

3. Bend into a "U" shape the replacement transistor leads.

4. Connect the replacement transistor leads to the corresponding leads extending from the circuit board and crimp the "U" with long nose pliers to insure metal to metal contact then solder each connection.

Power Output, Transistor Device Removal/Replacement

1. Heat and remove all solder from around the transistor leads.

2. Remove the heat sink mounting screw (if so equipped).

3. Carefully remove the transistor from the heat sink of the circuit board.

4. Insert new transistor in the circuit board.

5. Solder each transistor lead, and clip off excess lead.

6. Replace heat sink.

Diode Removal/Replacement

1. Remove defective diode by clipping its leads as close as possible to diode body.

2. Bend the two remaining leads perpendicular y to the circuit board.

3. Observing diode polarity, wrap each lead of the new diode around the corresponding lead on the circuit board.

4. Securely crimp each connection and solder it.

5. Inspect (on the circuit board copper side) the solder joints of the two "original" leads. If they are not shiny, reheat them and if necessary, apply additional solder.

3. Solder the connections. CAUTION: Maintain original spacing between the replaced component and adjacent components and the circuit board to prevent excessive component temperatures.

Circuit Board Foil Repair

Excessive heat applied to the copper foil of any printed circuit board will weaken the adhesive that bonds the foil to the circuit board causing the foil to separate from or "lift-off" the board. The following guidelines and procedures should be followed whenever this condition is encountered.

At IC Connections

To repair a defective copper pattern at IC connections use the following procedure to install a jumper wire on the copper pattern side of the circuit board. (Use this technique only on IC connections).

1. Carefully remove the damaged copper pattern with a sharp knife. (Remove only as much copper as absolutely necessary).

2. carefully scratch away the solder resist and acrylic coating (if used) from the end of the remaining copper pattern.

3. Bend a small "U" in one end of a small gauge jumper wire and carefully crimp it around the IC pin. Solder the IC connection.

4. Route the jumper wire along the path of the out-away copper pattern and let it overlap the previously scraped end of the good copper pattern. Solder the overlapped area and clip off any excess jumper wire.

At Other Connections

Use the following technique to repair the defective copper pattern at connections other than IC Pins. This technique involves the installation of a jumper wire on the component side of the circuit board.

1. Remove the defective copper pattern with a sharp knife. Remove at least 1/4 inch of copper, to ensure that a hazardous condition will not exist if the jumper wire opens.

2. Trace along the copper pattern from both sides of the pattern break and locate the nearest component that is directly connected to the affected copper pattern.

3. Connect insulated 20-gauge jumper wire from the lead of the nearest component on one side of the pattern break to the lead of the nearest component on the other side. Carefully crimp and solder the connections. CAUTION: Be sure the insulated jumper wire is dressed so the it does not touch components or sharp edges.

Fuse and Conventional Resistor Removal/Replacement

1. Clip each fuse or resistor lead at top of the circuit board hollow stake.

2. Securely crimp the leads of replacement component around notch at stake top.

Only for training and service purposes

- 5 -

SPECIFICATION

NOTE : Specifications and others are subject to change without notice for improvement

.

1. Application range

This specification is applied to the OLED TV used ED64B chassis.

2. Requirement for Test

Each part is tested as below without special notice.

1) Temperature: 25 °C ± 5 °C(77 °F ± 9 °F), CST: 40 °C ± 5 °C

2) Relative Humidity: 65 % ± 10 %

3) Power Voltage : Standard input voltage (AC 100-240 V~, 50/60 Hz) * Standard Voltage of each products is marked by models.

4) Specification and performance of each parts are followed

each drawing and specification by part number in accordance with BOM.

5) The receiver must be operated for about 20 minutes prior to

the adjustment.

3. Test method

1) Performance: LGE TV test method followed

2) Demanded other specification

- Safety : CE, IEC specification

- EMC : CE, IEC specification

- Wireless : Wireless HD Specification (Option)

4. Model General Specification

No. Item Specication Remarks

DTV & Analog (Total 37 countries)

DTV (MPEG2/4, DVB-T) : 26 countrie

Germany, Netherland, Switzerland, Hungary, Austria, Slovenia, Bulgaria, France, Spain, Belgium, Luxemburg, Greece, Czech, Turkey, Morocco, Ireland, Latvia, Estonia, Lithuania, Poland, Portugal, Romania, Albania, Bosnia, Slovakia, Belarus

1 Market EU/CIS(PAL Market-37Countries)

DTV (MPEG2/4, DVB-T2) :11 countries

UK(Ireland), Sweden, Denmark, Finland, Norway, Ukraine, Kazakhstan, Russia, Italy, Croatia, Serbia

DTV (MPEG2/4, DVB-C) : 37 countries

Germany, Netherland, Switzerland, Hungary, Austria, Slovenia, Bulgaria, France, Spain, Italy, Belgium, Russia, Luxemburg, Greece, Czech, Croatia, Turkey, Morocco, Ireland, Latvia, Estonia, Lithuania, Poland, Portugal, Romania, Albania, Bosnia, Serbia, Slovakia, Belarus, UK, Sweden, Denmark, Finland, Norway, Ukraine, Kazakhstan

DTV (MPEG2/4,DVB-S) : 37 countries

Germany, Netherland, Switzerland, Hungary, Austria, Slovenia, Bulgaria, France, Spain,Belgium, Luxemburg, Greece, Czech, Turkey, Morocco, Ireland, Latvia, Estonia, Lithuania, Poland, Portugal, Romania, Albania, Bosnia, Slovakia, Belarus, UK(Ireland), Sweden, Denmark, Finland, Norway, Ukraine, Kazakhstan,Russia, Italy, Croatia, Serbia

Supported satellite : 35 satellites

ABS1 75.0E, AMOS 4.0W, ASIASAT3S 105.5E, ASTRA 19.2E, ASTRA

23.5E, ASTRA 28.2E, ASTRA 4.8E, ATLANTIC BIRD2 8.0W, ATLANTIC BIRD3 5.0W, BADR 26.0E, DIRECTV-1R 56.0E, EUROBIRD 9A 9.0E, EUROBIRD3 33.0E, EUTELSAT 36 A/B 36.0E,EUTELSAT W2A 10.0E, EUTELSAT W3A 7.0E, EUTELSAT7WA 7.3WEUTELSAT 16.0E, EXPRESS AM1 40.0E, EXPRESS AM3 140.0E, EXPRESS AM33 96.5E, HELLASSAT 39.0E, HISPASAT 1CDE 30.0WHOTBIRD 13.0E, INTELSAT10&7 68.5E, INTELSAT15 85.2E, INTELSAT1R 50.0W, INTELSAT903 33.5W, INTELSAT904 60.0E, NILESAT 7.0W, NSS12 57.0E, THOR 0.8W, TURKSAT 42.0E,YAMAL201 90.0E, OTHER

Only for training and service purposes

- 6 -

No. Item Specication Remarks

2 Broadcasting system

3 Program coverage

4 Receiving system

(1)PAL/SECAM B/G/I/D/K, SECAM L/L’ (2)DVB-T/T2, C, S/S2

(1) Digital TV

- VHF, UHF

- C-Band, Ku-Band

(2) Analogue TV

-VHF : E2 to E12

-UHF : E21 to E69

-CATV : S1 to S20

-HYPER : S21 to S47

Analog : Upper Heterodyne Digital : COFDM, QAM

* For the manual, refer the below table. [ Table 4.1.1. ]

► DVB-T

- Guard Interval(Bitrate_Mbit/s) : 1/4, 1/8, 1/16, 1/32

- Modulation : Code Rate QPSK : 1/2, 2/3, 3/4, 5/6, 7/8 16-QAM : 1/2, 2/3, 3/4, 5/6, 7/8 64-QAM : 1/2, 2/3, 3/4, 5/6, 7/8

► DVB-T2

- Guard Interval(Bitrate_Mbit/s) 1/4, 1/8, 1/16, 1/32, 1/128, 19/128, 19/256,

- Modulation : Code Rate QPSK : 1/2, 2/5, 2/3, 3/4, 5/6 16-QAM : 1/2, 2/5, 2/3, 3/4, 5/6 64-QAM : 1/2, 2/5, 2/3, 3/4, 5/6 256-QAM : 1/2, 2/5, 2/3, 3/4, 5/6

► DVB-C

- Symbolrate : 4.0 Msymbols/s to 7.2 Msymbols/s

- Modulation : 16QAM, 64-QAM, 128-QAM and 256-QAM

5 Input Voltage AC 100-240 V~, 50/60Hz

4.1.1. Broadcast receiver specification for Manual

Table 4.1.1.

Digital TV Analogue TV

Satellite Terrestrial Cable Terrestrial / Cable

Television system DVB-S/S2* DVB-T

DVB-T2*

Channel coverage (Band) 950 ~ 2150 Mhz VHF III : 174 ~ 230 Mhz

UHF IV : 470 ~ 606 Mhz

UHF V : 606 ~ 862 Mhz

S Band II : 230 ~ 300 Mhz

S Band III : 300 ~ 470 Mhz

Maximum number of

storable programmes

External antenna

impedance

6,000 3,000

► DVB-S/S2

- symbol rate : DVB-S2 (8PSK / QPSK) : 2 ~ 45 Msymbol/s DVB-S (QPSK) : 2 ~ 45 Msymbol/s

- viterbi DVB-S mode : 1/2, 2/3, 3/4, 5/6, 7/8 DVB-S2 mode : 1/2, 2/3, 3/4, 3/5, 4/5, 5/6, 8/9, 9/10

DVB-C PAL/SECAM B/G, D/K, I,

SECAM L

46 ~862 Mhz 46 ~ 862 Mhz

75 Ω

Only for training and service purposes

- 7 -

5. External Input Format

5.1. 2D Mode

(1) Component (Y, CB/PB, CR/PR)

No. Resolution H-freq(kHz) V-freq(Hz) Pixel clock Proposed

1 720*480 15.73 60 13.5135 SDTV ,DVD 480I

2 720*480 15.73 59.94 13.5 SDTV ,DVD 480I

3 720*480 31.50 60 27.027 SDTV 480P

4 720*480 31.47 59.94 27.0 SDTV 480P

5 1280*720 45.00 60.00 74.25 HDTV 720P

6 1280*720 44.96 59.94 74.176 HDTV 720P

7 1920*1080 33.75 60.00 74.25 HDTV 1080I

8 1920*1080 33.72 59.94 74.176 HDTV 1080I

9 1920*1080 67.500 60 148.50 HDTV 1080P

10 1920*1080 67.432 59.94 148.352 HDTV 1080P

11 1920*1080 27.000 24.000 74.25 HDTV 1080P

12 1920*1080 26.97 23.976 74.176 HDTV 1080P

13 1920*1080 33.75 30.000 74.25 HDTV 1080P

14 1920*1080 33.71 29.97 74.176 HDTV 1080P

Only for training and service purposes

- 8 -

(2) HDMI Input (DTV)

No. Resolution H-freq(kHz) V-freq.(Hz) Pixel clock(MHz) Proposed Remarks

1 640*480 31.46 59.94 25.13 SDTV 480P

2 640*480 31.50 60.00 25.13 SDTV 480P

3 720*480 15.73 59.94 13.50 SDTV, DVD 480I(525I)

4 720*480 15.75 60.00 13.51 SDTV, DVD 480I(525I)

5 720*576 15.62 50.00 13.50

6 720*480 31.47 59.94 27.00 SDTV 480P

7 720*480 31.50 60.00 27.03 SDTV 480P

8 720*576 31.25 50.00 27.00 SDTV 576P

9 1280*720 44.96 59.94 74.18 HDTV 720P

10 1280*720 45.00 60.00 74.25 HDTV 720P

11 1280*720 37.50 50.00 74.25 HDTV 720P

12 1920*1080 28.12 50.00 74.25 HDTV 1080I

13 1920*1080 33.72 59.94 74.18 HDTV 1080I

14 1920*1080 33.75 60.00 74.25 HDTV 1080I

15 1920*1080 26.97 23.97 63.30 HDTV 1080P

16 1920*1080 27.00 24.00 63.36 HDTV 1080P

17 1920*1080 33.71 29.97 79.12 HDTV 1080P

18 1920*1080 33.75 30.00 79.20 HDTV 1080P

19 1920*1080 56.25 50.00 148.50 HDTV 1080P

20 1920*1080 67.43 59.94 148.35 HDTV 1080P

21 1920*1080 67.50 60.00 148.50 HDTV 1080P

22 3840*2160 53.95 23.98 297.00 UDTV 2160P UHD only

23 3840*2160 54.00 24.00 297.00 UDTV 2160P UHD only

24 3840*2160 56.25 25.00 297.00 UDTV 2160P UHD only

25 3840*2160 61.43 29.97 297.00 UDTV 2160P UHD only

26 3840*2160 67.50 30.00 297.00 UDTV 2160P UHD only

27 3840*2160 112.50 50.00 594.00 UDTV 2160P(DVB) UHDonly(Port1,2)-LM15U Only

28 3840*2160 134.86 59.94 593.41 UDTV 2160P UHDonly(Port1,2)-LM15U Only

29 3840*2160 135.00 60.00 594.00 UDTV 2160P UHDonly(Port1,2)-LM15U Only

30 4096*2160 53.95 23.98 297.00 UDTV 2160P UHD only

31 4096*2160 54.00 24.00 297.00 UDTV 2160P UHD only

32 4096*2160 56.25 25.00 297.00 UDTV 2160P UHD only

33 4096*2160 61.43 29.97 297.00 UDTV 2160P UHD only

34 4096*2160 67.50 30.00 297.00 UDTV 2160P UHD only

35 4096*2160 112.50 50.00 594.00 UDTV 2160P(DVB) UHDonly(Port1,2)-LM15U Only

36 4096*2160 134.86 59.94 593.41 UDTV 2160P UHDonly(Port1,2)-LM15U Only

37 4096*2160 135.00 60.00 594.00 UDTV 2160P UHDonly(Port1,2)-LM15U Only

SDTV, DVD 576I(625I) 50Hz

Spec. out but display

Only for training and service purposes

- 9 -

(3) HDMI Input (PC)

No. Resolution H-freq(kHz) V-freq.(Hz) Pixel clock(MHz) Proposed Remarks

1 640*350 31.46 70.09 25.17 EGA

2 720*400 31.46 70.08 28.32 DOS

3 640*480 31.46 59.94 25.17 VESA(VGA)

4 800*600 37.87 60.31 40.00 VESA(SVGA)

5 1024*768 48.36 60.00 65.00 VESA(XGA)

6 1152*864 54.34 60.05 80.00 VESA

7 1280*1024 63.98 60.02 109.00 VESA(SXGA) FHD only

8 1360*768 47.71 60.01 85.00 VESA(WXGA)

9 1920*1080 67.50 60.00 158.40 WUXGA(CEA 861D) FHD only

10 3840*2160 67.50 30.00 297.00 UDTV 2160P UHD only

11 3840*2160 56.25 25.00 297.00 UDTV 2160P UHD only

12 3840*2160 54.00 24.00 297.00 UDTV 2160P UHD only

13 4096*2160 53.95 23.97 296.703 UDTV 2160P UHD only

14 4096*2160 54.00 24.00 297.00 UDTV 2160P UHD only

5.2. 3D Mode

(1) RF Input

No. Resolution H-freq(kHz) V-freq.(Hz) Pixel clock(MHz) Proposed Remarks

1 1280*720 37.50 50 74.25 HDTV 720P 2D to 3D, Side by Side, Top & Bottom

2 1920*1080 28.13 50 74.25 HDTV 1080I 2D to 3D, Side by Side, Top & Bottom

(2) HDMI Input (3D supported mode automatically)

No. Resolution H-freq(kHz) V-freq.(Hz) Pixel clock(MHz) VIC

31.46 / 31.50 59.94/ 60.00 25.13/25.20 1

1 640*480

2 720*480

3 720*576 15.62 50.00 27.00 21

4 720*576

31.46 / 31.50 59.94/ 60.00 50.35/50.40 1 Side-by-side(Full) (SDTV 480P)

62.93 / 63.00 59.94/ 60.00 50.35/50.40 1

31.46 / 31.50 59.94 / 60.00 27.00/27.03 2,3

31.46 / 31.50 59.94 / 60.00 27.00/27.03 2,3 Side-by-side(Full) (SDTV 480P)

62.93 /63.00 59.94 / 60.00 54.00/54.06 2,3

31.25 50.00 27.00 17,18

62.50 50.00 54.00 17,18

- 10 -

Only for training and service purposes

3D input

proposed mode

Top-and-Bottom

Side-by-side(half)

Frame packing

Line alternative

Top-and-Bottom

Side-by-side(half)

Frame packing

Line alternative

Top-and-Bottom Side-by-side(half) Side-by-side(Full)

Frame packing

Top-and-Bottom Side-by-side(half) Side-by-side(Full)

Frame packing

Line alternative

Proposed

Secondary(SDTV 480P) Secondary(SDTV 480P)

Secondary(SDTV 480P)

(SDTV 480P)

Secondary(SDTV 480P) Secondary(SDTV 480P)

Secondary(SDTV 480P)

(SDTV 480P)

(SDTV 576I)

Secondary(SDTV 576I)

(SDTV 576I) Secondary(SDTV 576I) Secondary(SDTV 576I)

Secondary(SDTV 576P) Secondary(SDTV 576P)

(SDTV 576P)

Secondary(SDTV 576P)

(SDTV 576P)

5 1280*720

6 1920*1080

7 1920*1080

37.50 50.00 74.25 19

37.50 50.00 148.50 19 Side-by-side(Full) (HDTV 720P)

44.96 / 45.00 59.94 / 60.00 74.17/74.25 4

44.96 / 45.00 59.94 / 60.00 148.35/148.50 4 Side-by-side(Full) (HDTV 720P)

75.00 50.00 148.50 19

89.91/90.00 59.94 / 60.00 148.35/148.50 4

28.12 50.00 74.25 20

28.12 50.00 148.50 20 Side-by-side(Full) (HDTV 1080I)

33.72 / 33.75 59.94 / 60.00 74.17/74.25 5

33.72 / 33.75 59.94 / 60.00 148.35/148.50 5 Side-by-side(Full) (HDTV 1080I)

56.25 50.00 148.50 20 Frame packing

67.43/67.50 59.94 / 60.00 148.35/148.50 5 Frame packing

26.97 / 27.00 23.97 / 24.00 74.17 / 74.25 32

26.97 / 27.00 23.97 / 24.00 148.35 / 148.50 32 Side-by-side(Full) (HDTV 1080P)

28.12 25.00 74.25 33

28.12 25.00 148.50 33 Side-by-side(Full) (HDTV 1080P)

33.71 / 33.75 29.97 / 30.00 74.18/74.25 34

33.71 / 33.75 29.97 / 30.00 148.35/148.50 34 Side-by-side(Full) (HDTV 1080P)

43.94/54.00 23.97 / 24.00 148.35/148.50 32

56.25 25.00 148.50 33

67.43 / 67.5 29.97 / 30.00 148.35/148.50 34

56.25 50.00 148.50 31

67.43 / 67.50 59.94 / 60.00 148.35/148.50 16

Top-and-Bottom

Side-by-side(half)

Top-and-Bottom

Side-by-side(half)

Frame packing

Line alternative

Frame packing

Line alternative

Top-and-Bottom

Side-by-side(half)

Top-and-Bottom

Side-by-side(half)

Top-and-Bottom

Side-by-side(half)

Top-and-Bottom

Side-by-side(half)

Top-and-Bottom

Side-by-side(half)

Frame packing

Line alternative

Frame packing

Line alternative

Frame packing

Line alternative

Top-and-Bottom

Side-by-side(half)

Top-and-Bottom

Side-by-side(half)

Primary(HDTV 720P) Primary(HDTV 720P)

Primary(HDTV 720P)

(HDTV 720P)

Primary(HDTV 720P)

(HDTV 720P)

Secondary(HDTV 1080I)

Primary(HDTV 1080I)

Secondary(HDTV 1080I)

Primary(HDTV 1080I)

(HDTV 1080I)

Primary(HDTV 1080I)

(HDTV 1080I)

Primary(HDTV 1080P) Primary(HDTV 1080P)

Secondary(HDTV 1080P) Secondary(HDTV 1080P)

Primary(HDTV 1080P)

Secondary(HDTV 1080P)

Primary(HDTV 1080P)

(HDTV 1080P)

Secondary(HDTV 1080P)

(HDTV 1080P)

Primary(HDTV 1080P)

(HDTV 1080P)

Primary(HDTV 1080P)

Secondary(HDTV 1080P)

Primary(HDTV 1080P)

Secondary(HDTV 1080P)

(3) DTV( 3D) (3D supported mode automatically)

No. Signal H-freq(kHz) V-freq.(Hz) Pixel clock(MHz) Proposed 3D input proposed mode

1 Frame compatible - - - -

- 11 -

Only for training and service purposes

Side by Side(half)

Top & Bottom

(4) DTV/ATV(CVBS/SCART) Input( 3D) (3D supported mode manually)

No Signal H-freq(kHz) V-freq.(Hz) Pixel clock(MHz) Proposed 3D input proposed mode

1 HD/SD - - - - 2D to 3D,

2 SD - - - -

(5) Component Input ( 3D) (3D supported mode manually)

No Resolution H-freq(kHz) V-freq.(Hz) Pixel clock Proposed 3D input proposed mode

1 1280*720 37.50 50.00 74.25 HDTV 720P

2 1280*720 45.00 60.00 74.25 HDTV 720P

3 1280*720 44.96 59.94 74.18 HDTV 720P

4 1920*1080 33.75 60.00 74.25 HDTV 1080I

5 1920*1080 33.72 59.94 74.18 HDTV 1080I

6 1920*1080 28.12 50.00 74.25 HDTV 1080I

7 1920*1080 67.50 60.00 148.50 HDTV 1080P

8 1920*1080 67.43 59.94 148.35 HDTV 1080P

9 1920*1080 27.00 24.00 74.25 HDTV 1080P

10 1920*1080 28.12 25.00 74.25 HDTV 1080P

11 1920*1080 56.25 50.00 74.25 HDTV 1080P

12 1920*1080 26.97 23.97 74.18 HDTV 1080P

13 1920*1080 33.75 30.00 74.25 HDTV 1080P

14 1920*1080 33.71 29.97 74.18 HDTV 1080P

Side by Side(half)

Top & Bottom

2D to 3D,

Side by Side(half), Top & Bottom

2D to 3D,

Side by Side(half), Top & Bottom

2D to 3D,

Side by Side(half), Top & Bottom

2D to 3D,

Side by Side(half), Top & Bottom

2D to 3D,

Side by Side(half), Top & Bottom

2D to 3D,

Side by Side(half), Top & Bottom

2D to 3D,

Side by Side(half), Top & Bottom

2D to 3D,

Side by Side(half), Top & Bottom

2D to 3D,

Side by Side(half), Top & Bottom

2D to 3D,

Side by Side(half), Top & Bottom

2D to 3D,

Side by Side(half), Top & Bottom

2D to 3D,

Side by Side(half), Top & Bottom

2D to 3D,

Side by Side(half), Top & Bottom

2D to 3D,

Side by Side(half), Top & Bottom

Only for training and service purposes

- 12 -

(6) HDMI-PC Input (3D) (3D supported mode manually)

No Resolution H-freq(kHz) V-freq.(Hz) Pixel clock(MHz) Proposed 3D input proposed mode

1 1024*768 48.36 60.00 65.00 HDTV 768P 2D to 3D,

2 1360*768 47.71 60.00 HDTV 768P

3 1920*1080 67.50 60.00 148.50 HDTV 1080P

4

5

6 Others - - -

3840*2160

(Ultea HD model only)

4096*2160

(Ultea HD model only)

54.00 24.00 296.70

56.25 25.00 297.00

67.50 30.00 296.70

54 24.00 297.00 HDTV 2160P

HDTV 2160P

640*350 720*400 640*480 800*600

1152*864

Side by Side(half),

Top & Bottom

2D to 3D,

Side by Side(half),

Top & Bottom,

Checker Board,

Row Interleaving,

Column Interleaving

2D to 3D,

Top & Bottom(half)

Side by Side(half)

2D to 3D,

Side by Side(half),

Top & Bottom

(7) HDMI-DTV (3D supported mode manually)

No Resolution H-freq(kHz) V-freq.(Hz) Pixel clock(MHz) Proposed 3D input proposed mode

1 720*480 31.50 60.00 27.03 SDTV 480P

2 720*576 31.25 50.00 27.00 SDTV 576P

3 1280*720

4 1920*1080

5 1920*1080

3840*2160

6

4096*2160

(Ultra HD model

only)

45.00 60.00 74.25 HDTV 720P

37.50 50.00 74.25 HDTV 720P

33.75 60.00 74.25 HDTV 1080I

28.12 50.00 74.25 HDTV 1080I

27.00 24.00 74.25 HDTV 1080P 2D to 3D, Side by Side(Half),

28.12 25.00 74.25 HDTV 1080P

33.75 30.00 74.25 HDTV 1080P

67.50 60.00 148.50 HDTV 1080P

56.25 50.00 148.50 HDTV 1080P

53.95 23.97 297.00

54.00 24.00 296.70

56.25 25.00 297.00

61.43 29.97 297.00

67.50 30.00 296.70

112.50

135.00

50.00

(HDMI1,HDMI2 Only)

60.00

(HDMI1,HDMI2 Only)

594.00

HDTV 2160P

2D to 3D, Side by Side(Half),

Top & Bottom, Checker Board,

Row Interleaving,

Column Interleaving

2D to 3D, Side by Side(Half),

Top & Bottom

Top & Bottom, Checker Board,

Row Interleaving,

Column Interleaving

2D to 3D, Side by Side(Half),

Top & Bottom, Checker Board,

Row Interleaving,

Column Interleaving

2D to 3D,

Top & Bottom(half), Side by

Side(half),

2D to 3D,

Side by Side(half)

Top & Bottom

Only for training and service purposes

- 13 -

(8) USB – Movie (3D) (3D supported mode manually)

No Resolution H-freq(kHz) V-freq.(Hz) Pixel clock(MHz) 3D input proposed mode

1 Under 704x480 - - - 2D to 3D

Over 704x480

2

Under 1080P

- - - 2D to 3D, Side by Side(Half), Top & Bottom

interlaced

2D to 3D, Side by Side(Half), Top & Bottom,

Over 704x480

3

Under 1080P

progressive

- 50 / 60 -

- others -

Checker Board, Row Interleaving,

Column Interleaving, Column Interleaving

2D to 3D, Side by Side(Half), Top & Bottom,

Checker Board, Row Interleaving,

Column Interleaving

4

Over 2160P

(Ultra HD model only)

- 24/25/30/50/60 - 2D to 3D, Side by Side(Half), Top & Bottom

(9) USB, DLNA -Photo (3D) (3D supported mode manually)

No Resolution H-freq(kHz) V-freq.(Hz) Pixel clock(MHz) 3D input proposed mode

1 USB(photo) - - - 2D to 3D, Side by Side(Half), Top & Bottom

(10) Miracast Intel WIDI (3D supported mode manually)

No Resolution H-freq(kHz) V-freq.(Hz) Pixel clock(MHz) 3D input proposed mode

1 1024X768p - 30 / 60 -

2D to 3D, Side by Side(Half), Top & Bottom2 1280x720p - 30.00 / 60.00 -

3 1920X1080p 30.00 / 60.00

4 Others - 2D to 3D

(11) USB, DLNA (3D) (3D supported mode automatically)

No Resolution H-freq(kHz) V-freq.(Hz) Pixel clock(MHz) 3D input proposed mode

1 1080p 33.75 30.00 74.25 Side by Side(Half), Top & Bottom,

2 2160p 67.50 30.00 297.00

Checker Board,

MPO(Photo), JPS(Photo)

Remark: 3D Input mode

Side by Side Top & Bottom Checkerboard Single Frame

Sequential

- 14 -

Only for training and service purposes

Frame

Packing

Row

Interleaving

Column

Interleaving



2D to 3D

ADJUSTMENT INSTRUCTION

1. Application Range

This specification sheet is applied to all of the OLED TV with ED64B chassis.

2. Designation

(1) Because this is not a hot chassis, it is not necessary to

use an isolation transformer. However, the use of isolation

transformer will help protect test instrument. (2) Adjustment must be done in the correct order. (3) The adjustment must be performed in the circumstance of

25 °C ± 5 °C of temperature and 65 % ± 10 % of relative

humidity if there is no specific designation. (4) The input voltage of the receiver must keep AC 100-240

V~, 50/60 Hz. (5) The receiver must be operated for about 5 minutes prior to

the adjustment when module is in the circumstance of over

15.

In case of keeping module is in the circumstance of 0 °C, it should be placed in the circumstance of above 15 °C for 2 hours.

In case of keeping module is in the circumstance of below

-20 °C, it should be placed in the circumstance of above 15 °C for 3 hours.

[Caution] When still image is displayed for a period of 20 minutes or longer (especially where W/B scale is strong. Digital pattern 13ch and/or Cross hatch pattern 09ch), there can some afterimage in the black level area.

3.2. LAN Inspection

3.2.1. Equipment & Condition

▪ Each other connection to LAN Port of IP Hub and Jig

3.2.2. LAN inspection solution

▪ LAN Port connection with PCB ▪ Network setting at MENU Mode of TV ▪ setting automatic IP ▪ Setting state confirmation

- If automatic setting is finished, you confirm IP and MAC Address.

3.2.3. WIDEVINE key Inspection

- Confirm key input data at the "IN START" MENU Mode.

3. Automatic Adjustment

3.1. MAC address D/L, CI+ key D/L, Widevine key D/L, ESN D/L, HDCP2.0 D/L

Connect: USB port Communication Prot connection

▪ Com 1,2,3,4 and 115200(Baudrate)

Mode check: Online Only

▪ Check the test process : DETECT → MAC → ESN → Widevine → CI → HDCP20 ▪ Play: Press Enter key ▪ Result: Ready, Test, OK or NG ▪ Printer Out (MAC Address Label)

Only for training and service purposes

- 15 -

3.3. LAN PORT INSPECTION(PING TEST)

Connect SET → LAN port == PC → LAN Port

SET PC

3.5. CI+ Key checking method(Only EU Model)

Check whether the key was downloaded or not at ‘In Start’ menu. (Refer to below).

3.3.1. Equipment setting

(1) Play the LAN Port Test PROGRAM. (2) Input IP set up for an inspection to Test Program.

*IP Number : 12.12.2.2

3.3.2. LAN PORT inspection(PING TEST)

(1) Play the LAN Port Test Program. (2) Connect each other LAN Port Jack. (3) Play Test (F9) button and confirm OK Message. (4) Remove LAN CABLE.

3.4. Model name & Serial number Download

3.4.1. Model name & Serial number D/L

▪ Press "P-ONLY" key of service remote control.

(Baud rate : 115200 bps)

▪ Connect RS-232C Signal to USB Cable to USB. ▪ Write Serial number by use USB port. ▪ Must check the serial number at Instart menu.

3.4.2. Method & notice

(1) Serial number D/L is using of scan equipment. (2) Setting of scan equipment operated by Manufacturing

Technology Group.

(3) Serial number D/L must be conformed when it is produced

in production line, because serial number D/L is mandatory by D-book 4.0.

* Manual Download (Model Name and Serial Number)

If the TV set is downloaded by OTA or service man, sometimes model name or serial number is initialized.(Not always) There is impossible to download by bar code scan, so It need Manual download.

1) Press the "Instart" key of Adjustment remote control.

2) Go to the menu "7.Model Number D/L" like below photo.

3) Input the Factory model name(ex 65UG870V-ZA) or Serial number like photo.

=> Check the Download to CI+ Key value in LGset.

3.5.1. Check the method of CI+ Key value

(1) Check the method on Instart menu (2) Check the method of RS232C Command

1) Into the main ass’y mode(RS232: aa 00 00)

CMD 1 CMD 2 Data 0

A 0 0

2) Check the key download for transmitted command (RS232: ci 00 10)

CMD 1 CMD 2 Data 0

C I 1 0

3) Result value

- Normally status for download : OKx

- Abnormally status for download : NGx

3.5.2. Check the method of CI+ key value(RS232)

1) Into the main ass’y mode(RS232: aa 00 00)

CMD 1 CMD 2 Data 0

A A 0 0

2) Check the methed of CI+ key by command (RS232: ci 00 20)

CMD 1 CMD 2 Data 0

C I 2 0

3) Result value i 01 OK 1d1852d21c1ed5dcx

CI+ Key Value

3.6. WIFI MAC ADDRESS CHECK

(1) Using RS232 Command

H-freq(kHz) V-freq.(Hz)

Transmission [A][I][][Set ID][][20][Cr] [O][K][X] or [NG]

(2) Check the menu on in-start

4) Check the model name Instart menu. → Factory name

displayed. (ex 65UG870V-ZA)

5) Check the Diagnostics.(DTV country only) → Buyer

model displayed. (ex 65UG870V-ZA)

Only for training and service purposes

- 16 -

4. Manual Adjustment

* ADC adjustment is not needed because of OTP(Auto ADC

adjustment)

4.1. EDID(The Extended Display Identification Data)/DDC(Display Data Channel) download

4.1.1. Overview

It is a VESA regulation. A PC or a MNT will display an optimal resolution through information sharing without any necessity of user input. It is a realization of "Plug and Play".

4.1.2. Equipment

- Since embedded EDID data is used, EDID download JIG, HDMI cable and D-sub cable are not need.

- Adjustment remote control

4.1.3. Download method

(1) Press "ADJ" key on the Adjustment remote control, then

select "12.EDID D/L", By pressing "Enter" key, enter EDID D/L menu.

For HDMI EDID

DVI-D to HDMI or HDMI to HDMI

(2) Select "Start" button by pressing "Enter" key, HDMI1/

HDMI2/ HDMI3/ HDMI4 are writing and display OK or NG.

4.1.4. EDID DATA

▪ Reference

- HDMI1 ~ HDMI3

- In the data of EDID, bellows may be different by Input mode.

0 1 2 3 4 5 6 7 8 9 A B C D E F

0x00 00 FF FF FF FF FF FF 00 1E 6D

ⓒ

0x01 0x02 0F 50 54 A1 8 00 31 40 45 40 61 40 71 40 81 80 0x03 01 01 01 01 01 01 02 3A 80 18 71 38 2D 40 58 2C 0x04 45 00 40 84 63 00 00 1E 66 21 50 B0 51 00 1B 30 0x05 40 70 36 00 40 84 63 00 00 1E 00 00 00 FD 00 3A 0x06 3E 1E 53 10 00 0A 20 20 20 20 20 20 0x07 0x00 02 03 3A F1 4E 10 9F 04 13 05 14 03 02 12 20 21 0x01 22 15 01 29 3D 06 C0 15 07 50 0x02 0x03 0x04 2D 40 58 2C 45 00 40 84 63 00 00 1E 01 1D 80 18 0x05 71 1C 16 20 58 2C 25 00 40 84 63 00 00 9E 01 1D 0x06 00 72 51 D0 1E 20 6E 28 55 00 40 84 63 00 00 1E 0x07 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

01 03 80 A0 5A 78 0A EE 91 A3 54 4C 99 26

ⓓ

ⓕ

10 28 10 E3 05 03 01 02 3A 80 18 71 38

ⓕ

ⓐ Product ID ⓑ Serial No: Controlled on production line. ⓒ Month, Year: Controlled on production line:

ex) Monthly : ‘01’ → ‘01’, Year : ‘2016’ → ‘1A’

ⓓ Model Name(Hex): LGTV ⓔ Checksum(LG TV): Changeable by total EDID data. ⓕ Vendor Specific(HDMI)

ⓐ ⓑ

ⓕ

ⓓ

ⓔ1

01

ⓔ2

(1) EDID for 2D Model

1) DTS # HDMI 1(C/S : 9F 47) - HDMI UHD Deep On Case EDID Block 0, Bytes 0-127 [00H-7FH]

0 1 2 3 4 5 6 7 8 9 A B C D E F 00 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01 10 01 1 A 01 03 80 A0 5 A 78 0A EE 91 A3 54 4C 99 26 20 0F 50 54 A1 08 00 31 40 45 40 61 40 71 40 81 80 30 01 01 01 01 01 01 08 E8 00 30 F2 70 5A 80 B0 58 40 8A 00 40 84 63 00 00 1E 02 3A 80 18 71 38 2D 40 50 58 2C 45 00 40 84 63 00 00 1E 00 00 00 FD 00 3 A 60 3E 1E 88 3C 00 0 A 20 20 20 20 20 20 00 00 00 FC 70 00 4C 47 20 54 56 0 A 20 20 20 20 20 20 20 01 9F

EDID Block 1, Bytes 128-255 [80H-FFH]

0 1 2 3 4 5 6 7 8 9 A B C D E F 80 02 03 4B F1 58 61 60 10 1F 04 13 05 14 03 02 12 90 20 21 22 15 01 5D 5E 5F 65 66 62 63 64 29 3D 06

A0 C0 15 07 50 09 57 07 6E 03 0C 00 10 00 B8 3C 20 B0 00 80 01 02 03 04 67 D8 5D C4 01 78 80 03 E3 05 C0 C0 00 E4 0F 03 00 18 E3 06 07 01 01 1D 80 18 71 D0 1C 16 20 58 2C 25 00 40 84 63 00 00 9E 66 21 50 E0 B0 51 00 1B 30 40 70 36 00 40 84 63 00 00 1E 00 F0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 47

# HDMI 1(C/S : 9F 79) - HDMI UHD Deep Off Case EDID Block 0, Bytes 0-127 [00H-7FH]

0 1 2 3 4 5 6 7 8 9 A B C D E F

00 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01 10 01 1 A 01 03 80 A0 5 A 78 0A EE 91 A3 54 4C 99 26 20 0F 50 54 A1 08 00 31 40 45 40 61 40 71 40 81 80 30 01 01 01 01 01 01 08 E8 00 30 F2 70 5A 80 B0 58 40 8A 00 40 84 63 00 00 1E 02 3A 80 18 71 38 2D 40 50 58 2C 45 00 40 84 63 00 00 1E 00 00 00 FD 00 3 A 60 3E 1E 88 3C 00 0 A 20 20 20 20 20 20 00 00 00 FC 70 00 4C 47 20 54 56 0 A 20 20 20 20 20 20 20 01 9F

EDID Block 1, Bytes 128-255 [80H-FFH]

0 1 2 3 4 5 6 7 8 9 A B C D E F

80 02 03 3C F1 54 5D 10 1F 04 13 05 14 03 02 12 20 90 21 22 15 01 5E 5F 62 63 64 29 3D 06 C0 15 07 50 A0 09 57 07 6E 03 0C 00 10 00 B8 3C 20 00 80 01 02 B0 03 04 E5 0E 60 61 65 66 E3 06 07 01 01 1D 80 18 C0 71 1C 16 20 58 2C 25 00 40 84 63 00 00 9E 66 21 D0 50 B0 51 00 1B 30 40 70 36 00 40 84 63 00 00 1E E0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 F0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 79

# HDMI 2(C/S : 9F 37) - HDMI UHD Deep On Case EDID Block 0, Bytes 0-127 [00H-7FH]

0 1 2 3 4 5 6 7 8 9 A B C D E F

00 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01 10 01 1 A 01 03 80 A0 5 A 78 0A EE 91 A3 54 4C 99 26 20 0F 50 54 A1 08 00 31 40 45 40 61 40 71 40 81 80 30 01 01 01 01 01 01 08 E8 00 30 F2 70 5A 80 B0 58 40 8A 00 40 84 63 00 00 1E 02 3A 80 18 71 38 2D 40 50 58 2C 45 00 40 84 63 00 00 1E 00 00 00 FD 00 3 A 60 3E 1E 88 3C 00 0 A 20 20 20 20 20 20 00 00 00 FC 70 00 4C 47 20 54 56 0 A 20 20 20 20 20 20 20 01 9F

EDID Block 1, Bytes 128-255 [80H-FFH]

0 1 2 3 4 5 6 7 8 9 A B C D E F

80 02 03 4B F1 58 61 60 10 1F 04 13 05 14 03 02 12 90 20 21 22 15 01 5D 5E 5F 65 66 62 63 64 29 3D 06 A0 C0 15 07 50 09 57 07 6E 03 0C 00 20 00 B8 3C 20 B0 00 80 01 02 03 04 67 D8 5D C4 01 78 80 03 E3 05 C0 C0 00 E4 0F 03 00 18 E3 06 07 01 01 1D 80 18 71 D0 1C 16 20 58 2C 25 00 40 84 63 00 00 9E 66 21 50 E0 B0 51 00 1B 30 40 70 36 00 40 84 63 00 00 1E 00 F0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 37

Only for training and service purposes

- 17 -

# HDMI 2(C/S : 9F 69) - HDMI UHD Deep Off Case EDID Block 0, Bytes 0-127 [00H-7FH]

0 1 2 3 4 5 6 7 8 9 A B C D E F 00 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01 10 01 1 A 01 03 80 A0 5 A 78 0A EE 91 A3 54 4C 99 26 20 0F 50 54 A1 08 00 31 40 45 40 61 40 71 40 81 80 30 01 01 01 01 01 01 08 E8 00 30 F2 70 5A 80 B0 58 40 8A 00 40 84 63 00 00 1E 02 3A 80 18 71 38 2D 40 50 58 2C 45 00 40 84 63 00 00 1E 00 00 00 FD 00 3A 60 3E 1E 88 3C 00 0 A 20 20 20 20 20 20 00 00 00 FC 70 00 4C 47 20 54 56 0 A 20 20 20 20 20 20 20 01 9F

EDID Block 1, Bytes 128-255 [80H-FFH]

0 1 2 3 4 5 6 7 8 9 A B C D E F 80 02 03 3C F1 54 5D 10 1F 04 13 05 14 03 02 12 20 90 21 22 15 01 5E 5F 62 63 64 29 3D 06 C0 15 07 50 A0 09 57 07 6E 03 0C 00 20 00 B8 3C 20 00 80 01 02 B0 03 04 E5 0E 60 61 65 66 E3 06 07 01 01 1D 80 18 C0 71 1C 16 20 58 2C 25 00 40 84 63 00 00 9E 66 21 D0 50 B0 51 00 1B 30 40 70 36 00 40 84 63 00 00 1E E0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 F0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 69

# HDMI 3(C/S : 9F 27) - HDMI UHD Deep Off Case EDID Block 0, Bytes 0-127 [00H-7FH]

0 1 2 3 4 5 6 7 8 9 A B C D E F 00 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01 10 01 1 A 01 03 80 A0 5 A 78 0A EE 91 A3 54 4C 99 26 20 0F 50 54 A1 08 00 31 40 45 40 61 40 71 40 81 80 30 01 01 01 01 01 01 08 E8 00 30 F2 70 5A 80 B0 58 40 8A 00 40 84 63 00 00 1E 02 3A 80 18 71 38 2D 40 50 58 2C 45 00 40 84 63 00 00 1E 00 00 00 FD 00 3 A 60 3E 1E 88 3C 00 0 A 20 20 20 20 20 20 00 00 00 FC 70 00 4C 47 20 54 56 0 A 20 20 20 20 20 20 20 01 9F

EDID Block 1, Bytes 128-255 [80H-FFH]

0 1 2 3 4 5 6 7 8 9 A B C D E F 80 02 03 4B F1 58 61 60 10 1F 04 13 05 14 03 02 12 90 20 21 22 15 01 5D 5E 5F 65 66 62 63 64 29 3D 06 A0 C0 15 07 50 09 57 07 6E 03 0C 00 30 00 B8 3C 20 B0 00 80 01 02 03 04 67 D8 5D C4 01 78 80 03 E3 05 C0 C0 00 E4 0F 03 00 18 E3 06 07 01 01 1D 80 18 71 D0 1C 16 20 58 2C 25 00 40 84 63 00 00 9E 66 21 50 E0 B0 51 00 1B 30 40 70 36 00 40 84 63 00 00 1E 00 F0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 27

# HDMI 3(C/S : 9F 59) - HDMI UHD Deep Off Case EDID Block 0, Bytes 0-127 [00H-7FH]

0 1 2 3 4 5 6 7 8 9 A B C D E F 00 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01 10 01 1 A 01 03 80 A0 5 A 78 0A EE 91 A3 54 4C 99 26 20 0F 50 54 A1 08 00 31 40 45 40 61 40 71 40 81 80 30 01 01 01 01 01 01 08 E8 00 30 F2 70 5A 80 B0 58 40 8A 00 40 84 63 00 00 1E 02 3A 80 18 71 38 2D 40 50 58 2C 45 00 40 84 63 00 00 1E 00 00 00 FD 00 3 A 60 3E 1E 88 3C 00 0 A 20 20 20 20 20 20 00 00 00 FC 70 00 4C 47 20 54 56 0 A 20 20 20 20 20 20 20 01 9F

EDID Block 1, Bytes 128-255 [80H-FFH]

0 1 2 3 4 5 6 7 8 9 A B C D E F 80 02 03 3C F1 54 5D 10 1F 04 13 05 14 03 02 12 20 90 21 22 15 01 5E 5F 62 63 64 29 3D 06 C0 15 07 50 A0 09 57 07 6E 03 0C 00 30 00 B8 3C 20 00 80 01 02 B0 03 04 E5 0E 60 61 65 66 E3 06 07 01 01 1D 80 18

C0 71 1C 16 20 58 2C 25 00 40 84 63 00 00 9E 66 21 D0 50 B0 51 00 1B 30 40 70 36 00 40 84 63 00 00 1E E0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 F0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 59

* Checksum(HDMI 1/2/3)

Input

HDMI1 9F 47 9F 79

HDMI2 9F 37 9F 69

HDMI3 9F 27 9F 59

HDMI Deep Color On

FFh (Checksum)

HDMI Deep Color Off

FFh (Checksum)

2) AC3 # HDMI 1(C/S : 9F 50) - HDMI UHD Deep On Case EDID Block 0, Bytes 0-127 [00H-7FH]

0 1 2 3 4 5 6 7 8 9 A B C D E F

00 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01

10 01 1 A 01 03 80 A0 5 A 78 0A EE 91 A3 54 4C 99 26 20 0F 50 54 A1 08 00 31 40 45 40 61 40 71 40 81 80

30 01 01 01 01 01 01 08 E8 00 30 F2 70 5A 80 B0 58

40 8A 00 40 84 63 00 00 1E 02 3A 80 18 71 38 2D 40 50 58 2C 45 00 40 84 63 00 00 1E 00 00 00 FD 00 3A

60 3E 1E 88 3C 00 0 A 20 20 20 20 20 20 00 00 00 FC

70 00 4C 47 20 54 56 0 A 20 20 20 20 20 20 20 01 9F

EDID Block 1, Bytes 128-255 [80H-FFH]

0 1 2 3 4 5 6 7 8 9 A B C D E F 80 02 03 48 F1 58 61 60 10 1F 04 13 05 14 03 02 12 90 20 21 22 15 01 5D 5E 5F 65 66 62 63 64 26 15 07 A0 50 09 57 07 6E 03 0C 00 10 00 B8 3C 20 00 80 01 B0 02 03 04 67 D8 5D C4 01 78 80 03 E3 05 C0 00 E4 C0 0F 03 00 18 E3 06 07 01 01 1D 80 18 71 1C 16 20 D0 58 2C 25 00 40 84 63 00 00 9E 66 21 50 B0 51 00 E0 1B 30 40 70 36 00 40 84 63 00 00 1E 00 00 00 00 F0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50

# HDMI 1(C/S : 9F 82) – HDMI UHD Deep Off Case EDID Block 0, Bytes 0-127 [00H-7FH]

0 1 2 3 4 5 6 7 8 9 A B C D E F 00 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01

10 01 1 A 01 03 80 A0 5 A 78 0A EE 91 A3 54 4C 99 26 20 0F 50 54 A1 08 00 31 40 45 40 61 40 71 40 81 80

30 01 01 01 01 01 01 08 E8 00 30 F2 70 5A 80 B0 58

40 8A 00 40 84 63 00 00 1E 02 3A 80 18 71 38 2D 40 50 58 2C 45 00 40 84 63 00 00 1E 00 00 00 FD 00 3A

60 3E 1E 88 3C 00 0 A 20 20 20 20 20 20 00 00 00 FC

70 00 4C 47 20 54 56 0 A 20 20 20 20 20 20 20 01 9F

EDID Block 1, Bytes 128-255 [80H-FFH]

0 1 2 3 4 5 6 7 8 9 A B C D E F 80 02 03 39 F1 54 5D 10 1F 04 13 05 14 03 02 12 20 90 21 22 15 01 5E 5F 62 63 64 26 15 07 50 09 57 07 A0 6E 03 0C 00 10 00 B8 3C 20 00 80 01 02 03 04 E5 B0 0E 60 61 65 66 E3 06 07 01 01 1D 80 18 71 1C 16 C0 20 58 2C 25 00 40 84 63 00 00 9E 66 21 50 B0 51 D0 00 1B 30 40 70 36 00 40 84 63 00 00 1E 00 00 00 E0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 F0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 82

# HDMI 2(C/S : 9F 40) - HDMI UHD Deep On Case EDID Block 0, Bytes 0-127 [00H-7FH]

0 1 2 3 4 5 6 7 8 9 A B C D E F 00 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01

10 01 1 A 01 03 80 A0 5 A 78 0A EE 91 A3 54 4C 99 26 20 0F 50 54 A1 08 00 31 40 45 40 61 40 71 40 81 80

30 01 01 01 01 01 01 08 E8 00 30 F2 70 5A 80 B0 58

40 8A 00 40 84 63 00 00 1E 02 3A 80 18 71 38 2D 40 50 58 2C 45 00 40 84 63 00 00 1E 00 00 00 FD 00 3A

60 3E 1E 88 3C 00 0 A 20 20 20 20 20 20 00 00 00 FC

70 00 4C 47 20 54 56 0 A 20 20 20 20 20 20 20 01 9F

Only for training and service purposes

- 18 -

EDID Block 1, Bytes 128-255 [80H-FFH]

0 1 2 3 4 5 6 7 8 9 A B C D E F 80 02 03 48 F1 58 61 60 10 1F 04 13 05 14 03 02 12 90 20 21 22 15 01 5D 5E 5F 65 66 62 63 64 26 15 07

A0 50 09 57 07 6E 03 0C 00 20 00 B8 3C 20 00 80 01 B0 02 03 04 67 D8 5D C4 01 78 80 03 E3 05 C0 00 E4 C0 0F 03 00 18 E3 06 07 01 01 1D 80 18 71 1C 16 20 D0 58 2C 25 00 40 84 63 00 00 9E 66 21 50 B0 51 00 E0 1B 30 40 70 36 00 40 84 63 00 00 1E 00 00 00 00

F0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 40

EDID Block 1, Bytes 128-255 [80H-FFH]

0 1 2 3 4 5 6 7 8 9 A B C D E F 80 02 03 39 F1 54 5D 10 1F 04 13 05 14 03 02 12 20 90 21 22 15 01 5E 5F 62 63 64 26 15 07 50 09 57 07 A0 6E 03 0C 00 30 00 B8 3C 20 00 80 01 02 03 04 E5 B0 0E 60 61 65 66 E3 06 07 01 01 1D 80 18 71 1C 16 C0 20 58 2C 25 00 40 84 63 00 00 9E 66 21 50 B0 51 D0 00 1B 30 40 70 36 00 40 84 63 00 00 1E 00 00 00 E0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 F0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 62

# HDMI 2(C/S : 9F 72) - HDMI UHD Deep off Case EDID Block 0, Bytes 0-127 [00H-7FH]

0 1 2 3 4 5 6 7 8 9 A B C D E F 00 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01 10 01 1 A 01 03 80 A0 5 A 78 0A EE 91 A3 54 4C 99 26 20 0F 50 54 A1 08 00 31 40 45 40 61 40 71 40 81 80 30 01 01 01 01 01 01 08 E8 00 30 F2 70 5A 80 B0 58 40 8A 00 40 84 63 00 00 1E 02 3A 80 18 71 38 2D 40 50 58 2C 45 00 40 84 63 00 00 1E 00 00 00 FD 00 3A 60 3E 1E 88 3C 00 0 A 20 20 20 20 20 20 00 00 00 FC 70 00 4C 47 20 54 56 0 A 20 20 20 20 20 20 20 01 9F

EDID Block 1, Bytes 128-255 [80H-FFH]

0 1 2 3 4 5 6 7 8 9 A B C D E F 80 02 03 39 F1 54 5D 10 1F 04 13 05 14 03 02 12 20 90 21 22 15 01 5E 5F 62 63 64 26 15 07 50 09 57 07

A0 6E 03 0C 00 20 00 B8 3C 20 00 80 01 02 03 04 E5 B0 0E 60 61 65 66 E3 06 07 01 01 1D 80 18 71 1C 16 C0 20 58 2C 25 00 40 84 63 00 00 9E 66 21 50 B0 51 D0 00 1B 30 40 70 36 00 40 84 63 00 00 1E 00 00 00 E0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

F0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 72

# HDMI 3(C/S : 9F 30) - HDMI UHD Deep off Case EDID Block 0, Bytes 0-127 [00H-7FH]

0 1 2 3 4 5 6 7 8 9 A B C D E F 00 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01 10 01 1 A 01 03 80 A0 5 A 78 0A EE 91 A3 54 4C 99 26 20 0F 50 54 A1 08 00 31 40 45 40 61 40 71 40 81 80 30 01 01 01 01 01 01 08 E8 00 30 F2 70 5A 80 B0 58 40 8A 00 40 84 63 00 00 1E 02 3A 80 18 71 38 2D 40 50 58 2C 45 00 40 84 63 00 00 1E 00 00 00 FD 00 3A 60 3E 1E 88 3C 00 0 A 20 20 20 20 20 20 00 00 00 FC 70 00 4C 47 20 54 56 0 A 20 20 20 20 20 20 20 01 9F

EDID Block 1, Bytes 128-255 [80H-FFH]

0 1 2 3 4 5 6 7 8 9 A B C D E F 80 02 03 48 F1 58 61 60 10 1F 04 13 05 14 03 02 12 90 20 21 22 15 01 5D 5E 5F 65 66 62 63 64 26 15 07

A0 50 09 57 07 6E 03 0C 00 30 00 B8 3C 20 00 80 01 B0 02 03 04 67 D8 5D C4 01 78 80 03 E3 05 C0 00 E4 C0 0F 03 00 18 E3 06 07 01 01 1D 80 18 71 1C 16 20 D0 58 2C 25 00 40 84 63 00 00 9E 66 21 50 B0 51 00 E0 1B 30 40 70 36 00 40 84 63 00 00 1E 00 00 00 00

F0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30

# HDMI 3(C/S : 9F 62) - HDMI UHD Deep off Case EDID Block 0, Bytes 0-127 [00H-7FH]

0 1 2 3 4 5 6 7 8 9 A B C D E F 00 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01 10 01 1 A 01 03 80 A0 5 A 78 0A EE 91 A3 54 4C 99 26 20 0F 50 54 A1 08 00 31 40 45 40 61 40 71 40 81 80 30 01 01 01 01 01 01 08 E8 00 30 F2 70 5A 80 B0 58 40 8A 00 40 84 63 00 00 1E 02 3A 80 18 71 38 2D 40 50 58 2C 45 00 40 84 63 00 00 1E 00 00 00 FD 00 3A 60 3E 1E 88 3C 00 0 A 20 20 20 20 20 20 00 00 00 FC 70 00 4C 47 20 54 56 0 A 20 20 20 20 20 20 20 01 9F

* Checksum(HDMI 1/2/3)

Input

HDMI1 9F 50 9F 82

HDMI2 9F 40 9F 72

HDMI3 9F 30 9F 62

HDMI Deep Color On

FFh (Checksum)

HDMI Deep Color Off

FFh (Checksum)

3) PCM # HDMI 1(C/S : 9F C2) - HDMI UHD Deep On Case EDID Block 0, Bytes 0-127 [00H-7FH]

0 1 2 3 4 5 6 7 8 9 A B C D E F

00 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01

10 01 1 A 01 03 80 A0 5 A 78 0A EE 91 A3 54 4C 99 26 20 0F 50 54 A1 08 00 31 40 45 40 61 40 71 40 81 80

30 01 01 01 01 01 01 08 E8 00 30 F2 70 5A 80 B0 58

40 8A 00 40 84 63 00 00 1E 02 3A 80 18 71 38 2D 40 50 58 2C 45 00 40 84 63 00 00 1E 00 00 00 FD 00 3A

60 3E 1E 88 3C 00 0 A 20 20 20 20 20 20 00 00 00 FC

70 00 4C 47 20 54 56 0 A 20 20 20 20 20 20 20 01 9F

EDID Block 1, Bytes 128-255 [80H-FFH]

0 1 2 3 4 5 6 7 8 9 A B C D E F 80 02 03 45 F1 58 61 60 10 1F 04 13 05 14 03 02 12 90 20 21 22 15 01 5D 5E 5F 65 66 62 63 64 23 09 57 A0 07 6E 03 0C 00 10 00 B8 3C 20 00 80 01 02 03 04 B0 67 D8 5D C4 01 78 80 03 E3 05 C0 00 E4 0F 03 00 C0 18 E3 06 07 01 01 1D 80 18 71 1C 16 20 58 2C 25 D0 00 40 84 63 00 00 9E 66 21 50 B0 51 00 1B 30 40 E0 70 36 00 40 84 63 00 00 1E 00 00 00 00 00 00 00 F0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 C2

# HDMI 1(C/S : 9F F4) - HDMI UHD Deep off case EDID Block 0, Bytes 0-127 [00H-7FH]

0 1 2 3 4 5 6 7 8 9 A B C D E F 00 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01

10 01 1 A 01 03 80 A0 5 A 78 0A EE 91 A3 54 4C 99 26 20 0F 50 54 A1 08 00 31 40 45 40 61 40 71 40 81 80

30 01 01 01 01 01 01 08 E8 00 30 F2 70 5A 80 B0 58

40 8A 00 40 84 63 00 00 1E 02 3A 80 18 71 38 2D 40 50 58 2C 45 00 40 84 63 00 00 1E 00 00 00 FD 00 3A

60 3E 1E 88 3C 00 0 A 20 20 20 20 20 20 00 00 00 FC

70 00 4C 47 20 54 56 0 A 20 20 20 20 20 20 20 01 9F

EDID Block 1, Bytes 128-255 [80H-FFH]

0 1 2 3 4 5 6 7 8 9 A B C D E F 80 02 03 36 F1 54 5D 10 1F 04 13 05 14 03 02 12 20 90 21 22 15 01 5E 5F 62 63 64 23 09 57 07 6E 03 0C A0 00 10 00 B8 3C 20 00 80 01 02 03 04 E5 0E 60 61 B0 65 66 E3 06 07 01 01 1D 80 18 71 1C 16 20 58 2C C0 25 00 40 84 63 00 00 9E 66 21 50 B0 51 00 1B 30 D0 40 70 36 00 40 84 63 00 00 1E 00 00 00 00 00 00 E0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 F0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 F4

Only for training and service purposes

- 19 -

# HDMI 2(C/S : 9F B2) - HDMI UHD Deep On Case EDID Block 0, Bytes 0-127 [00H-7FH]

0 1 2 3 4 5 6 7 8 9 A B C D E F 00 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01 10 01 1 A 01 03 80 A0 5 A 78 0A EE 91 A3 54 4C 99 26 20 0F 50 54 A1 08 00 31 40 45 40 61 40 71 40 81 80 30 01 01 01 01 01 01 08 E8 00 30 F2 70 5A 80 B0 58 40 8A 00 40 84 63 00 00 1E 02 3A 80 18 71 38 2D 40 50 58 2C 45 00 40 84 63 00 00 1E 00 00 00 FD 00 3 A 60 3E 1E 88 3C 00 0 A 20 20 20 20 20 20 00 00 00 FC 70 00 4C 47 20 54 56 0 A 20 20 20 20 20 20 20 01 9F

# HDMI 3(C/S : 9F D4) - HDMI UHD Deep off case EDID Block 0, Bytes 0-127 [00H-7FH]

0 1 2 3 4 5 6 7 8 9 A B C D E F 00 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01 10 01 1 A 01 03 80 A0 5 A 78 0A EE 91 A3 54 4C 99 26 20 0F 50 54 A1 08 00 31 40 45 40 61 40 71 40 81 80 30 01 01 01 01 01 01 08 E8 00 30 F2 70 5A 80 B0 58 40 8A 00 40 84 63 00 00 1E 02 3A 80 18 71 38 2D 40 50 58 2C 45 00 40 84 63 00 00 1E 00 00 00 FD 00 3 A 60 3E 1E 88 3C 00 0 A 20 20 20 20 20 20 00 00 00 FC 70 00 4C 47 20 54 56 0 A 20 20 20 20 20 20 20 01 9F

EDID Block 1, Bytes 128-255 [80H-FFH]

0 1 2 3 4 5 6 7 8 9 A B C D E F 80 02 03 45 F1 58 61 60 10 1F 04 13 05 14 03 02 12 90 20 21 22 15 01 5D 5E 5F 65 66 62 63 64 23 09 57

A0 07 6E 03 0C 00 20 00 B8 3C 20 00 80 01 02 03 04 B0 67 D8 5D C4 01 78 80 03 E3 05 C0 00 E4 0F 03 00 C0 18 E3 06 07 01 01 1D 80 18 71 1C 16 20 58 2C 25 D0 00 40 84 63 00 00 9E 66 21 50 B0 51 00 1B 30 40 E0 70 36 00 40 84 63 00 00 1E 00 00 00 00 00 00 00

F0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 B2

# HDMI 2(C/S : 9F E4) - HDMI UHD Deep off case EDID Block 0, Bytes 0-127 [00H-7FH]

0 1 2 3 4 5 6 7 8 9 A B C D E F 00 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01 10 01 1 A 01 03 80 A0 5 A 78 0A EE 91 A3 54 4C 99 26 20 0F 50 54 A1 08 00 31 40 45 40 61 40 71 40 81 80 30 01 01 01 01 01 01 08 E8 00 30 F2 70 5A 80 B0 58 40 8A 00 40 84 63 00 00 1E 02 3A 80 18 71 38 2D 40 50 58 2C 45 00 40 84 63 00 00 1E 00 00 00 FD 00 3 A 60 3E 1E 88 3C 00 0 A 20 20 20 20 20 20 00 00 00 FC 70 00 4C 47 20 54 56 0 A 20 20 20 20 20 20 20 01 9F

EDID Block 1, Bytes 128-255 [80H-FFH]

0 1 2 3 4 5 6 7 8 9 A B C D E F 80 02 03 36 F1 54 5D 10 1F 04 13 05 14 03 02 12 20 90 21 22 15 01 5E 5F 62 63 64 23 09 57 07 6E 03 0C

A0 00 20 00 B8 3C 20 00 80 01 02 03 04 E5 0E 60 61 B0 65 66 E3 06 07 01 01 1D 80 18 71 1C 16 20 58 2C C0 25 00 40 84 63 00 00 9E 66 21 50 B0 51 00 1B 30 D0 40 70 36 00 40 84 63 00 00 1E 00 00 00 00 00 00 E0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

F0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 E4

# HDMI 3(C/S : 9F A2) - HDMI UHD Deep off case EDID Block 0, Bytes 0-127 [00H-7FH]

0 1 2 3 4 5 6 7 8 9 A B C D E F 00 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01 10 01 1 A 01 03 80 A0 5 A 78 0A EE 91 A3 54 4C 99 26 20 0F 50 54 A1 08 00 31 40 45 40 61 40 71 40 81 80 30 01 01 01 01 01 01 08 E8 00 30 F2 70 5A 80 B0 58 40 8A 00 40 84 63 00 00 1E 02 3A 80 18 71 38 2D 40 50 58 2C 45 00 40 84 63 00 00 1E 00 00 00 FD 00 3 A 60 3E 1E 88 3C 00 0 A 20 20 20 20 20 20 00 00 00 FC 70 00 4C 47 20 54 56 0 A 20 20 20 20 20 20 20 01 9F

EDID Block 1, Bytes 128-255 [80H-FFH]

0 1 2 3 4 5 6 7 8 9 A B C D E F 80 02 03 45 F1 58 61 60 10 1F 04 13 05 14 03 02 12 90 20 21 22 15 01 5D 5E 5F 65 66 62 63 64 23 09 57

A0 07 6E 03 0C 00 30 00 B8 3C 20 00 80 01 02 03 04 B0 67 D8 5D C4 01 78 80 03 E3 05 C0 00 E4 0F 03 00 C0 18 E3 06 07 01 01 1D 80 18 71 1C 16 20 58 2C 25 D0 00 40 84 63 00 00 9E 66 21 50 B0 51 00 1B 30 40 E0 70 36 00 40 84 63 00 00 1E 00 00 00 00 00 00 00

F0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 A2

EDID Block 1, Bytes 128-255 [80H-FFH]

0 1 2 3 4 5 6 7 8 9 A B C D E F 80 02 03 36 F1 54 5D 10 1F 04 13 05 14 03 02 12 20 90 21 22 15 01 5E 5F 62 63 64 23 09 57 07 6E 03 0C A0 00 30 00 B8 3C 20 00 80 01 02 03 04 E5 0E 60 61 B0 65 66 E3 06 07 01 01 1D 80 18 71 1C 16 20 58 2C C0 25 00 40 84 63 00 00 9E 66 21 50 B0 51 00 1B 30 D0 40 70 36 00 40 84 63 00 00 1E 00 00 00 00 00 00 E0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 F0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 D4

* Checksum(HDMI 1/2/3)

Input

HDMI1 9F C2 9F F4

HDMI2 9F B2 9F E4

HDMI3 9F A2 9F D4

HDMI Deep Color On

FFh (Checksum)

HDMI Deep Color Off

FFh (Checksum)

(2) 2 HDR DOLBY EDID for 2D Model(OLED55/65B6*-Z)

1) HDMI Deep Color OFF # HDMI 1(C/S : 9F 53) EDID Block 0, Bytes 0-127 [00H-7FH]

0 1 2 3 4 5 6 7 8 9 A B C D E F 00 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01 10 01 1A 01 03 80 A0 5A 78 0A EE 91 A3 54 4C 99 26 20 0F 50 54 A1 08 00 31 40 45 40 61 40 71 40 81 80 30 01 01 01 01 01 01 08 E8 00 30 F2 70 5A 80 B0 58 40 8A 00 40 84 63 00 00 1E 02 3A 80 18 71 38 2D 40 50 58 2C 45 00 40 84 63 00 00 1E 00 00 00 FD 00 3A 60 3E 1E 88 3C 00 0A 20 20 20 20 20 20 00 00 00 FC 70 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 01 9F

EDID Block 1, Bytes 128-255 [80H-FFH]

0 1 2 3 4 5 6 7 8 9 A B C D E F 80 02 03 3C F1 54 5D 10 1F 04 13 05 14 03 02 12 20 90 21 22 15 01 5E 5F 62 63 64 29 3D 06 C0 15 07 50 A0 09 57 07 6E 03 0C 00 10 00 B8 3C 20 00 80 01 02 B0 03 04 E5 0E 60 61 65 66 E3 06 07 01 01 1D 80 18 C0 71 1C 16 20 58 2C 25 00 40 84 63 00 00 9E 66 21 D0 50 B0 51 00 1B 30 40 70 36 00 40 84 63 00 00 1E E0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 F0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 53

# HDMI 2(C/S : 9F 43) EDID Block 0, Bytes 0-127 [00H-7FH]

0 1 2 3 4 5 6 7 8 9 A B C D E F 00 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01 10 01 1A 01 03 80 A0 5A 78 0A EE 91 A3 54 4C 99 26 20 0F 50 54 A1 08 00 31 40 45 40 61 40 71 40 81 80 30 01 01 01 01 01 01 08 E8 00 30 F2 70 5A 80 B0 58 40 8A 00 40 84 63 00 00 1E 02 3A 80 18 71 38 2D 40 50 58 2C 45 00 40 84 63 00 00 1E 00 00 00 FD 00 3A 60 3E 1E 88 3C 00 0A 20 20 20 20 20 20 00 00 00 FC 70 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 01 9F

Only for training and service purposes

- 20 -

EDID Block 1, Bytes 128-255 [80H-FFH]

0 1 2 3 4 5 6 7 8 9 A B C D E F 80 02 03 3C F1 54 5D 10 1F 04 13 05 14 03 02 12 20 90 21 22 15 01 5E 5F 62 63 64 29 3D 06 C0 15 07 50

A0 09 57 07 6E 03 0C 00 20 00 B8 3C 20 00 80 01 02 B0 03 04 E5 0E 60 61 65 66 E3 06 07 01 01 1D 80 18 C0 71 1C 16 20 58 2C 25 00 40 84 63 00 00 9E 66 21 D0 50 B0 51 00 1B 30 40 70 36 00 40 84 63 00 00 1E E0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

F0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 43

# HDMI 3(C/S : 9F 33) EDID Block 0, Bytes 0-127 [00H-7FH]

0 1 2 3 4 5 6 7 8 9 A B C D E F 00 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01 10 01 1A 01 03 80 A0 5A 78 0A EE 91 A3 54 4C 99 26 20 0F 50 54 A1 08 00 31 40 45 40 61 40 71 40 81 80 30 01 01 01 01 01 01 08 E8 00 30 F2 70 5A 80 B0 58 40 8A 00 40 84 63 00 00 1E 02 3A 80 18 71 38 2D 40 50 58 2C 45 00 40 84 63 00 00 1E 00 00 00 FD 00 3A 60 3E 1E 88 3C 00 0A 20 20 20 20 20 20 00 00 00 FC 70 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 01 9F

EDID Block 1, Bytes 128-255 [80H-FFH]

0 1 2 3 4 5 6 7 8 9 A B C D E F 80 02 03 3C F1 54 5D 10 1F 04 13 05 14 03 02 12 20 90 21 22 15 01 5E 5F 62 63 64 29 3D 06 C0 15 07 50

A0 09 57 07 6E 03 0C 00 30 00 B8 3C 20 00 80 01 02 B0 03 04 E5 0E 60 61 65 66 E3 06 07 01 01 1D 80 18 C0 71 1C 16 20 58 2C 25 00 40 84 63 00 00 9E 66 21 D0 50 B0 51 00 1B 30 40 70 36 00 40 84 63 00 00 1E E0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

F0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 33

# HDMI 4(C/S : 9F 23) EDID Block 0, Bytes 0-127 [00H-7FH]

0 1 2 3 4 5 6 7 8 9 A B C D E F 00 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01 10 01 1A 01 03 80 A0 5A 78 0A EE 91 A3 54 4C 99 26 20 0F 50 54 A1 08 00 31 40 45 40 61 40 71 40 81 80 30 01 01 01 01 01 01 08 E8 00 30 F2 70 5A 80 B0 58 40 8A 00 40 84 63 00 00 1E 02 3A 80 18 71 38 2D 40 50 58 2C 45 00 40 84 63 00 00 1E 00 00 00 FD 00 3A 60 3E 1E 88 3C 00 0A 20 20 20 20 20 20 00 00 00 FC 70 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 01 9F

EDID Block 1, Bytes 128-255 [80H-FFH]

0 1 2 3 4 5 6 7 8 9 A B C D E F 80 02 03 3C F1 54 5D 10 1F 04 13 05 14 03 02 12 20 90 21 22 15 01 5E 5F 62 63 64 29 3D 06 C0 15 07 50

A0 09 57 07 6E 03 0C 00 40 00 B8 3C 20 00 80 01 02 B0 03 04 E5 0E 60 61 65 66 E3 06 07 01 01 1D 80 18 C0 71 1C 16 20 58 2C 25 00 40 84 63 00 00 9E 66 21 D0 50 B0 51 00 1B 30 40 70 36 00 40 84 63 00 00 1E E0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

F0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 23

2) HDMI Deep Color ON # HDMI 1(C/S : 9F 14) EDID Block 0, Bytes 0-127 [00H-7FH]

0 1 2 3 4 5 6 7 8 9 A B C D E F 00 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01 10 01 1A 01 03 80 A0 5A 78 0A EE 91 A3 54 4C 99 26 20 0F 50 54 A1 08 00 31 40 45 40 61 40 71 40 81 80 30 01 01 01 01 01 01 08 E8 00 30 F2 70 5A 80 B0 58 40 8A 00 40 84 63 00 00 1E 02 3A 80 18 71 38 2D 40 50 58 2C 45 00 40 84 63 00 00 1E 00 00 00 FD 00 3A 60 3E 1E 88 3C 00 0A 20 20 20 20 20 20 00 00 00 FC 70 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 01 9F

EDID Block 1, Bytes 128-255 [80H-FFH]

0 1 2 3 4 5 6 7 8 9 A B C D E F 80 02 03 4B F1 58 61 60 10 1F 04 13 05 14 03 02 12 90 20 21 22 15 01 5D 5E 5F 65 66 62 63 64 29 3D 06 A0 C0 15 07 50 09 57 07 6E 03 0C 00 10 00 B8 3C 20 B0 00 80 01 02 03 04 67 6E 03 0C 00 10 00 B8 3C 20 C0 C0 00 E4 0F 03 00 18 E3 06 07 01 01 1D 80 18 71 D0 1C 16 20 58 2C 25 00 40 84 63 00 00 9E 66 21 50 E0 B0 51 00 1B 30 40 70 36 00 40 84 63 00 00 1E 00 F0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 14

# HDMI 2(C/S : 9F 04) EDID Block 0, Bytes 0-127 [00H-7FH]

0 1 2 3 4 5 6 7 8 9 A B C D E F 00 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01 10 01 1A 01 03 80 A0 5A 78 0A EE 91 A3 54 4C 99 26 20 0F 50 54 A1 08 00 31 40 45 40 61 40 71 40 81 80 30 01 01 01 01 01 01 08 E8 00 30 F2 70 5A 80 B0 58 40 8A 00 40 84 63 00 00 1E 02 3A 80 18 71 38 2D 40 50 58 2C 45 00 40 84 63 00 00 1E 00 00 00 FD 00 3A 60 3E 1E 88 3C 00 0A 20 20 20 20 20 20 00 00 00 FC 70 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 01 9F

EDID Block 1, Bytes 128-255 [80H-FFH]

0 1 2 3 4 5 6 7 8 9 A B C D E F 80 02 03 4B F1 58 61 60 10 1F 04 13 05 14 03 02 12 90 20 21 22 15 01 5D 5E 5F 65 66 62 63 64 29 3D 06 A0 C0 15 07 50 09 57 07 6E 03 0C 00 20 00 B8 3C 20 B0 00 80 01 02 03 04 67 6E 03 0C 00 10 00 B8 3C 20 C0 C0 00 E4 0F 03 00 18 E3 06 07 01 01 1D 80 18 71 D0 1C 16 20 58 2C 25 00 40 84 63 00 00 9E 66 21 50 E0 B0 51 00 1B 30 40 70 36 00 40 84 63 00 00 1E 00 F0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 04

# HDMI 3(C/S : 9F 33) EDID Block 0, Bytes 0-127 [00H-7FH]

0 1 2 3 4 5 6 7 8 9 A B C D E F 00 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01 10 01 1A 01 03 80 A0 5A 78 0A EE 91 A3 54 4C 99 26 20 0F 50 54 A1 08 00 31 40 45 40 61 40 71 40 81 80 30 01 01 01 01 01 01 08 E8 00 30 F2 70 5A 80 B0 58 40 8A 00 40 84 63 00 00 1E 02 3A 80 18 71 38 2D 40 50 58 2C 45 00 40 84 63 00 00 1E 00 00 00 FD 00 3A 60 3E 1E 88 3C 00 0A 20 20 20 20 20 20 00 00 00 FC 70 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 01 9F

EDID Block 1, Bytes 128-255 [80H-FFH]

0 1 2 3 4 5 6 7 8 9 A B C D E F 80 02 03 3C F1 54 5D 10 1F 04 13 05 14 03 02 12 20 90 21 22 15 01 5E 5F 62 63 64 29 3D 06 C0 15 07 50 A0 09 57 07 6E 03 0C 00 30 00 B8 3C 20 00 80 01 02 B0 03 04 E5 0E 60 61 65 66 E3 06 07 01 01 1D 80 18 C0 71 1C 16 20 58 2C 25 00 40 84 63 00 00 9E 66 21 D0 50 B0 51 00 1B 30 40 70 36 00 40 84 63 00 00 1E E0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 F0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 33

Only for training and service purposes

- 21 -

# HDMI 4(C/S : 9F 23) EDID Block 0, Bytes 0-127 [00H-7FH]

0 1 2 3 4 5 6 7 8 9 A B C D E F 00 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01 10 01 1A 01 03 80 A0 5A 78 0A EE 91 A3 54 4C 99 26 20 0F 50 54 A1 08 00 31 40 45 40 61 40 71 40 81 80 30 01 01 01 01 01 01 08 E8 00 30 F2 70 5A 80 B0 58 40 8A 00 40 84 63 00 00 1E 02 3A 80 18 71 38 2D 40 50 58 2C 45 00 40 84 63 00 00 1E 00 00 00 FD 00 3A 60 3E 1E 88 3C 00 0A 20 20 20 20 20 20 00 00 00 FC 70 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 01 9F

EDID Block 1, Bytes 128-255 [80H-FFH]

0 1 2 3 4 5 6 7 8 9 A B C D E F 80 02 03 3C F1 54 5D 10 1F 04 13 05 14 03 02 12 20 90 21 22 15 01 5E 5F 62 63 64 29 3D 06 C0 15 07 50

A0 09 57 07 6E 03 0C 00 40 00 B8 3C 20 00 80 01 02 B0 03 04 E5 0E 60 61 65 66 E3 06 07 01 01 1D 80 18 C0 71 1C 16 20 58 2C 25 00 40 84 63 00 00 9E 66 21 D0 50 B0 51 00 1B 30 40 70 36 00 40 84 63 00 00 1E E0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

F0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 23

* Checksum(HDMI 1/2/3/4) @Power Only Mode

- Due to External EEPROM for HDMI3&4, EDID C/S is shown below @ power only mode

Input

HDMI1 9F 53 9F 14

HDMI2 9F 43 9F 04

HDMI3 9F 33 9F 33

HDMI4 9F 23 9F 23

HDMI Deep Color On

FFh (Checksum)

HDMI Deep Color Off

FFh (Checksum)

Step 4) After check the “OK” message come out, take out

your hand from the Sensor module.

→ Check “Backlight” value change from “0” to “100” or

not. If it doesn’t change the value, the sensor is also defected one. You have to replace it.

4.2. White Balance Adjustment

4.2.1. Overview

▪ W/B adj. Objective & How-it-works

(1) Objective: To reduce each Panel's W/B deviation (2) How-it-works : When R/G/B gain in the OSD is at 192, it

means the panel is at its Full Dynamic Range. In order to prevent saturation of Full Dynamic range and data, one of R/G/B is fixed at 192, and the other two is lowered to find the desired value.

(3) Adjustment condition : normal temperature

1) Surrounding Temperature : 25 °C ± 5 °C

2) Warm-up time: About 5 Min

3) Surrounding Humidity : 20 % ~ 80 %

4.2.2. Equipment

(1) Color Analyzer: CA-210 (LED Module : CH 14) (2) Adjustment Computer(During auto adj., RS-232C protocol

is needed) (3) Adjustment Remote control (4) Video Signal Generator MSPG-925F 720p/216-Gray

(Model: 204, Pattern: 49)

→ Only when internal pattern is not available

• Color Analyzer Matrix should be calibrated using CS-100.

4.1.5. Green Eye Inspection Guide (Only use Germany and CIS, Spec out other EU country, but UF690 model only for Germany)

Step 1) Turn on the TV set. Step 2). Press “EYE” button on the Adjustment remote control.



Step 3) Block the Intelligent Sensor module on the front C/A

about 6 seconds. When the “Sensor Data” is lower than 20, you can see the “OK” message

→ If it doesn’t show “OK” message, the Sensor

Module is defected one.

You have to replace that with a good one.



4.2.3. Equipment connection MAP

wG

|ziGGyzTYZYjG

zG

z

୔pG{}GGGGSGG

jGh¡G

jG

୔G

wGnG

yzTYZYjG



4.2.4. Adj. Command (Protocol)

START 6E A 50 A LEN A 03 A CMD A 00 A VA L A CS STOP

- LEN: Number of Data Byte to be sent

- CMD: Command

- VAL: FOS Data value

- CS: Checksum of sent data

- A: Acknowledge Ex) [Send: JA_00_DD] / [Ack: A_00_okDDX]

Only for training and service purposes

- 22 -

▪ RS-232C Command used during auto-adjustment.

RS-232C COMMAND

[CMD ID DATA]

wb 00 00 Begin White Balance adj.

wb 00 10 Gain adj.(internal white pattern)

wb 00 1f Gain adj. completed

wb 00 20 Offset adj.(internal white pattern)

wb 00 2f Offset adj. completed

wb 00 ff

End White Balance adj. (internal pattern disappears)

Explanation

Ex) wb 00 00 → Begin white balance auto-adj.

wb 00 10 → Gain adj. ja 00 ff → Adj. data

jb 00 c0 ... ...

wb 00 1f -> Gain adj. complete *(wb 00 20(Start), wb 00 2f(end)) → Off-set adj. wb 00 ff -> End white balance auto-adj.

▪ Adj. Map

Adj. Command

(lower

Data Range

(Hex.)

Default

(Decimal)

caseASCII)

CMD1 CMD2 MIN MAX

Cool R Gain j g 00 C0 TBD

G Gain j h 00 C0 TBD

B Gain j i 00 C0 TBD

Medium R Gain j a 00 C0 TBD

G Gain j b 00 C0 TBD

B Gain j c 00 C0 TBD

Warm R Gain j d 00 C0 TBD

G Gain j e 00 C0 TBD

B Gain j f 00 C0 TBD

4.2.5. Adj. method

(1) Auto adj. method

1) Set TV in adj. mode using POWER ON key.

2) Zero calibrate probe then place it on the center of the Display.

3) Connect Cable.(RS-232C to USB)

4) Select mode in adj. Program and begin adj.

5) When adj. is complete (OK Sign), check adj. status pre mode.(Warm, Medium, Cool)

6) Remove probe and RS-232C cable to complete adj.

▪ W/B Adj. must begin as start command “wb 00 00”, and

finish as end command “wb 00 ff”, and Adj. offset if need.

(2) Manual adjustment method

1) Set TV in Adj. mode using POWER ON.

2) Zero Calibrate the probe of Color Analyzer, then place it on the center of LCD module within 10 cm of the surface.

3) Press ADJ key → EZ adjust using adj. R/C → 7. WhiteBalance then press the cursor to the right(key ►).

(When right key(►) is pressed 216 Gray internal pattern

will be displayed)

4) One of R Gain / G Gain / B Gain should be fixed at 192, and the rest will be lowered to meet the desired value.

5) Adjustment is performed in COOL, MEDIUM, WARM 3 modes of color temperature.

** G-fix adjustment Adjust modes (Cool), Fix the G gain to 172 (default data) and change the others (G/B Gain). Adjust two modes(Medium / Warm), Fix the one of R/G/B gain to 192 (default data) and decrease the others. If internal pattern is not available, use RF input. In EZ Adj. menu 7.White Balance, you can select one of 2 Testpattern: ON, OFF. Default is inner(ON). By selecting OFF, you can adjust using RF signal in 216 Gray pattern.

▪ Adjustment condition and cautionary items

1) Lighting condition in surrounding area

Surrounding lighting should be lower 10 lux. Try to isolate adj. area into dark surrounding.

2) Probe location

- PDP: Color Analyzer (CA-100, CA-100+, CA210) probe should be firmly attached to the Module

- LCD: Color Analyzer (CA-210) probe should be within

10cm and perpendicular of the module surface (80°~ 100°)

3) Aging time

- After Aging Start, Keep the Power ON status during 5

Minutes.

- In case of LCD, Back-light on should be checked using

no signal or Full-white pattern.

4.2.6. Reference(White balance adjusmtment coordinate and color temperature)

▪ Luminance : 206 Gray ▪ Standard color coordinate and temperature using CS-1000

(over 26 inch)

Mode

Cool 0.271 0.270 13000K 0.0000

Medium 0.286 0.289 9300K 0.0000

Warm 0.313 0.329 6500K 0.0000

▪

Standard color coordinate and temperature using CA-210(CH 14)

Mode

Cool 0.271±0.002 0.270±0.002 13000K 0.0000

Medium 0.286±0.002 0.289±0.002 9300K 0.0000

Warm 0.313±0.002 0.329±0.002 6500K 0.0000

Coordinate

x y

Coordinate

x y

Temp ∆uv

Only for training and service purposes

- 23 -

4.2.7. EDGE & IOL LED White balance table

▪ Apply under the color coordinate table, for compensated

aging time.

-gumi & Global Model : (normal line)LGD

Aging

time

(Min)

1 0-2 282 289 297 308 324 348 2 3-5 281 287 296 306 323 346 3 6-9 279 284 294 303 321 343 4 10-19 277 280 292 299 319 339 5 20-35 275 277 290 296 317 336 6 36-49 274 274 289 293 316 333 7 50-79 273 272 288 291 315 331 8 80-119 272 271 287 290 314 330 9 Over 120 271 270 286 289 313 329

Cool Medium Warm

x y x y x y

271 270 286 289 313 329

(2) Medium

1) Purpose : Adjust the color temperature to reduce the deviation of the module color temperature.

2) Principle : To adjust the white balance without the

saturation, Fix the B gain to 192 (default data) and decrease the others.

3) Adjustment mode : mode – Medium

(3) Warm

1) Purpose : Adjust the color temperature to reduce the deviation of the module color temperature.

2) Principle : To adjust the white balance without the saturation, Fix the W gain to 192 (default data) and decrease the others.

3) Adjustment mode : mode – Warm

4.2.8.3. Reference (White Balance Adj. coordinate and color temperature.

(1) Luminance: 204 Gray, 80IRE (2) Standard color coordinate and temperature using CS-1000

(over 26 inch)

(*) AUO, INX, Sharp, CSOT, BOE model (Cool spec : 13000K) – 40UH63**-Z*/55UH65**-Z*

webOS Cool Medium Warm

x y x y x y

271 270 285 293 313 329

Target 278 280 293 299 320 339

4.2.8. OLED White balance

4.2.8.1. Auto WB calibration & 10% window pattern brightness check(HDR)

(1) Set TV in ADJ mode using P-ONLY key (or POWER ON

key)

(2) Place optical probe on the center of the display

- It need to check probe condition of zero calibration before adjustment.

(3) Connect RS-232C Cable (4) Select mode in ADJ Program and begin a adjustment. (5) When WB adjustment is completed with OK message,

check adjustment status of pre-set mode (Cool, Medium, Warm, 10% window pattern brightness check)

(6) Remove probe and RS-232C cable.

▪ W/B Adj. must begin as start command “wb 00 00” , and

finish as end command “wb 00 ff”, and Adj. offset if need.

4.2.8.2. OLED White balance table (1) Cool Mode

1) Purpose : Especially B-gain fix adjust leads to the luminance enhancement. Adjust the color temperature to reduce the deviation of the module color temperature.

2) Principle : To adjust the white balance without the saturation, Adjust the B gain more than 192 ( If R gain or G gain is more than 255 , G gain can adjust less than 192 ) and change the others ( R/G Gain ).

3) Adjustment mode : mode – Cool

4.2.8.4. Reference (White Balance Adj. coordinate and color temperature)

▪ Luminance: 204 Gray ▪ Standard color coordinate and temperature using CS-1000

(over 26 inch)

Mode Coordinate Temp

uv

x y

Cool 0.277 0.278 11,000K -0.0030

Medium 0.286 0.289 9300K 0.0000

Warm 0.313 0.329 6500K +0.0030

▪ Standard color coordinate and temperature using

CA-210(CH-17)

Mode Coordinate Temp

uv

x y

Cool 0.277±0.002 0.278±0.002 11000K -0.0030

Medium 0.286±0.002 0.289±0.002 9300K 0.0000

Warm 0.313±0.002 0.329±0.002 6500K +0.0030

Only for training and service purposes

- 24 -

4.3. Magic Motion Remote control test

- Equipment : RF Remote control for test, IR-KEY-Code Remote control for test

- You must confirm the battery power of RF-Remote control before test(recommend that change the battery per every lot)

- Sequence (test)

1) If you select the ‘start key(OK)’ on the Adjustment remote control, you can pairing with the TV SET.

2) You can check the cursor on the TV Screen, when select the "OK" key on the Adjustment remote control.

3) You must remove the pairing with the TV Set by select ‘Mute + OK Key’ on the Adjustment remote control.

4.4. Option selection per country

4.4.1. Overview

- Option selection is only done for models in AJ/JA/IL

4.4.2.Method

(1) Press ADJ key on the Adj. R/C, then select Country Group

Menu.

(2) Depending on destination, select Country Group Code or

Country Group then on the lower Country option, select

US, CA, MX. Selection is done using +, - or ►◄ KEY.

4.5. HDMI ARC Function Inspection

(1) Test equipment

- Optic Receiver Speaker

- MSHG-600 (SW: 1220 ↑)

- HDMI Cable (for 1.4 version)

(2) Test method

1) Insert the HDMI Cable to the HDMI ARC port from the master equipment. (HDMI2)

5. GND and Internal Pressure check

5.1. Method

(1) GND & Internal Pressure auto-check preparation

- Check that Power Cord is fully inserted to the SET. (If loose, re-insert)

(2) Perform GND & Internal Pressure auto-check

- Unit fully inserted Power cord, Antenna cable and A/V arrive to the auto-check process.

- Connect D-terminal to AV JACK TESTER

- Auto CONTROLLER(GWS103-4) ON

- Perform GND TEST

- If NG, Buzzer will sound to inform the operator.

- If OK, changeover to I/P check automatically. (Remove CORD, A/V form AV JACK BOX.)

- Perform I/P test

- If NG, Buzzer will sound to inform the operator.

- If OK, Good lamp will lit up and the stopper will allow the pallet to move on to next process.

5.2. Checkpoint

▪ TEST voltage

- GND: 1.5 KV / min at 100 mA

- SIGNAL: 3 KV / min at 100 mA

▪ TEST time: 1 second ▪ TEST POINT

- GND TEST = POWER CORD GND & SIGNAL CABLE

METAL GND

- Internal Pressure TEST = POWER CORD GND & LIVE &

NEUTRAL

▪ LEAKAGE CURRENT: At 0.5 mArms

6. Audio

No. Item Ty p Max Unit

Audio practical max Output,

1

L/R (Distortion=10% max

Output)

Speaker

2

(6/8Ω Impedance)

10 12 W

8.10 10.8 Vrms

10 12 W

EQ Off

AVL Off

Clear Voice Off

EQ On

AVL On

Clear Voice On

2) Check the sound from the TV Set.

3) Check the Sound from the Speaker or using AV & Optic TEST program (It’s connected to MSHG-600)

4.6. Ship-out mode check (In-stop)

- After final inspection, press In-Stop key of the Adjustment remote control and check that the unit goes to Stand-by mode.

Only for training and service purposes

- 25 -

- Measurement condition: (1) RF input: Mono, 1 KHz sine wave signal, 100 % Modulation (2) CVBS, Component: 1 KHz sine wave signal 0.5 Vrms

7. USB S/W Download (option, Service only)

(1) Put the USB Stick to the USB socket. (2) Automatically detecting update file in USB Stick

- If your downloaded program version in USB Stick is Lower, it didn’t work.

But your downloaded version is Higher, USB data is automatically detecting (Download Version High & Power only mode, Set is automatically Download) (3) Show the message “Copying files from memory”.

(4) Updating is starting.

(5) Updating completed, the TV will restart automatically

(6) If your TV is turned on, check your updated version and

Tool option. (explain the Tool option, next stage)

* If downloading version is more high than your TV have,

TV can lost all channel data. In this case, you have to channel recover. if all channel data is cleared, you didn’t have a DTV/ATV test on production line.

* After downloading, have to adjust Tool Option again.

(1) Push "IN-START" key in service remote control. (2) Select "Tool Option 1" and push "OK" key. (3) Punch in the number. (Each model has their number)

Only for training and service purposes

- 26 -

1. K2L

BLOCK DIAGRAM

Only for training and service purposes

- 27 -

2. K2L I2C

Only for training and service purposes

- 28 -

3. K2L Power

Only for training and service purposes

- 29 -

4. Tuner/CI

Only for training and service purposes

- 30 -

5. Video/Audio In

Only for training and service purposes

- 31 -

6. Audio Out

Only for training and service purposes

- 32 -

7. HDMI

Only for training and service purposes

- 33 -

8. USB / WIFI / M-REMOTE / UART

Only for training and service purposes

- 34 -

200

LV1 LV2

400

121

500

502

810

501

120

530

540

521

570

571

900

710

A22 A10

410

700

EXPLODED VIEW

IMPORTANT SAFETY NOTICE

Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the Schematic Diagram and EXPLODED VIEW. It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent Shock, Fire, or other Hazards. Do not modify the original design without permission of manufacturer.

Only for training and service purposes

- 35 -

1. Put the set on the at pad.

DISASSEMBLY

Only for training and service purposes

- 36 -

FAB30016103 (M4*12mm), 4EA

2. Remove Rear Small Cover.

Pull up bottom of Rear Small Cover to remove.

3. Remove Stand Screw and Stand.

Remove Screw 4EA rst, next remove Stand.

- 37 -

Only for training and service purposes

Add only 55”

4. Remove Back Cover Screw.

FAB31843216 (M3*5.5mm, Gray) 9EA

 Common use 55”/65”

FAB31843216 (M3*5.5mm, Gray) 1EA



5. Remove PowerCord Bracket.

Pull up Power Cord, than remove Bracket, next remove cord from PSU.

Only for training and service purposes

- 38 -

6. Remove Back Cover

Pull up bottom of Back Cover to remove.

Only for training and service purposes

- 39 -

TROUBLE SHOOTING GUIDE

LGE Internal Use Only

Contents of Standard Repair Process

LGE Internal Use Only

No. Error symptom (High category) Error symptom (Mid category) Page Remarks

1

2 No video/No audio 2

3 Picture broken/ Freezing 3

4 Color error 4

5

6

7

8

9 Wrecked audio/discontinuation/noise 9

10

11

12

A. Video error

B. Power error

C. Audio error

D. Function error

No video/Normal audio 1

Vertical/Horizontal bar, residual image,

light spot, external device color error

No power 6

Off when on, off while viewing, power

auto on/off

No audio/Normal video 8

Remote control & Local switch checking

MR15R operating checking 11

Wifi operating checking 12

5

7

10

13 External device recognition error 13

14 E. Noise Circuit noise, mechanical noise 14

15 F. Exterior error Exterior defect 15

First of all, Check whether there is SVC Bulletin in GSCS System for these model.

Standard Repair Process

LGE Internal Use Only

Error

symptom

A. Video error

No video/ Normal audio

Established

date

Revised date

First of all, Check whether all of cables between board is inserted properly or not.

(Main B/D↔ Power B/D, LVDS Cable, Speaker Cable, IR B/D Cable,,,)

☞A9 ☞A1

N

Y

Check Back Light On with naked eye

☞A9

Check Power Board 24V output

On

Normal voltage

N

Repair Power Board or parts

Y N Check Power

Board 24V, 12V,3.5V etc.

Replace Inverter

Y

or module

Normal

voltage

N

Repair Power Board or parts

End

Replace T-con/Main

Y

Board or module And Adjust VCOM

No video Normal audio

Normal

audio

Move to No video/No audio

1/16

※Precaution

Always check & record S/W Version and White Balance value before replacing the Main Board

☞A4 & A2

Replace Main Board

1

Re-enter White Balance value

Standard Repair Process

LGE Internal Use Only

Error

symptom

No Video/ No audio

☞A9

Check various voltages of Power Board ( 13V or 24V)

A. Video error

No video/ No audio

Normal

voltage?

Replace Power Board and repair parts

Y

N

Check and replace MAIN B/D

Established

date

Revised date

End

2/16

2

Standard Repair Process

LGE Internal Use Only

☞ A3

Check RF Signal level

Normal Signal?

N

Check RF Cable

Connection

1. Reconnection

2. Install Booster

Normal

Picture?

Y

Close

Y

N

Error

symptom

A. Video error

Picture broken/ Freezing

Established

date

Revised date

. By using Digital signal level meter . By using Diagnostics menu on OSD

( All Settings→ Channels → Channel Tuning → Manual Tuning → Check the Signal )

- Signal strength (Normal : over 50%)

- Signal Quality (Normal: over 50%)

Check whether other equipments have problem or not.

(By connecting RF Cable at other equipment)

→ DVD Player ,Set-Top-Box, Different maker TV etc`

☞ A4

Normal

Picture?

Contact with signal distributor

or broadcaster (Cable or Air)

Y

S/W Version

N

Check

SVC

Bulletin?

S/W Upgrade

Normal

Picture?

Y

N

Check

Tuner soldering

N

Replace

Main B/D

3/16

Y

Close

3

Standard Repair Process

LGE Internal Use Only

☞A6

Check color by input

-External Input

-COMPONENT

-AV

-HDMI

Error

symptom

Color

error?

Check error color input mode

☞ A7

※ Check

and replace

Y

Link Cable (V by one)

N

and contact condition

External Input/

Component

error

A. Video error

Color error

Color

error?

Check external device and cable

N

Y

Replace Main B/D

Established

date

Revised date

External device

/Cable

normal

N

Color

error?

End

Y

Replace module

N

Replace Main/T-con B/D

4/16

HDMI error

Check external

device and cable

4

Request repair

for external

device/cable

N

External device

/Cable

normal

Y

Replace Main/T-con B/D

Standard Repair Process

LGE Internal Use Only

Error

symptom

Vertical / Horizontal bar, residual image,

A. Video error

light spot, external device color error

Vertical/Horizontal bar, residual image, light spot

☞A6

Check color condition by input

-External Input

-Component

-HDMI

Screen

normal?

N

Replace module

Check external

Y

device connection condition

Normal?

N

Request repair

for external device

External device screen error-Color error

Check screen condition by input

Check S/W Version

Check

version

Y

S/W Upgrade

N

-External Input

-Component

-HDMI/DVI

Component

☞ A7

Check and

Y

replace Link Cable

External

Input

error

Established

date

Revised date

Y

N

Replace Main/T-con B/D (adjust VCOM)

For LGD panel

Replace Main B/D

Screen

normal?

End

For other panel

Connect other external device and cable

(Check normal operation of External Input, Component, RGB and HDMI/DVI by connecting Jig, pattern Generator ,Set-top Box etc.

Screen

N

normal?

Y

Request repair for external device

5/16

Replace Module

N

Screen

normal?

Y

End

Replace Main/T-con B/D

Normal

screen?

End

N

Y

5

HDMI/

DVI

Connect other external device and cable

(Check normal operation of External Input, Component, RGB and HDMI/DVI by connecting Jig, pattern

Generator ,Set-top Box etc.

Y

Screen

normal?

N

Replace Main /T-con B/D

Standard Repair Process

LGE Internal Use Only

symptom

☞A8

Check Logo LED

. Stand-By: Red or Turn On . Operating: Turn Off

Power LED

Check Power cord was inserted properly

Error

On?

N

Normal?

Y

Close

Y

N

※

Check ST-BY 3.5V

☞A9

B. Power error

No power

DC Power on by pressing Power Key On Remote control

Normal

voltage?

Y

N

Established

date

Revised date

☞A9

Y

N

Check Power On ‘”High”

Replace Main B/D

Normal

operation?

☞A9

Measure voltage of each output of Power B/D

N

Y

Replace Main B/D

Normal

voltage?

Replace Power B/D

OK?

Y

6/16

Replace

Power B/D

Replace Power B/D

6

Standard Repair Process

LGE Internal Use Only

Check outlet

Check A/C cord

Check for all 3- phase power out

Error

symptom

Error?

Y

Fix A/C cord & Outlet and check each 3 phase out

B. Power error

Off when on, off while viewing, power auto on/off

☞A10

N

Check Power Off Mode

☞A9

(If Power Off mode is not displayed) Check Power B/D voltage

※ Caution Check and fix exterior of Power B/D Part

Abnormal

Established

date

Revised date

CPU

1

Normal

voltage?

Replace Power B/D

Replace Main B/D

Y

N

Replace Power B/D

Replace Main B/D

Normal?

N

7/16

Y

End

* Please refer to the all cases which can be displayed on power off mode.

Status Power off List Explanation

"POWER_OFF_BY_REMOTE_KEY" Power off by REMOTE CONTROL

"POWER_OFF_BY_OFF_TIMER" Power off by OFF TIMER

"POWER_OFF_BY_SLEEP_TIMER" Power off by SLEEP TIMER "POWER_OFF_BY_INSTOP" Power off by INSTOP KEY "POWER_OFF_BY_AUTO_OFF" Power off by AUTO OFF

Normal

Abnormal "POWER_OFF_BY_CPU_ABN" Power off by CPU Abnormal

"POWER_OFF_BY_ON_TIMER" Power off by ON TIMER "POWER_OFF_BY_RS232C" Power off by RS232C "POWER_OFF_BY_RESREC" Power off by Reservated Record "POWER_OFF_BY_RECEND" Power off by End of Recording "POWER_OFF_BY_SW_DW" Power off by S/W Download

"POWER_OFF_BY_UNKNOWN" Power off by unknown status except listed case

7

Standard Repair Process

LGE Internal Use Only

No audio Screen normal

Error

C. Audio error

symptom

No audio/ Normal video

☞A11 ☞A12+A9

Check user menu > Speaker off

Off

Cancel OFF

N

Y

Check audio B+ 24V of Power Board

Replace Power Board and repair parts

Established

date

Revised date

Normal voltage

Y

N

8/16

Check Speaker disconnection

Disconnection

Y

Replace Speaker

8

N

Replace MAIN Board

End

Standard Repair Process

LGE Internal Use Only

Check input signal

-RF

-External Input

signal

Error

symptom

C. Audio error

Wrecked audio/ discontinuation/noise

Established

date

Revised date

→ abnormal audio/discontinuation/noise is same after “Check input signal” compared to No audio

☞A12+A9

Check audio B+ Voltage (24V)

Y

Normal

voltage?

N

Replace Power B/D

Replace Main B/D

N

Y

Signal

normal?

N

Y

(When RF signal is not received)

Request repair to external

cable/ANT provider

(In case of

External Input

signal error) Check and fix external device

Wrecked audio/

Discontinuation/

Noise for

all audio

Wrecked audio/

Discontinuation/

Noise only

for D-TV

Wrecked audio/

Discontinuation/

Noise only

for Analog

Wrecked audio/

Discontinuation/

Noise only

for External Input

Check and replace speaker and connector

Replace Main B/D

Connect and check other external device

Normal

audio?

9/16

End

Check and fix external device

9

Standard Repair Process

LGE Internal Use Only

Error

symptom

D. Function error

Remote control & Local switch checking

1. Remote control(R/C) operating error

☞A13

Check R/C itself

Operation

Check R/C Operating

When turn off light

in room

If R/C operate,

Explain the customer

cause is interference

from light in room.

operating?

Normal

Y

N

Check & Replace

Baterry of R/C

Normal

operating?

Replace R/C

Check & Repair Cable connection Connector solder

Y

Close

N

Normal

operating?

Y

Close

☞A13

Check B+

N

On Main B/D

Established

date

Revised date

Y

N

3.5V

Normal

Voltage?

☞A9

Check 13v on Power B/D

Replace Power B/D or

Replace Main B/D

(Power B/D don’t have problem)

☞A13

Check IR

Output signal

10/16

Replace

Main B/D

Normal

Signal?

N

Repair/Replace

IR B/D

Y

10

Standard Repair Process

LGE Internal Use Only

Error

symptom

D. Function error

MR15R operating checking

2. MR15R (Magic remote control) operating error

☞A4

Check the

INSTART menu

RF Receiver ver

is “00.00”?

☞A14

Check & Repair

connection

Y

RF assy

☞A4

RF Receiver ver

is “00.00”?

Y

Down load the Firmware

* INSTART MENU12.RF

remote control Test3.

Firmware download

N

Check MR15R

itself Operation

N

Close

operating?

Check & Replace

Battery of MR15R

operating?

Normal

N

Normal

N

Replace

MR15R

Y

Press the

wheel

Close

Established

date

Revised date

Turn off/on the

Y

N

set and press

N

the wheel

Press the back key about 5sec

Is show ok

message?

Close

Is show ok

message?

Close

•If you conduct the loop at 3times, change the MR15R.

11/15

11

Standard Repair Process

LGE Internal Use Only

Error

symptom

3.Wifi operating error

☞A4

Check the

INSTART menu

Wi-Fi Mac value

is “NG”?

☞A15

Check & Repair

Y

Wifi cable

connection

☞A4

Wi-Fi Mac value

is “NG”?

D. Function error

Wifi operating checking

☞A15

N

Check the Wifi wafer

N

Close

1pin

Established

Revised date

Normal

Voltage?

Y

Close

date

N

12/16

Replace

Main B/D

Change the Wifi

Y

assy

12

Standard Repair Process

LGE Internal Use Only

Check input signal

Error

symptom

Y

Signal

input?

N

Check and fix

external device/cable

D. Function error

External device recognition error

Check technical information

- Fix information

- S/W Version

Technical

information?

Fix in

accordance

with technical

information

Y

External Input and

N

Component

Recognition error

HDMI/

DVI, Optical

Recognition error

Established

date

Revised date

14/16

Replace Main B/D

13

Standard Repair Process

LGE Internal Use Only

Identify nose type

Error

symptom

Circuit

noise

Mechanical

noise

Circuit noise, mechanical noise

Check location of noise

E. Noise

※ Mechanical noise is a natural phenomenon, and apply the 1st level description. When the customer does not agree, apply the process by stage. ※ Describe the basis of the description in “Part related to nose” in the Owner’s Manual.

Replace PSU

OR

Established

date

Revised date

※ When the nose is severe, replace the module

(For models with fix information, upgrade the S/W or provide the description)

※ If there is a “Tak Tak” noise from the cabinet, refer to the KMS fix information and then proceed as shown in the solution manual (For models without any fix information, provide the description)

15/16

14

Standard Repair Process

LGE Internal Use Only

Error

symptom

Zoom part with exterior damage

Module

damage

Cabinet

damage

Remote

control

damage

F. Exterior defect

Exterior defect

Replace module

Replace cabinet

Replace remote control

Established

date

Revised date

16/16

Stand

dent

Replace stand

15

Contents of Standard Repair Process Detail Technical Manual

LGE Internal Use Only

No. Error symptom Content Page Remarks

1

A. Video error_ No video/Normal audio

2 Check White Balance value A2

3

A. Video error_ video error /Video lag/stop

4 Version checking method A4

Check Vx1 lock LED light with naked eye A1

TUNER input signal strength checking method

A3

5 Tuner Checking Part A5

A. Video error _Vertical/Horizontal bar,

6

residual image, light spot

7 A. Video error_ Color error

8

Defected Type caused by T-Con/ Inverter/ Module

Connection diagram A6

Check Link Cable (EPI) reconnection condition

A7

Exchange Module (1) A-1/2

Exchange Module (2) A-2/2

Contents of Standard Repair Process Detail Technical Manual

LGE Internal Use Only

No. Error symptom Content Page Remarks

9

Check front display Logo A8

B. Power error_ No power

10 Check power input Voltage & ST-BY 3.5V A9

11

12

13

14

15

B. Power error_Off when on, off while viewing

C. Audio error_ No audio/Normal video

D. Function error

POWER OFF MODE checking method A10

Checking method in menu when there is no audio

Voltage and speaker checking method

when there is no audio

Remote control operation checking method

Motion Remote operation checking method

A11

A12

A13

A14

16 Wifi operation checking method A15

Standard Repair Process Detail Technical Manual

LGE Internal Use Only

Error

symptom

Content

A. Video error_No video/Normal audio

Check Vx1 lock LED light with naked eye

Established

date

Revised

date

A1

After Remove the Rear Cover, turning on the power and check with the naked eye, Whetehr you can see light from locations.

A1

Standard Repair Process Detail Technical Manual

LGE Internal Use Only

Error

symptom

Content

A. Video error_No video/Normal audio

Check White Balance value

Established

date

Revised

date

A2

Entry method

1. Press the ADJ button on the remote control for adjustment.

2. Enter into White Balance of item 12.

3. After recording the R, G, B (GAIN, Cut) value of Color Temp (Cool/Medium/Warm), re-enter the value after replacing the MAIN BOARD.

A2

Standard Repair Process Detail Technical Manual

LGE Internal Use Only

Error

symptom

Content

A. Video error_Video error, video lag/stop

TUNER input signal strength checking method

Established

date

Revised

date

All Settings  Channels Channel Tuning

A3

When the signal is strong, use the attenuator (-10dB, -15dB, -20dB etc.)

A3

Standard Repair Process Detail Technical Manual

LGE Internal Use Only

Error

symptom

Content

A. Video error_Video error, video lag/stop

Version checking method

1. Checking method for remote control for adjustment

Established

date

Revised

date

A4

Version

Press the IN-START with the remote control for adjustment

A4

Standard Repair Process Detail Technical Manual

LGE Internal Use Only

Error

symptom

Content

A. Video error_Video error, video lag/stop

TUNER checking part

Established

date

Revised

date

A5

Checking method:

1. Check the signal strength or check whether the screen is normal when the external device is connected.

2. After measuring each voltage from power supply, finally replace the MAIN BOARD.

A5

Standard Repair Process Detail Technical Manual

LGE Internal Use Only

Error

symptom

Content

A. Video error _Vertical/Horizontal bar,

residual image, light spot

Connection diagram

Established

date

Revised

date

A6

As the part connecting to the external input, check the screen condition by signal

A6

Standard Repair Process Detail Technical Manual

LGE Internal Use Only

Error

symptom

Content

Check Link Cable (EPI) reconnection condition

A. Video error_Color error

Established

date

Revised

date

A7

Check the contact condition of the Link Cable, especially dust or mis insertion.

A7

Appendix : Exchange the Module (1)

LGE Internal Use Only

Vertical abnormal display

Crosstalk

Brightness difference

Press damage

Line Dim

Crosstalk

Un-repairable Cases In this case please exchange the module.

Burnt

A – 1/2

Appendix : Exchange the Module (2)

LGE Internal Use Only

Angle view Color difference Brightness dot noise Half dead

Brightness difference

Mura

Green Noise on power on/off time

Line Defect

Un-repairable Cases In this case please exchange the module.

A – 2/2

Standard Repair Process Detail Technical Manual

LGE Internal Use Only

Error

symptom

Content

B. Power error _No power

Check front display Logo

Established

date

Revised

date

A8

ST-BY condition: On or Off

Power ON condition: Turn Off

A8

Standard Repair Process Detail Technical Manual

LGE Internal Use Only

Error

symptom

Content

B. Power error _No power

Check power input voltage

Check the DC 24V, 13V

Established

date

Revised

date

A9

Standard Repair Process Detail Technical Manual

LGE Internal Use Only

Error

symptom

Content

B. Power error _Off when on, off whiling viewing

POWER OFF MODE checking method

Established

date

Revised

date

A10

Entry method

1. Press the IN-START button of the remote control for adjustment

2. Check the entry into adjustment item 3(power On/Off Status)

A10

Standard Repair Process Detail Technical Manual

LGE Internal Use Only

Error

symptom

Content

C. Audio error_No audio/Normal video

Checking method in menu when there is no audio

Established

date

Revised

date

A11

Checking method

1. Press the Setting button on the remote control

2. Select the Sound function of the Menu

3. Select the Sound Out

4. Select TV Speaker

A11

Standard Repair Process Detail Technical Manual

1

SPK_R-_FT

2

SPK_R+_FT

3

SPK_L-_FT

4

SPK_L+_FT

5

SPK_R-_TW

6

SPK_R+_TW

7

SPK_L-_TW

8

SPK_L+_TW

LGE Internal Use Only

Error

symptom

Content

C. Audio error_No audio/Normal video

Voltage and speaker checking method when there is no audio

②

Established

date

Revised

date

A12

①

③

Checking order when there is no audio

① Check the contact condition of or 24V connector of Main Board

② Measure the 24V input voltage supplied from Power Board

(If there is no input voltage, remove and check the connector)

③ Connect the tester RX1 to the speaker terminal and if you hear the Chik Chik sound when you touch the

GND and output terminal, the speaker is normal.

A12

Standard Repair Process Detail Technical Manual

P4001

1

GND

2

KEY1

3

KEY2

4

3.5V_ST 5

GND

6

LOGO_LIGHT

7

IR

8

GND

9

EYE_SCL

10

EYE_SDA

LGE Internal Use Only

Error

symptom

Content

Remote control operation checking method

D. Function error

Established

date

Revised

date

A13

③

①

Checking order 1, 2. Check IR cable condition between IR & Main board.

3. Check the st-by 3.5V on the terminal 4

②

A13

Standard Repair Process Detail Technical Manual

P4102

1

GND

2

KEY1

3

KEY2

4

3.5V_ST 5

GND

6

LED_R

7

IR

8

GND

9

EYE_SCL

10

EYE_SDA

P4101

1

GND

2

BT_RESET

3

3D_SYNC_RF

4

WOL/WIFI_POWER_ON

5

GND

6

WIFI_DP

7

WIFI_DM

8

3.5V_WIFI

LGE Internal Use Only

Error

symptom

Content

Motion Remote operation checking method

D. Function error

Established

date

Revised

date

③

A14

①

②

Checking order

1. Check IR cable condition between IR & Main board.

2. Check WIFI Combo cable condition between WIFI Combo Assy & Main board.

3. Check the st-by 3.5V P4102 on the terminal 4

4. Check the 3.5V_WIFI P4101 on the terminal 8

A14

③

Standard Repair Process Detail Technical Manual

LGE Internal Use Only

Error

symptom

Content

Wifi operation checking method

D. Function error

① ②

Established

date

Revised

date

③

A15

P4000

1 GND 2 M_RFModule_RESET 3 NOT USE 4 WOL/WIFI_POWER_ON 5 GND 6 WIFI_DP 7 WIFI_DM

8 3.5V_WIFI

Checking order 1, 2. Check Wifi cable condition between Wifi assy & Main board.

3. Check the 3.3V on the terminal 8.

A15

LG OLED55B6, OLED65B6 Schematic

Specifications and Main Features

Frequently Asked Questions

User Manual