lg MU-50PZ90mA, MU-50PZ90vA, MU-50PZ90mB, MU-50PZ90vB, MU-50PZ90mK owners manual

...

PLASMA MONITOR

OWNER’S MANUAL

MODELS : MU-50PZ44/44M/44V

MU-50PZ44A/44MA/44VA MU-50PZ44B/44MB/44VB MU-50PZ44K/44MK/44VK MU-50PZ44R/44MR/44VR MU-50PZ44S/44MS/44VS MU-50PZ90/90M/90V MU-50PZ90A/90MA/90VA MU-50PZ90B/90MB/90VB MU-50PZ90K/90MK/90VK MU-50PZ90R/90MR/90VR MU-50PZ90S/90MS/90VS

Please read this owner’s manual thoroughly before operating the Monitor. Retain it for future reference. Record model number and serial number of the Monitor. See the label attached on the back of the Monitor and relate this information to your dealer if you ever require service.

Model Number : Serial Number :

P/NO : 3828VA0410A (RF03GB)

2 Plasma Monitor

Warning

WARNING:

TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to

the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of

important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING:

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

FCC NOTICE

• A Class B digital device

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

• Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

WARNING

RISK OF ELECTRIC SHOCK DO NOT OPEN

WARNING

TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

arning

Owner’s Manual 3

Safety Instructions

Important safeguards for you and your new product

Y our product has been manufactured and tested with your safety in mind. However, improper use can result in potential electrical shock or fire hazards. To avoid defeating the safeguards that have been built into your new product, please read and observe the following safety points when installing and using your new product, and save them for future reference.

Observing the simple precautions discussed in this booklet can help you get many years of enjoyment and safe operation that are built into your new product.

This product complies with all applicable U.S. Federal safety requirements, and those of the Canadian Standards Association.

1. Read Instructions

All the safety and operating instructions should be read before the product is operated.

2. Follow Instructions

All operating and use instructions should be followed.

3. Retain Instructions

The safety and operating instructions should be retained for future reference.

4. Heed Warnings

All warnings on the product and in the operating instructions should be adhered to.

5. Cleaning

Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

6. Water and Moisture

Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool.

7. Accessories, Carts, and Stands

Do not place this product on a slippery or tilted surface, or on an unstable cart, stand, tripod, bracket, or table. The product may slide or fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer.

8. Transporting Product

A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn.

9. Attachments

Do not use attachments not recommended by the product manufacturer as they may cause hazards.

10. Ventilation

Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.

11. Power Sources

This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions.

12. Power-Cord Polarization

This product is equipped with a three-wire grounding type plug, a plug having a third (grounding) pin. This plug will only fit into the grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug.

13. Power-Cord Protection

Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.

PORTABLE CART WARNING

Safety Instructions

4 Plasma Monitor

Safety Instructions

Antenna Lead in Wire

Antenna Discharge Unit (NEC Section 810-20)

Grounding Conductor (NEC Section 810-21)

Ground Clamps Power Service Grounding

Electrode System (NEC Art 250, Part H)

Ground Clamp

Electric Service

Equipment

Example of Grounding According to National Electrical Code Instructions

NEC - National Electrical Code

14. Outdoor Antenna Grounding

If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code (U.S.A.), ANSI/ NFPA 70 provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

15. Lightning

For added protection for this product (receiver) during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges.

16. Power Lines

An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

17. Overloading

Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock.

18. Object and Liquid Entry

Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.

19. Servicing

Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

20. Damage Requiring Service

Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:

a. If the power-supply cord or plug is damaged. b. If liquid has been spilled, or objects have fallen into the

product. c. If the product has been exposed to rain or water. d. If the product does not operate normally by following the

operating instructions. Adjust only those controls that are

covered by the operating instructions as an improper

adjustment of other controls may result in damage and

will often require extensive work by a qualified technician

to restore the product to its normal operation. e. If the product has been dropped or the cabinet has been

damaged. f. If the product exhibits a distinct change in performance.

21. Replacement Parts

When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.

22. Safety Check

Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition.

23. Wall or Ceiling Mounting

The product should be mounted to a wall or ceiling only as recommended by the manufacturer. The product may slide or fall, causing serious injury to a child or adult, and serious damage to the product.

24. Heat

The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

Safety Instructions continued

Owner’s Manual 5

Contents

After reading this manual, keep it handy for future reference.

Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3~4

Introduction

Controls and Connection Options . . . . . . . . . . . .7

Remote Control Key Functions . . . . . . . . . . . . . .8

Installation

Installation Instruction . . . . . . . . . . . . . . . . . . . .9~10

External Equipment Connections . . . . . . . . . .11~14

VCR Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Cable TV Setup . . . . . . . . . . . . . . . . . . . . . . . . 11

External A/V Source Setup . . . . . . . . . . . . . . . .12

DVD Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

DTV Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

PC Setup . . . . . . . . . . . . . . . . . . . . . . . . . .13~14

Operation

Turning on the Monitor . . . . . . . . . . . . . . . . . . . . .15

Menu Language Selection . . . . . . . . . . . . . . . . . .15

Video Menu Options

APC (Auto Picture Control) . . . . . . . . . . . . . . . . 16

Manual Picture Control . . . . . . . . . . . . . . . . . . .16

Auto Color Temperature Control . . . . . . . . . . . .16

Manual Color Temperature Control . . . . . . . . . .16

Audio Menu Options

DASP (Digital Auto Sound Processing) . . . . . . .17

Manual Sound Control . . . . . . . . . . . . . . . . . . .17

AVL(Auto Volume Leveler) . . . . . . . . . . . . . . . .17

Time Menu Options

Clock Setup . . . . . . . . . . . . . . . . . . . . . . . . . . .18

On/Off Timer Setup . . . . . . . . . . . . . . . . . . . . .18

Auto Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Sleep Timer . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Special Menu Options

Key Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

ISM Method . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Low power . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Menu Rotation For Vertical Viewing . . . . . . . . . .19

Screen Menu Options

Auto Adjustment . . . . . . . . . . . . . . . . . . . . . . . .20

Setting Picture Format . . . . . . . . . . . . . . . . . . .20

Picture Size Zoom . . . . . . . . . . . . . . . . . . . . . .20

Split Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Screen Position . . . . . . . . . . . . . . . . . . . . . . . .21

Manual Configure . . . . . . . . . . . . . . . . . . . . . . .21

Screen Adjustments . . . . . . . . . . . . . . . . . . . . .22

Initializing . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Selecting Wide VGA/XGA mode . . . . . . . . . . . .22

Luminance Noise Reduction . . . . . . . . . . . . . . .22

PIP (Picture-in-Picture) Feature

Watching PIP . . . . . . . . . . . . . . . . . . . . . . . . . .23

PIP Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

PIP Aspect Ratio . . . . . . . . . . . . . . . . . . . . . . . .23

Swapping PIP . . . . . . . . . . . . . . . . . . . . . . . . . .23

Moving PIP . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

Selecting an Input Signal Source for PIP . . . . . .23

Twin Picture Setup Options

Watching Twin Picture . . . . . . . . . . . . . . . . . . . .24

Sub Picture Size Adjustment . . . . . . . . . . . . . . .24

Swapping the Twin Picture . . . . . . . . . . . . . . . .24

Selecting a Source for the Twin Picture . . . . . . .24

External Control Device Setup . . . . . . . . . . . . . . . .25~30

IR Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31~32

Troubleshooting Checklist . . . . . . . . . . . . . . . . . . . . . .33

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

Contents

Setup and Operation Checklist

Setup and Operation Checklist (See pages 11~13 for available connection and operational setup options.)

1. Unpack Monitor and all accessories.

2. Connect all external video and audio equipment. see pages 11 ~ 14.

3 Install batteries in remote control.

See page 8.

4. Turn Monitor on. See page 15.

5. Turn video source equipment on.

6. Select viewing source for Monitor. See page 8.

7. Fine-tune source image and sound to personal preference or as required by source. See pages 16 ~ 17.

8. Additional features Setup See Contents above.

6 Plasma Monitor

Introduction

What is a Plasma Display Panel (PDP)?

If voltage is applied to gas within glass panels, ultraviolet rays are produced and fused with a fluorescent substance. At that instant, light is emitted. APlasma Display is a next generation flat Display using this phenomenon.

160° - Wide angle range of vision

Your flat panel plasma screen offers an exceptionally broad viewing angle -- over 160 degrees. This means that the display is clear and visible to viewers anywhere in the room.

Wide Screen

The screen of the Plasma Display is so wide that your viewing experience is as if you are in a theater.

Multimedia

Connect your plasma display to a PC and you can use it for conferencing, games, and internet browsing. The Picture-in-Picture feature allows you to view your PC and video images simultaneously.

Versatile

The light weight and thin size makes it easy to install your plasma display in a variety of locations where conventional TVs would not fit.

The PDP Manufacturing Process: Why minute colored dots may be present on the PDP screen

The PDP (Plasma Display Panel) which is the display device of this product is composed of 0.9 to 2.2 million cells. A few cell defects will normally occur in the PDP manufacturing process. Several minute colored dots visible on the screen should be acceptable. This also occurs in other PDP manufacturers' products and the tiny dots appearing does not mean that this PDP is defective. Thus a few cell defects are not sufficient cause for the PDP to be exchanged or returned. Our production technology is designed to minimize cell defects during the manufacture and operation of this product.

Cooling Fan Noise

In the same way that a fan is used in a PC computer to keep the CPU (Central Processing Unit) cool, the PDP is equipped with cooling fans to cool the Monitor and improve its reliability. Therefore, a certain level of noise could occur while the fans are operating and cooling the PDP. The fan noise doesn't have any negative effect on the PDP's efficiency or reliability. The noise from these fans is normal during the operation of this product. We hope you understand that a certain level of noise from the cooling fans is acceptable and is not sufficient cause for the PDP to be exchanged or returned.

Owner’s Manual 7

Introduction

Controls

Connection Options

( )

RS-232C INPUT

(CONTROL/SERVICE)

EXTERNAL SPEAKER

YPBP

(MONO)

AUDIO

S-VIDEO

AC INPUT

AUDIO INPUTVIDEO INPUT

AUDIO INPUT

REMOTE CONTROL

COMPONENT INPUT

DVI INPUT

RGB INPUT

RGB OUTPUT

1. EXTERNAL SPEAKER (8 ohm output)

Connect to optional external speaker(s). * For further information, refer to ‘Speaker & Speaker

Stand’ manual.

2. RS-232C INPUT (CONTROL/SERVICE) PORT

Connect to the RS-232C port on a PC.

3. DVI (Digital Visual Interface) INPUT/ RGB INPUT/AUDIO INPUT JACKS

Connect the monitor output connector from a PC to the appropriate input port.

4. RGB OUTPUT PORT

You can watch the RGB signal on another monitor, connect RGB OUTPUT to another monitor ’s PC input port.

5. REMOTE CONTROL

Connect your wired remote control to the remote control port on the Monitor.

6. COMPONENT INPUT/AUDIO INPUT JACKS

Connect a component video/audio device to these jacks.

7. S-VIDEO INPUTS

Connect S-Video out from an S-VIDEO VCR to the S-VIDEO input.

AUDIO/VIDEO INPUT JACKS

Connect audio/video out from external equipment to these jacks.

8. POWER CORD SOCKET

This Monitor operates on an AC power. The voltage is indicated on the Specifications page. Never attempt to operate the Monitor on DC power.

Back Connection Panel

VOL.

INPUT SELECT

ON/OFF

Main Power Button

INPUT SELECT Button

VOLUME (F,G) Buttons

Power Standby Indicator

Illuminates red in standby mode,

Illuminates green when the

Monitor is turned on.

Remote Control Sensor

MENU Button

E, D Buttons

Front Panel Controls

2 4 53 7

- This is a simplified representation of front panel.

Here shown may be somewhat different from your monitor.

- Connection panels shown may be somewhat different from your monitor.

8 Plasma Monitor

Introduction

- When using the remote control, aim it at the remote control sensor on the monitor.

- Under certain conditions such as if the remote IR signal is interrupted, the remote control may not function. Press the key again as necessary.

123

456

7809

POWER

SLEEP INPUT SELECT

APC DASP

ARC PIP ARC

PIP

TWIN PICTURE

SWAP

MENU MUTE

VOL

POWER STOP

PLAY FF

REC

REW

P/STILL

WIN.SIZE

WIN.POSITION

ZOOM +

ZOOM -

SPLIT ZOOM

VOL

SUB INPUT

POWER

Switches the Monitor between

ON and STANDBY.

SLEEP

Sets the Sleep Timer.

(Refer to p.18)

APC

Adjusts the factory preset picture

according to the room.

(Refer to p.16)

ARC

Changes the picture format.

(Refer to p.20)

PIP

Switches the sub picture on or off.

(Refer to p.23)

SWAP

Exchanges main and sub picture

images. (Refer to p.23, 24)

Displays on screen menus one by one.

Exits the current menu.

NUMBER buttons

WIN. SIZE

Adjusts the sub picture size.

WIN.POSITION

Moves the sub picture.

SPLIT ZOOM

Enlarges the picture.

ZOOM-/ZOOM+

Enlarges or reduces

the main picture size.

VCR BUTTONS

Control some video cassette recorders.

OK D / E

Selects menu option. Memorizes menu changes.

F / G (Volume button)

Increases/decreases sound level. Adjusts menu settings.

INPUT SELECT

Selects source:

Video, S-Video,

RGB, DVI, or Component mode.

DASP

To select the sound appropriate to your viewing program character:

Flat, Music, Cinema, Sports,or User (Refer to p.17)

PIP ARC

Changes the PIP picture format. (Refer to p.23)

SUB INPUT

Selects the input source for the sub picture.

MUTE

Switches the sound on or off.

TWIN PICTURE

(Refer to p.24)

• Open the battery compartment cover on the back side and insert the batteries with correct polarity.

• Install two 1.5V batteries of AAA type. Don’t mix used batteries with new batteries.

Installing Batteries

Remote Control Key Functions

Owner’s Manual 9

Installation

D-sub 15 pin Cable

Owner’s Manual

1.5V

Batteries

BNC-RCAAdapter

Power Cord

123

456

7809

POWER

SLEEP INPUT SELECT

APC DASP

ARC PIP ARC

PIP

TWIN PICTURE

SWAP

MENU MUTE

VOL

POWER STOP

PLAY FF

REC

REW

P/STILL

WIN.SIZE

WIN.POSITION

ZOOM +

ZOOM -

SPLIT ZOOM

VOL

SUB INPUT

Remote Control

DVI-D Cable

Ensure that the following accessories are included with your plasma display. If an accessory is missing, please contact the dealer where you purchased the product.

Installation Instructions

• The Monitor can be installed in various ways such as on a wall, or on a desktop etc.

• The plasma display is designed to be mounted horizontally or vertically. The speakers shown are optional.

GROUNDING

Ensure that you connect the grounding / earth wire to prevent possible electric shock. If grounding methods are not possible, have a qualified electrician install a separate circuit breaker. Do not try to ground the unit by connecting it to telephone wires, lightening rods, or gas pipes.

Power

Supply

Short-circuit

Breaker

WWall Mount: Horizontal installation

all Mount: Horizontal installation

For proper ventilation, allow a clearance of 4” on each side and 2” from the wall. Detailed installation instructions are available from your dealer, see the optional Wall Mounting Bracket Installation and Setup Guide.

4 inches

4 inches4 inches

4 inches

2 inches

10 Plasma Monitor

Installation

WWall Mount: V

all Mount: V

ertical installation (MU-50PZ44M/44V/90M/90V series models only)

Detailed installation instructions are included in the optional Vertical Wall Mounting Bracket Installation and Setup Guide available from your dealer. NOTE: When installing the monitor vertically, the front panel controls must be in the left side position.

When installing the monitor vertically, you have to change the OSD display mode so that the menus will appear correctly and also to protect the monitor from overheating (Refer to P. 19).

4 inches

2.36 inches

4 inches

2 inches

Desktop Pedestal Installation

For proper ventilation, allow a clearance of 4” on each side and the top, 2.36” on the bottom, and 2” from the wall. Detailed installation instructions are included in the optional Desktop Stand Installation and Setup Guide available from your dealer.

Installation Instructions continued

Owner’s Manual 11

Installation

External Equipment Connections

NOTE: Not all cables shown are included with the plasma display.

- To avoid picture noise (interference), leave an adequate distance between the VCR and Monitor

- Use the ISM Method feature to avoid having a fixed image remain on the screen for a long period of time. Typically a frozen still picture from a VCR. If the 4:3 picture format is used; the fixed image may remain visible on the screen.

How to connect

1. Connect the provided BNC-RCA adapter to the monitor’s VIDEO INPUT.

2. Connect the audio and video cables from the VCR's output jacks to the monitor input jacks, as shown in the figure. When connecting the monitor to VCR, match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red).

Mono VCR: Connect the video output cable from the VCR to the VIDEO input on the monitor.

S-VIDEO VCR: Connect the S-Video output cable from the VCR to the S-VIDEO input on the monitor. (Note that S-Video offers higher quality).

How to use

1. Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner’s manual.)

2. Use the INPUT SELECT button on the remote control to select Video. (If connected to S-VIDEO, select the S-Video input source.)

VCR Setup

S-VIDEO

OUT

(R) AUDIO (L) VIDEO

YPBP

(MONO)

AUDIO

S-VIDEO

AUDIO INPUTVIDEO INPUT

AUDIO INPUT COMPONENT INPUT

- After subscribing to a cable TV service from a local provider and installing a converter, you can watch cable TV programming. The monitor cannot display TV programming unless a TV tuner device or cable TV converter box is connected to the Monitor.

- For further information regarding cable TV service, contact your local cable TV service provider(s).

How to connect

1. Connect the provided BNC-RCA adapter to the monitor’s VIDEO INPUT.

2. Connect the audio and video cables from the Cable Box's output jacks to the monitor input jacks, as shown in the figure. When connecting the monitor to a Cable Box, match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red).

How to use

1. Use the INPUT SELECT button on the remote control to select Video.

2. Select your desired channel with the remote control for cable box.

Cable

TV Setup

VCR

RF Cable

(R) AUDIO (L) VIDEO

YPBP

(MONO)

AUDIO

S-VIDEO

AUDIO INPUTVIDEO INPUT

AUDIO INPUT

COMPONENT INPUT

VCR

Cable Box

+ 25 hidden pages