PLASMA MONITOR
OWNER’S MANUAL
MODELS : MU-42PZ90XV
Please read this owner’s manual thoroughly before operating the Monitor.
Retain it for future reference.
Record model number and serial number of the Monitor. See the label attached on the back of the Monitor and relate this information to your dealer if you ever require service.
Model Number :
Serial Number :
Warning
Warning
WARNING
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING:
TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
FCC NOTICE
•A Class B digital device
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
•Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
WARNING
TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
2 Plasma Monitor
Safety Instructions
Safety Instructions
Important safeguards for you and your new product
Your product has been manufactured and tested with your safety in mind. However, improper use can result in potential electrical shock or fire hazards. To avoid defeating the safeguards that have been built into your new product, please read and observe the following safety points when installing and using your new product, and save them for future reference.
Observing the simple precautions discussed in this booklet can help you get many years of enjoyment and safe operation that are built into your new product.
This product complies with all applicable U.S. Federal safety requirements, and those of the Canadian Standards Association.
1. Read Instructions
All the safety and operating instructions should be read before the product is operated.
9. Attachments
Do not use attachments not recommended by the product manufacturer as they may cause hazards.
2. Follow Instructions
All operating and use instructions should be followed.
3. Retain Instructions
The safety and operating instructions should be retained for future reference.
4. Heed Warnings
All warnings on the product and in the operating instructions should be adhered to.
5. Cleaning
Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
6. Water and Moisture
Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool.
7. Accessories, Carts, and Stands
Do not place this product on a slippery or tilted surface, or on an unstable cart, stand, tripod, bracket, or table. The product may slide or fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer.
8. Transporting Product
A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn.
10. Ventilation
Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.
11. Power Sources
This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions.
12. Power-Cord Polarization
This product is equipped with a three-wire grounding type plug, a plug having a third (grounding) pin. This plug will only fit into the grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug.
13. Power-Cord Protection
Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.
PORTABLE CART WARNING
Owner’s Manual 3
Safety Instructions
Safety Instructions continued
14. Outdoor Antenna Grounding
If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code (U.S.A.), ANSI/ NFPA 70 provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-dis- charge unit, connection to grounding electrodes, and requirements for the grounding electrode.
Example of Grounding According to National Electrical Code Instructions
Ground Clamp
|
|
|
|
Antenna Lead in Wire |
|
|
|
|
|
|
|
|
|
Antenna Discharge Unit |
|
|
|
|
(NEC Section 810-20) |
|
|
|
|
Grounding Conductor |
Electric Service |
|
|
|
(NEC Section 810-21) |
|
|
|
|
|
Equipment |
|
|
|
Ground Clamps |
|
|
|
|
|
|
|
|
|
Power Service Grounding |
|
|
|
|
Electrode System (NEC |
|
|
|
|
Art 250, Part H) |
NEC - National Electrical Code
15. Lightning
For added protection for this product (receiver) during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges.
16. Power Lines
An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.
17. Overloading
Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock.
18. Object and Liquid Entry
Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.
19. Servicing
Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
20. Damage Requiring Service
Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:
a.If the power-supply cord or plug is damaged.
b.If liquid has been spilled, or objects have fallen into the product.
c.If the product has been exposed to rain or water.
d.If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation.
e.If the product has been dropped or the cabinet has been damaged.
f.If the product exhibits a distinct change in performance.
21. Replacement Parts
When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.
22. Safety Check
Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition.
23. Wall or Ceiling Mounting
The product should be mounted to a wall or ceiling only as recommended by the manufacturer. The product may slide or fall, causing serious injury to a child or adult, and serious damage to the product.
24. Heat
The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.
4 Plasma Monitor
Contents
Contents
Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3~4
Introduction
Controls and Connection Options . . . . . . . . . . . .7
Remote Control Key Functions . . . . . . . . . . . . . .8
Installation
Installation Instruction . . . . . . . . . . . . . . . . . . . .9~10
External Equipment Connections . . . . . . . . . .11~14
VCR Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Cable TV Setup . . . . . . . . . . . . . . . . . . . . . . . .11
External A/V Source Setup . . . . . . . . . . . . . . . .12
DVD Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
DTV Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
PC Setup . . . . . . . . . . . . . . . . . . . . . . . . . .13~14
Operation
Turning on the Monitor . . . . . . . . . . . . . . . . . . . . .15
Menu Language Selection . . . . . . . . . . . . . . . . . .15 Video Menu Options
APC (Auto Picture Control) . . . . . . . . . . . . . . . .16 Manual Picture Control . . . . . . . . . . . . . . . . . . .16 Auto Color Temperature Control . . . . . . . . . . . .16 Manual Color Temperature Control . . . . . . . . . .16
Audio Menu Options
DASP (Digital Auto Sound Processing) . . . . . . .17 Manual Sound Control . . . . . . . . . . . . . . . . . . .17 AVL (Auto Volume Leveler) . . . . . . . . . . . . . . . .17
Time Menu Options
Clock Setup . . . . . . . . . . . . . . . . . . . . . . . . . . .18 On/Off Timer Setup . . . . . . . . . . . . . . . . . . . . .18 Auto Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 Sleep Timer . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Special Menu Options
Key Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 ISM Method . . . . . . . . . . . . . . . . . . . . . . . . . . .19 Low power . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 Menu Rotation For Vertical Viewing . . . . . . . . . .19
Screen Menu Options
Auto Adjustment . . . . . . . . . . . . . . . . . . . . . . . .20 Setting Picture Format . . . . . . . . . . . . . . . . . . .20 Picture Size Zoom . . . . . . . . . . . . . . . . . . . . . .20 Split Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 Screen Position . . . . . . . . . . . . . . . . . . . . . . . .21 Manual Configure . . . . . . . . . . . . . . . . . . . . . . .21 Screen Adjustments . . . . . . . . . . . . . . . . . . . . .22 Initializing . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 Selecting VGA mode . . . . . . . . . . . . . . . . . . . . .22 Luminance Noise Reduction . . . . . . . . . . . . . . .22
PIP (Picture-in-Picture) Feature
Watching PIP . . . . . . . . . . . . . . . . . . . . . . . . . .23 PIP Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 PIP Aspect Ratio . . . . . . . . . . . . . . . . . . . . . . . .23 Swapping PIP . . . . . . . . . . . . . . . . . . . . . . . . . .23 Moving PIP . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 Selecting an Input Signal Source for PIP . . . . . .23
Twin Picture Setup Options
Watching Twin Picture . . . . . . . . . . . . . . . . . . . .24 Sub Picture Size Adjustment . . . . . . . . . . . . . . .24 Swapping the Twin Picture . . . . . . . . . . . . . . . .24 Selecting a Source for the Twin Picture . . . . . . .24
External Control Device Setup . . . . . . . . . . . . . . . .25~30
IR Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31~32
Troubleshooting Checklist . . . . . . . . . . . . . . . . . . . . . .33
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Setup and Operation Checklist
Setup and Operation Checklist
(See pages 11~13 for available connection and operational setup options.)
1.Unpack Monitor and all accessories.
2.Connect all external video and audio equipment. see pages 11 ~ 14.
3Install batteries in remote control. See page 8.
4.Turn Monitor on.
See page 15.
5.Turn video source equipment on.
6.Select viewing source for Monitor. See page 8.
7.Fine-tune source image and sound to personal preference or as required by source.
See pages 16 ~ 17.
8.Additional features Setup See Contents above.
After reading this manual, keep it handy for future reference.
Owner’s Manual 5
Introduction
Introduction
What is a Plasma Display Panel (PDP)?
If voltage is applied to gas within glass panels, ultraviolet rays are produced and fused with a fluorescent substance. At that instant, light is emitted. A Plasma Display is a next generation flat Display using this phenomenon.
160° - Wide angle range of vision
Your flat panel plasma screen offers an exceptionally broad viewing angle -- over 160 degrees. This means that the display is clear and visible to viewers anywhere in the room.
Wide Screen
The screen of the Plasma Display is 42" so wide that your viewing experience is as if you are in a theater.
Multimedia
Connect your plasma display to a PC and you can use it for conferencing, games, and internet browsing. The Picture-in-Picture feature allows you to view your PC and video images simultaneously.
Versatile
The light weight and thin size makes it easy to install your plasma display in a variety of locations where conventional TVs would not fit.
The PDP Manufacturing Process: Why minute colored dots may be present on the PDP screen
The PDP (Plasma Display Panel) which is the display device of this product is composed of 0.9 to 2.2 million cells. A few cell defects will normally occur in the PDP manufacturing process. Several minute colored dots visible on the screen should be acceptable. This also occurs in other PDP manufacturers' products and the tiny dots appearing does not mean that this PDP is defective.
Thus a few cell defects are not sufficient cause for the PDP to be exchanged or returned. Our production technology is designed to minimize cell defects during the manufacture and operation of this product.
Cooling Fan Noise
In the same way that a fan is used in a PC computer to keep the CPU (Central Processing Unit) cool, the PDP is equipped with cooling fans to cool the Monitor and improve its reliability. Therefore, a certain level of noise could occur while the fans are operating and cooling the PDP.
The fan noise doesn't have any negative effect on the PDP's efficiency or reliability. The noise from these fans is normal during the operation of this product. We hope you understand that a certain level of noise from the cooling fans is acceptable and is not sufficient cause for the PDP to be exchanged or returned.
WARNING
TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
6 Plasma Monitor
Introduction
Controls
Front Panel Controls
-This is a simplified representation of front panel.
Here shown may be somewhat different from your monitor.
ON/OFF |
|
INPUT |
|
|
|
SELECT |
MENU |
VOL. |
|
Main Power Button |
|
|
|
E, D Buttons |
INPUT SELECT Button |
|
|
||
|
VOLUME (F,G) Buttons |
|||
|
|
|
||
|
Remote Control Sensor |
MENU Button |
||
|
|
|
Power Standby Indicator |
|
|
|
|
|
|
|
|
|
|
Illuminates red in standby mode, |
|
|
|
|
Illuminates green when the |
|
|
|
|
Monitor is turned on |
Connection Options
- Connection panels shown may be somewhat different from your monitor.
( ) R ( ) |
( |
) L ( |
) |
|
|
|
PB |
PR |
|
|
|
R AUDIO L (MONO) |
|
|
|
|
|
|
|
|
|
|
|
||||
EXTERNAL SPEAKER |
RS-232C INPUT |
DVI INPUT |
RGB |
|
|
INPUT |
REMOTE |
S-VIDEO |
VIDEO |
AUDIO INPUT |
AC INPUT |
||
|
|
|
(CONTROL/SERVICE) |
|
|
|
|
|
CONTROL |
|
INPUT |
|
|
|
1 |
|
2 |
|
3 |
4 |
5 |
|
6 |
|
7 |
|
8 |
1.EXTERNAL SPEAKER (8 ohm output)
Connect to optional external speaker(s)
*For further information, refer to ‘Speaker Stand’ manual.
2.RS-232C INPUT (CONTROL/SERVICE)
Connect to the RS-232C port on a PC.
3.DVI (Digital Visual Interface) INPUT/ RGB INPUT/AUDIO INPUT JACKS
Connect the monitor output connector priate input port.
4.RGB OUTPUT JACKS
You can watch the RGB signal on another
RGB OUTPUT to another monitor’s PC input port.
5.COMPONENT INPUT/AUDIO INPUT JACKS
Connect a component video/audio device to these jacks.
remote control to the remote control
.
out from an S-VIDEO VCR to the S-VIDEO
INPUT JACKS
out from external equipment to these
SOCKET
on an AC power. The voltage is indipage. Never attempt to operate
power.
Owner’s Manual 7
Introduction
Remote Control Key Functions
-When using the remote control, aim it at the remote control sensor on the monitor.
-Under certain conditions such as if the remote IR signal is interrupted, the remote control may not function. Press the key again as necessary.
POWER |
|
|
|
|
Switches the Monitor between |
|
|
|
INPUT SELECT |
ON and STANDBY. |
|
|
|
|
|
|
|
Selects source: Video, S-Video, |
|
SLEEP |
|
|
|
|
|
|
|
RGB, DVI, or Component mode. |
|
Sets the Sleep Timer. |
POWER |
|
|
|
(Refer to p.18) |
|
|
|
DASP |
|
SLEEP |
|
INPUT SELECT |
|
APC |
|
To select the sound appropriate to |
||
|
|
|
||
Adjusts the factory preset picture |
APC |
|
DASP |
your viewing program character: |
according to the room. |
ARC |
|
PIP ARC |
Flat, Music, Cinema, Sports, or |
(Refer to p.16) |
PIP |
TWIN PICTURE |
User (Refer to p.17) |
|
|
PIP ARC |
|||
ARC |
SWAP |
|
SUB INPUT |
|
|
Changes the PIP picture format. |
|||
Changes the picture format. |
|
|
|
|
MENU |
|
MUTE |
(Refer to p.23) |
|
(Refer to p.20) |
|
|||
|
|
|
|
|
PIP |
|
|
|
TWIN PICTURE |
Switches the sub picture on or off. |
|
OK |
|
(Refer to p.24) |
(Refer to p.23) |
VOL |
VOL |
|
|
|
|
|||
|
|
|
SUB INPUT |
|
|
|
|
|
|
SWAP |
|
|
|
Selects the input source for the sub |
|
|
|
picture. |
|
Exchanges main and sub picture |
|
|
|
|
|
|
|
|
|
images. (Refer to p.23, 24) |
|
|
|
MUTE |
MENU |
1 |
2 |
3 |
Switches the sound on or off. |
|
||||
Displays on screen menus one by one. |
4 |
5 |
6 |
OK |
Exits the current menu. |
7 |
8 |
9 |
|
|
D / E |
|||
|
|
0 |
|
|
NUMBER buttons |
|
|
Selects menu option. |
|
|
|
|
||
|
|
|
|
Memorizes menu changes. |
WIN. SIZE |
|
|
|
F / G (Volume button) |
|
|
|
Increases/decreases sound level. |
|
Adjusts the sub picture size. |
POWER |
STOP |
P/STILL |
|
|
|
|
Adjusts menu settings. |
|
|
REW |
PLAY |
FF |
|
|
|
|||
WIN.POSITION |
|
|
REC |
|
Moves the sub picture. |
|
|
VCR BUTTONS |
|
|
|
|
||
SPLIT ZOOM |
WIN.SIZE |
WIN.POSITION SPLIT ZOOM |
Control some video cassette |
|
ZOOM - |
ZOOM + |
recorders. |
||
Enlarges the picture. |
|
|||
|
|
|
|
|
ZOOM-/ZOOM+ |
|
|
|
|
Enlarges or reduces |
|
|
|
|
the main picture size. |
|
|
|
|
Installing Batteries
• Open the battery compartment cover on the back side and insert the batteries with correct polarity.
• Install two 1.5V batteries of AAA type. Don’t mix used batteries with new batteries.
8 Plasma Monitor
Installation
Installation
Ensure that the following accessories are included with your plasma display. If an accessory is missing, please contact the dealer where you purchased the product.
|
1.5V |
|
|
Owner’s Manual |
Batteries |
BNC-RCA Adapter |
Remote Control |
|
|
|
|
|
|
|
|
|
|
|
|
|
DVI-D Cable |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
D-sub 15 pin Cable |
Power Cord |
|
|
Installation Instructions
•The Monitor can be installed in various ways such as on a wall, or on a desktop etc.
•The plasma display is designed to be mounted horizontally or vertically. The speakers depicted are optional.
GROUNDING
Ensure that you connect the grounding / earth wire to prevent possible electric shock. If grounding methods are not possible, have a qualified electrician install a separate circuit breaker. Do not try to ground the unit by connecting it to telephone wires, lightening rods, or gas pipes.
Power
Supply
Short-circuit
Breaker
Wall Mount: Horizontal installation
yyyyy;;;;;
;;;;;yyyyy |
;;;;;yyyyy |
For proper ventilation, allow a clearance of 4” on each side and 2” from the wall. Detailed installation instructions are included from your dealer in the optional Wall
Mounting Bracket Installation and Setup Guide.
|
4 inches |
2 inches |
|
|
|
4 inches |
|
4 inches |
|
4 inches |
|
Owner’s Manual 9
Installation
Installation Instructions continued
Desktop Pedestal Installation
For proper ventilation, allow a clearance of 4” on each side and the top, 2.36” on the bottom, and 2” from the wall. Detailed installation instructions are included in the optional Desktop Stand Installation and Setup Guide, see your dealer.
|
|
2 inches |
||
|
4 inches |
|
|
|
|
|
|
|
|
4 inches |
4 inches |
2.36 inches |
Detailed installation instructions are included in the optional Vertical Wall Mounting Bracket Installation and Setup Guide, see your dealer.
NOTE: When installing the monitor vertically, the front panel controls must be in the left side position.
When installing the monitor vertically, you have to change the OSD display mode so that the menus will appear correctly and also to protect the monitor from overheating (Refer to P. 19).
10 Plasma Monitor
Installation
External Equipment Connections
NOTE: All cables shown are not included with the plasma display.
VCR Setup
noise (interference), leave an adequate distance between the VCR and Monitor
feature to avoid having a fixed image remain on the screen for a long period of time. Typically a frozen still
. If the 4:3 picture format is used; the fixed image may remain visible on the screen.
BNC-RCA adapter to the monitor’s
and video cables from the VCR's output input jacks, as shown in the figure. When
monitor to a VCR, match the jack colors: (Video = white, and Audio Right = red).
video output cable from the VCR to the monitor.
Connect the S-Video output cable from the input. (Note that S-Video yields higher
into the VCR and press PLAY on the VCR. owner’s manual.)
SELECT button on the remote control to select
VIDEO, select the S-Video external input
R AUDIO L |
Y |
PB |
PR |
|
|
|
R AUDIO L (MONO) |
AUDIO INPUT |
COMPONENT INPUT |
REMOTE |
S-VIDEO |
VIDEO |
AUDIO INPUT |
||
|
|
|
|
CONTROL |
|
INPUT |
|
S-VIDEO |
OUT |
(R) AUDIO (L) |
VIDEO |
IN |
VCR
Cable TV Setup
TV service from a local provider and installing a converter, you can watch cable TV programming. TV programming unless a TV tuner device or cable TV converter box is connected to the Monitor.
cable TV service, contact your local cable TV service provider(s).
-RCA adapter to the monitor’s
cables from the cable box's outinput jacks, as shown in the figure.
to a cable TV, match the jack Left = white, and Audio Right =
R AUDIO L |
Y |
PB |
PR |
|
|
|
R AUDIO L (MONO) |
AUDIO INPUT |
COMPONENT INPUT |
REMOTE |
S-VIDEO |
VIDEO |
AUDIO INPUT |
||
|
|
|
|
CONTROL |
|
INPUT |
|
button on the remote control to
with the cable box remote control.
(R) AUDIO (L) |
VIDEO |
TV |
|
VCR |
RF Cable |
Cable Box
Owner’s Manual 11