LG MG100 Service Manual

B2050Cover_3.3-0419 2005.4.20 1:7 PM Page 2

launaM ecivreS

Service Manual

edoM MG100
: l

MG100

P/N : MMBD0049101 Date : April 2005 / Issue 1.0

Table Of Contents

1. INTRODUCTION..........................2

1.1 Purpose ...........................................2

1.2 Regulatory Information ....................2

1.3 Abbreviations ..................................4

2. PERFORMANCE ........................ 6

2.1 H/W Feature ...................................6

2.2 Technical Specification ..................8

3. TECHNICAL BRIEF ..................13

3.1 Transceiver ...................................13

3.2 Power Amplifier Module ..................19

3.3 13 MHz Clock ............................... 20

3.4 Power Supplies of RF circuits ........20

Digital Main Processor..................22

3.6 Analog Main & Power

Management Processor ................28

3.7 Display Interface ............................. 38

3.8 Keypad Switches and Scanning .... 41

3.9 Microphone ....................................42

3.10 Main Speaker ............................. 42

3.11 Headset interface ........................43

3.12 Key Back-light Illumination .......... 44

3.13 Vibrator ........................................45

4. TROUBLE SHOOTING ............. 46

4.1 RX Trouble ................................... 46

4.2 TX Trouble ................................... 53

4.3 Power On Trouble .........................61

4.4 Charging Trouble........................... 63

4.5 Vibrator Trouble..............................65

4.6 LCD Trouble.................................. 67

4.7 Speaker Trouble.............................71

4.8 SIM card interface trouble ............ 74

4.9 Earphone Trouble...........................76

4.10 Key Backlight Trouble ..................78

4.11 Receiver Trouble...........................80

4.12 Microphone Trouble .................... 82

4.13 RTC Trouble .................................84

4.14 Indication LED Trouble..................86

5. DOWNLOAD AND

CALIBRATION .......................88

5.1 Download .......................................88

5.2 Calibration .......................................93

6. BLOCK DIAGRAM.....................94

7. CIRCUIT DIAGRAM ...................97

8. PCB LAYOUT .........................102

9. ENGINEERING MODE .............105

9.1 BB Test [MENU 1].........................106

9.2 RF Test [MENU 2].........................107

9.3 MF mode [MENU 3] ......................108

9.4 Trace option [MENU 4]..................109

9.5 Call timer [MENU 5]......................109

9.6 Fact. Reset [MENU 6] ...................109

9.7 S/W version [MENU 7] ..................109

10. STAND ALONE TEST.............110

10.1 Introduction ...............................110

10.2 Setting Method............................110

10.3 Means of Test ............................111

12. AUTO CALIBRATION ...........113

11.1 Overview.....................................113

11.2 Requirements..............................113

11.3 Menu and Settings ......................113

11.4 AGC............................................115

11.5 APC............................................115

11.6 ADC............................................115

11.7 Setting........................................115

11.8 How to do calibration...................115

12. EXPLODED VIEW &

REPLACEMENT PART LIST...117

12.1 Exploded View ............................117

12.2 Replacement Parts

<Mechanic component>...............119

<Main component>......................120

12.3 Accessory ....................................130

- 2 -

1. INTRODUCTION

1. INTRODUCTION

1.1 Purpose

This manual provides the information necessary to repair, calibration, description and download the
features of this model.

1.2 Regulatory Information

A. Security

To ll fraud, the unauthorized use of telecommunications system byan unauthorized part (for
example, persons other than your company’s employees, agents, subcontractors, or person
working on your company’s behalf) can result in substantial additional charges for your telecom­munications services. System users are responsible for the security of own system. There are
may be risks of toll fraud associated with your telecommunications system. System users are
responsible for programming and configuring the equipment to prevent unauthorized use. The
manufacturer does not warrant that this product is immune from the above case but will prevent
unauthorized use of common-carrier telecommunication service of facilities accessed throughor
connected to it.

The manufacturer will not be responsible for any charges that result from such unauthorized use.

B. Incidence of Harm

If a telephone company determines that the equipment provided tocustomer is faulty and possi­bly causing harm or interruption in service to the telephone network, it should disconnect tele­phone service until repair can be done. A telephone company may temporarily disconnect ser­vice as long as repair is not done.

C. Changes in Service

Alocal telephone company may make changes in its communicationsfacilities or procedure. If
these changes could reasonably be expected to affect the use of the this phone or compatibility
with the network, the telephone company is required to give advanced written notice to the user,
allowing the user to take appropriate steps to maintain telephone service.

D. Maintenance Limitations

Maintenance limitations on this model must be performed only by the manufacturer or its autho­rized agent. The user may not make any changes and/or repairs expect as specifically noted in
this manual. Therefore, note that unauthorized alternations or repair may affect the regulatory
status of the system and may void any remaining warranty.

- 3 -

1. INTRODUCTION

E. Notice of Radiated Emissions

This model complies with rules regarding radiation and radio frequency emission as defined by
local regulatory agencies. In accordance with these agencies, you may be required to provide
information such as the following to the end user.

F. Pictures

The pictures in this manual are for illustrative purposes only; your actual hardware may look
slightly different.

G. Interference and Attenuation

Phone may interfere with sensitive laboratory equipment, medical equipment, etc.Interference
from unsuppressed engines or electric motors may cause problems.

H. Electrostatic Sensitive Devices

ATTENTION

Boards, which contain Electrostatic Sensitive Device (ESD), are indicated by the sign.
Following information is ESD handling:

•Service personnel should ground themselves by using a wrist strap when exchange
systemboards.

•When repairs are made to a system board, they should spread thefloor with anti-static mat
which is also grounded.

•Use a suitable, grounded soldering iron.

•Keep sensitive parts in these protective packages until these are used.

•When returning system boards or parts like EEPROM to the factory, use the protective
package as described.

- 4 -

1. INTRODUCTION

1.3 Abbreviations

For the purposes of this manual, following abbreviations apply:

APC Automatic Power Control

BB Baseband

BER Bit Error Ratio

CC-CV Constant Current – Constant Voltage

DAC Digital to Analog Converter

DCS Digital Communication System

dBm dB relative to 1 milli watt

DSP Digital Signal Processing

EEPROM Electrical Erasable Programmable Read-Only Memory

ESD Electrostatic Discharge

FPCB Flexible Printed Circuit Board

GMSK Gaussian Minimum Shift Keying

GPIB General Purpose Interface Bus

GSM Global System for Mobile Communications

IPUI International Portable User Identity

IF Intermediate Frequency

LCD Liquid Crystal Display

LDO Low Drop Output

LED Light Emitting Diode

OPLL Offset Phase Locked Loop

- 5 -

1. INTRODUCTION

SIM Subscriber Identity Module

SLR Sending Loudness Rating

SRAM Static Random Access Memory

PSRAM Pseudo SRAM

STMR Side Tone Masking Rating

TA Travel Adapter

TDD Time Division Duplex

TDMA Time Division Multiple Access

UART Universal Asynchronous Receiver/Transmitter

VCO Voltage Controlled Oscillator

VCTCXO Voltage Control Temperature Compensated Crystal Oscillator

WAP Wireless Application Protocol

SAW Surface Acoustic Wave

PAM Power Amplifier Module

PCB Printed Circuit Board

PGA Programmable Gain Amplifier

PLL Phase Locked Loop

PSTN Public Switched Telephone Network

RF Radio Frequency

RLR Receiving Loudness Rating

RMS Root Mean Square

RTC Real Time Clock

- 6 -

2. PERFORMANCE

2. PERFORMANCE

2.1 H/W Features

- 7 -

2. PERFORMANCE

- 8 -

2. PERFORMANCE

2.2 Technical Specification

- 9 -

2. PERFORMANCE

- 10 -

2. PERFORMANCE

- 11 -

2. PERFORMANCE

- 12 -

2. PERFORMANCE

3. TECHNICAL BRIEF

- 13 -

3. TECHNICAL BRIEF

3.1 Transceiver (SI4205-BM, U500)

The RF parts consist of a transmitter part, a receiver part, a frequency synthesizer part, a voltagesup­ply part, and a VCTCXO part.

The Aero I transceiver is the integrated RF front end for multi-band GSM/GPRS digital cellularhand­sets and wireless data modems. The integrated solution eliminates the IF SAW filter, externallow
noise amplifier (LNAs) for three bands, transmit and RF voltage controlled oscillator(VCOmodules,
and other discrete components found in conventional designs.

Figure 3-1 RECEIVER FUNCTIONAL BLOCK DIAGRAM

HCTIWS ANNETNA

TCXO

3. TECHNICAL BRIEF

- 14 -

(1) Receiver Part

The Aero I transceiver uses a low-IF receiver architecture which allows for the onchip integration of
the channel selection filters, eliminating the external RF imagereject filters and the IF SAW filter
required in conventional super-heterodynearchitectures.

A. RF front end

RF front end consists of Front End Module(FL500) and Quad bandLNAsintegrated in transceiver
(U500).
The Received RF signals(GSM 925MHz ~ 960MHz, DCS 1805MHz ~ 1880MHzPCS 1930MHz ~
1990MHz) are fed into the antenna or Mobile switch. The Front End Module(FL500) is used to
control the Rx and Tx paths. And, the inputsignals VC1, VC2, VC3 of a FL501 are directly con­nected to basebandcontroller to switch either Tx or Rx path on.
The logic and current is given below Table 3-1.

Three differential-input LNAsare integrated in SI4205. The GSM input supports the GSM850
(869-849 MHz) or E-GSM 900 (925-960MHz) bands. The DCS input supports theDCS 1800
(1805-1880 MHz) band. The PCS input supports the PCS 1900 (1930-1990MHz) band.
The LNA inputs are matched to the 150Ωbalanced output SAW filters through externalLC match­ing networks. The LNA gain is controlled with the LNAG[1:0] and LNAC[1:0]bits in register 05h
(Figure 3-2).

VC1 VC2 VC3

GSM Tx

DCS, PCS Tx

GSM / DCS Rx

PCS / DCS Rx

0 V

0 V

0 V

2.5 ~ 3.0 V

Table 3-1 THE LOGIC AND CURRENT

0 V

2.5 ~ 3.0 V

0 V

0 V

2.5 ~ 3.0 V

0 V

0 V

0 V

3. TECHNICAL BRIEF

- 15 -

Figure 3-2 SI4205 RECEIVER PART

B. Intermediate frequency (IF) and Demodulation

A quadrature image-reject mixer downconvertsthe RF signal to a 100KHz intermediate frequency
(IF) with the RFLO from the frequency synthesizer. The RFLO frequency is between 1737.8 to

1989.9 MHz, and is internally divided by 2 for GSM 850 and E-GSM 900 modes. The mixer out-

put is amplified with an analog programmable gain amplifier (PGA), which is controlled with the
AGAIN[2:0] bits in register 05h (Figure3-2). The quadratureIF signal is digitized with high resolu­tion A/D converters (ADCs).

The ADC output is downconverted to baseband with a digital 100KHz quadrature LO signal.
Digital decimation and IIR filters perform channel selection to remove blocking and reference
interference signals. The selectivity setting (CSEL=0) or a low selectivity setting (CSEL=1). The
low selectivity filter has a flatter group channelization filter is in the baseband chip. After channel
selection, the digital output is scaled with a digital PGA, which is controlled with the DGAIN [5:0]
bits in register 05h.

The amplified digital output signal go through with DACs that drive a differential analog signal
onto the RXIP,RXIN,RXQP and RXQN pins to interfaceto standard analog ADC input baseband
baseband ICs. No special processing is required in the baseband for offset compensation or
extended dynamic range.

Compared to a direct-conversion architecture, the low-IF architecture has a much greater degree
of immunity to dc offsets that can arise from RF local oscillator(RFLO) self-mixing, 2nd order dis­tortion of blockers, and device 1/f noise.

3. TECHNICAL BRIEF

- 16 -

(2) Transmitter Part

The transmit (Tx) section consists of an I/Q baseband upconverter, and offset phase-locked loop
(OPLL) and two output buffers that can drive external poweramplifiers (PA), one for the GSM 850
(824-849 MHz) and E-GSM 900 (880-915 MHz) bands and one for the DCS 1800 (1710-1785
MHz) and PCS 1900 (1850-1910MHz) bands.

A. IF Modulator

The basebandconverter(BBC) within the GSM chipset generates I and Q baseband signals for
the Transmit vector modulator. The modulator provides more than 40dBc of carrier and unwant­ed sideband rejection and produces a GMSK modulated signal. The baseband software is able
to cancel out differential DC offsets in the I/Q baseband signals caused by imperfections in the
D/A converters.

The Tx-Modulator implements a quadrature modulator. A quadrature mixer upconverts the dif­ferential in-phase (TXIP, TXIN) and quadrature(TXQP, TXQN) signals with the IFLO to generate
a SSB IF signal that is filtered and used as the reference input to the OPLL.

The IFLO frequency is generated between 766 and 896 MHz and internally divided by 2 to gen­erate the quadrature LO signals for the quadrature modulator, resulting in an IF between 383
and 448 MHz. For the E-GSM 900 band, two different IFLO frequencies are required for spur
management. Therefore, the IF PLL must be programmed per channel in the E-GSM 900 band.

PA

RFOG

RFOG

GSM PA

DCS/PCS

Figure 3-3 SI4205 TRANSMITTER PART

3. TECHNICAL BRIEF

- 17 -

B. OPLL

The OPLL consists of a feedback mixer, a phase detector, a loop filter, and a fully integrated

TXVCO. The TXVCO is centered between the DCS 1800 and PCS 1900 bands, and its output is
divided by 2 for the GSM 850 and E-GSM 900 bands. The RFLO frequency is generated
between 1272 and 1483 MHz. To allow a single VCO to be used for the RFLO, high-side injec­tion is used for the GSM 850 and E-GSM 900 bands, and low-side injection is used for the DCS
1800 and PCS 1900 bands. The I and Q signals are automatically swapped when switching
bands. Additionally, the SWAP bit in register 03h can be used to manually exchange the I and
Qsignals.

Low-pass filters before the OPLL phase detector reduce the harmonic content of the quadra-

turemodulator and feedback mixer outputs. The cutoff frequency of the filters is programmable
with the FIF[3:0] bits in register 04h (Figure 3-3), and should be set to the recommended settings
detailed in the register description.

3. TECHNICAL BRIEF

- 18 -

Figure 3-4 SI4205 FREQUENCY SYNTHESIZER PART

The Aero I transceiver integrates two complete PLLs including VCOs, varactors, resonators, loop
filters, reference and VCO dividers, and phase detectors. The RF PLL uses two multiplexed VCOs.
The RF1 VCO is used for receive mode, and the RF2 VCO is used for transmit mode. The IF PLL
is used only during transmit mode. All VCO tuning inductors are also integrated. The IF and RF out­put frequencies are set by programming the N-Divider registers, NRF1, NRF2and NIF.
Programming the N-Divider register for either RF1 or RF2 automatically selects theproper VCO.
The output frequency of each PLL is as follows:

The DIV2 bit in register 31h controls a programmable divider at the XIN pin to allow either a 13 or
26 MHz reference frequency. For receive mode, the RF1 PLL phase detector update rate (

ƒ

ø

)

should be programmed

ƒ

ø

= 100 kHz for DCS 1800 or PCS 1900 bands, and

ƒ

ø

= 200 kHz for GSM
850 and E-GSM 900 bands. For transmit mode, the RF2 and IF PLL phase detector update rates
are always

ƒ

ø

=200 kHz.

(3) Frequency Synthesizer

3. TECHNICAL BRIEF

- 19 -

3.2 Power Amplifier Module (RF3166, U501)

The RF3166 is a high-power, high-efficiency power amplifier module with integrated power
control that provides over 50dB of control range. The device is a self-contained 6mmx6mm
module with 50Ω input and output terminals.
The device is designed for use as the final RF amplifier in GSM850, EGSM900, DCS and PCS
handheld digital cellular equipment and other applications in the 824MHz to 849MHz, 880MHz to
915MHz, 1710MHz to 1785MHz and 1850MHz to 1910MHz bands. The RF3166 incorporates
RFMD’s latest VBATT tracking circuit, which monitors battery voltage and prevents the power
control loop From reaching saturation. The VBATT tracking circuit eliminates the need to monitor
battery voltage, thereby minimizing switching transients. The RF3166 requires no external routing
or external components, simplifying layout and reducing board space.

DCS/PCS

BAND SELECT

TX ENABLE

VBATT

VRAMP

RFIN

GND

GSM
RFIN

1

2

3

4

5

6

7

Figure 3-5 FUNCTIONAL BLOCK DIAGRAM

DCS/PCS

9

RFOUT

GSM

8

RFOUT

3. TECHNICAL BRIEF

- 20 -

3.3 13 MHz Clock (VCTCXO, X500)

The 13 MHz clock(X500) consists of a TCXO(Temperature Compensated Crystal Oscillator) which
oscillates at a frequency of 13 MHz. It is used within the Si4205, analog base band chipset (U101,
AD6537B), digital base band chipset (U100, AD6527).

3.4 Power Supplies for RF Circuits (RF LDO, U702)

Two regulators are used for RF circuits. One is MIC5255 (U702), and the other is one port of
AD6537B (U101).

MIC5255 (U702) supplies power to transceiver (SI4205, U500). One port of AD6537B supplies
power to VCTCXO (X500).

2V75_VVCXO

100

R514

C536
22u

3

OUT VCONT

4

VCC

X500

ONG

13MHz

1

2

C538
1000p

R516

15K

APC

Figure 3-6 VCTCXO CIRCUIT DIAGRAM

Supplier

Voltage

Powers

enabled signal

U702(VRF)

U101(VVCXO)

Battery(VBAT)

2.85 V

2.75 V

3.4 ~ 4.2 V

U501, U702

Table 3-2 RF POWER SUPPLIERS

U500

X500

3. TECHNICAL BRIEF

- 21 -

CLKON

VBAT

U702 MIC5255-85BM5

1

IN

2

GNO

3

EN

OUT

BYP

5

4

RF2VBS

C533

10u

C734 C534

Table 3-7 RF LDO CIRCUIT DIAGRAM

10u0.01u

(1608)

3. TECHNICAL BRIEF

- 22 -

3.5 Digital Main Processor (AD6527, U100)

AD6527/AD6527B GSM-PROCESSOR

Keypad

Matrix

KEYPADCOL[7:0]
KEYPADROW[7:0]

TCK, TMS

JTAGEN

JTAG

TDI, TDO

Backlight/

Service Light

Flash
16-bit

SRAM

8 or 16 bit

(optional)

DISPLAY
(Parallel)

serial display

Accessory

Devices

e.g

BATTERY

SIM

Application

Processor

USB Host

BACKLIGHT[3.0]

Servicelight

JTAG, HSL, GPIO

USCTX/RX/CLK

Enhaoced Generic serial port A

ROMCS[1:0]

ADD[24:0]

DATA[15:0]

RAMCS[1:0]

RD
WR
HWR/UBS
LWR /LBS

Generic serial port B
Generic serial port D

PWRON

RESET

OSCIN

OSCOUT

VDDRTC

VMEM

VEXT

DISPLAYCS[1:0]

Generic Serial
Port C

GPCS[1:0]

AUXCS[1:0]

Generic Serial Port D-A

Generic Serial Port D-B

GPIO[ ] / IRQ

SIM serial
Interface

SPI

USB Interface
*(AD6527B only)

CLKIN

CLKOUT_GATE

MicroSM
RF Interface

VCC

VMMC

VINT

VDDUSB

VSIM

GND

ASDO

ASFS

ASDI

BSDO

BSOFS

BSDI

BSIFS

CSDO
CSDI
CSFS

ABB_INT

CLKOUT

ABBRESET

USC

Management

32KHz

ASDI
ASFS
ASDO

BSDI
BSIFS
BSDO
BSOFS

CSDI
CSDO
CSFS

INT

MCLKEN
MCLK

RESET
VCXOEN

Universal

System

Connector

(USC)

Power

Processor

AD6535 Audio & Base band

Audio

Data

Port

BASE

BAND

I/Q

Serial

Port

control

serial

port

RAMP
RF Timing
I/Q Interface
VOICE i/f &
Buzzer

VOSC
AFC

JTAG

PA S u pply

Enable

DRV-OUT

LNA IN

RADIO
AD6534

AGC Synthesizer

VCO

13/

26MHz

Figure 3-8 SYSTEM INTERCONNECTION OF AD6527 EXTERNAL INTERFACE

3. TECHNICAL BRIEF

- 23 -

• AD6527 is an ADI designed processor

• AD6527 consists of

1. Control Processor Subsystem

• 32-bit ARM7TDMI Control Processor

• 58.5 MHz operation at 1.7V

• On-board 16KB instruction/Data Cache

• 1 Mbitsof on-chip System SRAM

2. DSP Subsystem

• 16-bit Fixed Point DSP Processor

• 91 MIPS at 1.7V

• 16K word Data and 16K word Program SRAM

• 4K word Program Instruction Cache

• Architecture supports Full Rate, Enhanced Full Rate, Half Rate,and AMR speech
Encoding/Decoding Algorithms

3. Peripheral Subsystem

• Shared on-chip peripheral and off-chip interface:

• Support for Burst and Page Mode Flash

• Support for Pseudo SRAM

• Ciphering module for GPRS supporting GAE1 and GAE2 encryption algorithms

• Parallel and Serial Display Interface

• 8 x 8 Keypad Interface

• Four independent programmable backlight plus One Service Light

• 1.8V and 3.0V, 64 kbps SIM interface

• Universal System Connector Interface

• Slow, Medium and Fast IrDA transceiver interface

• Enhanced Generic Serial Port

• Dedicated SPI interface

• Thumbwheel Interface

• JTAG Interface for Test and In-Circuit Emulation

4. Other

• Supports 13 MHz and 26 MHz Input Clocks

• 1.8V Typical Core Operating Voltages

• 204-Ball LFBGA(mini-BGA) Package

5. Applications

• GSM900/DCS1800/PCS1900/PCS850 Wireless Terminals

• GSM Phase 2+ Compliant

• GPRS Class 12 Compliant

• Multimedia Services(MMS)

• Extended Messaging System(EMS)

3. TECHNICAL BRIEF

- 24 -

3.5.1 Interconnection with external devices

A. RTC block interface

Countered by external X-TALThe X-TAL oscillates 32.768KHz

B. LCD module interface

The LCD module is controlled by AD6527(U100),DBB.In operating mode, the AD6527(U100)
controls the LCD module through _LCD_CS, LCD_DIM_CTRL, LCD_RESET, _WR,
2V8_VMEM, LCD_ID, LCD_BL_EN.

Signals

_LCD_CS

LCD_DIM_CTRL

LCD_RESET
(GPIO 15)

_WR

2V8_VMEM

LCD_ID
(GPIO 16)

LCD_BL_EN

Description

MAIN LCD driver chip enable. MAIN LCD driver IC has own CS pin

It controls dimming mode of LCD module. (GPIO_5)

This pin resets LCD module. This signal comes from DBB directly

Enable writing to LCD Driver.

2.8V voltage is supplied to LCD driver IC

It determines the maker of LCD module.

It controls back-light of LCD module. (GPO_23)

Table 3-3 LCD CONTRON SIGNALS DISCRIPTION

3. TECHNICAL BRIEF

- 25 -

The backlight of LCD module is controlled by DBB via TPS60230RGTR , U400. The control signals
related to Backlight LED are given bellow.

Signals Description

LCD_DIM_CTL
(GPO 5)

LCD_LED_CTL

LCD_LED_GND

LCD_BL_EN

Control LCD backlight level in 16 steps

Control LCD LED

It Controls back-light of LCD module. (GPO_223)

Table 3-4 DESCRIPTION OF LCD BACKLIGHT LED CONTROL

C. RF interface

The AD6527 control RF parts through PA_BAND, ANT_SW1, ANT_SW2, ANT_SW2 , CLKON
, PA_EN, S_EN, S_DATA, S_CLK, RF_PWR_DWN.

Signal Description

PA_BAND (GPO 17) PAM Band Select

ANT_SW3 (GPO 11) Antenna switch Band Select

PA_EN (GPO 16) PAM Enable/Disable

S_DATA (GPO 20) Serial Data to PLL

S_CLK (GPO 21) Clock to PLL

S_EN (GPO 19) PLL Enable/Disable

RF_PWR_DWN(GPO 4) Power down Input

ANT_SW1 (GPO 9) Antenna switch Band Select

ANT_SW2 (GPO 10) Antenna switch Band Select

CLKON RF LDO Enable/Disable

Table 3-5 RF CONTRON SIGNALS DISCRIPTION

3. TECHNICAL BRIEF

- 26 -

D. SIM interface

The AD6527 provides SIM Interface Module. The AD6527 checks status periodically during
established call mode whether SIM card is inserted or not, but it doesn't check during
deepSleep mode. In order to communicate with SIM card, 3 signals SIM_DATA,
SIM_CLK,SIM_RST(GPIO_23)
are required. The descriptions about the signals are given by bellow Table 3-6 in detail.

E. Key interface

Include 5 column, 5 row and additional GPIO 35 for KEY_ROW5. The AD6527 detects
whether key is pressed or not by using interrupt method.

F. AD6537B Interrupt

AD6537B provides an active-high interrupt output signal. Interrupt signals are generated by
the Auxiliary ADC, audio, and charger modules.

Signals Description

LCD_DATA

LCD_CLK

SIM_RST
(GPIO_23)

This pin receives and sends data to SIM card.
This model can support only 3.0 volt interface SIM card.

Clock 3.25MHz frequency.

Reset SIM block

Table 3-6 SIM CONTRON SIGNALS DISCRIPTION

J300

VCC
RST

CLK
OND2

OND3

2V85_VSIM

1
2
3
7
8

C315C314

R338

C316 C317
1000p

SIM_DATA

2V85_VSIM

R336

20K

R337

0

NA

4

OND1

5

VPP

6

IO

10

OND5

9

OND4

SIM_RST

0

SIM_CLK

NA220n

Figure 3-9 SIM Interface of AD6527

3. TECHNICAL BRIEF

- 27 -

Figure 3-10 AD6527 ARCHITECTURE

AD6527/AD6527B

AD6535

Audio Baseband

and Power

Management

DSP

SRAM

FLASH

MMI

USC

Peripheral

RF-Control

Subsystem

Subsystem

Subsystem

(ARM7TDMI

®

)

DMA and BUS

ARBITRATION

Serial Link

DSP BUS

RBUS IM

EBUS

PBUS

SBUS

MUC

The internal architecture of AD6527 is shown above Figure 3-10. AD6527 regroups three main subsys­tems connected together through a dynamic and flexible communication bus network. It alsoincludes
onboard system RAM (SRAM) and interfaces with external Flash Memory, Basebandconverter functions,
and terminal functions like MMI, SIM and Universal System Connector (USC).The Digital Signal
Processing (DSP) subsystem primarily hosts all the speech processing, channel equalization and channel
codec functions. The code used to implement such functions can be storedin external Flash Memory and
dynamically downloaded on demand into the DSP’sprogram RAM andInstruction Cache.

The micro-controller subsystem supports all the GSM terminal software, including the layer 1, 2 and 3of
the GSM protocol stack, the MMI, and applications software such as data services, test and mainte­nance. It is tightly associated with on-chip system SRAM and also includes boot ROM memory with a
small dedicated routine to facilitate the initialization of the external Flash Memory via code download
using the on-chip serial interface to the external Flash Memory interface.The peripheral subsystem is
composed of system peripherals such as interrupt controller, real timeclock, watch dog timer, power man­agement and a timing and control module. It also includes peripheral interfaces to the terminal functions:
keyboard, battery supervision, radio and display. Boththe DSP and the MCU can access the peripheral
subsystem via the peripheral bus (PBUS).For program and data storage, both the MCU subsystem and
the DSPsubsystem can access the onchip system SRAM and external memory such Flash Memory. The
access to the SRAM module ismade through the RAM Bus (RBUS) under the control of the bus arbitra­tion logic. Similarly, access tothe Flash Memory is through the parallel External Bus (EBUS).

3. TECHNICAL BRIEF

- 28 -

3.6 Analog Main & Power Management Processor (AD6537B, U101)

AD6525

or

AD6526

AD6537B

TROPSC

TROP

S
B

T
R
O
PSA

Light

Controllers

Ram

GMSK

Filter

Filter

Filter

Tone

DAC

ADC

DAC

DAC

DAC

DAC

ADC

ADC

LEDs

Othello

Crystal &

Var act or

hctiwS

Headphones

or Headset

Battery

Charger

VCORE: 1.8 V, 80mA

VMEM: 1.8 or 2.8V, 150mA

VEXT: 2.8V, 170mA

VSIM: 1.8 or 2.85V, 20mA

VRTC: 1.8V, 200 µA

Figure 3-11 AD6537B FUNCTION BLOCK DIAGRAM

Filter

ADC

8 Voltage Regulators

Mic

VAB B

VMIC: 2.5V, 1mA

VVCXO: 2.75V, 10mA

3. TECHNICAL BRIEF

- 29 -

• AD6537B is an ADI designed Analog Baseband processor. AD6537B covers the processing

GMSK modulation interface, Aux ADC, Voice signal processing and Power Management.

• AD6537B consists of

1. BB Transmit section

• GMSK Modulation

• I-channel & Q-channel Transmit DACs and Filters

• Power Ramping DAC

2. BB Receive section

• I-channel & Q-channel Receive ADCs and Filters

3. Auxiliary section

• Voltage Reference

• Automatic Frequency Control DAC

• Auxiliary ADC

• Light Controllers

4. Audio Section

• 8 kHz & 16 kHz Voiceband Codec

• 48 kHz Monophonic DAC

• Power Amplifiers

5. Power Management section

• Voltage Regulators

• Battery Charger

• Battery Protection6. Digital Processor section

• Control, Baseband, and Audio Serial Ports

• Interrupt Logic