OWNER'S MANUAL
AIR
GAEILGE
SRPSKI
ENGLISH ITALIANO
ESPAÑOL FRANÇAIS
EESTI KEEL
DEUTSCH
MALTIHRVATSKI
CONDITIONER
Read this owner's manual thoroughly before operating the appliance and
keep it handy for reference at all times.
the original manual from www.lg.com.
TYPE : WALL MOUNTED
Original instruction
[Representative] LG Electronics Inc. EU Representative :
LG Electronics European Shared Service Center B.V.
Krijgsman 1, 1186 DM Amstelveen, The Netherlands
[Manufacturer] LG Electronics Inc. Changwon 2nd factory 84, Wanam-ro,
Seongsan-gu, Changwon-si, Gyeongsangnam-do, KOREA
ROMÂNÂ
PORTUGUÊS NEDERLANDS
POLSKI
MAGYAR
MFL67870337
Rev.00_052818
www.lg.com
Copyright © 2018 LG Electronics Inc. All Rights Reserved.
TABLE OF CONTENTS
SAFETY INSTRUCTIONS ....................................... 3
IMPORTANT SAFETY INSTRUCTIONS ................................................. 4
OPERATION ............................................................. 9
Notes for Operation ................................................................................. 9
Parts and Functions................................................................................. 9
Wireless Remote Control....................................................................... 10
This manual is produced for a group of products
and may contain images or content different from
the model you purchased.
This manual is subject to revision by the
manufacturer.
SAFETY INSTRUCTIONS
The following safety guidelines are intended to prevent unforeseen risks or
damage from unsafe or incorrect operation of the appliance.
The guidelines are separated into ‘WARNING’ and ‘CAUTION’ as described
below.
This symbol is displayed to the indicate matters and operations that
can cause risk. Read the part with this symbol carefully and follow the
instructions in order to avoid risk.
WARNING
This indicates that the failure to follow the instructions can cause
serious injury or death.
CAUTION
This indicates that the failure to follow the instructions can cause the
minor injury or damage to the product.
The following symbols are displayed on indoor and outdoor units. (for R32)
ENGLISH
This symbol indicates that this appliance uses a flammable refrigerant.
If the refrigerant is leaked and exposure to an external ignition source,
there is a risk of fire.
This symbol indicates that the Operation Manual should be read
carefully.
This symbol indicates that a service personnel should be handling this
equipment with reference to the Installation Manual.
This symbol indicates that information is available such as the Operating
Manual or Installation Manual.
3
IMPORTANT SAFETY INSTRUCTIONS
WARNING
to persons when using this product, follow basic precautions, including the
following:
Children in the Household
This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction concerning use of the
appliance by a person responsible for their safety. Children should be supervised to
ensure that they do not play with the appliance.
For use in Europe:
This appliance can be used by children aged from 8 years and above and persons
with reduced physical, sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction concerning use of
the appliance in a safe way and understand the hazards involved. Children shall
not play with the appliance. Cleaning and user maintenance shall not be made by
children without supervision.
Installation
• Do not install the air conditioner on an unstable surface or in a place where
there is danger of it falling.
• Contact an authorized service center when installing or relocating the air
conditioner.
• Install the panel and the cover of the control box safely.
•
such as gasoline, propane, paint thinner, etc., are stored.
• Make sure that the pipe and the power cable connecting the indoor and outdoor
units are not pulled too tight when installing the air conditioner.
• Use standard circuit breaker and fuse that conform to the rating of the air
conditioner.
• refrigerant.
•
quids or gases
air; using
4
• The indoor/outdoor wiring connections must be secured tightly, and the cable
should be routed properly so that there is no force pulling the cable from the
connection terminals. Improper or loose connections can cause heat generation
• Install dedicated electric outlet and circuit breaker before using the air
conditioner.
• Do not connect the ground wire to a gas pipe, a lightning rod, or a telephone
ground wire.
• Keep any required ventilation openings clear of obstruction.
Operation
•
Be sure to use only those parts listed in the service parts list. Never attempt to
modify the equipment.
• Make sure that children do not climb on or hit the outdoor unit.
• Dispose of the batteries in a place where there is no danger of
•
• Cut off the power supply if there is any noise, smell, or smoke coming from the
air conditioner.
• thinner near
the air conditioner.
• Contact an authorized service center when the air conditioner is submerged by
ENGLISH
• Do not use the air conditioner for an extended period time in a small place
without proper ventilation.
• In the event of a gas leak (such as Freon, propane gas, L
P gas, etc.) ventilate
• To clean the interior, contact an authorized service center or dealer. Using harsh
detergents may cause corrosion or damage to the unit.
•
heating appliance
such as a heater are used simultaneously.
•
• Do not insert hands or other objects through the air inlet or outlet while the air
conditioner is operating.
• Make sure that the power cable is neither dirty, loose, nor broken.
• Never touch, operate, or repair the air conditioner with wet hands.
• Do not place any objects on the power cable.
• Do not place a heater or other heating appliances near the power cable.
Do not modify or extend the power cable. Scratches or peeling insulation on the
•
replaced.
5
•
Cut off the power supply immediately in the event of a blackout or a thunderstorm.
•
Take care to ensure that power cable could not be pulled out or damaged during
operation.
•
Do not touch refrigerant pipe, water pipe and any internal parts while the unit is
operating or immediately after operation.
Maintenance
• Do not clean the appliance by spraying water directly onto the product.
• Before cleaning or performing maintenance, disconnect the power supply and
wait until the fan stops.
Technical Safety
• Installation or repairs made by unauthorized persons can pose hazards to you
and others.
• Any person who is involved with working on or breaking into a refrigerant circuit
should hold a current valid certificate from an industry-accredited assessment
authority, which authorizes their competence to handle refrigerants safely in
accordance with an industry recognized assessment specification. (for R32)
•
Servicing shall only be performed as recommended by the equipment manufacturer.
Maintenance and repair requiring the assistance of other skilled personnel shall be
carried out under the supervision of the person competent in the use of flammable
refrigerants. (for R32).
• The information contained in the manual is intended for use by
service technician who is familiar with the safety procedures and equipped with
the proper tools and test instruments.
• Failure to read and follow all instructions in this manual can result in equipment
malfunction, property damage, personal injury and/or death.
• The appliance shall be installed in accordance with national wiring regulations.
• When the power cord is to be replaced, the replacement work shall be
performed by authorized personnel using only genuine replacement parts.
• This appliance must be properly grounded to minimize risk of electric shock.
• Do not cut or remove the grounding prong from the power plug.
• Attaching the adapter ground terminal to the wall receptacle cover screw does
not ground the appliance unless the cover screw is metal, uninsulated, and the
wall receptacle is grounded through house wiring.
6
• If you have any doubt whether the air conditioner is properly grounded, have the
• The refrigerant and insulation blowing gas used in the appliance require special
disposal procedures. Consult a service agent or a similarly qua
before disposing of them.
• If the supply cord is damaged, it must be replaced by the manufacturer or its
hazard.
• The appliance shall be stored in a well-ventilated area where the room size
corresponds to the room area as specified for operation. (for R32)
• The appliance shall be stored in a room without continuously operating open
flames (for example an operating gas appliance) and ignition sources
(for example an operating electric heater).
• The appliance shall be stored so as to prevent mechanical damage from
occurring.
CAUTION
To reduce the risk of minor injury to persons, malfunction, or damage to
the product or property when using this product, follow basic precautions,
including the following:
ENGLISH
Installation
Do not install the air conditioner in an area where it is directly exposed to sea
•
wind(salt spray).
• Install the drain hose properly for the smooth drainage of water condensation.
• Exercise caution when unpacking or installing the air conditioner.
• Do not touch the leaking refrigerant during installation or repair.
• Transport the air conditioner with two or more people or use a forklift.
• Install the outdoor unit such that it is protected from direct sunlight. Do not
place the indoor unit in a place where it is directly exposed to sunlight via the
windows.
Safely dispose of packing materials such as screws, nails or batteries using
•
proper packaging after installation or repair.
Install the air conditioner in a place where the noise from the outdoor unit or the
•
exhaust fumes will not inconvenience the neighbors. Failure to do so may result
7
Operation
• Remove the batteries if the remote control is not to be used for an extended
period of time.
•
conditioner.
• Be sure to check if there is a refrigerant leak after installing or repairing the air
conditioner.
• Do not place any object on the air conditioner.
• Never mix different types of batteries, or old and new batteries for the remote
control.
• Do not let the air conditioner run for a long time when humidity is very high or
when a door or a window has been left open.
• ttery. If your clothes
• Do not expose people, animals, or plants to the cold or hot wind from the air
conditioner for extended periods of time.
•
thoroughly and consult a doctor.
• Do not drink the water drained from the air conditioner.
• Do not use the product for special purposes, such as preserving foods, works
of art, and etc. It is an air conditioner for consumer purposes, not a precision
refrigeration system. There is risk of damage or loss of property.
• Do not recharge or disassemble the batteries.
Maintenance
• Never touch the metal parts of the air conditioner when removin
• Use a sturdy stool or ladder when cleaning, maintaining, or repairing the air
conditioner at a height.
• Never use strong cleaning agents or solvents when cleaning the air conditioner
or spray water. Use a smooth cloth.
8
OPERATION
Notes for Operation
Suggestion for Energy Saving
• Do not cool excessively indoors. This may be harmful for your health and may consume more electricity.
• Block sunlight with blinds or curtains while you are operating the air conditioner.
• Keep doors or windows closed tightly while you are operating the air conditioner.
•
• Speed up the fan to cool or warm indoor air quickly, within a short period of time.
• Open windows regularly for ventilation. The indoor air quality may deteriorate if the air conditioner is used for
long durations.
Clean the air filter once every 2 weeks. Dust and impurities collected in the air filter may block the air flow or
•
reduce the unit performance.
Parts and Functions
Indoor Unit Outdoor Unit
.
ENGLISH
1
Air Filter
2
Air Intake
3
Front Cover
4
On/Off Button
5
6
7
Air Outlet
NOTE
• The number and location of operation lamps may vary according to the model of the air conditioner.
• The feature may be changed according to the type of model.
1
Air Intake Vents
2
Air Outlet Vents
9
Wireless Remote Control
kW [3 s]
Inserting Batteries
If the display screen of the remote control begins
to fade, replace the batteries. Insert AAA (1.5 V)
batteries before using the remote control.
Remove the battery cover.
1
Insert the new batteries and make sure that the
2
+ and - terminals of the batteries are installed
correctly.
Installing the Remote Control Holder
To protect the remote control, install the holder where
there is no direct sunlight.
Operating method
Point the remote control towards the signal receiver
at the right side of the air conditioner to operate it.
NOTE
• The remote control may operate other electronic
devices if it is directed towards them. Make sure to
point the remote control towards the air conditioner
signal receiver.
• For proper operation, use a soft cloth to clean the
signal transmitter and receiver.
• In case of a function not provided in the product,
no buzzer sound occurs from the product when a
button for such function on the remote control is
pressed except for Air Flow Direction(
Display(
), Air Purication function( ).
), Energy
Choose a safe and easily accessible location.
1
Fix the holder by fastening 2 screws rmly with a
2
screwdriver.
10
Setting the Current Time
SWING
℃↔℉ [5 s]
ON/OFF
Insert batteries.
1
• The icon below blinks at the bottom of the
display screen.
2
Press or button to select the minutes.
Press SET/CANCEL button to nish.
3
NOTE
• The On/Off Timer is available after setting the
current time.
Operating the Air Conditioner
Without the Remote Control
You can use the ON/OFF button of the indoor unit to
operate the air conditioner when the remote control is
unavailable.
Open the front cover (Type1) or horizontal
1
vane(Type2).
Press the ON/OFF button.
2
Type1
ENGLISH
Using the °C/°F Conversion
Function(Optional)
This function changes unit between °C and °F.
• Press and hold
button about 5 seconds.
Type2
ON/OFF
NOTE
• The stepping motor may be broken, if the horizontal
vane opens rapidly.
• The fan speed is set to high.
• The feature may be changed according to the type
of model.
• The temperature cannot be altered when using this
emergency On/Off button.
• For cooling & heating models, the temperature is
set from 22 °C to 24 °C.
11
Using Wireless Remote Control
*
*
1
2
*
RESET
You can operate the air conditioner more conveniently with the remote control.
Button
Display
Screen
Description
Available Function
Single
Split
Multi
MODE
JET
MODE
FAN
SPEED
-
To turn on/off the air
conditioner.
To adjust the desired room
temperature in cooling,
heating or auto changeover
mode.
To select the cooling mode. ○ ○
To select the heating mode. ○ ○
To select the
dehumidication mode.
To select the fan mode. ○ ○
To select the auto
changeover/auto operation
mode.
To change room
temperature quickly.
To adjust the fan speed. ○ ○
To adjust the air ow
direction vertically or
horizontally.
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
NOTE
• * buttons may be changed according to the type of model.
• When connected to the Multi Outdoor unit, the Energy Display, Energy Control,
Silent and Smart Diagnosis function may not be supported.
12
*
*
1
2
*
RESET
Button
{ptly
Display
Screen
Description
To turn on/off air conditioner
automatically at desired
time.
Available Function
Single
Split
Multi
○ ○
ENGLISH
SET/
CANCEL
*LIGHT
OFF
ROOM
TEMP
°C↔°F[5 s]
*COMFORT
AIR
kW[3 s] -
*ENERGY
CTRL
DIAGNOSIS
[5 s]
-
- To cancel the timer settings. ○ ○
- To adjust time. ○ ○
-
-
To set/cancel the special
functions and timer.
To set the brightness of the
display on the indoor unit.
To display the room
temperature.
To change unit between °C
and °F.
To adjust the air ow to
deect wind.
To set whether or not
to display information
regarding energy.
To bring the effect of the
power saving.
To conveniently check
maintenance information of
a product.
○ ○
○ ○
○ ○
○ ○
○ ○
○ ×
○ ×
○ ×
13
Available Function
Button
2
Display
Screen
To purify the air by removing
particles that enters the
indoor unit.
Description
Single
Split
○
(Optional)
Multi
○
(Optional)
To reduce noise from
*
*
*
RESET -
1
NOTE
• Some functions may not be supported, depending on the model.
• * buttons may be changed according to the type of model.
• Press the SET/CANCEL button to operate the selected FUNC.
RESET
outdoor units.
To remove moisture
generated inside the indoor
unit.
To Initialize the remote
control settings.
○ ×
○ ○
○ ○
14
Memo
Loading...