User Manual
LX295
- 1 -
Part 15.21 statement
"Change or Modifications that are not expressly approved by the manufacturer could void the user's authority to operate the equipment. “
Part 15.105 statement
This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Part 15 Class B Compliance
This device and its accessories comply with part15 of FCC rules.
Operation is subject to the following two conditions:
(1)This device & its accessories may not cause harmful interference.
(2)This device & its accessories must accept any interference received, including interference that may cause undesired operation.
Body-worn Operation
This device has been tested for typical body-worn operations with the distance of 0.79inches (2.0cm) from the user’s body.
To comply with FCC RF exposure requirements, a minimum separation distance of 0.79inches(2.0cm) must be maintained from the user's body.
Additionally, Belt clips, holsters & other body-worn accessories may not contain metallic components.
If you received your LX295 in the mail, you may need to unlock it before making calls.
1.Press the END/PWR Switch for 2~3 seconds.
2.Press soft key Unlock.
3.Enter your four-digit lock code. For security purposes, the code will not be visible as you type.
Note: If you can’t recall your lock code, try using the last four digits of your Social Security number, the
last four digits of your Phone Number or 0000.
1.END/PWR Switch: Lets you power the phone on or off.
2.Antenna: Retractable antenna provides optimum reception for 800 MHz & 1900 MHz frequencies.
3.Power On Indicator: Illuminates red when the phone powers on or when you receive incoming calls. Flashes red when you have messages of scheduled alarms.
4.Headset Jack: Provides connection for an optional headset.
5.Volume Control Keys: Adjust the Ring Volume in the Main Menu or the Voice Volume during a call. The keys also scroll through mouths in the Calendar or pages in the MiniBrowser.
6.Mouse Key: Allows quick and easy scrolling through the menus.
7.OK: Lets you place a call, receive a call, end a call or select menu options.
8.CLR: Lets you clear an entry or back-up in the menu.
9.Folder : Lets you answer or end calls.
-10 -
To install the battery, insert the bottom of the battery into the opening on the back of the phone. Then, push the battery down until the latch clicks.
To remove the battery, press down on the latch and remove the battery from the phone.
To turn your phone on, move the On/Off Switch (near the antenna) to the ON position. Your phone performs a short self-test before letting you know it is operational.
If your phone does not turn on, make sure the battery is installed correctly and is adequately charged or has external power (via the AC Adapter, Cigarette Lighter Adapter or Hands-Free Car Kit).
To turn your phone off, move the On/Off Switch to the OFF position.
When your phone acquires Service, the Greeting (a banner of text), the current time and date and the Main Menu are displayed. If you are in authorized analog cellular provider’s service area, you are ready to send and receive calls.
When the phone is in an area without service for 15 minutes, it stops searching for service and enters into the power Save Mode. When your phone activates this feature, Power Save is displayed on your screen. The phone automatically checks for service periodically or you can check manually by pressing any key.
- 11 -
The Mouse Key lets you scroll circularly through menus quickly and easily.
As you navigate through a menu, the options are highlighted (Highlighted Test Example) . Select an option by highlighting it and pressing
. The scroll bar at the right of the menu keeps track of your position in the menu at all times.
For example, if you want to view your last incoming call: Incoming
1. From the Main Menu, select RECENT CALLS and press 2. (It may already be highlighted.)
2. Press the Mouse Key down to highlight and press |
. |
If you have received any calls, they are displayed on the screen.
To enter a letter, punctuation or number when creating Phone Book or Scheduler entries, press the corresponding key until the desired character appears. By default, the first letter of a word is capitalized and following letters are lowercase. Characters in the following order:
1 . ? , ‘ & - @ ( ) / ~
A B C 2 a b c 2 D E F 3 d e f 3 G H I 4 g h i 4 J K L 5 j k l 5
M N O 6 m n o 6
P Q R S 7 p q r s
T U V 8 t u v 8
W X Y Z 9 w x y z 9
Next 0
Shift
Space
- 12 -
After a character is entered, the cursor automatically advances to the next space after two seconds. You can also advance the cursor by pressing or entering a character not on the same key.
If you make a mistake, press to move the cursor left or [CLR] to erase a character. To clear the entire entry, press and hold [CLR] for two seconds.
- 13 -