Trim Frame
Bottom Duct (1)
1" Screws
Side Duct (1)
(4 Req’d, 2 Extra)
1
/2"
Screws
(11 Req’d, 2 Extra) Anti-Tip Bracket (1)
Bottom Bracket (1)
Upper Duct (1)
BUILT-IN TRIM KIT INSTALLATION INSTRUCTION
Depth
Height
3" Min.
Width
1/2" Screws (2)
1/2" Screws (2)
Front View of Microwave
Front
Rear
1/2" Screws (2)
(KEEP FOR FURTHER REFERENCE)
FOR LG TRIM-KIT MODELS: LX2060ST
FOR USE WITH LG MICROWAVE OVEN MODEL: LRM2060ST
CAUTION: For personal safety,remove
house fuse or open circuit breaker before
beginning installation to avoid severe or
fatal shock injury.
1
PARTS INCLUDED
2
Cutout Dimensions
Height
Width
Depth (min.)
30"
16
25
23
3
1
3
/4"
/2"
/4"
3
1. Disconnect the microwave oven before
proceeding with the installation.
2. Remove any loose items inside the microwave
oven.
3.
Fasten the bottom bracket to the bottom duct by
using two 1/2" screws.
1
4. Install bottom duct with four
/2" screws as
shown.
P/No. MFL33920501
1
4
Cutout Floor
1
2
" Screws (2)
Anti-Tip Bracket
a) b)
Upper Duct
Side Duct
3 Tabs
3 Holes
Existing Screw (1)
5
1. Fold or cut the front edge of the template,
along the front guide line. Place the template
flush along the front edge of the cutout floor,
aligning the center line of the template with the
center line of the cutout floor. Mark the center
positions with an awl or center punch for the
anti-tip bracket location as shown.
2. Remove the template and drill two holes for
the anti-tip bracket.
1. Remove the one existing screw from the left side
of the microwave oven.
2. Connect the side duct to the upper duct as
shown.
a) Insert projecting tabs of the upper duct into
the holes of the side duct.
b) Bend the tabs up as shown.
NOTE: Remove any oil or dirt on the surface of
the microwave oven before the ducts are attached.
3. Peel off the backing of the double sided tape.
Attach the side duct and upper duct assembly
on the microwave cabinet. Press down firmly
on the ducts. Fasten the duct assembly to the
left side of the cabinet with one existing screw.
3. Install the anti-tip bracket onto the cutout
floor using two 1/
2" screws.
2
6
Anti-Tip Assembly
Bottom Duct
1
2
" Screw
Bottom Bracket
Anti-Tip
Bracket
Cutout Opening
Positioning Flange
1
2
" Screw
Pilot Hole
Cutout Opening
Mounting Hole
Trim Frame
1" Screw
7
1. Slide the microwave oven part way into the
cabinet opening.
2. Bottom bracket must be flat to the cutout floor
to engage correctly with the anti-tip bracket as
shown.
3. Plug in the microwave oven.
4. Center the microwave oven within the cutout
opening and slide the microwave oven in place,
engaging the anti-tip bracket.
5. Ensure the microwave oven is accurately
centered .
1. Place the trim frame over the microwave oven.
2. Make sure the trim frame is level and the
microwave oven is centered within the trim
frame. Mark four center positions through the
four mounting holes of the trim frame.
NOTE: Center the trim frame equally on all four
sides.
3. Remove the trim frame and drill four pilot
holes.
6. Drill pilot holes through the positioning flange
and then install three 1/2
" screws at the front of
the bottom duct as shown.
4. Attach the trim frame by using four screws.
8
1. Your trim kit is now fully installed. Replace
any loose items that were removed from the
inside of the microwave oven.
2. Please keep these installation instructions for
future reference.
3
Loading...