LG LVC-C310HM, LVC-C302HP, LVC-C300NP, LVC-C300HM, LVC-C300NM User Manual
...
Operating Instructions
LVC-C300HM/HP/NM/NP LVC-C310HM/HP/NM/NP
LVC-C301HM/HP/NM/NP LVC-C311HM/HP/NM/NP
LVC-C302HM/HP/NM/NP LVC-C312HM/HP/NM/NP
LVC-C303HM/HP/NM/NP LVC-C313HM/HP/NM/NP
Before installing and using the camera,
please read these instructions throughly
and retain them for later reference.
2
CAUTION:TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER(OR BACK) NO USER SERVICE-
ABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SER-
VICE PERSONNEL.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
This symbol is intended to alert the
user to the presence of uninsulated
“dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of
electric shock to persons.
This symbol is intended to alert the
user to the presence of important
operating and maintenance (servicing) instructions in the literature
accompanying the appliance.
Warning
To prevent fire or shock hazard,do not expose the unit to rain or moisture.
To avoid electrical shock,do not open the cabinet. Refer servicing to qualified personnel only.
Wiring methods shall be in accordance with the National Electric Code,
ANSI/NFPA 70.
Regulatory Notices For U.S.A
This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to Part 15 of the FCC
Rules.These limits are designed to provide reasonable protection
against harmful interference when the equipment is opearted in a
commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will
be required to correct the interference at his own expense.
• A suitable conduit entries, knock-outs or glands shall be provided in the
cable entries of this product in the end user.
• Caution:Danger of explosion if battery is incorrectly replaced. Replaced
only with the same or equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer’s instructions.
• Holes in metal, through which insulated wires pass, shall have smooth
well rounded surfaces or shall be provided with brushings
.
Warning
This is a class A product. In a domestic environment this product
may cause radio interference in which case the user may be
required to take adequate measures.
This installation should be made by a qualified
service person and should conform to all local codes.
Contents
3
FEATURES
The power zoom color video camera is designed for use in monitoring system.
• High resolution and high sensitivity with a 1/4 inch CCD (Charge Coupled Device)
• High magnitude of zoom lens with optical X 27, Digital X 270(MAX)
• Auto Focus
• Auto White balance
• Auto exposure with DC Iris control
• Day & Night function : LVC-C310
• DSS(Digital Slow Shutter) is available : Optional
• WDR(Wide Dynamic Range) is available : Optional
Features............................................................................................................................................................................3
Cautions for Safe Operation
............................................................................................................................................4
Operating Controls and Their Functions.......................................................................................................................5
Power IN/CONTROL.........................................................................................................................................................6
External Key(A/D IN)........................................................................................................................................................7
MENU DESCRIPTIONS ....................................................................................................................................................8
CAMERA ID ..................................................................................................................................................................9
FOCUS MODE SET...............................................................................................................................................10-11
AWB SET ...............................................................................................................................................................12-13
AE SET ..................................................................................................................................................................14-16
SPECIAL SET ........................................................................................................................................................17-18
MOTION DET..............................................................................................................................................................19
F. OSD SET ................................................................................................................................................................20
E. SENSITIVITY ..........................................................................................................................................................21
WDR SET....................................................................................................................................................................22
On-Screen Display....................................................................................................................................................23-24
Specifications ...........................................................................................................................................................25-26
Cautions for Safe Operation
4
Power Supply
This camera must always be operated a 12V DC
UL Listed, Class 2 Power Supply only.
Handling of the unit
Be careful not to spill water or other liquids on the
unit, or to get combustible or metallic material
inside the body. If used with foreign matter inside,
the camera is liable to fail, or to be a cause of fire
or electric shock.
Operating and storage location
Avoid viewing a very bright object (such as light fittings) for an extended period. Avoid operating or
storing the unit in the following locations.
• Extremely hot or cold places (operating temperature 0°C-45°C)
• Damp or dust place
• Where it is exposed to rain
• Where it is subject to strong vibration
• Close to generators of powerful electromagnetic
radiation such as radio or TV transmitters.
Care of the unit
• Remove dust or dirt on the surface of the lens
with a blower.
• Use a dry soft cloth to clean the body. If it is very
dirty, use a cloth dampened with a small quantity
of neutral detergent, then wipe dry.
• Avoid the use of volatile solvents such as
thinners, alcohol, benzene, and insecticides.
They may damage the surface finish and/or
impair the operation of the camera.
Operating Controls and Their Functions
5
1. Tripod adaptor
This adaptor can also be attached on the bottom of the camera.
2. Lens mount cap
3. TELE Key
When push the TELE KEY, picture is telephoto
4. WIDE Key
When push the WIDE KEY, picture is wide angle
5. Focus Near Key
In a manual situation, focus get near.
6. Focus Far Key
In a manual situation, focus get far.
7. Menu Key
If you want to set up a diverse function, you can push this button.
8. Video output (S-Video type)
Connect to the S-Video in connector of a monitor.
9.
Interface of camera control JACK (6 Pin Din Jack Type)
• Connect to an external voltage controller
• You can supply a camera with power from this. (DC12V)
10. Video output(BNC type)
Connect to the video in connector of a monitor.
1
2
Power In / Control
6
You can adjust focus and zoom by a pin terminal on the back side
of the camera.
1
4
3
5
6
2
*
is the color of the cable.(If it is offered)
Adjust voltage from 1 pin and 2 pin
External Key (A/D IN)
7
Schematic diagram of wired
remote-control
1) C300'S
2) C310'S
6.8K 8.2K 12K 18K 33K 68K 180K
MENU DESCRIPTIONS
8
Using TELE, WIDE, FOCUS+, FOCUS- button
• TELE and WIDE are used for UP and DOWN.
• FOCUS+ and FOCUS- are used for INCREASE and DECREASE the data.
page 9
page 10
page 12
page 14
page 17
page 19
page 20
page 21
page 22
CAMERA ID
9
1. CAMERA ID
To connect a large number of camera , It can be
assigned to identification number to each camera for
camera control easily.
(OFF, 0 - 255 : total numbers of ID are 256)
• It only can be set this function using ID commend.
To transfer ID Code of camera , In first byte at PC control.
Set the ID number of camera , and then the ID number
display continuously.
Loading...