Operating Instructions
LVC-A730NP (PAL, Normal)
LVC-A730HP (PAL, High)
LVC-A730NM (NTSC, Normal)
LVC-A730HM (NTSC, High)
Before installing and using the camera,
please read these instructions throughly
and retain them for later reference.
2
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation! This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to
radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This Class B digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.
This symbol is intended to alert
the user to the presence of
uninsulated “dangerous voltage”
within the product’s enclosure
that may be of sufficient
magnitude to constitute a risk
of electric shock to persons.
This symbol is intended to
alert the user to the presence
of important operating and
maintenance (servicing)
instructions in the literature
accompanying the appliance.
CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE,
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Warning
Regulatory Notices
For U.S.A
To prevent fire or shock hazard, do not expose the unit to rain or moisture.
To avoid electrical shock, do not open the cabinet Refer servicing
to qualified personnel only.
Wiring methods shall be in accordance with the National Electric Code,
ANSI/NFPA 70.
This installation should be made by a
qualified service person and should
conform to all local codes.
3
Contents
FEATURES
Features...................................................................................................................................3
Cautions for Safe Operation
.....................................................................................................4
Operating Controls and Their Functions..................................................................................5
Power IN/CONTROL ...............................................................................................................6
Setting The Menu ...............................................................................................................7-13
On-Screen Display ...........................................................................................................14-15
Specifications ...................................................................................................................16-17
The power zoom color video camera is designed for use in monitoring system.
■
High resolution and high sensitivity with a 1/4 inch CCD (Charge Coupled Device)
■
High magnitude of zoom lens with optical X 16, Digital X128
■
Auto Focus
■
Auto White balance
■
Auto exposure with DC Iris control
■
On Screen display
4
Power Supply
This camera must always be operated a 12V
DC UL Listed, Class 2 Power Supply only.
Handling of the unit
Be careful not to spill water or other liquids on
the unit, or to get combustible or metallic
material inside the body. If used with foreign
matter inside, the camera is liable to fail, or to
be a cause of fire or electric shock.
Operating and storage location
Avoid viewing a very bright object (such as light
fittings) for an extended period. Avoid operating
or storing the unit in the following locations.
■
Extremely hot or cold places (operating
temperature -10
o
C~50oC, however, we
recommend that the unit be used within a
temperature range of 0
o
C~45oC)
■
Damp or dust place
■
Where it is exposed to rain
■
Where it is subject to strong vibration
■
Close to generators of powerful
electromagnetic radiation such as radio or
TV transmitters.
Care of the unit
■
Remove dust or dirt on the surface of the
lens with a blower.
■
Use a dry soft cloth to clean the body. If it
is very dirty, use a cloth dampened with a
small quantity of neutral detergent, then
wipe dry.
■
Avoid the use of volatile solvents such as
thinners, alcohol, benzene, and
insecticides. They may damage the surface
finish and/or impair the operation of the
camera.
Cautions for Safe Operation
5
Control names and Functions
1. Tripod adaptor
This adaptor can also be attached on the bottom of
the camera.
2. Lens mount cap
3.
When push the TELE KEY, picture is telephoto
4.
When push the WIDE KEY, picture is wide angle
5. Focus Near Key
In a manual situation, focus get near.
6. Focus Far Key
In a manual situation, focus get far.
7. Menu Key
If you want to set up a diverse function, you can push this
button.
8. Video output (S-Video type)
Connect to the S-Video in connector of a monitor.
9.
Interface of camera control JACK (6Pin Din Jack Type)
• Connect to an external voltage controller
• You can supply a camera with power from this. (DC12V)
10.Video output(BNC type)
Connect to the video in connector of a monitor.
Operating Controls and Their Functions
1 2
TELE WIDE
F.NEAR
CLASS 2
ONLY
F.FA R
CONTROL
VIDEO
MENU
S-VIDEO
OUT
POWER IN
34 8
910
LVC-A730
6
5
7
6
POWER IN/CONTROL
You can adjust focus and zoom by a pin terminal on the back
side of the camera.
*
is the color of the cable.(If it is offered)
PIN NO.
Description Color
*
1R X D Green
2T X D White
3 External Key input (A/D IN) Brown(Blue)
4 NC. Yelllow
5 GND Black
6 Power input (DC 12V) Red
1
4
3
562
3
A/D IN
POWER
ON/OFF
0.01
MENU
ON/OFF
DIGITAL
EFFECT
6.8K 8.2K 12K 18K 33K 68K 180K
WIDE
FAR
A/M or
Push Auto
NEAR
TELE
7
• The On Screen Display menu can be used by MENU,
TELE, WIDE, F.NEAR(F(+)), F.FAR(F(-)) Key.
Menu 1
1. INITIAL SET
Set the initial mode ON, the changed data are renewed.
2. BACKLIGHT
In case of the excessive light is behind the center object,
It is necessary to prevent the center object too darken.
Turn the BACKLIGHT ON, then the center object became
lighter.
3. COLOR
Use for changing color and monochrome of picture.
• ON: Color mode, • OFF: Black and White mode
Setting The Menu
MENU 1
INITIAL SET ON
BACKLIGHT OFF
COLOR ON
NEGATIVE OFF
FOCUS PUSH AUTO
FLICKERLESS OFF
WBC MODE AUTO
4. NEGATIVE
Use for changing NEGATIVE and POSITIVE mode.
• ON: NEGATIVE mode, • OFF: POSITIVE mode
5. FOCUS
AUTO/MAN: Set the focus mode to Auto or Manual.
PUSH AUTO: Set the focus mode to Push Auto mode.
6. FLICKERLESS
Set the FLICKER ON mode, then the flicker is removed.
• In case of NTSC system: Shutter Speed 1/100 sec
• In case of PAL system: Shutter Speed 1/120 sec
MENU 1
INITIAL SET ON
BACKLIGHT OFF
COLOR ON
NEGATIVE OFF
FOCUS PUSH AUTO
FLICKERLESS OFF
WBC MODE AUTO
8
9
7. WBC MODE
• AUTO: WB Range 2800°K ~ 8000°K
• SPECIAL(SWB): Under the special WB condition (Differ from curve of the control color
temperature), Adjust Red and Blue to perform a desired Auto White Balance.
• INDOOR( ): Use to set the preset
WBC INDOOR Mode (3200°K)
• OUTDOOR( ): Use to set the preset
WBC OUTDOOR Mode (5100°K)
WBC MODE SPECIAL
RED ADJUST 2
BLUE ADJUST 253
RED ADJUST 10
BLUE ADJUST 10
WBC MODE SPECIAL
RED ADJUST 0
BLUE ADJUST 0
Set the WB mode is
SPECIAL mode using F(+)
or F (-) key code. The
RED/BLUE ADJUST menu
is appeared.
Adjust the Red to a
desired value by using
F(+) or F (-) key code.
Adjust the Blue to a
desired value by using
F(+) or F (-) key code.
The whole MENU is
displayed using TELE or
WIDE key code. Moving
another item of MENU is
available.
WBC MODE INDOOR
WBC MODE OUTDOOR
Caution:The values of “RED ADJUST” and “BLUE ADJUST” are not changed when the “INITIAL SET” is set to “ON”
• MANUAL( ): Hue control adjustment is available manually. Adjust MWB CONTROL
to a desired value.
• PUSH AUTO(PWB): A regular environment or object
was forced to do White Balance action. And then the PWB mode turn off (Manual WB
mode). It makes good use of Manual WB mode in the usual environment.
It can prevent unsuitable color reproduction or decolor on the act of White Balance.
M
W
WBC MODE MANUAL
MWB CONTROL 0 MWB CONTROL 0
WBC MODE MANUAL
MWB CONTROL 0
Set the WB mode is MANUAL mode
using F(+) or F (-) key code. The
MWB CONTROL menu is appeared.
Adjust the MWB CONTROL
to a desired value.
The whole MENU is displayed using
TELE or WIDE key code. Moving
another item of MENU is available.
WBC MODE PUSH AUTO
PUSH OFF
Set the WB mode is MANUAL
mode using F(+) or F (-) key code.
The MWB CONTROL menu is
appeared.
PUSH ON
Adjust the PUSH AUTO
mode ON, WB act
automatically.
PUSH OFF
Adjust the PUSH AUTO
mode OFF, WB act
manually.
WBC MODE PUSH AUTO
PUSH OFF
The whole MENU is
displayed using TELE
or WIDE key code.
Moving another item of
MENU is available.
10
11
Menu 2
8. CAMERA ID
To connect a large number of camera, It can be assigned to
identification number to each camera control easily (OFF, 1~255 :
total numbers of ID are 256).
CAUTION: To transfer ID code of camera , set the ID number of
camera in first, And then the ID number display continuously.
9. SHARPNESS
Use to change the contour of scene (0~15).
10.BRIGHTNESS:
Use to change the brightness of scene (0~99).
11. ZOOM START (x1~x15)
Use to change the start magnification of zoom.(0~99).
12. ZOOM END (x2~)
Use to change the end magnification of zoom.
Caution : This value must be larger than the value of “ZOOM START”
13. FOCUS FROM (1Cm~ 10M)
Use to change the object distance limit for focusing.
For example, “1Cm” means that the camera is able to focus on
the objects which are from a distance of 1cm to infinite.
MENU 2
CAMERA ID OFF
SHARPNESS 10
BRIGHTNESS 42
ZOOM START x1
ZOOM END x128
FOCUS FROM 1Cm
AE MODE AUTO
AE MODE AGC
AGC ADJUST 0
AGC ADJUST 10
AE MODE AGC
AGC ADJUST 10
Set the AE mode to AGC using
F(+) or F (-) key code. The AGC
ADJUST menu is appeared.
Adjust the AGC ADJUST to a
desired value.
The whole MENU is displayed using
TELE or WIDE key code. Moving
another item of MENU is available.
14. AE MODE
In the situation is unadjustable exposure, AE mode support to make a fit exposure.
• AUTO: Use to compensate the exposure automatically.
• SHUTTER: Use to change the Shutter Speed control. In this time, AE mode act
automatically (8 steps control is available).
• IRIS: Use to change the value of Lens’s Iris (IRIS of lens is fixed manually, and the
action of exposure compensation depend on its of AGC).
• AGC: The change of AGC is available (00~255). (AGC of camera is fixed manually
and the action of exposure compensation depend on its of IRIS of LENS).
AE MODE IRIS
IRIS ADJUST 0 IRIS ADJUST 10
AE MODE IRIS
IRIS ADJUST 10
Set the AE mode to IRIS using
F(+) or F (-) key code. The IRIS
ADJUST menu is appeared.
Adjust the IRIS ADJUST to a
desired value.
The whole MENU is displayed using
TELE or WIDE key code. Moving
another item of MENU is available.
12
13
• MANUAL: Use to set the shutter speed, IRIS and AGC manually.
AE MODE MANUAL
SHUTTER NORMAL
IRIS ADJUST 0
AGC ADJUST 60
SHUTTER NORMAL
AE MODE MANUAL
SHUTTER NORMAL
IRIS ADJUST 0
AGC ADJUST 60
IRIS ADJUST 10
Set the AE mode is MANUAL
mode using F(+) or F (-) key
code. The SHUTTER, IRIS
ADJUST, AGC ADJUST MENU
is appeared.
Adjust the SHUTTER
to a desired value.
The whole MENU is
displayed using TELE
or WIDE key code.
Moving another item of
MENU is available.
Adjust the IRIS ADJUST to
a desired value.
AE MODE MANUAL
SHUTTER NORMAL
IRIS ADJUST 10
AGC ADJUST 80 AGC ADJUST 80
AE MODE MANUAL
SHUTTER NORMAL
IRIS ADJUST 10
AGC ADJUST 60
The whole MENU is displayed
using TELE or WIDE key code.
Moving another item of MENU
is available.
Adjust the AGC
ADJUST
to a desired value.
The whole MENU is
displayed using TELE or
WIDE key code. Moving
another item of MENU
is available.
On-Screen Display
Some of these functions will
be displayed every time the
camera is operated and then
disappeared after 5 seconds.
FUNCTION OSD Format Description
1 Focus Mode Non display Focus Auto Mode
☞
Focus Manual mode
2 Back Light Non display Back Light OFF
Back Light ON
3 Shutter Speed Non display Normal Shutter (NTSC:1/60
PAL: 1/50)
1/125 8 variable steps.
1/10,000
4 STAND-BY Indicate the camera stand-by during the
camera’s power turning on.
5 CAMERA ID According to write the identification number to
each camera, multi-point control is available
(PC Control 000~255)
14
☞ 1/10000
STAND-BY
WT x12 125
12 346
75
15
On-Screen Display
FUNCTION OSD Format Description
6 WBC Mode
Non display White Balance AUTO
SWB Special Auto White Balance; Adjustment Mode according to
change of external illuminant. RED ADJUST and BLUE
ADJUST (0~255) are available. After changing R/B value, the
maintenance mode is “AUTO”.
WB Preset for INDOOR (3200°K)
Wb Preset for OUTDOOR (5100°K)
Manual WB Adjustment; In manual mode the HUE control is
available (0 ~ 99)
PWB Push Auto White Balance; Turn this mode ON, the white trace
automatically. Turn this mode OFF, preserve the white of final
auto tracing action (Manual)
7
ZOOM Display
WT x16 In case of 16X Zoom
WT x32 In case of 32X Zoom (Digital Zoom 2X)
WT x64 In case of 64X Zoom (Digital Zoom 4X)
M
W
Specifications
Image device 1/4" interline transfer CCD
NTSC, High resolution : 380,000
NTSC, Normal resolution : 250,000
PAL, High resolution : 440,000
PAL, Normal resolution : 290,000
Sync system Internal sync
Horizontal resolution Approx.450 Line (NTSC, High resolution)
320 Line (NTSC, Normal resolution)
450 Line (PAL, High resolution)
320 Line (PAL, Normal resolution)
(at center of screen)
Lens x16 Optical Zoom(f=3.9~63mm, F1.6 - 2.4 Auto IRIS)
Digital Zoom Normal resolution : x32 Zoom(Digital Zoom x2)
High resolution : x128 Zoom(Digital Zoom x8)
Minimum illumination 1 Lux (F1.6)
S/N More than 48dB (AGC OFF)
Automatic control Auto Exposure(DC iris, AGC)
Auto white balance
Auto focus (Zoom tracking)
16
17
Specifications
Power requirement 12V DC UL Listed, Class 2 Power Supply only
Video output BNC-type, S-Video-type (1.0Vp-p, 75ohms)
Power consumption Max 4.7W
operating temperature -10
o
C
~ 50oC
Operating Humidity 0%~80%
Storage temperature -20oC
to+60oC
Dimensions 59.4mm(W)
x 61.2mm(H) x 95mm(D)
Specifications are subject to change without notice.
P/NO: 3834RS0076T
ݷᔫᒎฉ
LVC-A730NP(PAL,普通分辨率)
LVC-A730HP(PAL,高分辨率)
LVC-A730NM(PAL,普通分辨率)
LVC-A730HM(NTSC,高分辨率)
在您使用此摄像机之前，请完整阅读此操
作指南以供参考。
2
本产品经测试符合 FCC 第 15 部分有关 B 类数字设备的限制条件。这些限
制条件是为提供合理的保护措施，防止在住宅区安装设备时产生有害干扰
而制定的！本设备会产生、使用和辐射无线电频率能量。如未正确安装和
使用，可能对无线电通讯造成有害干扰。
然而，并不保证在特殊的安装方式下不产生干扰。如果本设备确实对无线
电或电视接收设备造成严重干扰，这可以通过关闭和打开本设备来确定。
另外，我们请用户通过以下方法来克服干扰 ;
• 重新定向或重新定位接收天线。
• 增大本设备和接收设备之间的距离。
• 将本设备插入另一个插座，使本设备和接收设备位于不同的电路中。
•
咨询经销商或有经验的无线电/电视技术人员以获取帮助。
本 B 类数字设备符合加拿大关于产生干扰的设备之规定中的全部要求
此符号用于警示用户，产品外
壳存在未绝缘的危险电压，会
产生对人身造成电击的危险。
此符号用于提醒用户，随设备
一起提供的印刷品中包含重要
的操作和维护（维修）指南。
警告：为了减少电击的危险，请勿拆下前盖
（或后盖）
内部没有任何用户可以维修的零部件。
如需维修，请联系专业维修人员。
ᓖፀ
电击危险请勿打开
வস
ࢾဉී᎖ග
ᆐ೫ᒏ࢟ૣူ৺ ༿ݙገকޘອ۩ഴᏴᎦᒦޭဘࡼણஹᒦ
ᆐ೫ܜ࢟ૣࡼᆉሙ ༿ݙገࡌఎ૦ఫ ྙኊᆒኀ ༿ೊᇹᓜጓᆒኀ
ཽᏋ
接线方法应该符合美国国家电气规程 ANSI/NFPA 70 之规定
此安装应该由专业服务人员进行，并应遵
守当地相应规定。
3
ഺ
ᄂ࢛
特性..........................................................................................................................................3
安全操作注意事项 ...................................................................................................................4
操作控制及其功能 ....................................................................................................................5
电源输入/控制 ..........................................................................................................................6
设置菜单 .............................................................................................................................7-13
屏幕菜单显示 (OSD).........................................................................................................14-15
规格 ..................................................................................................................................16-17
此电动变焦彩色摄像机是为监视系统专门设计的。
• 高分辨率
高灵敏度的 1/4 英寸 CCD 电荷耦合装置
• 高倍数变焦镜头 光学变焦 X 16 数码变焦 X 128
• 自动对焦
• 自动白平衡
• DC 光圈控制自动曝光
• 屏幕菜单显示
4
࢟Ꮞ
此摄像机必须使用 12V DC UL 认证 2 类电源
ۃᏥስ૦
请注意不要将水或其它液体溅到摄像机内部
也
不要让可燃性物品或金属物品掉入摄像机内
如
果摄像机内部有杂质 则可能会导致摄像机故障
或引发火灾或电击
ဧࡀ࢛
不要长时间观看过于明亮的物体
如灯具 避
免在以下环境中使用或存放此设备
■
过热或过冷的地方 工作温度为 -10oC~50oC,
但是我们建议此设备使用的温度范围为
0
o
C~45oC)
■
潮湿或有灰尘的地方
■
有雨的地方
■
有强烈振动的地方
■
靠近有强电磁辐射的地方 如收音机或电视
发射机附近
ስ૦ۣዸ
■
使用吹风机将表面的灰尘或脏物吹掉
■
请使用软布清洁机身 如果太脏 请使用带
有少量中性清洁剂的软布清洁
然后擦干
■
请不要使用挥发性溶剂 如稀释剂 酒精
苯和杀虫剂 们会损坏表面或机身
ڔཝݷᔫᓖፀူሲ
5
控制名称及功能
1. 三脚架转接器
此转接器还可以安装到摄像机的底部
2. 镜头安装盖
3.
当按 TELE KEY 时 图像为远距拍摄
4.
当按 WIDE KEY 时 图像为广角拍摄
5. 拉近焦距键
在手动操作时
将焦距拉近
6. 拉远焦距
在手动操作时
将焦距拉远
7. 菜单键
如果您要设置不同的功能
可按此键
8. 视频输出 S-Video 型
连接到监视器的 S-Video 输入接口
9.
摄像机控制 JACK 接口 6 针 DIN JACK 型
• 连接到外部电压控制器
• 您可以通过此接口为摄像机供电
(DC12V)
10.视频输出
BNC 型
连接到监视器的视频输入接口
ݷᔫ఼ᒜૺถ
1 2
TELE WIDE
F.NEAR
CLASS 2
ONLY
F.FA R
CONTROL
VIDEO
MENU
S-VIDEO
OUT
POWER IN
34 8
910
LVC-A730
6
5
7
6
࢟Ꮞၒྜྷ0఼ᒜ
1
4
3
562
您可以通过摄像机背面的针形端子调节焦距和变焦。
*
为电缆颜色。（如果提供）
3
A/D IN
POWER
ON/OFF
0.01µ
MENU
ON/OFF
DIGITAL
EFFECT
6.8K 8.2K 12K 18K 33K 68K 180K
WIDE
FAR
A/M or
Push Auto
NEAR
TELE
୭ ႁී ዕྻ
*
1
R X D 绿色
2
T X D 白色
3
外部键输入 (A/D IN) 褐色 蓝色
4 NC.
黄色
5
接地 黑色
6
电源输入 (DC 12V) 红色
7
• 您可以通过 MENU TELE WIDE F.NEAR(F(+))
F.FAR(F(-)) 键来使用屏幕显示菜单
MENU 1 ݩ 1
1. INITIAL SET ߱ဪᒙ
将初始模式设为 ON 则更新修改的数据
2. BACKLIGHT ۳
当中心物体后面的光线过强时 您需要避免中心物体过暗
将 BACKLIGHT 设为 ON 这样中心物体会变亮
3. COLOR ዕྻ
用来将图像改变为彩色和单色
• ON 开 彩色模式,• OFF 关 黑白模式
ᒙݩ
MENU 1
INITIAL SET ON
BACKLIGHT OFF
COLOR ON
NEGATIVE OFF
FOCUS PUSH AUTO
FLICKERLESS OFF
WBC MODE AUTO
8
4. NEGATIVE ঌስ
用于改变 NEGATIVE 负像 和 POSITIVE 正像 模
式
• ON 开 NEGATIVE 模式,• OFF:POSITIVE 模式
5. FOCUS ࣪ୡ
AUTO/MAN 自动/手动 将对焦模式设为自动或手动
PUSH AUTO 强制自动 将对焦模式设为强制自动模
式
6. FLICKERLESS ᇄ࿑ႄ
将 FLICKER 设为 ON 模式将消除闪烁
• 对于 NTSC 制式 快门速度 1/100 秒
• 对于 PAL 制式
快门速度 1/120 秒
MENU 1
INITIAL SET ON
BACKLIGHT OFF
COLOR ON
NEGATIVE OFF
FOCUS PUSH AUTO
FLICKERLESS OFF
WBC MODE AUTO
9
7. WBC MODE ڹຳ఼ᒜෝါ
• AUTO ᔈࣅ 白平衡范围 2800°K ~ 8000°K
• SPECIAL(SWB)
ᄂၐڹຳ 在特殊的白平衡条件 不同于控制色温曲线 下 调整
红色和蓝色以达到所需的自动白平衡
• INDOOR( ): 用于设置预设
白平衡控制室内模式 (3200°K)
• OUTDOOR( ): 用于设置预设
白平衡控制室外模式 (5100°K)
WBC MODE SPECIAL
RED ADJUST 2
BLUE ADJUST 253
RED ADJUST 10
BLUE ADJUST 10
WBC MODE SPECIAL
RED ADJUST 0
BLUE ADJUST 0
使用 F(+) 或 F (-) 键将 WB
模式设为 SPECIAL
出现
RED/BLUE ADJUST 菜
单
使用 F(+) 或 F (-) 键将
红色调整到所需的值
使用 F(+) 或 F (-) 键将
蓝色调整到所需的值
使用 TELE 或 WIDE 键
显示整个 MENU
此时
可移动 MENU 的另一项
目
WBC MODE INDOOR
WBC MODE OUTDOOR
注意 当 INITIAL SET 被设为 ON 时 无法调整 RED ADJUST 和 BLUE ADJUST 的值
10
• MANUAL( )(၄ࣅ):可以进行手动色调控制 将 MWB CONTROL 手动白平衡控制
调整到所需的值
• PUSH AUTO(PWB)(强制自动):正常环境或目标强制执行白平衡 然后 PWB 模式关闭
手动 WB 模式 在通常环境下使用手动 WB 白平衡 模式较为理想
它可以避免白平衡出现不稳定的色彩重现或脱色
M
W
WBC MODE MANUAL
MWB CONTROL 0 MWB CONTROL 0
WBC MODE MANUAL
MWB CONTROL 0
使用 F(+) 或 F (-) 键将 WB 模式设为
MANUAL 出现 MWB CONTROL
菜单
将 MWB CONTROL 手动
白平衡控制
调整到所需的
值
使用 TELE 或 WIDE 键显示整个
MENU
此时可移动 MENU 的另一
项目
WBC MODE PUSH AUTO
PUSH OFF
使用 F(+) 或 F (-) 键将 WB 模
式设为 MANUAL
出现 MWB
CONTROL 菜单
PUSH ON
将 PUSH AUTO 模式设
为 ON
WB 会自动执
行
PUSH OFF
将 PUSH AUTO 模式设
为 OFF
WB 需手动执
行
WBC MODE PUSH AUTO
PUSH OFF
使用 TELE 或 WIDE 键
显示整个 MENU
此时
可移动 MENU 的另一项
目
11
MENU 2 ݩ 2
8. CAMERA ID ስ૦ ID
当连接多台摄像机时 可以为每台摄像机指定一个识别码 这样就
可以更容易的对每台摄像机进行控制 OFF 1~255 摄像机总 ID
为 256
ᓖፀ:要设置摄像机ID先设定第一台摄像机的ID随后会连续显
示
ID
编号
9. SHARPNESS ༹ᇠࣞ
用来改变场景的轮廓 (0~15)
10.BRIGHTNESS ೡࣞ :
用来改变场景的亮度 (0~99)
11. ZOOM START (x1~x15) ܤୡఎဪ
用来改变变焦放大的开始位置 (0~99)
12. ZOOM END (x2~) ܤୡஉၦ
用来改变变焦放大的结束位置
注意 此值必须大于 ZOOM START 的值
13. FOCUS FROM (1Cm~ 10M)(࣪ୡ࢛)
用开改变对焦的物距限定值
例如 1Cm 指物体对焦范围为 1 厘米到无穷远
MENU 2
CAMERA ID OFF
SHARPNESS 10
BRIGHTNESS 42
ZOOM START x1
ZOOM END x128
FOCUS FROM 1Cm
AE MODE AUTO
AE MODE AGC
AGC ADJUST 0 AGC ADJUST 10
AE MODE AGC
AGC ADJUST 10
使用 F(+) 或 F (-) 键将 AE 模式
设为 AGC
出现 AGC
ADJUST 菜单
将 AGC ADJUST 自动增益
控制调整 调整到所需的值
使用 TELE 或 WIDE 键显示整个
MENU
此时可移动 MENU 的另一
项目
12
14. AE MODE ᔈࣅ໎ෝါ
当出现不可调整曝光的情形时 AE 自动曝光 模式支持进行合适的曝光
• AUTO ᔈࣅ 用于对曝光进行自动补偿
•SHUTTER ඡ 用于改变快门速度控制 此时 AE 模式自动执行 可使用 8 级
控制
• IRIS མ 用于改变镜头光圈值 镜头光圈被手动固定 曝光补偿的操作取决于
其 AGC
• AGC ᔈࣅᐐፄ఼ᒜ 改变 AGC 的值 (00~255) 摄像机的 AGC 被手动固定 曝
光补偿取决于其镜头光圈
AE MODE IRIS
IRIS ADJUST 0 IRIS ADJUST 10
AE MODE IRIS
IRIS ADJUST 10
使用 F(+) 或 F (-) 键将 AE 模
式设为 IRIS 出现 IRIS
ADJUST 菜单
将 IRIS ADJUST 光圈调整
调整到所需的值
使用 TELE 或 WIDE 键显示整个
MENU 此时可移动 MENU 的另一
项目
13
• MANUAL ၄ࣅ 用于手动设置快门速度 IRIS 和 AGC
AE MODE MANUAL
SHUTTER NORMAL
IRIS ADJUST 0
AGC ADJUST 60
SHUTTER NORMAL
AE MODE MANUAL
SHUTTER NORMAL
IRIS ADJUST 0
AGC ADJUST 60
IRIS ADJUST 10
使用 F(+) 或 F (-) 键将 AE 模
式设为 MANUAL 出现
SHUTTER IRIS ADJUST
AGC ADJUST 菜单
将 SHUTTER 快门
调整到所需的值
使用 TELE 或 WIDE 键
显示整个 MENU 此时
可移动 MENU 的另一项
目
将 IRIS ADJUST 光圈调
整 调整到所需的值
AE MODE MANUAL
SHUTTER NORMAL
IRIS ADJUST 10
AGC ADJUST 80 AGC ADJUST 80
AE MODE MANUAL
SHUTTER NORMAL
IRIS ADJUST 10
AGC ADJUST 60
使用 TELE 或 WIDE 键显示整
个 MENU
此时可移动
MENU 的另一项目
将 AGC ADJUST 自
动增益控制调整 调
整到所需的值
使用 TELE 或 WIDE 键
显示整个 MENU
此时
可移动 MENU 的另一项
目
14
ືݩመာ (OSD)
以下某些功能在操作摄像机时
会在屏幕上显示 5 秒钟后消失
ถ OSD ৃါ ႁී
1
对焦模式 无显示 自动对焦模式
☞
手动对焦模式
2
背光 无显示 背光关闭
背光开
3
快门速度 无显示 普通快门 ( NTSC: 1/60
PAL: 1/50)
1/125 8
步
1/10,000
4
待机 在电源打开过程中摄像机处于待机状态
5
摄像机 ID 对每台摄像机设定识别码 可进行多点控
制 PC 控制 000~255
☞ 1/10000
STAND-BY
WT x12 125
12 346
75
15
ືݩመာ (OSD)
ถ OSD ৃါ ႁී
6
白平衡控 无显示 自动白平衡
制模式 SWB S特殊自动白平衡
根据外部光线变化的调整模式 可使用 RED
ADJUST 和 BLUE ADJUST (0~255) 修改 R/B 值后 维护模式为
AUTO
室内白平衡预设 (3200°K)
室外白平衡预设 (5100°K)
手动白平衡调整 在手动模式下可使用 HUE 控制 (0 ~ 99).
PWB 强制自动白平衡
此模式打开时 白平衡自动调整 此模式关闭时
保留最后自动追踪的白平衡 手动
7 变焦显示 WT x16 16X 变焦情况下
WT x32 32X 变焦 2X 数码变焦 情况下
WT x64 64X 变焦
4X 数码变焦 情况下
M
W
16
ৃ
成像设备
1/4" 隔行CCD
NTSC 高分辨率 380,000
NTSC
普通分辨率 250,000
PAL
高分辨率 440,000
PAL
普通分辨率 290,000
同步系统 内部同步
水平分辨率 大约 450 线
NTSC 高分辨率
320 线 NTSC 普通分辨率
450 线 PAL 高分辨率
320 线 PAL 普通分辨率
屏幕中央
镜头 x16 光学变焦 (f=3.9~63mm, F1.6 - 2.4 自动光圈)
数码变焦 普通分辨率 x32 变焦 x2 数码变焦
高分辨率 x128 变焦 x8 数码变焦
最小照明 1 Lux (F1.6)
信噪比 大于 48dB AGC 关
自动控制 自动曝光 DC 光圈 AGC
自动白平衡
自动对焦
变焦跟踪
17
ৃ
电源要求 仅 12V DC UL 认证 2 类电源
视频输出 BNC 型 S-Video 型 1.0Vp-p 75 欧姆
功耗 最大 4.7w
工作温度
-10oC
~ 50oC
工作湿度
0%~80%
储存温度
-20oC
+60oC
尺寸
59.4mm(宽)
x 61.2mm(高)x 95mm(厚)
规格若有更改恕不另行通知
P/NO.: 3834RS0076T
Loading...