Page 1
OWNER’S MANUAL
EZ SLIM WALL MOUNT
Please read this manual carefully before installation
and retain it for future reference.
LSW600B
P/NO : MFL63640525 (1207-REV00)
www.lg.com
Page 2
Accessories
Wall mount anchor
8 units
Safety clip
2 units
Wall mount screw
8 units
User manual
Guide spacer 4 units
Set protection
cushion 4 units
Guide space screw 4 units
(M8X25 mm)
IMPORTANT SAFETY INSTRUCTIONS
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Warning
This wall mount should be installed by a trained and
experienced installer designated by the retailer.
Having the product installed by a non-specialized installer is
very dangerous and can cause damage or injury.
Use a trained and experienced installer to move or
replace the wall mount, if needed.
Installation requires special techniques and moving or installing
the product on your own can cause serious safety issues.
When installing the wall mount, never hang the
power or signal cable on the rear side the TV.
The cord can be damaged and cause a fire, an electric
shock or damage to the product.
2
Do not install the product where the weight cannot be
supported.
If the strength of the location where the wall mount is installed
is not strong enough, it can fall off and cause an injury.
After installing the wall mount, do not hang on
the product and prevent severe impact to the
product.
The product can fall off and cause injury.
Page 3
Caution
Install the product according to the directions in the user
manual.
If the product is not installed based on the directions in the user
manual, it can cause a serious injury or damage to the product.
ENGLISH
When installing the product or adjusting the height of
the product after installing, always do so with 2
people.
Working alone can cause the product to fall off and result in
injury or damage to the product.
During the installation, check the type of wall material
and use the sealed anchor and screw if the conditions
comply.
If you do not use the designated anchor or screw, the mount
may not be able to withstand the weight of the product and
cause a safety issue.
Do not wipe the product with a wet towel and do not use
any heater or humidifier below where the product is
installed.
If water flows into the product or if moisture and heat are applied
to the product, it can cause a fire, an electric shock or problem to
the product.
Unplug the power cord from the power outlet before
installing the product.
If you install the product with the power cord plugged, it can
cause an electric shock or a fire.
Do not allow the video connectors connected to the
display to press against the wall. Use the included rightangle adapters if needed.
Only use attachments/accessories specified by the manufacturer.
When drilling holes in the wall, always use a drill bit
and drill of designated diameter. Also follow the
designated directions for the depth of the hole.
If the product is installed without following the designated
method, the product may be unstable and cause a safety
issue.
Donot install the product near any object that may
cause vibration.
Do not install the product near any high voltage power cable
or power source.
Do not install the product with bare hands. Always
wear proper work gloves.
It can cause an injury.
Before installation
* Do not use the product for purposes other than mounting a display on the wall.
* When installing/using the wall mount, be cautious of product damage and avoid accidents.
* If you have not fully read and understood the installation manual, do not install the product and contact
the dealer to have a specialized installer install the product for you.
* Even if you are not a specialized installer, it is advantageous to have experience in mechanical or
construction field in completely understanding this manual and installing the product.
* This product is designed to be mounted to walls that use standard intervals between the studs.
* Install the screw to attach the wall mount so that it can be assembled at the center from both ends of
the studs. Use of stud finder, a separate device, is recommended.
* Install the product only on a vertical wall. The manufacturer is not responsible for issue from installing
the product on severely wall or on the ceiling.
* Keep the included accessories out of reach of babies or children as it can cause safety issues including
suffocation from swallowing the parts.
* Make sure screws are tight against the wall, but do not overtighten.
* Be careful not to install a TV that exceeds the weight restrictions of the wall mount.
* Be careful with the tools used during installation to prevent accidents or damage.
3
Page 4
Installation method
- Tools you will need : Phillips head "+" driver(Manual or motorized) Ø4 mm drill bit for wood or steel / Level / Stud
finder / Drill. You may also need an 8 mm socket wrench or an Ø8 mm drill bit for concrete.
Fixating the mounting bracket on the TV
1
- If the screw will not fully tighten when using a guide spacer, recheck the assembly depth of the screw and
refer to the technical service manual.
Guide spacer
<Work procedure>
1. Check to see if the display has screws installed into the mounting holes. If so, remove those.
2. Assemble the guide spacer and the guide spacer screw in order as shown in the picture.
Lay the set down and secure the guide spacer and the set using the screws.
- Put the product on the table placing the screen face down. When doing this, it is highly recommended to place
a floor cushion or soft clothes on the flat table before putting the product on it to avoid any damage of the
screen surface.
- Tighten the screw until the set, guide spacer and the screw are fully pressing against one another.
- Use the "+" driver (Manual or motorized) when tightening the screw.
Guide spacer screw
4
Page 5
How to attach to masonry walls
2
- Use the anchors for wall material of concrete, light concrete, strong natural stone, soft natural stone masonry
brick and hallow block that do not crack.
Please follow the below direction.
- Check the material of the wall and the thickness of the finishing.
- When installing the product on wall material not designated, install the product so that each fixated location
can withstand the pull out load of 70 kgf (686 N) and shear load of 100 kgf (980 N) or above.
Anchor
ENGLISH
a
d
- Use the Ø8 mm drill bit for concrete and hammer (Impact) drill.
a. Use a drill bit Ø8 mm to drill a hole for the anchor location within a depth of 80 mm ~ 100 mm
b. Clean the drilled hole.
c. Insert the sealed anchor to the hole. (When inserting the anchor, use a hammer.)
d. Set the wall mount on the wall by aligning to the location of the hole. and, set the angle adjusting part to face upward.
e. Align the wall mount bolt to the hole and tighten it. Then, fasten the bolts at torque of 45 - 60 kgf/cm.
How to install the wall mount
3
b
Wall mount screw
e
c
→ If the screw cannot be assembled in the designated location inevitably, it can be assembled by rearranging to the
closest location. But, do not change 2 or more locations from the designated spot.
→ Fix the right and left side with two bolts each.
→ Wall mounting equipment will be set up based in VESA 600X400 regulation.
→ At this time, use a "+" driver (Manual or motorized) or 8 mm wrench to tighten the screw so that the wall, wall
bracket and screw are completely pressed against one another.
5
Page 6
How to assemble the wall mount support and display
4
- Always install the display with 2 or more people.
Safety clip
1. Set the display with the guide spacer assembled on the wall mount bracket on the wall in arrow direction.
At this time, align the bottom assembly part and lift the set up lightly to align the top part.
2. When adjusting the horizontal level, use the safety ring provided by pressing it slightly to in the direction as
illustrated. There is a risk of the product falling when the safety ring is not used as shown in the illustration.
→ Pull the bottom of the TV/Monitor to affirm that it is firmly fixed.
→ See A above,be sure to lift a product/speakers assembly by the product only, do not lift using only the speakers.)
→ When installing a display rotated, only rotate the display 90 degrees (portrait mode). (Only applies for VESA
200x200, 400x400)
How to level the Display
5
After installing the display, check to make sure it is level.
The wall mount has two screws that make minor adjustments to the level.
± 10 mm
(horizontal adjustment)
6
Page 7
Tilt Angle Adjustment
6
- The tilt angle can be adjusted after installation and setup.
- When you adjust the angle, hold the product carefully with both hands to avoid any damage to the product
or wall.
➊
➋
➍
➌
➌
<Top Tilt> <Bottom Tilt>
➊
12° ± 2°
➋
10° ± 2°
<Left Tilt>
ENGLISH
<Right Tilt>
➍
10° ± 2°
12° ± 2°
< Set Side >
* The above numbers are the maximum allowed, some models may do less.
→ Use both hands when adjusting the angles. Do not place the hands on the TV’s back side or the wall mount
while adjusting. If could cause injury.
→ Two adult people who are capable of adjusting the tilt angle to need excessive force.
→ When adjusting the number ➊ angle of the product, you must use both hands and then you can adjust the angle
as shown above.
→ When adjusting the number ➋ angle of the product, you must use both hands and then you can adjust the angle
as shown above.
→ When adjusting the number ➌ angle of the product, you must use both hands and then you can adjust the angle
as shown above.
→ When adjusting the number ➍ angle of the product, you must use both hands and then you can adjust the angle
as shown above.
< Set Top >
7
Page 8
7
How to adjust height
+ 80 mm + 80 mm
Clamping bolt
- 80 mm- 80 mm
<When moving the set downward> <When moving the set upward>
→
It is possible to move the set upward and downward by as much as 80 mm.
→
Please use both hands when adjusting the set upward and downward. Do not forget to remove the bolts on both sides of
the set before adjusting the height. Anchor the bolts again after height adjustment.
→
Use 14~55 kgf of power when adjusting the set upward or downward.
* Three adults are needed when installing the product and adjusting the height.
Otherwise, serious injury or product damage can occur.
8
Page 9
How to adhere the protection cushions and arrange cables
8
→ Use the protection cushions to reduce shock between the wall and TV/Monitor.
→ Arrange the cable like shown. You can purchase the cable holder separately or use it provided like accessory of
the TV/Monitor get.
Dimension
[ unit : mm ]
ENGLISH
25
25 25 25 25
600
45
81
210
25 25 25 25 25
530
658
465
238
400
81
20
Model LSW600B
Width (mm) 658
Height (mm) 465
Depth (mm) 25
Weight (kg) 6.3
Weight with packing (kg) 7.7
Wall mount Vesa specification 600 X 400
Max Load Capacity (kg) 75
Max. 214
Min. 25
9
Page 10
The model and serial number of the product is
located on the back or one side of the product.
Record it below should you ever need service.
MODEL
SERIAL
Supported Displays:
(Please contract the retailers or refer to the TV owner’s
manual for applicable models.)
Loading...