LG LSW600B User Manual

OWNER’S MANUAL
EZ SLIM WALL MOUNT
Please read this manual carefully before installation and retain it for future reference.
LSW600B
P/NO : MFL63640507 (1112-REV03)
www.lg.com
* 1 Year Warranty (Europe : 2 Year) If material or workmanship proves defective under normal use, during the warranty period, please
contact the retailer where you purchased it. This warranty is good only to the original purchaser of the product and effective only in the local area.
Wall mount anchor
8 units
Safety clip
2 units
Wall mount screw
10 units
User manual
Guide spacer 4 units
IMPORTANT SAFETY INSTRUCTIONS
Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions.
Warning
This wall mount should be installed by a trained and experienced installer designated by the retailer.
Having the product installed by a non-specialized installer is very dangerous and can cause damage or injury.
Use a trained and experienced installer to move or replace the wall mount, if needed.
Installation requires special techniques and moving or installing the product on your own can cause serious safety issues.
When installing the wall mount, never hang the power or signal cable on the rear side the TV.
The cord can be damaged and cause a fire, an electric shock or damage to the product.
Guide space screw 4 units
(M8X25mm)
Set protection
cushion 4 units
Do not install the product where the weight cannot be supported.
If the strength of the location where the wall mount is installed is not strong enough, it can fall off and cause an injury.
After installing the wall mount, do not hang on the product and prevent severe impact to the product.
The product can fall off and cause injury.
2
Caution
Install the product according to the directions in the user manual.
If the product is not installed based on the directions in the user manual, it can cause a serious injury or damage to the product.
When installing the product or adjusting the height of the product after installing, always do so with 2 people.
Working alone can cause the product to fall off and result in injury or damage to the product.
ENGLISH
During the installation, check the type of wall material and use the sealed anchor and screw if the conditions comply.
If you do not use the designated anchor or screw, the mount may not be able to withstand the weight of the product and cause a safety issue.
Do not wipe the product with a wet towel and do not use any heater or humidifier below where the product is installed.
If water flows into the product or if moisture and heat are applied to the product, it can cause a fire, an electric shock or problem to
the product.
Unplug the power cord from the power outlet before installing the product.
If you install the product with the power cord plugged, it can cause an electric shock or a fire.
Do not allow the video connectors connected to the display to press against the wall. Use the included right­angle adapters if needed.
Only use attachments/accessories specified by the manufacturer.
When drilling holes in the wall, always use a drill bit and drill of designated diameter. Also follow the designated directions for the depth of the hole.
If the product is installed without following the designated method, the product may be unstable and cause a safety issue.
Donot install the product near any object that may cause vibration.
Do not install the product near any high voltage power cable or power source.
Do not install the product with bare hands. Always wear proper work gloves.
It can cause an injury.
Before installation
* Do not use the product for purposes other than mounting a display on the wall. * When installing/using the wall mount, be cautious of product damage and avoid accidents. * If you have not fully read and understood the installation manual, do not install the product and contact
the dealer to have a specialized installer install the product for you.
* Even if you are not a specialized installer, it is advantageous to have experience in mechanical or
construction field in completely understanding this manual and installing the product. * This product is designed to be mounted to walls that use standard intervals between the studs. * Install the screw to attach the wall mount so that it can be assembled at the center from both ends of
the studs. Use of stud finder, a separate device, is recommended. * Install the product only on a vertical wall. The manufacturer is not responsible for issue from installing
the product on severely wall or on the ceiling. * Keep the included accessories out of reach of babies or children as it can cause safety issues including
suffocation from swallowing the parts. * Make sure screws are tight against the wall, but do not overtighten. * Be careful not to install a TV that exceeds the weight restrictions of the wall mount. * Be careful with the tools used during installation to prevent accidents or damage.
3
Installation method
- Tools you will need : Phillips head "+" driver(Manual or motorized) Ø4mm drill bit for wood or steel / Level / Stud
finder / Drill. You may also need an 8mm socket wrench or an 8mm drill bit for concrete.
Fixating the mounting bracket on the TV
1
- If the screw will not fully tighten when using a guide spacer, recheck the assembly depth of the screw and refer to the technical service manual.
Guide spacer
<Work procedure>
1. Check to see if the display has screws installed into the mounting holes. If so, remove those.
2. Assemble the guide spacer and the guide spacer screw in order as shown in the picture. Lay the set down and secure the guide spacer and the set using the screws.
- Put the product on the table placing the screen face down. When doing this, it is highly recommended to place a floor cushion or soft clothes on the flat table before putting the product on it to avoid any damage of the screen surface.
- Tighten the screw until the set, guide spacer and the screw are fully pressing against one another.
- Use the "+" driver (Manual or motorized) when tightening the screw.
Guide spacer screw
4
Loading...
+ 8 hidden pages