Page 1
OWNER’S MANUAL
Wall Mounting Bracket
Please read this manual carefully before operating
your set and retain it for future reference.
LSW200B
LSW200BG
LSW200BX
LSW200BXG
LSW400B
LSW400BG
P/NO : MFL63640502 (1005-REV01)
www.lg.com
Page 2
* 1 Year Warranty
If material or workmanship proves defective under normal use, during the warranty period, please contact the
retailer where you purchased it. This warranty is good only to the original purchaser of the product and effective
only in the local area.
Component
Wall mount anchor
LSW200B/LSW200BG 4 units
LSW200BX/LSW200BXG 4 units
LSW400B/LSW400BG 6 units
Wall mount screw
10 units
Guide spacer
4 units
* LSW200B/LSW200BG
LSW400B/LSW400BG
* LSW200BX/LSW200BXG
Guide space
screw 4units
* LSW200B/LSW200BG/
LSW400B/LSW400BG
: M6X18m
* LSW200BX/LSW200BXG
: M6X28mm
Safety clip 2 units
Due to the shallow clearance between the display and the wall, the LSW200BG/LSW200BXG and LSW400BG Wall Mounts
may require the use of the included angled adapters.
Safety clip screw
2 units
(M4X12mm)
<Component cable with angled connectors>
PVC Washer
4 units
Set protection cushion
<HDMI angle adapter>
4 units
* Note that the included angle adapters may
block other connections on the back of the TV.
* Make sure the connectors on the cables
connected to the display do not press against
the wall.
User manual
IMPORTANT SAFETY INSTRUCTIONS
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Warning
This wall mount should be installed by a trained and
experienced installer designated by the retailer.
Having the product installed by a non-specialized installer is
very dangerous and can cause damage or injury.
Do not install the product where the weight cannot be
supported.
If the strength of the location where the wall mount is installed
is not strong enough, it can fall off and cause an injury.
Use a trained and experienced installer to move or
replace the wall mount, if needed.
Installation requires special techniques and moving or installing
the product on your own can cause serious safety issues.
When installing the wall mount, never hang the
power or signal cable on the rear side the TV.
The cord can be damaged and cause a fire, an electric
shock or damage to the product.
2
After installing the wall mount, do not hang on the
product or apply severe impact to the product.
The product can fall off and cause injury.
Page 3
Caution
Install the product according to the directions in the
user manual.
If the product is not installed based on the directions in
the user manual, it can cause a serious injury or damage
to the product.
During the installation, check the type of wall
material and use the sealed anchor and screw if the
conditions comply.
If you do not use the designated anchor or screw, the
mount may not be able to withstand the weight of
the product and cause a safety issue.
Do not wipe the product with a wet towel and do not use any
heater or humidifier below where the product is installed.
If water flows into the product or if moisture and heat are applied to the
product, it can cause a fire, an electric shock or problem to the product.
Unplug the power cord from the power outlet before
installing the product.
If you install the product with the power cord plugged, it can
cause an electric shock or a fire.
Do not allow the video connectors connected to the
display to press against the wall. Use the included
right-angle adapters if needed.
Only use attachments/accessories specified by the
manufacturer.
ENGLISH
When installing the product or adjusting the height of
the product after installing, always do so with 2 people.
Working alone can cause the product to fall off and result in
injury or damage to the product.
When drilling holes in the wall, always use a drill bit
and drill of designated diameter. Also follow the
designated directions for the depth of the hole.
If the product is installed without following the designated
method, the product may be unstable and cause a safety
issue.
Do not install the product near any object that may
cause vibration.
Do not install the product near any high voltage power
cable or power source.
Do not install the product with bare hands. Always
wear proper work gloves.
It can cause an injury.
Before installation
* Do not use the product for purposes other than mounting a display on the wall.
* When installing/using the wall mount, be cautious of product damage and avoid accidents.
* If you have not fully read and understood the installation manual, do not install the product and contact
the dealer to have a specialized installer install the product for you.
* Even if you are not a specialized installer, it is advantageous to have experience in mechanical or
construction field in completely understanding this manual and installing the product.
* This product is designed to be mounted to walls that use standard intervals between the studs.
* Install the screw to attach the wall mount so that it can be assembled at the center from both ends of
the studs.
Use of stud finder, a separate device, is recommended.
* Install the product only on a vertical wall.
The manufacturer is not responsible for issue from installing the product on severely wall or on the
ceiling.
* Keep the included accessories out of reach of babies or children as it can cause safety issues including
suffocation from swallowing the parts.
* Make sure screws are tight against the wall, but do not overtighten.
* Be careful not to install a TV that exceeds the weight restrictions of the wall mount.
* Be careful with the tools used during installation to prevent accidents or damage.
3
Page 4
Installation method
- Tools you will need : Phillips head "+" driver(Manual or motorized) Ø4mm drill bit for wood or steel / Level / Stud finder / Drill. You
may also need an 8mm socket wrench or an 8mm drill bit for concrete.
- Installation method is described based on the LSW200B model. The actual product may differ from the picture.
Fixating the mounting bracket on the TV
1
If the screw will not fully tighten when using a guide spacer, recheck the assembly depth of the screw and
refer to the technical service manual.
<Work procedure>
Guide spacer
Guide spacer
screw
Install the PVC washer on models
37/42/47LE53*, 37/42/47LE55*,
42/47/55LX65*, 42/47/55LX68*
Install the wall mount only after
attaching the PVC washer
on the back cover of the TV.
1. Check to see if the display has screws installed into the
mounting holes. If so, remove those.
2. Assemble the guide spacer and the guide spacer screw in
order as shown in the picture.
- Assemble the guide spacer to the set by tightening the
screw.
- Tighten the screw until the set, guide spacer and the screw
are fully pressing against one another.
- Use the "+" driver (Manual or motorized) when tightening
the screw.
How to attach to masonry walls
2
- Use the anchors for wall material of concrete, light concrete, strong natural stone, soft natural stone masonry brick and
hallow block that do not crack.
Please follow the below direction.
- Check the material of the wall and the thickness of the finishing.
- When installing the product on the wooden wall, refer to page 5.
- When installing the product on wall material not designated, install the product so that each fixated location can withstand
the pull out load of 70kgf (686N) and shear load of 10kgf (980N) or above.
Wall mount screwAnchor
a
- Use the Ø8mm drill bit for concrete and hammer (Impact) drill.
a. Use a drill bit Ø8mm to drill a hole for the anchor location within a depth of 80mm ~ 100mm
b. Clean the drilled hole.
c. Insert the sealed anchor to the hole. (When inserting the anchor, use a hammer.)
d. Set the wall mount on the wall by aligning to the location of the hole. and, set the angle adjusting part to face upward.
e. Align the wall mount bolt to the hole and tighten it. At this time, the bolt must be tightened with torque of 45kgf/cm or above.
b
c
d
e
How to install the wall mount
3
<When installing on a masonry wall>
→ When you separate the 8 screws on the wall mount connected to the wall bracket for use with a wooden wall,
it is much easier to install the product.
→ When installing the product on a masonry wall, turn
A
Separate the wall mount screw.
4
the 8 screws on the A part counterclockwise to
separate the screw and bracket.
→ After aligning the wall bracket to the location to
install, mark the part to screw on the wall and then
remove the wall bracket.
→ Refer to page 4 to attach the wall bracket.
→ Use a level to check whether the wall mount is level.
Page 5
LSW400B/LSW400BG Model
Wall mount screw
<When mounting to wooden studs>
→ If the screw cannot be assembled in the designated location
inevitably, it can be assembled by rearranging to the closest
location. But, do not change 2 or more locations from the
designated spot.
→ LSW200B/LSW200BG/LSW200BX/LSW200BXG
: Assemble the wall mount screw on 1 left and 1 right location
on the top part and 1 left and 1 right location on the bottom
part.
→ LSW400B/LSW400BG : Assemble the wall mount screw on
2 left and 2 right locations on the top and 1 left and 1 right
location on the bottom part.
→ At this time, use a "+" driver (Manual or motorized) or 8mm
wrench to tighten the screw so that the wall, wall bracket and
screw are completely pressed against one another.
ENGLISH
76mm
406mm
wood stud
drywall
b. After aligning the wall bracket on the wall where the center of the wood stud is
a. Locate and mark the centers of
the wall studs using a stud finder.
How to assemble the wall mount support and display
4
- Always install the display with 2 or more people.
Safety clip
* Assemble the wall mount
support, product and safety clip.
marked, mark the location of the screws and then remove the wall bracket.
c. Use a level to make sure your screw marks are level.
d. Use the 4mm drill bit for wood to drill holes with the depth of 76mm or above
where the wall mount screw location is marked on the wall.
e. Clean the drilled hole.
f. Tighten the wall mount screws for the wall bracket on the drilled hole.
→ At this time, tighten the screw so that the wall, wall bracket and the wall mount
screw are pressed against one another. (Drywall can be damaged when tightened
with excessive force, please be careful.)
→ When tightening the screw use the "+" driver (Manual or motorized) or 8mm
wrench.
Safety clip screw
1. Set the display with the guide spacer assembled on the wall
mount bracket on the wall in arrow direction. At this time, align
the bottom assembly part and lift the set up lightly to align the
top part.
2. When adjusting the location, assemble the provide safety
clip as shown in the picture to prevent the product from
moving. Tighten the safety clip screw completely. If the
safety clip is not tightened as shown in the picture, the
product can fall off.
→ Pull on the bottom of the set to make sure the display is
secure.
→ When installing a display rotated, only rotate the display 90
degrees (portrait mode).
(Only applies for VESA 200X200, 400x400)
→ The clearance from the wall is 14mm for this product. Make
sure to keep a certain level of distance from the wall so
that excessive force is not applied on the cable or accessory.
→ When you push the product with excessive force, the product
can be damaged.
drywall
5
Page 6
How to level the Display
° ~ °± °
145
5
After installing the display, check to make sure it is level. The wall mount has two
screws that make minor adjustments to the level.
LSW200B/LSW200BG/LSW200BX/LSW200BXG : ± 5mm(Leveling)
LSW400B/LSW400BG : ± 10mm(Leveling)
Cable arrangement and set protection cushion
6
- Arrange the cables as shown in the picture. Use some type of cable banding device to hold all the cables together.
- Attach the set protection cushion to mitigate the impact between the wall and the set when adjusting the angle.
Attach the set protection cushion as shown in the picture.
<LSW200B/LSW200BG/LSW200BX/LSW200BXG>
Wall Mount VESA
Max.UL Load Capacity
Product specification
<With the bracket removed.>
Model Name
Width (mm)
Height (mm)
Depth (mm)
Weight (kg)
Specification
(kg)
LSW200B
LSW200BG
281 281 440
234 234 450
14 21.5 14
1.5 1.5 3.4
200 X 200 200 X 200 400 x 400
40 40 50
LSW200BX
LSW200BXG
LSW400B
LSW400BG
Model Name
Width (mm)
Height (mm)
Depth (mm)
Weight (kg)
Wall Mount VESA
Specification
Max.UL Load Capacity
(kg)
<LSW400B/LSW400BG>
<With the bracket attached.>
LSW200B
LSW200BG
460 460 460
234 234 450
20 27.5 20
3.2 3.2 5.6
200 X 200 200 X 200 400 x 400
40 40 50
LSW200BX
LSW200BXG
LSW400B
LSW400BG
° ~ °± °
° ~ °± °
6
Page 7
< LSW200B/LSW200BG/LSW200BX/LSW200BXG>
[ Unit : mm ]
<With the bracket removed.>
<With the bracket attached.>
< LSW400B/LSW400BG>
ڌڐڌ
Max.
145
Max.
ENGLISH
Min.
YW
Min.
<With the bracket removed.>
<With the bracket attached.>
Max.
Max.
Min.
Min.
7
Page 8
The model and serial number of the product is located
on the back or one side of the product. Record it below
should you ever need service.
MODEL
SERIAL
Supported Displays:
(Consult the retailer for detail list of models.)
LSW200B/LSW200BG Supports:
- 37/42/46/47LD*, 37/42/47LE*, 42/47/55LX*
(LSW200BX/LSW200BXG :47LE95*/47LX95*/47LX98*)
LSW400B/LSW400BG Supports:
- 52/55/60LD*, 52/55/60LE*
Loading...