LG LSCG307ST Installation Manual [fr]

INSTALLATION MANUAL

GAS COOKTOP

LSCG366ST

LSCG306ST

LSCG367ST

LSCG307ST

Please read this guide thoroughly before installation.

www.lg.com

MFL62725506_01

ENGLISH

FRANÇAIS

INSTALLATION INSTRUCTIONS

INSTALLATION SAFETY INSTRUCTIONS

BEFORE YOU BEGIN

Read these instructions completely

and carefully.

Installation of this cooktop must conform with

local codes, or in the absence of local codes,

with the National Fuel Gas Code, ANSI Z223.1/

NFPA.54, latest edition. In Canada, installation

must conform with the current Natural Gas

Installation Code, CAN/CGAB149.1 or the current

Propane Installation Code, CAN/CGA-B149.2, and

with local codes where applicable. This cooktop

has been design-certified by CSA International

according to ANSI Z21.1, latest edition and

Canadian Gas Association according to

CAN/CGA-1.1 latest edition.

As with any appliance using gas and generating

heat, there are certain safety precautions you

should follow. You will find these precautions in the

lmportant Safety Information section in your User’s

Guide. Read them carefully.

• IMPORTANT – Save these instructions for

local electrical inspector’s use.

• IMPORTANT – Observe all governing

codes and ordinances.

Note to Installer: Leave these instructions with

the appliance after installation is completed.

Note to Consumer: Keep the User’s Guide and

Installation Instructions for future reference.

NOTE: This appliance must be properly

grounded.

• The electrical diagram is in an envelope attached

to the back of the cooktop.

• Skill level – Installation of this appliance requires

basic mechanical skills.

• Proper installation is the responsibility of

the installer.

• Product failure due to improper installation is not

covered under the Warranty.

• Remove all tape and packaging.

• Make sure the burners are properly seated and

level.

• Take the accessory pack off of the cooktop

• Check to be sure that no cooktop parts have

come loose during shipping.

ENGLISH

IN THE COMMONWEALTH OF MASSACHUSETTS

PREPARING FOR INSTALLATION

FOR YOUR SAFETY

• This product must be installed by a licensed

plumber or gas fitter.

• When using ball type gas shut-off valves, they shall

be the T-handle type.

• A flexible gas connector, when used, must not

exceed 3 feet in length.

INSTALLATION INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE INSTALLATION

WARNING:

If the information in

this manual is not followed exactly, a fire or

explosion may result causing property damage,

personal injury or death.

– Do not store or use combustible materials,

gasoline or other flammable vapors and

liquids in the vicinity of this or any other

appliance.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switches,

• Do not use any phone in your building.

• Immediately call your gas supplier from a

neighbor′s phone. Follow the gas supplier

instructions.

• If you cannot contact your gas supplier, call

the fire department.

Installation and service must be performed by

a qualified installer, service agency or the gas

supplier.

TOOLS YOU WILL NEED

MATERIALS YOU MAY NEED

• Gas line shut-off valve

• To reduce the possibility of gas leaks, apply teflon

tape or a thread compound approved for use with

LP or Natural gases to all threaded connections.

• Flexible metal appliance connector (5/8” I.D.)

A 3-foot length is recommended for ease of

installation but other lengths are acceptable.

Never use an old connector when installing a new

cooktop.

• Flare union adapter for connection to gas supply

line (3/4” or 1/2” NPT x 5/8” I.D.)

• Flare union adapter for connection to pressure

regulator on cooktop. (1/4” NPT x 1/2” I.D.)

• Liquid leak detector or soapy water.

Phillips screwdriver

Joint

Sealant

Pipe Fittings

Flexible Connector

Shut Off

Valve

Open-end or

adjustable wrench

Pipe wrench(2)

(one for support)

Flat-blade screwdriver

Pencil and ruler

IMPORTANT: Remove all packing material and

literature before connecting gas and electrical supply.

• Have your cooktop installed by a qualified installer.

• Your cooktop must be electrically grounded in

accordance with local codes or, in the absence

of local codes, in accordance with the National

Electrical Code (ANSI/NFPA 70, latest edition).

In Canada, electrical grounding must be in

accordance with the current CSA C22.1 Canadian

Electrical Code Part 1 and/or local codes.

Refer to 3. Electrical Connections, in this manual.

• Be sure the wall coverings around the cooktop can

withstand heat generated by the cooktop up to

200 °F.

• Avoid placing cabinets above the cooktop.

To minimize the hazard caused by reaching over

the open flames of operating burners, install a

ventilation hood over the cooktop that projects

forward at least 5” beyond the front of the cabinets.

INSTALLATION SAFETY INSTRUCTIONS

INSTALLATION INSTRUCTIONS

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill

or hurt you and others. All safety messages will follow the safety alert symbol and either

the word “ WARNING” or “CAUTION”.

BEFORE YOU BEGIN

Remove all tape and packing materials before using the cooktop. Dispose all plastic bags after

unpacking the cooktop. Never allow children to play with packing materials.

IMPORTANT SAFETY INSTRUCTIONS

Read these instructions completely and carefully. Improper installation, adjustment, alteration,

service or maintenance can cause injury or property damage.

For assistance or additional information, consult a qualified installer, service agency, manufacturer

(dealer) or your gas supplier.

Never reuse old flexible connectors. The use of old flexible connectors can cause gas leaks and

personal injury. Always use NEW flexible connectors when installing a gas appliance.

This symbol will alert you to hazards or unsafe practices which could

cause serious bodily harm or death.

WARNING

This symbol will alert you to hazards or unsafe practices which could

cause bodily injury or property damage.

CAUTION

ENGLISH

INSTALLATION INSTRUCTIONS

• The ventilating hood must be constructed of

sheet metal not less than 0.0122” thick. Install

above the cooktop with a clearance of not less

than 1/4” between the hood and the underside of

the combustible material or metal cabinet. The

hood must be at least as wide as the appliance

and centered over the appliance. Clearance

between the cooking surface and the ventilation

hood surface MUST NEVER BE LESS THAN 24

INCHES.

EXCEPTION: Installation of a listed microwave

oven or cooking appliance over the cooktop shall

conform to the installation instructions packed with

that appliance.

• If cabinets are located above the cooktop, allow

a minimum clearance of 30” between the cooking

surface and the bottom of unprotected cabinets.

• If a 30” clearance between cooking surface and

overhead combustible material or metal cabinets

cannot be maintained, protect the underside of

the cabinets above the cooktop with not less than

1/4” insulating millboard covered with sheet metal

not less than 0.0122” thick. Clearance between

the cooking surface and protected cabinets MUST

NEVER BE LESS THAN 24 INCHES.

• The vertical distance from the plane of the cooking

surface to the bottom of adjacent overhead

cabinets extending closer than 1” to the plane of

the cooktop sides must not be less than 18”. (See

the Dimensions and Clearances illustration in this

manual.)

• Do not abstruct the combustion or ventilation air.

• Leak testing of the appliance shall be conducted

according to the manufacturer’s instructions.

CAUTION: Items of interest to

children should not be placed in cabinets above

the cooktop.

- children climbing on the cooktop to reach items

could be seriously injured.

WARNING: This appliance must

not be installed with a ventilation system that

blows air downward toward the cooktop. This

type of ventilation system may cause ignition

and combustion problems with the gas cooking

appliance resulting in personal injury or unintended

operation.

INSTALLATION SAFETY INSTRUCTIONS

(continued)

Provide enough clearances between the cooktop and

adjacent combustible surfaces. These dimensions

must be met for safe use of your cooktop.

The location of the electrical outlet and pipe opening

may be adjusted to meet specific requirements.

The cooktop may be placed with 2 3/4” clearance to

the back wall.

DIMENSIONS AND CLEARANCES

INSTALLATION INSTRUCTIONS

1. MAINTAIN THE FOLLOWING

MINIMUM CLEARANCE

DIMENSIONS

3. RECOMMENDED GAS SUPPLY

LOCATION FROM BACKWALL

4. MAKE SURE WALL COVERINGS,

COUNTERTOP AND CABINETS

AROUND COOKTOP CAN

WITHSTAND HEAT(UP TO 200℉)

GENERATED BY COOKTOP

2. COOKTOP AND CUTOUT

DIMENSIONS

13˝MAX. Depth of unprotected

overhead cabinets

A˝ MIN. clearance from

cutout to side wall on

the right of the unit

18˝ MIN. height

from countertop

to nearest cabinet

on either side of

unit

30˝ MIN. clearance

from countertop to

unprotected overhead

surface

A˝ MIN. clearance

from cutout to side

wall on the left of

unit.

L″ MIN.

Between

cutout

and the wall

behind the

cooktop

K″ MIN.

From front

edge of cutout

and front edge

of countertop

Recommended

gas supply

location

1” Min. From Backwall

From Cutout

Center Line

To ensure accuracy, it is best to make

a template when cutting the opening

in the counter

width

width cut

depth

B″MIN

depth cut

depth

height

width

MODEL A B C D E F G H J K L

30″ Cooktop 11

″ 30″ 30″ 21

″ 3

″ 28

″ 19

″ 28

″ 19

″ 1

″ 2

″

36″ Cooktop 11

″ 36″ 36″ 21

″ 3

″ 33

″ 19

″ 33

″ 19

″ 1

″ 2

″

Wall covering ,

cabinets and

counterto p

must withstan d

heat up to

200°F

ENGLISH

INSTALLING THE COOKTOP UNIT

INSTALLATION INSTRUCTIONS

1. LOCATE ELECTRICAL OUTLET

AND GAS SHUT-OFF VALVE

BENEATH CABINET

2. INSERT COOKTOP INTO CUTOUT

Install a manual shut-off valve in the gas line

in an easily accessible location outside the

cooktop. Be sure you know how and where to

shut off the gas supply to the cooktop. Install

the electrical outlet 12˝ below the countertop.

3. LOCATE RETAINER BRACKETS

Remove the retainer brackets from the

literature package.

NEVER RE-USE

OLD FLEX

CONNECTORS.

Install a manual shut-off valve in the gas line

in an easily accessible location outside the

cooktop. Be sure you know how and where to

shut off the gas supply to the cooktop. Install

the electrical outlet 12˝ below the countertop.

Shut-Off

valve

Retainer brackets

Cooktop

Screw

Countertop

Retainer brackets

NOTE: The retainer brackets MUST be

installed to meet local codes or, in their

absence, with the National Electrical Code

ANSI/NFPA No. 70, latest edition.

4. INSTALL THE RETAINER BRACKETS

Install the retainer brackets to the bottom

of the cooktop unit. then snug the bolts

against the bottom of the countertop as

shown

Electrical

outlet 12˝

below

countertop

This cooktop is designed to operate at a pressure of

5” of water column on natural gas or 10” of water

column on LP, propane or butane gas.

Make sure you are supplying your cooktop with the

type of gas for which it is designed.

This cooktop is convertible for use on natural or

propane gas. When using this cooktop on LP gas,

conversion must be made by a qualified LP installer

before attempting to operate the cooktop on that gas.

For correct operation, the pressure of natural gas

supplied to the regulator should be between 5” and

13” of water column.

For LP gas, the pressure supplied must be between

10” and 13” of water column.

When checking for correct operation of the regulator,

the inlet pressure must be at least 1” more than the

operating -manifold- pressure as given above.

The pressure regulator located at the inlet of the

cooktop manifold must remain in the supply line

regardless of whether natural or LP gas is being

used.

A flexible metal appliance connector used to connect

the cooktop to the gas supply line must have an I.D.

of 5/8” and can be 3 feet max. in length for easy

installation. In Canada, flexible connectors should be

single wall metal connectors less than 6 feet in

length.

1. PROVIDE ADEQUATE GAS SUPPLY

INSTALLATION INSTRUCTIONS

Shut off the main gas supply valve before removing

the old cooktop and leave it off until the new hook-up

has been completed. Don’t forget to relight the pilot on

other gas appliances when you turn the gas back on.

Because hard piping restricts movement of the

cooktop, the use of a CSA International-certified

flexible metal appliance connector is recommended

unless local codes require a hard-piped connection.

Never reuse an old connector when installing a

new cooktop. If the hard piping method is used, you

must carefully align the pipe; the cooktop cannot be

moved after the connection is made.

To prevent gas leaks, put pipe joint compound on, all

male -external- pipe threads.

Install a manual gas line shut-off valve in the gas

line in an easily accessed location outside of the

cooktop. Be sure everyone operating the cooktop

knows where and how to shut off the gas supply

to the cooktop.

Install male 1/2” flare union adapter to the 1/2”

NPT internal thread at inlet of pressure regulator.

Use a backup wrench on the pressure regulator

fitting to prevent damage.

Install male 1/2” or 3/4” flare union adapter to the

NPT internal thread of the manual shut-off valve,

taking care to back-up the shut-off valve to keep

it from turning.

Connect a flexible metal connector to the adapter

on the cooktop. Position the cooktop to permit

connection at the shut-off valve.

When all connections have been made, be sure

all cooktop controls are in the off position and

turn on the main gas supply valve.

Check for gas leaks by using manometer.

If a manometer is not available, turn the gas

supply on to the cooktop on and use a liquid leak

detector at all joints and connections to check for

leaks.

Tighten all connections, if necessary, to prevent

gas leakage in the cooktop or supply line.

WARNING!:

DO NOT USE A FLAME TO CHECK FOR GAS LEAKS.

Disconnect the cooktop and its individual shut-off

valve from the gas supply piping system during any

pressure testing of that system at test pressures

more than 1/2 psig(3.5kPa).

Isolate the cooktop from the gas supply piping

system by closing its individual shut-off valve during

any pressure testing of the gas supply system at test

pressures equal to or less than 1/2 psig(3.5kPa)

2. CONNECT THE COOKTOP TO GAS

ENGLISH

INSTALLATION INSTRUCTIONS

FLEXIBLE CONNECTOR HOOKUP

Pressure

regulator

Installer: Inform the

consumer of the

location of the gas

shut-off valve.

1/2” or 3/4”

Gas pipe

Flex

connector

(6 ft. max.)

Gas Flow into Range

Adapter

Gas

shut-off valve

Adapter

ELECTRICAL REQUIREMENTS

120 Volt, 60 Hertz, properly grounded dedicated

circuit protected by a 15 A or 20 A circuit breaker or

time delay fuse.

GROUNDING

IMPORTANT: FOR PERSONAL SAFETY,

THIS APPLIANCE MUST BE PROPERLY

GROUNDED.

PREFERRED

METHOD

Ensure proper ground

exists before use

The power cord of this appliance should be equipped

with a three-prong (grounding) plug which mates with

a standard three-prong grounding wall receptacle to

reduce the possibility of electric shock hazard from

this appliance.

The customer should have the wall receptacle and

circuit checked by a qualified technician to be sure

the receptacle is properly grounded.

When connecting the cord of this cooktop to a

standard two-prong wall receptacle, it is the personal

responsibility and obligation of the customer to have

it replaced with a properly grounded three-prong wall

receptacle.

DO NOT, UNDER ANY CIRCUMSTANCES, CUT OR

REMOVE THE THIRD (GROUND) PRONG FROM

THE POWER CORD.

A word about Ground Fault Circuit Interrupters –

Ground Fault Circuit Interrupters are not required or

recommended for gas range receptacles.

Ground Fault Circuit Interrupters are devices that

sense leakage of current in a circuit and

automatically switch off power when a threshold

leakage level is detected.

These devices must be manually reset by the

customer.

The National Electrical Code requires the use of

Ground Fault Circuit Interrupters in kitchen

receptacles installed to serve countertop surfaces.

Performance of the cooktop will not be affected if it is

operated from a Ground Fault Circuit Interrupters

protected circuit but occasional nuisance can occur.

3. ELECTRICAL CONNECTIONS

INSTALLATION INSTRUCTIONS

+ 22 hidden pages