LG LRH7160D-E1 Owner’s Manual

OWNER’S MANUAL

Hybrid Digital Video Recorder

Please read this manual carefully before operating your set and retain it for future reference.

MODELS

LRH7160D Series LRH7080D Series

1208 (V1.0)

Safety Information

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

FCC WARNING: This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.

REGULATORY INFORMATION: FCC Part 15

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

• A suitable conduit entries, knock-outs or glands shall be provided in the cable entries of this product in the end user.

• Caution: Danger of explosion if battery is incorrectly replaced. Replaced only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions.

• Holes in metal, through which insulated wires pass, shall have smooth well rounded surfaces or shall be provided with brushings.

This Class A digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

Warning: Do not install this equipment in a confined space such as a bookcase or similar unit.

Warning: Wiring methods shall be in accordance with the National Electric Code, ANSI/NFPA 70.

Warning: This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

Warning: To reduce a risk of fire or electric shock, do not expose this product to rain or moisture.

Caution: This installation should be made by a qualified service person and should conform to all local codes.

Caution: To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.

Caution: The apparatus should not be exposed to water (dripping or splashing) and no objects filled with liquids, such as vases, should be placed on the apparatus.

Caution:

This product employs a Laser System. To ensure proper use of this product, please read this owner’s manual carefully and retain it for future reference. Should the unit require maintenance, contact an authorized service center. Use of controls, adjustments, or the performance of procedures other than those specified herein may result in hazardous radiation exposure. To prevent direct exposure to laser beam, do not try to open the enclosure.

To disconnect power from mains, pull out the mains cord plug. When installing the product, ensure that the plug is easily accessible.

LG Electronics hereby declares that this/these product(s) is/are in compliance with the essential requirements and other relevant provisions of Directive 2004/108/EC, 2006/95/EC, and 2009/125/ EC.

European Standards Centre: Krijgsman 1, 1186 DM Amstelveen The Netherlands

Safety Information

Disposal of your old appliance

1. When this crossed-out wheeled bin symbol is attached to a product it means the product is covered by the European Directive 2002/96/EC.

2. All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities.

3. The correct disposal of your old appliance will help prevent potential negative consequences for the environment and human health.

4. For more detailed information about disposal of your old appliance, please contact your city office, waste disposal service or the shop where you purchased the product.

EEE Compliance with Directive. (for Turkey only)

Safety way to remove the battery or the battery from the equipment:

Remove the old battery or battery pack, follow the steps in reverse order than the assembly. To prevent contamination of the environment and bring on possible threat to human and animal health, the old battery or the battery put it in the appropriate container at designated collection points. Do not dispose of batteries or battery together with other waste. It is recommended that you use local, free reimbursement systems batteries and accumulators. The battery shall not be exposed to excessive heat such as sunshine, fire or the lile.

Disposal of waste batteries/accumulators

1. When this crossed-out wheeled bin symbol is attached to batteries/accumulators of Your product it means they are covered by European Directive 2006/66/EC.

2. This symbol may be combined with chemical symbols for mercury(Hg), cadmium(Cd) or lead(Pb) if the battery Contains more that 0.0005% of mercury, 0.002% of cadmium or 0.004% of lead.

3. All batteries/accumulators should be disposed separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities.

4. The correct disposal of Your old batteries/ accumulators will help to prevent potential negative consequences for the environment, animal and human health.

5. For more detailed information about disposal of Your old batteries/accumulators, please contact Your city office, waste disposal service or the shop where You purchased the product.

IMPORTANT SAFETY INSTRUCTIONS

Safety Information

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or groundingtype plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

Safety Information

Safety warnings and Cautions

The following are warnings and cautions for the safety of the users and for the prevention of any property damage. Please read the following

Safety Information

carefully.

WARNING

• Turn off the system before installation. Do not plug in several electric devices to the same outlet.

- This may cause heating, fire, or electric shock.

• Do not place any liquid container on the system, such as water, coffee, or other beverage.

- If liquid is poured onto the system, it can cause a system breakdown or fire.

• Prevent the power cable from being severely bent or having pressure exerted on it by a heavy object.

- This may cause fire.

• Clean the dust around the system on a regular basis. When cleaning the system, always use a dry cloth. Do not use a wet cloth or other organic solvents.

- This may damage the surface of the system and can cause a system breakdown or electric shock.

• Avoid any place with moisture, dust, or soot.

- This can cause fire or electric shock.

• When pulling the power cable from the plug, do so gently. Do not touch the plug with wet hands and avoid using the plug if the holes in the outlet are too loose.

- This may cause fire or electric shock.

• Do not attempt to disassemble, repair, or modify the system on your own. It is extremely dangerous due to the high voltage running through the system.

- This may cause fire, electric shock, or serious injury.

• Check for any danger signs such as a moist floor, a loosened or damaged power cable, or an unstable surface. If you encounter any problems, ask your dealer for assistance.

- This may cause fire or electric shock.

• Keep a distance of at least 15 cm between the back of the system and the wall for the cables connected to the system otherwise, they may be bent, damaged, or cut.

- This may cause fire, electric shock, or injury.

• Install the system in a cool place without direct sunlight and always maintain room temperature. Avoid candlelight and heat generating devices such as heaters. Keep the system away from places where many people pass.

- This may cause fire.

• Install the system on a plain surface with sufficient air ventilation. Do not place the system on an elevated surface.

- This may cause system breakdown or serious injury.

• The power outlet must be placed on the ground, and the voltage range must be within 10 % of the voltage rate. Do not use the same outlet with a hair dryer, iron, refrigerator, or any heating appliances.

- This may cause fire, over heating or electric shock.

• When the system’s battery is depleted, replace it with the same or equivalent type of battery specified by the manufacturer. Depleted batteries should be discarded according to the manufacturer’s instructions.

- This may cause an explosion.

• If the system’s HDD exceeds its life span, you may not be able to recover any data stored inside the HDD. If the video on the system screen appears ‘damaged’ while playing a recording stored inside the system’s HDD, it must be replaced with a new one. Ask for an engineer’s assistance for HDD replacement from your dealer.

- LG Electronics is not responsible for deleted data caused by user mishandling.

• PLEASE DO NOT MOUNT OR UN-MOUNT HDDs WHILE SYSTEM IS POWERED ON.

- This may cause system breakdown.

Safety Information

CAUTION

Please beware of the following precautions before installing the DVR.

• Avoid positioning the product in any place where the unit may come into contact with moisture, dust, or soot.

• Avoid placing in direct sunlight or near heating appliances.

• Keep the product away from electric sparks or magnetic substances.

• Do not place any conductive material through the ventilation grills.

• Keep the system turned off before installation.

• Ensure enough space is left for cable connections.

• Place the system on a solid surface with sufficient air ventilation. Avoid any surface that vibrates.

• Placing the system near electronic devices such as a radio or a TV may cause the product to breakdown.

• Do not disassemble the product without seeking assistance from LG Electronics.

• Do not place any heavy object on the system.

• Prevent any substances from being inserted into the system.

- This may cause system breakdown.

• Install the system in a place with sufficient air ventilation.

- Keep at least 15 cm distance between the back of the system and the wall, and at least 5 cm distance between the side of the system and the wall.

• Do not install the system in a place with high magnetic, electric wave, or wireless devices such as a radio or a TV.

- Do not install the system in a place with magnetic objects, electric frequencies, or vibration.

• Do not place any heavy object on the system.

- This may cause system breakdown.

• Install the system on a stable, level surface.

- The system may not operate properly.

• Install the system in a place with appropriate moisture and temperature levels.

- Avoid installing the system in a place with high (over 40 °C) or low (under 0 °C) temperature.

• The system can be damaged from a strong impact or vibration. Avoid throwing objects within the vicinity of the system.

• Avoid direct sunlight or any heating appliances.

- Recommended operating temperature is over 0 °C (32 °F).

• Ventilate the air inside the system operation room, and tighten the system cover firmly.

- System breakdown may be caused by an inappropriate environment. It is recommended to use AVR (Automatic Voltage Regulator) for a stable power supply. It is recommended to coil the core-ferrite around the connector of the system to avoid electromagnetic interference.

• The outlet must be placed on the ground.

• If there is strange sound or smell, unplug the power cable immediately and contact the service center.

- This may cause fire or electric shock.

• In order to maintain stable system performance, have your system checked regularly by the service center.

- LG Electronics is not held responsible for system breakdown caused by user mishandling.

- There is a risk of explosion if a battery is replaced by an incorrect type. Dispose of used batteries according to the instructions.

• Do not overturn the product during use.

Safety Information

Contents

Safety Information

3 IMPORTANT SAFETY INSTRUCTIONS

Preparation

8 Introduction

8 Features

8 Accessories

9 Front Panel

11 Rear Panel

12 Remote Control

Screen on the Main Monitor

20 Main Monitor Screen

21 Moving the Channel's Position

21 Selecting the Main Monitor screen mode

22 Selecting the Spot Monitor screen mode

22 Changing the order of cameras

22 PTZ Camera Control

23 Using the Digital Zoom function

24 Export the recorded data

25 Viewing the System Log List

25 Viewing System Information

26 Conﬁguration menu

27 System settings

27 Properties

27 TCP/IP v4

27 TCP/IP v6

28 Network

28 Network Streaming

29 Date/Time

29 NTP

29 Controller

29 Update

30 Backup

Installation

13 Connections

13 Precautions

13 Basic Connection Overview

14 Connecting Camera

14 Connecting the video distributor

14 Connecting Display device

15 Connecting Audio device

15 Connecting USB device

15 Connecting E-SATA device

16 Connecting ATM/POS

16 Connecting Network

17 Connecting RS-485 device

17 Connecting Alarm Input and Alarm Output

19 HDD INSTALLATION

19 Note for Hard Disk Drive

19 Installing the Hard Disk Drive

19 Replacing the Hard Disk Drive

19 Recommended HDD

20 System Operation

20 System Shutdown

20 General Explanation of the Live

31 Device settings

31 Camera

32 PTZ

32 IP Device

33 ATM/POS

33 Storage

34 Display settings

34 OSD

34 Sequence

34 Video Adjustment

35 Record settings

35 Normal Schedule Recording

35 To Set a Recording Schedule for a Typical Day

of the Week (Normal Schedule)

36 To Set a Recording Schedule for a Special Day

(Special Schedule)

36 Copying the Recording Schedule

37 Normal

37 Sensor

37 Motion

37 Text

38 Instant/Panic

38 Event settings

38 Sensor

38 Motion

39 ATM/POS Data Format

Contents

39 Event Popup

40 Notiﬁcation

40 Mail

40 Emergency

41 SNMP

41 Output

41 Buzzer

42 User settings

42 Group Authority

42 User

43 Setup Wizard settings

43 Step 1

43 Step 2

44 Step 3

44 Step 4

44 Step 5

Operation

55 Connect to the DVR

55 Connect the group device

55 Disconnect the site name or group name

55 Using the Live function

58 Using the Search function

60 Using the Remote Setup function

65 Using the Export function

66 Using the E-Map function

67 Using the Multiple Window function

67 Using the Protect function

68 Additional Programs

68 Emergency Agent Program

69 Export Viewer Program

70 Web Viewer Program

Troubleshooting

45 Instant Recording

45 Panic Recording

46 Instant Playback

46 Search and Playback

46 Date and Time Search

46 Event Search

47 Bookmark/Protect Search

47 ATM/POS Search

48 Export Search

48 Smart Search

49 Functions Available During Playback

50 Using the playback control menu

50 Using the Protect function

LG Network Client Program

51 Introduction

51 Recommended PC Requirements

51 Before install the program

Appendix

75 Recommended Devices

75 Recommended USB Memory list

75 Recommended External Device list

75 Recommended CD/DVD Media list

76 Supported function list for device

76 Supported PTZ Camera list

76 Supported IP Camera Audio/Video Codec

77 Time zones

78 Factory Default Conﬁguration Settings

85 Recording Time Table (250GB HDD)

88 Speciﬁcations

51 Getting Started

51 Install the LG Network Client on your PC

51 Starting the LG Network Client

52 LG Network Client Overview

54 Operation and settings

54 Register the Site Name or Group Name

Preparation

2 Preparation

Preparation

Introduction

Model LRH7160D (16 Channel) is used for the description, operation and details provided in this operating guide.

Features

• Stable embedded Linux operating system.

• Journal filing system for HDD file recovery following power

recovery.

• Small file sizes with H.264 compression.

• Internal storage expandable to 12 TB. (Expandable if new high

capacity HDD is launched)

• NTSC and PAL selectable video format.

• Full real-time recording.

NTSC

PAL

• Various recording resolutions and quality levels.

NTSC D1(704x480), Half D1(704x240), CIF(352x240)

PAL D1(704x576), Half D1(704x288), CIF(352x288)

- 5 step quality level (Highest, High, Standard, Low, Lowest).

• Easy operation using various user interface & user friendly GUI.

- Optical mouse, Full function IR remote controller

• Powerful multiplex function.

- Simultaneous live display, recording, playback, network

• Various search function.

- Date/time search (calendar search), Event search, Bookmark/

• Pre-alarm recording (Up to 1 minute).

• Motion event recording and preview test function of motion

sensitivity.

• Recording image rate & quality adjustment per individual camera.

• Powerful record scheduling.

• Instant playback in live mode.

• Perfect audio/video synchronization.

• Automatic backup by schedule.

• Image authentication (Watermark).

• Three USB 2.0 ports for backup interface.

Up to 480 IPS @ 704x480, LRH7160D Series Up to 240 IPS @ 704x480, LRH7080D Series

Up to 400 IPS @ 704x576, LRH7160D Series Up to 200 IPS @ 704x576, LRH7080D Series

transmission, back-up.

Protect search, ATM/POS search, Export search, Smart search.

• Setup configuration export/import with USB memory stick.

• Easy system S/W update with USB memory stick or network.

• Clients S/W can manage max 200 DVR servers.

• Max five clients can access one DVR server simultaneously.

• Network bandwidth throttle.

- Automatically adjust a bandwidth according to network speed status of unit.

• Remote alarm notification via client software or E-mail.

• Time and date sync from NTP server.

• Daylight saving mode.

• Covert camera protection.

• Support Gigabit Ethernet.

• E-SATA storage interface.

• Two-way audio.

• Text Input for ATM and POS device.

• User management (User level control).

• PTZ Control.

- Dome camera telemetry control (Dome OSD control).

Accessories

CD (Software

and Owner's

Manual)

Mouse

Remote

Control

AAA type

batteries

Screws

Rack Mount

Bracket

Power Plug

Simple

Manual

Preparation

OSDNET

HDD

ALARM

BACK UP

PTZ3FOCUS+4IRIS+

SHIFT

INFO6ALM.OFF7FOCUS -8IRIS -

LOG

10/0

TEXT OFF11SET12CLEAR

COPY14MARK15MOVE16TOUR

LOG-IN VIEW CAM BACK

REC

SEARCH SETUP

Front Panel

Front of the LRH7160D series

a b c d e f g h c i h

OSDNET

PTZ3FOCUS+4IRIS+

HDD

ALARM

BACK UP

INFO6ALM.OFF7FOCUS -8IRIS -

LOG

TEXT OFF11SET12CLEAR

10/0

COPY14MARK15MOVE16TOUR

SHIFT

Preparation

SEARCH SETUP

LOG-IN VIEW CAM BACK

REC

j k l m n o p q r s

Front of the LRH7080D series

a b c d e f g h c i h

OSDNET

PTZ3FOCUS+4IRIS+

HDD

ALARM

BACK UP

j k l m n o p q r s

a 1 b

(Power): Turns DVR on or off. Press and hold for more than 2 seconds to turn on or off.

Playback Control Buttons

INFO6ALM.OFF7FOCUS -8IRIS -

LOG0TEXT OFF SET CLEAR

COPY MARK MOVE TOUR

SHIFT

SEARCH SETUP

LOG-IN VIEW CAM BACK

REC

•M: Pauses playback.

•

c, C/aM

•

: Playback or reverse playback of recorded images.

ad v, V/Md

: Searches the recorded images in reverse or skips the recorded images.

: Forward searches the recorded images or skips the recorded images.

•Z: Stops playback.

Front panel release button : Press these buttons to separate the front panel for HDD installation.

Indicator

• NET: Blinks when the network is connected.

• HDD: Lights when the HDD is accessed.

• ALARM: Lights when the alarm out is in progress.

• BACK UP: Lights when the data back up is in progress.

Preparation

Channel Buttons: You can input a number with channel buttons. You can also use the channel buttons for sub-function with SHIFT

button (11 to 16 buttons of 8 channel DVR are used for sub-function without SHIFT button.).

• The LED in the button indicates the status as follows:

- Off: The current status is for live mode.

- Red: Recording mode.

- Blinks when an event occurs.

• Sub-functions

Preparation

Button number Function Description

1 OSD Accesses or minimizes the System Control Bar (OSD).

2 PTZ Switches this unit to PTZ mode to control the connected PTZ camera.

3/7

4/8 IRIS - / IRIS + Adjust iris position.

5 INFO Displays the system information.

6 ALM.OFF

9 LOG Displays the System Log List.

10 TEXT OFF Displays or disappears the text information if the recording data includes text data.

11 SET Registers the PTZ camera’s preset position.

12 CLEAR Deletes a memorized preset position.

13 COPY Displays the export menu.

14 MARK Sets the mark point for recording search.

15 MOVE Moves the camera to the preset position.

16 TOUR Tours all registered preset positions in the camera.

Remote Sensor: Point the remote control here.

SHIFT button: If you use the Sub-function of the channel button, the button is activated.

ZOOM + / -: Zooms in/out on playback window.

Arrow and OK Buttons

•

wsad

• OK: Confirms menu selections.

Disc Tray: Insert a disc here.

OPEN: Opens or closes the disc tray.

LOG-IN: Displays the User Log-In dialog box or logs out.

SEARCH: Displays the search menu.

SETUP: Displays the setup menu.

VIEW: Displays the split mode menu for MAIN Monitor and SPOT Monitor.

CAM: Displays the Monitor menu to set the first camera channel.

USB Port: Connects an external USB device for backup or playback.

BACK: Exits the menu or returns to the previous screen.

REC: Starts or stops instant recording.

: Select or move between the menu options.

FOCUS -

/ FOCUS +

Adjusts focus position.

Cancels alarm activation and returns the system to the condition before the alarm was activated.

Rear Panel

Rear of the LRH7160D series

a b c d

e f g h i j f k l m n o

Preparation

Rear of the LRH7080D series

a b c d

e f g h i j k l m n o

VIDEO INPUT: Connect the camera’s video output to these BNC connectors.

LOOP OUT: The signal from VIDEO INPUT connector is looped out to this connector.

RELAY-OUT Terminals: Output terminals for alarm (relay) signal.

Power Cord Inlet (AC IN): Connect the power plug.

AUDIO OUT 1 / 2: Connect to an active speaker with a built-in amplifier.

AUDIO IN: Connect the audio output of an external device.

ALARM-IN Terminals: Input terminals for alarm (relay) signal.

ATM/POS: Used to connect to a ATM/POS device.

VGA: Connect a VGA monitor.

SPOT-OUT (BNC Type Connector): Connect to spot monitor or display device.

HDMI: Connect to monitor or display device with HDMI inputs. (Interface for digital audio and video)

LAN Ports: Connect the ethernet 10/100/1000 Mbps network cable for controlling this unit via a PC network.

E-SATA: Connect the external SATA device.

USB Port: Connect an optional extension USB device.

RS-485 Terminals: Connect RS-485 compatible cameras.

Preparation

Remote Control

Preparation

Button Description

POWER (1)

VIEW

CAM

ALM.OFF

OSD

SETUP

wsad

COPY

MARK

PAUSE (M)

STOP (Z)

REC (X)

c, C/aM

v, V/Md

Number Buttons

INFO

LOG

PTZ

TOUR

ZOOM + / -

FOCUS + / -

IRIS + / -

SET

CLEAR

MOVE

BACK

Turns DVR on or off.

Displays the User Log-In dialog box or logs out.

Set the appropriate DVR system ID to operate via the IR Remote Controller when using the multiple DVR. Press the ID button then press the number button within 2 seconds to select the system ID of the DVR. If you set the system ID to “0”, you can control multiple DVR at the same time.

Displays the split mode menu for MAIN Monitor and SPOT Monitor.

Displays the Monitor menu to set the first camera channel.

Cancels alarm activation and returns the system to the condition before the alarm was activated.

Accesses or minimizes the system control bar.

Displays the setup menu.

Selects or moves between the menu options.

Confirms menu selections.

Copies the recording data to an external device.

Displays the search menu.

Sets the mark point for recording search. You can set the mark point during the single or multi channel playback of recorded data.

Pauses playback.

Stops playback.

Starts or stops recording.

Searches the recorded images in reverse or skips the recorded images.

Playback or reverse playback of recorded images.

Forward searches the recorded images or skips the recorded images.

Selects the PTZ preset number, ID or channel.

Displays the system information window.

Displays the System Log List window.

Switches this unit to PTZ mode to control the connected PTZ camera.

Tours all registered preset positions in the camera.

Zooms in/out on the playback window. If you press ZOOM(+) button during viewing a live channel in full screen mode or playing back a channel in full screen mode, the digital zoom function is activated.

Adjusts the focus of a camera.

Adjusts the iris of a camera.

Registers the PTZ camera’s preset positions.

Deletes a memorized preset position.

Moves the camera to the preset position.

Exits the menu or returns to the previous screen.

3 Installation

Connections

Installation

Precautions

• Depending on the camera and other equipment there are various ways to connect the unit. Please refer to the camera manual or manuals for other devices as necessary for additional connection information.

• Be sure to switch off the camera before installation and connection.

Basic Connection Overview

Connect the coaxial-type cameras

Connect the Monitor, DVR, VCR, or others.

Connect ATM/ POS unit.

Connect the alarm (relay).

Connect power cord.

Installation

Connect audio (line input).

Connect audio amplifier.

Connect alarm sensors.

Connect PTZ cameras, DVRs or keypads (optional).

Connect the external SATA device.

Connect an external USB device for backup or playback.

Connect a mouse device.

Connect network cable for client control or IP camera input.

Connect HDMI type monitor (MAIN or SPOT).

Connect BNC type monitor (SPOT).

Connect VGA monitor.

Installation

Connecting Camera

Connect the video output of your camera to the unit, using a standard 75 Ω video coaxial cable with BNC connector. LOOF OUT connector passes the video signal from VIDEO INPUT connector to connect to other device.

Camera connection

Installation

NOTE

If the distance between the camera and DVR is too long, the noise may be generated. In this case, we recommend you to ground DVR’s power and not to ground camera’s power.

Connecting Display device

This unit can be output simultaneously from the HDMI, VGA and SPOT OUT jack. The video signal connection between the DVR and the monitor.

VGA Monitor connection

Connect the VGA jacks on the rear of the unit to the corresponding input jacks on the TV or monitor using the VGA cable.

VGA Monitor connection

Connecting the video distributor

Connect the video signal of the camera to the input connector of the video distributor using a 75 Ω video coaxial cable with BNC connector. Connect the video output of the video distributer to the VIDEO INPUT connector of DVR using a using a 75 Ω video coaxial cable with BNC connector. Connect your monitor to the video output connector of the video distributor.

Connecting the video distributor

Video distributor

Monitor Monitor

NOTE

DVR

SPOT Monitor connection

Connect the unit to the SPOT monitor using 75 Ω video coaxial cables with BNC connector.

SPOT Monitor connection

• If the cable’s length is too long, DVR’s parts may be damaged due to an external static electricity. Before connecting the video cable, touch the end of the cable to DVR’s case to avoid the risk of static buildup.

• Please check the images via a monitor after installation of the video distributor.

HDMI Monitor connection

Connect the unit to the HDMI monitor using a HDMI cable (Type A, High Speed HDMITM Cable).

HDMI Monitor connection

MAIN SPOT

Connecting Audio device

Connect the AUDIO OUT jacks on the unit to the mono audio in jacks on your audio device.

Microphone and Speaker connection

Installation

USB Memory device

Insert the memory device into the USB port. The system automatically recognizes the device. The system software can be easily upgraded using a USB memory device.

USB External device

Connect the external device to the USB port. (Example: External HDD or other external storage.)

Mouse

Connect the USB mouse to operate the functions of the DVR.

Installation

Connecting USB device

USB device connection

Connecting E-SATA device

You can use E-SATA storage for data back-up or recording.

E-SATA device connection

Installation

Connecting ATM/POS

Connect the ATM/POS unit to the ATM/POS port.

ATM/POS device connection

Installation

Connecting Network

You can control and monitor the system via network. With the remote control (monitoring), you can change the system configuration or monitor the image via network. After the installation, check the network settings for the remote control and monitoring work.

Network connection

Broadband

Router

Broadband

Service

NOTE

• The following device has been tested and compatibility is ensured. When you use the multiple ATM/POS device, use the recommended device.

- AVE Products

› VSI-PRO: Video serial interface

› Regcom: RS-485 networker

› Hydra: RS-485 to RS-232 converter

• The installation and connection work should be done by qualified service personnel or system installers and should be conformed to all local codes.

LAN connection

Connect the LAN port to an available 10/100/1000 base-T port with a straight ethernet cable (not supplied). The NET indicator on the front panel will be lit.

IP Camera connection

Connect the IP camera. After the installation, check the IP camera settings on the setup menu.

Automatic network configuration

The DVR can automatically obtain and configure the network interface via DHCP.

Manually configure network

The DVR may be manually configured by assigning an IP address, subnet mask, gateway and DNS.

NOTE

This unit can be supported IPv4 and IPv6 network.

Installation

Connecting RS-485 device

This DVR has two data terminals. Use this port to connect PTZ cameras, DVRs or keypads (optional).

RS-485 Terminal Description

D - (DATA -) Data Transmission/Reception

D + (DATA +) Data Transmission/Reception

GND Shield

Connecting the PTZ device

Connecting the PTZ serial communication lines to the RS-485 terminal.

PTZ device connection

Connecting LKD1000 controller

Connect the LKD1000 controller to control the DVR. (Refer to the manuals of the LKD1000 controller for more details.) The LKD1000 controller has to be connected to the 2 (DATA 2) port as shown illustration. If you connect the LKD1000 controller to the 1 (DATA 1) port, the LKD1000 controller will not be activated.

LKD1000 controller connection

Installation

PTZ units

(RS-485 type)

PTZ units

(RS-485 type)

NOTE

• When connecting lines, connect the “D -” of the DVR to “RX -” of the PTZ unit and “D +” of the DVR to “RX +” of the PTZ unit correctly.

• Recommended initial data are 9600 Baud Rate, 8 Data bits, 1 Stop bit and No parity.

• When connecting PTZ cameras to DVRs it is necessary to set the setup menu for this unit according to the RS-485 settings of the camera and DVRs.

TX+TX-

LKD1000 Controller

NOTE

Do not connect a PTZ camera and LKD1000 controller to the D1 or D2 port at the same time. It may cause a malfunction.

Connecting Alarm Input and Alarm Output

Alarm terminals are used to connect the alarm devices such as sensors, door switches, etc.

Alarm Input

You can connect up to 16 alarm sensors (LRH7080D: 8 alarm sensors). Each alarm sensor should be connected with G (GND). The signal state is adjustable to N/O (Normal Open) or N/C (Normal Close) through the setup menu.

Installation

Sensor input connection

Alarm Output

Connect the alarm device to the alarm output. Alarm signal outputs when an event occur.

Alarm output connection

Alarm device

Alarm sensor Alarm sensor

Terminal No. Description

1 Sensor Input 1

2 Sensor Input 2

3 Sensor Input 3

4 Sensor Input 4

G Ground

5 Sensor Input 5

6 Sensor Input 6

7 Sensor Input 7

8 Sensor Input 8

G Ground

9 Sensor Input 9

10 Sensor Input 10

11 Sensor Input 11

12 Sensor Input 12

G Ground

13 Sensor Input 13

14 Sensor Input 14

15 Sensor Input 15

16 Sensor Input 16

G Ground

Terminal No. Description

G Ground

1 Alarm Output 1

2 Alarm Output 2

3 Alarm Output 3

4 Alarm Output 4

NOTE

The internal switching relays are rated for 0.3 A at 125 V AC or 1 A at 30 V DC. If the electric current is higher than that the unit can be damaged.

Installation

HDD INSTALLATION

Note for Hard Disk Drive

The internal hard disk drive (HDD) is a fragile piece of equipment. Please follow the guidelines below when using the DVR to protect against possible HDD failure. We recommend that you back up your important recordings onto an external backup device in order to prevent accidental loss.

Make sure that the power is turned OFF when attaching or removing the HDD.

• Do not move the DVR while the power is on.

• Do not use the DVR in excessively hot or humid places, or in

places that may be subject to sudden changes in temperature. Sudden changes in temperature can cause condensation to form inside the DVR. This can be a cause of HDD failure.

• While the DVR is switched on, do not unplug from the wall socket or switch the electricity off from the breaker switch.

• If there’s a power failure while the DVR is on, some data on the HDD may be lost.

• Do not drop the HDD. Also do not put the metallic object such as coins or screwdrivers into the HDD tray.

• When a power failure occurs during recording, avoid adding, replacing or transporting the HDD as the recorded data may be erased. In this case, turn the power back on to boot up the unit normally with the HDD that was being used at the time of the power failure attached. Then add, replace, or transport the HDD.

• The HDD is very delicate. Handle the HDD with care and follow the precautions below because even a tiny shock may damage the internal components of the HDD.

- Do not place the HDD on the desk or table directly. Put a thick cushion under the HDD because even a small shock may damage the internal components of the HDD.

- Do not use an electric screwdriver. Vibrations and shocks caused by an electric screwdriver may damage the internal components of the HDD.

- When replacing the HDD, do not knock the HDD with other components such as another HDD and the HDD tray.

- Do not knock the HDD with tools such as a driver when replacing the HDD.

• Protect the hard disk drives from static electricity.

Installing the Hard Disk Drive

6. Attach the hard disk mounting brackets with the screws.

7. Put HDD Rack in and fasten the screws.

8. Assemble the front panel.

9. When you turn the power of the unit on, the new HDD is detected and formatted automatically.

CAUTION

You should install the hard disk drive from 1 to 6 in order.

Replacing the Hard Disk Drive

Turn the power of the unit off and detach the power plug from the outlet.

1. Disassemble the front panel by pressing the release button on the front panel.

2. Loosen the screws of HDD Rack.

3. Pool the HDD Rack out.

4. Remove the screws and detach the hard disk mounting brackets from the units.

5. Install the new HDD.

6. Put HDD Rack in and fasten the screws.

7. Assemble the front panel.

8. After replacing the hard disk drive, insert the power plug into the outlet and turn the power of the unit on. The new HDD is detected and formatted.

automatically.

NOTE

Do not use an electric screwdriver to fix them.

Recommended HDD

For the latest recommended HDD list, please visit http://www.lgesecurity.com

NOTE

If you do not use the recommended HDD, the system may not be operated normally.

Installation

You can install up to 6 HDDs.

Improper installation or setup may disturb HDD recognition or normal product operation. So you should consult with an expert from the store where the product was purchased.

1. Disassemble the front panel by pressing the release button on the front panel.

2. Loosen the screws of HDD Rack.

3. Pool the HDD Rack out.

4. Remove the screws and detach the hard disk mounting brackets from the units.

5. Attach the HDD onto the hard disk mounting brackets with four screws.

Installation

System Operation

1. Turn on the unit. System booting will commence. The LG logo image will be displayed on the main monitor during the system booting.

2. When the booting is completed the live window will be

displayed. Click the icon on the system control bar or press

the LOGIN button on the remote control to display the log-in window.

3. Select a user name by using the mouse or arrow and the OK

Installation

button on the remote control or front panel. For the first time, you can select the ADMINISTRATOR user name only. You can register a new user with various access rights using the user setup menu.

4. Enter the password by using the virtual keyboard. (Note that the default administrator password is “000000”.)

5. Click the [OK] icon. You can see the live screen and operate the system.

NOTE

• This DVR is based on a VGA monitor using OSD. We recommend you to using the VGA monitor with this unit. If you use a composite monitor, the OSD quality may be low to read it.

• If the DVR is turned off accidently and then turned on again, the DVR may take a long time to be rebooted.

General Explanation of the Live Screen on the Main Monitor

Main Monitor Screen

a b c d e f g

Channel Number

Displays the channel number.

Channel Name

Displays the edited channel name.

Selected Channel

Displays the selected channel with red box.

Camera Status Icon

System Shutdown

1. First, you must stop playback and exit the setup menu. In playback, press STOP.

2. Press and hold 1 (POWER) button until the beep sounds and the logout window will be displayed.

3. Enter the password by using the virtual keyboard.

4. Click the [OK] icon. The system will shutdown.

Displays the PTZ camera status.

Displays the input audio status.

Displays the IP camera status.

Gold “C” indicates continuous recording.

Gold “I” indicates Instant recording.

Red “S” indicates sensor triggered recording.

Green “M” indicates motion detection recording.

Gray “N” indicates the channel is not being recorded.

Violet “T” indicates text event recording.

Quick Buttons

The Quick Buttons will appear when the mouse is moved to the camera's live screen. You can use the following functions by clicking it for the selected channel.

You can use the playback function.

You can use the digital zoom function.

You can control the PTZ Camera. (optional)

Live Screen

Displays the current surveillance live screen.

System Control Bar

Displays the CPU usage and Data traffic level of IP cameras.

Displays date and time.

( )

Search: Displays the search menu.

Alarm Off: Turns the alarm off.

Installation

Selecting the Main Monitor screen mode

You can select the live screen mode to display a full, 4-split, 6-split, 8-split, 9-split, 16-split, 17-split or 25-split screens on the main monitor.

1. Press VIEW or click icon in the system control bar.

2. Select [Main Monitor].

3. Select a screen mode.

Camera: Displays the Monitor menu to set the first camera channel.

Split mode: Displays the menu for selecting the screen division.

Video Export: Displays the export menu.

System Log: Displays the system log list window.

System Information: Displays the system information window.

Setup: Displays the setup menu.

Minimizes the System Control Bar.

NOTE

• To display / minimize the system control bar

To display or minimize System Control Bar, press OSD after pressing the SHIFT button on the front panel or click in the System Control Bar.

• You can also use the system control's options by clicking the right button of the mouse on the Main Monitor screen.

• When data signal color of IP camera is changed yellow or red, reduce bit rate, frame rate, resolution and connections of IP camera.

Installation

Screen split mode

Sequence mode

• Full Screen Mode: You can view the live window in full screen mode.

• 4, 9, 16, 25, 1+5, 1+7 and 1+16 Split Mode: Displays selected split screens on the main monitor.

• Sequence: You can view all the channels in sequence. You cannot use sequence mode with the 25 split (LRH7080D series: 16 split).

4. Select [OK] and press OK to confirm your selection.

NOTE

To display the screen you want to watch in full screen mode, double click the desired channel.

Moving the Channel's Position

You can change the camera channel's position in a split screen of the Main Monitor.

1. Select a desired channel by clicking the left button of the mouse.

2. Drag and drop it to a desired location and the channel's position will be changed.

Installation

Selecting the Spot Monitor screen mode

You can select the live screen mode to full, 4-split, 9-split or 16-split screens on the spot monitor.

1. Press VIEW or click the icon in the system control bar.

2. Select [Spot Monitor].

3. Select a screen mode.

Installation

Screen split mode

Sequence mode

• Full Screen Mode: You can view the live window in full

screen mode.

• 4, 9 and 16 Split Mode: Displays selected split screens on the

spot monitor.

• Sequence: You can view all the channels in sequence. You

cannot use sequence mode with the 16 split (LRH7080D series: 9 split).

3. Select [OK] and press OK to confirm your selection.

Changing the order of cameras

You can change the order of the cameras shown on the monitor.

1. Press CAM or click the icon in the system control bar.

2. Select [Main Monitor] or [Spot Monitor] on the menu.

3. Select a camera number you want to set as first monitor.

- [Restore to Default] : Camera 1 is set in first monitor.

PTZ Camera Control

You can control the cameras connected via the data port of RS-485 terminal or Network. You must set the configuration between the PTZ camera and the DVR.

1. Select the PTZ camera channel on the main monitor you want to control.

2. Press PTZ or click the icon that appears when the mouse is moved to PTZ camera's screen. Virtual PTZ remote control is displayed on the main monitor.

3. Use each item to control the PTZ camera.

Button Function

Displays the PTZ control guide.

Displays the setup menu of the PTZ camera.

Minimizes PTZ virtual remote control.

Removes the PTZ virtual remote control.

Use to pan/tilt the camera.

You can select the Pan/Tilt/Zoom speed.

You can adjust the camera zoom.

You can adjust the focus of a camera manually.

You can adjust the iris of a camera manually.

Displays or disappear the preset control options in the virtual PTZ remote control

Displays the Selected Preset number.

To input the preset number.

To register preset positions.

4. Select [OK] and press OK to confirm your selection.

To delete a memorized preset position.

To move the camera to the preset position.

To start a preset tour.

Confirm the preset position.

NOTE

You can use some options by clicking the right button of the mouse in PTZ camera control mode.

• PTZ Control Guide: Shows the guide for using the mouse.

• Exit: Exits from the PTZ camera control mode.

Installation

Preset Settings

Preset position is the function to register camera monitoring positions (preset positions) associated with position numbers. By entering the position numbers, you can move cameras to the preset positions.

NOTE

To activate this function, you need to register the preset positions of the PTZ cameras.

To Register Preset Positions

1. Move the camera to a point you wish by using the

, , , buttons.

2. Press SET or click the icon.

3. Select the preset number you wish to register.

4. Press OK or click the icon.

The position and its number are memorized.

5. Repeat steps 1 to 4 to add additional positions.

NOTE

Preset numbers from 0 to 255 are available on this unit but the actual preset range differs depending on PTZ cameras.

To Tour The Preset Positions

You can tour all preset positions.

1. Press the TOUR button or Click the icon.

All registered preset positions in the camera will be selected and the camera position image will be switched on the active monitor.

2. You can stop the tour by pressing the TOUR

button or clicking the icon.

Setup for PTZ Cameras

You can adapt the camera to your requirements by setting up the respective items in menus.

1. Click the icon.

The setup menu appears in the selected window of the main monitor.

2. Use , , , , , , , and

buttons to set the options.

NOTE

• Refer to the manuals of the PTZ camera for more details.

• Some PTZ cameras may not operated properly with this unit.

• You cannot control the other functions when the PTZ virtual

remote control is displayed.

Installation

Changing to a Picture in a Preset Position

The following function is available only with cameras provided with the preset function. The preset function makes the combination camera move to the programmed preset position. It is necessary to program preset positions for the combination camera beforehand.

1. Press the MOVE button or click the icon.

2. Use number buttons to enter the memorized preset position’s

index number then press OK or click the icon.

The camera moves to the preset position and the picture of the camera in that position appears on the monitor.

To Clear the Preset Position

You can clear a memorized preset position.

1. Press the CLEAR button or Click the icon.

2. Use number buttons to enter the memorized preset index

number then press OK or Click the icon to

clear the preset positions.

NOTE

This function may not be available depending on PTZ cameras.

Using the Digital Zoom function

You can enlarge the current screen 2 times using the digital zoom function on one live channel with full screen mode or one channel playback with full screen mode.

1. Press ZOOM(+) button during viewing a live channel in full screen mode or playing back a channel in full screen mode.

2. You can use the zoom screen as following.

• You can move the position of the zoom screen by using the

w/s/a/d

• You can move the zoom screen by using the mouse. Drag &

drop a point to the specific point to move the zoom screen.

3. Press BACK button to exit.

NOTE

The zoom function is deactivated when below case.

• When double click the left mouse button.

• Press the specific channel or function button which front

panel of the unit.

• Press the STOP button during the playback.

You can use some options by clicking the right button of the mouse in the digital zoom mode.

• Digital Zoom Control Guide: Shows the guide for using the mouse.

• Exit: Exits from the digital zoom mode.

buttons.

Installation

Export the recorded data

This unit can manually copy recorded images and audio from builtin HDD to the external recording devices.

1. Press EXPORT or click the icon in the system control bar. The [Video Export] menu appears.

Installation

2. Set the [Start Date/Time] and [End Date/Time] to copy.

•

a/d/w/s

•

w/s

• OK: Selects option or confirms the setting.

3. Select the channel number and press OK. Repeat this step to select multi channels.

4. Select [Export to] then press OK.

5. Use

w/s

6. Press OK to confirm it.

7. Click the [Export] icon to start exporting. The exported data will be authorized by the unit before saving and it can only be played back with the exclusive player.

: Moves to the options.

: Sets the selected option.

to select a target device to export.

NOTE

• Check the export device before you proceed.

• You can also use the EXPORT button on the front panel for

export function.

• You can export the recorded data only in the live mode.

• If you use the external device, the external device has to be

formatted on this unit.

1. Connect the external device to the USB port on the front or the rear of the DVR.

2. Select the [Format] icon then press OK. Confirm window is displayed after format is completed.

3. Select [OK] and press OK to close the window.

• Check the size of the selected data and free space of the external device. If the device does not have enough space, create space on the device or erase the previously stored data.

• Export can not be executed while the backup is in progress.

• You can search the exported data with the supplied viewer

software.

• When you export the recorded data, the video data, audio data, the system log and event log data will also be exported.

• When you export the recorded data the export viewer program will also be exported in the [ExportViewer] folder of the device. The exported data file name is made automatically as the [Channel name_export date_export time.exp] type.

• Do not remove the USB device while the export is in progress, it may cause a malfunction.

• The warning message appears for the conditions listed below.

- When the start date/time and end date/time are the same value.

- When the start date/time is later than the end date/time.

- The export media does not have enough space.

- When you set the time for data that does not exist.

• Anexternalmediahastobeformattedonthisunittoprevent

a malfunction.

• DVD+RWandDVD-RWdiscshavetobeinitializedbefore

using.

Installation

Viewing the System Log List

To view the system log list:

1. Press the LOG button or click the icon in the system control bar. The system log list window is displayed on the main

monitor.

2. Set the [Start Date/Time] and [End Date/Time] to copy.

•

a/d/w/s

•

w/s

• OK: Selects option or confirms the setting.

3. Use

a/d

4. Press the BACK button or click the [Close] button to exit the window.

: Moves to the options.

: Sets the selected option.

to see the previous or next log list.

Viewing System Information

To view system information:

1. Press the INFO button or click the icon in the system control bar. The system information window is displayed on the main

monitor.

Installation

• Ethernet 0 / 1: Displays the detail information of the

Network.

• HDD Information: Displays the detail information of the

HDD.

NOTE

Refer to the following system log list.

No. Log Message

1 Power On

2 Power Off

3 Login (Remote)

4 Logout (Remote)

5 Login (Local)

6 Logout (Local)

7 Configuration Changed

8 Configuration Imported

9 Factory Default Set

10 Power Recovery

11 Backup Started

12 Backup Finished

13 Backup Failed

14 Export Started

15 Export Finished

16 Export Failed

17 S/W Updated

18 HDD Damaged

19 HDD Added

20 HDD Deleted

21 HDD Formatted

22 HDD Changed

• Refresh: Updates the system information.

2. Press the BACK button or click the [Close] button to exit the window.

REC

Installation

Configuration menu

The features and options of the DVR are configured through the menu. The operations of this unit can be set via a menu displayed on the main monitor. You can select and set the operational conditions by using the buttons on the front panel and the remote control or using a Mouse connected to the unit.

First level

Second level

Third level

Installation

Setting the Menu Using the Front Panel Buttons or Remote Control Buttons

Front Panel

SETUP

1. Press SETUP to display the setup menu.

2. Use

w/s

display the submenu.

3. Use

w/s

to display the setting options.

4. Use

w/s

value.

5. Use

a/d

your selection.

6. Press BACK repeatedly to exit the Setup menu. If the save message appears, select [OK] and press OK to save the settings.

Remote Control

Use these buttons to select the menu options or adjust the options value.

Select the option or confirm the setting.

Return to the previous menu or level.

to select the desired menu item, then press OK to

to select the desired submenu item, then press OK

to select the desired option then press OK to set the

to select the desired setting then press OK to confirm

Description

Informations

Using a mouse to set a menu

Use the left or right mouse buttons to set the menu.

Button Function

• Use to select a required item or decrease the options value.

Left button

Right button Use to increase the options value.

1. Click the icon on the System control bar with the left mouse button to display a setup menu.

2. Click the desired option with the left mouse button to display the second or third level menu options.

3. Click the desired option with the left mouse button.

4. Set the selected options value.

5. Click the icon or click icon repeatedly to exit setup menu.

If the save message appears, click [OK] with the left mouse button to save the settings.

• If you double click the button, you can see the selected channel on the full screen.

NOTE

• When you operate the function menu by using the remote control and front panel buttons, both buttons are operated in the same way to control the function menu.

• To use other functions of number buttons on the front panel, follow the below steps.

1. Press SHIFT. The button indicator turns red.

2. Select the function button you want.

• All the operation explanations are based on using the remote control.

Installation

System settings

Properties

• DVR Name: Enter the DVR name by using alphabetic letter, numeric digit and symbols up to 21 characters.

• Language: Select a language for the setup menu and information display.

• Button Beep: Marks up to activate the button beep. The button beep is activated when using the buttons.

• Video Format: Selects the video format to NTSC or PAL according to your video system format. If you change the video format, the HDD is formatted with selected video format. After the HDD has been formatted, the confirmation message is displayed. Select [OK] and press OK. The system will reboot.

NOTE

All cameras must be disconnected before you change the video format to prevent malfunction.

TCP/IP v4

• Interface: Select a LAN port you want to use (Ethernet 0 or Ethernet 1).

• DHCP: Select this option when a DHCP server is installed on the network to allow IP address assignment. With this setting, the IP address is assigned automatically.

• IP Address: Enter the IP address.

• Subnet Mask: Enter the subnet mask address.

• Gateway: Enter the gateway address.

• Primary DNS: Enter the Primary domain name server that

translates the hostnames into IP address.

• Secondary DNS : Enter the Secondary DNS server address that backups the Primary DNS.

TCP/IP v6

Installation

• Resolution: Sets the output resolution of the HDMI video signal.

• Configuration Import: Import the DVRs configuration data from

the USB memory stick.

• Configuration Export: Export the configuration data from this DVR to the USB memory stick.

• Factory Default: You can reset the DVR to its original factory settings. Some options cannot be reset (date, time, daylight saving, time zone and user password settings).

• Interface: Select a LAN port you want to use (Ethernet 0 or Ethernet 1).

• Auto: Select this option to assign the IP address automatically.

• IP Address: Enter the IP address.

• Subnet Prefix Length: Enter the Subnet Prefix length.

An IPv6 prefix indicates the portion of the address used for routing or identifying an address range.

• Gateway: Enter the gateway address.

• Primary DNS: Enter the Primary domain name server that

translates the hostnames into IP address.

• Secondary DNS : Enter the Secondary DNS server address that backups the Primary DNS.

+ 63 hidden pages