LG LRH7080D-NH User Guide

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

FCC WARNING: This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.

REGULATORY INFORMATION: FCC Part 15

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

• A suitable conduit entries, knock-outs or glands shall be provided in the cable entries of this product in the end user.

• Caution: Danger of explosion if battery is incorrectly replaced. Replaced only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions.

• Holes in metal, through which insulated wires pass, shall have smooth well rounded surfaces or shall be provided with brushings.

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

Warning: Do not install this equipment in a confined space such as a bookcase or similar unit.

Warning: Wiring methods shall be in accordance with the National Electric Code, ANSI/NFPA

70.

Warning: This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

Warning: To reduce a risk of fire or electric shock, do not expose this product to rain or moisture.

Caution: This installation should be made by a qualified service person and should conform to all local codes.

Caution: To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.

Caution: The apparatus should not be exposed to water (dripping or splashing) and no objects filled with liquids, such as vases, should be placed on the apparatus.

Caution:

This product employs a Laser System. To ensure proper use of this product, please read this owner’s manual carefully and retain it for future reference. Should the unit require maintenance, contact an authorized service center. Use of controls, adjustments, or the performance of procedures other than those specified herein may result in hazardous radiation exposure. To prevent direct exposure to laser beam, do not try to open the enclosure.

The Power Plug is the disconnecting device. In case of an emergency, the Power Plug must remain readily accessible.

Disposal of your old appliance

1. This crossed-out wheeled bin symbol indicates that waste electrical and electronic products (WEEE) should be disposed of separately from the municipal waste stream.

2. Old electrical products can contain hazardous substances so correct disposal of your old appliance will help prevent potential negative consequences for the environment and human health. Your old appliance may contain reusable parts that could be used to repair other products, and other valuable materials that can be recycled to conserve limited resources.

3. You can take your appliance either to the shop where you purchased the product, or contact your local government waste office for details of your nearest authorised WEEE collection point. For the most up to date information for your country please see www.lg.com/global/recycling

Disposal of waste batteries/accumulators

1. This symbol may be combined with chemical symbols for mercury (Hg), cadmium (Cd) or lead (Pb) if the battery contains more than 0.0005% of mercury, 0.002% of cadmium or 0.004% of lead.

2. All batteries/accumulators should be disposed

3. The correct disposal of your old batteries/accumulators will help to prevent potential negative consequences for the environment, animal and human health.

4. For more detailed information about disposal of your old batteries/ accumulators, please contact your city office, waste disposal service or the shop where you purchased the product. (http://www.lg.com/global/sustainability/environment/takeback-recycling/global-network-europe)

Safety way to remove the battery or the battery from the equipment:

Remove the old battery or battery pack, follow the steps in reverse order than the assembly. To prevent contamination of the environment and bring on possible threat to human and animal health, the old battery or the battery put it in the appropriate container at designated collection points. Do not dispose of batteries or battery together with other waste. It is recommended that you use local, free reimbursement systems batteries and accumulators. The battery shall not be exposed to excessive heat such as sunshine, fire or the like.

Removal of waste batteries and accumulators

(Product with embedded battery ONLY)

In case this product contains a battery incorporated within the product which cannot be readily removed by end-users, LG recommends that only qualified professionals remove the battery, either for replacement or for recycling at the end of this product’s working life. To prevent damage to the product, and for their own safety, users should not attempt to remove the battery and should contact LG Service Helpline, or other independent service providers for advice.

CAUTION: Internal lithium battery in the unit should not be replaced by user because of danger of explosion if battery is incorrectly replaced ,and must be replaced with the same type battery by expert.

separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities.

Replacement of battery

SIMPLE MANUAL

Hybrid Digital Video Recorder

LRH7160D Series

LRH7080D Series

An extended Owner’s Manual that contains information on the advanced features is located on the CD-ROM provided in an electronic version. To read these files, you will need to use a Personal Computer (PC) equipped with a CD-ROM drive.

Model LRH7160D (16 Channel) is used for the description, operation and details provided in this operating guide.

Note: It is strongly recommended that you change the password of the administrator for the protection of the security of personal information. Do not leave 000000 as the default password. Make sure that you keep your password and write it down in a safe place so that you do not forget it.

Basic Connection Overview

Connect the Monitor, DVR, VCR, or others.

Connect ATM/POS unit.

Connect the coaxial-type cameras

Connect audio amplifier.

Connect PTZ cameras, DVRs or keypads (optional).

Connect audio (line input).

Connect the external SATA device.

Connect alarm sensors.

Connect an external USB device for backup or playback.

Connect VGA monitor.

Connect the alarm (relay)

Connect power cord.

LG Electronics hereby declares that this/these product(s) is/are in compliance with the essential requirements and other relevant provisions of Directive 2004/108/EC, 2006/95/EC, and 2011/65/EU.

Contact office for compliance of this product : LG Electronics Inc. EU Representative, Krijgsman 1, 1186 DM Amstelveen, The Netherlands

• Please note that this is NOT a Customer Service contact point. For Customer Service Information, see Warranty Card or contact the dealer that you purchased this product.

Connect BNC type monitor (SPOT).

Connect HDMI type monitor (MAIN or SPOT).

*MFL69441508*

Connect a mouse device.

Connect network cable for client control or IP camera input.

1512 (V6.0)

Front Panel and Remote Control

OSDNET

HDD

ALARM

PTZ3FOCUS+4IRIS+

SHIFT

INFO6ALM.OFF7FOCUS -8IRIS -

LOG

10/0

TEXT OFF11SET12CLEAR

OSDNET

HDD

ALARM

PTZ3FOCUS+4IRIS+

SHIFT

INFO6ALM.OFF7FOCUS -8IRIS -

LOG

10/0

TEXT OFF11SET12CLEAR

OSDNET

HDD

ALARM

PTZ3FOCUS+4IRIS+

SHIFT

INFO6ALM.OFF7FOCUS -8IRIS -

LOG

10/0

TEXT OFF11SET12CLEAR

OSDNET

HDD

ALARM

PTZ3FOCUS+4IRIS+

SHIFT

INFO6ALM.OFF7FOCUS -8IRIS -

LOG

10/0

TEXT OFF11SET12CLEAR

OSDNET

HDD

ALARM

PTZ3FOCUS+4IRIS+

SHIFT

INFO6ALM.OFF7FOCUS -8IRIS -

LOG

10/0

TEXT OFF11SET12CLEAR

OSDNET

HDD

ALARM

PTZ3FOCUS+4IRIS+

SHIFT

INFO6ALM.OFF7FOCUS -8IRIS -

LOG

10/0

TEXT OFF11SET12CLEAR

SHIFT

PTZ3FOCUS+4IRIS+

FOCUS+4IRIS+

IRIS+

FOCUS+4IRIS+

IRIS -

IRIS+

OSDNET

PTZ3FOCUS+4IRIS+

ALM.OFF7FOCUS -8IRIS -

PTZ3FOCUS+4IRIS+

FOCUS -8IRIS -

OSDNET

PTZ3FOCUS+4IRIS+

SHIFT

INFO6ALM.OFF7FOCUS -8IRIS -

10/0

TEXT OFF11SET12CLEAR

PTZ3FOCUS+4IRIS+

SHIFT

ALM.OFF7FOCUS -8IRIS -

SET12CLEAR

FOCUS+4IRIS+

SHIFT

FOCUS -8IRIS -

CLEAR

IRIS+

SHIFT

IRIS -

OSDNET

PTZ3FOCUS+4IRIS+

SHIFT

INFO6ALM.OFF7FOCUS -8IRIS -

LOG

10/0

TEXT OFF11SET12CLEAR

MARK15MOVE16TOUR

PTZ3FOCUS+4IRIS+

SHIFT

ALM.OFF7FOCUS -8IRIS -

10/0

TEXT OFF11SET12CLEAR

MOVE16TOUR

FOCUS+4IRIS+

SHIFT

FOCUS -8IRIS -

SET12CLEAR

TOUR

IRIS+

SHIFT

IRIS -

CLEAR

VIEW CAM BACK

REC

SEARCH SETUP

REC

SETUP

REC

CAM BACK

REC

BACK

REC

OSD

PTZ3FOCUS+4IRIS+

SHIFT

INFO6ALM.OFF7FOCUS -8IRIS -

LOG

10/0

TEXT OFF11SET12CLEAR

COPY14MARK15MOVE16TOUR

SHIFT

LOG-IN VIEW CAM BACK

REC

SEARCH SETUP

Setup Wizard

Front Panel

OSD2PTZ3FOCUS+4IRIS+

INFO6ALM.OFF7FOCUS -8IRIS -

LOG

TEXT OFF11SET12CLEAR

10/0

COPY14MARK15MOVE16TOUR

SHIFT

OSD

PTZ

FOCUS -

FOCUS+

IRIS -

IRIS+

INFO

ALM.OFF

LOG

TEXT OFF

10/0

SET

CLEAR

COPY

MARK

MOVE

TOUR

LOG-IN

SETUP

VIEW

CAM

BACK

REC

NET

HDD

ALARM

BACK UP

Remote Control

Description

Turns DVR on or off. Press and hold for more than 2 seconds to turn on or off.

Pauses playback.

Searches the recorded images in reverse or skips the recorded images.

Playback or reverse playback of recorded images.

Forward searches the recorded images or skips the recorded images.

Stops playback.

You can input a number with channel buttons. Note: You can also use the channel buttons for sub-function with SHIFT button.

- If you use the Sub-function of the channel button, the button is activated.

Accesses or minimizes the System Control Bar (OSD).

Switches this unit to PTZ mode to control the connected PTZ camera.

Adjusts focus position.

Adjust iris position.

Displays the system information.

Cancels alarm activation and returns the system to the condition before the alarm was activated.

Displays the System Log List.

- Displays or disappears the text information if the recording data includes text data.

Registers the PTZ camera’s preset position.

Deletes a memorized preset position.

Displays the export menu.

Sets the mark point for recording search.

Moves the camera to the preset position.

Tours all registered preset positions in the camera.

Zooms in/out on playback window.

•

wsad

: Select or move between the menu options.

• OK: Confirms menu selections.

Displays the User Log-In dialog box or logs out.

Displays the search menu.

Displays the setup menu.

Displays the split mode menu for MAIN Monitor and SPOT Monitor.

Displays the Monitor menu to set the first camera channel.

Exits the menu or returns to the previous screen.

Starts or stops instant recording.

• NET: Blinks when the network is connected.

• HDD: Lights when the HDD is accessed.

• ALARM: Lights when the alarm out is in progress.

• BACK UP: Lights when the data back up is in progress.

Opens or closes the disc tray.

To select the PTZ preset number, ID or channel.

Set the appropriate DVR system ID to operate via the IR Remote Controller when using the multiple DVR. Press the ID button then press the number button within 2 seconds to select the system ID of the DVR. If you set the system ID to “0”, you can control multiple DVR at the same time.

The Setup Wizard appears on the screen when you turn on the unit for the first time or select [Setup Wizard] on the Setup menu. You can set the system name, display language, date, time, network settings, recording schedule and recording mode on the initial setup wizard.

Step 1

Set system name and display language.

• System Name: Enter the system name by using alphabetic letter, numeric digit and symbols up to 21 characters.

• Language: Select a language for the setup menu and information display.

Step 2

Set date and time.

• Date: Select the current year, month and day.

• Time: Select the current time.

• Date Format: Select the date display format.

• Time Format: Select the time display format.

• Time Zone: Select the time zone in the area where the DVR is installed.

• Daylight Saving: Mark up when you use the daylight saving function.

• Daylight Saving Start: Select the Daylight Saving start time.

• Daylight Saving End: Select the Daylight Saving end time.

Step 3

Set network address for LAN ports.

• Interface: Select a LAN port you want to use (Ethernet 0 or Ethernet 1).

• DHCP: Select this option when a DHCP server is installed on the network to allow IP

address assignment. With this setting, the IP address is assigned automatically.

• IP Address: Enter the IP address.

• Subnet Mask: Enter the subnet mask address.

• Gateway: Enter the gateway address.

• Primary DNS: Enter the Primary domain name server that translates the hostnames into IP

address.

• Secondary DNS : Enter the Secondary DNS server address that backups the Primary DNS.

Step 4

Set recording schedule.

• Weekday: Sets the recording mode to weekday (Mon-Fri).

• Weekend: Sets the recording mode to weekend (Sat-Sun).

Step 5

Set recording mode for the Continuous and Event recording.

• Resolution: Selects the recording resolution.

• Quality: Selects the recording picture quality.

• Frame Rate: Selects the frame rate. The frame rate is the number of recorded frames per

second. According to resolution, the frame rate is set automatically.