LG LRH7080D-NH Owner’s Manual

OWNER’S MANUAL

Hybrid Digital Video Recorder

Please read this manual carefully before operating your set and retain it for future reference.

MODELS LRH7160D Series LRH7080D Series

*MFL67849056*

1512 (V8.0)

1 Safety Information

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

Safety Information

Caution:

This product employs a Laser System. To ensure proper use of this product, please read this owner’s manual carefully and retain it for future reference. Should the unit require maintenance, contact an authorized service center. Use of controls, adjustments, or the performance of procedures other than those specified herein may result in hazardous radiation exposure. To prevent direct exposure to laser beam, do not try to open the enclosure.

The Power Plug is the disconnecting device. In case of an emergency, the Power Plug must remain readily accessible.

LG Electronics hereby declares that this/ these product(s) is/are in compliance with the essential requirements and other relevant provisions of Directive 2004/108/EC, 2006/95/EC, and 2011/65/EU.

Contact oce for compliance of this product :

LG Electronics Inc. EU Representative, Krijgsman 1, 1186 DM Amstelveen, The Netherlands

Safety Information

This Class A digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

Warning: Do not install this equipment in a confined space such as a bookcase or similar unit.

Warning: Wiring methods shall be in accordance with the National Electric Code, ANSI/NFPA 70.

Warning: This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

Warning: To reduce a risk of fire or electric shock, do not expose this product to rain or moisture.

Caution: This installation should be made by a qualified service person and should conform to all local codes.

Caution: To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.

Caution: The apparatus should not be exposed to water (dripping or splashing) and no objects filled with liquids, such as vases, should be placed on the apparatus.

• Please note that this is NOT a Customer Service contact point. For Customer Service Information, see Warranty Card or contact the dealer that you purchased this product.

Safety Information

Safety warnings and Cautions

The following are warnings and cautions for the safety of the users and for the prevention of any property damage. Please read the following

Safety Information

carefully.

WARNING

• Turn off the system before installation. Do not plug in several electric devices to the same outlet.

- This may cause heating, fire, or electric shock.

• Do not place any liquid container on the system, such as water, coffee, or other beverage.

- If liquid is poured onto the system, it can cause a system breakdown or fire.

• Prevent the power cable from being severely bent or having pressure exerted on it by a heavy object.

- This may cause fire.

• Clean the dust around the system on a regular basis. When cleaning the system, always use a dry cloth. Do not use a wet cloth or other organic solvents.

- This may damage the surface of the system and can cause a system breakdown or electric shock.

• Avoid any place with moisture, dust, or soot.

- This can cause fire or electric shock.

• When pulling the power cable from the plug, do so gently. Do not touch the plug with wet hands and avoid using the plug if the holes in the outlet are too loose.

- This may cause fire or electric shock.

• Do not attempt to disassemble, repair, or modify the system on your own. It is extremely dangerous due to the high voltage running through the system.

- This may cause fire, electric shock, or serious injury.

• Check for any danger signs such as a moist floor, a loosened or damaged power cable, or an unstable surface. If you encounter any problems, ask your dealer for assistance.

- This may cause fire or electric shock.

• Keep a distance of at least 15 cm between the back of the system and the wall for the cables connected to the system otherwise, they may be bent, damaged, or cut.

- This may cause fire, electric shock, or injury.

• Install the system in a cool place without direct sunlight and always maintain room temperature. Avoid candlelight and heat generating devices such as heaters. Keep the system away from places where many people pass.

- This may cause fire.

• Install the system on a plain surface with sufficient air ventilation. Do not place the system on an elevated surface.

- This may cause system breakdown or serious injury.

• The power outlet must be placed on the ground, and the voltage range must be within 10 % of the voltage rate. Do not use the same outlet with a hair dryer, iron, refrigerator, or any heating appliances.

- This may cause fire, over heating or electric shock.

• When the system’s battery is depleted, replace it with the same or equivalent type of battery specified by the manufacturer. Depleted batteries should be discarded according to the manufacturer’s instructions.

- This may cause an explosion.

• If the system’s HDD exceeds its life span, you may not be able to recover any data stored inside the HDD. If the video on the system screen appears ‘damaged’ while playing a recording stored inside the system’s HDD, it must be replaced with a new one. Ask for an engineer’s assistance for HDD replacement from your dealer.

- LG Electronics is not responsible for deleted data caused by user mishandling.

• PLEASE DO NOT MOUNT OR UN-MOUNT HDDs WHILE SYSTEM IS POWERED ON.

- This may cause system breakdown.

Safety Information

CAUTION

Please beware of the following precautions before installing the DVR.

• Avoid positioning the product in any place where the unit may come into contact with moisture, dust, or soot.

• Avoid placing in direct sunlight or near heating appliances.

• Keep the product away from electric sparks or magnetic substances.

• Do not place any conductive material through the ventilation grills.

• Keep the system turned off before installation.

• Ensure enough space is left for cable connections.

• Place the system on a solid surface with sufficient air ventilation. Avoid any surface that vibrates.

• Placing the system near electronic devices such as a radio or a TV may cause the product to breakdown.

• Do not disassemble the product without seeking assistance from LG Electronics.

• Do not place any heavy object on the system.

• Prevent any substances from being inserted into the system.

- This may cause system breakdown.

• Install the system in a place with sufficient air ventilation.

- Keep at least 15 cm distance between the back of the system and the wall, and at least 5 cm distance between the side of the system and the wall.

• Do not install the system in a place with high magnetic, electric wave, or wireless devices such as a radio or a TV.

- Do not install the system in a place with magnetic objects, electric frequencies, or vibration.

• Do not place any heavy object on the system.

- This may cause system breakdown.

• Install the system on a stable, level surface.

- The system may not operate properly.

• Install the system in a place with appropriate moisture and temperature levels.

- Avoid installing the system in a place with high (over 40 °C) or low (under 0 °C) temperature.

• The system can be damaged from a strong impact or vibration. Avoid throwing objects within the vicinity of the system.

• Avoid direct sunlight or any heating appliances.

- Recommended operating temperature is over 0 °C (32 °F).

• Ventilate the air inside the system operation room, and tighten the system cover firmly.

- System breakdown may be caused by an inappropriate environment. It is recommended to use AVR (Automatic Voltage Regulator) for a stable power supply. It is recommended to coil the core-ferrite around the connector of the system to avoid electromagnetic interference.

• The outlet must be placed on the ground.

• If there is strange sound or smell, unplug the power cable immediately and contact the service center.

- This may cause fire or electric shock.

• In order to maintain stable system performance, have your system checked regularly by the service center.

- LG Electronics is not held responsible for system breakdown caused by user mishandling.

- There is a risk of explosion if a battery is replaced by an incorrect type. Dispose of used batteries according to the instructions.

• Do not overturn the product during use.

Safety Information

Contents

Safety Information

Preparation

8 Introduction

8 Features

8 Accessories

9 Front Panel

11 Rear Panel

12 Remote Control

20 Main Monitor Screen

21 Moving the Channel's Position

21 Selecting the Main Monitor screen mode

22 Selecting the Spot Monitor screen mode

22 Grouping channel

22 PTZ Camera Control

24 Using the Digital Zoom function

24 Export the recorded data

25 Viewing the System Log List

26 Viewing System Information

26 Conﬁguration menu

27 System settings

27 Properties

28 TCP/IP v4

28 TCP/IP v6

28 Network

29 Network Streaming

29 Date/Time

29 NTP

30 Controller

30 Update

30 Backup

Installation

13 Connections

13 Precautions

13 Basic Connection Overview

14 Connecting Camera

14 Connecting the video distributor

14 Connecting Display device

15 Connecting Audio device

15 Connecting USB device

15 Connecting E-SATA device

16 Connecting ATM/POS

16 Connecting Network

17 Connecting RS-485 device

17 Connecting Alarm Input and Alarm Output

19 HDD INSTALLATION

19 Note for Hard Disk Drive

19 Installing the Hard Disk Drive

19 Replacing the Hard Disk Drive

19 Recommended HDD

20 System Operation

20 System Shutdown

20 General Explanation of the Live

Screen on the Main Monitor

32 Device settings

32 Camera

32 PTZ

33 IP Device

34 ATM/POS

35 Storage

35 Display settings

35 OSD

35 Sequence

36 Video Adjustment

36 Record settings

36 Normal Schedule Recording

36 To Set a Recording Schedule for a Typical Day

of the Week (Normal Schedule)

37 To Set a Recording Schedule for a Special Day

(Special Schedule)

38 Copying the Recording Schedule

38 Normal

38 Sensor

39 Motion

39 Text

39 Instant/Panic

40 Event settings

40 Sensor

40 Motion

41 ATM/POS Data Format

41 Event Popup

Contents

41 Notiﬁcation

42 Mail

42 Emergency

42 SNMP

43 Output

43 Buzzer

44 User settings

44 Group Authority

44 User

45 Setup Wizard settings

45 Step 1

45 Step 2

46 Step 3

46 Step 4

46 Step 5

Operation

47 Instant Recording

57 Supported IP Camera Audio/Video Codec

58 Time zones

59 Factory Default Conﬁguration Settings

66 Recording Time Table (250GB HDD)

69 IP Live/Playback Speciﬁcations

69 Speciﬁcations

47 Panic Recording

48 Instant Playback

48 Search and Playback

48 Date and Time Search

48 Event Search

49 Bookmark/Protect Search

49 ATM/POS Search

50 Export Search

50 Smart Search

51 Functions Available During Playback

52 Using the playback control menu

52 Using the Protect function

Troubleshooting

Appendix

56 Recommended Devices

56 Recommended USB Memory list

56 Recommended External Device list

56 Recommended CD/DVD Media list

57 Supported function list for device

57 Supported PTZ Camera list

Preparation

2 Preparation

Preparation

Introduction

Model LRH7160D (16 Channel) is used for the description, operation and details provided in this operating guide.

Features

• Stable embedded Linux operating system.

• Journal filing system for HDD file recovery following power

recovery.

• Small file sizes with H.264 compression.

• Internal storage expandable to 12 TB. (Expandable if new high

capacity HDD is launched)

• NTSC and PAL selectable video format.

• Full real-time recording.

NTSC

PAL

• Various recording resolutions and quality levels.

NTSC D1(704x480), Half D1(704x240), CIF(352x240)

PAL D1(704x576), Half D1(704x288), CIF(352x288)

- 5 step quality level (Highest, High, Standard, Low, Lowest).

• Easy operation using various user interface & user friendly GUI.

- Optical mouse, Full function IR remote controller

• Powerful multiplex function.

- Simultaneous live display, recording, playback, network

• Various search function.

- Date/time search (calendar search), Event search, Bookmark/

• Pre-alarm recording (Up to 1 minute).

• Motion event recording and preview test function of motion

sensitivity.

• Recording image rate & quality adjustment per individual camera.

• Powerful record scheduling.

• Instant playback in live mode.

• Perfect audio/video synchronization.

• Automatic backup by schedule.

• Image authentication (Watermark).

• Three USB 2.0 ports for backup interface.

Up to 480 IPS @ 704x480, LRH7160D Series Up to 240 IPS @ 704x480, LRH7080D Series

Up to 400 IPS @ 704x576, LRH7160D Series Up to 200 IPS @ 704x576, LRH7080D Series

transmission, back-up.

Protect search, ATM/POS search, Export search, Smart search.

• Setup configuration export/import with USB memory stick.

• Easy system S/W update with USB memory stick or network.

• Clients S/W can manage max 300 DVR servers.

• Max five clients can access one DVR server simultaneously.

• Network bandwidth throttle.

- Automatically adjust a bandwidth according to network speed status of unit.

• Remote alarm notification via client software or E-mail.

• Time and date sync from NTP server.

• Daylight saving mode.

• Covert camera protection.

• Support Gigabit Ethernet.

• E-SATA storage interface.

• Two-way audio.

• Text Input for ATM and POS device.

• User management (User level control).

• PTZ Control.

- Dome camera telemetry control (Dome OSD control).

Accessories

CD (Software

and Owner's

Manual)

Mouse

Remote

Control

AAA type

batteries

Screws

Rack Mount

Bracket

Power Plug

Simple

Manual

Preparation

OSDNET

HDD

ALARM

BACK UP

PTZ3FOCUS+4IRIS+

SHIFT

INFO6ALM.OFF7FOCUS -8IRIS -

LOG

10/0

TEXT OFF11SET12CLEAR

COPY14MARK15MOVE16TOUR

LOG-IN VIEW CAM BACK

REC

SEARCH SETUP

Front Panel

Front of the LRH7160D series

a b c d e f g h c i h

OSDNET

PTZ3FOCUS+4IRIS+

HDD

ALARM

BACK UP

INFO6ALM.OFF7FOCUS -8IRIS -

LOG

TEXT OFF11SET12CLEAR

10/0

COPY14MARK15MOVE16TOUR

SHIFT

Preparation

SEARCH SETUP

LOG-IN VIEW CAM BACK

REC

j k l m n o p q r s

Front of the LRH7080D series

a b c d e f g h c i h

OSDNET

PTZ3FOCUS+4IRIS+

HDD

ALARM

BACK UP

j k l m n o p q r s

a 1 b

(Power): Turns DVR on or off. Press and hold for more than 2 seconds to turn on or off.

Playback Control Buttons

INFO6ALM.OFF7FOCUS -8IRIS -

LOG0TEXT OFF SET CLEAR

COPY MARK MOVE TOUR

SHIFT

SEARCH SETUP

LOG-IN VIEW CAM BACK

REC

•M: Pauses playback.

•

c, C/aM

•

: Playback or reverse playback of recorded images.

ad v, V/Md

: Searches the recorded images in reverse or skips the recorded images.

: Forward searches the recorded images or skips the recorded images.

•Z: Stops playback.

Front panel release button : Press these buttons to separate the front panel for HDD installation.

Indicator

• NET: Blinks when the network is connected.

• HDD: Lights when the HDD is accessed.

• ALARM: Lights when the alarm out is in progress.

• BACK UP: Lights when the data back up is in progress.

Preparation

Channel Buttons: You can input a number with channel buttons. You can also use the channel buttons for sub-function with SHIFT

button (11 to 16 buttons of 8 channel DVR are used for sub-function without SHIFT button.). You should press the OK button after input the channel number when you select the applicable channel.

• The LED in the button indicates the status as follows:

- Off: The current status is for live mode.

- Red: Recording mode.

- Blinks when an event occurs.

• Sub-functions

Button number Function Description

1 OSD Accesses or minimizes the System Control Bar (OSD).

2 PTZ Switches this unit to PTZ mode to control the connected PTZ camera.

3/7

4/8 IRIS - / IRIS + Adjust iris position.

5 INFO Displays the system information.

6 ALM.OFF

9 LOG Displays the System Log List.

10 TEXT OFF Displays or disappears the text information if the recording data includes text data.

11 SET Registers the PTZ camera’s preset position.

12 CLEAR Deletes a memorized preset position.

13 COPY Displays the export menu.

14 MARK Sets the mark point for recording search.

15 MOVE Moves the camera to the preset position.

16 TOUR Tours all registered preset positions in the camera.

FOCUS -

/ FOCUS +

Adjusts focus position.

Cancels alarm activation and returns the system to the condition before the alarm was activated.

Remote Sensor: Point the remote control here.

SHIFT button: If you use the Sub-function of the channel button, the button is activated.

ZOOM + / -: Zooms in/out on playback window.

Arrow and OK Buttons

•

wsad

• OK: Confirms menu selections.

Disc Tray: Insert a disc here.

OPEN: Opens or closes the disc tray.

LOG-IN: Displays the User Log-In dialog box or logs out.

SEARCH: Displays the search menu.

SETUP: Displays the setup menu.

VIEW: Displays the split mode menu for MAIN Monitor and SPOT Monitor.

CAM: Displays the Monitor menu to set the first camera channel.

USB Port: Connects an external USB device for backup or playback.

BACK: Exits the menu or returns to the previous screen.

REC: Starts or stops instant recording.

: Select or move between the menu options.

Rear Panel

Rear of the LRH7160D series

a b c d

e f g h i j f k l m n o

Preparation

Rear of the LRH7080D series

a b c d

e f g h i j k l m n o

VIDEO INPUT: Connect the camera’s video output to these BNC connectors.

LOOP OUT: The signal from VIDEO INPUT connector is looped out to this connector.

RELAY-OUT Terminals: Output terminals for alarm (relay) signal.

Power Cord Inlet (AC IN): Connect the power plug.

AUDIO OUT 1 / 2: Connect to an active speaker with a built-in amplifier.

AUDIO IN: Connect the audio output of an external device.

ALARM-IN Terminals: Input terminals for alarm (relay) signal.

ATM/POS: Used to connect to a ATM/POS device.

VGA: Connect a VGA monitor.

SPOT-OUT (BNC Type Connector): Connect to spot monitor or display device.

HDMI: Connect to monitor or display device with HDMI inputs. (Interface for digital audio and video)

LAN Ports: Connect the ethernet 10/100/1000 Mbps network cable for controlling this unit via a PC network.

E-SATA: Connect the external SATA device.

USB Port: Connect an optional extension USB device.

RS-485 Terminals: Connect RS-485 compatible cameras.

Preparation

Remote Control

Preparation

Button Description

POWER (1)

VIEW

CAM

ALM.OFF

OSD

SETUP

wsad

COPY

MARK

PAUSE (M)

STOP (Z)

REC (X)

c, C/aM

v, V/Md

Number Buttons

INFO

LOG

PTZ

TOUR

ZOOM + / -

FOCUS + / -

IRIS + / -

SET

CLEAR

MOVE

BACK

Turns DVR on or off.

Displays the User Log-In dialog box or logs out.

Set the appropriate DVR system ID to operate via the IR Remote Controller when using the multiple DVR. Press the ID button then press the number button within 2 seconds to select the system ID of the DVR. If you set the system ID to “0”, you can control multiple DVR at the same time.

Displays the split mode menu for MAIN Monitor and SPOT Monitor.

Displays the Monitor menu to set the first camera channel.

Cancels alarm activation and returns the system to the condition before the alarm was activated.

Accesses or minimizes the system control bar.

Displays the setup menu.

Selects or moves between the menu options.

Confirms menu selections.

Copies the recording data to an external device.

Displays the search menu.

Sets the mark point for recording search. You can set the mark point during the single or multi channel playback of recorded data.

Pauses playback.

Stops playback.

Starts or stops recording.

Searches the recorded images in reverse or skips the recorded images.

Playback or reverse playback of recorded images.

Forward searches the recorded images or skips the recorded images.

Selects the PTZ preset number, ID or channel.

Displays the system information window.

Displays the System Log List window.

Switches this unit to PTZ mode to control the connected PTZ camera.

Tours all registered preset positions in the camera.

Zooms in/out on the playback window. If you press ZOOM(+) button during viewing a live channel in full screen mode or playing back a channel in full screen mode, the digital zoom function is activated.

Adjusts the focus of a camera.

Adjusts the iris of a camera.

Registers the PTZ camera’s preset positions.

Deletes a memorized preset position.

Moves the camera to the preset position.

Exits the menu or returns to the previous screen.

3 Installation

Connections

Installation

Precautions

• Depending on the camera and other equipment there are various ways to connect the unit. Please refer to the camera manual or manuals for other devices as necessary for additional connection information.

• Be sure to switch off the camera before installation and connection.

Basic Connection Overview

Connect the coaxial-type cameras

Connect the Monitor, DVR, VCR, or others.

Connect ATM/ POS unit.

Connect the alarm (relay).

Connect power cord.

Installation

Connect audio (line input).

Connect audio amplifier.

Connect alarm sensors.

Connect PTZ cameras, DVRs or keypads (optional).

Connect the external SATA device.

Connect an external USB device for backup or playback.

Connect a mouse device.

Connect network cable for client control or IP camera input.

Connect HDMI type monitor (MAIN or SPOT).

Connect BNC type monitor (SPOT).

Connect VGA monitor.

Installation

Connecting Camera

Connect the video output of your camera to the unit, using a standard 75 Ω video coaxial cable with BNC connector. LOOF OUT connector passes the video signal from VIDEO INPUT connector to connect to other device.

Camera connection

Installation

NOTE

If the distance between the camera and DVR is too long, the noise may be generated. In this case, we recommend you to ground DVR’s power and not to ground camera’s power.

Connecting Display device

This unit can be output simultaneously from the HDMI, VGA and SPOT OUT jack. The video signal connection between the DVR and the monitor.

VGA Monitor connection

Connect the VGA jacks on the rear of the unit to the corresponding input jacks on the TV or monitor using the VGA cable.

VGA Monitor connection

Connecting the video distributor

Connect the video signal of the camera to the input connector of the video distributor using a 75 Ω video coaxial cable with BNC connector. Connect the video output of the video distributer to the VIDEO INPUT connector of DVR using a using a 75 Ω video coaxial cable with BNC connector. Connect your monitor to the video output connector of the video distributor.

Connecting the video distributor

Video distributor

Monitor Monitor

NOTE

DVR

SPOT Monitor connection

Connect the unit to the SPOT monitor using 75 Ω video coaxial cables with BNC connector.

SPOT Monitor connection

• If the cable’s length is too long, DVR’s parts may be damaged due to an external static electricity. Before connecting the video cable, touch the end of the cable to DVR’s case to avoid the risk of static buildup.

• Please check the images via a monitor after installation of the video distributor.

HDMI Monitor connection

Connect the unit to the HDMI monitor using a HDMI cable (Type A, High Speed HDMITM Cable).

HDMI Monitor connection

MAIN SPOT

Connecting Audio device

Connect the AUDIO OUT jacks on the unit to the mono audio in jacks on your audio device.

Microphone and Speaker connection

Installation

USB Memory device

Insert the memory device into the USB port. The system automatically recognizes the device. The system software can be easily upgraded using a USB memory device.

USB External device

Connect the external device to the USB port. (Example: External HDD or other external storage.)

Mouse

Connect the USB mouse to operate the functions of the DVR.

Installation

Connecting USB device

USB device connection

Connecting E-SATA device

You can use E-SATA storage for data back-up or recording.

E-SATA device connection

Installation

Connecting ATM/POS

Connect the ATM/POS unit to the ATM/POS port.

ATM/POS device connection

Installation

Connecting Network

You can control and monitor the system via network. With the remote control (monitoring), you can change the system configuration or monitor the image via network. After the installation, check the network settings for the remote control and monitoring work.

Network connection

Broadband

Router

Broadband

Service

NOTE

• The following device has been tested and compatibility is ensured. When you use the multiple ATM/POS device, use the recommended device.

- AVE Products

› VSI-PRO: Video serial interface

› Regcom: RS-485 networker

› Hydra: RS-485 to RS-232 converter

• The installation and connection work should be done by qualified service personnel or system installers and should be conformed to all local codes.

LAN connection

Connect the LAN port to an available 10/100/1000 base-T port with a straight ethernet cable (not supplied). The NET indicator on the front panel will be lit.

IP Camera connection

Connect the IP camera. After the installation, check the IP camera settings on the setup menu.

Automatic network configuration

The DVR can automatically obtain and configure the network interface via DHCP.

Manually configure network

The DVR may be manually configured by assigning an IP address, subnet mask, gateway and DNS.

NOTE

This unit can be supported IPv4 and IPv6 network.

Installation

Connecting RS-485 device

This DVR has two data terminals. Use this port to connect PTZ cameras, DVRs or keypads (optional).

RS-485 Terminal Description

D - (DATA -) Data Transmission/Reception

D + (DATA +) Data Transmission/Reception

GND Shield

Connecting the PTZ device

Connecting the PTZ serial communication lines to the RS-485 terminal.

PTZ device connection

Connecting LKD1000 controller

Connect the LKD1000 controller to control the DVR. (Refer to the manuals of the LKD1000 controller for more details.) The LKD1000 controller has to be connected to the 2 (DATA 2) port as shown illustration. If you connect the LKD1000 controller to the 1 (DATA 1) port, the LKD1000 controller will not be activated.

LKD1000 controller connection

Installation

PTZ units

(RS-485 type)

PTZ units

(RS-485 type)

NOTE

• When connecting lines, connect the “D -” of the DVR to “RX -” of the PTZ unit and “D +” of the DVR to “RX +” of the PTZ unit correctly.

• Recommended initial data are 9600 Baud Rate, 8 Data bits, 1 Stop bit and No parity.

• When connecting PTZ cameras to DVRs it is necessary to set the setup menu for this unit according to the RS-485 settings of the camera and DVRs.

TX+TX-

LKD1000 Controller

NOTE

Do not connect a PTZ camera and LKD1000 controller to the D1 or D2 port at the same time. It may cause a malfunction.

Connecting Alarm Input and Alarm Output

Alarm terminals are used to connect the alarm devices such as sensors, door switches, etc.

Alarm Input

You can connect up to 16 alarm sensors (LRH7080D: 8 alarm sensors). Each alarm sensor should be connected with G (GND). The signal state is adjustable to N/O (Normal Open) or N/C (Normal Close) through the setup menu.

Installation

Sensor input connection

Alarm Output

Connect the alarm device to the alarm output. Alarm signal outputs when an event occur.

Alarm output connection

Alarm device

Alarm sensor Alarm sensor

Terminal No. Description

1 Sensor Input 1

2 Sensor Input 2

3 Sensor Input 3

4 Sensor Input 4

G Ground

5 Sensor Input 5

6 Sensor Input 6

7 Sensor Input 7

8 Sensor Input 8

G Ground

9 Sensor Input 9

10 Sensor Input 10

11 Sensor Input 11

12 Sensor Input 12

G Ground

13 Sensor Input 13

14 Sensor Input 14

15 Sensor Input 15

16 Sensor Input 16

G Ground

Terminal No. Description

G Ground

1 Alarm Output 1

2 Alarm Output 2

3 Alarm Output 3

4 Alarm Output 4

NOTE

The internal switching relays are rated for 0.3 A at 125 V AC or 1 A at 30 V DC. If the electric current is higher than that the unit can be damaged.

Installation

HDD INSTALLATION

Note for Hard Disk Drive

The internal hard disk drive (HDD) is a fragile piece of equipment. Please follow the guidelines below when using the DVR to protect against possible HDD failure. We recommend that you back up your important recordings onto an external backup device in order to prevent accidental loss.

Make sure that the power is turned OFF when attaching or removing the HDD.

• Do not move the DVR while the power is on.

• Do not use the DVR in excessively hot or humid places, or in

places that may be subject to sudden changes in temperature. Sudden changes in temperature can cause condensation to form inside the DVR. This can be a cause of HDD failure.

• While the DVR is switched on, do not unplug from the wall socket or switch the electricity off from the breaker switch.

• If there’s a power failure while the DVR is on, some data on the HDD may be lost.

• Do not drop the HDD. Also do not put the metallic object such as coins or screwdrivers into the HDD tray.

• When a power failure occurs during recording, avoid adding, replacing or transporting the HDD as the recorded data may be erased. In this case, turn the power back on to boot up the unit normally with the HDD that was being used at the time of the power failure attached. Then add, replace, or transport the HDD.

• The HDD is very delicate. Handle the HDD with care and follow the precautions below because even a tiny shock may damage the internal components of the HDD.

- Do not place the HDD on the desk or table directly. Put a thick cushion under the HDD because even a small shock may damage the internal components of the HDD.

- Do not use an electric screwdriver. Vibrations and shocks caused by an electric screwdriver may damage the internal components of the HDD.

- When replacing the HDD, do not knock the HDD with other components such as another HDD and the HDD tray.

- Do not knock the HDD with tools such as a driver when replacing the HDD.

• Protect the hard disk drives from static electricity.

6. When you turn the power of the unit on, the new HDD is detected and formatted automatically.

CAUTION

You should install the hard disk drive from 1 to 6 in order.

Replacing the Hard Disk Drive

Turn the power of the unit off and detach the power plug from the outlet.

1. Disassemble the front panel by pressing the release button on the front panel.

2. Loosen the screws and detach the hard disk mounting brackets from the units.

3. Replace the new HDD.

4. Close the front panel by hanging the bottom hook after push the Front panel release button.

5. After replacing the hard disk drive, insert the power plug into the outlet and turn the power of the unit on. The new HDD is detected and formatted.

automatically.

NOTE

Do not use an electric screwdriver to fix them.

Recommended HDD

For the latest recommended HDD list, please visit http://www.lgecommercial.com

NOTE

If you do not use the recommended HDD, the system may not be operated normally.

Installation

Installing the Hard Disk Drive

You can install up to 6 HDDs.

Improper installation or setup may disturb HDD recognition or normal product operation. So you should consult with an expert from the store where the product was purchased.

1. Disassemble the front panel by pressing the release button on the front panel.

2. Loosen the screws and detach the hard disk mounting brackets from the units.

3. Attach the HDD onto the hard disk mounting brackets with four screws.

4. Attach the hard disk mounting brackets with the screws.

5. Close the front panel by hanging the bottom hook after push the Front panel release button.

Installation

System Operation

1. Turn on the unit. System booting will commence. The LG logo image will be displayed on the main monitor during the system booting.

2. When the booting is completed the live window will be

displayed. Click the icon on the system control bar or press

the LOGIN button on the remote control to display the log-in window.

3. Select a user name by using the mouse or arrow and the OK button on the remote control or front panel. For the first time,

Installation

you can select the ADMINISTRATOR user name only. You can register a new user with various access rights using the user setup menu.

4. Enter the password by using the virtual keyboard. (Note that the default administrator password is “000000”.)

5. Click the [OK] icon. You can see the live screen and operate the system.

NOTE

• This DVR is based on a VGA monitor using OSD. We recommend you to using the VGA monitor with this unit. If you use a composite monitor, the OSD quality may be low to read it.

• If the DVR is turned off accidently and then turned on again, the DVR may take a long time to be rebooted.

System Shutdown

General Explanation of the Live Screen on the Main Monitor

Main Monitor Screen

a b cde f g h

Channel Number

Displays the channel number.

Channel Name

Displays the edited channel name.

Selected Channel

Displays the selected channel with red box.

Channel FPS

Displays the channel FPS value.

Camera Status Icon

Displays the PTZ camera status.

1. First, you must stop playback and exit the setup menu. In playback, press STOP.

2. Press and hold 1 (POWER) button until the beep sounds and the logout window will be displayed.

3. Enter the password by using the virtual keyboard.

4. Click the [OK] icon. The system will shutdown.

Displays the input audio status.

Displays the IP camera status.

Gold “C” indicates continuous recording.

Gold “I” indicates Instant recording.

Red “S” indicates sensor triggered recording.

Green “M” indicates motion detection recording.

Gray “N” indicates the channel is not being recorded.

Violet “T” indicates text event recording.

Quick Buttons

The Quick Buttons will appear when the mouse is moved to the camera's live screen. You can use the following functions by clicking it for the selected channel.

You can use the playback function.

You can use the digital zoom function.

Installation

You can control the PTZ Camera. (optional)

You can use the video adjustment (Brightness, Contrast, Color) function. (Analog Channel Only)

Live Screen

Displays the current surveillance live screen.

System Control Bar

Displays the CPU usage and Data traffic level of IP cameras.

Displays date and time.

( )

Search: Displays the search menu.

Alarm Off: Turns the alarm off.

Camera: Displays the Monitor menu to set the first camera channel.

Split mode: Displays the menu for selecting the screen division.

Video Export: Displays the export menu.

System Log: Displays the system log list window.

System Information: Displays the system information window.

Moving the Channel's Position

You can change the camera channel's position in a split screen of the Main Monitor.

1. Select a desired channel by clicking the left button of the mouse.

2. Drag and drop it to a desired location and the channel's position will be changed.

Installation

Selecting the Main Monitor screen mode

You can select the live screen mode to display a full, 4-split, 6-split, 8-split, 9-split, 16-split, 17-split or 25-split screens on the main monitor.

1. Press VIEW or click icon in the system control bar.

2. Select [Main Monitor].

3. Select a screen mode.

Setup: Displays the setup menu.

Minimizes the System Control Bar.

NOTE

• To display / minimize the system control bar

To display or minimize System Control Bar, press OSD after pressing the SHIFT button on the front panel or click in the System Control Bar.

• You can also use the system control's options by clicking the right button of the mouse on the Main Monitor screen.

• When data signal color of IP camera is changed yellow or red, reduce bit rate, frame rate, resolution and connections of IP camera.

• While the main monitor is performing the sequence mode, the

mark is displayed on the system control bar.

Screen split mode

Sequence mode

• Full Screen Mode: You can view the live window in full screen mode.

• 4, 9, 16, 25, 1+5, 1+7 and 1+16 Split Mode: Displays selected split screens on the main monitor.

• Sequence: You can view all the channels in sequence. You cannot use sequence mode with the 25 split (LRH7080D series: 16 split).

4. Select [OK] and press OK to confirm your selection.

NOTE

To display the screen you want to watch in full screen mode, double click the desired channel.

Installation

Selecting the Spot Monitor screen mode

You can select the live screen mode to full, 4-split, 9-split, 16-split or 25-split screens on the spot monitor.

1. Press VIEW or click the icon in the system control bar.

2. Select [Spot Monitor].

3. Select a screen mode.

Installation

Screen split mode

Sequence mode

• Full Screen Mode: You can view the live window in full screen mode.

• 4, 9, 16 and 25 Split Mode: Displays selected split screens on the spot monitor.

• Sequence: You can view all the channels in sequence. You cannot use sequence mode with the 25 split (LRH7080D series: 16 split).

4. Select [OK] and press OK to confirm your selection.

NOTE

The image of IP Camera’s on Spot Channel may not be operated smoothly during playback.

Grouping channel

You can group channels you want.

1. Press CAM or click the icon in the system control bar.

2. Select [Main Monitor] or [Spot Monitor] on the menu.

3. Select a camera number for including group.

- [Restore to Default] : Reset channels to ascending sort and change the [Split Mode] to 25 split. (LRH7080D series: 16 split)

4. Select group number on the drop-down list.

5. Click [Load] or [Save] button to configure your group.

6. Select [OK] and press OK to confirm your selection.

NOTE

The [Split Mode] changes according to a number of selected cameras.

PTZ Camera Control

You can control the cameras connected via the data port of RS-485 terminal or Network. You must set the configuration between the PTZ camera and the DVR.

1. Select the PTZ camera channel on the main monitor you want to control.

2. Press PTZ or click the icon that appears when the mouse is moved to PTZ camera's screen. Virtual PTZ remote control is displayed on the main monitor.

3. Use each item to control the PTZ camera.

Button Function

Displays the PTZ control guide.

Displays the setup menu of the PTZ camera.

Minimizes PTZ virtual remote control.

Removes the PTZ virtual remote control.

Use to pan/tilt the camera.

You can select the Pan/Tilt/Zoom speed.

You can adjust the camera zoom.

+ 49 hidden pages