English Version2
Versión en Español
Version Fran aiseç
Warranty (U.S.A)3
Warranty (CANADA)4
Safety Instructions5 - 6
Grounding Requirements7
Parts and Features7
Refrigerator Installation8 - 11
Unpacking Your Refrigerator8
Installation8
Base Grille8
Removing, Reversing and Replacing
Your Refrigerator Doors9 -10
Door Closing and Alignment11
Using Your Refrigerator12 -19
Ensuring Proper Air Circulation12
Multi Flow12
Setting the Controls12
Adjusting Control Settings13
Food Storage Guide13
Storing Frozen Food14
Refrigerator Shelves14
Snack Pan15
Crisper Humidity Control15
27
49
Optibin Crispers15
Crisper Cover with Lattice on inner Surface16
Door Racks16
Design-A-Door16
Dairy Bin17
Freezer Wire Door Racks17
Ice Bin17
Wire Durabase17
Wire Basket17
Wire Basket Divider17
Drawer Tray18
Triple Twist Ice Tray
Care and Cleaning19 -20
General Cleaning Tips19
Outside19
Inside Walls19
Door Liner and Gaskets19
Plastic Parts19
Condenser Coils19
Light Bulb Replacement19 - 20
Power Interruptions20
When you go on vacation20
Troubleshooting Guide21 - 24
18
2
Page 3
visit our web site/http://www.lgservice.com
LG Electronics
LIMITED WARRANTY
United States of America
LG Electronics will repair or at its option replace, without charge, your product which proves to be defective
in material or workmanship under normal use during the warranty period listed below from the date of
original purchase.
This warranty is good only to the original purchaser of the product during the warranty period as long as it
is in the U.S. including Alaska, Hawaii, and U.S. Territories.
LG Refrigerator / Freezer Warranty Period
ProductPartsLabor
Refrigerator/Freezer1 year1 year [In-Home Service (Except Model Gr051)]
Sealed System7 years1 year [In-Home Service (Except Model Gr051)]
(Compressor, Condenser, Evaporator)
No other express warranty is applicable to this product. THE DURATION OF ANY IMPLIED WARRANTIES.
INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY, IS LIMITED TO THE DURATION OF
THE EXPRESS WARRANTY HEREIN. LG ELECTRONICS SHALL NOT BE LIABLE FOR THE LOSS OF
USE OF THE PRODUCT, INCONVIENCE, LOSS OR ANY OTHER DAMAGES, DIRECT OR
CONSEQUENTIAL, ARISING OUT OF THE USE OF OR INABILITYTO USE, THIS PRODUCT OR FOR
ANY BREACH OF ANY EXPRESS OR IMPLIED WARRANTY, INCLUDING THE IMPLIED WARRANTY
OF MERCHANTABILITYAPPLICABLE TO THIS PRODUCT.
Some States do not allow the exclusion or limitation of incidental or consequential damages or limitations on how
long an implied warranty lasts; so these limitations or exclusions may not apply to you. This warranty gives you
specific legal rights and you may also have other rights which vary from state to state.
THE ABOVE WARRANTY DOES NOT APPLY TO:
1.Service trips to your home to deliver and pickup, install, instruct, or replace house fuses or correct house wiring or
plumbing, or correction of unauthorized repairs.
2.Damage to the product caused by accident, pests, fire, floods, or acts of God.
3.Repairs when your LG product is used in other than normal, single-family household use.
4.Damage resulting from accident, alteration, misuse, abuse, or improper installation.
Therefore, these costs are paid by the consumer.
If the product is installed outside the normal service area, any cost of transportation involved in the repair of the producto, r the
replacement of defective parts, shall be borne by the owner.
CUSTOMER ASSISTANCE NUMBERS:
To obtain Warranty Coverage:Retain your Bill of Sale to prove date of purchase.
A Copy of your Sales Receipt must be submitted at the time
warranty service is provided.
To obtain Product or CustomerCall 1-800-243-0000 (Mon.~ Fri. 7AM ~ 8PM CT)
Service Assistance:(Sat. 8AM ~ 5PM CT)
Press the appropriate menu option, and have your product
type (Refrigerator), model number, serial number, and
ZIP/Postal Code ready.
To obtain the nearestCall 1-800-243-0000 (24 hrs a day, 7 days per week)
Authorized Service Center:Press the appropriate option, and have your product type
(Refrigerator), model number, serial number, and ZIP/Postal
Code ready.
3
Page 4
LIMITED WARRANTY (CANADA)
LG REFRIGERATOR
LG Electronics will repair or at its option replace, without charge, your product which proves to be defective in
material or workmanship under normal use, during the warranty period listed below from the date of original
purchase. This warranty is good only to the original purchaser of the product during the warranty period as
long as it is in any Canadian Province.
WARRANTY PERIOD
LABOR
SERIAL NU MBER :
SEALED SYSTEM : 5 Years (Compressor, condenser, and evaporator)
HOW SERVICE IS HANDLED : Call 1-888-542-2623 (1-888-LG-CANADA) and choose the appropriate
prompt. Please have product type (refrigerator) and ZIP Code ready.
See our website at http://www.lg.ca
This warranty provides in-home service.
No other express warranty is applicable to this product. THE DURATION OF ANY IMPLIED WARRANTIES,
INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY, IS LIMITED TO THE
DURATION OF THE EXPRESS WARRANTY HEREIN. LG ELECTRONICS USA, INC. SHALLNOT
BE LIABLE FOR THE LOSS OF THE USE OF THE PRODUCT, INCONVIENCE, LOSS OR ANY
OTHER DAMAGES, DIRECT OR CONSEQUENTIAL, ARISING OUT OF THE USE OF, OR
INABILITY TO USE, THIS PRODUCT OR FOR ANY BREACH OF ANY EXPRESS OR IMPLIED
WARRANTY, INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY APPLICABLE TO
THIS PRODUCT.
Some provinces do not allow the exclusion or limitation of incidental or consequential damages or limitations on
how long an implied warranty lasts; so these limitations or exclusions may not apply to you. This warranty gives
you specific legal rights and you may also have other rights which vary from province to province.
: 2 Years PARTS : 2 Years
THE ABOVE WARRANTY DOES NOT APPLY TO:
1.Service trips to your home to deliver and pickup, install, instruct, or replace house fuses or correct wiring, plumbing,
or correction of unauthorized repairs.
2.Damage to the product caused by accident, vermin, fire, flood, alteration, misu es , abuse, improper installation, or acts
of God.
3.Commercial use or use for other than the intended purpose.
Therefore, these costs are the responsibility of the consumer.
CUSTOMER ASSISTANCE NUMBERS:
To Prove Warranty Coverage:
To Obtain Product, Customer, or
Service Assistanceby phone:
or by Internet:
To Obtain Nearest Authorized
Service Center, Parts Distributor,
or Salesne
Retain your Sales Receipt to prove date of purchase.
A copy of your Sales Receipt must be submitted at the time
warranty service is provided.
Call 1-888-542-2623 (1-888-LG-CANADA) and choose the
appropriate prompt.
http://www.lg.ca
Call 1-888-542-2623 (1-888-LG-CANADA) and choose the
appropriate prompt. Please have your product type
(refrigerator) and ZIP Code ready.
http://www.lg.ca
4
Page 5
IMPORTANT SAFETY INSTRUCTIONS
SAFETY MESSAGES
This guide contains many important safety messages. Always read and obey all safety messages.
This is the safety alert symbol. It alerts you to safety messages that inform you
of hazards that can kill or hurt you or others, or cause damage to the product.
All safety messages will be preceded by the safety alert symbol and the hazard
signal word DANGER, WARNING, CAUTION. These words mean:
DANGER
You will be killed or seriously injured if you don’t follow instructions
WARNING
You can be killed or seriously injured if you don’t follow instructions.
CAUTION
All safety messages will identify the hazard, tell you how to reduce the chance of injury and tell you what can happen if
the instructions are not followed.
Indicates an imminently hazardous situation which, if not avoided,
may result in minor or moderate injury, or product damage only.
WARNING
To reduce the risk of fire, electric shock, or injury
to persons when using your product, basic safety
precautions should be followed, including the following:
NEVER unplug your refrigerator by pulling on the power cord.
Always grip the plug firmly and pull it straight out from the
outlet.
Repair or replace immediately all electric service cords that
have become frayed or otherwise damaged. Do not use a cord
that shows cracks or abrasion damage along its length or at
either the plug or connector end.
When moving your refrigerator away from the wall,
be careful not to roll over or damage the power cord.
DO NOTsto re or use gasoline or other flammable vapors and
liquids in the vicinity of this or any other appliance.
DO NOTallow children to climb, stand or hang on the
refrigerator doors or shelves in the refrigerator. They could
damage the refrigerator and seriously injure themselves.
Keep fingers out of “pinch point” areas; clearances between
the doors and cabinet are necessarily small. Be careful
when you open the doors when children are in the area.
Unplug your refrigerator before cleaning or making any repairs.
NOTE: We strongly recommend that any servicing be
performed by a qualified individual.
Before replacing a burned-out light bulb, unplug the
refrigerator or turn off power at the circuit breaker or fuse box
in order to avoid contact with a live wire filament. (A burnedout light bulb may break when being replaced.)
either or both controls to the OFF position does not remove
power to the light circuit.
NOTE: Setting
For personal safety, this appliance must be properly grounded.
Have the wall outlet and the circuit checked by a qualified
electrician to make sure the outlet is properly grounded.
Read all instructions before using this appliance.
Use this appliance only for its intended purpose as described
in this use and care guide.
After your refrigerator is in operation, do not touch the cold
surfaces in the freezer compartment when hands are damp or
wet. Skin may adhere to the extremely cold surfaces.
In refrigerators with automatic icemakers, avoid contact with
the moving parts of the ejector mechanism, or with the heating
element that releases the cubes. DO NOT place fingers or
hands on the automatic icemaking mechanism while the
refrigerator is plugged in.
DO NOTrefre eze frozen foods which have thawed completely.
The United States Department of Agriculture in Home and
Garden Bulletin No. 69 says:
“...You may safely refreeze frozen foods that have thawed if
they still contain ice crystals or if they are still cold below
40°F (4°C).”
“...Thawed ground meats, poultry, or fish that have any off-odor
or off-color should not be refrozen and should not be eaten.
Thawed ice cream should be discarded. If the odor or color of
any food is poor or questionable, get rid of it. The food may be
dangerous to eat.”
“Even partial thawing and refreezing reduces the eating quality
of foods, particularly fruits, vegetables and prepared foods.
The eating quality of red meats is affected less than that of
many other foods. Use refrozen foods as soon as possible to
save as much of their quality as you can.”
SAVE THESE INSTRUCTIONS
5
Page 6
DANGER: RISK OF CHILD ENTRAPMENT
Child entrapment and suffocation are not problems of
the past. Junked or abandoned refrigerators are still
dangerous... even if they will sit for “just a few days”. If
you are getting rid of your old refrigerator, please follow
the instructions at right to help prevent accidents.
BEFORE YOU THROW AWAY
YOUR OLD REFRIGERATOR
OR FREEZER
Take off the doors.
Leave the shelves in place so that
children may not easily climb inside.
CFC DISPOSAL
Your old refrigerator may have a cooling system that usedIf you are throwing away your old refrigerator, make sure
CFCs (chlorofluorocarbons). CFCs are believed to harmthe CFC refrigerant is removed for proper disposal by a
stratospheric ozone. qualified servicer. If you intentionally release this CFC
refrigerant, you can be subject to fines and imprisonment
under provisions of environmental legislation.
GROUNDING REQUIREMENTS
IMPORTANT:
Please read carefully.
TO CONNECT ELECTRICITY
WARNING
Electrical Shock Hazard
FOR PERSONAL SAFETY, this appliance must be
properly grounded. Have the wall outlet and the
circuit checked by a qualified electrician to make sure
the outlet is properly grounded.
3-prong
grounding type
wall receptacle
3-prong
grounding
plug
separate circuit serving only this appliance be provided.
Use a receptacle which cannot be turned off with a switch
or pull chain. Do not use an extension cord.
Where a standard two-prong wall outlet is encountered,
it is your personal responsibility and obligation to have it
replaced with a properly grounded three-prong wall outlet.
Do not, under any circumstances, cut or remove the
third (ground) prong from the power cord.
NOTE: Before performing any type of installation,
cleaning, or removing a light bulb, turn the control
(Thermostat, Refrigerator Control or Freezer Control,
depending on the model) to OFF and then disconnect the
refrigerator from the electrical source. When you are
finished, reconnect the refrigerator to the electrical source
and reset the control (Thermostat, Refrigerator Control or
Freezer Control, depending on the model) to the desired
setting.
USE OF EXTENSION CORDS
Ensure proper
ground exists
before use.
RECOMMENDED GROUNDING METHOD
The refrigerator should always be plugged into its own
individual properly grounded electrical outlet rated for
115 Volts, 60 Hz, AC only, and fused at 15 or 20 amperes.
This provides the best performance and also prevents
overloading house wiring circuits which could cause a fire
hazard from overheated wires. It is recommended that a
Because of potential safety hazards under certain
conditions, we strongly recommend against the use of
an extension cord. However, if you still elect to use
an extension cord, it is absolutely necessary that it be
a UL-listed (in the United States), 3-wire grounding type
appliance extension cord having a grounding type plug
and outlet, and that the electrical rating of the cord be 15
amperes (minimum) and 120 volts.
Use of an extension cord will increase the clearance
needed for the back of the refrigerator.
6
Page 7
PARTS AND FEATURES
Use this section to become more familiar with the parts and features. Page references are included for your
convenience.
NOTE: This guide covers several different models.The refrigerator you have purchased may have some
or all of the items listed below. The locations of the features shown below may not match your model.
7
Page 8
REFRIGERATOR INSTALLATION
INSTALLATION
WARNING
Excessive Weight Hazard
Use two or more people to move and install
refrigerator.
Failure to do so can result in back or other injury.
UNPACKING YOUR REFRIGERATOR
Remove tape and any temporary labels from your
refrigerator before using. Do not remove any warningtype labels, the model and serial number label, or the
TechSheet that is attached to back wall of the refrigerator.
To remove any remaining tape or glue, rub the area
briskly with your thumb. Tape or glue residue can also be
easily removed by rubbing a small amount of liquid dish
soap over the adhesive with your fingers. Wipe with warm
water and dry.
Do not use sharp instruments, rubbing alcohol, flammable
fluids or abrasive cleaners to remove tape or glue. These
products can damage the surface of your refrigerator. For
more information, see the Important Safety Instructions
section.
Refrigerator shelves are installed in the shipping position.
Please reinstall shelves according to your individual
storage needs.
When Moving Your Refrigerator:
Your refrigerator is heavy. When moving the
refrigerator for cleaning or service, be sure to protect
the floor. Always pull the refrigerator straight out when
moving it. Do not wiggle or walk the refrigerator when
trying to move it, as floor damage could occur.
1. Avoid placing the unit near heat sources, direct sunlight,
or moisture.
2. To avoid vibration, the unit must be level. If required,
adjust the leveling screws to compensate for
unevenness of the floor. The front should be slightly
higher than the rear to aid in door closing. Leveling
screws can be turned easily by tipping the cabinet
slightly. Turn the leveling screws clockwise ( ) to
raise the unit, counterclockwise ( ) to lower it.
3. Install this appliance in an area where the temperature
is between 55°F (13°C) and 110°F (43°C.) If the
temperature around the appliance is too low or high,
cooling ability may be adversely affected.
NEXT
1. Clean your refrigerator thoroughly and wipe off all dust
accumulated during shipping.
2. Install accessories such as ice cube bin, drawers,
shelves, etc., in their proper places. They are packed
together to prevent possible damage during shipment.
3. Let your refrigerator run for 2 or 3 hours before putting
food in it. Check the flow of cold air in the freezer
compartment to ensure proper cooling. Your refrigerator
is now ready for use.
CAUTION:
Be careful when you work with hinge, base grille,
stopper etc. You may be injured.
Do not put hands or metal sticks into air vents, base
grille or bottom of refrigerator. You may be injured or
receive an electrical shock.
BASE GRILLE
WARNING
Explosion Hazard
Keep flammable materials and vapors, such as
gasoline, away from refrigerator.
Failure to do so can result in death, explosion or fire.
To remove the base grille:
1. Grasp the grille with both hands.
2. Pull the grille toward yourself.
To install the base grille:
1. Place clips in openings in the metal panel.
2. Push the grille toward the refrigerator until it snaps
into place.
8
Page 9
REFRIGERATOR INSTALLATION
REMOVING, REVERSING AND REPLACING
REFRIGERATOR DOORS
IMPORTANT: Before you begin, turn the refrigerator OFF
and unplug it. Remove food and any adjustable door or
utility bins from doors.
HOW TO REVERSE DOOR OPENING DIRECTION
(when converting from the left-opening type to rightopening type)
1. Removing Refrigerator Door
Remove the top hinge cover (1).
Remove the 3 screws and lift of f the top hinge (2).
Lift the Refrigerator door (3) slightly and remove it.
Pry off the cover (4) using a slotted screwdriver and
attach it on the right.
Loosen the screw (5), remove the stoppers (6) and
attach them on the left (on the opposite side).
Loosen the pin (8) and remove it.
Lift off the washer (9).
Pry off the cover (7) using a slotted screwdriver and
attach it on the right.
2. Removing Freezer Door
Lift the door (10) slightly and remove it.
Loosen the 2 screws (11), the 2 screws (12), and lift
off the middle hinge (13).
Take off the base grille (14).
Remove the cap (15) and attach it on the right.
Loosen the 2 screws (16), remove the bottom hinge
(17), and attach on the right.
Loosen the 2 screws (18), remove the bottom hinge
(19), and attach on the left.
Loosen the 2 screws (20) and attach the stopper (21)
on the left side of the base.
3. Removing Refrigerator Handle
Remove the cap (1) and the 2 caps (2) using a
slotted screwdriver save the caps.
Pull the upper cover (3) upward and take it of f.
Pull the lower cover (4) downward and take it of f.
Loosen the 2 screws (5), take of f the handle (6), and
install it on the right.
Attach the upper cover (3) by pushing it down.
Attach the lower cover (4) by pushing it up.
Attach the removed the cap (1) and the 2 caps on the
left.
9
Page 10
4. Removing Freezer Handle
Remove the cap (1) and the 2 caps (2) using a slotted
screwdriver.
Pull the cover (3) upward and take it of f.
Loosen the 2 screws (4), take of f the handle (5), and
install it on the right.
Attach the cover (3) by pushing it down.
Attach the caps you removed earlier [figures (1) and
(2)].
5. Installing Freezer Door
Install the base grille (1).
Install the door (3) onto the bottom hinge pin.
Install the middle hinge (4) on the opposite side with the
screw (5) and the screws (9).
6. Installing Refrigerator Door
Place the washer (6) on the middle hinge pin (7).
Install the door (8) so that it fits onto the middle hinge
pin (7).
Install the top hinge (10) with serews.
Reinstall top hinge cover (11).
7. After Completing the Job
Make sure that the four corners of the door gasket are
not folded over. To ensure a good seal, apply a small
amount of silicon grease on the gasket.
10
Page 11
REFRIGERATOR INSTALLATION
DOOR CLOSING AND ALIGNMENT
Door Closing
Your refrigerator has two front leveling screws - one on
the right and one on the left. If your refrigerator seems
unsteady or you want the doors to close easier, adjust the
refrigerator’s tilt using the instructions below:
1. Plug the refrigerator power cord into a 3-prong
grounded outlet. Move the refrigerator into its final
position.
2. Use a screwdriver to adjust the leveling screws. Turn
the leveling screw clockwise to raise that side of the
refrigerator or counterclockwise to lower it. It may take
several turns of the leveling screw to adjust the tilt of
the refrigerator.
NOTE: Having someone push against the top of the
refrigerator takes some weight off the leveling screws.
This makes it easier to adjust the screws.
Door Alignment
If the space between your doors is uneven, follow the
instructions below to align the doors:
1. Pry off the top hinge cover.
2. Loosen the top hinge screws using a 10 mm socket
or wrench.
3. Have someone hold the door in place or put a
spacer between the doors while you tighten the
top hinge screws.
4. Replace the top hinge cover.
Open both doors again and check to make sure that
3.
they close easily. If not, tilt the refrigerator slightly more
to the rear by turning both leveling screws clockwise. It
may take several more turns, and you should turn both
leveling screws the same amount.
4. Check, using a level.
5. Replace the base grille.
11
Page 12
USING YOUR REFRIGERATOR
ENSURING PROPER AIR CIRCULATION
In order to ensure proper temperatures, air must flow
between the refrigerator and freezer sections. As shown
in the illustration below, cool air enters through the bottom
of the freezer section and moves up. Most of the air then
flows through the freezer section vents and recirculates
under the freezer floor. The rest of the air enters the
refrigerator section through the top vent.
MULTI FLOW
The cooling fan operates more powerful and effective
than in normal operation. This is specially noticeable
when new food is placed in the refrigerator compartment.
If water or foreign substances enter the cool air vent
while cleaning, efficiency will be lowered. In addition, if
gasket is damaged, efficiency may be lowered because
of escaping cool air.
SETTING THE CONTROLS
Your refrigerator has two controls that let you regulate
the temperature in the freezer and refrigerator
compartments.
Initially set the REFRIGERATOR CONTROL at 37°F
(3°C) and the FREEZER CONTROL at 0°F (Leave it at this setting for 24 hours (one day) to
stabilize. Then adjust the compartment temperature
as desired.
18°
C).
Better / Good model
Refrigerator control: Position 1 to 7
(32°F to 47°F or 0°C to 8°C)
The lower the number setting, the colder the refrigerator
compartment will become.
Freezer control: Position 1 to 7
(-6°F to 8°F to - 21°C to - 13°C)
When the setting is at a lower number , the freezer
compartment becomes colder. But the refrigerator
compartment becomes warmer because less cold air
flows into the refrigerator.
Do not block any of these vents with food packages. If
the vents are blocked, airflow will be interrupted and
temperature and moisture problems may occur.
IMPORTANT: Because air circulates between both
sections, any odors formed in one section will transfer to
the other. You must thoroughly clean both sections to
eliminate odors. To prevent odor transfer and drying out of
food, wrap or cover foods tightly. (See the
Guide section for details.)
Food Storage
Express Freezing
Press the Express Freezing key and the LED will turn
on. This function will remain activated for 24 hours and
intensify the cooling speed of freezer and increase the
amount of ice.
12
Page 13
USING YOUR REFRIGERATOR
ADJUSTING CONTROL SETTINGS
Give the refrigerator time to cool down completely before
adding food. It is best to wait 24 hours before you put
food into the refrigerator. The mid-settings indicated in the
previous section should be correct for normal household
refrigerator usage. The controls are set correctly when
milk or juice is as cold as you like and when ice cream
is firm.
The refrigerator control functions as the thermostat for the
entire appliance (refrigerator and freezer sections.) The
higher the number setting, the longer the compressor will
run to keep the temperature colder. The freezer control
adjusts the cold air flow from the freezer to the
refrigerator. Setting the freezer control to a lower
temperature keeps more cold air in the Freezer
compartment to make it colder.
If you need to adjust temperatures in the refrigerator or
freezer, start by adjusting the refrigerator first. Wait 24
hours after the refrigerator adjustment to check the
freezer temperature. If it is too warm or too cold, then
adjust the freezer control as well.
Use the settings listed in the chart below as a guide.
Always remember to wait at least 24 hours between
adjustments.
Door opened oftencontrol to next
Large amount of food addedhigher number,
Room temperature very warm wait 24 hours,
FREEZER section too warm/Turn FREEZER
ice not made fast enoughcontrol to next
Door opened oftenhigher number,
Large amount of food addedwait 24 hours,
Very cold room temperature Then re-check
(can’t cycle often enough)
Heavy ice usage
Air vents blocked by itemsMove items out of
REFRIGERATOR section tooTurn
coldREFRIGERATOR
Controls not set correctly forcontrol to next
your conditionslower number,
FREEZER section too coldTurn FREEZER
Controls not set correctly forcontrol to next
your conditions lower number,
then re-check
airstream
wait 24 hours,
then re-check
wait 24 hours,
then re-check
FOOD STORAGE GUIDE
Storing Fresh Food
Wrap or store food in the refrigerator in airtight and
moisture-proof material unless otherwise noted. This
prevents food odor and taste transfer throughout the
refrigerator. For dated products, check date code to
ensure freshness.
Butter or margarine
Keep opened butter in a covered dish or closed
compartment. When storing an extra supply, wrap
in freezer packaging and freeze.
Cheese
Store in the original wrapping until you are ready to
use it. Once opened, rewrap tightly in plastic wrap or
aluminum foil.
Milk
Wipe milk cartons. For best storage, place milk on interior
shelf, not on door shelf.
Eggs
Store in original carton on interior shelf, not on door shelf.
Fruit
Wash, let dry, and store in refrigerator in plastic bags or in
the crisper. Do not wash or hull berries until you are ready
to use them. Sort and keep berries in their original
container in a crisper, or store in a loosely closed paper
bag on a refrigerator shelf.
Leafy vegetables
Remove store wrapping and trim or tear off bruised and
discolored areas. Wash in cold water and drain. Place in a
plastic bag or plastic container and store in the crisper.
Vegetables with skins (carrots, peppers)
Place in plastic bags or plastic container and store
in crisper.
Fish
Use fresh fish and shellfish the same day purchased.
Snack Pan
Store most chef fresh in original wrapping as long as it is
airtight and moisture-proof. Rewrap if necessary.
Leftovers
Cover leftovers with plastic wrap or aluminum foil. Plastic
containers with tight lids can also be used.
13
Page 14
USING YOUR REFRIGERATOR
STORING FROZEN FOOD
NOTE: For further information about preparing food for
freezing or food storage times, check a freezer guide or a
reliable cookbook.
Packaging
Successful freezing depends on correct packaging. When
you close and seal the package, it must not allow air or
moisture in or out. If you do, you could have food odor
and taste transfer throughout the refrigerator and also dry
out frozen food.
Follow package or container instructions for proper
freezing methods.
Do not use:
Bread wrappers
Non-polyethylene plastic containers
Containers without tight lids
Wax paper or wax-coated freezer wrap
Thin, semi-permeable wrap
Freezing
Your freezer will not quick-freeze any large quantity of
food. Do not put more unfrozen food into the freezer than
will freeze within 24 hours (no more than 2 to 3 lbs of food
per cubic foot of freezer space). Leave enough space in
the freezer for air to circulate around packages. Be careful
to leave enough room at the front so the door can close
tightly.
Storage times will vary according to the quality and type
of food, the type of packaging or wrap used (airtight and
moisture-proof) and the storage temperature. Ice crystals
inside a sealed package are normal. This simply means
that moisture in the food and air inside the package have
condensed, creating ice crystals.
NOTE: Allow hot foods to cool at room temperature for
30 minutes, then package and freeze. Cooling hot foods
before freezing saves energy.
NOTE: Do not store food near the sensor; it may cause
the sensor to malfunction.
REFRIGERATOR SHELVES
The shelves in your refrigerator are adjustable to meet
your individual storage needs. These units are all glass
shelves.
Storing similar food items together in your refrigerator and
adjusting the shelves to fit different heights of items will
make finding the exact item you want easier; it will also
reduce the amount of time the refrigerator door is open,
saving energy.
IMPORTANT: Do not clean glass shelves with warm
water when they are cold. Shelves may break if exposed
to sudden temperature changes or impact, such as
bumping. For your protection, glass shelves are made
with tempered glass, which will shatter into small pebblesized pieces.
NOTE: Glass shelves are heavy. Use special care when
removing them to avoid dropping them.
Adjusting Shelves
Remove shelves from the shipping position and replace
shelves in the position you want.
To remove a shelf:Tilt up the front of the shelf in the
direction of (1) and lift it in the direction of (2). Pull the
shelf out.
To replace a shelf : Tilt the front of the shelf up and
guide the shelf hooks into the slots at a desired height.
Then lower the front of the shelf so that the hooks drop
into the slots.
WARNING
Suffocation Hazard
When using dry ice, provide adequate ventilation.
Dry ice is frozen carbon dioxide (CO )2. When it
vaporizes, it can displace oxygen, causing dizziness,
light-headedness, unconsciousness and death by
suffocation. Open a window and do not breathe
the vapors.
NOTE: Make sure that shelves are leveled from one side to
the other. Failure to do so may result in the shelf falling or
spilling food.
14
Page 15
USING YOUR REFRIGERATOR
SNACK PAN
While holding the chef fresh with one hand, pull it forward
slightly. Lift slightly and pull it out.
CRISPER HUMIDITY CONTROL
You can control the amount of humidity in the moisturesealed crispers. Adjust the control to any setting between
and .
lets moist air out of the crisper for best storage of
fruits.
keeps moist air in the crisper for best storage of
fresh, leafy vegetables.
You can store small vegetables or fruits requiring more or
less humidity in separate drawers.
To remove the crisper door flap:
1. Raise the door as high as it will open.
2. Using your finger, press the plastic hinge toward the
center of the door flap.
3. Lift the door out of its place.
4. Replacement is the opposite of removal.
OPTIBIN CRISPERS
The OptiBin Crispers provide fresher-tasting fruit and
vegetables by letting you easily control humidity inside the
crisper. The OptiBin Crispers include: 1) a humidity
control knob at the front of the crisper cover and 2) a
large lattice on the inner surface of the cover to hold
or release moisture.
To remove the glass:
1. Lift up the glass after inserting a screwdriver under the
criper cover.
2. Pull up and out.
To remove the crisper:
1. Slide crisper straight out to the stop.
2. Lift the front of the crisper, then pull it out to remove.
3. Replace the crisper by sliding it back in fully past the
drawer stop.
15
Page 16
USINGYOURREFRIGERATOR
USING YOUR REFRIGERATOR
CRISPER COVER WITH LATTICE ON INNER
SURFACE
To remove the crisper cover:
1. Remove both crisper drawers.
2. While holding the crisper cover support (2), pull the
cover up and out(1).
WARNING: Be careful when handing glass cover since
glass is not attached to cover.
To remove the lattice on inner surface:
DOOR RACKS
The door racks may be removed for easier cleaning.
Snap-on Door Racks
To remove the racks:
1. Remove all items in the door racks.
2. Push the rack against the inside wall of the door (A)
and lift up the door rack (B).
To replace the racks:
1.
Hold either end of the do or rack against the ins ide wall of the d oor.
2. Push down the rack until it locks in place.
DESIGN-A-DOOR
1. Bins can be moved to either side of the door.
1. Remove crisper cover(as illustrated above).
2. Hold the glass cover and overtum crisper cover.
3. For each lattice hold lattice and pull sides of the cover
outward to remove lattice.
To replace lattice on inner surface:
1. For each lattice insert middle tab in 1 (closed to glass
cover)and pull sides of the cover to insert lattice.
2.
To remove the bin,simply lift the bin up and pull straight out.
3. To replace the bin, slide it in above the desired
support button and push down until it locked completely
so that
4. To move to lowest position, make sure if all bins are
correctly assembled so that they don
“tick” sounds can be heard.
Õt fall out of door.
Warning: Somebody can be hurt if door bins are not
firmly assembled.
NOTE: Do not adjust a bin that is loaded with food.
16
Page 17
USING YOUR REFRIGERATOR
DAIRY BIN
1. To remove the dairy bin, simply lift it and pull straight
out.
2. To replace the dairy bin, slide it in above the desired
location and push down until it stops.
FREEZER WIRE DOOR RACKS
Tilt-out Door Basket (on some models)
You can remove foods easily by tilting out the wire basket
in the freezer compartment.
ICE BIN
1. To remove ice bin, pull it out as it comes.
Tilt up the front of the ice bin and pull straight out.
2. To Install, insert ice bin into frame rails and push back
into place.
WIRE DURABASE
1. To remove wire Durabase, pull wire durabase out to full
extension.
Tilt up the front of the wire Durabase and pull it straight
out.
2. To install, insert the wire Durabase into frame rails and
push back into place.
1. To remove the freezer door rack, pull the bracket
outward until you hear a clicking sound; then remove
the wire rack.
2. To replace the freezer door rack, hook the end of the
rack in the bracket, and push down until the rack locks
into place.
1
2
WIRE BASKET
1.
To remove the wire basket, pull it out as far as it goes. Tilt the
front up and Pill it straight out.
2. To replace the wire basket, place it in the frame rails
and push it back into place.
17
Page 18
USINGYOURREFRIGERATOR
WIRE BASKET DIVIDER(on
The wire basket divider allows the option to organize the wire basket area into sections.
To remove, pull divider staight up.
1.
To install, hook top corners of divider over top
2.
horizontal basket rungs.
DRAWERTRAY (on
The drawer tray prevents small food items from fallingbetween the basket rungs.
som
som
emodels
emodels
)
)
TRIPLE TWIST ICE TRAY
If the tray is filled with water to the highest level, it willbe difficult to remove ice cubes.
For quick freeze, adjust the freezer dial to 3.
To
removei
Twist the knob clockwise completely.
cecubes,twis
tthetray
.
CAUTION
If you twist the knob before the freezers, it will spill intothe ice bin and the cubes there will be frozen together.
18
Page 19
CARE AND CLEANING
PLASTIC PARTS (covers and panels)
WARNING
Explosion Hazard
Use non-flammable cleaner.
Failure to do so can result in death, explosion, or fire.
Both the refrigerator and freezer sections defrost
automatically. However, clean both sections about once
a month to prevent odors. Wipe up spills immediately.
GENERAL CLEANING TIPS
Unplug refrigerator or disconnect power.
Remove all removable parts, such as shelves,
crispers, etc.
Use a clean sponge or soft cloth and a mild detergent in
warm water. Do not use abrasive or harsh cleaners.
Hand wash, rinse and dry all surfaces thoroughly.
Do not use paper towels, window sprays, abrasive
cleansers, or flammable fluids. These can scratch or
damage the material.
CONDENSER COILS
Remove grille base. (See the grille base section on
page 8.)
Use a vacuum cleaner with an extended attachment to
clean condenser coils.
Vacuum coils when dusty or dirty. Coils may need to be
cleaned as often as every other month.
Replace grille base.
LIGHT BULB REPLACEMENT
WARNING
Electrical Shock Hazard
Before replacing a burned-out light bulb, either unplug
the refrigerator or turn off power at the circuit breaker
or fuse box.
NOTE: Moving the control to the OFF position
does not remove power to the light circuit.
Plug in refrigerator or reconnect power.
OUTSIDE
Waxing external painted metal surfaces helps provide rust
protection. Do not wax plastic parts. Wax painted metal
surfaces at least twice a year using appliance wax (or
auto paste wax). Apply wax with a clean, soft cloth.
For products with a stainless steel exterior, use a clean
sponge or soft cloth and a mild detergent in warm water.
Do not use abrasive or harsh cleaners. Dry thoroughly
with a soft cloth.
INSIDE WALLS (allow freezer to warm up so
cloth won’
To help remove odors, you can wash the inside of the
refrigerator with a mixture of baking soda and warm water.
Mix 2 tablespoons baking soda to 1 quart of water (26 g
soda to 1 liter water.) Be sure the baking soda is
completely dissolved so does it not scratch the surfaces
of the refrigerator.
t stick)
DOOR LINERS AND GASKETS
Do not use cleaning waxes, concentrated detergents,
bleaches, or cleaners containing petroleum plastic parts.
NOTE: Not all appliance bulbs will fit your refrigerator. Be
sure to replace the bulb with one of the same size, shape
and wattage.
To change the refrigerator light:
1. Unplug the power cord from the outlet.
2. Remove refrigerator shelves.
3. Release the hooks on both ends of the light shield and
pull the shield down to remove it.
4. Turn the bulb counterclockwise.
5. Assembly is the reverse order of disassembly.
19
Page 20
To change the freezer light:
1. Unplug refrigerator or disconnect power.
2. Reach behind light shield to remove bulb.
3. Replace bulb with a 40-watt appliance bulb.
4. Plug in refrigerator or reconnect power.
POWER INTERRUPTIONS
If the electricity goes off, call the power company and ask
how long it will be off.
1. If the power will be out for 24 hours or less, keep
both refrigerator doors closed to help foods stay
cold and frozen.
WHEN YOU GO ON VACATION
If you choose to leave the refrigerator on while you
are away, follow these steps to prepare your refrigerator
before you leave.
1. Use up any perishables and freeze other items.
2. Empty the ice bin.
If you choose to turn the refrigerator off before you
leave, follow these steps.
1. Remove all food from the refrigerator.
2. Depending on your model, set the thermostat control(refrigerator control) to OFF. See the Setting the
Controls section.
3.
Clean refrigerator, wipe it and dry well.
4. Tape rubber or wood blocks to the tops of both doors to
prop them open far enough for air to get in. This stops
odor and mold from building up.
2. If the power will be out for more than 24 hours:
a) Remove all frozen food and store it in a frozen
food locker.
OR
b)
Place 2 lbs of dry ice in the freezer for every cubic
foot of freezer space. This will keep the food frozen
for two to four days. While handling dry ice, wear
gloves to protect your hands from frostbite.
OR
c)
If neither a food locker nor dry ice is available,
consume or can perishable food at once.
Page 21
TROUBLESHOOTING GUIDE
UNDERSTANDING SOUNDS YOU MAY HEAR
Your new refrigerator may make sounds that your old one
didn’t make. Because the sounds are new to you, you
might be concerned about them. Most of the new sounds
are normal. Hard surfaces, like the floor, walls and
cabinets, can make the sounds seem louder than they
actually are. The following describes the kinds of sounds
and what may be making them.
The defrost timer will click when the automatic defrost
cycle begins and ends. The thermostat control (or
refrigerator control, depending on the model) will also
click when cycling on and off.
Rattling noises may come from the flow of refrigerant, the
water line, or items stored on top of the refrigerator.
Your refrigerator is designed to run more efficiently
to keep your food items at the desired temperature.
The high efficiency compressor may cause your new
refrigerator to run longer than your old one, and
you may hear a pulsating or high-pitched sound.
You may hear the evaporator fan motor circulating the air
through the refrigerator and freezer compartments.
As each cycle ends, you may hear a gurgling sound due
to the refrigerant flowing in your refrigerator.
Contraction and expansion of the inside walls may cause
a popping noise.
Water dripping on the defrost heater during a defrost
cycle may cause a sizzling sound.
You may hear air being forced over the condenser by the
condenser fan.
You may hear water running into the drain pan during the
defrost cycle.
REFRIGERATOR DOES NOT OPERATE
Check if...Then...
The power supply cord is unplugged.Firmly plug the cord into a live outlet with proper voltage.
A household fuse has blown or circuitReplace the fuse or reset the circuit breaker.
breaker tripped.
The refrigerator control is set to the OFF position.Refer to the Setting the Controls section on page 12.
Refrigerator is in the defrost cycle.Wait about 30 minutes for defrost cycle to end.
VIBRATION OR RATTLING NOISE
Check if...Then...
The refrigerator is not resting solidly on Floor is weak or uneven or leveling legs need adjusting.
the floor.See Installation section on page 11.
LIGHTS DO NOT WORK
Check if...Then...
The power supply cord is unplugged.Firmly plug the cord into a live outlet with proper voltage.
Light bulb is loose in the socket.Turn the refrigerator control to the OFF position and unplug
the refrigerator. Gently remove the bulb and reinsert. Then
plug in refrigerator and reset the refrigerator control.
Light bulb has burned out.Replace with an appliance bulb of the same wattage, size
and shape available at your local hardware store. (See the
Changing the Light Bulb(s) section on pages 19 - 20.) Turn
the temperature control to the OFF position and unplug the
refrigerator prior to replacement.
21
Page 22
TROUBLESHOOTING GUIDE
COMPRESSOR MOTOR SEEMS TO RUN TOO MUCH
Check if...Then...
The refrigerator that was replaced was anModern refrigerators with more storage space require
older model.more operating time.
The room temperature is hotter than normal.The motor will run longer under warm conditions. At normal
room temperatures, expect your motor to run about 40% to
80% of the time. Under warmer conditions, expect it to run
even more often.
The door is opened often or a large amountAdding food and opening the door warms the refrigerator.
of food has just been added.It is normal for the refrigerator to run longer in order to cool
the refrigerator back down. Adding a large amount of food
warms the refrigerator. See the Food Storage Guide section
on page 13. In order to conserve energy, try to get everything
you need out of the refrigerator at once, keep food organized
so it is easy to find and close the door as soon as the food
is removed.
The refrigerator was recently plugged in andThe refrigerator will take up to 24 hours to cool
the refrigerator control was set correctly completely.
The refrigerator control was not set correctly for the
surrounding conditions.
The doors are not closed completely.Push the doors firmly shut. If they will not shut all the way, see
The condenser coils are dirty.This prevents air transfer and makes the motor work harder.
See the Adjusting control settings section on page 16.
Doors will not close completely below.
Clean the condenser coils. Refer to the Care and Cleaning
section on page 19.
DOORS WILL NOT CLOSE COMPLETELY
Check if...Then...
The refrigerator is not level.See the Installation section on page 10 to level refrigerator.
Food packages are blocking the door open.Rearrange food containers to clear door and door shelves.
The ice bin, crisper cover, pans, shelves, door bins Push bins all the way in and put crisper cover, pans, shelves
or baskets are out of position.and baskets into their correct positions. See the
Refrigerator section on pages 12.
The gaskets are sticking.Clean gaskets and the surface that they touch. Rub a thin
coat of paraffin wax on the gaskets after cleaning.
The refrigerator wobbles or seems unstable.Level the refrigerator. Refer to the Door Closing and
Alignment section on page 11.
Using Your
The doors were removed during product installation Remove and replace the doors according to the Removing,
and not properly replaced. Reversing and Replacing Refrigerator Doors section
on pages 9 or call a qualified service technician.
FROST OR ICE CRYSTALS ON FROZEN FOOD
Check if...Then...
The door is not closing properly.See Doors will not close completely above.
The door is opened often.When the door is opened, warm, humid air is allowed in
the freezer resulting in frost.
22
Page 23
TROUBLESHOOTING GUIDE
ICE HAS OFF-TASTE OR ODOR
Check if...Then...
The icemaker was recently installed.Discard first few batches of ice to avoid discolored or
off-flavored ice.
The ice has been stored for too long.Throw away old ice and make new supply.
The food has not been wrapped tightly inRewrap foods since odors may migrate to the ice if food
either compartment.is not wrapped properly.
The water supply contains minerals such as sulfur.A filter may need to be installed to eliminate taste and
odor problems.
The interior of refrigerator needs cleaning.See Care and Cleaning section on page 19.
Ice storage bin needs cleaning.Empty and wash bin. Discard old cubes.
THERE IS WATER IN THE DEFROST DRAIN PAN
Check if...Then...
The refrigerator is defrosting.The water will evaporate. It is normal for water to drip into the
defrost pan.
It is more humid than normal.Expect that the water in the defrost pan will take longer to
evaporate. This is normal when it is hot or humid.
THE REFRIGERATOR SEEMS TO MAKE TOO MUCH NOISE
Check if...Then...
The sounds may be normal for your refrigerator.Refer to the Understanding Sounds You May Hear section on
page 21.
THE ICEMAKER IS NOT PRODUCING ICE OR ICE CUBES ARE FREEZING TOO SLOWLY
Check if...Then...
The freezer temperature is cold enough to produce ice. Wait 24 hours after hook-up for ice production. See the Setting
the Controls section on page 12
Door left open.Check to see if something is holding the door open.
CUBES PRODUCED BY ICEMAKER ARE TOO SMALL
Check if...Then...
Smaller cube size level is selected.Select larger cube size using cube size selector.
Water shutoff valve connecting refrigerator to water Call a plumber to clear the valve.
line may be clogged.
THE DOORS ARE DIFFICULT TO OPEN
Check if...Then...
The gaskets are dirty or sticky.Clean gaskets and the surfaces that they touch. Rub a thin
coat of appliance polish or kitchen wax on the gaskets after
cleaning
The door is reopened within a short time after havingWhen you open the door, warmer air enters the refrigerator.
been opened. As the warm air cools, it can create a vacuum. If the door is
hard to open, wait 5 minutes to allow the air pressure to
equalize, then see if it opens more easily.
23
Page 24
TROUBLESHOOTING GUIDE
TEMPERATURE IS TOO WARM OR THERE IS INTERIOR MOISTURE BUILDUP
Check if...Then...
The air vents are blocked. Cold air circulatesLocate air vents by using your hand to sense airflow and
from the freezer to the fresh food section andmove all packages that block vents and restrict airflow. Refer
back again through air vents in the wall dividingto multi flow on page 12 for the location of
the two sections.air vents.
The doors are opened often.When the door is opened, warm humid air is allowed into
the refrigerator. The more the door is opened, the faster the
humidity builds up, and the more warm air the refrigerator
must cool. In order to keep the refrigerator cool, try to get
everything you need out of the refrigerator at once, keep
food organized so it is easy to find and close the door as
soon as the food is removed.
The control is not set correctly for the surrounding Refer to the Setting the Controls section on page 12.
conditions.Wait 24 hours for temperatures to stabilize or even out. If the
temperature is too cold or too warm, move the dial one
number at a time.
A large amount of food has just been addedAdding food warms the refrigerator. It can take a few hours
to the refrigerator or freezer.for the refrigerator to return to normal temperature.
The food is not packaged correctly.Wrap food tightly and wipe off damp containers prior to
storing in the refrigerator to avoid moisture accumulation. If
necessary, repackage food according to the guidelines in the
Food Storage Guide section on page 13.
The doors are not closing completely.See Doors will not close completely on page 23
The weather is humid.In humid weather, air carries moisture into refrigerator
when doors are opened.
A self-defrost cycle was completed.It is normal for droplets to form on the back wall after the
refrigerator self-defrosts.
24
Page 25
NOTES
25
Page 26
NOTES
26
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.