LG LBC2252, LDC2272, LRBC2051 User Manual

BOTTOM FREEZER REFRIGERATOR
Owner’s Manual
Please read this guide thoroughly before operating and keep it handy for reference at all times.
REFRIGERADOR CON CONGELADOR INFERIOR
Manual de Usuario
Lea detenidamente estas instrucciones antes de usar el refrigerador y guárdelas como referencia para el futuro.
Models / Modelos
LDC2272#** LBC2252#**
P/No. MFL48165101
TABLE OF CONTENTS
English Version 2 Spanish Version 36
Warranty (U.S.A.)
Safety Instructions 5 -6
Grounding Requirements
Parts and Features
Refrigerator Installation
Unpacking Your Refrigerator Installation
Base Grille
Removing, Reversing and Replacing
Your Refrigerator Doors Door Closing and Alignment
Using Your Refrigerator 18 -25
Ensuring Proper Air Circulation 18 Multi Flow Door Alarm Setting the Controls 18 -19 Adjusting Control Settings 19 Food Storage Guide 20 Storing Frozen Food 20 Refrigerator Shelves 21 Chef Fresh / Snack Pan 22 Crisper Humidity Control 22 Optibin Crisper 22 Crisper cover with lattice on inner surface 23
7 - 9
-17
10
10 10
10
11 - 17
17
18 18
3
6
Door Racks 23 Design-A-Door 23
Dairy Bin 24
Ice Bin 24 DuraBase 24 DuraBase Divider 24
Guide-Out Drawer Basket 25 Tilting Door 25
Wire Durabase 25
Frezzer Shelf 25
Care and Cleaning 26 -27
General Cleaning Tips 26 Outside 26
Inside Walls 26 Door Liner and Gaskets 26 Plastic Parts 26 Condenser Coils 26 Light Bulb Replacement Power Interruptions 27 When you go on vacation 27
About the Custom Cube Icemaker
Connecting the Water Line 29 -
Troubleshooting Guide 32 -35
26 -27
28
31
2
visit our web site/http://www.lgservice.com
LG Electronics
LIMITED WARRANTY
United States of America
LG Electronics will repair or at its option replace, without charge, your product which proves to be defective in material or workmanship under normal use during the warranty period listed below from the date of original purchase.
This warranty is good only to the original purchaser of the product during the warranty period as long as it is in the U.S. including Alaska, Hawaii, and U.S. Territories.
LG Refrigerator / Freezer Warranty Period
Product Parts Labor
Refrigerator / Freezer 1 year 1 year [In-Home Service (Except Model GR-051)] Sealed System 7 years 1 year [In-Home Service (Except Model GR-051)] (Compressor, Condenser, Evaporator)
No other express warranty is applicable to this product. THE DURATION OF ANY IMPLIED WARRANTIES. INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY, IS LIMITED TO THE DURATION OF THE EXPRESS WARRANTY HEREIN. LG ELECTRONICS SHALL NOT BE LIABLE FOR THE LOSS OF USE OF THE PRODUCT, INCONVIENCE, LOSS OR ANY OTHER DAMAGES, DIRECT OR CONSEQUENTIAL, ARISING OUT OF THE USE OF OR INABILITY TO USE, THIS PRODUCT OR FOR ANY BREACH OF ANY EXPRESS OR IMPLIED WARRANTY, INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY APPLICABLE TO THIS PRODUCT.
Some States do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts; so these limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
THE ABOVE WARRANTY DOES NOT APPLY TO:
1. Service trips to your home to deliver and pickup, install, instruct, or replace house fuses or correct house wiring or plumbing, or correction of unauthorized repairs.
2. Damage to the product caused by accident, pests, fire, floods, or acts of God.
3. Repairs when your LG product is used in other than normal, single-family household use.
4. Damage resulting from accident, alteration, misuse, abuse, or improper installation. Damages caused during and/or after delivery.
5. Display, discount, or refurbished units purchased with scratches, dents, or defects.
6.
Proof of purchase is required and must be provided to LG in order to validate warranty.
Therefore, these costs are paid by the consumer.
If the product is installed outside the normal service area, any cost of transportation involved in the repair of the product, or the replacement of defective parts, shall be borne by the owner.
CUSTOMER ASSISTANCE NUMBERS:
To obtain Warranty Coverage: Retain your Bill of Sale to prove date of purchase.
A Copy of your Sales Receipt must be submitted at the time warranty service is provided.
To obtain Product or Customer
Service Assistance: Press the appropriate menu option, and have your product type
To obtain the nearest Authorized Service Center:
Call 1-800-243-0000
(24 hrs a day, 7 days per week, 365 days per year)
(Refrigerator), model number, serial number, and ZIP/Postal Code ready.
Call 1-800-243-0000
(24 hrs a day, 7 days per week, 365 days per year)
Press the appropriate option, and have your product type (Refrigerator), model number, serial number, and ZIP/Postal Code ready.
3
Visite nuestro sitio web/http://www.lgservice.com
LG Electronics
GARANTÍA LIMITADA
Estados Unidos de América
LG Electronics reparará o en su defecto reemplazará sin cargo, el producto defectuoso en material o mano de obra bajo uso normal durante el periodo de garantía que se menciona a continuación desde la fecha original de compra.
Esta garantía es válida solo para el comprador original del producto durante el periodo de garantía mientras permanezca en los E.E. U.U. Incluyendo Alaska, Hawaii y otros territorios de E.E.U.U.
Período de Garantía del refrigerador/Congelador LG
Producto
Refriger Sistema Sellado 7 años 1 año [Servicio a domicilio (Excepto Modelo GR-051)] (Compresor, Condensador, Evaporador)
a
dor/Co
ngelador
Partes Mano de Obra
1 año 1 año [Servicio a domicilio (Excepto Modelo GR-051)]
No se aplicará otro tipo de garantía a este producto. LA DURACION DE OTRAS GARANTIAS , INCLUYENDO LA DE COMPRA, ESTAN LIMITADAS A LA DURACION DE ESTA GARANTIA. LG ELECTRONICS NO SE HACE RESPONSABLE POR LA PERDIDA EN EL USO DEL PRODUCTO, POR INCONVENIENCIA O CUALQUIER OTRO DAÑO DIRECTO O CONSECUENTE QUE PROVENGA DEL USO Y/O NO USO DE ESTE PRODUCTO O POR ALGUNA VIOLACION A LAS GARANTIAS IMPLEMENTADAS INCLUYENDO LA GARANTIA DE COMPRA APLICADA A ESTE PRODUCTO.
Algunos estados no permiten la exclusión o limitación de daños incidentales o consecuenciales o limitaciones en cuanto al tiempo que dura una garantía implícita; por lo que algunas de estas limitaciones o exclusiones pueden no aplicarse a usted. Esta garantía le otorga derechos legales específicos y usted puede además tener otros derechos los cuales varían de Estado a Estado.
LA GARANTIA ANTERIOR NO APLICA A :
1.
Servicio a su casa para entregar, recoger, instalar o reemplazar fusibles caseros, corregir cableado casero o plomería corrección de reparaciones no autorizadas.
2.
Daño al producto causado por accidente, plagas, incendios, inundaciones o actos por naturaleza.
3.
Reparaciones cuando su producto LG sea usado diferente a lo normal. Daño resultante de accidente, alteración, mal uso o instalación inadecuada.
4.
5.
Daños causados durante y después de la entrega.
6.
Reemplazo, descuento o restauración de unidades compradas con rayones, abolladuras o defectos.
La prueba de la compra se requiere y se debe proporcionar a LG para validar la garantia.
Por lo tanto, estos costos serán pagados por el consumidor.
Si el producto es instalado fuera del área normal de servicio, cualquier costo de transportación relacionado en la reparación del producto, o el reemplazo de partes defectuosas, serán cargados al propietario.
NÚMEROS DE ASISTENCIA AL CLIENTE:
Para obtener cobertura de la Garantía:
Para obtener información:
Servicio de Asistencia:
Para obtener el Centro de Servicio Autorizado más cercano:
Conserve su factura para comprobar la fecha de compra.
Una copia de su recibo de compra debe ser entregada cuando se le proporcione el servicio de garantía.
Llame al
(24 hrs al día, 7 días por semana, 365 días al año)
Presione la opción de menú apropiado, y tenga su tipo de producto (Refrigerador), número de modelo, número de serie, y ZIP / Código Postal listos.
Llame al
(24 hrs al día, 7 días por semana, 365 días al año)
Presione la opción adecuada, y tenga su tipo de producto(Refrigerador), número de modelo, número de serie, y ZIP /código Postal listos.
1-800-243-0000
1-800-243-0000
4
IMPORTANT SAFETY INSTRUCTIONS
SAFETY MESSAGES
This guide contains many important safety messages. Always read and obey all safety messages.
This is the safety alert symbol. It alerts you to safety messages that inform you of hazards that can kill or hurt you or others, or cause damage to the product.
All safety messages will be preceded by the safety alert symbol and the hazard signal word DANGER, WARNING, CAUTION. These words mean:
You will be killed or seriously injured if you don’t follow instructions.
DANGER
WARNING
You can be killed or seriously injured if you don’t follow instructions.
CAUTION
All safety messages will identify the hazard, tell you how to reduce the chance of injury and tell you what can happen if the instructions are not followed.
Indicates an imminently hazardous situation which, if not avoided,
may result in minor or moderate injury, or product damage only.
WARNING
To reduce the risk of fire, electric shock, or injury to persons when using your product, basic safety precautions should be followed, including the following:
NEVER unplug your refrigerator by pulling on the power cord. Always grip the plug firmly and pull it straight out from the outlet.
Repair or replace immediately all electric service cords that have become frayed or otherwise damaged. Do not use a cord that shows cracks or abrasion damage along its length or at either the plug or connector end.
When moving your refrigerator away from the wall, be careful not to roll over or damage the power cord.
DO NOT store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
DO NOT allow children to climb, stand or hang on the refrigerator doors or shelves in the refrigerator. They could damage the refrigerator and seriously injure themselves.
Keep fingers out of “pinch point” areas; clearances between the doors and cabinet are necessarily small. Be careful when you open the doors when children are in the area.
Unplug your refrigerator before cleaning or making any repairs. NOTE: We strongly recommend that any servicing be
performed by a qualified individual.
Before replacing a burned-out light bulb, unplug the refrigerator or turn off power at the circuit breaker or fuse box in order to avoid contact with a live wire filament. (A burned­out light bulb may break when being replaced.) either or both controls to the OFF position does not remove power to the light circuit.
Do not store bottles in the freezer compartment - they may break when frozen, causing damage.
NOTE: Setting
For personal safety, this appliance must be properly grounded. Have the wall outlet and the circuit checked by a qualified electrician to make sure the outlet is properly grounded.
Read all instructions before using this appliance. Use this appliance only for its intended purpose as described
in this use and care guide. After your refrigerator is in operation, do not touch the cold
surfaces in the freezer compartment when hands are damp or wet. Skin may adhere to the extremely cold surfaces.
In refrigerators with automatic icemakers, avoid contact with the moving parts of the ejector mechanism, or with the heating element that releases the cubes. DO NOT place fingers or hands on the automatic icemaking mechanism while the refrigerator is plugged in.
DO NOT refreeze frozen foods which have thawed completely. The United States Department of Agriculture in Home and Garden Bulletin No. 69 says:
“...You may safely refreeze frozen foods that have thawed if
they still contain ice crystals or if they are still cold below 40°F (4°C).”
“...Thawed ground meats, poultry, or fish that have any off-odor or off-color should not be refrozen and should not be eaten. Thawed ice cream should be discarded. If the odor or color of any food is poor or questionable, get rid of it. The food may be dangerous to eat.”
“Even partial thawing and refreezing reduces the eating quality of foods, particularly fruits, vegetables and prepared foods. The eating quality of red meats is affected less than that of many other foods. Use refrozen foods as soon as possible to save as much of their quality as you can.”
SAVE THESE INSTRUCTIONS
5
DANGER: RISK OF CHILD ENTRAPMENT
Child entrapment and suffocation are not problems of the past. Junked or abandoned refrigerators are still dangerous... even if they will sit for “just a few days”. If you are getting rid of your old refrigerator, please follow the instructions at right to help prevent accidents.
BEFORE YOU THROW AWAY YOUR OLD REFRIGERATOR OR FREEZER
Take off the doors.
Leave the shelves in place so that children may not easily climb inside.
CFC DISPOSAL
Your old refrigerator may have a cooling system that used If you are throwing away your old refrigerator, make sure CFCs (chlorofluorocarbons). CFCs are believed to harm the CFC refrigerant is removed for proper disposal by a stratospheric ozone. qualified servicer. If you intentionally release this CFC
refrigerant, you can be subject to fines and imprisonment under provisions of environmental legislation.
GROUNDING REQUIREMENTS
IMPORTANT:
Please read carefully.
TO CONNECT ELECTRICITY
WARNING
Electrical Shock Hazard
FOR PERSONAL SAFETY, this appliance must be
properly grounded. Have the wall outlet and the circuit checked by a qualified electrician to make sure the outlet is properly grounded.
3-prong grounding type wall receptacle
3-prong grounding plug
Ensure proper ground exists before use.
RECOMMENDED GROUNDING METHOD
The refrigerator should always be plugged into its own individual properly grounded electrical outlet rated for 115 Volts, 60 Hz, AC only, and fused at 15 or 20 amperes. This provides the best performance and also prevents overloading house wiring circuits which could cause a fire hazard from overheated wires. It is recommended that a
separate circuit serving only this appliance be provided. Use a receptacle which cannot be turned off with a switch or pull chain. Do not use an extension cord.
Where a standard two-prong wall outlet is encountered, it is your personal responsibility and obligation to have it replaced with a properly grounded three-prong wall outlet.
Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.
NOTE: Before performing any type of installation, cleaning, or removing a light bulb, turn the control (Thermostat, Refrigerator Control or Freezer Control, depending on the model) to OFF and then disconnect the refrigerator from the electrical source. When you are finished, reconnect the refrigerator to the electrical source and reset the control (Thermostat, Refrigerator Control or Freezer Control, depending on the model) to the desired
setting.
USE OF EXTENSION CORDS
Because of potential safety hazards under certain conditions, we strongly recommend against the use of an extension cord.
However, if you still elect to use an extension cord, it is absolutely necessary that it be a UL-listed (in the United States) or ACNOR (Canada), 3-wire grounding type appliance extension cord having a grounding type plug and outlet, and that the electrical rating of the cord be 15 amperes (minimum) and 120 volts.
Use of an extension cord will increase the clearance needed for the back of the refrigerator.
WARNING
POWER CORD REPLACEMENT
If the power cord is damaged, it must be replaced by the manufacturer, by our service center or by qualified personal by LG Electronics, to avoid some risk.
6
A
B
PARTS AND FEATURES
G
K
D
E
F
H
J
C
L
M
N
O
P
I
Q
R
Use this section to become more familiar with the parts and features.
NOTE:This guide covers several different models. The refrigerator you have purchased may have some or all of the items listed below.The locations of the features shown below may not match your model.
A
Digital Sensor Control
B
Refrigerator Light
C
Shelves
D
Temperature Control*
E
Chef Fresh / Snack Pan
F
Can Dispenser*
Optibin Crisper
G
Keeps fruits and vegetable fresh and crisper
H
Ice Bin
I
Ice Tray (Inside of H)*
J
Durabase
K
Divider
L
Dairy Bin
M
Design-A-Door
N
Egg Box
O
Refrigerator Door Rack
Freezer Light
P
Pull out Drawer
Q
R
Customcube Icemaker*
*on some models
7
A
B
C
D
E
F
G
PARTS AND FEATURES
J
K
L
M
N
N
HH
I
Use this section to become more familiar with the parts and features.
NOTE:This guide covers several different models. The refrigerator you have purchased may have some or all of the items listed below.The locations of the features shown below may not match your model.
A
Digital Sensor Control
B
Refrigerator Light
C
Shelves
D
Chef Fresh / Snack Pan
E
Optibin Crisper Keeps fruits and vegetable fresh and crisper
Ice Bin
F
G
Ice Tray (Inside of F)*
H
Durabase
I
Divider
J
Dairy Bin
K
Design-A-Door
L
Pull out Drawer
M
Refrigerator Door Rack
N
Freezer Light
O
Customcube Icemaker*
*on some models
O
8
PARTS AND FEATURES
A
B
C
D
E
F
G
H
I
J
K
L
M
N
Use this section to become more familiar with the parts and features.
NOTE:This guide covers several different models. The refrigerator you have purchased may have some or all of the items listed below.The locations of the features shown below may not match your model.
Digital Sensor Control
A
B
Refrigerator Light
C
Shelves
D
Snack Pan
E
Optibin Crisper Keeps fruits and vegetable fresh and crisp
Ice Trays*
F G
Ice Bin
H
Wire Durabase
I
Dairy Bin
J
Design-A-Door
K
Wire Freezer Shelf
L
Refrigerator Door Rack
Freezer Light
M
Freezer Door Rack
N
*on some models
9
REFRIGERATOR INSTALLATION
WARNING
Excessive Weight Hazard
Use two or more people to move and install refrigerator. Failure to do so can result in back or other injury.
UNPACKING YOUR REFRIGERATOR
Remove tape and any temporary labels from your refrigerator before using. Do not remove any warning­type labels, the model and serial number label, or the TechSheet that is attached to back wall of the refrigerator.
To remove any remaining tape or glue, rub the area briskly with your thumb. Tape or glue residue can also be easily removed by rubbing a small amount of liquid dish soap over the adhesive with your fingers. Wipe with warm water and dry.
Do not use sharp instruments, rubbing alcohol, flammable fluids or abrasive cleaners to remove tape or glue. These products can damage the surface of your refrigerator. For more information, see the Important Safety Instructions section.
Refrigerator shelves are installed in the shipping position.
Please reinstall shelves according to your individual storage needs.
When Moving Your Refrigerator:
Your refrigerator is heavy. When moving the refrigerator for cleaning or service, be sure to protect the floor. Always pull the refrigerator straight out when moving it. Do not wiggle or walk the refrigerator when trying to move it, as floor damage could occur.
WARNING
3. Install this appliance in an area where the temperature
is between 55°F (13°C) and 110°F (43°C.) If the temperature around the appliance is too low or high, cooling ability may be adversely affected.
CAUTION: Avoid placing the unit near heat sources, direct sunlight or moisture.
NEXT
1. Clean your refrigerator thoroughly and wipe off all dust
accumulated during shipping.
2. Install accessories such as ice cube bin, drawers,
shelves, etc., in their proper places. They are packed together to prevent possible damage during shipment.
3. Let your refrigerator run for 2 or 3 hours before putting
food in it. Check the flow of cold air in the freezer compartment to ensure proper cooling. Your refrigerator is now ready for use.
WARNING:
Be careful when you work with hinge, base grille, stopper etc. You may be injured.
Do not put hands or metal sticks into air vents, base grille or bottom of refrigerator. You may be injured or receive an electrical shock.
BASE GRILLE
To remove the base grille:
1. Grasp the grille with both hands.
2. Pull the grille toward yourself. To install the base grille:
1. Place clips in openings in the metal panel.
2. Push the grille toward the refrigerator until it snaps
into place.
Explosion Hazard
Keep flammable materials and vapors, such as gasoline, away from refrigerator.
Failure to do so can result in death, explosion or fire.
INSTALLATION
1. Avoid placing the unit near heat sources, direct sunlight,
or moisture.
2. To avoid vibration, the unit must be level. If required,
adjust the leveling screws to compensate for unevenness of the floor. The front should be slightly higher than the rear to aid in door closing. Leveling screws can be turned easily by tipping the cabinet slightly. Turn the leveling screws clockwise ( ) to raise the unit, counterclockwise ( ) to lower it.
A proper distance from adjacent items
Please keep the refrigerator at a proper distance from other things. Too small a distance from adjacent items may result in lowered freezing capability and increased electricity consumption charges.
1”
10
(2.54 cm)
REFRIGERATOR INSTALLATION
HOW TO REMOVE DOOR HANDLES
T O O L S Y O U M A Y N E E D
10 mm 1/4 in 3/8 in
Hex head socket wrench
IMPORTANT: Before you begin, turn the refrigerator OFF and unplug it. Remove food and any adjustable door or utility bins from doors.
HOW TO REVERSE DOOR OPENING DIRECTION (when converting from the left-opening type to right­opening type)
1. Removing Refrigerator Door
Remove the top hinge cover (1).
Remove the 3 screws and lift off the top hinge (2).
Phillips screwdriver
Flat head screwdriver
1/4 in 3/32 in
Allen wrench
Lift the Refrigerator door (3) slightly and remove it.
Use a flat tip screwdriver to pry off top hole cover (4)
and attach it on the right.
Loosen the screw (5), remove the stoppers (6), and
attach them on the left (on the opposite side).
Loosen the pin (8) and remove it.
Loosen the 2 screws (9) and the 2 screws (10), and
lift off the middle hinge (11).
Use a flat tip screwdriver to pry off bottom hole cover
(7) and attach it on the right.
HOW TO REMOVE DOOR HANDLES
NOTE: Handle appearance may vary from illustrations on this page.
2.. Removing Refrigerator Handle
Loosen the set screws (1) with the 3/32” Allen wrench and remove the handle (2).
Loosen the handle mounting fasteners (3) with the 1/4” Allen wrench.
Carefully pry off the plug buttons (4).
Install the plug buttons (4) on the left side.
Install the handle mounting fasteners (3)
on the right side.
Allen Wrench
REFRIGERATOR INSTALLATION
3. Replacing Refrigerator Handle
Turn handle upside down (5)
••Place the handle (2) on the door by adjusting handle
footprints to fit mounting fastners and tighten the set screws (1) with the 3/32 ” Allen wrench.
4. Installing Refrigerator Door
Install the middle hinge (1) on the opposite side with the screws (2), and the screw (3).
Install the door (4) so that it fits onto the middle hinge
pin (5).
Install the top hinge (6) with screws.
Reinstall top hinge cover (7).
REFRIGERATOR INSTALLATION
HOW TO REMOVE AND INSTALL THE PULLOUT DRAWER
IMPORTANT: To avoid possible injury, product or property
damage, you will need two people to perform the following instructions.
1. Removing Pullout Drawer
Pull the drawer open to full lower extension. Remove the
lower basket (1) by lifting basket from rail system.
1
Press both hangers with yours thumbs to lift it up.
Separate the left and right rail cover
With both hands, hold both sides of the door and pull it up to separate it from the rails.
With both hands, hold the center of the bar and push it in to let both rails fitted simultaneously.
Remove the screws(2) of the rail on both sides.
2
CAUTION: When you remove the drawer, do not hold handle. If it comes off, it could cause personal injury.
CAUTION: When laying down the drawer, be careful not to damage the floor or hurt your feet by the sharp edges on hinge side.
13
REFRIGERATOR INSTALLATION
HOW TO REMOVE AND INSTALL THE
PULL OUT DRAWER
IMPORTANT: To avoid possible injur or product or property damage, you will need two people to perform the following instructions.
2. Installing Pullout Drawer
With both hands, hold the center of the bar and pull it out to let both rails out to full extension simultaneously.
Make sure you have a right rail cover for each side.
Right
Rail cover
Left
Rail cover
Align the top holes of the rail cover with the top holes of
the door supports to assemble the rail cover.
Hook door supports (1) into rail tabes (2) .
1
2
Lower door into final position and tighten the screws (3)
Verify the hole’s assembly
With the drawer pulled out to full extension, insert the
lower basket (4) in the rail assembly.
4
3
WARNING: To prevent accidental child and pet entrapment or suffocation risk. DO NOT allow them to play inside of drawer.
WARNING: DO NOT step or sit down on Freezer Door.
14
REFRIGERATOR INSTALLATION
REMOVING, REVERSING AND REPLACING REFRIGERATOR DOORS (OPTIONAL)
NOTE: See the Parts and Features section
to match your model.
TOOLS NEEDED: 10mm hex-head socket wrench, No. 2 Phillips screwdriver, flat-head screwdriver, 10mm open-end wrench, flat 2-inch putty knife.
IMPORTANT: Before you begin, turn the refrigerator OFF and unplug it. Remove food and any adjustable door or utility bins from doors.
HOW TO REVERSE DOOR OPENING DIRECTION (when converting from the left-opening type to right­opening type)
1. Removing Refrigerator Door
Remove the top hinge cover (1). Remove the 3 screws and lift of f the top hinge (2). Lift the Refrigerator door (3) slightly and remove it. Pry off the cover (4) using a slotted screwdriver and
attach it on the right. Loosen the screw (5), remove the stoppers (6) and
attach them on the left (on the opposite side). Loosen the pin (7) and remove it. Lift off the washer (8). Pry off the cover (9) using a slotted screwdriver and
attach it on the right.
2. Removing Freezer Door
Lift the door (10) slightly and remove it. Loosen the 2 screws (11), the 2 screws (12), and lift
off the middle hinge (13). Take off the base grille (14). Remove the cap (15) and attach it on the right.
Loosen the 2 screws (16), remove the bottom hinge (17), and attach on the left.
Loosen the 2 screws (18) and attach the stopper (19) on the left side of the base.
3. Removing Refrigerator Handle
NOTE: To assist in installing the handle on the right
side, place a small piece of masking tape near the top of the handle before removing.
Grasp the handle tightly with both hands and slide the handle up (1)(this may require some force).
The keyhole slots (2) on the back of the handle allow the handle to separate from the mounting screws (3).
15
REFRIGERATOR INSTALLATION
Use an adjustable wrench to remove the handle mounting screws (3).
Carefully pry off the plug buttons (4).
Install the plug buttons (4) on left side. Install the handle mounting screw (3) on the right side Hold the handle so the masking tape is at the bottom. Align keyhole slots (2) on the top and bottom of the
back of the handle with the screws (3) mounted on the front of the door.
Press the handle against the door front, making sure that the screws (3) go into the keyhole slots (2).
Grasping the handle with both hands, press it firmly against the front of the door and slide the handle down (6). This may require some force.
4. Removing Freezer Handle
NOTE: Before start, check handle type in your model.
Handle Type 1
Remove the cap (1) and the 2 caps (2) using a slotted screwdriver.
Loosen the 2 screws (3), take of f the handle (4), and install it on the right.
Attach the caps you removed earlier [figures (1) and (2)].
Handle Type 2
For this handle type is not neccesary remove it.
5. Installing Freezer Door
Install the base grille (1).
Install the door (3) onto the bottom hinge pin.
Install the middle hinge (4) on the opposite side with the screw (5) and the screws (9).
6. Installing Refrigerator Door
Place the washer (6) on the middle hinge pin (7).
Install the door (8) so that it fits onto the middle hinge pin (7).
Install the top hinge (10) with screws.
Reinstall top hinge cover (11).
REFRIGERATOR INSTALLATION
AFTER COMPLETING THE JOB
Make sure that the four corners of the door gasket are not folded over. To ensure a good seal, apply a small
NOTE: Having someone push against the top of the refrigerator takes some weight off the leveling screws. This makes it easier to adjust the screws.
Open both doors again and check to make sure that
3.
they close easily. If not, tilt the refrigerator slightly more to the rear by turning both leveling screws clockwise. It may take several more turns, and you should turn both leveling screws the same amount.
DOOR CLOSING AND ALIGNMENT
Door Closing
Your refrigerator has two front leveling screws one on the right and one on the left. If your refrigerator seems unsteady or you want the doors to close easier, adjust the refrigerator tilt using the instructions below:
1. Plug the refrigerator power cord into a 3-prong
grounded outlet. Move the refrigerator into its final position.
2. Use a screwdriver to adjust the leveling screws. Turn
the leveling screw clockwise to raise that side of the refrigerator or counterclockwise to lower it. It may take several turns of the leveling screw to adjust the tilt of the refrigerator.
4. Check, using a level.
5. Replace the base grille.
Door Alignment
If the space between your doors is uneven, follow the instructions below to align the doors:
1. Pry off the top hinge cover.
2. Loosen the top hinge screws using a 10 mm socket
or wrench.
3. Have someone hold the door in place or put a
spacer between the doors while you tighten the top hinge screws.
4. Replace the top hinge cover.
17
USING YOUR REFRIGERATOR
ENSURING PROPER AIR CIRCULATION
In order to ensure proper temperatures, air must flow between the refrigerator and freezer sections. As shown in the illustration below, cool air enters through the bottom of the freezer section and moves up. Most of the air then flows through the freezer section vents and recirculates under the freezer floor. The rest of the air enters the refrigerator section through the top vent.
MULTI FLOW
The cooling fan operates more powerful and effective than in normal operation. This is specially noticeable when new food is placed in the refrigerator compartment.
If water or foreign substances enter the cool air vent while cleaning, efficiency will be lowered. In addition, if gasket is damaged, efficiency may be lowered because of escaping cool air.
SETTING THE CONTROLS
Your refrigerator has two controls that let you regulate the temperature in the freezer and refrigerator compartments.
Initially set the REFRIGERATOR CONTROL at 37°F (3°C) and the FREEZER CONTROL at 0°F ( -18°C). Leave it at this setting for 24 hours (one day) to stabilize. Then adjust the compartment temperature as desired.
Premium Model
(Identify your control type)
Refrigerator control: 32°F to 47°F (0°C to 8°C)
The lower the number setting, the colder the refrigerator compartment will become.
Freezer control: - 6°F to 9°F (- 21°C to - 13°C)
When the setting is at a lower number, the freezer compartment becomes colder. But the refrigerator compartment becomes warmer because less cold air flows into the refrigerator.
Do not block any of these vents with food packages. If the vents are blocked, airflow will be interrupted and temperature and moisture problems may occur.
IMPORTANT:
sections, any odors formed in one section will transfer to the other. You must thoroughly clean both sections to eliminate odors. To prevent odor transfer and drying out of food, wrap or cover foods tightly. (See the
Guide section for details.) DOOR ALARM
With this feature you´ll listen a alarm when the freezer or
refrigerator door is not closed within 1 minute after it is opened. These tones repeat every 30 seconds.
The alarm is cancelled when the freezer or the refrigerator
is closed correctly.
Because air circulates between both
Food Storage
Ice Plus:
Press the Ice Plus key and the LED will turn on. This function will remain activated for 24 hours and intensify the cooling speed of freezer and increase the amount of ice.
NOTE: To change °F/°C press and HOLD COLDER key co f freezer and COLDER key of refrigerator over 1 sec. at the same time.
18
USING YOUR REFRIGERATOR
Middle Models
(Identifier your control type)
Refrigerator control: position 1 to 7
(32°F to 47°F or 0°C to 8°C)
The higher the number setting, the colder the refrigerator compartment will become.
REFRIGERATOR TEMP
ADJUST
WARMER
4 IS RECOMMENDED
Freezer control: position 1 to 7
(-6°F to 8°F or -21°C to -13°C)
When the setting is at a higher number, the freezer compartment becomes colder. But the refrigerator compartment becomes warmer because less cold air flows into the refrigerator.
Ice Plus
Press the Ice Plus key and the LED will turn on. This function will remain activated for 24 hours and intensify the cooling speed of freezer and increase the amount of ice.
FREEZER TEMP
WARMER
4 IS RECOMMENDED
COLDER
ADJUST
RECOMMENDED
CONDITION/REASON: ADJUSTMENT: REFRIGERATOR section Turn
too warm REFRIGERATOR
Door opened often control to next Large amount of food added higher number, Room temperature very warm wait 24 hours,
then re-check
FREEZER section too warm/ Turn FREEZER ice not made fast enough control to next
Door opened often higher number, Large amount of food added wait 24 hours, Very cold room temperature Then re-check (can’t cycle often enough) Heavy ice usage Air vents blocked by items Move items out of
airstream
REFRIGERATOR section too Turn cold REFRIGERATOR
Controls not set correctly for control to next your conditions lower number,
wait 24 hours,
then re-check
FREEZER section too cold Turn FREEZER
Controls not set correctly for control to next your conditions lower number,
wait 24 hours, then re-check
ADJUSTING CONTROL SETTINGS
Give the refrigerator time to cool down completely before adding food. It is best to wait 24 hours before you put food into the refrigerator. The mid-settings indicated in the previous section should be correct for normal household refrigerator usage. The controls are set correctly when milk or juice is as cold as you like and when ice cream is firm.
The refrigerator control functions as the thermostat for the entire appliance (refrigerator and freezer sections.) The higher the number setting, the longer the compressor will run to keep the temperature colder. The freezer control adjusts the cold air flow from the freezer to the refrigerator. Setting the freezer control to a lower temperature keeps more cold air in the Freezer compartment to make it colder.
If you need to adjust temperatures in the refrigerator or freezer, start by adjusting the refrigerator first. Wait 24 hours after the refrigerator adjustment to check the freezer temperature. If it is too warm or too cold, then adjust the freezer control as well.
Use the settings listed in the chart below as a guide.
Always remember to wait at least 24 hours between adjustments.
19
USING YOUR REFRIGERATOR
FOOD STORAGE GUIDE
Storing Fresh Food
Wrap or store food in the refrigerator in airtight and moisture-proof material unless otherwise noted. This prevents food odor and taste transfer throughout the refrigerator. For dated products, check date code to ensure freshness.
Butter or margarine
Keep opened butter in a covered dish or closed compartment. When storing an extra supply, wrap in freezer packaging and freeze.
Cheese
Store in the original wrapping until you are ready to use it. Once opened, rewrap tightly in plastic wrap or aluminum foil.
Milk
Wipe milk cartons. For best storage, place milk on interior shelf, not on door shelf.
Eggs
Store in original carton on interior shelf, not on door shelf.
Fruit
Wash, let dry, and store in refrigerator in plastic bags or in the crisper. Do not wash or hull berries until you are ready to use them. Sort and keep berries in their original container in a crisper, or store in a loosely closed paper bag on a refrigerator shelf.
Leafy vegetables
Remove store wrapping and trim or tear off bruised and discolored areas. Wash in cold water and drain. Place in a plastic bag or plastic container and store in the crisper.
Vegetables with skins (carrots, peppers)
Place in plastic bags or plastic container and store in crisper.
Fish
Use fresh fish and shellfish the same day purchased.
Chef fresh
Store most chef fresh in original wrapping as long as it is airtight and moisture-proof. Rewrap if necessary.
Packaging
Successful freezing depends on correct packaging. When you close and seal the package, it must not allow air or moisture in or out. If you do, you could have food odor and taste transfer throughout the refrigerator and also dry out frozen food.
Packaging recommendations:
Rigid plastic containers with tight-fitting lids Straight-sided canning/freezing jars Heavy-duty aluminum foil Plastic-coated paper Non-permeable plastic wraps Specified freezer-grade self-sealing plastic bags
Follow package or container instructions for proper freezing methods.
Do not use:
Bread wrappers Non-polyethylene plastic containers Containers without tight lids Wax paper or wax-coated freezer wrap Thin, semi-permeable wrap
Freezing
IMPORTANT: Do not store bottles in the freezer
compartment - they may break when frozen, causing damage.
Your freezer will not quick-freeze any large quantity of food. Do not put more unfrozen food into the freezer than will freeze within 24 hours (no more than 2 to 3 lbs of food per cubic foot of freezer space). Leave enough space in the freezer for air to circulate around packages. Be careful to leave enough room at the front so the door can close tightly.
Storage times will vary according to the quality and type of food, the type of packaging or wrap used (airtight and moisture-proof) and the storage temperature. Ice crystals inside a sealed package are normal. This simply means that moisture in the food and air inside the package have condensed, creating ice crystals.
NOTE: Allow hot foods to cool at room temperature for 30 minutes, then package and freeze. Cooling hot foods before freezing saves energy.
NOTE: Do not store food near the sensor; it may cause the sensor to malfunction.
Leftovers
Cover leftovers with plastic wrap or aluminum foil. Plastic containers with tight lids can also be used.
STORING FROZEN FOOD
NOTE: For further information about preparing food for
freezing or food storage times, check a freezer guide or a reliable cookbook.
WARNING
Suffocation Hazard
When using dry ice, provide adequate ventilation. Dry ice is frozen carbon dioxide vaporizes, it can displace oxygen, causing dizziness, light-headedness, unconsciousness and death by suffocation. Open a window and do not breathe the vapors.
20
(CO )2. When it
USING YOUR REFRIGERATOR
REFRIGERATOR SHELVES
The shelves in your refrigerator are adjustable to meet your individual storage needs. These units are all glass shelves.
Storing similar food items together in your refrigerator and adjusting the shelves to fit different heights of items will make finding the exact item you want easier; it will also reduce the amount of time the refrigerator door is open, saving energy.
IMPORTANT: Do not clean glass shelves with warm water when they are cold. Shelves may break if exposed to sudden temperature changes or impact, such as bumping. For your protection, glass shelves are made with tempered glass, which will shatter into small pebble­sized pieces.
NOTE: Glass shelves are heavy. Use special care when removing them to avoid dropping them.
Adjusting Shelves
Remove shelves from the shipping position and replace shelves in the position you want.
To remove a shelf:Tilt up the front of the shelf in the
direction of (1) and lift it in the direction of (2). Pull the shelf out.
Sliding Out Shelves (optional on some models)
You can slide some glass shelves in and out of your refrigerator as follows.
To slide the shelf out, carefully pull front of shelf toward you.
To slide shelf in, push shelf in until it stops.
To remove a sliding shelf from its metal frame:
1. Pull the shelf out to the stop position.
2. Tilt the front of the shelf up and pull it past the stop position.
3. Lift up the shelf to remove. Replace the shelf by reversing the above steps. Convenience Shelves (optional on some models)
Folding Shelf: You can store taller items such as gallon
containers or bottles by simply sliding the shelf back.
To replace a shelf : Tilt the front of the shelf up and guide the shelf hooks into the slots at a desired height. Then lower the front of the shelf so that the hooks drop into the slots.
NOTE: Make sure that shelves are level from one side to the other. Failure to do so may result in the shelf falling or spilling food.
21
Loading...
+ 47 hidden pages