LG LP-154WP2-TLA3 Service manual

LP154WP2

Liquid Crystal Display

Product Specification

SPECIFICATION

FOR

APPROVAL

)

(

(

Preliminary Specification

●

)

Final Specification

15.4” WXGA+ TFT LCDTitle

AppleBUYER

MODEL

*When you obtain standard approval,

www.jxlcd.com

www.jxlcd.com

APPROVED BY

/

/

/

SIGNATURE

please use the above model name without suffix

APPROVED BY SIGNATURE

REVIEWED BY

PREPARED BY

LG.Philips LCD Co., Ltd.SUPPLIER

LP154WP2*MODEL

TLA3Suffix

Please return 1 copy for your confirmation with
your signature and comments.

Ver. 0.0 05, Nov, 2007

Product Engineering Dept.

LG. Philips LCD Co., Ltd

0/ 27

Product Specification

Contents

LP154WP2

Liquid Crystal Display

ITEMNo

COVER

CONTENTS

RECORD OF REVISIONS

GENERAL DESCRIPTION1

ABSOLUTE MAXIMUM RATINGS2

ELECTRICAL SPECIFICATIONS3

ELECTRICAL CHARACTREISTICS3-1

INTERFACE CONNECTIONS3-2

SIGNAL TIMING SPECIFICATIONS3-3

SIGNAL TIMING WAVEFORMS3-4

COLOR INPUT DATA REFERNECE3-5

www.jxlcd.com

www.jxlcd.com

POWER SEQUENCE3-6

OPTICAL SFECIFICATIONS4

MECHANICAL CHARACTERISTICS5

Page

1

2

3

4

5

6

7

9

9

10

11

12

16

RELIABLITY6

INTERNATIONAL STANDARDS7

SAFETY7-1

EMC7-2

PACKING8

DESIGNATION OF LOT MARK8-1

PACKING FORM8-2

PRECAUTIONS9

APPENDIX A. Enhanced Extended Display Identification DataA

Ver. 0.0 05, Nov, 2007

20

21

21

22

22

23

25

1/ 27

Product Specification

RECORD OF REVISIONS

LP154WP2

Liquid Crystal Display

DescriptionPageRevision DateRevision No

First Draft-05. Nov. 20070.0

www.jxlcd.com

www.jxlcd.com

EDID

ver

V0.0

Ver. 0.0 05, Nov, 2007

2/ 27

LP154WP2

Liquid Crystal Display

Product Specification

1. General Description

The LP154WP2 is a Color Active Matrix Liquid Crystal Display with an integral LED backlight system. The
matrix employs a-Si Thin Film Transistor as the active element. It is a transmissive type display operating in
the normally white mode. This TFT-LCD has 15.4 inches diagonally measured active display area with
WXGA+ resolution(1440 horizontal by 900 vertical pixel array). Each pixel is divided into Red, Green and
Blue sub-pixels or dots which are arranged in vertical stripes. Gray scale or the brightness of the sub-pixel
color is determined with a 6-bit gray scale signal for each dot, thus, presenting a palette of more than
262,144 colors.

The LP154WP2 has been designed to apply the interface method that enables low power, high speed, low
EMI.

The LP154WP2 is intended to support applications where thin thickness, low power are critical factors and
graphic displays are important. In combination with the vertical arrangement of the sub-pixels, the
LP154WP2 characteristics provide an excellent flat display for office automation products such as Notebook
PC.

CN

1

User connector

www.jxlcd.com

www.jxlcd.com

40

Pin

General Features

LVDS &

(LOG_B type)

(LOG_B type)

Timing

Control

Block

POWER

BLOCK

EDID

BLOCK

Control & Data Power EDID signal & Power

15.4 inches diagonal Active Screen Size

344.0 (H) × 222.0 (V) × 5.8(D, Typ.) mmOutline Dimension

0.2301 mm × 0.2301 mm Pixel Pitch

1440 horiz. by 900 vert. Pixels RGB strip arrangementPixel Format

6-bit, 262,144 colorsColor Depth

330 cd/m2(Typ., @I

Total 4. 57 Watt @ LCM circuit 1.15 Watt(Typ.full black), B/L 3.42 Watt(Max.)Power Consumption

440g (Typ.), 455(Max.)Weight

Transmissive mode, normally whiteDisplay Operating Mode

Hard coating(2H) Anti-glare treatment of the front Polarizer (Haze 44%)Surface Treatment

LED

=19mA) , 160 points Average Luminance, White

TFT-LCD Panel

(1440 x 900)

Source Driver Circuit

LED Backlight Ass’y

10LEDs X 6 strings

(LOG_B type)(LOG_B type)

1440

1

Gate Driver

9001

Ver. 0.0 05, Nov, 2007

3/ 27

LP154WP2

Liquid Crystal Display

Product Specification

2. Absolute Maximum Ratings

The following are maximum values which, if exceeded, may cause faulty operation or damage to the unit.

Table 1. ABSOLUTE MAXIMUM RATINGS

60

Values

Units

MaxMin

90% 80%

60%

Humidity[(%)RH]

Storage

40%

Operation

20%

10%

Parameter Notes

Power Input Voltage

Operating Temperature

Storage Temperature

Operating Ambient Humidity

Storage Humidity

Note : 1. Temperature and relative humidity range are shown in the figure below.

Wet bulb temperature should be 39°C Max, and no condensation of water.

www.jxlcd.com

www.jxlcd.com

Wet Bulb
Temperature [℃℃℃℃]

20

10

0

Symbol

50

40

30

at 25 ± 5°CVdc4.0-0.3VCC

1°C500TOP

1°C60-20HST

1%RH9010HOP

1%RH9010HST

-20

Ver. 0.0 05, Nov, 2007

10

20 30 40 50

Dry Bulb Temperature [℃℃℃℃]

60 70 800

4/ 27

LP154WP2

Liquid Crystal Display

Product Specification

3. Electrical Specifications

3-1. Electrical Characteristics

The LP154WP2 requires two power inputs. One is employed to power the LCD electronics and to drive the

TFT array and liquid crystal. The second input which powers the LED BL.

Table 2. ELECTRICAL CHARACTERISTICS

Parameter Symbol

MODULE :

Power Supply Input Current

Differential Impedance

LED Backlight :

Operating Voltage

Operating Current per string

Power Consumption

CC

Zm

LED

LED

BL

Values

MaxTypMin

3.63.33.0VCCPower Supply Input Voltage

V

NotesUnit

DC

1mA400348-I

1Watt1.321.15-PcPower Consumption

2Ohm11010090

3V3330-V

4mA-19-I

5Watt3.773.42-P

6Hrs--10,000Life Time

Note)

1. The specified current and power consumption are under the Vcc = 3.3V , 25℃, fv = 60Hz condition

whereas full black pattern is displayed and fv is the frame frequency.

2. This impedance value is needed to proper display and measured form LVDS Tx to the mating connector.

3. The variance of the voltage is ± 10%.

4. The typical operating current is for the typical surface luminance (LWH) in optical characteristics.

I

LED

5. The LED power consumption shown above does not include power of external LED driver circuit
for typical current condition.

6. The life time is determined as the time at which brightness of LED is 50% compare to that of initial value
at the typical LED current.

www.jxlcd.com

www.jxlcd.com

is the current of each LEDs’ string, LED backlight has 6 strings on it.

Ver. 0.0 05, Nov, 2007

5/ 27

LP154WP2

Liquid Crystal Display

Product Specification

3-2. Interface Connections

This LCD employs two interface connections, a 40 pin connector is used for the module electronics interface
and the other connector is used for the integral backlight system.

The electronics interface connector is a model FI-JH-40S manufactured by JAE.

Table 3. MODULE CONNECTOR PIN CONFIGURATION (CN1)

NotesDescriptionSymbolPin

[LVDS Receiver]

GroundGND1

Power Supply, 3.3V Typ.VCC2

Power Supply, 3.3V Typ.VCC3

DDC 3.3V powerV EDID4

Power Supply, 3.3V Typ.VCC5

DDC ClockCLK EDID6

DDC DataDATA EDID7

Negative LVDS differential data inputRA1-8

Positive LVDS differential data inputRA1+9

GND

www.jxlcd.com

www.jxlcd.com

Ground10

Negative LVDS differential data inputRB1-11

Positive LVDS differential data inputRB1+12

GroundGND13

Negative LVDS differential data inputRC1-14

Positive LVDS differential data inputRC1+15

GroundGND16

Negative LVDS differential clock inputRCLK1-17

Positive LVDS differential clock inputRCLK1+18

GroundGND19

Negative LVDS differential data inputRA2-20

Positive LVDS differential data inputRA2+21

GroundGND22

Negative LVDS differential data inputRB2-23

Positive LVDS differential data inputRB2+24

GroundGND25

Negative LVDS differential data inputRC2-26

Positive LVDS differential data inputRC2+27

GroundGND28

Negative LVDS differential clock inputRCLK2-29

[LVDS Receiver]

[LVDS Receiver][LVDS Receiver]

SW, (LVD4107x) X 2

[Connector]

[Connector]

[Connector][Connector]

JAE FI-JT-40S-HF10 or equivalent (1.0

mm thickness, lock-in type, pin 1

starts from left on the front)

[Mating Connector]

[Mating Connector]

[Mating Connector][Mating Connector]

JAE FI-JT-40C series or equivalent

(micro-coax type)

[Connector pin arrangement]

[Connector pin arrangement]

[Connector pin arrangement][Connector pin arrangement]

LCD rear view

1

40

Ver. 0.0 05, Nov, 2007

6/ 27

LP154WP2

Liquid Crystal Display

Product Specification

Positive LVDS differential clock inputRCLK2+30

LED Cathode (Negative)Vdc131

LED Cathode (Negative)Vdc232

LED Cathode (Negative)Vdc333

LED Cathode (Negative)Vdc434

LED Cathode (Negative)Vdc535

LED Cathode (Negative)Vdc636

No ConnectionNC37

LED Anode(Positive)Vdc(1,2,3,4,5,6)38

LED Anode(Positive)Vdc(1,2,3,4,5,6)39

LED Anode(Positive)Vdc(1,2,3,4,5,6)40

The LED backlight connector is a model TF12-9S-0.5H, manufactured by Hirose.

Table 4. BACKLIGHT CONNECTOR PIN CONFIGURATION (CN2)

www.jxlcd.com

www.jxlcd.com

1

2

3

4

5

6

7

8

9

Vdc(1,2,3,4,5,6)

Vdc(1,2,3,4,5,6)

Vdc1

Vdc2

Vdc3

Vdc4

Vdc5

Vdc6

LED Anode(Positive)

LED Anode(Positive)

No ConnectionNC

LED Cathode (Negative)

LED Cathode (Negative)

LED Cathode (Negative)

LED Cathode (Negative)

LED Cathode (Negative)

LED Cathode (Negative)

NotesDescriptionSymbolPin

9 1

Ver. 0.0 05, Nov, 2007

7/ 27

LP154WP2

Liquid Crystal Display

Product Specification

3-3. Signal Timing Specifications

This is the signal timing required at the input of the User connector. All of the interface signal timing should be
satisfied with the following specifications and specifications of LVDS Tx/Rx for its proper operation.

Table 5. TIMING TABLE

Note

ITEM

ITEMITEM

SymbolITEM

SymbolSymbol

Min.Symbol

Min.Min.

Typ.Min.

Typ.Typ.

Max.Typ.

Max.Max.

UnitMax.

UnitUnit

NoteUnit

NoteNote

FrequencyDCLK

Hsync

Vsync

Data

Enable

Active

Period

Width-Active

Active

Period

Width-Active

Horizontal back
porch

Horizontal front
porch

Vertical back
porch

www.jxlcd.com

www.jxlcd.com

Vertical front
porch

3-4. Signal Timing Waveforms

t

t

t

t

CLK

HA

HP

WH

VA

VP

WV

HBP

HFP

VBP

VFP

1440tw

1648t

900tw

905t

176

16t

16

MHz103.296.8289.48f

1440

1752

32

900

923

1t

3

1

3

220

60

17

3

1440

1872

48

900

923

3

272

112

17

3

tCLK

tCLK

Condition : VCC=3.3V

tHP

tHP

High: 0.7VCC

Low: 0.3VCC

t

Hsync

Date Enable

Vsync

Ver. 0.0 05, Nov, 2007

t

WH

t

WV

Date Enable

t

VBP

t

HBP

HP

t

tWHA

VP

tWVA

t

HFP

t

VFP

8/ 27