DATE: ‘07.03.05
www.DataSheet.net/
Datasheet pdf - http://www.DataSheet4U.co.kr/
Specification Rev. 1.0
Specification of 14.1” TFT/LCD
MODEL: LP141WP1 (TLD2)
1/ 57
ApprovedCheckedPrepared
www.jxlcd.com
www.jxlcd.com
I.Y. Jung
/Eng. Dept.
/Engineer
NOTICE of RECEIPT
We accepted this specification. OME Operations, TOSHIBA Corp.
Purchasing
Dept.
PC
Hardware
Dept.
G.J. Han
/Eng. Dept.
/Manager
S.C. Yun
/Eng. Dept.
/Senior Mgr
S.P. Yang
/QA. Dept.
/Senior Mgr
Senr. MgrSenr. Eng.Eng.
Senr. MgrSenr. Eng.Eng.
LG.Philips LCD.,Co.Ltd
PDF created with pdfFactory Pro trial version www.pdffactory.com
Date: 2007.03.06
Specification Rev. 1.0
www.DataSheet.net/
Datasheet pdf - http://www.DataSheet4U.co.kr/
-CONTENTS -
Record of Revision ---------------------------------------------------------------3
1. Scope ---------------------------------------------------------------4
2. General Specifications ---------------------------------------------------------------4
2.1. Features
2.2.Dimensional Outline
3. Absolute Maximum Ratings ---------------------------------------------------------------9
3.1. Absolute Ratings of Environment
3.2. Electrical Absolute Maximum
3.3. Mechanical ratings
3.4. The others
4. Optical Characteristics ---------------------------------------------------------------16
4.1 Test Conditions
4.2 Optical Specifications
5. Electrical Characteristics ---------------------------------------------------------------21
5.1. TFT LCD module
5.2. Backlight Unit
5.3. Regulation
6.Block Diagram ---------------------------------------------------------------27
7. Input Terminal Pin Assignment ---------------------------------------------------------------28
7.1 TFT LCD module
7.2 Backlight Unit
7.3 LVDS Transmitter
7.4 Timing Diagrams of LVDS for Transmission
7.5 Input Signal, Basic Display Colors and Gray Scale of Each Colors
8.Interface timing ---------------------------------------------------------------33
8.1 Timing Parameters
8.2 Timing diagrams of interface signal
8.3 Power On / Off Sequence
9.Cosmetic Specification ---------------------------------------------------------------35
9.1 Sampling
9.2 Conditions of Inspections
9.3 Defect modes
9.4 Mechanical inspection
9.5 Visual Inspection
9.6 Electrical inspection
10. Packing ---------------------------------------------------------------39
11.Labels and Lamp Ass’y Exchange ---------------------------------------------------------------41
12. General Precaution ---------------------------------------------------------------53
www.jxlcd.com
www.jxlcd.com
2/ 57
Appendix ---------------------------------------------------------------55
LG.Philips LCD.,Co.Ltd
PDF created with pdfFactory Pro trial version www.pdffactory.com
Date: 2007.03.06
Record of Revision
www.DataSheet.net/
Datasheet pdf - http://www.DataSheet4U.co.kr/
‘07. 02.01
43, 45, 52
Specification Rev. 1.0
EDID55~57
3/ 57
ReasonNewOldItemSheet(New)Rev. No.Date
First EditionAll0.0’06. 11. 27
Max. 450Max. 435gWeight40.1‘07. 01. 22
--Drawing5, 6, 7, 8, 25,
Normal B/L
Typ. 170 nitTyp. 200 nitLuminance16
Max. 1.6Max. 2.0White Var.
--Backlight repair parts43
Toshiba requestCheck sum : 4ECheck sum :
4C
Corrected an errorAnti-glareGlareSurface treatment40.2
UpdatedTiming parameters330.3’07. 02.07
Toshiba request
Ver. 0.2Ver. 0.1EDID (Timing)55~57
71.0’07. 03. 06
37
www.jxlcd.com
www.jxlcd.com
Gap Between Upper
polarizer and Case Top
Dot Inspection
Updated
Toshiba request
Added
LG.Philips LCD.,Co.Ltd
PDF created with pdfFactory Pro trial version www.pdffactory.com
Date: 2007.03.06
Specification Rev. 1.0
www.DataSheet.net/
Datasheet pdf - http://www.DataSheet4U.co.kr/
1. Scope
This specification is applicable to LCD manufacturer’s 35.81cm (14.1”) diagonal size TFT-LCD module
"LP141WP1(TLD2)" designed for Personal Computer.
2. General Specification
2.1. Features
SpecificationsItem
303.69(W) × 189.81(H) (mm) ( 14.1 ” diagonal)Display area ( Active area)
TFT active matrixDriving Method
Number of Pixels
Pixel pitch
Pixel Arrangement
Surface Treatment
Dimensional Outline
www.jxlcd.com
www.jxlcd.com
1440(W) × 900(H) × R,G,B (WXGA+) (pixels)
0.2109(H) × 0.2109(V) (mm)
RGB vertical stripes
262,144 (colors)Display color
Transmissivetype, Normally whiteDisplay Mode
6 o'clock (in direction of maximum contrast)Viewing Direction
Anti-glare treatment of the front polarizer
LVDS2PortInterface
cold-cathode fluorescent lamp for side lightingBacklight
320 (H) × 206(V) × 5.5(D) mm (Max.)
306.76 (W) × 193(H) (mm)Bezel Opening
450g(Max.)Weight
1)
1)
1)
4/ 57
Note 1)
1 2 1399 1440
1
2
899
900
LG.Philips LCD.,Co.Ltd
BGRBGRBGRBGR
BGRBGRBGRBGR
BGRBGRBGRBGR
BGRBGRBGRBGR
0.2109mm
BGR
: Pixel
R G B
0.2109mm
Date: 2007.03.06
: Sub-pixel
(Dots)
PDF created with pdfFactory Pro trial version www.pdffactory.com
2.2. Dimensional Outline
www.DataSheet.net/
Datasheet pdf - http://www.DataSheet4U.co.kr/
( Front figure )
Specification Rev. 1.0
5/ 57
www.jxlcd.com
www.jxlcd.com
LG.Philips LCD.,Co.Ltd
Date: 2007.03.06
PDF created with pdfFactory Pro trial version www.pdffactory.com
( Back figure )
www.DataSheet.net/
Datasheet pdf - http://www.DataSheet4U.co.kr/
Specification Rev. 1.0
6/ 57
www.jxlcd.com
www.jxlcd.com
LG.Philips LCD.,Co.Ltd
Date: 2007.03.06
PDF created with pdfFactory Pro trial version www.pdffactory.com
Specification Rev. 1.0
www.DataSheet.net/
Datasheet pdf - http://www.DataSheet4U.co.kr/
(Detail description of side mounting screw )
7/ 57
www.jxlcd.com
www.jxlcd.com
LG.Philips LCD.,Co.Ltd
Date: 2007.03.06
PDF created with pdfFactory Pro trial version www.pdffactory.com
Specification Rev. 1.0
www.DataSheet.net/
Datasheet pdf - http://www.DataSheet4U.co.kr/
(Detail description of height of LCM back side & TABZone)
8/ 57
www.jxlcd.com
www.jxlcd.com
LG.Philips LCD.,Co.Ltd
Date: 2007.03.06
PDF created with pdfFactory Pro trial version www.pdffactory.com
Specification Rev. 1.0
www.DataSheet.net/
Datasheet pdf - http://www.DataSheet4U.co.kr/
3. Absolute Maximum Ratings
3.1. Absolute Ratings of Environment
9/ 57
MaxMinItem NoteSymbol
Operating Ambient Temperature
Operating Temperature for Panel
Storage Temperature
Operating Ambient Humidity
Storage Humidity
Air Pressure
Air Pressure
Altitude
Altitude
Note 1) Temperature and relative humidity range are shown in the figure below.
Wet bulb temperature should be 39°C Max, and no condensation of water.
www.jxlcd.com
www.jxlcd.com
Wet Bulb
Temperature [
30
20
10
0
-
-
90%80%
60
]
C
°
50
40
60%
Unit
Humidity[(%)RH]
40%
20%
10%
(1)°C+500TOP
(2)°C+600-
(1)°C+65-20TSTG
(1)%RH9010HOP
(1)%RH9010HSTG
OperationkPa101.357-
Non-operationkPa101.312-
OperationKm3-
Non-operationKm12-
Storage
Operation
-20
Note 2) The surface temperature caused by self heat radiation of cell itself is specified on this item.
10
20 30 40 50
Dry Bulb Temperature [℃]
60 70 800
LG.Philips LCD.,Co.Ltd
PDF created with pdfFactory Pro trial version www.pdffactory.com
Date: 2007.03.06
3.2. Electrical Absolute Maximum
www.DataSheet.net/
Datasheet pdf - http://www.DataSheet4U.co.kr/
(1) TFT LCD Module
Specification Rev. 1.0
10/ 57
Power Supply Voltage
Logic Input Voltage
(2) Back Light Unit
Lamp Voltage
Lamp Current
Lamp Frequency
www.jxlcd.com
www.jxlcd.com
MaxMinItem NoteSymbol
MaxMinItem NoteSymbol
Unit
at 25 ± 5°CV+4.0-0.3VDD
LVDS interfaceVVDD+0.3-0.3VIN
Unit
Broken lamp Max VoltageVRMS5000-VL
mARMS7.02.0IL
KHz8050FL
LG.Philips LCD.,Co.Ltd
PDF created with pdfFactory Pro trial version www.pdffactory.com
Date: 2007.03.06
3.3. Mechanical Ratings
www.DataSheet.net/
Datasheet pdf - http://www.DataSheet4U.co.kr/
Test Item NoteTest Conditions
Frequency Range 5 -500 Hz, 14.7m/s21.5G) constant,
Mechanical Vibration
Mechanical Shock
LCD fix condition
-> See Note (2)
Pressure Resistance
-> See Note (1)
Strength of FL Cable
www.jxlcd.com
www.jxlcd.com
Connector tension test
at side-mount part
0.5Hrs each axis (X, Y, Z direction).
Frequency Range 5 -500 Hz, 4.9m/s2( 0.5G) constant,
0.5Hrs each axis (X, Y, Z direction).
No Destruction with the force 196 N (20 kgf, 16 mm in diameter) to
the display surface at the vertical direction.
No Destruction with the force 294.2 N (30 kgf, 30 mm in diameter)
to the back of the display surface at the vertical direction.
Only the breakage of below items will not happen after test.
( Glass.Lamp & Circuit parts)
Strength of
Rotation
force
Lead Pull
Test
Input connector : With 50 times of connector trial there must beno
damage to the shape and functionally.
Back light connector : With 50 times of connector trial there must be
no damage to the shape and functionally.
M2 : Max 2.5 kgf.cmAssured torque value
Specification Rev. 1.0
70G, Pulse width 11ms, Sine Wave ±X, ±Y, ±Z direction.
* Note) Normal function is only checking points.
Cable : No disconnection of cable to the 5 trial of
360 degree rotation. See a bended state of cable.
Connector : No disconnection of cable to 10 trial of
180 degree rotation. See a bended state of cable.
Soldering portion 29.4N(3.0kgf) 10mins
*1.08mm Wire applied
Connector : 12.9N (1.32kgf) 1 sec
*1.08mm Wire applied
11/ 57
Non Operation
Operation
Non Operation* 240G, Pulse width 2 ms, Sine Wave, ±X, ±Y, ±Z direction.
Operation98 m/s2 (10G), Pulse width 11 ms, Sine Wave, ±X, ±Y, ±Z direction.
Non Operation
Fig 1-1
Fig 1-2
Fig 1-3
Non Operation
FL cable
R2
Non Operation
Non Operation
Tapping area : All bezel(Metal cover) side,
Tapping test
Definitions of failure for judgment shall be as follows:
(1) Function of the module should be maintained.
(2) Current consumption should be smaller than the specified value.
(3) Appearance and display quality should not have distinguished degradation.
(4) Luminance should be larger than the minimum value specified in optical specification.
LCD: Full-screen gray (L32).
“Ripple (Pooling )” can not be seen in Active Area
Tapping Force: Max 3kgf.cm
LG.Philips LCD.,Co.Ltd
PDF created with pdfFactory Pro trial version www.pdffactory.com
Non Operation15 times under Max. torqueRe-screwed test
Operation
Date: 2007.03.06
Note 1)
www.DataSheet.net/
Datasheet pdf - http://www.DataSheet4U.co.kr/
Specification Rev. 1.0
(1) The compression condition of front side
(a) Compression point : 12 points ( refer to Fig 1-1)
(b) Compression condition: 20kgf, 3 sec, Tool diameter: 16 mm in diameter (refer to Fig 1-3)
:COMPRESSION POINT
LCDFlat plate
12/ 57
[ Fig 1-1 ]
(2) The compression condition of rear side
www.jxlcd.com
(a) Compression point : 21 points ( refer to Fig 1-2 )
www.jxlcd.com
(b)Compression condition : 30kgf, 3 sec, Tool radius: 30 mm in diameter ( refer to Fig 1-3)
:COMPRESSION POINT
ABS natural 2.0t
Flat plate
LCD
[ Fig 1-2 ]
LG.Philips LCD.,Co.Ltd
PDF created with pdfFactory Pro trial version www.pdffactory.com
Date: 2007.03.06
Specification Rev. 1.0
www.DataSheet.net/
Datasheet pdf - http://www.DataSheet4U.co.kr/
10mm in diameter
10
16
B
Rubber sheet
(3) Dimension of the compression jig
(a) compression jig for front side A = 16 mm in diameter
(b)compression jig for rear side A = 30 mm in diameter
www.jxlcd.com
www.jxlcd.com
A
[ Fig 1-3 ]
B = 16 mm in diameter
B = 28 mm in diameter
1.5
13/ 57
LG.Philips LCD.,Co.Ltd
PDF created with pdfFactory Pro trial version www.pdffactory.com
Date: 2007.03.06
Note 2) LCD fixing condition for z direction.
www.DataSheet.net/
Datasheet pdf - http://www.DataSheet4U.co.kr/
Z
Y X
Specification Rev. 1.0
14/ 57
www.jxlcd.com
www.jxlcd.com
LG.Philips LCD.,Co.Ltd
Date: 2007.03.06
PDF created with pdfFactory Pro trial version www.pdffactory.com
3.4. The Others
www.DataSheet.net/
Datasheet pdf - http://www.DataSheet4U.co.kr/
(1) Static electricity pressure resistance
(2) Sound noise
There should be no uncomfortable noise.
Being used under whatever surrounds, when power on/off, the panel should not generate
uncomfortable noise. And regarding specified values are negotiated if it is needed.
(3) Open / Short
No smoke, no fiery at any open/ short test
(4) MTBF : 50,000 Hr (except for backlight lamp)
Specification Rev. 1.0
15/ 57
Non OperationOperationItem Testing conditions
± 10kV±8KV150pF, 330 ohmContact discharge
±20 KV±15KV 150pF, 330 ohmAir discharge
www.jxlcd.com
www.jxlcd.com
LG.Philips LCD.,Co.Ltd
Date: 2007.03.06
PDF created with pdfFactory Pro trial version www.pdffactory.com
Specification Rev. 1.0
www.DataSheet.net/
Datasheet pdf - http://www.DataSheet4U.co.kr/
16/ 57
4. Optical Characteristics
4.1. Test Conditions
Ambient Temperature : T
Ambient Humidity : H
Supply Voltage : V
a
DD
Input Signal : According to typical value in "Electrical Characteristics"
FL Input Current : IL= 6.0mA
FL Driving Frequency : fLF= ( 60±5 kHz )
FL Inverter : FIF1311-06A (PRONTEK Rev1.0)
The measuring method is shown in following 4.2. The items are measured under stable conditions. The
optical characteristics should be measured in a dark room ( Screen illuminance< 2lx ) or equivalent state
with the methods shown in Note (6).
25±5°C
a
65±20%RH
3.3V
RMS
4.2. Optical Specifications
NoteUnitMax.Typ.Min.ConditionsSymbolItem
Contrast Ratio
(Center 1 Point)
Average luminance
Cross Modulation
Luminance
Uniformity
Chromaticity
Viewing
Angle
13 Points CR Variation
www.jxlcd.com
www.jxlcd.com
Red
Green
Blue
White
Hor.
Ver.
Hor.
Ver.
CR
Rx
Ry
Gx
Gy
Bx
By
Wx
Wy
θ
θ
θ
θ
δW13 Points White Variation
SHA
θ
θ
Low
θ
θ
Low
L
θ=0°, φ=0°
Viewing
normal angle
L
R
CR>=10
up
L
R
CR>=5
up
R
φ = 180
φ = 0°
φ = 90°
φ = -90°
φ = 180
φ = 0°
φ = 90°
φ = -90°
θ=0°, φ=0°
Viewing
normal angle
0.558
0.316
0.298
0.519
0.127
0.112
0.283
0.299
40
40
15
30
45
45
20
35
0.588
0.346
0.328
0.549
0.157
0.142
0.313
0.329
45
45
20
35
50
50
25
40
-170140Y
0.618
0.376
0.358
0.579
0.187
0.172
0.343
0.359
-
-
-
-
-
-
-
-
-
deg.
2
cd/m
(2), (6)--350250
(3)ms2516-Tr+ TfResponse Time
*IFL=6.0mA
FL=60±5kHz
Gray Scale Level
(Color Coordinate of
the R,G,B is based
on LPL’s equipment,
and Color Coordinate
of the W is based on
Toshiba’s equipment)
RMS
= L63 (White)
(5)%2.0--D
(1), (6)
PR650
Only for
Color
Coordinate
(7)1.61.4-
(7), A1.6--δC
(8)1.6--dLWhite Variation
LG.Philips LCD.,Co.Ltd
PDF created with pdfFactory Pro trial version www.pdffactory.com
Date: 2007.03.06
Specification Rev. 1.0
www.DataSheet.net/
Datasheet pdf - http://www.DataSheet4U.co.kr/
Attach the Lamp current – Luminance characteristics. The range of lamp current is shown in 3.2 (2)
A. Present CR Variation(13Points) Spec is based on PR-880 Equipment and can be changed by the
measuring equipment.
63
θ=0°, φ=0°
Normalized luminance
at each gray level
At normal viewing direction, during displaying the L0-L63 gray scale bar, luminance intensity inversion
can not be seen.
Viewing
normal angle
100100100
92.1 80.5 65.4 55
74.3 58.9 43.7 47
56.4 39.2 27.6 39
38.40 23.57 14.70 31
21.40 11.89 6.80 23
9.30 4.17 2.40 15
3.78 0.67 0.33 7
0.70 0.17 0.01 0
%
(1), (6)
(Center 1 Point)
17/ 57
NoteUnitMax.Typ.Min.ConditionsGray levelItem
Note 1) Definition of viewing angle θ and φ
www.jxlcd.com
www.jxlcd.com
φ
= 180
Note 2) LCD fixing condition for z direction.
The contrast ratio can be calculated by the following expression.
Contrast Ratio (CR) = L63 / L0
L63 : Luminance on the white raster (gray scale level L63)
L 0 : Luminance on the black raster (gray scale level L0)
°
φ
= 270
Left
,
,
°
Down
Normal
θ
Measurement
Direction
φ
Y
φ
= 90°, Up
φ
°
= 0
,
Right
LG.Philips LCD.,Co.Ltd
PDF created with pdfFactory Pro trial version www.pdffactory.com
Date: 2007.03.06
Note 3) Definition of response time
www.DataSheet.net/
Datasheet pdf - http://www.DataSheet4U.co.kr/
Specification Rev. 1.0
18/ 57
SHA
Tr
)
%
100
90
Optical
Response
10
0
Bright Bright
Note 4) Definition of surfaceluminance of white
Measure the luminance of white at Centerpoint. Surfaceluminance of white Y
Note 5) Definition of Cross Modulation (D
D
= | YB– YA| / YA×100 (%)
www.jxlcd.com
SHA
www.jxlcd.com
Tf
Dark
L
Where:
YA= Luminance of measured location without darkest gray pattern (cd/m2)
YB= Luminance of measured location with darkest gray pattern (cd/m2)
(0, 0)
Gray Level 42
VIEW AREA
LG.Philips LCD.,Co.Ltd
YA(500, 225)
(1439, 899)
Gray Level 0
Gray Level 42
(0, 0)
VIEW AREA
(100, 100)
YA(500, 225)
(250, 350)
(1439, 899)
Date: 2007.03.06
PDF created with pdfFactory Pro trial version www.pdffactory.com
Loading...