LG LP-133WX2-TLE1 Service manual

LP133WX2

Liquid Crystal Display

Product Specification

SPECIFICATION

FOR

APPROVAL

)

(
(

Preliminary Specification●

)

Final Specification

13.3” WXGA TFT LCDTitle

HPBUYER

MODEL

*When you obtain standard approval,

www.jxlcd.com

www.jxlcd.com

APPROVED BY

/

/

/

SIGNATURE

please use the above model name without suffix

APPROVED BY SIGNATURE

K. J. KWON / S.Manager

REVIEWED BY

S. W. Paeng / Manager

PREPARED BY

G. W. Do / Engineer

LP133WX2*MODEL
TLE1Suffix

LG.Philips LCD Co., Ltd.SUPPLIER

Please return 1 copy for your confirmation with
your signature and comments.

Ver. 0.5 29, Jul., 2008

Product Engineering Dept.

LG. Philips LCD Co., Ltd

0/ 25

Product Specification

Contents

LP133WX2

Liquid Crystal Display

ITEMNo

COVER
CONTENTS
RECORD OF REVISIONS
GENERAL DESCRIPTION1
ABSOLUTE MAXIMUM RATINGS2

ELECTRICAL SPECIFICATIONS3
ELECTRICAL CHARACTREISTICS 3-1

INTERFACE CONNECTIONS 3-2
SIGNAL TIMING SPECIFICATIONS 3-3
SIGNAL TIMING WAVEFORMS 3-4
COLOR INPUT DATA REFERNECE 3-5

www.jxlcd.com

www.jxlcd.com

POWER SEQUENCE 3-6
OPTICAL SFECIFICATIONS4
MECHANICAL CHARACTERISTICS5

Page

1
2
3
4

5
6
8
8

9
10
11
15

RELIABLITY6
INTERNATIONAL STANDARDS7
SAFETY 7-1
EMC 7-2
PACKING8
DESIGNATION OF LOT MARK 8-1
PACKING FORM 8-2
PRECAUTIONS9
APPENDIX A. Enhanced Extended Display Identification DataA

Ver. 0.5 29, Jul., 2008

18

19
19

20
20
21
23

1/ 25

Product Specification

RECORD OF REVISIONS

LP133WX2

Liquid Crystal Display

DescriptionPageRevision DateRevision No

First Draft-19. Mar. 20080.0

Timing spec update (Dclk 71Mhz  69.3Mhz)8
EDID update (Timing spec change)22,23,24

5, 1129.Jul.20080.5

www.jxlcd.com

www.jxlcd.com

Update spec.

-LED power consumption, Viewing angle

-Chromaticity, Gray scale

EDID

ver

-

- Module Connector Pin Configuration Update608.May.20080.1

- User Connector Configuration Image Update615.May.20080.2

0.2 LCM drawing Update15,163. Jun.,20080.3

0.3Optical spec update (life time, luminance, luminance variation)5,11,1220. Jun.20080.4

0.3

Ver. 0.5 29, Jul., 2008

2/ 25

LP133WX2

Liquid Crystal Display

Product Specification

1. General Description

The LP133WX2 is a Color Active Matrix Liquid Crystal Display with an integral LED backlight system. The
matrix employs a-Si Thin Film Transistor as the active element. It is a transmissive type display operating in
the normally white mode. This TFT-LCD has 13.3 inches diagonally measured active display area with
WXGA resolution(1280 horizontal by 800 vertical pixel array). Each pixel is divided into Red, Green and Blue
sub-pixels or dots which are arranged in vertical stripes. Gray scale or the brightness of the sub-pixel color is
determined with a 6-bit gray scale signal for each dot, thus, presenting a palette of more than 262,144
colors.
The LP133WX2 has been designed to apply the interface method that enables low power, high speed, low
EMI.
The LP133WX2 is intended to support applications where thin thickness, low power are critical factors and
graphic displays are important. In combination with the vertical arrangement of the sub-pixels, the
LP133WX2 characteristics provide an excellent flat display for office automation products such as Notebook
PC.

CN1 User connector 30 Pin

www.jxlcd.com

www.jxlcd.com

General Features

800

1

Gate Driver

(LOG_B type)

TFT-LCD Panel

1

Source Driver Circuit

LED Backlight Ass’y

9LEDs X 6 strings

= 19mA)Power Consumption

LED

LVDS &

Timing

Control

Block

POWE

R

BLOCK

EDID

BLOCK

Control & Data Power EDID signal & Power

13.3 inches diagonal Active Screen Size

296.0(H) × 203(V) × 3.5(D, Max.) mmOutline Dimension

0.2235 mm × 0.2235 mm Pixel Pitch
1280 horiz. by 800 vert. Pixels RGB strip arrangementPixel Format
6-bit, 262,144 colorsColor Depth
200 cd/m2(Typ., @I
Logic : 0.9 W (typ.@Mosaic), Back Light : 2.64W (typ.@ I
275g(Typ.), 290(Max.)Weight
Transmissive mode, normally whiteDisplay Operating Mode

Hard coating(3H), Glare treatment of the front Polarizer (Haze 0%)Surface Treatment

LED

=19mA)Luminance, White

(1280 x 800)

1280

Ver. 0.5 29, Jul., 2008

3/ 25

LP133WX2

Liquid Crystal Display

Product Specification

2. Absolute Maximum Ratings

The following are maximum values which, if exceeded, may cause faulty operation or damage to the unit.

Table 1. ABSOLUTE MAXIMUM RATINGS

Parameter Notes

Power Input Voltage
Operating Temperature
Storage Temperature
Operating Ambient Humidity
Storage Humidity

Note : 1. Temperature and relative humidity range are shown in the figure below.
Wet bulb temperature should be 39C Max, and no condensation of water.

www.jxlcd.com

www.jxlcd.com

Wet Bulb
Temperature [℃]

20

10

0

Symbol

60

50

40

30

Values

MaxMin

90% 80%

60%

40%

20%

10%

Units

Humidity[(%)RH]

Storage

Operation

at 25  5CVdc4.0-0.3VCC

1C500TOP
1C60-20HST
1%RH9010HOP
1%RH9010HST

-20

Ver. 0.5 29, Jul., 2008

10

20 30 40 50

Dry Bulb Temperature [℃]

60 70 800

4/ 25

LP133WX2

Liquid Crystal Display

Product Specification

3. Electrical Specifications
3-1. Electrical Characteristics

The LP133WX2 requires two power inputs. One is employed to power the LCD electronics and to drive the
TFT array and liquid crystal. The second input which powers the LED BL.

Table 2. ELECTRICAL CHARACTERISTICS

Parameter Symbol

MODULE :

Power Supply Input Current

Differential Impedance
LED Backlight :
Operating Current per string
Power Consumption

PWM Input Signal

www.jxlcd.com

www.jxlcd.com

LED Current

CC

Zm

LED

BL

Values

MaxTypMin

3.63.33.0VCC Power Supply Input Voltage

V

Hz215210206 Operating Frequency (for Reliability)

us50 On Time

mA-19- High State
mA-0- Low State

NotesUnit

DC

1mA313273230I
1Watt0.9Pc Power Consumption
2Ohm11010090

3mA19I
4Watt2.64-P
5Hrs--10,000 Life Time

6Hz1500200 Operating Frequency (for Operating)

7%1002 On Duty

V5 Maximum Voltage
V2.1 On threshold
V0.8 Off threshold

Note)

1. The specified current and power consumption are under the Vcc = 3.3V , 25℃, fv = 60Hz condition
whereas mosaic pattern is displayed and fv is the frame frequency.

2. This impedance value is needed to proper display and measured form LVDS Tx to the mating connector.

3. The typical operating current is for the typical surface luminance (LWH) in optical characteristics.
I

4. The LED power consumption shown above does not include power of external LED driver circuit
for typical current condition.

5. The life time is determined as the time at which brightness of LED is 50% compare to that of initial value
at the typical LED current.

6. LED Driver operating Frequency

7. There may be a flickering Under 6% dimming.

is the current of each LEDs’ string, LED backlight has 6 strings on it.

LED

Ver. 0.5 29, Jul., 2008

5/ 25

LP133WX2

Liquid Crystal Display

Product Specification

3-2. Interface Connections

This LCD employs two interface connections, a 40 pin connector is used for the module electronics interface
and the other connector is used for the integral backlight system.
The electronics interface connector is a model I-PEX 20347-340E manufactured by I-PEX.

Table 3. MODULE CONNECTOR PIN CONFIGURATION (CN1)

Pin

1
2
3
4
5
6
7

19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40

Ver. 0.5 29, Jul., 2008

EDID

EDID

EDID

Rin1-

www.jxlcd.com

www.jxlcd.com

BIST/Connector TestBIST/CT1
Power Supply (3.3V typ.)VDD
Power Supply (3.3V typ.)VDD
DDC 3.3V powerV
DDC clock / SMBus clockCLK
DDC data / SMBus dataDATA

- LVDS differential data input (R0-R5,G0)Rin0­+ LVDS differential data input (R0-R5,G0)Rin0+8
GroundVSS9

- LVDS differential data input (G1-G5,B0-B1)10
+ LVDS differential data input (G1-G5,B0-B1)Rin1+11
GroundVSS12

- LVDS differential data input (B2-B5,HS,VS,DE)Rin2-13
+ LVDS differential data input (B2-B5,HS,VS,DE)Rin2+14
GroundVSS15

- LVDS differential clock inputClkIN-16
+ LVDS differential clock inputClkIN+17
GroundVSS18
No ConnectionNC
No ConnectionNC
No ConnectionNC
No ConnectionNC
No ConnectionNC
No ConnectionNC
No ConnectionNC
No ConnectionNC
No ConnectionNC
No ConnectionNC
No ConnectionNC
LED power returnVBL­LED power returnVBL­LED power returnVBL­No ConnectionNC
PWM for luminance controlBLIM
BL On/OffBL_EN
No ConnectionNC
6V-20V LED powerVBL+
6V-20V LED powerVBL+
6V-20V LED powerVBL+
BIST/Connector TestBIST/CT2

DescriptionSymbol

Notes

[LVDS Receiver]

Silicon Works

[Connector]

I-PEX 20347-340E-12

[Mating Connector]

I-PEX 20345-#40E-## series
or equivalent

[Connector pin arrangement]

LCD rear view

1 40

CNT 1

6/ 25

Product Specification

Table 4. BACKLIGHT CONNECTOR PIN CONFIGURATION (CN2)

The LED backlight connector is a model TF12-9S-0.5H, manufactured by Hirose.

1
2
3
4
5
6

8
9

Vdc1
Vdc2
Vdc3
Vdc4
Vdc5
Vdc6

Vdc(1,2,3,4,5,6)
Vdc(1,2,3,4,5,6)

LED Cathode (Negative)
LED Cathode (Negative)
LED Cathode (Negative)
LED Cathode (Negative)
LED Cathode (Negative)
LED Cathode (Negative)
No ConnectionNC7

LED Anode(Positive)
LED Anode(Positive)

LP133WX2

Liquid Crystal Display

NotesDescriptionSymbolPin

1

9

www.jxlcd.com

www.jxlcd.com

Ver. 0.5 29, Jul., 2008

7/ 25