LG LNB5110 User Guide

Specication

OWNER’S MANUAL

High
Denition
Network
Camera

Please read this manual carefully before operating
your set and retain it for future reference.

MODEL
LNB5110 series

Camera

Video /
Audio

Event

Interface

Item LNB5110 series

Image Device 6.28 mm (1/3 Type) CMOS

Lens Type CS mountable

Day/Night ICR (Auto / Day / Night / External / Schedule)

Minimum Illumination

WDR Support

Image Enhancement

Compression H.264, H.264_High, MJPEG

Resolution

Maximum Frame Rate 60 fps @ 1280 x 1024

Multi-Streaming Up to 4

ROI (Region of Interest) Smart codec (Up to 8)

Video Analytics

Text Overlay Support

Audio Compression G.711, G.726

2-way Audio Support

Audio Detection Support

Event Trigger Video analytics, Audio detection, Alarm input

Event Notication Relay Out, Email, FTP

Pre Event Buering Support

Analog Out RCA out

Audio In/Out 1 / 1

Alarm In/Out 1 In / 1 Out

RS-485 Support

SD Slot micro SD (Up to 32 GB)

Color: 0.03 lx (F1.2, Gain : High, 1/30 sec, 50 IRE)

B/W: 0.002 lx (F1.2, Gain : High, 1/30 sec, 50 IRE)

Backlight Compensation, 2D+3D-DNR, De-fog,
Exposure Control, AGC, White Balance, Privacy Masking,
Sharpness, EIS, Pivot

1280 x 1024 / 1280 x 720 / D1 (704 x 576) /
CIF (352 x 240)

Motion detection, Tampering alarm, Face detection,
Intrusion detection, Crossing line, Object counting,
Object removal, Object desertion

Ethernet RJ-45 10/100BASE-T

Security

Open Protocol ONVIF 2.2 Prole S, PSIA 1.1

Network

General

Component

Camera, CD (Software and Owner’s Manual), Installation Manual

Protocol

Integrated Software

Connections Up to 20

Power Source DC 12 V, PoE

Maximum Power
Consumption

Maximum Input Current 490 mA (DC 12 V), 130 mA (PoE)

Operation Temperature/
Humidity

Dimension (W x H x D) 69 mm x 54 mm x 122 mm

Weight 365 g

Password protection, HTTPS (SSL, TLS), IP ltering,
IEEE 802.1X

IPv4 and IPv6 : TCP/IP, UDP, HTTP, HTTPS, RTP, RTSP,
DHCP, ICMP, QoS, UPnP

IPv4 : FTP, SMTP, NTP, ARP, SNMP v1/v2c/v3, DDNS(LG)

LG Ipsolute VMS Suite / Mobile application (iPhone,
iPad, Android)

5.9 W

-10 ºC to 55 ºC / 0 % RH to 80 % RH

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This lightning flash with arrowhead symbol within an equilateral triangle is
intended to alert the user to the presence of uninsulated dangerous voltage
within the product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the
user to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the product.

FCC WARNING: This equipment may generate or use radio frequency energy. Changes or
modifications to this equipment may cause harmful interference unless the modifications are
expressly approved in the instruction manual. The user could lose the authority to operate this
equipment if an unauthorized change or modification is made.

REGULATORY INFORMATION: FCC Part 15

This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful interference to radio
communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own expense.

• A suitable conduit entries, knock-outs or glands shall be provided in the cable entries of this
product in the end user.

• Caution: Danger of explosion if battery is incorrectly replaced. Replaced only with the same or
equivalent type recommended by the manufacturer. Dispose of used batteries according to
the manufacturer’s instructions.

• Holes in metal, through which insulated wires pass, shall have smooth well rounded surfaces
or shall be provided with brushings.

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

Warning: Do not install this equipment in a
confined space such as a bookcase or similar
unit.

Warning: Wiring methods shall be in
accordance with the National Electric Code,
ANSI/NFPA 70.

Warning: This is a class A product. In a
domestic environment this product may cause
radio interference in which case the user may
be required to take adequate measures.

Warning: To reduce a risk of fire or electric
shock, do not expose this product to rain or
moisture.

Warning: Please adopt the power adapter
which can meet the safety extra low voltage
(SELV) standard. And source with DC 12 V or
AC 24 V (depending on models) according
to the IEC60950-1 and Limited Power Source
standard.

Warning: Install the camera on a ceiling or wall
where can withstand the weight of 5 times of
the camera including mounting bracket.

Caution: This installation should be made by a
qualified service person and should conform to
all local codes.

Caution: To avoid electrical shock, do not
open the cabinet. Refer servicing to qualified
personnel only.

Caution: The apparatus shall not be exposed
to water (dripping or splashing) and no objects
filled with liquids, such as vases, shall be placed
on the apparatus.

Caution: Make sure the power supply voltage
is correct before using the camera.

Caution: Do not drop the camera or subject it
to physical shock.

Caution: The sensor may be burned out by
a laser beam, so when any laser equipment is
being used, make sure that the surface of the
sensor not be exposed to the laser beam.

Caution: While shipping, the camera should be
packed in its original packing.

To disconnect power from mains, pull
out the mains cord plug. When installing
the product, ensure that the plug is easily
accessible.

LG Electronics hereby declares
that this/these product(s) is/
are in compliance with the
essential requirements and
other relevant provisions of
Directive 2004/108/EC and
2011/65/EU.

Contact office for compliance of this
product:

LG Electronics Inc.
EU Representative, Krijgsman 1,1186 DM
Amstelveen, The Netherlands

• Please note that this is NOT a Customer
Service contact point. For Customer
Service Information, see Warranty Card
or contact the dealer that you purchased
this product.

Important Safety
Instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings.
Install in accordance with the
manufacturer’s instructions.

8. Do not install near any heat sources such
as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that
produce heat.

9. Do not defeat the safety purpose of the
polarized or grounding-type plug. A
polarized plug has two blades with one
wider than the other. A grounding type
plug has two blades and a third grounding
prong. The wide blade or the third
prong are provided for your safety. If the
provided plug does not fit into your outlet,
consult an electrician for replacement of
the obsolete outlet.

10. Protect the power cord from being
walked on or pinched particularly at plugs,
convenience receptacles, and the point
where they exit from the apparatus.

11. Only use attachments/accessories
specified by the manufacturer.

12. Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination
to avoid injury from tip-over.

13. Unplug this apparatus during lightning
storms or when unused for long periods
of time.

14. Refer all servicing to qualified service
personnel. Servicing is required when
the apparatus has been damaged in any
way, such as power-supply cord or plug
is damaged, liquid has been spilled or
objects have fallen into the apparatus, the
apparatus has been exposed to rain or
moisture, does not operate normally, or
has been dropped.

Handling of the unit

Be careful not to spill water or other liquids on
the unit. Be cautious not to get combustible or
metallic material inside the body. If used with
foreign matter inside, the camera is liable to fail
or to get cause of fire or electric shock.

• Remove dust or dirt on the surface of the
lens with a blower.

• Use a soft and lint-free, dry cloth(such as
glass cleaner) to clean the body. If it is
very dirty, use a cloth dampened with a
small quantity of neutral detergent then
wipe dry.

• Avoid the use of volatile solvents such
as thinners, alcohol, benzene and
insecticides.
They may damage the surface finish and/
or impair the operation of the camera.

• This camera is designed for mounting on
the ceiling or wall. If you install this camera
upside down, it may cause malfunction.

Operating and storage
location

Avoid viewing a very bright object (such as
light fittings) during an extended period. Avoid
operating or storing the unit in the following
locations.

• Extremely hot or cold places (operating
temperature -10 °C to 55 °C, however, we
recommend that the unit be used within a
temperature range of 0 °C to 45 °C)

• Damp or dust place

• Places exposed to rain

• Places subject to strong vibration

• Close to generators of powerful

electromagnetic radiation such as radio or
TV transmitters.

• Do not use the camera in such place
where rapid temperature fluctuation by
switching an air conditioner on and off.

Part Names and Functions

Connection

a

b

c

d

e

f

g
h

k

j

i

a Cap

b Lens iris output connector (LENS)

This 4- pin connector is used to send the Iris control signal and power supply to an auto-iris

type lens.

c Camera installation hole

d VIDEO OUT

e RESET button

Push the button more than 3 seconds, this would restore the factory default network related

settings.

f Power input terminal

Connects to a DC 12 V power supply using proper cables. This camera must always be operated

a DC 12 V. Certied/Listed Adaptor which comply with LPS.

g ETHERNET/PoE Port

Connects to a PC or a network via a hub with a 10 BASE-T/100 BASE-TX cable attached RJ-45

connector.

Power over Ethernet (PoE) is a technology that integrates power into a standard LAN

,

infrastructure. It enables power to be provided to the network device, such as a network
camera, using the same cable as that used for network connection. It eliminates
the need for power outlets at the device locations and enables easier application of
uninterruptible power supplies (LPS).

h Power indicator

Lights when the camera is powered.

i External device connectors

• AUDIO OUT: Connect to an active speaker with a built-in amplier.

• AUDIO IN: Input for a mono microphone, or a line-in mono signal.

• ALARM IN/ALARM IN RET (Sensor input) Terminals: Provides physical interface for sensor.

External Day/Night fucntion is supported as using ALARM IN.

• ALARM OUT/ALARM OUT RET Terminals: Provides physical interface for Alarm/Relay.

• RS-485 (TRX+/TRX-): Connect an external PTZ device.

j micro SD card condition indicator

Lights when the micro SD card is activated normally. Blinks when the recording is in progress

on the micro SD card.

k micro SD card slot

Precautions

• Be sure to switch o the unit before
installation and connection.

• The installation should be made by qualied
service personnel or system installers.

• Do not expose the power and connection
cables to moisture, which may cause
damage to the unit.

Connecting Network

You can control and monitor the system via
network. With the remote control (monitoring),
you can change the system conguration
or monitor the image via network. After the
installation, check the network settings for the
remote control and monitoring work.
Connect the IP camera to your network using a
standard RJ-45 network cable as shown below.

PoE Device

(IEEE802.3af )

Broadband

Service

Router

Broadband

Service

Connecting Power Source

Connect power, using one of the methods
listed below:

To use the power adapter

Connect a DC 12 V power source to the power
input terminal as shown below.
(Recommended power adapter is DC 12 V/

1.5 A or above)
Connect a power source to the power input
terminal with 2 and 3 aligned correctly as
shown below.

• When the connecting Alarm and

,

Audio, tighten the screws as shown
above.

• To remove the connector plug,
as shown below. Put your nger
between the power connector and
the camera body to pull out the
connector.

To use the PoE (Power over Ethernet) device

Connect the PoE cable to the LAN port on the
unit. You must use the “IEEE802.3af” standard
PoE device.

PoE Device

(IEEE802.3af )

If the camera doesn’t work properly after

,

connecting PoE device, please check if
the PoE device supplies enough power.

Connecting Display Device

Connect the video signal between the IP
camera and the monitor.

Connecting Microphone and
Speaker Device

Optionally connect an active speaker and/or
external microphone with a built-in amplier.

Audio OUT

Audio IN

Keep the microphone away from the

,

speaker to avoid howling.

Connecting Alarm Device

Alarm terminals are used to connect the alarm
(relay) devices such as sensors, door switches,
etc.

ALARM IN & OUT / ALARM IN & OUT Ret
(Sensor Input / Relay Output)

Connect the sensor device to the sensor input
terminal.
Connect the alarm (relay) device to the relay
output terminal. Alarm signal is outputted at an
event occurrence.

Sensor
Device

Alarm (relay)

Device

The Photo MOS Relay is rated for

,

100 mA at DC 20 V or 100 mA at AC 28 V.

Connecting PTZ Device

You can control the Pan, Tilt, Zoom, Focus and
Preset when the PTZ device is connected.

PTZ

Device

Installation

Using the micro SD card

You can record your surveillance environment with the micro SD
card even if the network is disconnected condition.

To insert the micro SD card

Insert the micro SD card carefully as shown in the following
illustrations. Make sure the micro SD card terminal position
before insert the micro SD card. Push the back end of the micro
SD card to x it at the last step.

• Do not use the power too much when you insert the

,

micro SD card. The micro SD card may be damaged.

• If you insert the micro SD card in the wrong position,
the micro SD card may be damaged or it may cause
the malfunction of the micro SD Card Slot.

• Keep the terminal part of the micro SD card in clean.
Be careful the terminal part of the micro SD card not
to dusty.

• As the micro SD card is consumable, the micro SD
card end its days and may be not able to save data if
you use it more than over certain times. In this case,
replace micro SD card to buy a new one.

Remove the micro SD card

1. Press the back end of the micro SD card to release the lock
condition.

2. Take the micro SD card out carefully from the camera. It may
cause a malfunction of the micro SD card or the micro SD
card slot if you use the power too much at lock status.

• If you install the micro SD card on the camera

.

and remove with the micro SD card condition
indicator lights on, you must unmount the micro
SD card by using the [System > Storage > Device
Management > Unmount] menu. The micro SD
card data is compromised or the camera may not
operate normally, if you remove the card without use
[Unmount] function.

• LG Electronics is not responsible for deleted data
caused by user mishandling when you insert or
remove the micro SD card.

Recommended the micro SD card specication

Maker Capacity

LG

Less than 32 GB 32 kbyteSandisk

Transcend

Block Size

(FAT 32)

Mounting the Lens

1. Remove the lens mount cap from the camera.

2. Install the CS mount type lens. Carefully align the lens
mount with the camera opening, then turn the lens slowly
to install it. The proper installation is that you face each at
(non-hood) side toward the corner.

3. Connect the lens plug to the lens iris output connector
(LENS) on the side of the camera. When using lenses from
other makers, the plug shape may not correspond to the
terminal on the camera. In such a case, remove the original
plug and using a soldering iron, connect a lens iris plug
according to the diagram.

• Recommended DC-Iris Lens

,

Maker Model name

FUJINON YV2.1x2.8SR4A-SA2L

• We recommend using 6 mm (1/3 type)
Lens of 1.3 Mega Pixel or above.

Lens iris output connector

Pin layout for the lens iris output connector.

No. DC type lenses VIDEO type lenses

1 Damping - Vcc (+9 V)

2 Damping + Not used

3 Drive + Video

4 Drive - Ground

Rewire the lens iris plug

1. Cut o the plug of the lens cable, cut o approximately 8
mm of the insulation, and then strip approximately 2 mm of
the ends of the cable sheaths.

2. Solder the ends of the cable wires to the ends of the pins,
and then attach the cover of the lens iris plug.

Focus adjustment

After installing the lens, you should adjust the focus as shown
below steps.

1. Set the zoom level of the lens approximately.

2. Set the focus of the lens approximately.

Camera Installation

Select a location that is strong enough to bear the full weight
and install the camera securely.

Speed of reading and writing more than 10 MB/Second

,

(Class 6)