LG Electronics LMXS30746S User Manual

ENGLISH FRANÇAIS ESPAÑOL

OWNER’S MANUAL

FRENCH DOOR
REFRIGERATOR

Please read this owner's manual thoroughly before
operating and keep it handy for reference at all times.

LMXS30746S

www.lg.com

2

TABLE OF CONTENTS

TABLE OF CONTENTS

ENGLISH

3 PRODUCT FEATURES

4

IMPORTANT SAFETY
INSTRUCTIONS

7 COMPONENTS

7 Refrigerator Exterior
8 Refrigerator Interior

9 INSTALLATION

9 Installation Overview
10 Specifications
11 Unpacking Your Refrigerator
11 Choosing the Proper Location
11 - Flooring
12 - Ambient Temperature
12 - Measuring the Clearances
12 Removing/Assembling the Refrigerator

Door Handles

13 Removing/Assembling the Freezer

Drawer Handle

13 Removing/Assembling the Doors and

Drawers
14 - Removing the Left Refrigerator Door
15 - Removing the Right Refrigerator Door
16 - Assembling the Right Refrigerator Door
17 - Assembling the Left Refrigerator Door
18 - Removing the CustomChill™ Drawer
19 - Assembling the CustomChill™ Drawer
19 - Removing the Freezer Drawer
21 - Assembling the Freezer Drawer
22 Connecting the Water Line
22 - Before You Begin
22 - Water Pressure
22 - What You Will Need
23 - Water Line Installation Instructions
25 Turning On the Power
26 Leveling and Door Alignment
26 - Leveling
26 - Door Alignment

27 HOW TO USE

27 Before Use
28 Control Panel
28 - Control Panel Features
30 In-Door Ice Bin
30 - Detaching the In-Door Ice Bin
30 - Assembling the In-Door Ice Bin
31 Automatic Icemaker
31

- Turning the Automatic Icemaker On or Off
32 - When You Should Turn the Icemaker Off
32 - Normal Sounds You May Hear
32 - Preparing for Vacation
33 Ice and Water Dispenser
33 - Dispenser
33 - Using the Dispenser
33 - Locking the Dispenser
33 - Cleaning the Dispenser Stand
34 Storing Food
34 - Food Preservation Location
35 - Food Storage Tips
35 - Storing Frozen Food
36 Glide‘N’Access™
36 EasyReach™
37

Detaching and Assembling the Storage Bins
38 CustomChill™ Drawer
39 Adjusting the Refrigerator Shelves

40 MAINTENANCE

40 Cleaning
41 Replacing the Fresh Air Filter
41 Replacing the Water Filter

45 SMART DIAGNOSIS™

45 Using Smart Diagnosis™

46 TROUBLESHOOTING

56 WARRANTY

PRODUCT FEATURES

3

PRODUCT FEATURES

* Depending on the model, some of the following functions may not be available.

FILTERED WATER AND ICE DISPENSER

The water dispenser dispenses fresh, chilled water.
The ice dispenser dispenses cubed and crushed ice.

DOOR ALARM

The Door Alarm function is designed to prevent refrigerator malfunctioning
that could occur if a refrigerator door or freezer drawer remains open. If a
refrigerator door or freezer drawer is left open for more than 60 seconds, a
warning alarm sounds at 30 second intervals.

HUMIDITY CONTROLLED CRISPER

The Humidity Controlled Crisper is designed to help keep your fruits and
vegetables fresh and crisp.

CUSTOMCHILL™ DRAWER

The CustomChill™ Drawer provides storage space with a variable
temperature control that keeps the compartment either colder or warmer
than the refrigerator. Use it to store meat and seafood, cold drinks, deli
snacks, or chilled wine.

ENGLISH

ICE PLUS

Ice production can be increased by approximately 20 percent when the
freezer section is maintained at the coldest temperature for a 24-hour
period.

4

IMPORTANT SAFETY INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS

ENGLISH

READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE.

This guide contains many important safety messages. Always

This is the safety alert symbol. It alerts you to safety messages that inform you of
hazards that can kill or hurt you or others, or cause damage to the product.

All safety messages will be preceded by the safety alert symbol and the hazard
signal word WARNING or CAUTION. These words mean:

WARNING

CAUTION

You can be killed or seriously injured if you do not follow instructions.

Indicates an imminently hazardous situation which, if not avoided, may result
in minor or moderate injury, or product damage.

read and obey

all safety messages.

WARNING

To reduce the risk of fire, electric shock, or personal injury when using your product, basic safety
precautions should be followed, including the following:

Power

NEVER unplug your refrigerator by pulling on the power cord. Always grip the plug firmly and pull it

y

straight out from the outlet.
If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a

y

similarly qualified person in order to avoid a hazard. Do not use a cord that shows cracks or abrasion
damage along its length or at either the plug or connector end.

Do not use an uncertified power outlet.

y

Unplug the power plug immediately in the event of a blackout or thunderstorm.

y

Plug in the power plug with the power cord facing downward.

y

Installation

Contact an authorized service center before you install or relocate the refrigerator.

y

When moving your refrigerator away from the wall, be careful not to roll over or damage the power

y

cord.
Prior to use, ensure that you are connecting this product to a dedicated, grounded electrical outlet

y

rated for use with this product (115V, 60Hz, AC only). It is the user’s responsibility to replace a
standard 2-prong wall outlet with a standard 3-prong wall outlet.

Do not install the refrigerator where there may be a danger of the unit falling.

y

Use

DO NOT allow children to climb, stand, or hang on the refrigerator doors or on the shelves in the

y

refrigerator. They could damage the refrigerator and seriously injure themselves.
Do not hang on to or place heavy objects on the refrigerator’s dispenser.

y

Do not place heavy or dangerous objects (bottles with liquid) on the refrigerator.

y

Do not put live animals inside the refrigerator.

y

Do not allow children to climb into the product when it is in use.

y

In the event of a gas leak (propane/LPG), ensure adequate ventilation and contact an authorized service

y

center before resuming use. Do not touch or disassemble the electric outlet of the refrigerator.
In the event of a refrigerant leak, move flammable objects away from the refrigerator. Ensure adequate

y

ventilation and contact an authorized service center.
Do not use or place flammable substances (chemicals, medicine, cosmetics, etc) near the refrigerator

y

or store them inside the refrigerator. Do not place the refrigerator in the vicinity of flammable gas.

IMPORTANT SAFETY INSTRUCTIONS

5

READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE.

To reduce the risk of fire, electric shock, or personal injury when using your product, basic safety
precautions should be followed, including the following:

This product is not to be used for special purposes such as the storage of medicine or test materials

y

or for use on ships, etc.
Unplug the power plug before cleaning or repairing the refrigerator.

y

When you replace the light bulb in the refrigerator, unplug the refrigerator or turn off the power.

y

Do not modify or extend the power cord.

y

Do not use a dryer to dry the interior. Do not light a candle to remove interior odors.

y

For your safety, this appliance must be properly grounded. Have the wall outlet and the circuit

y

checked by a qualified electrician to make sure the outlet is properly grounded.
Do not use an outlet that can be turned off with a switch. Do not use an extension cord. It is the

y

user’s responsibility to replace a standard 2-prong wall outlet with a standard 3-prong wall outlet.
Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.

y

Do not use an adapter plug and plug the power plug into a multi-outlet extension cord.

y

Disconnect the power cord immediately if you hear a noise, smell a strange odor or detect smoke

y

coming from the appliance.
Turn the power off if water or dust penetrates into the refrigerator. Call a service agent.

y

Do not disassemble or modify the refrigerator.

y

Do not put hands, feet, or metal objects below or behind the refrigerator.

y

Do not operate the refrigerator or touch the power cord with wet hands.

y

In refrigerators with automatic icemakers, avoid contact with the moving parts of the ejector

y

mechanism or with the heating element that releases the cubes. Do not place fingers or hands on the
automatic ice-making mechanism while the refrigerator is plugged in.

When dispensing ice from the dispenser, do not use crystal ceramics.

y

Do not touch the cold surfaces in the freezer compartment with wet or damp hands, when your

y

refrigerator is in operation.
Do not put glass containers, glass bottles or soda in the freezer.

y

This appliance is not intended for use by persons (including children) with reduced physical, sensory

y

or mental capabilities, or lack of experience and knowledge, unless they have been given supervision
or instruction concerning the use of the appliance by a person responsible for their safety.

Do not refreeze frozen food that has thawed completely. Doing so may result in a serious health

y

issue.
If you are throwing away your old refrigerator, make sure the CFC coolant is removed for proper

y

disposal by a qualified servicer. If you release CFC coolant, you may be fined or imprisoned in
accordance with the relevant environmental law.

Junked or abandoned refrigerators are dangerous, even if they are sitting for only a few days. When

y

disposing of the refrigerator, remove the packing materials from the door or take off the doors but
leave the shelves in place so that children may not easily climb inside.

If connected to a circuit protected by fuses, use time delay fuse.

y

ENGLISH

WARNING

This product contains chemicals known to the State of California to cause cancer.

after handling.

Wash hands

6

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE.

ENGLISH

To reduce the risk of fire, electric shock, or personal injury when using your product, basic safety
precautions should be followed, including the following:

CAUTION

Installation

The refrigerator must be properly installed in accordance with the Installer Instructions that were

y

taped to the front of the refrigerator.
Be careful when you unpack and install the refrigerator. Immediately dispose of plastic and other

y

packing materials out of reach of children.
The appliance must be positioned for easy access to a power source.

y

Use

Close the door carefully when children are around.

y

Keep fingers out of pinch point areas; clearances between the doors and cabinets are

y

necessarily small. Be careful closing doors when children are nearby.
If you store food improperly, be aware that it may fall and cause injury.

y

Do not use aerosols near the refrigerator.

y

Do not store articles on the top of the appliance.

y

Maintenance

Do not use strong detergents like wax or thinners for cleaning. Clean with a soft cloth.

y

Wipe foreign objects (such as dust and water) off the prongs of the power plug and contact

y

areas regularly.
Do not store, disassemble or repair the refrigerator by yourself.

y

Remove any dust or foreign matter from the power plug pins.

y

Do not use a wet or damp cloth when cleaning the plug.

y

If the refrigerator is disconnected from the power supply, you should wait for at least five

y

minutes before plugging it back in.
If you notice a chemical or burning plastic smell or see smoke, unplug the refrigerator

y

immediately and contact your LG Electronics Service Center.

SAVE THESE INSTRUCTIONS

COMPONENTS

7

COMPONENTS

Use this page to become more familiar with the parts and features of your refrigerator.
*The appearance and specifications of the actual product may differ depending on the model.

Refrigerator Exterior

Filtered Water and
Ice Dispenser

Dispenses purified water and ice.

LED Display

Displays the refrigerator and freezer
temperature, the water filter
condition and the dispenser status.

Control Panel

Sets the refrigerator and freezer
temperatures, the water filter
condition and the dispenser mode.

Ez Handle

Easily opens the freezer
door.

Handle

Opens and closes
the door.

Refrigerator

Preserves food.

LED Light

LED lights up when
the freezer door is
opened.

CustomChill™
Drawer

Freezer

Preserves frozen food.

ENGLISH

8

COMPONENTS

Refrigerator Interior

ENGLISH

LED interior lamps

The interior lamps light up
the inside of the refrigerator.

Dairy Product Bin

Used to preserve dairy
products.

Adjustable
Refrigerator Shelf

The shelves in your
refrigerator are adjustable
to meet your individual
storage needs.

Indoor Ice Bin

Ice cubes are
automatically produced.

Crisper

Controls humidity and
helps vegetables and
fruit to stay crisp.

CustomChill™ Drawer

Variable temperature storage
that can be set either colder or
warmer than the refrigerator.

Durabase® and Durabase® Divider

The Durabase is a storage space
recommended for the preservation of large
food items. The Durabase Divider is used
to organize the Durabase area into sections.
It can be adjusted from side to side to
accommodate items of different sizes.

Guide Divider

The Guide Divider can be
used to organize the drink
or pitcher area.

Modular Door Bin

Interchangeable bins can
be arranged to suit your
storage needs.

EasyReach™

You can store small items,
or defrost an item.

Auto Closing Hinge

The refrigerator doors
and freezer drawers
close automatically when
you push them slightly.
(The door only closes
automatically when it is
open at an angle of less
than 30°.)

Pullout Drawer

Used for extra storage
within the freezer
compartment.

INSTALLATION

9

INSTALLATION

Installation Overview

Please read the following installation instructions first after purchasing this product or transporting
it to another location.

1 Unpacking your

refrigerator

4 Connecting the water

supply and water line

2 Choosing the proper

location

5 Leveling and Door

Alignment

3 Disassembling/Assembling

ENGLISH

NOTE

Connect to potable water supply only.

10

INSTALLATION

Specifications

ENGLISH

The appearance and specifications listed in this manual may vary due to constant product
improvements.

Dimensions

Net weight

35 3/4" (W) X 38 1/8" (D) X 70 1/4" (H), 48 1/8" (D w/ door open)
908 mm (W) X 968 mm (D) X 1782 mm (H), 1221 mm (D w/ door open)

364 lb. (165 kg)

INSTALLATION

11

Unpacking Your Refrigerator

WARNING

Use two or more people to move and

y

install the refrigerator. Failure to do so
can result in back or other injury.

Your refrigerator is heavy. When moving

y

the refrigerator for cleaning or service,
be sure to protect the floor. Always pull
the refrigerator straight out when moving
it. Do not wiggle or walk the refrigerator
when trying to move it, as floor damage
could occur.

Keep flammable materials and vapors,

y

such as gasoline, away from the
refrigerator. Failure to do so can result in
fire, explosion, or death.

Remove tape and any temporary labels from your
refrigerator before using. Do not remove any
warning-type labels, the model and serial number
label, or the Tech Sheet that is located under the
front of the refrigerator.

To remove any remaining tape or glue, rub the
area briskly with your thumb. Tape or glue residue
can also be easily removed by rubbing a small
amount of liquid dish soap over the adhesive with
your fingers. Wipe with warm water and dry.

Choosing the Proper Location

Select a place where a water supply can

y

be easily connected for the automatic
icemaker.

NOTE

The water pressure must be 20~120
psi or 138~827 kPa or 1.4~8.4 kgf/cm²
on models without a water filter and
40~120 psi or 276~827 kPa or 2.8~8.4
kgf/cm² on models with a water filter.

The refrigerator should always be plugged

y

into its own individual properly grounded
electrical outlet rated for 115 Volts, 60 Hz,
AC only, and fused at 15 or 20 amperes.
This provides the best performance
and also prevents overloading house
wiring circuits which could cause a fire
hazard from overheated wires. It is
recommended that a separate circuit
serving only this appliance be provided.

WARNING

To reduce the risk of electric shock, do not
install the refrigerator in a wet or damp
area.

ENGLISH

Do not use sharp instruments, rubbing alcohol,
flammable fluids, or abrasive cleaners to remove
tape or glue. These products can damage the
surface of your refrigerator.

Refrigerator shelves are installed in the shipping
position. Please reinstall shelves according to
your individual storage needs.

Flooring

To avoid noise and vibration, the unit must be
leveled and installed on a solidly constructed
floor. If required, adjust the leveling legs to
compensate for unevenness of the floor. The
front should be slightly higher than the rear to
aid in door closing. Leveling legs can be turned
easily by tipping the cabinet slightly. Turn the
leveling legs to the left to raise the unit or to
the right to lower it. (See Leveling and Door
AlIgnment.)

NOTE

Installing on carpeting, soft tile surfaces,
a platform or weakly supported structure
is not recommended.

12

INSTALLATION

Ambient Temperature

ENGLISH

Install this appliance in an area where the
temperature is between 55°F (13°C) and 110°F
(43°C). If the temperature around the appliance
is too low or high, cooling ability may be
adversely affected.

Measuring the Clearances

Too small of a distance from adjacent items
may result in lowered freezing capability and
increased electricity consumption charges.
Allow at least 24 inches (61 cm) in front of the
refrigerator to open the doors, and at least
2 inches (5.08 cm) between the back of the
refrigerator and the wall.

24” (61 cm)

Removing/Assembling the
Refrigerator Door Handles

NOTE

When it is necessary to move the
refrigerator through a narrow opening,
removing the doors is the recommended
procedure. If it is necessary to remove
the handles, follow the directions below.

Removing the Handles

Loosen the set screws with a 3/32 in.

1

Allen wrench and remove the handle.

Loosen the mounting fasteners that

2

connect to the refrigerator door and handle
using a 1/4 in. Allen wrench, and remove
the mounting fasteners.

2” (5.08 cm)

Assembling the Handles

Assemble the mounting fasteners at

1

both ends of the handle using a 1/4 in.
Allen wrench.

Place the handle on the door by fitting

2

the handle footprints over the mounting
fasteners and tightening the set screws
with a 3/32 in. Allen wrench.

INSTALLATION

13

Removing/Assembling the
Freezer Drawer Handle

Removing the Handle

Loosen the set screws located on the

1

lower side of the handle with a 1/8 in. Allen
wrench and remove the handle.

Loosen the mounting fasteners that

2

connect to the
freezer drawer
and handle
using a 1/4 in.
Allen wrench,
and remove
the mounting
fasteners.

Assembling the Handle

Assemble the mounting fasteners at

1

both ends of the handle using a
wrench.

Place the handle on the door by fitting

2

the handle
footprints over
the mounting
fasteners and
tightening the
set screws
with a 1/8 in.
Allen wrench.

1

/4 in. Allen

Removing/Assembling the
Doors and Drawers

When it is necessary to move the refrigerator
through a narrow opening, removing the doors
is the recommended procedure.

WARNING

If your entrance door is too narrow for the

y

refrigerator to pass through, remove the
refrigerator doors and move the refrigerator
sideways through the doorway.

Use two or more people to remove and

y

install the refrigerator doors. Failure to do
so can result in back or other injury.

Disconnect the electrical supply to the

y

refrigerator before installing. Failure to do
so could result in serious injury or death.

Do not put hands, feet or other objects into

y

the air vents or bottom of the refrigerator.
You may be injured or receive an electrical
shock.

Be careful when handling the hinge and

y

stopper, to avoid injury.
Remove food and bins before detaching the

y

doors and drawers.

ENGLISH

WARNING

When assembling or disassembling the
handle:

Grasp the handle tightly to avoid dropping it.

y

Do not swing the handle into nearby people

y

or animals.
Make sure that the bracket hole of the

y

handle fits properly into the stopper bolt of
the door. Assemble the set screws to fix
the handle into place.

Make sure that there is not a gap between

y

the door and handle after assembling the
handle.

14

INSTALLATION

Removing the Left Refrigerator Door

ENGLISH

The water supply is connected to the

1

upper right part of the rear surface of the
refrigerator. Remove the ring in the joint
area. Hold the water supply connection
and gently push the Collet to detach the
water supply line as shown in

Collet

NOTE

Detachment of the water supply line is
applicable only when detaching the left
refrigerator door.

Remove the screw from the hinge cover

2

at the top of the refrigerator. Lift the hook
(not visible), located at the bottom of the
front side of the cover with a flat-head
screwdriver.

Remove the cover and pull out the tube .

3

Disconnect all wire harnesses

.

Rotate the hinge lever counterclockwise

4

. Lift the top hinge free of the hinge

lever latch.

Hinge Lever Latch

CAUTION

When lifting the hinge free of the latch, be
careful that the door does not fall forward.

.

Lift the door from the middle hinge pin and

5

remove the door.

CAUTION

Place the door, inside facing up, on a
non-scratching surface.

INSTALLATION

15

Removing the Right Refrigerator
Door

Remove the top hinge cover screw .

1

Lift the hook (not visible), located at the
bottom of the front side of the cover
with a flat-head screwdriver.

Detach the wire harness .

2

Rotate the hinge lever clockwise.

3

Lift the top hinge
lever latch.

,

CAUTION

When lifting the hinge free of the hinge
lever latch, be careful that the door
does not fall forward.

Lift the door from the middle hinge pin and

4

remove the door.

free of the hinge

Hinge Lever Latch

ENGLISH

CAUTION

Place the door, inside facing up, on a
non-scratching surface.

16

INSTALLATION

Assembling the Right Refrigerator

ENGLISH

Door

Install the right-side door first.

Make sure that the plastic sleeve is

1

inserted in the bottom of the door. Lower
the door onto the middle hinge pin as
shown in the figure.

Fit the hinge over the hinge lever latch

2

and slot it into place. Rotate the lever
counterclockwise to secure the hinge.

Connect the wire harness .

3

Make sure that the door-switch located

4

inside the cover is tightly connected.
Position the cover in its place. Insert and
tighten the cover screw

.

Hinge Lever Latch

INSTALLATION

17

Assembling the Left Refrigerator
Door

Install the left refrigerator door after the right
door is installed.

Make sure that the plastic sleeve is

1

inserted in the bottom of the door. Install
the refrigerator door onto the middle hinge.

Fit the hinge over the hinge lever latch

2

and slot it into place. Rotate the lever
clockwise

Hinge Lever Latch

and fasten the hinge.

Push the water supply tube into the hole

4

on the top case and pull it through the
backplate.

Hold the water supply connection and

5

gently push in the collet to connect the
water supply line as shown in
the tube at least 5/8 inch (15 mm) into the
connector.

Collet

ENGLISH

. Insert

Connect all the wire harnesses.

3

Make sure that the door-switch located

6

inside the cover is tightly connected. Place
the cover in its position and tighten the
cover screw .

18

INSTALLATION

ENGLISH

NOTE

Collet

Tube

Insert Line

1) Gently insert the tube until only one
line shows on the tube.

(Correct)

(Incorrect)

2) Pull the tube to make sure that the
tube is tightly fastened.

Removing the CustomChill™ Drawer

Pull the drawer open to full extension.

1

Remove the basket by lifting the basket
from the rail system.

NOTE

Before removing the CustomChill™
drawer, it must be disconnected from
the temperature control.

Disconnect the wire harness connection

2

at the end of the right rail by pressing on
the tabs on either side. It may help to use
a small, flat-blade screwdriver to apply
pressure to the ends of the tabs on either
side.

Hold both sides of the door and lift it to

3

remove it from the rail system.

INSTALLATION

19

Assembling the CustomChill™ Drawer

Grasp the door on each side and lower it

1

into place on the rail system.

Reconnect the wire harness to the

2

connection at the end of the right rail by
aligning the two ends and pushing them
together until you hear a click. The tabs
should snap back into place. Tug gently to
make sure the connection is secure.

Removing the Freezer Drawer

CAUTION

Use two or more people to remove and

y

install the freezer drawer. Failure to do so
can result in back or other injury.

Do not hold the handle when removing

y

or replacing the drawer. The handle may
come off, causing personal injury.

Be careful of sharp hinges on both sides

y

of the drawer.
When you lay the drawer down, be

y

careful not to damage the floor.
Do not sit or stand on the freezer drawer.

y

To prevent accidents, keep children and

y

pets away from the drawer. Do not leave
the drawer open.

Pull the freezer drawer open to full extension.

1

Remove the top pullout drawer by first pulling

2

the drawer open to full extension.

ENGLISH

NOTE

If you do not reconnect the wire
harness securely, the CustomChill™
drawer will not work properly.

Pull the drawer open to full extension.

3

Lower the basket onto the rail system.

On the left rail, use a flat blade screwdriver to
push in on the tab to release the drawer from
the rail, as shown below. Once the left side is
loose, push the tab on the right side with your
finger to release the drawer. Lift the front of
the drawer up, then pull it straight out.

20

INSTALLATION

3

ENGLISH

4

5

Remove the middle drawer by pulling the
drawer out to full extension. Lift the front

of the drawer up, then pull it straight out.

Remove the Durabase by opening the
freezer drawer to full extension and lifting

the basket off of the rail assembly.

Remove the screws from the rails at both
ends.

With both hands, grip both sides of the

6

drawer and pull it up to remove it from the
rails.

CAUTION

Do not hold the handle when removing
or replacing the drawer. The handle may
come off and it could cause personal
injury.

With both hands, hold each rail and push

7

them in simultaneously.

INSTALLATION

21

Assembling the Freezer Drawer

With both hands, pull out each rail

1

simultaneously until both rails are fully
extended.

Grasp the drawer on each side and hook the

2

drawer supports into the rail tabs located on
both sides.

Insert the the top pullout drawer into the

4

frame, and push the drawer back into place
until you hear a click.

Slightly tilt up the front of the middle

5

drawer, insert the drawer into the frame,
and push it back into place.

Insert the lower basket in the rail

6

assembly.

ENGLISH

CAUTION

Do not hold the handle when removing
or replacing the drawer. The handle
may come off and it could cause
personal injury.

Lower the door into final position and

3

tighten the screws located on both sides.

22

INSTALLATION

Connecting the Water Line

ENGLISH

Before You Begin

This water line installation is not covered by the
refrigerator warranty. Follow these instructions
carefully to minimize the risk of expensive water
damage.

Water hammer (water banging in the pipes) in
house plumbing can cause damage to refrigerator
parts and can lead to water leakage or flooding.
Call a qualified plumber to correct water hammer
before installing the water supply line to the
refrigerator.

CAUTION

To prevent burns and product damage,
only connect the refrigerator water line to
a cold water supply.

If you use your refrigerator before connecting
the water line, make sure the icemaker power
switch is in the OFF (O) position.

CAUTION

Do not install the icemaker tubing in
areas where temperatures fall below
freezing.

Water Pressure

The water pressure must be 20~120 psi or
138~827 kPa or 1.4~8.4 kgf/cm² on models
without a water filter and 40~120 psi or 276~827
kPa or 2.8~8.4 kgf/cm² on models with a water
filter.

If a reverse osmosis water filtration system is
connected to your cold water supply, this water
line installation is not covered by the refrigerator
warranty. Follow the instructions carefully to
minimize the risk of expensive water damage.

If a reverse osmosis water filtration system is
connected to your cold water supply, the water
pressure to the reverse osmosis system needs
to be a minimum of 40 to 60 psi (276~414 kPa or

2.8~4.2 kgf/cm², less than 2.0~3.0 sec. to fill a
cup of 7 oz or 198 cc capacity).

CAUTION

Wear eye protection during installation
to prevent injury.

If the water pressure from the reverse osmosis
system is less than 20 psi or 138 kPa or 1.4 kgf/
cm² (takes more than 4.0 sec to fill a cup of 7 oz
or 198 cc capacity):

Check to see if the sediment filter in

y

the reverse osmosis system is blocked.
Replace the filter if necessary.

Allow the storage tank on the reverse

y

osmosis system to refill after heavy
usage.

If the issue concerning water pressure

y

from reverse osmosis remains, call a
licensed, qualified plumber.

All installations must be in accordance

y

with local plumbing code requirements.

What You Will Need

Copper Tubing,

y

connect the refrigerator to the water
supply. Be sure both ends of the tubing
are cut square.

To determine how

y

much tubing you need:
measure the distance
from the water valve on the back of
the refrigerator to the water supply
pipe. Then, add 8 feet (2.4 m). Be sure
there is sufficient extra tubing (about 8
feet [2.4 m] coiled into 3 turns of about
10 in. [25 cm] diameter) to allow the
refrigerator to move out from the wall
after installation.

Power drill.

y

½ in. or adjustable

y

wrench.

Flat blade and Phillips

y

head screwdrivers.

Two ¼ in. outer

y

diameter compression
nuts and 2 ferrules (sleeves)

copper tubing to the shutoff valve and
the refrigerator water valve.

¼ in. outer diameter, to

to connect the

INSTALLATION

23

If your existing copper water line has a

y

flared fitting at the end, you will need
an adapter (available at plumbing supply
stores) to connect the water line to the
refrigerator OR you
can cut off the flared
fitting with a tube
cutter and then use a
compression fitting.

Shutoff valve

y

water line. The shutoff valve should
have a water inlet with a minimum
inside diameter of 5/32 in. at the point of
connection to the COLD WATER LINE.
Saddle-type shutoff valves are included
in many water
supply kits. Before
purchasing, make
sure a saddle-type
valve complies with
your local plumbing codes.

A self piercing saddle type water valve
should not be used.

to connect to the cold

NOTE

Water Line Installation Instructions

WARNING

When using any electrical device
(such as a power drill) during
installation, be sure the device is
battery powered, double insulated
or grounded in a manner that will
prevent the hazard of electric shock.

Install the shutoff valve on the nearest
frequently used drinking water line.

SHUT OFF THE MAIN WATER SUPPLY

1

Turn on the nearest faucet to relieve the
pressure on the line.

CHOOSE THE VALVE LOCATION

2

Choose a location for
the valve that is easily
accessible. It is best to
connect into the side of a
vertical water pipe. When
it is necessary to connect
into a horizontal water
pipe, make the connection to the top or
side, rather than at the bottom, to avoid
drawing off any sediment from the water
pipe.

ENGLISH

DRILL THE HOLE FOR THE VALVE

3

Drill a ¼ in. hole in
the water pipe using
a sharp bit. Remove
any burrs resulting
from drilling the hole
in the pipe. Be careful
not to allow water
to drain into the drill. Failure to drill a ¼ in.
hole may result in reduced ice production
or smaller cubes.

NOTE

The hookup line cannot be white, plastic
tubing. Licensed plumbers must use
only copper tubing (NDA tubing #49595
or #49599) or Cross Link Polyethylene
(PEX) tubing.

24

INSTALLATION

4

ENGLISH

5

FASTEN THE SHUTOFF VALVE
Fasten the shutoff valve to the cold water

pipe with the pipe clamp.

Pipe Clamp

Saddle-Type

Shutoff Valve

Vertical Cold
Water Pipe

NOTE

Commonwealth of Massachusetts
Plumbing Codes 248CMR shall be adhered
to. Saddle valves are illegal and their use is
not permitted in Massachusetts. Consult
with your licensed plumber.

TIGHTEN THE PIPE CLAMP
Tighten the clamp screws until the sealing

washer begins to swell.

Do not overtighten the clamp or

NOTE:

you may crush the tubing.

Washer

Pipe Clamp

Clamp Screw

Inlet End

CONNECT THE TUBING TO THE VALVE

7

Place the compression nut and ferrule
(sleeve) for the copper tubing onto the
end of the tubing and connect it to the
shutoff valve. Make sure the tubing is
fully inserted into the valve. Tighten the
compression nut securely.

Saddle-Type
Shutoff Valve

Packing Nut

Outlet Valve

FLUSH OUT THE TUBING

8

Compression
Nut

Ferrule (sleeve)

Turn the main water
supply on and flush out
the tubing until the water
is clear.

Shut the water off at the

water valve after about
one quart of water has
been flushed through the tubing.

CONNECT THE TUBING TO THE

9

REFRIGERATOR

Before making the connection

NOTE:

to the refrigerator, be sure that the
refrigerator power cord is not plugged into
the wall outlet.

ROUTE THE TUBING

6

Route the tubing between the cold water
line and the refrigerator.

Route the tubing through a hole drilled in

the wall or floor (behind the refrigerator or
adjacent base cabinet) as close to the wall
as possible.

NOTE

Be sure there is sufficient extra tubing
(about 8 feet coiled into 3 turns of
about 10 in. diameter) to allow the
refrigerator to move out from the wall
after installation.

a. Remove the plastic flexible cap from the

water valve.

b. Place the compression nut and ferrule

(sleeve) onto the end of the tubing as
shown.

c. Insert the end of the copper tubing into

the connection as far as possible. While
holding the tubing, tighten the fitting.

Tubing Clamp

¼ in.
Compression
Nut

Ferrule
(sleeve)

¼ in. Tubing

Refrigerator
Connection

INSTALLATION

25

TURN THE WATER ON AT THE SHUTOFF

10

VALVE
Tighten any connections that leak.

CAUTION

Check to see if leaks occur at the water
line connections.

PLUG IN THE REFRIGERATOR

11

Arrange the coil of tubing so that it
does not vibrate against the back of the
refrigerator or against the wall. Push the
refrigerator back to the wall.

START THE ICEMAKER

12

Set the icemaker power switch to the ON
position.

The icemaker will not begin to operate

until it reaches its operating temperature
of 15°F (–9°C) or below. It will then begin
operation automatically if the icemaker
power switch is in the

ON (I)

position.

Turning On The Power

Plug in the refrigerator.

CAUTION

Connect to a rated power outlet.

y

Have a certified electrician check

y

the wall outlet and wiring for proper
grounding.
Do not damage or cut off the ground

y

terminal of the power plug.

ENGLISH

26

INSTALLATION

Leveling and Door Alignment

ENGLISH

Leveling

After installing, plug the refrigerator’s power
cord into a 3-prong grounded outlet and push
the refrigerator into the final position.

Your refrigerator has two front leveling legs—
one on the right and one on the left. Adjust the
legs to alter the tilt from front-to-back or side­to-side. If your refrigerator seems unsteady, or
you want the doors to close more easily, adjust
the refrigerator’s tilt using the instructions
below:

Turn the leveling leg to the left to raise

1

that side of the refrigerator or to the right
to lower it. It may take several turns of the
leveling leg to adjust the tilt of the
refrigerator.

Door Alignment

The left refrigerator door has an adjustable nut,
located on the bottom hinge, to raise and lower
the door for proper alignment.

If the space between your doors is uneven, follow
the instructions below to align the doors:

Use the wrench (included with the Use & Care
Guide) to turn the nut in the door hinge to adjust
the height.
left to lower the height.

Turn it to the right to raise or to the

NOTE

A flare nut wrench works best, but an
open-end wrench will suffice.
Do not over-tighten.

Open both doors again and check to make

2

sure that they close easily. If the doors do
not close easily, tilt the refrigerator slightly
more to the rear by turning both leveling
legs to the left. It may take several more
turns, and you should turn both leveling
legs the same amount.

HOW TO USE

27

HOW TO USE

Before use

Clean the refrigerator.

Clean your refrigerator thoroughly and wipe off all dust that accumulated during
shipping.

Do not scratch the refrigerator with a sharp object or use a detergent that

y

contains alcohol, a flammable liquid or an abrasive when removing any tape
or adhesive from the refrigerator,.
Do not peel off the model or serial number label or the technical information

y

on the rear surface of the refrigerator.

Remove adhesive residue by wiping it off with your thumb or dish detergent.

Connect the power supply.

Check if the power supply is connected before use.
Read the “Turning On The Power” section.

Turn off the icemaker if the refrigerator is not yet connected to the
water supply.

Turn off the automatic icemaker and then plug the power plug of the refrigerator
into the grounded electric outlet.

* This is applicable only to certain models.

ENGLISH

CAUTION

NOTE

CAUTION

Running the automatic icemaker before connecting it to the water
supply may cause the refrigerator to malfunction.

Wait for the refrigerator to cool.

Allow your refrigerator to run for at least two to three hours before putting food in
it. Check the flow of cold air in the freezer compartment to ensure proper cooling.

CAUTION

Putting food in the refrigerator before it has cooled could cause the
food to spoil, or a bad odor could linger inside the refrigerator.

The refrigerator makes a loud noise after initial operation.

This is normal. The volume will decrease as the temperature lowers.

Open refrigerator doors and freezer drawers to ventilate the interior.

The inside of the refrigerator may smell like plastic at first. Remove any adhesive
tape from inside the refrigerator and open the refrigerator doors and the freezer
drawers for ventilation.

28

HOW TO USE

Control Panel

ENGLISH

* Depending on the model, some of the following functions may not be available.

Control Panel Features

Ice Type Ice Type

Press the Ice Type button to choose either cubed
or crushed ice. The cubed or crushed ice icon will
illuminate.

Refrigerator Temperature Refrigerator Temperature

Indicates the set temperature of the refrigerator
compartment in Celsius (°C) or Fahrenheit (°F).

Freezer Temperature Freezer Temperature

Indicates the set temperature of the freezer
compartment in Celsius (°C) or Fahrenheit (°F).

To change the temperature mode from °F to °C
(or vice versa) press and hold the Refrigerator
and Freezer temperature buttons simultaneously
for approximately five seconds. The temperature
indication on the display window switches
between Celsius and Fahrenheit.

NOTE

The displayed temperature is the target
temperature, and not the actual temperature
of the refrigerator. The actual refrigerator
temperature depends on the food inside the
refrigerator.

LED Display
Indicator

Control
Button

( On some

Fresh Air Filter Fresh Air Filter

The Fresh Air Filter helps remove odors from the
refrigerator. The Fresh Air Filter has two settings,
Auto and Power(PWR). In Auto mode, the Fresh
Air Filter will cycle on and off in increments of ten
minutes on and one hundred ten minutes off. If
set to the Power(PWR) mode, the Fresh Air Filter
will stay on continuously for four hours, cycling on
and off in increments of ten minutes on and five
minutes off. After four hours, the Fresh Air Filter
will switch back to Auto mode.

Press the Fresh Air Filter button once for

y

Power(PWR) mode.

Press the Fresh Air Filter button again to

y

switch back to Auto mode.

[

models)

]

HOW TO USE

29

Control Panel Features (continued)

( On some

Change FilterChange Filter

When the Change Filter icon turns on, the air
filter needs to be replaced. After replacing the
air filter, press and hold the Fresh Air Filter
button for three seconds to turn the icon light
off. Change the air filter approximately every
6 months.

[

Ice Plus Ice Plus

This function increases both ice making and
freezing capabilities.

When you touch the

y

graphic will illuminate in the display and
will continue for 24 hours. The function will
automatically shut off after 24 hours.

You can stop this function manually by

y

touching the button one more time.

Ice Plus

Light Light

When you press the Light button, the
dispenser light will turn on and the indicator
will appear on the LED display.

Change Water Filter Change Water Filter

When the Water Filter indicator turns on,
you need to change the water filter. After
changing the water filter, press and hold the
Change Filter button for three seconds to turn
the indicator light off. Change the water filter
approximately every six months.

Door Alarm Door Alarm

When power is connected to the

y

refrigerator, the door alarm is initially set
to ON. When you press the
the display will change to OFF and the

Alarm

function will deactivate.

When either the refrigerator or the freezer

y

door is left open for more than 60 seconds,
the alarm tone will sound to let you know
that the door is open.

When you close the door, the door alarm

y

will stop.

models)

button, the

Alarm

button,

Door

Lock Lock

]

The Lock function disables every other button The Lock function disables every other button
on the display. on the display.

When power is initially connected to the

y

refrigerator, the
If you want to activate the

y

lock other buttons, press and hold the
button for three seconds or more. The
icon will display and the
enabled.

To disable the

y

Lock

the
seconds.

Lock

function is off.

Lock

Lock

function is now

Lock

button for approximately three

function, press and hold

Power Saving ModePower Saving Mode

When the refrigerator is in the

y

Mode

, the display will remain off until a door
is opened or a button is pressed. Once on,
the display will remain on for 20 seconds.

CAUTION

Display Mode (For Store Use Only)

The Display Mode disables all cooling in the
refrigerator and freezer sections to conserve
energy while on display in a retail store. When
activated, OFF will display on the control panel
and the display will remain on for 20 seconds.

To deactivate / activate:

With either refrigerator door opened, press
and hold the Refrigerator and Ice Plus buttons
at the same time for five seconds. The control
panel will beep and the temperature settings
will display to confirm that Display Mode
is deactivated. Use the same procedure to
activate the Display Mode.

function to

Lock

Lock

Power Saving

ENGLISH

30

In-Door Ice Bin

ENGLISH

HOW TO USE

* Depending on the model, some of the

following functions may not be available.

CAUTION

Keep hands and tools out of the ice

y

compartment door and dispenser chute.
Failure to do so may result in damage or
personal injury.

The icemaker will stop producing ice when

y

the in-door ice bin is full. If you need more
ice, empty the ice bin into the extra ice bin
in the freezer compartment. During use,
the ice can become uneven causing the
icemaker to misread the amount of ice
cubes and stop producing ice. Shaking the
ice bin to level the ice within it can reduce
this problem.

Storing cans or other items in the ice bin will

y

damage the icemaker.
Keep the ice compartment door closed

y

tightly. If the ice compartment door is not
closed tightly, the cold air in the ice bin will
freeze food in the refrigerator compartment.
This could also cause the icemaker to stop
producing ice.

If the O

y

N/OFF switch on the icemaker is
set to OFF for an extended period of time,
the ice compartment will gradually warm
up to the temperature of the refrigerator
compartment. To prevent ice cubes from
melting and leaking from the dispenser,
ALWAYS empty the ice bin when the
icemaker is set to OFF for more than a few
hours.

To remove the in-door ice bin, grip the

2

front handle, slightly lift the lower part,
and slowly pull out the bin as shown.

Assembling the In-Door Ice Bin

Carefully insert the in-door ice bin while

1

slightly slanting it to avoid contact with the
icemaker.

Avoid touching the ice-detecting sensor

2

when replacing the ice bin. See the label
on the ice compartment door for details.

Detaching the In-Door Ice Bin

Gently pull the handle to open the ice

1

compartment.

Ice-detecting
sensor

CAUTION

When handling the ice bin,
keep hands away from the
icemaker tray area to avoid
personal injury.