LG offers you a limited warranty that the enclosed
subscriber unit and its enclosed accessories will
be free from defects in material and workmanship,
according to the following terms and conditions:
1. The limited warranty for the product extends for
ONE (1) year beginning on the date of purchase of
the product by the original end user.
2. The limited warranty extends only to the original end
user of the product and is not assignable or
transferable to any subsequent purchaser/end user.
3. This warranty is good only to the original end user of
the product during the warranty period as long as it
is in Canada.
4. Upon request from LG, the consumer must provide
information to reasonably prove the date of
purchase.
5. During the applicable warranty period, LG will repair
or replace at LG’s sole option, without charge to the
original end user, any defective component part of
the phone or accessory.
6. LG may use rebuilt, reconditioned or new parts or
components when repairing any product or replace
a product with a rebuilt, reconditioned or new
product.
2. WHAT THIS WARRANTY DOES NOT COVER:
1. Defects or damages resulting from use of the
product in other than its normal and customary
manner.
2. Defects or damages from abnormal use, abnormal
conditions, improper storage, exposure to moisture
or dampness, unauthorized modifications,
unauthorized connections, unauthorized repair,
misuse, neglect, abuse, accident, alteration,
improper installation or other acts which are not
the fault of LG, including damage caused by spills of
food or liquids.
3. Breakage or damage to antennas unless caused
directly by defects in material or workmanship.
4. The fact that the Customer Service Department at LG
was not notified by the original end user of the
alleged defect or malfunction of the product, during
the warranty period.
5. Products which have had their serial numbers
removed or made illegible.
Page 2
6. Damage resulting from use of non-LG approved
accessories.
7. All plastic surfaces and all other externally exposed
parts that are scratched or damaged due to normal
customer use.
8. Products serviced by non-authorized persons or
companies.
Notes:
1. This limited warranty supersedes all other
warranties, expressed or implied either in fact
or by operations of law, statutory or otherwise,
including, but not limited to any implied warranty of
merchantability or fitness for a particular purpose.
2. Shipping damage is the sole responsibility of the
shipping company.
INCONVENIENCE, LOSS OR ANY OTHER DAMAGES,
DIRECT OR CONSEQUENTIAL, ARISING OUT OF THE
USE OF, OR INABILITY TO USE, THIS PRODUCT OR
FOR ANY BREACH OF ANY EXPRESS OR IMPLIED
WARRANTY, INCLUDING THE IMPLIED WARRANTY OF
MARKETABILITY APPLICABLE TO THIS PRODUCT.
4. HOW TO GET WARRANTY SERVICE:
To obtain warranty service, please call the following
telephone number from anywhere in Canada:
LG Electronics Canada, Inc.
Tel. 1-888-542-2623
www.lg.ca (see links to “Wireless Phone Service”)
3. EXCLUSION OF LIABILITY:
No other express warranty is applicable to this
product.
THE DURATION OF ANY IMPLIED WARRANTIES,
INCLUDING THE IMPLIED WARRANTY OF
MARKETABILITY, IS LIMITED TO THE DURATION OF
THE EXPRESS WARRANTY HEREIN.
LG ELECTRONICS CANADA, INC. SHALL NOT BE
LIABLE FOR THE LOSS OF THE USE OF THE PRODUCT,
Check to make sure that you have all the parts shown below.
HandsetUser GuideTravel ChargerStandard
Battery
10
Page 11
For Your Safety
Important Information
This user guide contains important information on the
use and operation of this phone. Please read all the
information carefully for optimal performance and to
prevent any damage to or misuse of the phone. Any
changes or modifications not expressly approved
in this user guide could void your warranty for this
equipment.
Before You Start
Safety Instructions
WARNING! To reduce the possibility of electric shock,
do not expose your phone to high humidity areas, such
as the bathroom, swimming pool, etc.
Always store your phone away from heat. Never
store your phone in settings that may expose it to
temperatures less than -18°C or greater than 40°C,
such as outside during a snowstorm or in your car on a
hot day. Exposure to excessive cold or heat will result
in malfunction, damage and/or catastrophic failure.
Be careful when using your phone near other
electronic devices. RF emissions from your mobile
phone may affect nearby inadequately shielded
electronic equipment. You should consult with
manufacturers of any personal medical devices such
as pacemakers and hearing aides to determine if
they are susceptible to interference from your mobile
phone. Turn off your phone in a medical facility or at a
gas station. Never place your phone in a microwave
oven as this will cause
IMPORTANT! Please read the TIA SAFETY
INFORMATION on page 74 before using your phone.
the battery to explode.
Safety Information
Please read and observe the following information for
the safe and proper use of your phone and to prevent
any unanticipated damage. Also, keep the user’s manual
in an accessible place at all times after reading it.
] Unplug the power cord and charger during a
lightning storm to avoid electric shock or fire.
] Do not use your phone in high explosive areas.
11
Page 12
For Your Safety
] Do not put your phone in a place subject to
excessive dust, and keep the minimum required
distance between the power cord and heat sources.
] Do not damage the power cord by bending, twisting,
pulling or subjecting it to heat. Do not use the plug if
it is loose as it may cause fire or electric shock.
] Hold the power cord plug firmly to plug and unplug
the power cord. Ensure the plug is firmly connected.
If it is not firmly connected, it may cause excessive
heat or fire.
] Do not place a heavy item on the power cord. Do not
allow the power cord to be crimped as it may cause
fire or electric shock.
] Be careful not to let the battery contact metal
conductors such as a necklace or coins. When
shorted, it may cause an explosion.
] Do not disassemble or impact the battery as it may
cause electric shock, short-circuit and fire. Store the
battery in a place out of reach of children.
] Using a damaged battery or placing a battery in your
mouth may cause serious injury.
12
] Charging is displayed on the screen after connecting
the travel adapter. Only if the battery is completely
drained will the call indicator light be on without
displaying the word “charging”.
] Do not place items containing magnetic components
such as a credit card, phone card, bank book or a
subway ticket, near your phone. The magnetic strip
can be damaged by the phone.
] Do not hold or let the antenna come in contact with
your body during a call.
] Talking on your phone for a long period of time may
reduce the call quality due to heat generated during
the use of the phone.
] Do not allow excessive vibration or impact to the
phone.
] When you do not plan to use the phone for a long
period of time, store it in a safe area with the power
cord unplugged.
Page 13
For Your Safety
FCC RF Exposure Information
WARNING! Read this information before operating the
phone.
In August 1996, the Federal Communications (FCC)
of the United States, with its action in Report and
Order FCC 96-326, adopted an updated safety
standard for human exposure to radio frequency (RF)
electromagnetic energy emitted by FCC regulated
transmitters. Those guidelines are consistent with
the safety standard previously set by both U.S. and
international standards bodies.
The design of this phone complies with the FCC
guidelines and these international standards.
CAUTION
Use only the supplied and approved antenna. Use of
unauthorized antennas or modifications could impair
call quality, damage the phone, void your warranty
and/or result in violation of FCC regulations.
Do not use the phone with a damaged antenna. If a
damaged antenna comes into contact with skin, a
minor burn may result. Contact your local dealer for a
replacement antenna.
Body-worn Operation
This device was tested for typical body-worn operations
with the back of the phone kept 10mm between the
user’s body and the back of the phone. To comply with
FCC RF exposure requirements, a minimum separation
distance of 10mm must be maintained between the
user’s body and the back of the phone. Body-worn
accessories that cannot maintain 3/4 inch (2 cm)
separation distance between the user’s body and the
back of the phone, and have not been tested for typical
body-worn operations may not comply with FCC RF
exposure limits and should be avoided.
Vehicle Mounted External Antenna
(optional, if available)
A minimum separation distance of 8 inches (20 cm)
must be maintained between the user/bystander and
the vehicle mounted external antenna to satisfy FCC RF
exposure requirements.
For more information about RF exposure, visit the FCC
website at www.fcc.gov
13
Page 14
For Your Safety
FCC Part 15 Class B Compliance
This device and its accessories comply with part 15
of FCC rules. Operation is subject to the following two
conditions: (1) This device and its accessories may not
cause harmful interference, and (2) this device and its
accessories must accept any interference received,
including interference that may cause undesired
operation.
Cautions for the Battery
] Do not disassemble.
] Do not short-circuit.
] Do not expose to high temperature: 60°C (140°F).
] Do not incinerate.
Battery Disposal
] Please dispose of your battery properly or bring to
your local wireless carrier for recycling.
] Do not dispose in fire or with hazardous or
flammable materials.
14
Adapter (Charger) Cautions
] Using the wrong battery charger could damage your
phone and void your warranty.
] The adapter or battery charger is intended for indoor
use only.
Do not expose the adapter or battery charger to direct
sunlight or use it in places with high humidity, such as
the bathroom.
Page 15
Your Phone
Phone Components
1. Earpiece
2. Side keys
7. Display screen
8. 5-way joystick or
Navigation key
3. Left soft key
4. Send key
5. Alpha numeric keys
6. Microphone
9. Right soft key
10. Text messaging key
11. End / Power key
12. Clear key
15
Page 16
Your Phone
Your Phone’s Features
1. Earpiece
2. Side keys: These keys are used to control the
volume of ringtone in standby mode and speaker
volume during a call.
3, 9. Left soft key / Right soft key: Each of these keys
perform the functions indicated by the text on the
display immediately above them.
4. Send key: You can use to initiate call once number is
entered and to answer incoming calls. Press this key
in standby mode to quickly access the most recent
incoming, outgoing and missed calls.
5. Alphanumeric keys: These keys are used to dial a
number in standby mode and to enter number or
characters in edit mode.
6. Microphone: Can be muted during a call for privacy.
7. Display screen: Displays phone status icons, menu
items, Web information, pictures and more in full
color.
16
8. 5-way joystick or Navigation key: Enables scrolling
through names, phone numbers, menus or settings.
The 5-way joystick is also used to move the cursor
up and down, right and left when writing text,
using the calendar, and in some game applications.
Pressing the joystick briefly selects the function.
Short press will launch the WAP browser.
10. Text messaging key: One touch access to send a
text message.
11. End / Power key: Allows you to power the phone on
or off, end calls, or return to Standby Mode.
12. Clear key: Allows you to delete the characters
entered or return you to the previous screen.
Page 17
Earmicrophone
jack
Your Phone
Side keys
Textinput key
Toggle between , and text.
Shift key
]A tab for shift function.
]Double tap for shift lock.
Softkeys
The left and right soft keys
activate the prompts that
appear in the soft boxes
directly above them.
Space bar key
Enter a space.
Enter key
Forces a line feed
when editing text.
Backspace
Deletes characters.
Backlight
A backlight illuminates the display and the keypad.
When you press any key or open the flip, the backlight
turns on. It turns off if no key is pressed within a
given period of time, depending on the Backlight
menu option. After one minute, the display turns off to
conserve your battery power. To specify the length of
time the backlight is active, set the Backlight menu
option (Menu 9.1.2). See page 63 for further details.
17
Page 18
Your Phone
Display Information
AreaDescription
Top lineDisplays various icons.
Middle lines
Bottom Line
18
Display messages, instructions and
any information that you enter, such as
number to be dialed.
Shows the functions currently assigned
to the two soft keys.
Icon area
Text and graphic
area
Soft key
indicators
On-Screen Icons
The table below describes various display indicators
or icons that appear on the phone’s display screen.
Icon
Indicates the strength of the network signal.
Indicates a call is in progress.
Indicates that you are roaming off the network.
Indicates that GPRS service is available.
Indicates the alarm has been set and is on.
Indicates the status of the battery charge.
Indicates the receipt of a text message.
Indicates the receipt of a voice mail.
Indicates that you can use the download message
service.
Indicates that the vibration ringer has been set.
Indicates the Silent profile is activated.
Indicates the Headset profile is activated.
Indicates the Car profile is activated.
Indicates the General profile is activated.
Indicates the Schedule function.
Description
Page 19
Getting Started
SIM
SIM
Installing the SIM Card
When you subscribe to a cellular network, you are
provided with a plug-in SIM card loaded with your
subscription details, such as your PIN, any optional
services available and other such information.
n
Important
The plug-in SIM card and its contacts can be easily
damaged by scratches or bending, so be careful when
handling, inserting or removing the card. Keep all SIM
cards out of the reach of small children.
1. Power off the phone by holding down the key
until the power-off image displays.
2. Remove the battery.To do so:
①
SIM
3. Slide the SIM card into the SIM card socket so
that it locks the card into place. Make sure that the
notched corner is facing the bottom left and the gold
contacts of the card face into the phone.
SIM
n
Note
When you need to remove the SIM card, slide it, as shown,
and take it out of the socket.
②
SIM
SIM
19
Page 20
Getting Started
4. Place the battery so that the tabs on the end align
with the slots at the bottom of the phone.
IM
S
5. Press the battery cover until it clicks into place.
Make sure that the battery is properly installed
before switching the phone on.
SIM
20
Charging the Battery
Use of unauthorized accessories could damage your
phone and invalidate your warranty.
To use the travel charger provided with your phone:
1. With the battery in position on the phone, connect
the lead from the travel charger to the bottom of the
phone. Check that the arrow on the lead connector
is facing towards the front of the phone.
2. Connect the adapter to a standard AC wall outlet.
Only use the travel charger that comes included
with the package.
Warning
n
You must unplug the adapter before removing the battery
from the phone otherwise, the phone could be damaged.
Page 21
Getting Started
3. When charging is finished, disconnect the adapter
from the power outlet and from the phone by
pressing on the gray tabs on both sides of the
connector while pulling the connector out.
①
②
①
Notice
n
] If your phone is powered on while charging, you’ll
see the bars in the battery indicator icon cycle.
When the battery is fully charged, the bars in the
battery indicator icon will flash on and off
] If your phone is powered off, the display will
show the charging status. ‘Charging’ or ‘Full’ will
be displayed.
If the battery fails to charge completely:
]
After turning the phone on and off, please attempt to
recharge the battery.
]
After detaching and reattaching the battery, please
attempt to recharge the battery.
21
Page 22
Getting Started
Turning Your Phone On and Off
1. Hold down the key until the phone switches on.
2. If the phone asks for a PIN, enter the PIN and press
the left soft key [OK]. For further details, see page 66.
The phone searches for your network and after finding
it, the idle screen, illustrated below, appears on the
display. Now, you can make or receive a call.
Note
n
The display language is preset to English at the factory.
To change the language, use the Languages menu option
(Menu 9.1.6). For further details, see page 64.
3. When you wish to switch the phone off, hold down
the key until the power-off image displays.
22
Access Codes
You can use the access codes described in this
section to avoid unauthorized use of your phone. The
access codes can be changed by using the Change
Codes feature (Menu 9.4.5).
Security code (4 to 8 digits)
The security code protects the unauthorized use of
your phone. The default security code is set to
‘0000’ and the security code is required to delete all
phone entries and to activate the Restore Factory
Settings menu. The security code default setting can
be modified from the Security Settings menu.
Page 23
General Functions
Making a Call
1. Make sure your phone is powered on.
2. Enter a phone number including the area code. To
edit a number on the display screen, press the right/
left navigation keys to move the cursor to desired
position or simply press the
digit at a time.
]
Press and hold the key to erase the entire
number.
3. Press the
4. To end the call, press the
key to call the number.
Making a Call by pressing the Send Key
1. Press the key, and the most recent incoming,
outgoing and missed phone numbers will be
displayed.
2. Highlight the desired number by using the navigation
key.
3. Press the
key.
key to erase one
key.
Making International Calls
1. Press and hold the
prefix. The ‘+’ character can be replaced with the
international access code.
2. Enter the country code, area code and the phone
number.
3. Press the
key.
key for the international
Ending a Call
To end a call, press the key.
Making a Call From the Contact List
You can store names and phone numbers dialed
frequently in the SIM card as well as the phone
memory known as the Contact List.
You can dial a number by simply looking up a name in
the contact list. For more details on the Contact List
feature, please refer to page 59.
Adjusting the Volume
During a call, if you want to adjust the earpiece
volume, use the side keys of the phone.
In idle mode you can adjust the ring volume using the
side keys.
23
Page 24
General Functions
Answering a Call
When you receive a call, the phone rings and the
flashing phone icon appears on the screen. If the
caller can be identified, the caller’s phone number (or
name if stored in your Address Book) is displayed.
1. Press the
incoming call. If the Any Key menu option (Menu
9.3.2) has been set, any key press will answer a call
except for the
2. End the call by closing the phone or pressing the
key.
n
Notice
You can answer a call while using the Address Book or
other menu features.
Vibrate Mode (Quick)
When the flip is closed, Vibrate Mode can be activated
by holding down the key.
24
key or the left soft key to answer an
key or the right soft key.
Signal Strength
If you are inside a building, being near a window may
give you better reception. You can see the strength
of your signal by the signal indicator (
phone’s display screen.
Entering Text
You can enter alphanumeric characters by using the
phone’s keypad. For example, storing names in the
Address Book, writing a message and scheduling
events in the calendar all require entering text. The
following text input methods are available in the
phone.
T9 Mode
This mode allows you to enter words with only one
keystroke per letter. Each key on the keypad has more
than one letter. The T9 mode automatically compares
your keystrokes with an internal linguistic dictionary to
determine the correct word, thus requiring far fewer
keystrokes than the traditional ABC mode.
) on your
Page 25
n
Notice
The default setting on the phone is ABC mode and T9 can
be chosen to become the default text entry mode. You can
also select a different T9 language from the menu options.
ABC Mode
This mode allows you to enter letters by pressing the
key labeled with the required letter once, twice, three
or four times until the letter is displayed.
123 Mode (Numbers Mode)
Type numbers using one keystroke per number. To
change to 123 mode in a text entry field, press key
until 123 mode is displayed.
Symbol Mode
This mode allows you to enter special characters.
Changing the Text Input Mode
1. When you are in a field that allows characters to be
entered, you will notice the text input mode indicator
in the upper right corner of the display.
2. If you want to change modes, press and hold down
3. To switch to Symbol mode, press the
key. The available modes are displayed.
the
key.
General Functions
Using the T9 Mode
The T9 predictive text input mode allows you to enter
words easily with a minimum number of key presses.
As you press each key, the phone begins to display
the characters that it thinks you are typing based on a
built-in dictionary. As new letters are added, the word
changes to reflect the most likely candidate from the
dictionary.
1. When you are in the T9 predictive text input mode,
start entering a word by pressing keys
Press one key per letter.
] The word changes as letters are typed - ignore
what’s on the screen until the word is typed
completely.
] If the word is still incorrect after typing completely,
press the down navigation key once or more to
cycle through the other word options.
Example: Press
Press
to type Good
[down navigation key] to
type Home
] If the desired word is missing from the word
choices list, add it by using the ABC mode.
to .
25
Page 26
General Functions
2. Enter the whole word before editing or deleting any
keystrokes.
3. Complete each word with a space by pressing the
key.
To delete letters, press
.
Press and hold down to erase entire words.
n
Notice
To exit the text input mode without saving your input, press
.
Using the ABC Mode
Use the to keys to enter your text.
1. Press the key labeled with the required letter:
]
Once for the first letter
]
Twice for the second letter
]
And so on
2. To insert a space, press the
letters, press the key. Press and hold down the
key to clear the display.
n
Notice
Refer to the table below for more information on the
characters available using the keys.
26
key once. To delete
Please note the character availability is dependent on the
language selected.
Characters in the Order Display
Key
Upper CaseLower Case
. , - ¿ ? ¡ ! ‘ @ : 1. , - ¿ ? ¡ ! ‘ @ : 1
1
A B C À Á Ã Ä Ç 2a b c à á ã ä ç 2
2
D E F È É Ê Ë 3d e f è é ê ë 3
3
G H I Í Î Ï 4g h i í î ï 4
4
J K L 5j k l 5
5
M N O Ó Ô Ö Ñ 6m n o ó ô ö ñ 6
6
P Q R S 7p q r s 7
7
T U V Ù Ú Û Ü 8t u v ù ú û ü 8
8
W X Y Z 9w x y z 9
9
Space KeySpace Key
0
Page 27
Using the 123 (Numbers) Mode
The 123 Mode enables you to enter numbers in a text
message (a telephone number, for example).
Press the keys corresponding to the required digits
before manually switching back to the appropriate text
entry mode.
Using the Symbol Mode
The Symbol Mode enables you to enter various
symbols or special characters.
To enter a symbol, press the
navigation keys to select the desired symbol and press
the key.
key. Use the
General Functions
27
Page 28
Selecting Functions and Options
Your phone offers a set of functions that allows you to customize the phone. These functions are arranged in menus
and sub-menus, accessed via the two soft keys marked and
alter the settings of a particular function.
The roles of the soft keys vary according to the current context; the label on the bottom line of the display just above
each key indicates its current role.
Press the left soft key
to acces the available
Menus.
28
. Each menu and sub-menu allows you to view and
Press the right soft key
to acces the Internet.
Page 29
Address Book
You can store phone numbers and their corresponding names in the memory of your SIM card.
In addition, you can store up to 255 numbers and names in the phone memory.
The SIM card and phone memory, although physically separate, are utilized like a single entity known as the
List (See page 59 for details).
Contact
29
Page 30
In-Call Menu
Your phone provides a number of control functions that
you can use during a call. To access these functions
during a call, press the left soft key [Options].
1. Contact List 5. Send DTMF
2. Hold Call 6. Mute
3. End Call 7. Write Memo
4. Text Message 8. Voice Recording
During a Call
The menu displayed on the handset screen during a
call is different than the default main menu displayed
while in the idle screen, and the options are described
below.
Making a Second Call
You can get a number you wish to dial from the
Address Book to make a second call. Press the left soft
key, then select Contact List.
Swapping Between Two Calls
To switch between two calls, press the key.
30
Answering an Incoming Call
To answer an incoming call when the handset is
ringing, press the . The handset is also able to
warn you of an incoming call while you are already on
a call. A tone sounds in the earpiece, and the display
will show that a second call is waiting.
This feature, known as Call Waiting, is only available if
your network supports it. For details of how to activate
and deactivate it see Call Waiting (Menu 9.3.4).
If Call Waiting is on, you can put the first call on hold
and answer the second, by pressing
You can end the current call and answer the waiting
call by pressing the left soft key [Options] and then
selecting Active call in the End call submenu.
.
Rejecting an Incoming Call
You can reject an incoming call without answering by
simply pressing the key or holding the when the
flip is closed.
During a call, y
pressing the right soft key and selecting Reject call.
ou can reject an incoming call by
Page 31
In-Call Menu
Muting the Microphone
You can mute the microphone during a call by pressing
the right soft key Mute or going to the [Options] then
selecting Mute. The handset can be unmuted by
selecting by pressing the right soft key [Unmute] or
choosing Unmute in the [Options].
Multiparty or Conference Calls
The multiparty or conference service provides you
with the ability to have a simultaneous conversation
with more than one caller, if your network service
provider supports this feature. A multiparty call can
only be set up when you have one active call and
one call on hold and both calls have been answered.
Once a multiparty call is set up, calls may be added,
disconnected or separated (that is, removed from the
multiparty call but still connected to you) by the person
who sets up the multiparty call. These options are all
available from the In-Call menu. The maximum callers
in a multiparty call are five. Once started, you are in
control of the multiparty call and only you can add
callers to the multiparty call.
Making a Second Call
You can make a second call while currently on a call.
Enter the second number and press the . When the
second call is connected, the first call is automatically
placed on hold. You can swap between calls, by
pressing the
key.
Setting up a Conference Call
To set up a conference call, place one call on hold
and while the active call is on, press the left soft key
[Options] then select Conference and then Join.
Activate the Conference Call on Hold
To activate a conference call on hold, press the left
soft key [Options] then select Retrieve Call.
Adding Calls to the Conference Call
To add a call to an existing conference call, dial
another number, press the left soft key [Options Menu]
then select Conference and then Join.
31
Page 32
In-Call Menu
Private Call in a Conference Call
To have a private call with one caller from a
conference call, dial another number, press the left
soft key [Options Menu] then select Conference and
then Private.
Ending a Conference Call
Currently displayed caller from a conference call can
be disconnected by pressing the
key.
32
Page 33
Menu Tree
The following illustration shows the available menu structure and indicates the:
] Number assigned to each menu option.
] Page where you can find the feature description.
1. Recent Calls (see page 37)
1.1 Missed Calls
1.2 Dialed Calls
1.3 Received Calls
1.4 Delete Recent Calls
1.5 Call Durations
1.5.1 Last Call
1.5.2 Received Calls
1.5.3 Dialed Calls
1.5.4 All Calls
1.6 Data Information
1.6.1 WAP Information
1.6.2 External Device
1.6.3 Total Data
2. Messaging (see page 39)
2.1 Text Messages
2.1.1 Write Message
2.1.2 Inbox
2.1.3 Sent
2.1.4 Drafts
:Shown only if supported by SIM card
*
2.1.5 Settings
2.1.6 Delete All
2.2 Multimedia Messages
2.2.1 Write Message
2.2.2 Inbox
2.2.3 Outbox
2.2.4 Sent
2.2.5 Drafts
2.2.6 Settings
2.3 Voice Mail
2.3.1 Listen To Voice Mail
2.3.2 Voice Mailbox Number
2.4 Download Messages
2.4.1 Inbox
2.4.2 Receive
2.5 Templates
2.5.1 Text
2.5.2 Multimedia
2.5.3 Business Card
33
Page 34
Menu Tree
2.6 Memory Status
2.6.1 Text
2.6.2 Multimedia
3. Games & Apps (see page 48)
3.1 Download Games
3.2 Games & Apps
3.3 Access Point
3.4 Information
3.4.1 Memory Status
3.4.2 Java Version
4. Media Services (see page 50)
4.1 Games & Apps
4.2 Ringtone/Audio
4.3 Images
4.4 Media Services
4.5 View Online Album
5. Internet (see page 52)
5.1 GoRogers
5.2 Access Point
5.3 Cache Settings
5.3.1 Clear Cache
34
5.3.2 Cache Check
5.4 Security Certifi cates
5.5 WAP Information
6. Sounds (see page 54)
6.1 Download Ring Tunes
6.2 Ringtones
6.3 Volume
6.4 Ring Alert Type
6.5 Message Alert Tones
6.6 Key Tones
6.7 Voice Recording
Page 35
Menu Tree
7. Tools (see page 55)
7.1 Alarm Clock
7.2 Calendar
7.3 Voice Recording
7.4 Calculator
7.5 Memo
7.6 World Time
7.7 Unit Converter
8. Address Book (see page 59)
8.1 Contact List
8.2 New Contact
8.3 Speed Dials
8.4 Voice Tag List
8.5 Caller Groups
8.6 Copy All
8.6.1 SIM To Phone
8.6.2 Phone To SIM
8.7 Delete All
8.8 Set Memory
:Shown only if supported by SIM card
*
8.9 Information
8.9.1 Memory Status
8.9.2 Own Number
9. Settings (see page 63)
9.1 Display
9.1.1 My Wallpaper
9.1.2 Backlight
9.1.3 Contrast
9.1.4 Screen Saver
9.1.5 Power On Sound
9.1.6 Languages
9.1.7 Menu Style
9.2 Date & Time
9.2.1 Set Date
9.2.2 Date Format
9.2.3 Set Time
9.2.4 Time Format
9.2.5 Auto Update
35
Page 36
Menu Tree
9.3 Call Settings
9.3.1 Call Forwarding
9.3.2 Answer Mode
9.3.3 Send My Number
9.3.4 Call Waiting
9.3.5 Minute Minder
9.3.6 Auto Redial
9.3.7 Send DTMF
9.4 Security
9.4.1 PIN Code Request
9.4.2 Phone Lock
9.4.3 Auto Key Lock
9.4.4 Call Barring Service
9.4.5 Fixed Dial Number
9.4.6 Change Codes
9.5 Connection
9.5.1 Network Selection
9.5.2 GPRS Attach
9.5.3 Access Point
9.5.4 Reset Access Point
9.6 Reset Setting
36
:Shown only if supported by SIM card
*
Page 37
Recent Calls
You can check the record of missed, received and
dialed calls only if the network supports the Calling
Line Identification (CLI) within the service area.
The number and name (if available) are displayed
together with the date and time at which the call was
made. You can also view call times.
Missed Calls Menu 1.1
This option lets you view the last 10 unanswered calls.
You can also:
• View the number if available and call it, or save it in
the Address Book
• Enter a new name for the number and save both in
the Address Book
• Send a message to this number
• Delete the call from the list
Dialed Calls Menu 1.2
This option lets you view the last 20 outgoing calls
(called or attempted). You can also:
• View the number if available and call it, or save it in
the Address Book
• Enter a new name for the number and save both in
the Address Book
• Send a message to this number
• Delete the call from the list
Received Calls Menu 1.3
This option lets you view the last 20 incoming calls. You
can also:
• View the number if available and call it, or save it in
the Address Book
• Enter a new name for the number and save both in
the Address Book
• Send a message to this number
• Delete the call from the list
Delete Recent Calls Menu 1.4
Allows you to delete the Missed, Received and Dialed
Calls lists. You can delete the All Calls list at one time.
37
Page 38
Recent Calls
Call Durations Menu 1.5
Allows you to view the duration of your incoming and
outgoing calls. You can also reset the call time. The
following timers are available:
Last Call (Menu 1.5.1)
Length of the last call.
Received Calls (Menu 1.5.2)
Length of the incoming calls.
Dialed Calls (Menu 1.5.3)
Length of the outgoing calls.
All Calls (Menu 1.5.4)
Total length of all calls made and incoming calls since
the timer was last reset.
Notice
n
The actual time invoiced for calls by your service provider
may vary, depending upon network features, rounding-off
for billing and so forth.
38
Data Information Menu 1.6
You can check the amount of data transferred over the
network through the GPRS information option.
In addition, you can also view how much time you are
online.
n
Notice
GPRS General Packet Radio Service
WAP Information (Menu 1.6.1)
You can check the data volume and the duration
through WAP.
External Device (Menu 1.6.2)
You can check the data volume and the duration
through GPRS by using an external device such as a
serial port.
Total Data(Menu 1.6.3)
You can check the total amount of data through WAP
and an external device.
Page 39
Messaging
Text Messages Menu 2.1
Your phone can receive voice mail notification
messages and Short Message Service (SMS)
messages.
Voice mail and SMS are network services. Please
contact your service provider for more information.
When the
new voice mail. When the icon appears, you have
received a new text message. If the message memory
is full, an error message is displayed, the icon
flashes and you cannot receive any new messages.
Use the Delete option in the Inbox (Menu 2.1.2) to
delete obsolete messages. Once there is space in
the memory, any undelivered SMS messages will be
received (provided sufficient space is available).
Write Message (Menu 2.1.1)
You can write and edit text messages of up to 918
characters.
1. Type in a message using alphanumeric keypad. For
details on how to enter text, refer to page
2. After completing the message, select the required
option by pressing the left soft key [Option].
icon appears, you have received a
24 (Entering Text).
The following options are available.
]
Send To Number: Enter the phone number or select
the number from the address book.
]
Send To Email: Enter the email or select the email
from the address book.
]
Save To Drafts: Save the message so that it can be
sent later.
]
T9 Languages: Choose between English, Spanish or
French T9 language. For details on how to enter text,
refer to page 25 (Using the T9 Mode).
]
Clear Text: Delete the written message.
]
Exit Editor: Exit the text editor.
The following options are available. (Press the right
soft key [Insert])
]
Symbol: Attaches special characters.
]
Text Templates: Use the text templates already set in
the phone.
]
Phone Number: Attaches a phone number.
]
Business Card: Attaches your name card.
39
Page 40
Messaging
Inbox (Menu 2.1.2)
Received text messages, page messages and email
lists may be searched and the contents may be
viewed. Received messages are displayed from
newest to oldest.
The following options are available.
]
Reply: Replies to the received message.
]
Delete: Deletes the selected message from the Inbox.
]
Forward: Forwards a received message to other
recipients. After recipients are entered, the message
can be forwarded.
]
Return Call: Calls back the sender.
]
Extract: Extracts a phone number and email address
from the message.
40
Sent (Menu 2.1.3)
Shows lists and contents of sent messages in this
menu and also verifies if transmission was successful.
The following options are available.
]
Delete: Deletes the selected message from the Outbox.
]
Forward: Forwards the current message to other
recipients.
Drafts (Menu 2.1.4)
This menu option shows the draft message list. Scroll
through the list using the up/down navigation keys.
The following options are available.
]
View: You can view a selected message.
]
Delete: Deletes the selected draft message.
]
Edit: You can edit a selected message.
]
Delete All: Allows you to erase all messages.
Page 41
Messaging
Settings (Menu 2.1.5)
This menu allows you to set up default SMS
information.
] Message Types: Allows you to set the default message
type (Text,Voice, Fax, Paging, X.400, E-mail, ERMES). The
network can convert the messages into the selected
format. The type of message you desire can be set to Text
Type.
]
Valid Period: Allows you to set the length of time
for which your text messages will be stored at the
SMS center while attempts are made to deliver them
to the recipient. Possible values are Maximum, 30
Minutes, 1 Hour, 6 Hours, 1 Day and 1 Week which
can be authorized by your service provider.
] Delivery Reports: Allows you to activate or deactivate
the report function. When this function is activated, the
network informs you whether or not your message has
been delivered.
]
Reply With Same Service: Allows the recipient of
your SMS message to send you a reply via your
message center, if the service is provided by the
network.
] Message Center Number: Allows you to store or change
:Shown only if supported by SIM card
*
the number of your email gateway required when sending
text messages. You must obtain this number from your
service provider.
]Email Gateway: Allows you to store or change the
number of your email gateway required when sending text
messages.
]
Subject: If you set it to Yes, allows you to enter the
subject.
]
Bearer Setting: You can select GPRS or GSM.
Contact your network operator or service provider
for information related to setting a selected bearer,
pricing and connecting speed.
GSM Preferred / GPRS Preferred
Delete All (Menu 2.1.6)
Allows you to delete all text messages.
Multimedia Messages Menu 2.2
A multimedia message can contain text, images,
and / or sound clips. This feature can be used only
if it is supported by your network operator or service
provider. Only devices that offer compatible multimedia
message or e-mail features can receive and send
multimedia messages. Attach to add Symbol, Picture,
41
Page 42
Messaging
Sound, Recorded Voice, Text Template.
Write Message (Menu 2.2.1)
The following options are available.
]
Send: Supports multiple number and email addresses.
]
Preview: Allows you to see the multimedia message
you wrote.
]
Save: Allows you to save multimedia messages as a
draft or as templates.
]
Delete: Deletes the MMS message.
]
Slide Duration: Allows you to set a timer for the slide
and text.
]
Slide Format: Allows you to make the message
contents aligned right, left, top and bottom.
]
Add Slide: Allows you to add a slide before or after
the current slide.
]
Add Sound: Allows you to add a sound before or
after the current sound.
]
Delete Image: Deletes the current image.
]
Delete Sound: Deletes the current sound.
n
Note
Delete Image and Delete Sound options will only be visible
42
after image or sounds are created within a new message.
Inbox (Menu 2.2.2)
You will be alerted when you have received messages.
They will be stored in the Inbox. In the Inbox, you can
identify each message by icons. For detail, see the
icon directive below.
If the phone has ‘no space for message’, you can make
space in each repository by deleting messages, media
and applications.
]
Timer Stop: Timer stop menu is displayed when you
receive the message including various pictures.
Usually, the pictures slide automatically.
However, if you select this menu, you can see the
next picture by pressing the left soft key manually.
]
Previous Slide: View the previous page.
]
Restart: Allows you to replay multimedia messages.
]
Save Message: Allows you to save a multimedia
message in draft or as template.
]
Save Items: Allows you to extract picture and sound.
]
Details: Allows you to view information about
received messages; Sender’s address, Subject (only
for multimedia message), Message date & time,
Page 43
Messaging
Message type, Message size.
]
Reply: Allows you to reply to the sender.
]
Reply All: Allows you to reply to the senders.
]
Delete Message: Allows you to delete the current
message.
]
Forward: Allows you to forward the selected
message to other recipients.
Outbox (Menu 2.2.3)
Allows you to see sent messages here.
Sent (Menu 2.2.4)
Sent messages are stored, and you can see them here.
]
Timer Stop: Timer stop menu is displayed when you
receive the message including various pictures.
Usually, the pictures slide automatically. However, if
you select this menu, you can see the next picture by
pressing the left soft key manually.
]
Previous Slide: View the previous page.
]
Restart: Allows you to replay current messages.
]
Save Message: Allows you to save multimedia
message in draft or as template.
]
Save Items: Saves the item such as image or sound
as an attachment in a message.
]
Details: Allows you to view information about outbox
messages; Subject (only for multimedia message),
Message date & time, Message type, Message size.
]
Reply: Allows you to reply to the current message.
]
Reply All: Allows you to reply to all the messages.
]
Delete Message: Allows you to delete the current
message.
]
Forward: Allows you to forward the current message
to other recipients.
Drafts (Menu 2.2.5)
Using this menu, you can preset up to five multimedia
messages that you use most frequently. This menu
shows the preset multimedia message list.
The following options are available.
]
Send:
Supports multiple number and email addresses.
]
Preview: Allows you to see the multimedia message
you wrote.
]
Save: Allows you to save multimedia messages as a
draft or as templates.
]
Delete: Allows you to delete the image or sound.
43
Page 44
Messaging
]
Slide Duration: Allows you to set a timer for the slide
and text.
]
Slide Format: Allows you to make the message
contents aligned right, left, top and bottom.
]
Add Slide: Allows you to add a slide before or after
the current slide.
]
Remove Slides: Removes slides from your message.
]
Add Sound: Add sound to your message.
n
Note
You must create one draft multimedia message in order to
see some of the listed options.
Settings (Menu 2.2.6)
Via this menu, you can set up default multimedia
message information.
The following options are available:
]
Message Subject: Enter the message title.
]
Slide Duration: Displays the duration of each page
when writing the message.
]
Alignment: Set the position of a message and text
message.
•Image Bottom•Image Left
44
:Shown only if supported by SIM card
*
Image Top • Image Right
•
]
Validity Period: Set the duration for keeping
messages on the network server. Options are:
Maximum, 30 Minutes, 1 Hour, 6 Hours, 1 Day or 1 Week.
]
Auto Download
• On: If you select this, messages are downloaded
automatically on receipt.
• Off: Defers downloading messages.
]
Message Center URL: Enter the address of an MMS
server to use the MMS service.
]
Access Point: For further details, see page 53.
n Note
During MMS receive mode, there will be a red arrow icon
in the upper right corner of the stand-by screen. WAP and
MMS menus will not be accessible.
Voice Mail Menu 2.3
This menu provides you with a quick way of accessing
your voice mailbox (if provided by your network).
Before using this feature, you must enter the voice
server number obtained from your service provider.
When a new voicemail is received, the symbol will
Page 45
Messaging
be displayed on the screen. Please check with your
network service provider for details of their service in
order to configure the handset accordingly.
Listen To Voice Mail (Menu 2.3.1)
Before using this feature, you must enter the voice
server number obtained from your service provider.
You can then select this option and press the OK soft
key to listen to your messages.
You can quickly connect to the first voice server by
pressing and holding the
key in Idle Mode.
Voice Mailbox Number (Menu 2.3.2)
Allows you to change the voice mail server number, if
necessary.
n
Note
Voice Mail is a network feature. Please contact your
service provider for further details.
Download Messages Menu 2.4
Inbox (Menu 2.4.1)
You can order push messages from WAP service
providers. Push messages are notifications of, for
example, news headlines and they may contain a text
message or address of a WAP service. For availability
and subscription, contact your WAP service provider.
Service providers can update an existing push
message every time a new push message is received.
Messages can be updated even if you have moved
them to another folder. Push messages expire and they
are deleted automatically.
]
Information: Shows the information of received push
messages.
]
Load: Allows you to connect to a specific site using
the information in the received push message.
]
Delete: Deletes the selected push message.
Receive (Menu 2.4.2)
You can set the option whether you will receive the
message or not.
Templates Menu 2.5
There are 6 predefined messages in the list. You can
view and edit the template messages or create new
messages.
Text (Menu 2.5.1)
45
Page 46
Messaging
• Please call me back • I’m late. I will be there at
• Where are you now? • I’m on the way.
• Urgent! Please contact. • I love you
The following options are available.
]
Edit: Allows you to write a new message or edit the
selected template message.
]
Send Via Text Message: Sends the selected template
message by SMS.
]
Send Via Multimedia Message: Sends the selected
template message by MMS.
]
Delete: Allows you to delete the selected template
message.
Multimedia (Menu 2.5.2)
For further details, see pa
]
Send:
Supports multiple number and email addresses.
]
Preview: To see the multimedia message you wrote.
]
Save: Allows you to save multimedia messages as a
draft or as templates.
]
Delete: Deletes the MMS message.
]
Slide Duration: Allows you to set a timer for the
slide and text.
46
ge 41.
]
Slide Format: Allows you to make the message
contents aligned right, left, top and bottom.
]
Add Slide: Allows you to add a slide before or after
the current slide.
]
Add Sound: Allows you to add a sound before or
after the current sound.
Business Card (Menu 2.5.3)
This option allows you to make your own name card.
Key in the Name, Mobile number, Office number, Fax
number and E-mail address.
]
Edit: Allows you to write a new message or edit the
selected name card.
]
Send Via Text Message: Sends the selected name
card by SMS.
]
Send Via Multimedia Message: Sends the selected
name card by MMS.
]
Delete: Allows you to delete the selected name card.
Page 47
Memory Status Menu 2.6
You can check the current memory status for Text and
M
ultimedia messages.
Text (Menu 2.6.1)
You can check the current memory status for
Messaging and Delivery Reports.
Multimedia (Menu 2.6.2)
You can check the current memory status for Total,
Used and Free.
Messaging
47
Page 48
Games & Apps
Java is a technology developed by Sun Microsystems.
Similar to the way you would download the Java
Applet using the standard Netscape or MS Internet
Explorer browsers, Java MIDIet can be downloaded
using the WAP enabled phone. Depending on the
service provider, all Java based programs such as
Java games can be downloaded and run on a phone.
Once downloaded, the Java program can be viewed
within the Games & Apps menu where you can select,
execute or delete. The Java program files saved in the
phone are in .JAD and .JAR formats.
n
Note
The JAR file is a compressed format of the Java program
and the JAD file is a description file that includes all
detailed information. From the network, prior to download,
you can view all detailed file descriptions from the JAD file.
n Warning
Only J2ME (Java 2 Micro Edition) based programs will run
in a phone environment.
The J2SE (Java 2 Standard Edition) based programs will
only run in a PC environment.
48
Download Games Menu 3.1
This menu option connects to Rogers’ game download
site.
Games & Apps Menu 3.2
Games & Apps menu displays the list of Java programs
downloaded. All previously downloaded programs
can be selected, deleted or viewed in detail within the
Games & Apps menu. From the list within the Games &
Apps menu, the following options are available:
]
Open: Opens the selected program. The list includes
all Java programs installed in the phone.
]
Delete: Deletes the selected program. Once deleted,
you will not be able to restore the program unless it
is downloaded again using the WAP.
]
Send Information: Selected Java MIDIet information
such as MIDIet name, size, version, vendor and jad
URL can be sent via SMS.
Page 49
]
Information: Display detailed information on the
selected program. This includes the program name,
program size, program version, vendor information
and the website address or the URL.
Access Point Menu 3.3
For futher details, see page 53.
Information Menu 3.4
The downloaded programs using WAP are stored
in the phone memory. There is a maximum memory
capacity in the phone and once you exceed this
memory, you will not be able to store any more
programs. The View Information menu allows you to
check the available memory capacity in the phone.
Memory Status (Menu 3.4.1)
Displays maximum memory capacity and total
available memory information.
Java Version (Menu 3.4.2)
Displays current Java version.
Games & Apps
49
Page 50
Media Services
Games & Apps Menu 4.1
For further details, se
e page 48 (Menu 3.2).
Ringtone / Audio Menu 4.2
The left soft key [Options] will bring up the following
option.
]Send Via Text Message: Downloaded sound can be
sent via SMS.
]Send Via Multimedia Message: Downloaded sound
can be sent via MMS.
]Set As Ring Tone: Currently selected Sound can be
set as a Ring Tune.
] Delete: Currently selected Sound can be deleted.
] Edit Title: Title of currently selected Sound can be
edited.
]Delete All: All Sounds can be deleted.
Note
n
Sounds supplied as default can only be used under the Set
As Ring Tone mode.
5050
Graphics Menu 4.3
The left soft key [Options] will bring up the following
option.
] Send Via Multimedia Message: Downloaded image
can be sent via MMS.
] Set As Wallpaper: Currently selected Picture can be
set as a Wallpaper.
] Delete: Currently selected Picture can be deleted.
] Edit Title: Title of currently selected Picture can be
edited.
] Delete All: All Pictures can be deleted.
n
Note
Pictures supplied as default can only be used under the Set
As Wallpaper mode.
Page 51
Multimedia Contents Menu 4.4
You can view, delete, or control downloaded contents.
You can get animation from WAP sites, MMS or SMS.
While you’re checking each content, you can send it
via SMS or MMS, edit or delete it.
View Online Album Menu 4.5
The Online Album is a space to keep the user’s photos
and MMS data(pictures). We can get access to the
View Online Album by mobile phone. Also, you can
connect to the album on the Internet through the WAP
address.
The WAP address is as follows:
http://wap:8582/photoalbum.wml
Media Services
5151
Page 52
Internet
You can access various WAP(Wireless Application
Protocol) services such as banking, news, weather
reports and flight information. These services are
specially designed for mobile phones and they are
maintained by the WAP service providers.
Check the availability of WAP services, pricing and
tariffs with your network operator and/or the service
provider whose service you wish to use. Service
providers will also give you instructions on how to use
their services.
Please contact your service provider to open an
Internet account. To use the Web Browser, you must
indicate your phone number via the Own Number
menu option (See page
To launch the browser in standby mode, press and hold
down the
Once connected, the homepage is displayed. All web
content is determined by the service provider.
You can open any WWW page by entering its URL
address.
To exit the browser at any time, press the
The idle screen is displayed.
5252
key.
62 for further details.)
key.
Navigating with the WAP Browser
You can surf the Internet using either the phone keys
or the WAP Browser menu.
Using the Phone Keys
When surfing the Internet, the phone keys function
differently from the phone mode.
KeyDescription
Up / down navigation
Key
Scroll each line of the content area
Using the WAP Browser Menu
There are various menu options available when surfing
the Wireless Web.
n
Note
The WAP Browser menus may vary, depending on your
version of the browser.
Page 53
Internet
GoRogers Menu 5.1
Connect to a homepage. The homepage may be the
site which is defined in the activated profile. It will be
defined by the Service Provider if you have not defined
it in the activated profile.
Access Point Menu 5.2
A profile is the network information used to connect to
the Internet.
The options are:
• Activate: Activates the selected network.
• Settings: View the various items of the current
profile.
• Rename: Revises the name on the profile.
Cache Settings Menu 5.3
The information or services you have accessed are
stored in the cache memory of the phone.
Clear Cache (Menu 5.3.1)
Removes all content saved in cache.
Cache Check (Menu 5.3.2)
Sets a value whether a connection attempt is made
through cache or not.
Note
n
Cache is a buffer memory, which is used to store data
temporarily.
Security Certificates Menu 5.4
Shows a list of the available certificates.
WAP Information Menu 5.5
The WAP Browser version is displayed.
53
Page 54
Sounds
Download Ring Tunes Menu 6.1.
Download the ringtone from the selected URL address.
Ringtones Menu 6.2
This option allows you to select the required ring
melody. You can choose between many different
melodies. If you have any downloaded sounds from the
Internet or any received ring tone messages, you can
view the list in this menu.
Volume Menu 6.3
]
Ringtone: To set the volume level for the ringing tones.
]
Key Tone: To set the volume level for keypad tones.
]
Call: This can adjust the volume level.
]
Headset: When using the Headset, volume level can
be adjusted.
]
Handsfree: When using the Handsfree, volume level
can be adjusted.
Ring Alert Type Menu 6.4
This option determines the incoming call notification
54
mode. You can select from Ring, Ring and Vibrate and
Vibrate then Ring.
Message Alert Tones Menu 6.5
Select the alert tone for messages.
n
Note
Muting soft key only changes muting for this specific menu.
Key Tones Menu 6.6
This menu option allows you to select a tone that the
phone sounds when you press a key. You can select an
option from Beep and Voice.
n
Note
The Voice option provides voice enunciation of each
number typed in from the keypad. Beep is the default tone
for all other keystrokes. Keypad tone and volume must be
enabled as well as phone muting turned off to hear Voice
option
Voice Recording Menu 6.7
For further details, see page 56 (Menu 7.3).
Page 55
Tools
Alarm Clock Menu 7.1
Set the alarm to ring at a specific time. In the Alarm
Clock menu, the following options are available:
On: Set the time (hour and minute) for activating the
alarm.
1. Go to Alarm Clock
2. Select [On] by pressing the right/left navigation keys.
3. If you want to set the time for activating the alarm,
press the down navigation key.
4. Enter the required time, press the down navigation key.
5. The following options are available.
• Once: The alarm rings only once and is then deactivated.
• Daily: The alarm rings every day at the same time.
• Weekly: The alarm rings every week on the same
day and at the same time.
• Monthly: The alarm rings every month on the same
day and at the same time.
6. Allows you to select the alarm melody by using the
right / left navigation keys.
7. Press the left soft key [Set].
Off: Cancel the alarm.
Notice
n
If this option is set to On, the alarm will ring at the specified
time, even when the phone is switched off. To stop the
alarm when it rings the right soft key [Quit].
Calendar Menu 7.2
When you enter this menu a calendar will be
displayed. Top of the screen indicates sections for
date. A square cursor is used to locate a particular
day. If a schedule or memo has been entered on a
particular day, that date will appear in a different
colour. This function helps to remind you of the
schedule and memo. The phone will sound an alarm
tone if it has been set for a specific note.
For changing the day, month and year.
KeyDescription
Up / down
navigation key
Left / right
navigation key
Weekly
Daily
55
Page 56
Tools
n Note
Schedule editing options are available only after an
initial appointment has been entered into your calendar.
If an entry has been made, then a calendar icon appears
on the idle display on the date of the appointment, and,
when viewing the calendar, a date with appointments
is highlighted or shaded differently from dates with no
appointments.
]
View: Press the left soft key [Options] to delete or
edit the note you selected.
]
Edit: Allows you to edit the schedule.
]
Delete: Allows you to delete the schedule.
]
Add New: You can edit maximum of 30 characters
and create up to 30 notes.
]
Calendar: Allows you to consult the calendar.
]
Scheduler Tone: The phone can sound an alarm
tone when the scheduled date for an event has been
reached with this option.
]
View All Schedules: Shows the notes that are set
for all days. Use the up / down navigation keys to
browse through the note lists. You can use the menu
by press the left soft key [Options].
]
Go To Date: Allows you to jump to a specific date.
56
]
Delete Past: Delete past schedule event that has
already been notified.
]
Delete All: Delete all schedules. You are asked to
confirm your action.
n Note
You can see Edit, Delete,View all schedules, Delete past
and Delete all menus dependent on setting of the schedule.
Voice Recording Menu 7.3
Allows you to record a memo. You can record up to 3
voice messages with each message up to 30 seconds.
1. Once recording is started, the message
‘Recording...’ and the remaining time are displayed.
n
Note
If all memo locations are full, you must delete an old memo
before recording a new one.
2. If you want to finish recording, press the left soft
key [Save].Once recording is saved it will display
with date and time of recording in the Voice
Recording menu display.
]
Play: Allows you to play back all memos recorded,
starting with the most recent memo.
Page 57
]
Delete: Allows you to delete a specific memo. All
memos recorded are played back, starting with the
most recent one.
]
Record New: Allows you to record a memo.
]
Rename: Allows you to rename a specific memo.
]
Send Via Multimedia Message: Sends the selected
voice memo by MMS.
]
Delete All: Allows you to delete all memos.
Calculator Menu 7.4
Using this feature, you can use the phone as a
calculator. The calculator provides the basic
arithmetic functions: addition, subtraction,
multiplication and division.
Using the Calculator
1. Enter the first number using the numeric keys.
n
Notice
To make a number negative, press the
key prior to entering a number.
2. Use the navigation keys to select a sign for
calculation.
(minus symbol)
Tools
Note
n
To include a decimal point, press the
key.
3. To calculate the result, press the left soft key
[Result] or key.
Memo Menu 7.5
To write, edit and delete a memo, proceed as follows.
1. Press the left soft key [Add].
2. Input the memo and press the left soft key
[Options].
The following options are available.
]
Save: Allows you to save the memo.
]
T9 Languages: Allows you to select the T9 language
to use in memo.
]
Exit Editor: Allows you to exit in memo editor.
Or
1. Select a Memo.
2. Press the left soft key [Options].
The following options are available.
]
View: Allows you to view the memo.
]
Delete: Allows you to delete the memo.
57
Page 58
Tools
Edit: If you select a memo that already exists, you
]
can press the left soft key [Options → Edit] to edit the
memo displayed.
]
Add New: Add a new memo, up to 20 memos and 40
characters per each memo.
]
Delete All: Allows you to delete all memos. You are
asked to confirm your action.
World Time Menu 7.6
Allows you to check the major cities around the world,
using the left/right navigation keys.
The screen shows the city name, current date and
time.
To select the time zone in which you are located,
proceed as follows:
1. Select the city corresponding to your time zone by
pressing the left/right navigation keys once or more
times. The local date and time are displayed.
2. Press the left soft key [Options].
3. If you want to set, press the
4. If you want to set Daylight Savings, press the
key in Options menu.
key.
Note
n
The time zone setting of each city in World Time menu may
be affected by network condition.
Unit Converter Menu 7.7
This converts any measurement into a unit you want.
There are four types that can be converted into units:
Length, Surface, Weight and Volume.
1. You can select one of four unit types by pressing the left soft key [Unit].
2. Select the standard value by using the left/right
navigation keys.
3. Select the unit you want to convert by pressing the
up/down navigation keys.
4. You can check the converted value for the unit you
want. Also, you can input a decimal number by
pressing the key.
58
Page 59
Address Book
You can store phone numbers and their corresponding
names in the memory of your SIM card. In addition,
you can store up to 255 numbers and names in the
phone memory. The SIM card and phone memories,
although physically separate, are used as if they were
a single entity, called the Address Book.
Contact List Menu 8.1
1. Press the left soft key [Menu].
2. Press , .
n
Note
You can also access the Address Book on the idle screen
by pressing the down on the navigation key.
3. If you want to edit, delete or copy an entry, select
[Options].
• View Detail: To view in detail the selected name.
• Delete: You can delete an entry.
• Write Text Message: You can write a text message.
For further details, see page 39.
• Write Multimedia Message: You can write a
multimedia message. For futher details, see page 41.
• Edit: You can edit the name, mobile number, home
number, office number, E-mail, group and memo by
pressing the left soft key [Select].
• Copy To Phone: You can copy an entry from SIM to
phone.
• Voice Tag: Allows you to set a voice tag to voice dial
the entry.
4. Once you have found the required entry, press the
to dial the number.
New Contact Menu 8.2
You can add an address book entry by using this
function. Phone memory capacity is 255 entries. SIM
card memory capacity depends on the cellular service
provider. Each entry can have up to 20 characters
and save characters in the SIM card. The number of
characters is dependent on the SIM.
1. Press the left soft key [Menu].
2. Press
3. You can add new Address book entries to SIM
memory or the Address book memory. To select the
memory, go to Set Memory (Menu 8.8). (Refer to
page 62)
, and press the left soft key [Select].
59
Page 60
Address Book
Speed Dials Menu 8.3
You can assign the following keys,
a name list entry. You can call directly by pressing an
assigned key for 2-3 seconds.
1. Press the left soft key [Menu].
2. Press
, .
3. If you want to add a number to speed dial, select an
empty slot <Empty>. Then, you can search the name
from the Address Book.
4. Select the name from the speed dial. You can
change and delete the name. In addition, you can
call by this number, write a text message or a
multimedia message.
to with
Voice Tag List Menu 8.4
You can see all the phone numbers which contain
voice tags. You can also call directly by pressing
the
key. After selecting the phone number by using
the up / down navigation keys, press the left soft key
[Options] and it will offer the following submenus:
]
Listen: You can play back the voice tag attached to a
phone number.
]
Change: You can change the voice tag attached to a
phone number.
]
Remove: You can delete the voice tag attached to a
phone number.
]
Call: You can call by selecting this submenu.
]
Add New Voice Tag: You can add a new voice tag to
a phone number.
]
Remove All: You can delete all the voice tag attached
to a phone number.
n
Note
The voice tag can only be attached to the main number
which you set. If you change your main number, the voice
tag will belong to the new main number. You cannot attach
a voice tag to your mobile number, home number and office
number simultaneously. You can add a voice tag to a phone
number in the SIM card. The voice tag can be erased if you
remove or change the SIM card.
60
Page 61
Address Book
Caller Groups Menu 8.5
There are 7 predefined groups as well as one
additional group labeled Others where you can create
your own lists.
1. You can set the phone to ring in a specific way and
display a preselected graphic icon when a particular
person calls you.
2. Scroll to Caller Groups then press the left soft key
[Select] to enter this menu.
3. Every Group list will be displayed: Family, VIP,
Friends, Colleague, Group 1, Group 2, Others.
4. Select the Group name that you want to manage by pressing the left soft key [Options].
5. You will see the following submenus under the predefined groups except for the Others group.
• Members List: Allows you to see the member list
in the group.
• Group Ring Tone: Allows you to select the ring tone
to be used when you receive a voice phone call
from a person in the group.
• Group Icon: Allows you to select the graphic icon
to be displayed when you receive a call from a
person in the group.
• Add Member: Allows you to add the member to
the group.
• Delete Member: Allows you to delete the member
in the group.
• Rename: Allows you to assign a name to the group.
Copy All Menu 8.6
You can copy or move entries from the SIM card
memory to the phone memory and vice versa.
SIM To Phone (Menu 8.6.1)
You can copy all the entries from the SIM card to
phone memory.
Phone To SIM (Menu 8.6.2)
You can copy all the entries from the phone memory to
the SIM card.
6161
Page 62
Address Book
The following options are available:
]
Keep Original: When copying, Original Dial Number
is kept.
]
Delete Original: When copying, Original Dial Number
will be erased.
Delete All Menu 8.7
You can delete all SIM and Phone book entries, as well
as your Voice tags. With the exception of Voice tags,
you will need to enter your security code to delete your
SIM and Phone book entries.
Press the
key to return to the standby mode.
Set Memory Menu 8.8
Scroll to highlight the Set Memory option, then press
the left soft key [Select].
] If you select Variable when adding entry, the phone
will ask where to store the information.
] If you select SIM or Phone, the phone will store an
entry to the SIM or the phone.
62
:Shown only if supported by SIM card
*
Information Menu 8.9
Memory Status
You can check how many names and numbers are
stored in the Address Book (SIM card and phone
memories).
Own Number (Menu 8.9.2)
Allows you to display your phone number in the SIM
card.
(Menu 8.9.1)
Page 63
Settings
You can use the Sound Settings feature to customize
various settings, such as the:
] Ring melody, volume and type
] Sounds made when you press a key, make an error
or receive a message
Display Menu 9.1
You can change the background image and the display
style for Menu Mode according to your preference.
My Wallpaper (Menu 9.1.1)
This option allows you to change the background
image (wallpaper) to be displayed in idle mode.
To change the background image, proceed as follows.
1. Scroll through the list by pressing the left or right
navigation key.
You have various preset images available. You can
also select the blank background or any images
downloaded from the Internet.
2. Press the left soft key [Select] when the required
image is highlighted.
The selected image is displayed.
Backlight (Menu 9.1.2)
You can select whether or not the phone uses the
backlight. A marginal increase in the standby / talk
time can be achieved by turning the backlight off.
It turns off if no key is pressed within one minute.
• 10 Seconds turns the backlight off 10 seconds after
the last key was pressed.
• 30 Seconds turns the backlight off 30 seconds after
the last key was pressed.
• 60 Seconds turns the backlight off 60 seconds after
the last key was pressed.
Contrast (Menu 9.1.3)
This option allows you to adjust the contrast of the LCD
screen by pressing the navigation key.
6363
Page 64
Settings
Screen Saver (Menu 9.1.4)
The phone automatically activates a screen saver
after a certain length of time when none of the phone
functions have been used, see Backlight (Menu.9.1.2)
on page 63.
Power On Sound (Menu 9.1.5)
If you set to On your phone will sound the specific
sound when you switch it on/off.
Languages (Menu 9.1.6)
You can select the display language. When the
language option is set to Automatic, the language is
automatically
the SIM card used. English will be set if the language
on the SIM card is not supported in the phone.
selected according to the language of
Menu Style (Menu 9.1.7)
This option allows you to select the menu display style.
You can choose either Icon style or List style.
64
Date & Time Menu 9.2
Set Date (Menu 9.2.1)
Allows you to enter the day, month and year. You can
change the date format via the Date Format menu
option.
Date Format (Menu 9.2.2)
YYYY/MM/DD(year/month/day)
DD/MM/YYYY(day/month/year)
MM/DD/YYYY(month/day/year)
Set Time (Menu 9.2.3)
Allows you to enter the current time. You can choose
the time format via the Time Format menu option.
Time Format (Menu 9.2.4)
24 Hours / 12 Hours
Page 65
Auto Update (Menu 9.2.5)
Select On to set the phone to automatically update the
time and date according to the current time zone.
Call Settings Menu 9.3
To change the settings for call diverting:
Call Forwarding (Menu 9.3.1)
When this network service is activated, you can direct
your incoming calls to another number, for example, to
your voice mailbox number. For details, contact your
service provider.
The following options are available:
] All Voice Calls: Diverts voice calls unconditionally.
] If Busy: Diverts voice calls when the phone is in use.
]
If No Reply: Diverts voice calls which you do not
answer.
]
If Out Of Reach: Diverts voice calls when the phone
is switched off or out of coverage.
Settings
]
All Data Calls: Diverts to a number with a PC
connection unconditionally.
]
All Fax Calls: Diverts to a number with a fax
connection unconditionally.
• Activate: Activates the corresponding service.
- Number: Inputs the number for diverting.
• Cancel: Cancels the corresponding service.
• View Status: Checks the status of the service.
]
Cancel All: Cancels all call divert service.
Answer Mode (Menu 9.3.2)
Allows you to determine how to answer the phone.
]
Any Key: You can answer an incoming call by
pressing any key, except the
]
Send Key Only: You can answer an incoming call by
only pressing the key.
key.
:Shown only if supported by SIM card
*
6565
Page 66
Settings
Send My Number (Menu 9.3.3)
This network service allows you to set your phone
number to be displayed On or hidden Off from the
person to whom you are calling. Select Set By Network to reset the phone to the setting that you
have agreed upon with your service provider.
Call Waiting (Menu 9.3.4)
The network will notify you of a new incoming call
while you have a call in progress. Select Activate to
request the network to activate call waiting, Cancel to
request the network to deactivate call waiting or View
Status to check if the function is active or not.
Minute Minder (Menu 9.3.5)
This option allows you to specify whether the phone
must beep every minute during an outgoing call to
keep you informed of the length of the call.
Auto Redial (Menu 9.3.6)
Select On, and your phone will make a maximum
of three attempts to connect the call after an
unsuccessful call attempt.
66
:Shown only if supported by SIM card
*
Send DTMF (Menu 9.3.7)
You can send the DTMF (Dual Tone Multi-Frequency)
tones of the number on the display during a call.
This option is helpful for entering a password or
account number when you call an automated system,
like a banking service.
Security Menu 9.4
Various codes and passwords are used to protect
the features of your phone. They are described in the
following sections (see page 22).
PIN Code Request (Menu 9.4.1)
When the PIN code request feature is enabled, you
must enter your PIN each time you switch the phone
on. Consequently, any person who does not have your
PIN cannot use your phone without your approval.
nNote
Before disabling the PIN code request feature, you must
enter your PIN.
Page 67
Settings
The following options are available:
]Enable: You must enter the PIN each time the phone
is switched on.
]Disable: The phone connects directly to the network
when you switch it on.
Phone Lock (Menu 9.4.2)
When the Phone Lock feature is enabled, the phone is
locked and you must enter the phone password each
time the phone is switched on. The password is factory
set to 0000. To change the phone password, refer to
the Change Codes - Security Code menu option [Menu
9.5.6]. Once the correct password has been entered,
you can use the phone until you switch it off.
The following options are available:
When Power On
]Off: You do not need to enter the phone password
when you switch the phone on.
]Always On: You are required to enter the phone
password when you switch the phone on.
]When SIM Changed: Your phone will request
security code only when you change your SIM card.
Immediately
After entering the correct security code, the phone
will lock after going into the idle state. If you want
to disable this phone lock, you should enter the right
security code after pressing the right soft key. If you
power off in the phone lock state, when the phone is
next powered on, the phone is in the lock state.
Auto Key Lock (Menu 9.4.3)
When you enable Automatic key lock, keypad will be
lock automatically on an idle screen after selected
seconds without any key requesting. if you set to Off,
keypad will not be locked automatically.
n
Note
If you want to unlock your phone keypad, press the left soft
key [Unlock] and then press the right soft key. But if you
enabled Automatic key lock before, your phone keypad will
unlock and then after selected seconds the keypad will
lock up again automatically.
67
Page 68
Settings
Call Barring Service (Menu 9.4.4)
Call barring allows you to restrict from making and
receiving calls with your phone. For this function, you
need the barring password, which you can obtain from
your service provider.
The following options are available:
]
All Outgoing: Calls cannot be made.
]
Outgoing International: International calls cannot be
made.
]
Cancel All Barrings: All call barring settings are
deactivated; calls can be made and received normally.
]
Change Password: You can set and change the
call barring password obtained from your service
provider using this option. You must enter the current
password before you can specify a new one. Once
you have entered a new password, you are asked to
confirm it by entering it again.
n
Note
To use Call Barring Service, you must input the network
password. When calls are barred, calls may be possible to
certain emergency numbers in some networks.
68
:Shown only if supported by SIM card
*
Fixed Dial Number (FDN) (Menu 9.4.5)
Allows you to restrict your outgoing calls to selected
phone numbers, if this function is supported by your
SIM card. The PIN2 code is required.
The following options are available:
]
Enable: You can only call phone numbers stored in
the Address Book.You must enter your PIN2.
]
Disable: You can call any number.
]
Number List: You can view the number list saved as
fixed dial number.
n Note
Not all SIM cards have a PIN2. If yo
this menu option is not displayed.
ur SIM card does not,
Change Codes (Menu 9.4.6)
The Change Codes feature allows you to change your
current password to a new one. You must enter the
current password before you can specify a new one.
You can change the access codes: Security Code,
PIN1 Code, PIN2 Code
Page 69
n
Note
PIN: Personal Identification Number.
Connection Menu 9.5
Network Selection (Menu 9.5.1)
The Network Selection feature allows you to indicate
how the network you will use is selected when
roaming outside your home area.
Options are: Automatic, Manual and Preferred.
n
Note
You can select a network other than your home network
only if it has a valid roaming agreement with your home
network.
]Automatic: Allows you to set the phone to
automatically search for and select one of the
cellular networks available in your area. The phone
will be set to Automatic by default.
]Manual: Allows you to select the desired network
manually from a list of networks. If the connection
to the manually selected network is lost, the phone
will sound an error tone and ask you to select a
network again. The selected network must have a
roaming agreement with your home network, that is,
Settings
the operator whose SIM card is in your phone. The
phone lets you select another network if the phone
fails to access the selected network. If you switch
off the phone, the phone will be reset to Automatic.
]Preferred: You can set a list of preferred networks
the handset should attempt to register with first,
before attempting to register to any other networks.
This list is created from the handset’s predefined list
of known networks.
GPRS Attach (Menu 9.5.2)
If you select Power On and you are in a network that
supports packet data, the phone registers to the GPRS
network and sending short messages will be done via
GPRS. Also, starting an active packet data connection,
for example, to send and receive e-mail, is quicker. If
you select When Needed, the phone will use a packet
data connection only if you start an application or
action that needs it. The GPRS connection is closed
after it is not used by any application.
Note
n
If there is no GPRS coverage and you have chosen Power
On, the phone will periodically try to establish a packet data
connection.
69
Page 70
Settings
Access Point (Menu 9.5.3)
This feature sets the Profile during the WAP
connections. Please see page 51 for further detail.
The Profile menu under the Access Point feature will
display Add, Delete and Editor options, but the reason
why Activate option is not available is that there is no
way of knowing whether WAP will be used to activate
the content.
Reset Access Point (Menu 9.5.4)
This allows Profile information to be restored to
original setting. For example, this option will restore
the Profile that has been deleted by the Delete All
selection from the Access Point (Menu 5.2) submenu.
Reset Setting Menu 9.6
You can easily reset your phone to its default
configuration. To do so, proceed as follows.
1. Select the Reset Setting menu option.
2. Enter the 4-digit phone password.
n
Note
The password is preset to 0000.
70
Page 71
Q&A
Please check to see if any problems you have
encountered with the phone are described in this
section before taking the phone in for a service or
calling your service provider.
How do I view the list of outgoing calls, incoming
Q
calls and missed calls?
Press the
A
How do I clear all call history?
Q
Press the left soft key [Menu] and then the
A
Why is the connection inconsistent or not audible
Q
in certain areas?
When frequency environment is unstable in a
A
certain area, connection may be inconsistent and
not audible. Relocate to another area and try again.
key.
keys.
Why is the connection not consistent or abruptly
Q
disconnects even when established?
When frequency is unstable or weak or if there are
A
too many users, connection may be cut off even
after it was established. Please try again later or
attempt after relocating to other areas.
Why does the LCD not turn on?
Q
Remove the battery and turn on the power after
A
placing it back on. If there is no change, fully charge
the battery and try again.
Why is there an echo when a connection is made
Q
with certain telephones in a certain area?
This is called the ‘Echo Phenomenon’, where it
A
occurs if connection volume is too high or caused
by special properties (semi electronic telephone
exchange) of the equipment on the other end.
7171
Page 72
Q&A
Why does the phone heat up?
Q
The phone may get hot when there is a very
A
long call duration or when games are played or
even when surfing the Internet for a long time.
This has no effect upon the life of the product or
performance.
Why is there no ring tone, but only a blinking LCD
Q
screen?
Phone may be set to ‘Vibration All’ or in ‘Silent All'
A
mode. In the Sound menu, please select Volume →
Ringtone → Volume 1 ~ Volume 5.
Why does the battery life get shorter in standby
Q
mode?
The battery is worn out. As time passes, the battery
A
life gradually becomes shorter. If the battery
lasts about half the amount of time as when first
purchased, it’s time to purchase a new battery.
Why does the battery run out so quickly during
Q
normal use?
It is due to the user environment or a large number
A
of calls or weak signal.
72
Why is no number dialed when you recall a Address
Q
Book entry?
Check that the number has been stored correctly
A
by using the address book Search feature. Re-store
them, if necessary.
Why can’t my correspondent reach me?
Q
Is your phone switched on (
A
than three seconds)? Are you accessing the right
cellular network? Or, you may have set an incoming
call barring option.
I cannot find the lock, PIN or PUK code. What is my
Q
password?
The default lock code is ‘0000’. If you forget or lose
A
the lock code, contact your phone dealer. If you
forget or lose a PIN or PUK code, or if you have not
received such a code, contact your network service
provider.
) pressed for more
Page 73
Accessories
There are a variety of accessories available for your
mobile phone. You can select these options according
to your personal communication requirements. Consult
your network service provider for availability.
Travel Adapter
This adapter allows you to
charge the battery.
Battery (7 60 mAh)
Standard battery is available.
Vehicle Power Adapter
You can operate the phone and
trickle charge the phone battery
from your vehicle by using the
vehicle power adapter. It takes
3 hours to charge a completely
discharged battery.
Headset
Connects to your phone,
allowing hands-free operation.
Includes earpiece, microphone
and integrated call answer/
termination button.
Data Cable Kit
Connects your phone to a PC.
Cable can be used for GPRS
modem connectivity or PC
Synch of your calendar and
contacts.
73
Page 74
Safety Guidelines
TIA Safety Information
Provided herein is the complete TIA Safety Information
for Wireless Handheld phones. Inclusion of the text
covering Pacemakers, Hearing Aids and Other Medical
Devices is required in the owner’s manual for CTIA
Certification. Use of the remaining TIA language is
encouraged when appropriate.
Exposure to Radio Frequency Signal
Your wireless handheld portable telephone is a lowpower radio transmitter and receiver. When it is ON,
it receives and also sends out radio frequency (RF)
signals.
In August, 1996, the Federal Communications
Commissions (FCC) adopted RF exposure guidelines
with safety levels for handheld wireless phones. Those
guidelines are consistent with the safety standards
previously set by both U.S. and international standards
bodies:
ANSI C95.1 (1992) *
NCRP Report 86 (1986)
ICNIRP (1996)
7474
Those standards were based on comprehensive
and periodic evaluations of the relevant scientific
literature. For example, over 120 scientists, engineers
and physicians from universities, government health
agencies and industry reviewed the available body of
research to develop the ANSI Standard (C95.1).
* American National Standards Institute; National
Council on Radiation Protection and Measurements;
International Commission on Non-Ionizing Radiation
Protection
The design of your phone complies with the FCC
guidelines (and those standards).
Antenna Care
Use only the supplied or an approved replacement
antenna. Unauthorized antennas, modifications or
attachments could damage the phone and may violate
FCC regulations.
Phone Operation
NORMAL POSITION: Hold the phone as you would any
other telephone with the antenna pointed up and over
your shoulder.
Page 75
Safety Guidelines
Tips on Efficient Operation
For your phone to operate most efficiently:
]
Do not touch the antenna unnecessarily when the
phone is in use. Contact with the antenna affects
call quality and may cause the phone to operate at a
higher power level than otherwise needed.
Driving
Check the laws and regulations on the use of wireless
phones in the areas where you drive. Always obey
them. Also, if using your phone while driving, please:
]
Give full attention to driving — driving safely is your
first responsibility;
]
Use hands-free operation, if available;
]
Pull off the road and park before making or
answering a call if driving conditions so require.
Electronic Devices
Most modern electronic equipment is shielded from
RF signals. However, certain electronic equipment
may not be shielded against the RF signals from your
wireless phone.
Pacemakers
The Health Industry Manufacturers Association
recommends that a minimum separation of six (6’)
inches be maintained between a handheld wireless
phone and a pacemaker to avoid potential interference
with the pacemaker. These recommendations are
consistent with the independent research by and
recommendations of Wireless Technology Research.
Persons with pacemakers:
]
Should ALWAYS keep the phone more than six inches
from their pacemaker when the phone is turned ON;
]
Should not carry the phone in a breast pocket.
]
Should use the ear opposite to the pacemaker to
minimize the potential for interference.
]
If you have any reason to suspect that interference is
taking place, turn your phone OFF immediately.
Hearing Aids
Some digital wireless phones may interfere with some
hearing aids. In the event of such interference, you
may want to consult your service provider.
75
Page 76
Safety Guidelines
Other Medical Devices
If you use any other personal medical device, consult
the manufacturer of your device to determine if they
are adequately shielded from external RF energy. Your
physician may be able to assist you in obtaining this
information.
Turn your phone OFF in health care facilities when
any regulations posted in these areas instruct you
to do so. Hospitals or health care facilities may be
using equipment that could be sensitive to external RF
energy.
Vehicles
RF signals may affect improperly installed or
inadequately shielded electronic systems in motor
vehicles. Check with the manufacturer or its
representative regarding your vehicle.
You should also consult the manufacturer of any
equipment that has been added to your vehicle.
Posted Facilities
Turn your phone OFF in any facility where posted
notices so require.
76
Aircraft
FCC regulations prohibit using your phone while in the
air. Turn your phone OFF before boarding an aircraft.
Blasting Areas
To avoid interfering with blasting operations, turn
your phone OFF when in a ‘blasting area’ or in areas
posted: ‘Turn off two-way radio’. Obey all signs and
instructions.
Potentially Explosive Atmosphere
Turn your phone OFF when in any area with a
potentially explosive atmosphere and obey all signs
and instructions. Sparks in such areas could cause
an explosion or fire resulting in bodily injury or even
death.
Areas with a potentially explosive atmosphere are
often, but not always, marked clearly. Potential areas
may include: fueling areas (such as gasoline stations);
below deck on boats; fuel or chemical transfer or
storage facilities; vehicles using liquefied petroleum
gas (such as propane or butane); areas where the air
contains chemicals or particles (such as grain, dust or
metal powders); and any other area where you would
normally be advised to turn off your vehicle engine.
Page 77
Safety Guidelines
For Vehicles Equipped with an Air Bag
An air bag inflates with great force. DO NOT place
objects, including either installed or portable wireless
equipment, in the area over the air bag or in the air bag
deployment area. If in-vehicle wireless equipment is
improperly installed and the air bag inflates, serious
injury could result.
FDA Consumer Update
The U.S. Food and Drug Administration’s Center for
Devices and Radiological Health Consumer Update on
Mobile Phones.
1. Do wireless phones pose a health hazard?
The available scientific evidence does not show
that any health problems are associated with using
wireless phones. There is no proof, however, that
wireless phones are absolutely safe. Wireless
phones emit low levels of radiofrequency energy
(RF) in the microwave range while being used. They
also emit very low levels of RF when in the standby
mode. Whereas high levels of RF can produce
health effects (by heating tissue), exposure to low
level RF that does not produce heating effects
causes no known adverse health effects. Many
studies of low level RF exposures have not found
any biological effects. Some studies have suggested
that some biological effects may occur, but such
findings have not been confirmed by additional
research. In some cases, other researchers have
had difficulty in reproducing those studies, or in
determining the reasons for inconsistent results.
77
Page 78
Safety Guidelines
2. What is the FDA’s role concerning the safety
of wireless phones?
Under the law, the FDA does not review the safety
of radiation-emitting consumer products such as
wireless phones before they can be sold, as it does
with new drugs or medical devices. However, the
agency has authority to take action if wireless
phones are shown to emit radiofrequency energy
(RF) at a level that is hazardous to the user. In such
a case, the FDA could require the manufacturers of
wireless phones to notify users of the health hazard
and to repair, replace or recall the phones so that
the hazard no longer exists.
Although the existing scientific data do not justify
FDA regulatory actions, the FDA has urged the
wireless phone industry to take a number of steps,
including the following:
]
Support needed research into possible biological
effects of RF of the type emitted by wireless
phones;
]
Design wireless phones in a way that minimizes
any RF exposure to the user that is not necessary
for device function; and
78
]
Cooperate in providing users of wireless phones
with the best possible information on possible
effects of wireless phone use on human health.
The FDA belongs to an interagency working group
of the federal agencies that have responsibility for
different aspects of RF safety to ensure coordinated
efforts at the federal level. The following agencies
belong to this working group:
●
National Institute for Occupational Safety and
Health
●
Environmental Protection Agency
●
Occupational Safety and Health Administration
●
National Telecommunications and Information
Administration
The National Institutes of Health participates in
some interagency working group activities as well.
The FDA shares regulatory responsibilities for
wireless phones with the Federal Communications
Commission (FCC). All phones that are sold in
the United States must comply with FCC safety
guidelines that limit RF exposure. The FCC relies
on the FDA and other health agencies for safety
questions about wireless phones.
Page 79
Safety Guidelines
The FCC also regulates the base stations that the
wireless phone networks rely upon. While these
base stations operate at higher power than do the
wireless phones themselves, the RF exposures that
people get from these base stations are typically
thousands of times lower than those they can get
from wireless phones. Base stations are thus not
the subject of the safety questions discussed in this
document.
3. What kinds of phones are the subject of this
update?
The term ‘wireless phone’ refers here to handheld
wireless phones with built-in antennas, often called
‘cell’, ‘mobile’ or ‘PCS’ phones. These types of
wireless phones can expose the user to measurable
radiofrequency energy (RF) because of the short
distance between the phone and the user’s head.
These RF exposures are limited by FCC safety
guidelines that were developed with the advice
of the FDA and other federal health and safety
agencies. When the phone is located at greater
distances from the user, the exposure to RF is
drastically lower because a person’s RF exposure
decreases rapidly with increasing distance from
the source. The so-called ‘cordless phones,’ which
have a base unit connected to the telephone wiring
in a house, typically operate at far lower power
levels, and thus produce RF exposures far below the
FCC safety limits.
4. What are the results of the research done
already?
The research done thus far has produced conflicting
results, and many studies have suffered from flaws
in their research methods. Animal experiments
investigating the effects of radiofrequency energy
(RF) exposures characteristic of wireless phones
have yielded conflicting results that often cannot be
repeated in other laboratories. A few animal studies,
however, have suggested that low levels of RF could
accelerate the development of cancer in laboratory
animals. However, many of the studies that showed
increased tumor development used animals that had
been genetically engineered or treated with cancercausing chemicals so as to be pre-disposed to develop
cancer in the absence of RF exposure. Other studies
exposed the animals to RF for up to 22 hours per day.
These conditions are not similar to the conditions
under which people use wireless phones, so we don’t
’
79
Page 80
Safety Guidelines
know with certainty what the results of such studies
mean for human health.
Three large epidemiology studies have been published
since December 2000. Between them, the studies
investigated any possible association between the use
of wireless phones and primary brain cancer, glioma,
meningioma, or acoustic neuroma, tumors of the brain
or salivary gland, leukemia, or other cancers. None of
the studies demonstrated the existence of any harmful
health effects from wireless phone RF exposures.
However, none of the studies can answer questions
about long-term exposures, since the average period of
phone use in these studies was around three years.
5. What research is needed to decide whether
RF exposure from wireless phones poses a
health risk?
A combination of laboratory studies and
epidemiological studies of people actually using
wireless phones would provide some of the data that
are needed. Lifetime animal exposure studies could be
completed in a few years. However, very large numbers
of animals would be needed to provide reliable proof of
a cancer promoting effect if one exists. Epidemiological
studies can provide data that is directly applicable
80
to human populations, but 10 or more years followup may be needed to provide answers about some
health effects, such as cancer. This is because the
interval between the time of exposure to a cancercausing agent and the time tumors develop — if they
do — may be many, many years. The interpretation
of epidemiological studies is hampered by difficulties
in measuring actual RF exposure during day-to-day
use of wireless phones. Many factors affect this
measurement, such as the angle at which the phone is
held, or which model of phone is used.
6. What is the FDA doing to find out more about
the possible health effects of wireless phone
RF?
The FDA is working with the U.S. National Toxicology
Program and with groups of investigators around the
world to ensure that high priority animal studies are
conducted to address important questions about the
effects of exposure to radiofrequency energy (RF).
The FDA has been a leading participant in the World
Health Organization International Electromagnetic
Fields (EMF) Project since its inception in 1996. An
influential result of this work has been the development
of a detailed agenda of research needs that has driven
Page 81
Safety Guidelines
the establishment of new research programs around
the world. The project has also helped develop a series
of public information documents on EMF issues.
The FDA and the Cellular Telecommunications &
Internet Association (CTIA) have a formal Cooperative
Research and Development Agreement (CRADA) to do
research on wireless phone safety. The FDA provides
the scientific oversight, obtaining input from experts
in government, industry and academic organizations.
CTIA-funded research is conducted through contracts
with independent investigators. The initial research will
include both laboratory studies and studies of wireless
phone users. The CRADA will also include a broad
assessment of additional research needs in the context
of the latest research developments around the world.
7. How can I find out how much radio frequency
energy exposure I can get by using my
wireless phone?
All phones sold in the United States must comply with
Federal Communications Commission (FCC) guidelines
that limit ra dio frequency energy (RF) exposures.
The FCC established these guidelines in consultation
with the FDA and the other federal health and safety
agencies. The FCC limit for RF exposure from wireless
telephones is set at a Specific Absorption Rate (SAR)
of 1.6 watts per kilogram (1.6 W/kg). The FCC limit is
consistent with the safety standards developed by
the Institute of Electrical and Electronic Engineering
(IEEE) and the National Council on Radiation Protection
and Measurement. The exposure limit takes into
consideration the body’s ability to remove heat from
the tissues that absorb energy from the wireless phone
and is set well below levels known to have effects.
Manufacturers of wireless phones must report the RF
exposure level for each model of phone to the FCC. The
FCC website (http://www.fcc.gov/oet/ rfsafety) gives
directions for locating the FCC identification number on
your phone so you can find your phone’s RF exposure
level in the online listing.
8. What has the FDA done to measure the radio
frequency energy coming from wireless
phones?
The Institute of Electrical and Electronic Engineers
(IEEE) is developing a technical standard for
measuring the radio frequency energy (RF)
exposure from wireless phones and other wireless
handsets with the participation and leadership
of FDA scientists and engineers. The standard,
81
Page 82
Safety Guidelines
‘Recommended Practice for Determining the
Spatial-Peak Specific Absorption Rate (SAR) in
the Human Body due to Wireless Communications
Devices: Experimental Techniques,’ sets forth the
first consistent test methodology for measuring
the rate at which RF is deposited in the heads
of wireless phone users. The test method uses
a tissue-simulating model of the human head.
Standardized SAR test methodology is expected to
greatly improve the consistency of measurements
made at different laboratories on the same phone.
SAR is the measurement of the amount of energy
absorbed in tissue, either by the whole body or a
small part of the body. It is measured in watts/kg (or
milliwatts/g) of matter. This measurement is used to
determine whether a wireless phone complies with
safety guidelines.
9. What steps can I take to reduce my exposure
to radiofrequency energy from my wireless
phone?
If there is a risk from these products — and at this
point we do not know that there is — it is probably
very small. But if you are concerned about avoiding
even potential risks, you can take a few simple
82
steps to minimize your exposure to radiofrequency
energy (RF). Since time is a key factor in how much
exposure a person receives, reducing the amount
of time spent using a wireless phone will reduce RF
exposure.
If you must conduct extended conversations by
wireless phone every day, you could place more
distance between your body and the source of the
RF, since the exposure level drops off dramatically
with distance. For example, you could use a headset
and carry the wireless phone away from your body
or use a wireless phone connected to a remote
antenna.
Again, the scientific data do not demonstrate
that wireless phones are harmful. But if you are
concerned about the RF exposure from these
products, you can use measures like those
described above to reduce your RF exposure from
wireless phone use.
10. What about children using wireless phones?
The scientific evidence does not show a danger
to users of wireless phones, including children
and teenagers. If you want to take steps to lower
exposure to radiofrequency energy (RF), the
Page 83
Safety Guidelines
measures described above would apply to children
and teenagers using wireless phones. Reducing
the time of wireless phone use and increasing the
distance between the user and the RF source will
reduce RF exposure.
Some groups sponsored by other national
governments have advised that children be
discouraged from using wireless phones at
all. For example, the government in the United
Kingdom distributed leaflets containing such a
recommendation in December 2000. They noted
that no evidence exists that using a wireless
phone causes brain tumors or other ill effects.
Their recommendation to limit wireless phone
use by children was strictly precautionary; it was
not based on scientific evidence that any health
hazard exists.
11. What about wireless phone interference
with medical equipment?
Radio frequency energy (RF) from wireless phones
can interact with some electronic devices. For this
reason, the FDA helped develop a detailed test
method to measure electromagnetic interference
(EMI) of implanted cardiac pacemakers and
defibrillators from wireless telephones. This test
method is now part of a standard sponsored by
the Association for the Advancement of Medical
instrumentation (AAMI). The final draft, a joint
effort by the FDA, medical device manufacturers
and many other groups, was completed in late
2000. This standard will allow manufacturers to
ensure that cardiac pacemakers and defibrillators
are safe from wireless phone EMI.
The FDA has tested hearing aids for interference
from handheld wireless phones and helped
develop a voluntary standard sponsored by the
Institute of Electrical and Electronic Engineers
(IEEE). This standard specifies test methods and
performance requirements for hearing aids and
wireless phones so that no interference occurs
when a person uses a ‘compatible’ phone and a ‘
compatible’ hearing aid at the same time. This
standard was approved by the IEEE in 2000.
The FDA continues to monitor the use of wireless
phones for possible interactions with other
medical devices. Should harmful interference be
found to occur, the FDA will conduct testing to
assess the interference and work to resolve the
problem.
83
Page 84
Safety Guidelines
12. Where can I find additional information?
For additional information, please refer to the
following resources:
FDA web page on wireless phones
(http://www.fda.gov/cdrh/phones/index.html)
Federal Communications Commission (FCC) RF
Safety Program
(http://www.fcc.gov/oet/rfsafety)
International Commission on Non-lonizing
Radiation Protection (http://www.icnirp.de)
World Health Organization (WHO) International
EMF Project (http://www.who.int/emf)
National Radiological Protection Board (UK)
(http://www.nrpb.org.uk/)
84
Consumer Information on SAR
(Specific Absorption Rate)
This Model Phone Meets the Government’s
Requirements for Exposure to Radio Waves.
Your wireless phone is a radio transmitter and receiver.
It is designed and manufactured not to exceed the
emission limits for exposure to radio frequency
(RF) energy set by the Federal Communications
Commission (FCC) of the U.S. Government. These
limits are part of comprehensive guidelines and
establish permitted levels of RF energy for the
general population. The guidelines are based on
standards that were developed by independent
scientific organizations through periodic and thorough
evaluation of scientific studies. The standards include
a substantial safety margin designed to assure the
safety of all persons, regardless of age and health.
The exposure standard for wireless mobile phones
employs a unit of measurement known as the Specific
Absorption Rate or SAR. The SAR limit set by the FCC is
1.6W/kg. * Tests for SAR
are conducted using standard operating positions
specified by the FCC with
Page 85
Safety Guidelines
the phone transmitting at its highest certified power
level in all tested frequency bands. Although SAR is
determined at the highest certified power level, the
actual SAR level of the phone while operating can be
well below the maximum value. Because the phone
is designed to operate at multiple power levels to
use only the power required to reach the network, in
general, the closer you are to a wireless base station
antenna, the lower the power output.
Before a phone model is available for sale to the
public, it must be tested and certified to the FCC
that it does not exceed the limit established by the
government-adopted requirement for safe exposure.
The tests are performed in positions and locations
(e.g., at the ear and worn on the body) as required by
the FCC for each model. The highest SAR value for
this model phone when tested for use at the ear is
1.29 W/kg and when worn on the body, as described
in this user’s manual, is 1.25 W/kg. (Body-worn
measurements differ among phone models, depending
upon available accessories and FCC requirements.)
While there may be differences between SAR levels of
various phones and at various positions, they all meet
the government requirement for safe exposure.
The FCC has granted an Equipment Authorization
for this model phone with all reported SAR levels
evaluated as in compliance with the FCC RF emission
guidelines. SAR information on this model phone is on
file with the FCC and can be found under the Display
Grant section of http://www.fcc.gov/oet/fccid after
searching on FCC ID BEJL1400.
Additional information on Specific Absorption
Rates (SAR) can be found on the Cellular
Telecommunications Industry Association (CTIA)
website at http://www.wow-com.com
* In the United States and Canada, the SAR limit for
mobile phones used by the public is 1.6 watts/kg (W/
kg) averaged over one gram of tissue. The standard
incorporates a substantial margin of safety to give
additional protection for the public and to account for
any variations in measurements.
85
Page 86
Glossary
To help you understand the main technical terms
and abbreviations used in this booklet and take full
advantage of the feature on your mobile phone, here
are a few definitions.
Call Barring
Ability to restrict outgoing and incoming calls.
Call Forwarding
Ability to reroute calls to another number.
Call Waiting
Ability to inform users that they have an incoming call
when engaged on another call.
GPRS (General Packet Radio Service)
GPRS guarantees continuous connection to the
Internet for mobile phone and computer users. It is
based on the Global System for Mobile Communication
(GSM) circuit-switched cellular phone connections
and the Short Message Service (SMS).
86
GSM (Global System for Mobile
Communication)
International standard for cellular communication,
guaranteeing compatibility between the various
network operators. GSM covers most European
countries and many other parts of the world.
Java
Programming language generating applications that
can run on all hardware platforms, whether small,
medium or large, without modification. It has been
promoted for and geared heavily to the Web, both for
public Web sites and Intranets. When a Java program
runs from a Web page, it is called a Java applet. When
it is run on a mobile phone or pager, it is called a
MIDlet.
Line Identification Services (Caller ID)
Service allowing subscribers to view or block the
telephone numbers of callers.
Multiparty Calls
Ability to establish a conference call involving up to
five additional parties.
Page 87
Phone Password
Security code used to unlock the phone when you have
selected the option to lock it automatically each time it
switches on.
Roaming
Use of your phone when you are outside your home
area (when traveling for example).
SIM (Subscriber Identification Module)
Card containing a chip with all the information
required to operate the phone (network and memory
information, as well as the subscriber’s personal data).
The SIM card fits into a small slot on the back of the
phone and is protected by the battery.
SMS (Short Message Service)
Network service sending and receiving messages to
and from another subscriber without having to speak to
the correspondent. The message created or received
(up to 160 characters long) can be displayed, received,
edited or sent.
Glossary
Patent Information
This product was manufactured under one or more of the
following U.S.
patents: 5276765 5749067 6061647
DATE: 2005.01.03 (FC)
87
Page 88
Memo
Page 89
Memo
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.