LG LFX25973ST/04 Owner’s Manual
ENGLISH
FRANÇAIS
ESPAÑOL
OWNER’S MANUAL
FRENCH DOOR
REFRIGERATOR
Please read this owner's manual thoroughly before
operating and keep it handy for reference at all times.
LFX25974**
P.No.:MFL63264279
www.lg.com
2
TABLE OF CONTENTS
TABLE OF CONTENTS
ENGLISH
3 PRODUCT FEATURES
4
IMPORTANT SAFETY
INSTRUCTIONS
7 COMPONENTS
7 Refrigerator Exterior
8 Refrigerator Interior
9 INSTALLATION
9 Installation Overview
10 Specifications
11 Unpacking Your Refrigerator
11 Choosing the Proper Location
11 - Flooring
12 - Ambient Temperature
12 - Measuring the Clearances
12 Removing/Assembling the Refrigerator
Door Handles
13 Removing/Assembling the Freezer
Drawer Handle
13 Removing/Assembling the Doors and
Drawers
13 - Removing the Left Refrigerator Door
14 - Removing the Right Refrigerator Door
15 - Assembling the Right Refrigerator Door
15 - Assembling the Left Refrigerator Door
16 - Removing the Freezer Drawers
17 - Assembling the Freezer Drawers
19 Connecting the Water Line
19 - Before You Begin
19 - Water Pressure
19 - What You Will Need
20 - Water Line Installation Instructions
22 Turning On the Power
23 Leveling and Door Alignment
23 - Leveling
23 - Door Alignment
24 HOW TO USE
24 Before Use
25 Control Panel
25 - Control Panel Features
27 In-Door Ice Bin
27 - Detaching the In-Door Ice Bin
27 - Assembling the In-Door Ice Bin
28 Automatic Icemaker
28 - Turning the Automatic Icemaker On or
Off
29 - When You Should Turn the Icemaker Off
29 - Normal Sounds You May Hear
29 - Preparing for Vacation
30 Ice and Water Dispenser
30 - Dispenser
30 - Using the Dispenser
30 - Locking the Dispenser
30 - Cleaning the Dispenser Stand
31 Storing Food
31 - Food Preservation Location
32 - Food Storage Tips
32 - Storing Frozen Food
33 Humidity Controlled Crisper
34 Detaching and Assembling the Storage
Bins
35 Adjusting the Refrigerator Shelves
36 MAINTENANCE
36 Cleaning
37 Replacing the Water Filter
39 SMART DIAGNOSIS
39 Using Smart Diagnosis
40 TROUBLESHOOTING
50 WARRANTY
PRODUCT FEATURES
3
PRODUCT FEATURES
* Depending on the model, some of the following functions may not be available.
FILTERED WATER AND ICE DISPENSER
The water dispenser dispenses fresh, chilled water.
The ice dispenser dispenses cubed and crushed ice.
DOOR ALARM
The Door Alarm function is designed to prevent refrigerator malfunctioning
that could occur if a refrigerator door or freezer drawer remains open. If a
refrigerator door or freezer drawer is left open for more than 60 seconds, a
warning alarm sounds in 30 second intervals.
HUMIDITY CONTROLLED CRISPER
The Humidity Controlled Crisper is designed to help keep your fruits and
vegetables fresh and crisp. You can control the amount of humidity in the
crisper by adjusting the setting between Low and High.
GLIDE‘N’SERVE
Glide`N’Serve provides storage space that keeps the compartment colder
than the refrigerator.
It is a convenient place to store sandwiches or meat to be cooked.
ENGLISH
ICE PLUS
Ice production can be increased by approximately 20 percent when the
freezer section is maintained at the coldest temperature for a 24-hour
period.
:This product contains chemicals known to the State of California
to cause cancer and birth defects or other reproductive harm.Wash hands after handling.
IMPORTANT SAFETY INSTRUCTIONS
5
READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE.
To reduce the risk of fire, electric shock, or personal injury when using your product, basic safety
precautions should be followed, including the following.
Do not use this product for special purposes (storage of medicine or test materials or for ships,
y
etc).
Unplug the power plug before cleaning or repairing the refrigerator.
y
When you replace the light bulb in the refrigerator, unplug the refrigerator or turn off the power.
y
Do not modify or extend the power cord.
y
Do not use a dryer to dry the interior. Do not light a candle to remove the interior odor.
y
For your safety, this appliance must be properly grounded. Have the wall outlet and the circuit
y
checked by a qualified electrician to make sure the outlet is properly grounded.
Do not use an outlet that can be turned off with a switch. Do not use an extension cord. It is the
y
user’s responsibility to replace a standard 2-prong wall outlet with a standard 3-prong wall outlet.
Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.
y
Do not use an adapter plug and plug the power plug into a multi-outlet extension cord.
y
Disconnect the power cord immediately if you hear a noise, smell a strange odor or detect
y
smoke.
Turn the power off if water or dust penetrates into the refrigerator. Call a service agent.
y
Do not disassemble or modify the refrigerator.
y
Do not put hands, feet, or metal objects below or behind the refrigerator.
y
Do not operate the refrigerator or touch the power cord with wet hands.
y
In refrigerators with automatic icemakers, avoid contact with the moving parts of the ejector
y
mechanism or with the heating element that releases the cubes. Do not place fingers or hands
on the automatic ice-making mechanism while the refrigerator is plugged in.
When dispensing ice from the dispenser, do not use crystal ceramics.
y
Do not touch the cold surfaces in the freezer compartment with wet or damp hands, when your
y
refrigerator is in operation.
Do not put glass containers, glass bottles or soda in the freezer.
y
This appliance is not intended for use by persons (including children) with reduced physical,
y
sensory or mental capabilities, or lack of experience and knowledge, unless they have been given
supervision or instruction concerning the use of the appliance by a person responsible for their
safety.
Do not refreeze frozen food that have thawed completely. It may result in a serious health issue.
y
If you are throwing away your old refrigerator, make sure the CFC coolant is removed for proper
y
disposal by a qualified servicer. If you release CFC coolant, you may be fined or imprisoned in
accordance with the relevant environmental law.
Junked or abandoned refrigerators are dangerous, even if they are sitting for only a few days.
y
When disposing the refrigerator, remove the packing materials from the door or take off the
doors but leave the shelves in place so that children may not easily climb inside.
ENGLISH
6
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE.
ENGLISH
To reduce the risk of fire, electric shock, or personal injury when using your product, basic safety
precautions should be followed, including the following.
CAUTION
Installation
The refrigerator must be properly installed in accordance with the Installer Instructions that
y
were taped to the front of the refrigerator.
Be careful when you unpack and install the refrigerator. Immediately dispose of packing
y
materials (plastic) out of reach of children.
Use
Close the door carefully when children are around.
y
Keep fingers out of pinch point areas; clearances between the doors and cabinets are
y
necessarily small. Be careful closing doors when children are in the area.
If you store food properly, beware that it may fall and cause injury.
y
Maintenance
Do not use strong detergents like wax or thinners for cleaning. Clean with a soft fabric.
y
Wipe foreign objects (dust, water, etc) off the prongs of the power plug and contact areas
y
regularly.
Supply Cord
Replacement
If the supply cord is damaged, it must be replaced by the manufacturer or its service agent
or a similarly qualied person in order to avoid a hazard.
SAVE THESE INSTUCTIONS
COMPONENTS
7
COMPONENTS
Use this page to become more familiar with the parts and features of your refrigerator.
Page references are included for your convenience.
*The appearance and specifications of the actual product may differ depending on the model.
Refrigerator Exterior
LED Display
Displays the refrigerator and
freezer temperature, the water
filter condition and the dispenser
status.
Ice Plus
When this feature is activated,
the freezer section will run at the
coldest temperature for a 24-hour
period to increase ice production.
Door Alarm
A warning alarm sounds at 30second intervals when the
refrigerator or freezer door is left
open for more than 60 seconds.
Filtered Water and
Ice Dispenser
Dispenses fresh, chilled,
filtered water through
the door. The ice
dispenser offers cubed
or crushed ice.
ENGLISH
8
COMPONENTS
Refrigerator Interior
ENGLISH
LED Interior Lamps
The interior lamps light up the
inside of the refrigerator.
Water Filter
SpacePlus Ice System
Automatically produces
80-130 ice cubes in a
24-hour period.
Fixed Door Bins
Smart Diagnosis Speaker
Hold your phone to this speaker when
activating Smart Diagnosis. Refer to the
Smart Diagnosis section for more details.
Dairy Product Bin
Refrigerator Shelves
The shelves in your
refrigerator are adjustable
to meet your individual
storage needs.
Mullion
Folds in when the
left door is opened.
Can Storage Bin
Used to preserve chilled
food or drinks.
Glide’N’Serve
Allows you to store food items
at a different temperature than
the regular refrigerator area.
Auto Closing Hinge
The refrigerator doors
and freezer drawers close
automatically when you push
them slightly.
(The door only closes
automatically when it is open
at an angle of less than 30°.)
Modular Door Bins
Crispers
Controls humidity and
helps vegetables and
fruit to stay crisp.
Pullout Drawer
Durabase
Durabase Divider
INSTALLATION
9
INSTALLATION
Installation Overview
Please read the following installation instructions first after purchasing this product or transporting
it to another location.
1 Unpacking your
refrigerator
4 Connecting the water
supply and water line
2 Choosing the proper
location
5 Leveling and Door
Alignment
3 Disassembling/Assembling
ENGLISH
10
INSTALLATION
Specifications
ENGLISH
The appearance and specifications listed in this manual may vary due to constant product
improvements.
Bottom-freezer refrigerator model LFX25974
Description French door refrigerator
Electrical requirements 115 VAC @ 60 Hz
Min. / Max. Water pressure 20 and 120 psi (140 and 830 kPa)
Dimensions 35 3/4” (W) X 34 1/4” (D) X 69 3/4” (H), 46 1/2” (D w/ door open)
908 mm (W) X 869.95 mm (D) X 1 771.65 (H), 1 181.1 mm (D w/ door
open)
Net weight
309 lb. (140kg)
INSTALLATION
11
Unpacking Your Refrigerator
WARNING
Use two or more people to move and
y
install the refrigerator. Failure to do so
can result in back or other injury.
Your refrigerator is heavy. When moving
y
the refrigerator for cleaning or service,
be sure to protect the floor. Always pull
the refrigerator straight out when moving
it. Do not wiggle or walk the refrigerator
when trying to move it, as floor damage
could occur.
Keep flammable materials and vapors,
y
such as gasoline, away from the
refrigerator. Failure to do so can result in
fire, explosion, or death.
Remove tape and any temporary labels from your
refrigerator before using. Do not remove any
warning-type labels, the model and serial number
label, or the Tech Sheet that is located under the
front of the refrigerator.
To remove any remaining tape or glue, rub the
area briskly with your thumb. Tape or glue residue
can also be easily removed by rubbing a small
amount of liquid dish soap over the adhesive with
your fingers. Wipe with warm water and dry.
Do not use sharp instruments, rubbing alcohol,
flammable fluids, or abrasive cleaners to remove
tape or glue. These products can damage the
surface of your refrigerator.
Refrigerator shelves are installed in the shipping
position. Please reinstall shelves according to
your individual storage needs.
Choosing the Proper Location
Select a place where a water supply can
y
be easily connected for the automatic
icemaker.
NOTE
The water pressure must be between 20
and 120 psi (140 and 830 kPa)on models
without a water filter and between 40 and
120 psi (280 and 830kPa) on models with
a water filter.
The refrigerator should always be plugged
y
into its own individual properly grounded
electrical outlet rated for 115 Volts, 60 Hz,
AC only, and fused at 15 or 20 amperes.
This provides the best performance
and also prevents overloading house
wiring circuits which could cause a fire
hazard from overheated wires. It is
recommended that a separate circuit
serving only this appliance be provided.
WARNING
To reduce the risk of electric shock, do not
install the refrigerator in a wet or damp
area.
Flooring
To avoid noise and vibration, the unit must be
leveled and installed on a solidly constructed
floor. If required, adjust the leveling legs to
compensate for unevenness of the floor. The
front should be slightly higher than the rear to
aid in door closing. Leveling legs can be turned
easily by tipping the cabinet slightly. Turn the
leveling legs to the left to raise the unit or to
the right to lower it. (See Leveling and door
AlIgnment.)
ENGLISH
NOTE
Installing on carpeting, soft tile surfaces,
a platform or weakly supported structure
is not recommended.
12
INSTALLATION
Ambient Temperature
ENGLISH
Install this appliance in an area where the
temperature is between 55°F (13°C) and 110°F
(43°C). If the temperature around the appliance
is too low or high, cooling ability may be
adversely affected.
Measuring the Clearances
Too small of a distance from adjacent items
may result in lowered freezing capability and
increased electricity consumption charges.
Allow at least 24 inches (61 cm) in front of the
refrigerator to open the doors, and at least
2 inches (5.08 cm) between the back of the
refrigerator and the wall.
24” (61 cm)
Removing/Assembling the
Refrigerator Door Handles
NOTE
Removing the doors is always
recommended when it is necessary to
move the refrigerator through a narrow
opening. If it is necessary to remove the
handles, follow the directions below.
Removing the Handles
Loosen the set screws with a 3/32 in.
1
Allen wrench and remove the handle.
Loosen the mounting fasteners that
2
connect to the refrigerator door and handle
using a 1/4 in. Allen wrench, remove the
mounting fasteners.
2” (5.08 cm)
Assembling the Handles
Assemble the mounting fasteners at
1
both ends of the handle using a 1/4 in.
Allen wrench.
Place the handle on the door by fitting
2
the handle footprints over the mounting
fasteners and tightening the set screws
with a 3/32 in. Allen wrench.
INSTALLATION
13
Removing/Assembling the
Freezer Drawer Handle
Removing the Handles
Loosen the set screws located on the
1
lower side of the handle with a 1/8 in. Allen
wrench and remove the handle.
Loosen the mounting fasteners that
2
connect to the
freezer drawer
and handle
using a 1/4 in.
Allen wrench,
and remove
the mounting
fasteners.
Assembling the Handles
Assemble the mounting fasteners at
1
both ends of the handle using a 1/4 in. Allen
wrench.
Place the handle on the door by fitting
2
the handle
footprints over
the mounting
fasteners and
tightening the
set screws
with a 1/8 in.
Allen wrench.
WARNING
When the customer takes apart the handle
or assemble it from a refrigerator, please be
cautious of following things.
Hold the handle with your own hand to
y
make sure not to drop the handle to the
floor or instep while taking apart the handle
from a refrigerator.
Do not swing the handle towards people or
y
animals after taking apart the handle.
Insert the bracket hole of the handle into
y
the stopper bolt of the door exactly, and
then assemble the set screws to fix the
handle.
Check if there’s any gap between the door
y
and handle after fixing the handle.
Removing/Assembling the
Doors and Drawers
Removing the doors is always recommended
when it is necessary to move the refrigerator
through a narrow opening.
WARNING
If your entrance door is too narrow for the
y
refrigerator to pass through, remove the
refrigerator doors and move the refrigerator
sideways through the doorway.
Use two or more people to remove and
y
install the refrigerator doors. Failure to do
so can result in back or other injury.
Disconnect the electrical supply to the
y
refrigerator before installing. Failure to do
so could result in serious injury or death.
Do not put hands, feet or other objects into
y
the air vents or bottom of the refrigerator.
You may be injured or receive an electrical
shock.
Be careful when handling the hinge and
y
stopper. It may result in injury.
Remove food and bins from the doors and
y
drawers before detaching.
Removing the Left Refrigerator Door
The water supply is connected to the
1
upper right part of the rear surface of the
refrigerator. Remove the ring in the joint
area. Hold the water supply connection
and gently push the Collet to detach the
water supply line as shown in and .
Collet
NOTE
Detachment of the water supply line is
applicable only when detaching the left
refrigerator door.
ENGLISH
14
(2)
(3)
(4)
(5)
(1)
INSTALLATION
ENGLISH
2
3
4
5
6
7
8
9
(2)
(3)
(5)
(6)
(7)
(8)
Open the left door. Remove the top hinge
cover screw (1). Lift up the cover (2).
Remove the cover.
Pull out the tube (3).
Disconnect all wire harnesses (4).
Remove the grounding screw (5).
Rotate the hinge lever (6)
counterclockwise. Lift the top hinge (7)
free of the hinge lever latch (8).
Lift the door from the middle hinge pin and
remove the door.
Place the door, inside facing up, on a non-
scratching surface.
(1)
(4)
Removing the Right Refrigerator Door
Open the door. Remove the top hinge
1
cover screw (1). Lift up the cover (2).
Remove the cover.
2
Rotate the hinge lever (3) clockwise. Lift
3
the top hinge (4) free of the hinge lever
latch (5).
Lift the door from the middle hinge pin and
4
remove the door.
Place the door, inside facing up, on a non-
5
scratching surface.
CAUTION
When lifting the hinge free of the latch, be
careful that the door does not fall forward.
CAUTION
When lifting the hinge free of the latch, be
careful that the door does not fall forward.
INSTALLATION
(2)
(3)
(4)
(5)
(1)
15
Assembling the Right Refrigerator
Door
Install the right-side door first.
Lower the door onto the middle hinge
1
pin. Make sure that the plastic sleeve is
inserted into the bottom of the door.
Fit the top hinge (4) over the hinge lever
2
latch (5) and into place.
Rotate the lever (3) counterclockwise to
3
secure the hinge.
Hook the tabs on the right side of the
4
hinge cover (2) under the edge of the top
hinge (4) and position the cover in place.
Insert and tighten the cover screw (1).
5
Assembling the Left Refrigerator
Door
Install the left refrigerator door after the right
door is installed.
Lower the door onto the middle hinge pin.
1
(2)
(3)
(5)
(6)
(7)
(8)
Fit the top hinge (7) over the hinge lever
2
latch (8) and into place.
Rotate the lever (6) clockwise to secure
3
the hinge.
Install the grounding screws (5) and
4
connect the two wire harnesses (4).
Push the water tube (3) located at the top
5
of the left door into the hole beside the left
hinge on the top of the cabinet until it exits
through the back.
Insert the water supply tube (3) into the
6
connector until you see only one scale
mark. Fully insert the tub cover (15 mm).
Hook the tabs on the left side of the hinge
7
cover (1) under the edge of the top hinge (7)
and position the cover in place.
Insert and tighten the cover screw (1).
8
(1)
(4)
ENGLISH
16
INSTALLATION
ENGLISH
9
10
11
Insert the water supply tube at least 5/8 in.
(15 mm) into the connector.
Hook the tab on the door switch side
of the cover under the edge of the wire
opening in the cabinet top.
Position the cover into place. Insert and
tighten the cover screw.
NOTE
Collet
Tube
Insert Line
Clip
Removing the Freezer Drawers
The top, middle and bottom drawers are all
removed in the same way. In the following
figures, the Pullout Drawer located above the
freezer drawer is not shown for clarity.
CAUTION
Use two or more people to remove and
y
install the freezer drawer. Failure to do so
can result in back or other injury.
Do not hold the handle when removing
y
or replacing the drawer. The handle may
come off and it could cause personal
injury.
Be careful of sharp hinges on both sides
y
of the drawer.
When you lay the drawer down, be
y
careful not to damage the floor.
Do not sit or stand on the freezer drawer.
y
To prevent accidents, keep children and
y
pets away from the drawer. Do not leave
the drawer open.
Pull the drawer open to full extension.
1
Remove the lower basket by lifting basket
from rail system.
1) Gently press the Collet and insert the
tube until only one line shows on the
tube.
(Correct)
(Incorrect)
2) Pull the tube to make sure that the
tube is tightly fastened and then insert
the clip.
1
Press in the tabs on the rail covers and
2
lift them up to separate from the rail
assembly.
Remove the rail screw 2 on both the left
3
and right rails.
2
With both hands, grasp the sides of the door
4
and pull it up to separate it from the rails.
CAUTION
When you remove the drawer, do not
hold the handle. The handle may come
off and it could cause personal injury.
INSTALLATION
Assembling the Freezer Drawer
With both hands, pull out each rail
1
simultaneously until both rails are fully
extended.
Hook the door support 1 into the rail tabs
2
2
on both sides.
Lower door into final position and tighten the
3
screws 3.
1
2
17
ENGLISH
With both hands, hold each rail and push it in
5
to allow both rails to slide in simultaneously.
3
18
INSTALLATION
Assembling the Freezer Drawer
ENGLISH
(continued)
Make sure you have the correct rail cover
4
for each side.
Left Rail
Cover
Align the tabs on the covers with the
5
assembly holes on each rail, and snap the
rail covers in place to secure.
Right Rail
Cover
WARNING
If the Durabase divider is removed, there is
y
enough open space for children or pets to
crawl inside. To prevent accidental child and
pet entrapment or suffocation risk, DO NOT
allow them to touch or go near the freezer
drawer.
DO NOT step or sit down on freezer
y
drawer.
With the drawer pulled out to full
6
extension, insert the lower basket
the rail assembly.
4
Assembly
Hole
4
in
INSTALLATION
19
Connecting the Water Line
Before You Begin
This water line installation is not covered by the
refrigerator warranty. Follow these instructions
carefully to minimize the risk of expensive water
damage.
Water hammer (water banging in the pipes) in
house plumbing can cause damage to refrigerator
parts and can lead to water leakage or flooding.
Call a qualified plumber to correct water hammer
before installing the water supply line to the
refrigerator.
CAUTION
To prevent burns and product damange,
only connect the refrigerator water line to
a cold water supply.
If you use your refrigerator before connecting
the water line, make sure the icemaker power
switch is in the OFF (O) position.
CAUTION
Do not install the icemaker tubing in
areas where temperatures fall below
freezing.
Water Pressure
A cold water supply. The water pressure must
be between 20 and 120 psi (140 and 830 kPa)
on models without a water filter and between 40
and 120 psi (280 and 830kPa) on models with
a water filter.
If a reverse osmosis water filtration system is
connected to your cold water supply, this water
line installation is not covered by the refrigerator
warranty. Follow the following instructions
carefully to minimize the risk of expensive water
damage.
If a reverse osmosis water filtration system is
connected to your cold water supply, the water
pressure to the reverse osmosis system needs to
be a minimum of 40 and 60 psi ( 280 and 420
kPa), less than 2.0~3.0 sec. to fill a cup of 7 oz
(200 cc) capacity.
CAUTION
Wear eye protection during installation
to prevent injury.
If the water pressure from the reverse osmosis
system is less than 21 psi (145 kPa) (takes more
than 4.0 sec to fill a cup of 7 oz (200 cc) capacity):
Check to see if the sediment filter in
the reverse osmosis system is blocked.
Replace the filter if necessary.
Allow the storage tank on the reverse
usage.
If the issue concerning water pressure
from reverse osmosis remains, call a
licensed, qualified plumber.
All installations must be in accordance
with local plumbing code requirements.
What You Will Need
Copper Tubing,
connect the refrigerator to the water
supply. Be sure both ends of the tubing
are cut square.
To determine how
much tubing you need:
measure the distance
from the water valve on the back of the
refrigerator to the water supply pipe.
Then, add 8 feet
(2.4 m). Be sure there is sufficient extra
tubing (about 8 feet [2.4 m] coiled into 3
turns of about 10 in. [25 cm] diameter)
to allow the refrigerator to move out
from the wall after installation.
Power drill.
½ in. or adjustable
wrench.
Flat blade and Phillips
head screwdrivers.
Two ¼ in. outer
diameter compression
nuts and 2 ferrules (sleeves)
copper tubing to the shutoff valve and
the refrigerator water valve.
¼ in. outer diameter, to
to connect the
ENGLISH
20
INSTALLATION
ENGLISH
If your existing copper water line has a
y
flared fitting at the end, you will need
adapter
an
stores) to connect the water line to the
refrigerator OR you can cut off the flared
fitting with a tube
cutter and then use a
compression fitting.
Shutoff valve to
y
connect to the cold water line.
valve should have a water inlet with a
minimum inside diameter of 5/32 in. at
the point of connection to the COLD
WATER LINE. Saddle-type shutoff valves
are included in many water supply kits.
Before purchasing,
make sure a saddletype valve complies
with your local
plumbing codes.
A self piercing saddle type water valve
should not be used.
(available at plumbing supply
The shutoff
NOTE
Water Line Installation Instructions
WARNING
When using any electrical device
(such as a power drill) during
installation, be sure the device is
battery powered, double insulated
or grounded in a manner that will
prevent the hazard of electric shock.
Install the shutoff valve on the nearest
frequently used drinking water line.
SHUT OFF THE MAIN WATER SUPPLY
1
Turn on the nearest faucet to relieve the
pressure on the line.
CHOOSE THE VALVE LOCATION
2
Choose a location for
the valve that is easily
accessible. It is best to
connect into the side of a
vertical water pipe. When
it is necessary to connect
into a horizontal water
pipe, make the connection to the top or
side, rather than at the bottom, to avoid
drawing off any sediment from the water
pipe.
DRILL THE HOLE FOR THE VALVE
3
Drill a ¼ in. hole in
the water pipe using
a sharp bit. Remove
any burrs resulting
from drilling the hole
in the pipe. Be careful
not to allow water
to drain into the drill. Failure to drill a ¼ in.
hole may result in reduced ice production
or smaller cubes.
NOTE
The hookup line cannot be white, plastic
tubing. Licensed plumbers must use
only copper tubing NDA tubing #49595
or 49599 or Cross Link Polyethylene
(PEX) tubing.
INSTALLATION
21
FASTEN THE SHUTOFF VALVE
4
Fasten the shutoff valve to the cold water
pipe with the pipe clamp.
Pipe Clamp
Saddle-Type
Shutoff Valve
Vertical Cold
Water Pipe
NOTE
Commonwealth of Massachusetts
Plumbing Codes 248CMR shall be
adhered to. Saddle valves are illegal and
use is not permitted in Massachusetts.
Consult with your licensed plumber.
TIGHTEN THE PIPE CLAMP
5
Tighten the clamp screws until the sealing
washer begins to swell.
NOTE: Do not overtighten clamp or
you may crush the tubing.
Washer
Pipe Clamp
Clamp Screw
ROUTE THE TUBING
6
Route the tubing between the cold water
line and the refrigerator.
Route the tubing through a hole drilled in
the wall or floor (behind the refrigerator or
adjacent base cabinet) as close to the wall
as possible.
NOTE
Be sure there is sufficient extra tubing
(about 8 feet coiled into 3 turns of
about 10 in. diameter) to allow the
refrigerator to move out from the wall
after installation.
Inlet End
CONNECT THE TUBING TO THE VALVE
7
Place the compression nut and ferrule
(sleeve) for copper tubing onto the end of
the tubing and connect it to the shutoff
valve. Make sure the tubing is fully inserted
into the valve. Tighten the compression
nut securely.
Saddle-Type
Shutoff Valve
Packing Nut
Outlet Valve
FLUSH OUT THE TUBING
8
Compression
Nut
Ferrule (sleeve)
Turn the main water
supply on and flush out
the tubing until the water
is clear.
Shut the water off at the
water valve after about
one quart of water has
been flushed through the tubing.
CONNECT THE TUBING TO THE
9
REFRIGERATOR
Before making the connection
NOTE:
to the refrigerator, be sure that the
refrigerator power cord is not plugged into
the wall outlet.
a. Remove the plastic flexible cap from
the water valve.
b. Place the compression nut and ferrule
(sleeve) onto the end of the tubing as
shown.
c. Insert the end of the copper tubing into
the connection as far as possible. While
holding the tubing, tighten the fitting.
Tubing Clamp
¼ in.
Compression
Nut
Ferrule
(sleeve)
¼ in. Tubing
Refrigerator
Connection
ENGLISH
22
INSTALLATION
ENGLISH
VALVE
Tighten any connections that leak.
CAUTION
Check to see if leaks occur at the water
line connections.
PLUG IN THE REFRIGERATOR
11
Arrange the coil of tubing so that it
does not vibrate against the back of the
refrigerator or against the wall. Push the
refrigerator back to the wall.
START THE ICEMAKER
12
Set the icemaker power switch to the ON
position.
The icemaker will not begin to operate
until it reaches its operating temperature
of 16°F (-9°C) or below. It will then begin
operation automatically if the icemaker
power switch is in the ON (I) position.
TURN THE WATER ON AT THE SHUTOFF
10
Turning On The Power
Plug in the refrigerator.
1
CAUTION
Connect to a rated power outlet.
y
Have a certified electrician check
y
the wall outlet and wiring for proper
grounding.
Do not damage or cut off the ground
y
terminal of the power plug.
INSTALLATION
23
Leveling and Door Alignment
Leveling
After installing, plug the refrigerator’s power
cord into a 3-prong grounded outlet and push
the refrigerator into the final position.
Your refrigerator has two front leveling legs—
one on the right and one on the left. Adjust the
legs to alter the tilt from front-to-back or sideto-side. If your refrigerator seems unsteady, or
you want the doors to close more easily, adjust
the refrigerator’s tilt using the instructions
below:
Remove the base grille. Refer to the Base
1
Grille Installation section.
Turn the leveling leg to the left to raise
2
that side of the refrigerator or to the right
to lower it. It may take several turns of
the leveling leg to adjust the tilt of the
refrigerator.
ENGLISH
Door Alignment
Both the left and right refrigerator doors have
an adjustable nut, located on the bottom hinge,
to raise and lower them to align properly.
If the space between your doors is uneven,
follow the instructions below to align the doors
evenly:
Use the wrench (included with the Owner’s
Manual) to turn the nut in the door hinge to
adjust the height. To the right to raise or to the
left to lower the height.
NOTE
A flare nut wrench works best, but an
open-end wrench will suffice.
Do not over-tighten.
Open both doors again and check to make
3
sure that they close easily. If the doors do
not close easily, tilt the refrigerator slightly
more to the rear by turning both leveling
legs to the left. It may take several more
turns, and you should turn both leveling
legs the same mount.
Replace the base grille.
4
24
HOW TO USE
HOW TO USE
ENGLISH
Before use
Clean the refrigerator.
Clean your refrigerator thoroughly and wipe off all dust that accumulated during
shipping.
CAUTION
Do not scratch the refrigerator with a sharp object or use a detergent that
y
contains alcohol, a flammable liquid or an abrasive when removing any tape
or adhesive from the refrigerator,.
Do not peel off the model or serial number label or the technical information
y
on the rear surface of the refrigerator.
NOTE
Remove adhesive residue by wiping it off with your thumb or dish detergent.
Connect the power supply.
Check if the power supply is connected before use.
Read the “Turning On The Power” section.
Turn off the icemaker if the refrigerator is not yet connected to the
water supply.
Turn off the automatic icemaker and then plug the power plug of the refrigerator
into the grounded electric outlet.
* This is applicable only to certain models.
CAUTION
Running the automatic icemaker before connecting it to the water
supply may cause the refrigerator to malfunction.
Wait for the refrigerator to cool.
Allow your refrigerator to run for at least two to three hours before putting food in
it. Check the flow of cold air in the freezer compartment to ensure proper cooling.
CAUTION
Putting food in the refrigerator before it has cooled could cause the
food to spoil, or a bad odor could remain inside the refrigerator.
The refrigerator makes a loud noise after initial operation.
This is normal. The loudness will decrease as the temperature lowers.
Open refrigerator doors and freezer drawers to ventilate the interior.
The inside of the refrigerator may smell like plastic at first. Remove any adhesive
tape from inside the refrigerator and open the refrigerator doors and the freezer
drawers for ventilation.
HOW TO USE
25
Control Panel
* Depending on the model, some of the following functions may not be available.
Control Panel Features
The LED Display shows the temperature settings, dispenser options, water filter, door alarm, and
locking status messages.
epyT ecI epyT ecI
Press the ICE TYPE button to select either
Crushed or Cubed Ice. The selected option will
illuminate on the LED display.
rezeerF rezeerF
LED Display
Press the FREEZER button to adjust the
temperature in the freezer compartment.
NOTE
To change the display from Fahrenheit to
Celsius, press and hold the FREEZER and
REFRIGERATOR button for five seconds.
ENGLISH
Control
Buttons
Refrigerator Refrigerator
Press the REFRIGERATOR button to adjust the
temperature in the freezer compartment.
sulP ecI sulP ecI
This function increases both ice making and
freezing capabilities.
When you touch the Ice Plus button, the
graphic will illuminate in the display and
will continue for 24 hours. The function will
automatically shut off after 24 hours.
You can stop this function manually by
touching the button one more time.
26
HOW TO USE
Control Panel Features (continued)
ENGLISH
Energy Saving
The Energy Saving function disables the mullion
heater located on the refrigerator door in order to
conserve electricity. Press and hold the Energy
Saving button for three seconds to activate or
deactivate this function.
NOTE
Discontinue using the Energy Saving function
if excessive moisture begins to collect on the
door mullion.
Light
Press the LIGHT button, to turn on the
dispenser light. The indicator will appear on the
LED display.
Change Filter
When the water filter indicator turns on, you
have to change the water filter. After changing
the water filter, press and hold the FILTER
button for three seconds to turn the indicator
light off. You need to change the water filter
approximately every six months.
Alarm
When power is connected to the
refrigerator, the door alarm is initially set to
ON. When you press the ALARM button,
the display will change to OFF and the
Alarm function will deactivate.
When either the refrigerator or the freezer
door is left open for more than 60 seconds,
the alarm tone will sound to let you know
that the door is open.
When you close the door, the door alarm
will stop.
Control Lock
The Control Lock function disables every other
button on the display.
When power is initially connected to the
refrigerator, the Lock function is off.
If you want to activate the Lock function to
lock other buttons, press and hold the Lock
button for three seconds or more. The Lock
icon will display and the Lock function is
now enabled.
To disable the Lock function, press and hold
the Lock button for approximately three
seconds.
CAUTION
Display Mode (For Store Use Only)
The Display Mode disables all cooling
in the refrigerator and freezer sections
to conserve energy while on display in
a retail store. When activated, OFF will
display on the control panel.
To deactivate:
With either refrigerator door opened,
press and hold the Refrigerator and Ice
Plus buttons at the same time for five
seconds. The control panel will beep and
the temperature settings will display to
confirm that Display Mode is deactivated.
Use the same procedure to activate the
Display Mode.
HOW TO USE
27
In-Door Ice Bin
* Depending on the model, some of the
following functions may not be available.
CAUTION
Keep hands and tools out of the ice
y
compartment door and dispenser chute.
Failure to do so may result in damage or
personal injury.
The icemaker will stop producing ice when
y
the in-door ice bin is full. If you need more
ice, empty the ice bin into the extra ice bin
in the freezer compartment. During use,
the ice can become uneven causing the
icemaker to misread the amount of ice
cubes and stop producing ice. Shaking the
ice bin to level the ice within it can reduce
this problem.
Storing cans or other items in the ice bin will
y
damage the icemaker.
Keep the ice compartment door closed
y
tightly. If the ice compartment door is not
closed tightly, the cold air in the ice bin will
freeze food in the refrigerator compartment.
This could also cause the icemaker to stop
producing ice.
If the O
y
N/OFF switch on the icemaker is
set to OFF for an extended period of time,
the ice compartment will gradually warm
up to the temperature of the refrigerator
compartment. To prevent ice cubes from
melting and leaking from the dispenser,
ALWAYS empty the ice bin when the
icemaker is set to OFF for more than a few
hours.
To remove the in-door ice bin, grip the
2
front handle, slightly lift the lower part,
and slowly pull out the bin as shown.
Assembling the In-Door Ice Bin
Carefully insert the in-door ice bin while
1
slightly slanting it to avoid contact with the
icemaker.
Avoid touching the ice-detecting sensor
2
when replacing the ice bin. See the label
on the ice compartment door for details.
ENGLISH
Detaching the In-Door Ice Bin
Gently pull the handle to open the ice
1
compartment.
Ice-detecting
sensor
CAUTION
When handling the ice bin,
keep hands away from the
icemaker tray area to avoid
personal injury.
28
HOW TO USE
Automatic Icemaker
ENGLISH
* Depending on the model, some of the
following functions may not be available.
Ice is made in the automatic icemaker and
sent to the dispenser. The icemaker will
produce 70~210 cubes in a 24-hour period,
depending on freezer compartment temperature,
room temperature, number of door openings and
other operating conditions.
It takes about 12 to 24 hours for a newly
installed refrigerator to begin making ice. Wait
72 hours for full ice production to occur.
Ice making stops when the in-door ice bin is full.
When full, the in-door ice bin holds approximately
6 to 8 (12~16 oz or 340~455 cc) glasses of ice.
The water pressure must be between 20 and 120
psi (140 and 830 kPa)on models without a water
filter and between 40 and 120 psi (280 and 830
kPa) on models with a water filter to produce the
normal amount and size of ice cubes.
Foreign substances or frost on the ice-detecting
sensor can interrupt ice production.
Make sure the sensor area is clean at all times
for proper operation.
Water fills the ice tray.
1 hour later from
supplying water
60 minutes after water has been added
to the ice tray, the ice tray will sit slightly
tilted to help the cold air reach the ice.
Power
Switch
Ice-detecting
Sensor
Icemaker
The ice-detecting sensors will sense
when the ice is ready to be dumped
into the ice bin.
Turning the Automatic Icekamer
On or Off
To turn off the automatic icemaker, set the
icemaker switch to
automatic icemaker, set the switch to
OFF (O)
. To turn on the
ON (I)
.
HOW TO USE
29
Automatic Icemaker
(continued)
CAUTION
The first ice and water dispensed may
y
include particles or odor from the water
supply line or the water tank.
Throw away the first few batches of ice
y
(about 24 cubes). This is also necessary if
the refrigerator has not been used for a long
time.
Never store beverage cans or other items in
y
the ice bin for the purpose of rapid cooling.
Doing so may damage the icemaker or the
containers may burst.
If discolored ice is dispensed, check the
y
water filter and water supply. If the problem
continues, contact a Sears or other qualified
service center. Do not use the ice or water
until the problem is corrected.
Keep children away from the dispenser.
y
Children may play with or damage the
controls.
The ice passage may become blocked with
y
frost if only crushed ice is used. Remove the
frost that accumulates by removing the ice
bin and clearing the passage with a rubber
spatula. Dispensing cubed ice can also help
prevent frost buildup.
Never use thin crystal glass or crockery to
y
collect ice. Such containers may chip or
break resulting in glass fragments in the ice.
Dispense ice into a glass before filling it
y
with water or other beverages. Splashing
may occur if ice is dispensed into a glass
that already contains liquid.
Never use a glass that is exceptionally
y
narrow or deep. Ice may jam in the ice
passage and refrigerator performance may
be affected.
Keep the glass at a proper distance from
y
the ice outlet. A glass held too close to the
outlet may prevent ice from dispensing.
To avoid personal injury, keep hands out of
y
the ice door and passage.
Never remove the dispenser cover.
y
If ice or water dispenses unexpectedly, turn
y
off the water supply and contact a qualified
service center.
When You Should Turn the
Icemaker Off
When the water supply will be shut off
y
for several hours.
When the ice bin is removed for more
y
than one or two minutes.
When the refrigerator will not be used
y
for several days.
NOTE
The ice bin should be emptied when the
icemaker on/off switch is turned to the
position.
OFF
Normal Sounds You May Hear
The icemaker water valve will buzz as
y
the icemaker fills with water. If the
power switch is in the ON (I) position,
it will buzz even if it has not yet been
hooked up to water. To stop the buzzing,
move the power switch to OFF (O).
NOTE
Keeping the power switch in the ON
(I) position before the water line is
connected can damage the icemaker.
You will hear the sound of cubes
y
dropping into the bin and water running
in the pipes as the icemaker refills.
Preparing For Vacation
Set the icemaker power switch to OFF (O) and
shut off the water supply to the refrigerator.
NOTE
The ice bin should be emptied anytime
the icemaker on/off switch is turned to
the OFF (O) position.
If the ambient temperature will drop below
freezing, have a qualified technician drain
the water supply system to prevent serious
property damage due to flooding caused by
ruptured water lines or connections.
ENGLISH
30
HOW TO USE
Ice and Water Dispenser
ENGLISH
* Depending on the model, some of the
following functions may not be available.
CAUTION
Keep children away from the dispenser.
Children may play with or damage the
controls.
Dispenser
Using the Dispenser
To dispense
y
water switch with a glass.
To dispense
y
with a glass.
cold water
, push on the ice switch
ice
Water Switch
Ice Switch
Stand
, push on the
Incorrect Way Correct Way
Water
Ice
CAUTION
Throw away the first few batches of ice
(about 24 cubes). This is also necessary
if the refrigerator has not been used for
a long time.
Locking the Dispenser
Press and hold the Alarm and Lock button
simultainously for 3 seconds to lock the
dispenser and all the control panel functions.
Follow the same instructions to unlock.
NOTE
If discolored ice is dispensed, check
y
the water filter and water supply. If the
problem continues, contact a qualified
service center. Do not use the ice or
water until the problem is corrected.
The dispenser will not operate when
y
either of the refrigerator doors are open.
If dispensing water or ice into a container
y
with a small opening, place it as close to
the dispenser as possible.
Some dripping may occur after
y
dispensing. Hold your cup beneath
the dispenser for a few seconds after
dispensing to catch all of the drops.
Cleaning the Dispenser Stand
Grip the stand with both hands and pull it
1
out.
Wipe out dirty areas with a clean cloth.
2
Loading...