Installation with L9322
Note:
This Bracket Adaptor supports only L9322 model produced later than August 2012.
Dome Bracket
Adaptor
(LFL1300)
model
Insert the Dome Bracket Adaptor to 1.5” NPT screwthread (female) pipe or to the Wall/Ceiling/Parapet
a
Mount Adaptor (LBK1000W/LBK1000P/LBK1000R)
and tighten the three pipe screws.
Warning
>
Make sure you x the three pipe screws. If not
secured tightly, the Dome Bracket Adaptor
may loosen from the Pipe or Adaptor, causing
physical damage or malfunction.
(Make sure you check the connection between
two components before proceeding with the
next step.)
Installation Guide
Dome Bracket Adaptor
Model: LFL1300
Accessories
-Installation manual
-Screw accessory
yScrew Machine(M4 x L10.0 mm) (4 ea)
Assemble the housing of the Dome Camera to the
b
Dome Bracket Adaptor and tighten four screws.
Assemble the camera and the housing and tighten
c
four screws. (Align the “FRONT” marks of the camera
mounting bracket and the camera assembly for
proper camera orientation.)
Turn the Dome Cover clockwise to secure it to the
d
camera.
Getting Started
Introduction
This product is designed for installation of LG Dome
camera into the Wall Mount assembly (LBK1000W),
Pendant Mount assembly (LBK1000P) or Parapet Mount
assembly (LBK1000R) on the ceiling or wall.
The installable LG Dome Camera
-LND3’s, LCV5’s, LCD5’s, LNV5’s, LND5’s, LND7’s, LNV7’s
and L9322 models
-Refer to the owner’s manual of LG Dome Camera for
the compatibility of this product.
-Actual set may be dier from the picture described
in this manual.
Installation Precautions
yMake sure that the installation place can endure at
least 4 times of the total weight of the Dome Bracket
Adaptor, Camera, and Wall/Ceiling/Parapet Mount
Adaptor.
yThe Dome Bracket Adaptor can be also connected
to 1.5” NPT screw-thread pipe as well as to the Wall/
Ceiling/Parapet Mount assembly.
Specifications
yDimensions (Ø x H): 141 mm x 50 mm
yNet Weight: 0.18 kg
yMaterial: Aluminum
yOperating Temperature: -50 °C to 60 °C
yOperating Humidity: 0 to 100 %
WARNING:
This product contains chemicals known to the State
of California to cause cancer and birth defects or
reproductive harm. Wash hands after handling.
Installation with LCV5's, LNV5's and LNV7's models
Installation with LCD5's, LND3's,
LND7's models
Note:
LCD5’s, LND3’s,
LND5’s
and
LND7’s models are designed for installation in an indoor surveillance system.
LND5's
and
Insert the Dome Bracket
Adaptor to 1.5” NPT screw-
thread (female) pipe
or to the Wall/Ceiling/
Parapet Mount Adaptor
(LBK1000W/LBK1000P/
LBK1000R) and tighten the
three pipe screws.
Dome Bracket Adaptor
(LFL1300)
Assemble the housing of
the Dome Camera to the
Dome Bracket Adaptor
and tighten four screws.
a
b
Warning
>
Make sure you x the three pipe
screws. If not secured tightly, the Dome
Bracket Adaptor may loosen from
the Pipe or Adaptor, causing physical
damage or malfunction.
(Make sure you check the connection
between two components before
proceeding with the next step.)
Assemble the camera
c
and the housing.
(Align the “FRONT ”
marks of the housing
and the camera
assembly for proper
camera orientation.)
Dome Bracket
Adaptor
(LFL1300)
Insert the Dome Bracket Adaptor to 1.5” NPT screw-
a
thread (female) pipe or to the Wall/Ceiling/Parapet
Mount Adaptor (LBK1000W/LBK1000P/LBK1000R)
and tighten the three pipe screws.
Warning
>
Make sure you x the three pipe screws. If not
secured tightly, the Dome Bracket Adaptor
may loosen from the Pipe or Adaptor, causing
physical damage or malfunction.
(Make sure you check the connection between
two components before proceeding with the
next step.)
Assemble the camera mounting bracket to the Dome
Bracket Adaptor and tighten four screws.
b
Turn the camera clockwise to secure it to the camera
mounting bracket. (Align the “FRONT” marks of the
c
camera mounting bracket and the camera assembly
for proper camera orientation.)
Assemble the Dome
Cover and the camera and
tighten three screws.
d
Turn the Dome Cover clockwise to secure it to the
d
camera.