LG LD300P User Manual

Before installing, operating or adjusting this product,

please read this instruction booklet carefully and completely.

Color Video Camera

Instruction Manual

Models: LD300N-B/C/D/E/F
LD300P-B/C/D/E/F

2

This lightning flash with arrow­head symbol within an equilater­al triangle is intended to alert
the user to the presence of unin­sulated dangerous voltage with­in the product’s enclosure that
may be of sufficient magnitude
to constitute a risk of electric
shock to persons.

The exclamation point within an
equilateral triangle is intended to
alert the user to the presence of
important operating and mainte­nance (servicing) instructions in
the literature accompanying the
product.

FCC WARNING: This equipment may
generate or use radio frequency energy.
Changes or modifications to this equipment
may cause harmful interference unless the
modifications are expressly approved in
the instruction manual. The user could lose
the authority to operate this equipment if
an unauthorized change or modification is
made.

REGULATORY INFORMATION: FCC
Part 15

This equipment has been tested and found
to comply with the limits for a Class A
digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed
to provide reasonable protection against
harmful interference when the equipment is
operated in a commercial environment. This
equipment generates,uses,and can radiate
radio frequency energy and,if not installed
and used in accordance with the instruction
manual,may cause harmful interference to
radio communications. Operation of this
equipment in a residential area is likely to
cause harmful interference in which case
the user will be required to correct the inter­ference at his own expense.

• A suitable conduit entries, knock-outs
or glands shall be provided in the
cable entries of this product in the end
user.

• Caution: Danger of explosion if bat

­tery is incorrectly replaced. Replaced
only with the same or equivalent type
recommended by the manufacturer.
Dispose of used batteries according to
the manufacturer’s instructions.

• Holes in metal, through which insulat­ed wires pass, shall have smooth well
rounded surfaces or shall be provided
with brushings.

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

3

WARNING: Do not install this equipment
in a confined space such as a bookcase or
similar unit.
WARNING: This is a class A product. In
a domestic environment this product may
cause radio interference in which case the
user may be required to take adequate
measures.
WARNING: Wiring methods shall be in
accordance with the National Electric Code,
ANSI/NFPA 70.
WARNING: To reduce a risk of fire or elec­tric shock, do not expose this product to rain
or moisture.
CAUTION: The apparatus should not be
exposed to water (dripping or splashing)
and no objects filled with liquids, such as
vases, should be placed on the apparatus.
CAUTION: This installation should be made
by a qualified service person and should
conform to all local codes.
CAUTION: To avoid electrical shock, do not
open the cabinet. Refer servicing to quali­fied personnel only.

This product is manufactured
to comply with EMC Directive
2004/108/EC and Low Voltage
Directive 2006/95/EC.

European representative :

LG Electronics Service Europe B.V.
Veluwezoom 15, 1327 AE Almere,
The Netherlands (Tel : [phone])

Disposal of your old appliance

1. When this crossed-out
wheeled bin symbol is
attached to a product it means
the product is covered by the
European Directive 2002/96/
EC.

2. All electrical and electronic
products should be dis­posed of separately from the
municipal waste stream via
designated collection facilities
appointed by the government
or the local authorities.

3. The correct disposal of your
old appliance will help prevent
potential negative conse­quences for the environment
and human health.

4. For more detailed informa

­tion about disposal of your
old appliance, please contact
your city office, waste disposal
service or the shop where you
purchased the product.

4

Important Safety Instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near
water.

6. Clean only with dry cloth.

7. Do not block any ventilation
openings. Install in accordance
with the manufacturer’s instruc­tions.

8. Do not install near any heat
sources such as radiators, heat
registers, stoves, or other appa­ratus (including amplifiers) that
produce heat.

9. Do not defeat the safety purpose
of the polarized or grounding-type
plug. A polarized plug has two
blades with one wider than the
other. A grounding type plug has
two blades and a third ground­ing prong. The wide blade or the
third prong are provided for your
safety. If the provided plug does
not fit into your outlet, consult an
electrician for replacement of the
obsolete outlet.

10. Protect the power cord from
being walked on or pinched par­ticularly at plugs, convenience
receptacles, and the point where

they exit from the apparatus.

11. Only use attachments/acces­sories specified by the manufac­turer.

12. Use only the cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with appa­ratus. When a cart is used, use
caution when moving the cart/
apparatus combination to avoid
injury from tip-over.

13. Unplug this apparatus during
lightning storms or when unused
for long periods of time.

14. Refer all servicing to qualified
service personnel. Servicing is
required when the apparatus has
been damaged in any way, such
as power- supply cord or plug is
damaged, liquid has been spilled
or objects have fallen into the
apparatus, the apparatus has
been exposed to rain or moisture,
does not operate normally, or has
been dropped.

5

Do not attempt to disassem­ble the camera

To prevent electric shock, do not remove
screws or covers. There are no user
serviceable parts inside. Ask a qualified
service personnel for servicing.

Do not use strong solvents or
detergents

Use a dry cloth to the camera when it is
dirty. If it is hard to remove the dirt on the
camera, use a mild detergent and wipe
it gently.

Before operating, please
check proper temperature,
humidity and power source
ratings.

Use the camera under conditions where
temperature is between -10°C ~ +50°C.

Do not expose the camera in
such conditions as shown
below.

Use in a room or area filled with cigarette
smoke, dust or gas.

Avoid the camera with direct
sunlight

Do not aim the camera at bright objects.
Never face it with direct sunlight or other
extremely bright objects. Otherwise
blooming or smear may be caused.

Handle the camera with care

Do not abuse the camera. Avoid striking,
shaking, etc. The camera could be dam­aged by improper handling or storage.

Do not expose the camera to
rain or moisture

This product is designed for indoor use
or location where it is protected from
rain and moisture. When exposed to
moisture, turn the power off immediately
and ask a qualified service personnel
for servicing. Moisture can damage the
camera and also create the danger of
electric shock.

Safety Precautions

6

What's in the box

Video Cable

Camera Body

M4 Tapping Screws

(2EA)

(Pan Lock Screw)

Adapter

(DC 12V, 300mA)

Optional

Power Cable

7

Construction

Front View

Side View

6-pin Dip Switch

Tilt Base

Focus Lock Screw

Lens

Tilting Lock Screw

Dome Cover Separatory Spring

Camera Installation

1. Aim the LG logo of the Dome Camera to face the place that you wish to
watch.

2. Tighten the M4 Tapping Screws to fix the Dome Camera on the ceiling,
then adjust the Pan(Left/ Right) by moving the Pan Base. Tighten the
M4 Tapping Screws after adjustment.

3. Loosen the Tilting Lock Screw. Adjust the Til

t(Up/ Down) by moving the

Tilt Base then tighten Tilting Lock Screw.

4. Loosen the Focus Lock Screw. Adjust the Focus by moving the Focus
Lens then tighten Focus Lock Screw.

5. Install the Dome Cover to the main body by turning it counterclockwise
to the end.

Hole for Fixing

Notes:

• When you install the camera, handle with care. The camera could be dam­aged by improper handling or storage.

• If this camera is mounted on the other places except ceiling, you need an
extra bracket for mounting. (not supplied)

•

When installing the camera with 3.0mm fixed lens, You must note that a black
image on the coner can be made, depending on the angle of the camera.

8

Installation

99

Installation

Camera Connection

Connect the Power Adapter (DC 12V, 300mA; optional) to the Power
Input Jack of the camera as shown below.

Power Input

Jack

Adapter
Jack

Power Adapter
(Not supplied)

Monitor

BNC

10

Installation

Notes:

• When you disassemble the Dome Cover, lift the Dome Cover
Separatory Spring on the opposite side of LG Logo and turn the
Dome Cover clockwise simultaneously.

Dome Cover

Separatory Spring

• When you install the camera, handle with care. The camera
could be damaged by improper handling or storage.

• If this camera is mounted on the other places except ceiling,
you need an extra bracket for mounting.(not supplied)

11

Setup

6-pin Dip Switch Setting

This camera has the 6-pin Dip
Switch for setting.

1. ELC / ALC

ELC (Electronic IRIS), ALC
(Auto IRIS)
The default setting is ELC.

2. FL (Flickerless)

Use for removing the flicker of
picture.
The default setting is OFF.

3. AWB/HOLD

AWB (Auto White Balance),
HOLD (White Balance Hold).
The default setting is AWB.

4. BLC

Backlight compensation elimi­nates strong background light
which makes the camera pic­ture dark such as a spotlight.
You can select the mode for
adjusting the iris lens.
The default setting is OFF.

5. L/L

Not used.

6. AGC (Auto Gain Control)

If the image are too dark,
change the maximum value to
make the image lighter. The
D&N function is activated auto­matically AGC ON mode.
The default setting is ON.

12

Check the following guide for the
possible cause of a problem before
contacting service.

The picture is poor

Does the Dome Cover have lots of
dust on the surface?

- Use a dry cloth to clean the
camera when it is dirty.

Smear may be caused to the
screen of night than daytime.

- Adjust the Focus by moving the
Focus Lens.

Contrast of the screen is not
clear.

Check the condition of the monitor.
A light source such as a spot light
causes burn-in on the display
screen. Adjust position or angle
of the camera to eliminate strong
background light.

Background screen appears
white extremely.

You can set the backlight
compensation to OFF.

Troubleshooting

13

Dimension

76.5mm

ø120

ø100

ø90

26.5mm

14

Specifications

Model LD300P-B/C/D/E/F LD300N-B/C/D/E/F

Signal System PAL NTSC

Total/Effective Pixels 470K/440K 410K/380K

Pick-Up Device 1/3 - inch interline color CCD(Super HAD)

Lens

Fixed Lens
(F=3.0mm (LD300-B), 3.7mm (LD300-C), 6.0mm
(LD300-D), 8.0mm (LD300-E), 12mm (LD300-F))

Angular Field of

View(D)

115° (F=3.0mm), 92°(f=3.7mm), 54°(f=6mm),

38.6°(f=8mm), 25.7°(f=12mm)

Focus Manual

Signal Process Digital Signal Process ( SS11X )

Scanning System 2:1 Interlace

Sync. System Internal

Scanning Frequency 50Hz(VD) 59.94Hz(VD)

Resolution 520 TV Lines

S/N Ratio More than 48dB

Standard Illumination 2000Lux (3200°K)

Minimun Illumination 0.5 Lux

Video Output Signal 1Vp-p Composite (75ohm)

Gain Control Auto

Shutter speed 1/50 ~ 1/10,000 1/60 ~ 1/10000

White Balance Auto / Hold

Back Light Compensation Auto / OFF

1515

Specifications

Model LD300P-B/C/D/E/F LD300N-B/C/D/E/F

Power Source DC 12V

Power Consumption Less than 2.3W

Operating Temp. -10 ºC ~ 50 ºC (Humidity :0%RH ~60%RH)

Storage Temp. -20 ºC ~ 60 ºC (Humidity :0%RH ~85%RH)

Weight 205g

Dimensions 120 (Diameter) x 76.5mm(H)

P/NO: MFL40426675