LG LCD5300R-BN, LCD5300R-BP Owner's Manual

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This lightning flash with arrowhead symbol within an equilateral triangle is
intended to alert the user to the presence of uninsulated dangerous voltage
within the product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the
user to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the product.

WARNING: This product contains chemicals known to the State of California to cause cancer and
birth defects or reproductive harm. Wash hands after handling.

FCC WARNING: This equipment may generate or use radio frequency energy. Changes or
modifications to this equipment may cause harmful interference unless the modifications are
expressly approved in the instruction manual. The user could lose the authority to operate this
equipment if an unauthorized change or modification is made.

REGULATORY INFORMATION: FCC Part 15

This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful interference to radio
communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own expense.

• A suitable conduit entries, knock-outs or glands shall be provided in the cable entries of this
product in the end user.

• Caution: Danger of explosion if battery is incorrectly replaced. Replaced only with the same or
equivalent type recommended by the manufacturer. Dispose of used batteries according to
the manufacturer’s instructions.

• Holes in metal, through which insulated wires pass, shall have smooth well rounded surfaces
or shall be provided with brushings.

This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

Warning: Do not install this equipment in a confined space such as a bookcase or similar unit.

Warning: Wiring methods shall be in accordance with the National Electric Code, ANSI/NFPA 70.

Warning: This is a class A product. In a domestic environment this product may cause radio

interference in which case the user may be required to take adequate measures.

Warning: To reduce a risk of fire or electric shock, do not expose this product to rain or moisture.

Caution: This installation should be made by a qualified service person and should conform to all

local codes.

Caution: To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel
only.

Caution: The apparatus shall not be exposed to water (dripping or splashing) and no objects filled
with liquids, such as vases, shall be placed on the apparatus.

Note:

Please make sure the product is installed appropriate places where secured from flood, such as
under the eaves, to operate properly. This product is certified as IP66 standard. However, if there
is any flood concerns, it is highly recommended to use an outdoor Housing When you install the
camera inside an outdoor Housing, please use one of the following methods:

1. Remove the front glass of Housing before installing the camera.

2. To keep the front glass of Housing, remove the front cover, and then put the camera close to
the front glass.

To disconnect power from mains, pull out the mains cord plug. When installing the product,
ensure that the plug is easily accessible.

LG Electronics hereby declares that this/these product(s) is/are in
compliance with the essential requirements and other relevant
provisions of Directive 2004/108/EC, 2006/95/EC, and 2009/125/EC.

European Standards Centre:

Krijgsman 1, 1186 DM Amstelveen The Netherlands

Disposal of your old appliance

1. When this crossed-out wheeled bin symbol is attached to
a product it means the product is covered by the European
Directive 2002/96/EC.

2. All electrical and electronic products should be disposed of
separately from the municipal waste stream via designated
collection facilities appointed by the government or the local
authorities.

3. The correct disposal of your old appliance will help prevent
potential negative consequences for the environment and
human health.

4. For more detailed information about disposal of your old
appliance, please contact your city office, waste disposal service
or the shop where you purchased the product.

EEE Compliance with Directive. (for Turkey only)

OWNER'S MANUAL

IR Dome Camera

Please read this manual carefully before operating
your set and retain it for future reference.

MODEL

LCD5300R-BN
LCD5300R-BP

Item LCD5300R-BN LCD5300R-BP

Signal System NTSC PAL

Image Device 6 mm (1/3 Type) Exview HAD CCD II

Total/Effective Pixels

Number

520 000 Pixels / 480 000 Pixels 610 000 Pixels / 570 000 Pixels

Horizontal Resolution 650 TV Lines (Color), 700 TV Lines (B/W)

ISP XDI-V

Lens 2.8 mm to 11 mm Vari-focal Lens, F1.2

Minimum

Illumination

(30 IRE)

Color

0.03 lx (Sens-up Off, F1.2), 0.000 3 lx (Sens-up Auto, F1.2),

0.000 1 lx (Sens-up x512, F1.2)

B/W 0 lx (IR LED ON)

Day & Night ICR (AUTO / DAY / NIGHT)

IRIS Control DC

Sync. System Internal / Line Lock

Scanning Frequency

(H/V)

15.734 KHz / 59.94 Hz 15.625 KHz / 50 Hz

S/N Ratio 50 dB

Video Output Signal 1 Vp-p Composite (75 Ω)

IR LED 8 EA

IR Distance 20 m

SmartIR IR Anti-Saturation

BACKLIGHT BLC / HSBLC / OFF

DNR 2D + 3D-DNR

Item LCD5300R-BN LCD5300R-BP

Exposure ALC /ELC

Auto Gain Control OFF/ LOW/ MIDDLE/ HIGH

Electronic Shutter Speed 1/60 to 1/120 000 1/50 to 1/120 000

Digital Zoom x16

Sens-up OFF / AUTO(x2, ... x512)

White Balance AUTO / ATW / ONE PUSH / MANUAL

Privacy Zone Masking 14 Masks

Motion Detection 8 Zones

Digital Effect OFF / V-FILP / MIRROR / ROTATE

Communication Coaxial Communication

Power Source DC 12 V / AC 24 V

Power Consumption 3.5 W

Input Current 290 mA

Operation Temperature/

Humidity

-10 ºC to 50 ºC / 0 % RH to 80 % RH

Storage Temperature/

Humidity

-20 ºC to 60 ºC / 0 % RH to 85 % RH

Dimension (Ø x H) 140 mm x 90 mm

Weight 390 g

Power Supply

This camera must always be operated a DC 12 V or AC 24 V Certified/Listed, class 2 power supply
only.

Handling of the unit

Be careful not to spill water or other liquids on the unit. Be cautions not to get combustible or
metallic material inside the body. If used with foreign matter inside, the camera is liable to fail or to
get cause of fire or electric shock.

• Remove dust or dirt on the surface of the lens with a blower.

• Use a dry soft cloth to clean the body. If it is very dirty, use a cloth dampened with a small

quantity of neutral detergent then wipe dry.

• Avoid the use of volatile solvents such as thinners, alcohol, benzene and insecticides. They
may damage the surface finish and/or impair the operation of the camera. They may damage
the surface finish and/or impair the operation of the camera.

Operating and storage location

Avoid viewing a very bright object (such as light fittings) during an extended period. Avoid
operating or storing the unit in the following locations.

• Extremely hot or cold places (operating temperature -10 °C to 50 °C, however, we
recommend that the unit be used within a temperature range of 0 °C to 45 °C)

• Damp or dust place

• Places exposed to rain

• Places subject to strong vibration

• Close to generators of powerful electromagnetic radiation such as radio or TV

transmitters.

Important Safety Instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug
has two blades with one wider than the other. A grounding type plug has two blades and
a third grounding prong. The wide blade or the third prong are provided for your safety. If
the provided plug does not fit into your outlet, consult an electrician for replacement of the
obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or
sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus
combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.

Specification

1. Using the template as a guide, make a hole through the ceiling.

FRONT

PRODUCT CENTER POSITION

MEZ62687703

n

100 Cutting Line

4 Place

SELFTAPPING SCREW

CABLE HOLE (LCV5300)

CABLE HOLE (LCD5300)

FRONT

PRODUCT CENTER POSITION

MEZ62687703

n

100 Cutting Line

4 Place

SELFTAPPING SCREW

CABLE HOLE (LCV5300)
CABLE HOLE (LCD5300)

FRONT

PRODUCT CENTER POSITION

MEZ62687703

n

100 Cutting Line

4 Place

SELFTAPPING SCREW

CABLE HOLE (LCV5300)

CABLE HOLE (LCD5300)

FRONT

PRODUCT CENTER POSITION

MEZ62687703

n

100 Cutting Line

4 Place

SELFTAPPING SCREW

CABLE HOLE (LCV5300)

CABLE HOLE (LCD5300)

2. Install the camera mounting bracket to the ceiling.

FRONT

PRODUCT CENTER POSITION

MEZ62687703

n

100 Cutting Line

4 Place

SELFTAPPING SCREW

CABLE HOLE (LCV5300)

CABLE HOLE (LCD5300)

FRONT

PRODUCT CENTER POSITION

MEZ62687703

n

100 Cutting Line

4 Place

SELFTAPPING SCREW

CABLE HOLE (LCV5300)

CABLE HOLE (LCD5300)

3. Connect the cables to the cable jacks of the camera body.

FRONT

PRODUCT CENTER POSITION

MEZ62687703

n

100 Cutting Line

4 Place

SELFTAPPING SCREW

CABLE HOLE (LCV5300)

CABLE HOLE (LCD5300)

FRONT

PRODUCT CENTER POSITION

MEZ62687703

n

100 Cutting Line

4 Place

SELFTAPPING SCREW

CABLE HOLE (LCV5300)

CABLE HOLE (LCD5300)

FRONT

PRODUCT CENTER POSITION

MEZ62687703

n

100 Cutting Line

4 Place

SELFTAPPING SCREW

CABLE HOLE (LCV5300)

CABLE HOLE (LCD5300)

4. Assemble the camera and mounting bracket as illustrated step

a and b.

FRONT

PRODUCT CENTER POSITION

MEZ62687703

n

100 Cutting Line

4 Place

SELFTAPPING SCREW

CABLE HOLE (LCV5300)

CABLE HOLE (LCD5300)

FRONT

PRODUCT CENTER POSITION

MEZ62687703

n

100 Cutting Line

4 Place

SELFTAPPING SCREW

CABLE HOLE (LCV5300)

CABLE HOLE (LCD5300)

FRONT

PRODUCT CENTER POSITION

MEZ62687703

n

100 Cutting Line

4 Place

SELFTAPPING SCREW

CABLE HOLE (LCV5300)

CABLE HOLE (LCD5300)

FRONT

PRODUCT CENTER POSITION

MEZ62687703

n

100 Cutting Line

4 Place

SELFTAPPING SCREW

CABLE HOLE (LCV5300)

CABLE HOLE (LCD5300)

Installation

1. Connect a portable monitor to the video jack.

2. Adjust the Pan/Tilt/Rotate position of the camera.

TILT

PAN

ROTATE

3. Adjust the zoom.

TILT

PAN

ROTATE

FAR

NEAR

WIDE

TELE

4. Adjust the focus.

FAR

NEAR

Camera Adjustment

OSD Menu control buttons

This camera utilizes an on-screen user MENU. To set items on the menu, use the
following buttons.

LEFT

UP

RIGHT

SET

DOWN

BUTTON Description

UP Used to move upper direction on the menu screen. Use this

button to select an item or adjust the parameters.

DOWN Used to move lower direction on the menu screen. Use this

button to select an item or adjust the parameters.

RIGHT Moves the cursor to the right. Used to increment the value

selected in the menu. The parameter changes each time this
button is pressed.

LEFT Moves the cursor to the left. Used to decrement the value

selected in the menu. The parameter changes each time this
button is pressed.

SET Executes selections and displays a submenu for an item with

the

mark.

Exposure Settings

You can set the exposure options using the
EXPOSURE menu.

1. Select [EXPOSURE] option on the [CAMERA
SETTING] menu.

2. Use [LEFT] or [RIGHT] button to select a mode.

3. Press [SET] button and the EXPOSURE menu
appears.

NOTE:

Set the Shutter OFF when Color Rolling occurs in the
indoor scene. Recommend the Shutter Auto in the
outdoor scene.

White Balance settings

Select the method by which the camera shifts its
output colors to compensate for the color of a light
source.

1. Select [WHITE BAL] option.

2. Use [LEFT] or [RIGHT] button to select a mode
then press [SET].

Day/Night Setting

1. Select [DAY/NIGHT] option.

2. Use [LEFT] or [RIGHT] button to select mode for
Day/Night function.

NOTE:

If you set the AGC to [OFF] on the [EXPOSURE] menu,
the AUTO mode of the DAY/NIGHT function is not
available and [---] mark is displayed.-

SmartIR Setting

SettingSmartIR function improve the sensitivity in
the low luminance. SmartIR analyze the image of
the screen, when a subject is close. Then SmartIR
reduce the IR LED brightness and gain to prevent
saturation of the closed subject.

1.

Select [SmartIR] option.

2.

Use [UP] or [DOWN] to select an option then

use [LEFT] or [RIGHT] button to adjust the
option.

Motion Detection Setting

The motion detection detects the
moving objects in the scene by monitoring changes
in brightness level. You can select the level of
sensitivity for motion detection to 8 zone.

1. Select [MOTION DET] option.

2. Use [LEFT] or [RIGHT] button to select a [ON]
and press [SET]. The MOTION DETECTION menu
appears.

3D-DNR Setting

1. Select [3D-DNR] option. If pictures are not clear
due to brightness, this option would reduce the
noise of picture.

2. Use [LEFT] or [RIGHT] button to select a value.

Privacy Mask Setting

This function is aiming at the protection of personal
privacy, selecting a screen part black not to be
displayed in the screen. Up to 8 zones can be
registered.

1. Select [PRIVACY] option.

2. Use [LEFT] or [RIGHT] button to select a [ON]
and press [SET]. The PRIVACY SETUP menu
appears.

NOTE:

You can adjust the mask color manually except for COLOR 8.

Special Menu Settings

This menu lets you adjust and set up D-ZOOM,
D-EFFECT, SHARPNESS, COLOR, SYNC, USER TITLE,
LANGUAGE function by yourself in the SPECIAL menu.

1. Select [SPECIAL] option.

2. Press [SET] button and the SPECIAL menu
appears.

SYSTEM Setting

1. Select the [SYSTEM] menu.

2. Press [SET] button and the SYSTEM menu
appears.

3. Use [UP] or [DOWN] button to select the option.

• FACTORY RESET: To reset the camera

setting to factory setting, select the
[FACTORY RESET] option.

4. Press [SET] button to confirm your selection.

NOTE:

The menu screen is move to top menu, after set up
[Factory Reset].

Operation

NOTE:

Disassemble the IR cover as
illustrated in case of difficult
occasion to adjust the focus
lever.

NOTE:

Disassemble the IR cover as
illustrated in case of difficult
occasion to adjust the zoom
lever.