LG L1972HS Users manual

Test Report No.: GETEC-E3-07-044 FCC Class B Certification

APPENDIX H

: USER’S MANUAL

EUT Type: 19” LCD Monitor

FCC ID: BEJL1972HS

User’s Guide

L1972H

Make sure to read the Important Precautions before using this product.

Keep the User's Guide (CD) in an accessible place for future reference.

See the attached label on the unit and show this information to your dealer

when asking for service.

Important Precautions

This unit has been engineered and manufactured to ensure your personal safety, however improper use may result in potential electrical shock or fire hazards. In order to allow the proper operation of all safeguards incorporated in this display, observe the following basic rules for its installation, use, and servicing.

On Safety

Use only the power cord supplied with the unit. In case you use another power cord, make sure that it is certified by the applicable national standards if not being provided by the supplier. If the power cable is faulty in any way, please contact the manufacturer or the nearest authorized repair service provider for a replacement.

The power supply cord is used as the main disconnection device. Ensure that the socket-outlet is easily accessible after installation.

Operate the display only from a power source indicated in the specifications of this manual or listed on the display. If you are not sure what type of power supply you have in your home, consult with your dealer.

Overloaded AC outlets and extension cords are dangerous. So are frayed power cords and broken plugs. They may result in a shock or fire hazard. Call your service technician for replacement.

Do not Open the Display.

There are no user serviceable components inside. There are Dangerous High Voltages inside, even when the power is OFF. Contact your dealer if the display is not operating properly.

To Avoid Personal Injury :

Do not place the display on a sloping shelf unless properly secured. Use only a stand recommended by the manufacturer. Do not drop an object on or apply impact to the product. Do not throw any toys or objects on the pro duct screen. It can cause injury to human, problem to product and damage the display.

To Prevent Fire or Hazards:

Always turn the display OFF if you leave the room for more than a short period of time. Never leave the display ON when leaving the house. Keep children from dropping or pushing objects into the display's cabinet openings. Some internal parts carry hazardous voltages. Do not add accessories that have not been designed for this display. When the display is to be left unattended for an extended period of time, unplug it from the wall outlet. In the presence of thunder and lightning, never touch the power cord and signal cable because it can be very dangerous. It can cause electric shock.

Important Precautions

On Installation

Do not allow anything to rest upon or roll over the power cord, and do not place the display where the power cord is subject to damage.

Do not use this display near water such as near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool. Displays are provided with ventilation openings in the cabinet to allow the release of heat generated during operation. If these openings are blocked, built-up heat can cause failures which may result in a fire hazard. Therefore, NEVER:

Block the bottom ventilation slots by placing the display on a bed, sofa, rug, etc. Place the display in a built-in enclosure unless proper ventilation is provided. Cover the openings with cloth or other material. Place the display near or over a radiator or heat source. Main power breaker is the power cord and this breaking device must be located at a location where it is easy to operate.

Do not rub or strike the Active Matrix LCD with anything hard as this may scratch, mar, or damage the Active Matrix LCD permanently.

Do not press the LCD screen with your finger for a long time as this may cause some afterimages.

Some dot defects may appear as Red, Green or Blue spots on the screen. However, this will have no impact or effect on the display performance.

If possible, use the recommended resolution to obtain the best image quality for your LCD display. If used under any mode except the recommended resolution, some scaled or processed images may appear on the screen. However, this is characteristic of the fixed-resolution LCD panel.

On Cleaning

Unplug the display before cleaning the face of the display screen. Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the display

screen because over-spraying may cause electrical shock.

On Repacking

Do not throw away the carton and packing materials. They make an ideal container in which to transport the unit. When shipping the unit to another location, repack it in its original material.

On Disposal

The fluorescent lamp used in this product contains a small amount of mercury. Do not dispose of this product with general household waste.

Disposal of this product must be carried out in accordance to the regulations of your local authority.

Connecting the Display

Unfolding the stand base

Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. For the desktop monitor, install the computer with the stand unfolded, for Wall mounte plate, install the computer with the stand folded.

Place the monitor with its front facing downward on a soft cloth.

2. Hold the monitor as shown, and then lift it up slightly.

Pull out the stand as shown in the picture and the stand will hold up.

Place the monitor upright and adjust the stand base to the desired angle. Adjust the stand base's angle by holding the edges of the monitor gently with both hands.

1. This illustration depicts the typical connection procedure. Your monitor may differ from the one displayed in the pictures above.

2. Do not touch or apply force to the monitor's screen while expanding or folding the stand base.

The Head part

Connecting the Display

Folding the stand base

Face the front of the monitor dislpay. Than gently push the monitor backwards, following the sequence shown in the picture below.

Tilt range

Make sure that the angle of the panel is set for your comfort.

Tilt Range : 0˚~30

Ergonomic

It is recommended that in order to maintain an ergonomic and comfortable viewing position, the forward tilt angle of the monitor should not exceed 5 degrees

Connecting the Display

To adjust the height

Height Range : maximum 4.02 inches (100 mm)

102 mm

NOTE

When the monitor is at maximum height, it may slide down slightly due to the

elasticity of the spring.

Connecting the Display

Using the Computer

Make sure to turn off the computer and product. Connect the cable as below sketch map

form to .

Connect DVI Cable Connect Dsub Cable (PC)

Connect Dsub Cable (Mac)

Power Cord

Wall-outlet type

PC-outlet type

For Apple Macintosh use, a separate plug adapter is needed

to change the 15 pin high density (3 row) D-sub VGA

connector on the supplied cable to a 15 pin 2 row connector.

Signal Cable

Varies according to model.

Mac adapter

MAC

NOTE

This is a simplified representation of the rear view.

This rear view represents a general model; your display may differ from the view as shown.

Press button on the side switch panel to turn the power on. When monitor power is turned on, the

'Self Image Setting Function' is executed automatically.

(Only Analog Mode)

NOTE

‘ Self Image Setting Function’? This function provides the user with optimal display settings.When the user

connects the monitor for the first time, this function automatically adjusts the display to optimal settings for individual input signals. If you want to adjust the monitor while in use, or wish to manually run this function once again, push the ‘AUTO/SET’ button on the side panel of the monitor. Otherwise, you may execute the ‘ Factory reset’ option on the OSD adjustment menu. However, be aware that this option initializes all the menu items except ‘Language’.

Control Panel Functions

Front Panel Controls

Bottom

Control Function

ZOOMING

The resolutions at which the EZ ZOOMING operates are as follows: For the 19 inch monitor, 1280 x 1024, 1024 x 768, 800 x 600 The setting method can differ by O/S or video card. In this case, Please ask to the computer or the video card manufacturer.

MENU Button

At the current display, Use 'ez Zooming' Key, then the display resolution is transferred to the one step low resolution. Use 'ez Zooming' Key one more, the display is back to the original display.

*Only One touch of ez-zoom, you can fine the best resolution you want and it is possible to magnify the size of characters and pictures for the old not having good eye sight, housewives not dealing with computer well and children.

Use this button to enter or exit from the On Screen Display.

OSD LOCKED/UNLOCKED

This function allows you to lock the current control settings, so that these settings are not inadvertently changed. To lock the OSD settings, press and hold the

MENU button for several seconds. The message "OSD LOCKED" appears.

You can unlock the OSD settings at any time by pushing the MENU button for several seconds. The message "OSD UNLOCKED" appears.

Control Panel Functions

Control Function

- +

Buttons

Button

( )

Button

(SOURCE Hot key)

AUTO/SET Button

Use these buttons to select or adjust functions in the On Screen Display.

For more information, refer to page A14.

Use this button to make either D-Sub or DVI connector active. This feature is used when two computers are connected to the display. The default setting is D-Sub.

Use this button to selection an icon in the On Screen Display.

AUTO IMAGE ADJUSTMENT

When adjusting your display settings, always press the AUTO/SET button prior to entering the On Screen Display(OSD). This will automatically adjust your display image to the ideal settings for the current screen resolution size (display mode).

The best display mode is 19 inch monitor : 1280 x 1024

Power Button

Power Indicator

Use this button to turn the display on or off.

This Indicator lights up as blue when the display is operating normally(On Mode). If the display is in Sleep Mode (Energy Saving), this indicator color will changes to amber.

On Screen Display (OSD) Control Adjustment

AUTO/SET

MENU MENU

Screen Adjustment

Making adjustments to the display's image size, position and operating parameters is quick and easy with the On Screen Display Control system(OSD). A short example is given below to familiarize you with the use of the controls. The following section is an outline of the available adjustments and selections you can make by using the OSD.

NOTE

Allow the display to stabilize for at least 30 minutes before making any image adjustments.

To make adjustments in the On Screen Display, follow these steps:

Press the MENU button, then the main menu of the OSD appears.

To select each item in the OSD menu, use the or button. When the icon you want is highlighted, press the AUTO/SET Button.

Use the / buttons to adjust the image to the desired level. Use the

AUTO/SET button to select other sub-menu items.

Press the MENU buttononce to return to the main menu to select another function. Press the MENU buttontwice to exit from the OSD.

+ 24 hidden pages