LG H27H49S Service Manual
zenith
SERVICE MANUAL SERVICE MANUAL
Product Type:
Chassis:
Manual Part #:
Model Line:
Product Year:
Presentation Series
DIGITAL FCS
3828VD0171G
H
2006
Model Series:
H27H49S
H32H49S
Printed in U. S. A.
CONTENTS
General Information/Remote Controls................................
Installer’s Menu ............................................................
Servicing/Trobleshooting ................................................
Model/Module Parts List .................................................
Exploded Views .............................................................
Schematics ...................................................................
Published by
Technical Publications
Zenith Electronics Corporation
P. O. Box 240007
Huntsville, Al 35824
Copyright May 2006 by Zenith Electronics Corporation ©
1
2
3
4
5
6
PRODUCT SAFETY SERVICING GUIDELINES FOR AUDIO-VIDEO PRODUCTS
A
IMPORTANT SAFETY NOTICE
This Manual was prepared for use only by properly trained audio-visual service technicians.
When servicing this product, under no circumstances should the original design be modified
or altered without permission from Zenith Electronics Corporation. All components should be
replaced only with types identical to those in
the original circuit and their physical location, wiring and lead dress must conform to
original layout upon completion of repairs.
Special components are also used to prevent xradiation, shock and fire hazard. These components are indicated by the letter “x” included
in their component designators and are required
to maintain safe performance. Zenith Electronics Corporation allows no deviations without
prior approval. Circuit diagrams may occasionally differ from the actual circuit used. This
way, implementation of the latest safety and
performance improvement changes into the set is
not delayed until the new service literature is
printed.
CAUTION: Do not attempt to modify this product
in any way. Never perform customized installations without manufacturer’s approval. Unauthorized modifications will not only void the warranty, but may lead to property damage or user
injury.
Service work should be performed only
after you are thoroughly familiar with these
safety checks and servicing guidelines.
Graphic symbols
SERVICE INFORMATION
While servicing, use an isolation transformer
for protection from AC line shock. After the
original service problem has been corrected,
make a check of the following:
FIRE AND SHOCK HAZARD
1. Be sure that all components are positioned to
avoid a possibility of adjacent component shorts.
This is especially important on items transported to and from the repair shop.
2. Verify that all protective devices such as
insulators, barriers, covers, shields, strain
reliefs, power supply cords, and other hardware
have been reinstalled per the original design.
Be sure that the safety purpose of the polarized
line plug has not been defeated.
3. Soldering must be inspected to discover possible cold solder joints, solder splashes, or
sharp solder points. Be certain to remove all
loose foreign particles.
4. Check for physical evidence of damage or
deterioration to parts and components, for frayed
leads or damaged insulation (including the AC
cord), and replace if necessary.
5. No lead or component should touch a receiving
tube or a resistor rated at 1 watt or more. Lead
tension around protruding metal surfaces must
be avoided.
6. After re-assembly of the set, always perform
an AC leakage test on all exposed metallic parts
of the cabinet (the channel selector knobs, antenna terminals, handle and screws) to be sure
that set is safe to operate without danger of
electrical shock. DO NOT USE A LINE ISOLATION
TRANSFORMER DURING THIS TEST. Use an AC voltmeter having 5000 ohms per volt or more sensitivity in the following manner: Connect a 1500 ohm,
10 watt resistor, paralleled by .15 mfd 150V AC
type capacitor between a known good earth ground
(water pipe, conduit, etc.) and the exposed metallic parts, one at a time. Measure the AC
voltage across the combination of 1500 ohm resistor and .15mfd capacitor. Reverse the AC plug
by using a non-polarized adaptor and repeat AC
voltage measurements for each exposed metallic
part. Voltage measured must not exceed 0.75 volts
RMS. This corresponds to 0.5 milliamp AC. Any
value exceeding this limit constitutes a potential shock hazard and must be corrected immediately.
The exclamation point within an equilateral triangle is intended to alert the
service personnel to important safety
information in the service literature.
The lightning flash with arrowhead symbol within an equilateral triangle is
intended to alert the service personnel
to the presence of non-insulated “dangerous voltage” that may be of sufficient magnitude to constitute a risk of
electric shock.
The pictorial representation of a fuse
and its rating within an equilateral triangle is intended to convey to the service personnel the following fuse replacement caution notice:
CAUTION: FOR CONTINUED PROTECTION AGAINST
RISK OF FIRE, REPLACE ALL FUSES WITH THE
SAME TYPE AND RATING AS MARKED NEAR EACH
FUSE.
.C. Voltmet e r
Good Earth Ground
such as the Water
Pipe, Conduit, etc.
X-RADIATION
1. Be sure procedures and instructions to all
service personnel cover the subject of x-radiation. The only potential source of x-rays
in current TV receivers is the picture tube.
However, this tube does not emit x-rays when
the HV is at the factory-specified level. The
proper value is given in the applicable schematic. Operation at higher voltages may cause
a failure of the picture tube or high-voltage
supply and, under certain circumstances may
produce radiation in excess of desirable levels.
2. Only factory-specified CRT anode connectors
must be used.
3. It is essential that the service personnel
have available an accurate and reliable highvoltage meter.
4. When the high-voltage circuitry is operating
properly, there is no possibility of an xradiation problem. Every time a color chassis
is serviced, the brightness should be run up
and down while monitoring the high voltage
with a meter, to be certain that the high
voltage does not exceed the specified value
and that it is regulating correctly.
5. When troubleshooting and making test measurements in a product with a problem of excessively high voltage, avoid being unnecessarily close to the picture tube and the high
voltage power supply. Do not operate the product longer than necessary to locate the cause
of excessive voltage.
6. Refer to HV, B+, and shutdown adjustment
procedures described in the appropriate schematics and diagrams (where used).
IMPLOSION
1. All direct view picture tubes are equipped
with an integral implosion protection system;
take care to avoid damage during installation.
2. Use only the recommended factory replacement
tubes.
TIPS ON PROPER INSTALLATION
1. Never install any receiver in a closed-in
recess, cubbyhole, or closely fitting shelf
space over, or close to, a heat duct, or in the
path of heated air flow.
2. Avoid conditions of high humidity such as:
outdoor patio installations where dew is a
factor, near steam radiators where steam leakage is a factor, etc.
3. Avoid placement where draperies may obstruct
venting. The customer should also avoid the
use of decorative scarves or other coverings
that might obstruct ventilation.
4. Wall- and shelf-mounted installations using
a commercial mounting kit must follow the factory-approved mounting instructions. A product mounted to a shelf or platform must retain
its original feet (or the equivalent thickness
in spacers) to provide adequate airflow across
the bottom. Bolts or screws used for fasteners
must not touch any parts or wiring. Perform
leakage tests on customized installations.
5. Caution customers against mounting a product
on a sloping shelf or in a tilted position,
unless the receiver is properly secured.
6. A product on a roll-about cart should be
stable in its mounting to the cart. Caution
the customer on the hazards of trying to roll
a cart with small casters across thresholds or
deep pile carpets.
7. Caution customers against using a cart or
stand that has not been listed by Underwriters
Laboratories, Inc. for use with its specific
model of television receiver or generically
approved for use with TVs of the same or larger
screen size.
8. Caution customers against using extension
cords. Explain that a forest of extensions,
sprouting from a single outlet, can lead to
disastrous consequences to home and family.
0.15uF
1500 OHM
10 WATT
Place this probe
on each exposed
metal part.
3828VD0171G i DIGITAL FCS - SAFETY
PRODUCT SAFETY SERVICING GUIDELINES FOR AUDIO-VIDEO PRODUCTS
X-RADIATION
To prevent possible exposure to X-Radiation caused
by excessive CPT anode voltage, The Digital FCS
chassis incorporate a ¨High Voltage Shutdown¨
circuit. This circuit senses the level of a
Shutdown pulse from the ¨Flyback Transformer¨
representative of the actual high voltage on the
CPT anode. When this level exceeds a predetermined voltage, the circuit shuts down the horizontal drive, preventing further generation of
anode voltage. In this condition, the horizontal drive is latched off.
SHUTDOWN CIRCUIT OPERATION
The shutdown pulse voltage from pin 9 of TX3201
(Fly-Back Transformer) is peak detected (rectified) by the action of diode D3205 and capacitor
C3218. This form a DC voltage appearing on C3218
representative of the CPT anode voltage (HV)
produced by TX3201. This DC voltage is divided
down by the voltage divider series circuit of
precision resistors R3001 (with in parallel provision for R3002) and R3003 (also with in parallel provision for R3004). This divider output
voltage appears on Emitter of Q3000. In the
event that the CPT anode voltage becomes excessive, the voltage in Emitter of Q3000 will be
higher than the voltage in the Base of Q3000
(5.1V Base voltage is fixed by ZD3003) and therefore Q3000 enters in conduction mode. Therefore
a DC voltage will appear on R3005 and this voltage will put D3000 in conduction. The D3000
cathode voltage level (close to 5V, a ¨logical
high¨) is sent to pin 34 (HPROT input) of video
processor ICM2200 stopping the Horizontal Drive
Output (H-DRV pin 40) pulse train therefore shutting down to Horizontal Output Fly-Back transformer. switching off the HV and horizontal de-
flection. If the shutdown condition disappears,
the TV set can be turned-on only if the AC is
interrupted for about 20 Seconds and then the
on/off switch is activated.
CPT ANODE HIGH VOLTAGE MEASUREMENT PROCEDURE
Each CPT screen size has it´s own safe operating
anode and shutdown voltage. Critical safety component (designated with and ´X´ in the component
designator) are designed to operate the CPT at a
safe operating anode voltage and provide proper
shutdown thresholds. If replacement of any of
these components is deemed necessary, it is important to use original type LGERS components.
After replacement is made, confirm proper anode
voltage using the following procedure.
Measurement of the CPT anode voltage must be
performed using a high impedance-high voltage
meter, with no raster on the screen, and operating at nominal horizontal frequency 37.9 kHz.
(This TV internally up-converts the video signal horizontal frequency from the 15,734 Hz of
NTSC to 37.9 kHz of SVGA for displaying).
After discharging the CPT, connect a high impedance-high voltage meter to the CPT anode. Turn
the television ón´ and confirm a good signal is
being displayed. Reduce Brightness and Contrast
settings until the picture is well extinguished.
Observe the anode voltage meter reading and compare with the table below fro the proper CPT
screen size. If the voltage reading is higher
than the maximum, verify circuit component val-
ues and proper operation.
CRT Screen
Size
27”
32”
CRT Anode Voltage
Nominal Anode Voltage
(KV)
30 ± 1.0
30 ± 1.0
Min. Shutdown Voltage
Max. Shutdown Voltage
(KV)
Nominal HV + 2 36
Nominal HV + 2 36
(KV)
3828VD0171G ii DIGITAL FCS - SAFETY
INSTALLER MENU
INSTALLER MENU
Use the Installer Menu to set up or change operational settings. See descriptions of the Installer items on the following pages.
ACCESSING THE INSTALLER’S MENU
Installer’s menu items can be accessed by using
the optional LP702 installer’s remote control.
Just press and hold MENU (about 8 seconds) until
the display changes, then press 9, 8, 7, 6, then
ENTER. To exit the Installer’s Menu, press ENTER
again. Any changes you make will be stored in
nonvolatile memory.
The Installer’s menu opens with item 0-I,
INST. SEQ. Use the SELECT key to sequence
through the available menu items. Or, access an
item directly by entering the item number, then
pressing MENU. For example, to access the Sleep
Timer option which is item 15-I, press 1, 5,
then MENU. To change a setting use the Left/
Right ADJ keys.
USING THE INSTALLER’S MENU
Using the Installer’s Menu Items 0-I - 89-I are
accessible only in the Installer’s Menu. Their
numbers, descriptions, ranges, factory default
settings, and a place for listing any changes
made onsite are given below and on the following
pages. The Factory Menu that is intended for
qualified service technicians only, is not shown
(XX-F items). Normally Factory menu items do not
require adjustment.
00-I INSTALLER SEQ 0
SN: FFFF-FFFFFFFF
UPN: 255-255-255-255
D2 <-> MICRO COMM STA TUS OK
Typical Installers Menu
Detailed Descriptions of Installer Menu Items
0-I. INSTALLER SEQUENCE Gives access to In-
staller Menu depending on the code selected.
0 = 9876 1 = 4321
2 = 1478 3 = 3698
1-I. POWER MANAGE (Power Management)
Determines hours of no activity before automatic shutoff. The POWER MANAGE function is for
saving energy. When set to 0, Power Manage is
OFF. Settings range from 0 - 7, with 1 - 7
representing the hours that the TV will remain
on, unless there has been activity from the
front control panel or remote control.
2-I. AC ON (AC Power Switchable)
Allows the TV to turn ON just by applying AC
power. Pressing the POWER button is not necessary. This is desirable when the TV is plugged
into a cable box or a power outlet controlled by
a wall switch. Use ADJUST to select 0 or 1,
where 0 is the default is OFF, and 1 is ON.
NOTE: When set to 1 (ON), the TV does not respond to POWER On/Off commands from either the
remote or the TV front control panel, and the
SLEEP TIMER is also nonfunctional.
3-I. BAND/AFC (Band/Automatic Frequency Control)
There are 8 possible settings for this option:
0 = Broadcast Fixed 4 = Broadcast AFC
5 = CATV Fixed 1 = CATV AFC
6 = HRC Fixed 2 = HRC AFC
7 = ICC Fixed 3 = ICC AFC
Channels are accessed faster when fixed modes
are used. The AFC (search modes) should only be
used when some channels are not on nominal frequencies.
NOTE: BAND is automatically set by AUTO PROGRAM.
If some channels were not found by AUTO PROGRAM,
select the appropriate AFC setting here and add
the channels using the ADD/DEL option in the
Setup Menu.
4-I. STRT CHANNEL (Start Channel)
When active, this function allows you to determine the initial channel number when the TV is
turned ON. This feature is useful for an inhouse information channel, since the TV would
always select that channel when it is turned on.
Setting this to 255 causes the last channel
viewed when TV was turned off to be the tuned to
channel when the TV is turned on again.
The range of values is 0 - 255. Use ADJ (adjust)
keys to choose numbers that determine the start
channel.
5-I. CHAN LOCK (Channel Lock)
CHAN LOCK is ideal if a cable box (or similar)
is the sole source for programming—and the TV
must always be on the same channel. Changing
channels with Channel Up/Down or keypad numbers
is impossible. Channel Lock is inactive when set
to 0 (default).
Generally, this feature is used in conjunction
with START CHANNEL (item 4-I.) where the start
channel may, for example, be set to 3 or 4. If
the start channel is 3, then the TV will remain
on channel 3. then the TV will remain on channel
3. NOTE: When CHANNEL LOCK is active and is
active and CHANNEL OVERIDE is disabled, AUTO
PROGRAM is not functional.
6-I. GHOST CH (Ghost Channel)
When set to 1, the current channel number is
displayed in the upper right corner of the CRT.
The number moves slightly to prevent damage to
the screen. The default is “0” or OFF. NOTE:
When captions are on, “Ghost Channel” is not
displayed.
3828VD0171G 2-1 DIGITAL FCS - INSTALLER MENU
INSTALLER MENU
7-I. START VOLUME
This function allows the Installer to determine
the initial volume select that volume level when
it is turned on. The range of values are 0 - 63,
255. If 255 is selected, the current volume
level will be retained in memory when the TV is
turned off; at TV turn on, volume level is automatically set to the previous or last level.
8-I. MIN VOLUME (Minimum Volume)
This function determines the minimum volume level
allowable with the VOLUME (VOL) Up/Down control. In this way, for example, someone cannot
set the sound too low to hear. The range is from
0 to 63—change values with ADJ (adjust). The
factory default is 0, which provides full range
of volume control. It may be best to set the
same value on every TV.
NOTE: The minimum volume level cannot have a
value setting higher than in the MAX VOLUME
level (described below).
9-I. MAX VOLUME (Maximum Volume)
This function determines the maximum volume level
allowable with the VOLUME Up/Down control. In
this way, for example, someone cannot set the
sound level high enough to disturb others.
The range is 0 to 63, with 63 as the default
which gives the user the full range of volume
control. Change values with ADJUST keys. It may
be best to set the same value on every TV.
NOTE: The maximum volume level cannot have a
value setting lower than the MIN VOLUME level
(described above).
10-I. MUTE DISABLE
Enables or disables sound mute function. If set
to 1, sound cannot be muted. If set to 0, sound
can be muted.
11-I. KEY DEFEAT (Keyboard Defeat)
When set to 1, it prevents the end user from
accessing screen menus with the front panel—
MENU, SELECT, and ADJUST do not function. When
set to 0, those keys are functional. The menus
can always be accessed with MENU on the remote.
12-I. NOT USED
13-I. NOT USED
14-I. NOT USED
15-I. SLEEP TIMER
When set to 1, the Sleep Timer feature is available to the user (but no message is displayed
prior to turn-off). When set to 0, the Sleep
Timer is not functional.
16-I. EN. TIMER (Enable Timer)
Set to 1, On/Off Timer functions are available
to user. Set to 0 to disable On/Off Timer functions.
Note: Clock must be set in order to use Timers.
17-I. ALARM
Gives you the option of making the alarm function available to the user. Set to 1, Alarm
function is available to user. Set to 0 to disable the Alarm function.
Note: Clock must be set in order to set the
Alarm.
18-I. NOT USED
19-I. NOT USED
20-I. FEATURE LEVEL
Default set to ZEN 1 for Zenith IR remote control operation. Set O, P LBL for Zenith Private
Label IR remote control operation.
Warning: Note: Installer should leave Item 20-I
FEATURE LEVEL set to 1 (default). Do not
set to “0” or remote will not control TV.
21-I. V-CHIP
Set to 1 to activate V-Chip (Parental Control);
have it available to user to filter or control
and restrict viewable program content. Set to 0
to turn V-Chip feature off, not available to
user; no programming
restrictions can be set.
22-I. MAX BLK HRS (Maximum Blocking Hours)
Set 0 to 99 for the maximum V-Chip (Parental
Control) block hours. Default setup is 12 blocking hours.
23-I. CAPTION LOCK
Set to 1 to restore previous Caption On/Off
state after TV turns off. When set to 0, Captions are always off, when TV is initially turned
on.
24-I. TEXT MODE
Determines whether TEXT 1, TEXT 2, TEXT 3, or
TEXT 4 decoding is enabled when TEXT is turned
on (either from the Setup Menu or directly with
CC on the remote).
TIP: Set Text Mode to 1 only if text is offered
in your video system.
25-I. FUNCTION PRE. (Function Preview)
Set to 0 to suppress CHANNEL PREVIEW from the
FUNCTION menu with some Pay-Per-View systems.
26-I. NOT USED
27-I. NOT USED
28-I. CH. OVERRIDE (Channel Override)
When set to 1, the user can select channels with
either CHANNEL Up/Down or by direct keypad entry. When set to 0, only those channels that are
entered for scanning may be selected by direct
keypad entry.
3828VD0171G 2-2 DIGITAL FCS - INSTALLER MENU
INSTALLER MENU
Note: If set to 0, Auto program is locked; (as
shown on Setup menu) channel search is not avail-
able.
29-I. OLD OCV (On Command VideoTM)
Set to 1 for operation with systems from On
Command
Corporation.
30-I. ACK MASK
M.P.I. Communication Parameter. Leave at default setting unless changed by Pay-Per-View
provider.
31-I. POLL RATE
M.P.I. Communication Parameter. Leave at default setting unless changed by Pay-Per-View
provider.
32-I. TIMING PULSE
M.P.I. Communication Parameter. Leave at default setting unless changed by Pay-Per-View
provider.
33-I. NOT USED
34-I. CAMPORT ENABLE
Set to 1 to enable the front AUX (Camport) input.
Set to 0 to disable front AUX input.
35-I. NOT USED
36-I. NOT USED
37-I. REAR Y/C EN. (Rear S-Video Enable)
Set to 1 to enable the rear S-Video input.
Set to 0 to disable the rear S-Video input.
45-I. NOT USED
46-I. STRT AUX SRCE (Starting Aux Source)
Sets the starting AUX source.
47-I. AUX STATUS
Set to 1 for M.P.I. AUX source to be reported as
a channel number instead of channel 0. Set to 0
to disable AUX identification change.
48-I. DIS. SETUP M. (Disable Setup Menu)
Set to 1 to disable the Setup menu. Setup menu
will not appear. Set to 0 to enable the Setup
menu.
49-I. DIS. AUDIO M. (Disable Audio Menu)
Set to 1 to disable the Audio menu. Audio menu
will not appear. Set to 0 to enable the Audio
menu.
50-I. DIS. VIDEO M. (Disable Video Menu)
Set to 1 to disable the Video menu. Video menu
will not appear. Set to 0 to enable the Video
menu.
51-I. DIS. VCHIP M. (Disable Parental Control Menu)
Set to 1 to disable V-Chip menu. V-Chip menu
will not appear. Set to 0 to enable the V-Chip
menu.
52-I. DIS. SOURCE M (Disable Source Menu)
Set to 1 to disable Source menu. Source menu
will not appear. Set to 0 to enable the Source
menu.
53-I. DIS. CH-TIME (Disable Channel-Time Display)
Set to 1 to disable the Channel-Time display.
Channel-Time display will not appear. Set to 0
to enable the Channel-Time display.
38-I. NOT USED
39-I. NOT USED
40-I. AUTO CAMPORT
Set to 1 to automatically switch to Camport when
equipment is connected to front Video input.
Set to 0 to disable front Video automatic source
selection.
54-I. EN. SET. COL. (Enable Setup Menu Custom Color)
Set to 1 to enable custom color settings for the
Setup menu. Set to 0 to disable custom color
settings for the Setup menu.
55-I. FOR. SETUP M. (Setup Menu Foreground Color)
Set according to Color Chart.
0 = Black 3 = Yellow 6 = Cyan
1 = Red 4 = Blue 7 = White
2 = Green 5 = Violet
41-I. AUTO COMPORT
Set to 1 to automatically switch to Comport when
equipment is connected to front computer input.
Set to 0 to disable front computer automatic
source selection.
56-I. BCK. SETUP M. (Setup Menu Background Color)
Set according to Color Chart.
0 = Black 3 = Yellow 6 = Cyan
1 = Red 4 = Blue 7 = White
2 = Green 5 = Violet
42-I. NOT USED
57-I. EN. AUDIO. COL. (Enable Audio Menu Custom Color)
43-I. NOT USED
44-I. NOT USED
3828VD0171G 2-3 DIGITAL FCS - INSTALLER MENU
Set to 1 to enable custom color settings for the
Audio menu. Set to 0 to disable custom color
settings for the Audio menu.
INSTALLER MENU
58-I. FOR. AUDIO. COL. (Audio Menu Foreground Color)
Set according to Color Chart.
0 = Black 3 = Yellow 6 = Cyan
1 = Red 4 = Blue 7 = White
2 = Green 5 = Violet
59-I. BCK. AUDIO. COL. (Audio Menu Background Color)
Set according to Color Chart.
0 = Black 3 = Yellow 6 = Cyan
1 = Red 4 = Blue 7 = White
2 = Green 5 = Violet
60-I. EN. VIDEO. COL. (Enable Video Menu Custom Color)
Set to 1 to enable custom color settings for the
Video menu. Set to 0 to disable custom color
settings for the Video menu.
61-I. FOR. VIDEO M. (Video Menu Foreground Color)
Set according to Color Chart.
0 = Black 3 = Yellow 6 = Cyan
1 = Red 4 = Blue 7 = White
2 = Green 5 = Violet
62-I. BCK. VIDEO. COL. (Video Menu Background Color)
Set according to Color Chart.
0 = Black 3 = Yellow 6 = Cyan
1 = Red 4 = Blue 7 = White
2 = Green 5 = Violet
68-I. BCK. SRC. M. (Source Menu Background Color)
Set according to Color Chart.
0 = Black 3 = Yellow 6 = Cyan
1 = Red 4 = Blue 7 = White
2 = Green 5 = Violet.
69-I. EN. CH-T COL (Enable Channel-Time Custom Color)
Set to 1 to enable custom color for the ChannelTime display. Set to 0 to disable custom color
for the Channel-Time display.
70-I. FOR. CH-T COL (Channel-Time Display Foreground Color) Set according to Color Chart.
0 = Black 3 = Yellow 6 = Cyan
1 = Red 4 = Blue 7 = White
2 = Green 5 = Violet
Note: If foreground and background color are
the same, menu background is transparent.
71-I. BCK. CH-T COL (Channel-Time Background Color)
Set according to Color Chart.
0 = Black 3 = Yellow 6 = Cyan
1 = Red 4 = Blue 7 = White
2 = Green 5 = Violet
Note: If foreground and background color are
the same, menu background is transparent.
72-I. NOT USED
63-I. EN. PTL. COL. (Enable Parental Menu Custom Color)
Set to 1 to enable custom color settings for the
V-Chip menu. Set to 0 to disable custom color
settings for the V-Chip menu.
64-I. FOR. PTL. M. (V-Chip Menu Foreground Color)
Set according to Color Chart.
0 = Black 3 = Yellow 6 = Cyan
1 = Red 4 = Blue 7 = White
2 = Green 5 = Violet
73-I. CH NOT AVBLE (Channel Not Available)
If set to 1 and channel override is set to 0,
“NOT AVAILABLE” message is displayed when direct accessing a channel not in the favorite
channel list.
74-I. CH-TIME SIZE (Channel-Time Size)
If set to 1 and transparent background is selected for Channel- Time display, (foreground
color = background color and custom color enabled) a large channel number is displayed instead of the normal Channel-Time display.
65-I. BCK. PTL. M. (V-Chip Menu Background Color)
Set according to Color Chart.
0 = Black 3 = Yellow 6 = Cyan
1 = Red 4 = Blue 7 = White
2 = Green 5 = Violet
66-I. EN. SRC. COL. (Enable Source Menu Custom Color)
Set to 1 to enable custom color for the Source
menu.
Set to 0 to disable custom color for the Source
menu.
67-I. FOR. SRC. M. (Source Menu Foreground Color)
Set according to Color Chart.
0 = Black 3 = Yellow 6 = Cyan
1 = Red 4 = Blue 7 = White
2 = Green 5 = Violet
75-I. NOT USED
76-I. DEFEAT XDS
Set to 1 to disable XDS display. Even if provided by broadcaster, XDS display will not appear. Set to 0 to enable XDS display. If provided by broadcaster, XDS display will appear
after new channel selection.
77-I. NOT USED
78-I. UPN MSB
User programmable number, most significant byte
readable by M.P.I. command. (Line - Day)
79-I. UPN MSB-1
User programmable number, most significant byte1 readable by M.P.I. command. (Week)
3828VD0171G 2-4 DIGITAL FCS - INSTALLER MENU
INSTALLER MENU
80-I. UPN MSB-2
User programmable number, most significant byte2 readable by M.P.I. command. (SN-HIGH)
81-I. UPN LSB
User programmable number, least significant byte
readable by M.P.I. command. (SN-LOW)
82-I. CHKSM ERROR
Enforces rigid M.P.I checksum validation.
Set to 1 for validation.
Set to 0 to turn off.
83-I. HANDSHK TIME (Handshake Time)
Adds an additional delay to the handshake time
which is 64 msec, thus relaxing M.P.I. timing
requirements to be compatible with PC based Windows controlled systems, range is 0 - 5.
Set to 0 to retain standard 64 msec delay. Set
to 1 - 5 to increase @ 16 msec ea., the delay up
to 144 msec.
84-I. PERMANENT BLK (Permanent Block)
Allows Parental Control blocking schemes to be
permanent by removing the blocking hours function.
Set to 1 to install Parental Control blocking
restrictions permanently. Set to 0 for userspecified hours control of blocking schemes.
85-I. A. MUTE TIME (Audio Mute Time)
Controls audio muting delay time when switching
between AUX sources. Range is 0 to 254 msec.
86-I. V. MUTE TIME (Video Mute Time)
Controls video muting delay time when switching
between AUX sources. Range is 0 to 254 msec.
87-I. NOT USED
88-I. EN NOISE MUTE (Enable Noise Mute)
Enables soft mute when a signal is not present.
89-I. POKE ENABLE
Enables poke function through M.P.I. commands.
90-I. NOT USED
91-I. NOT USED
92-I. NOT USED
93-I. NOT USED
94-I. NOT USED
95-I. NOT USED
97-I. NOT USED
98-I. NOT USED
99-I. NOT USED
100-I. NOT USED
101-I. NOT USED
102-I. NOT USED
103-I. NOT USED
104-I. NOT USED
105-I. NOT USED
106-I. A RATIO LOCK (Aspect Ratio Lock)
If set to 1, current picture aspect ratio is
retained at power Off. At power On, previous
aspect ratio will be used. If set to 0, resets
aspect ratio to default setting at TV turn On.
FACTORY MENU
ACCESSING THE FACTORY’S MENU
Using the remote control or the keyboard on the
front panel can access the Factory’s Menu items.
With the remote, just press and hold MENU (about
8 seconds) until the display changes, then press
1, 9, 3, 7, then ENTER. To exit the Factory’s
Menu, press ENTER again. Any changes you make
will be stored in nonvolatile memory. To access
the Factory Menu with the set’s keyboard press
and hold the MENU key until the Ch/Time display
appears, simultaneously press the ADJUST RIGHT
& CHANNEL UP keys.
USING THE FACTORY MENU
The Factory Menu has two pages, the Factory Menu
1 and the Factory Menu 2. The Factory Menu 1 is
to control or modify the main characteristics
of the CV RF, CV base band and Y/C signals. The
Factory Menu 2 is to control or modify the main
characteristics of the NTSC YUV and RGB Computer input signals. Their numbers, descriptions, ranges, factory default settings, and a
place for listing any changes made onsite are
given below and on the following pages.
The Factory’s menu opens with item 003-F VERT
POS item. Use the SELECT key to sequence through
the available menu items, or access an item
directly by entering the item number, and then
pressing MENU. For example, to access the item
015-F, press 1, 5, then MENU. To change the
settings use the Left/Right ADJ keys.
96-I. NOT USED
3828VD0171G 2-5 DIGITAL FCS - INSTALLER MENU
FACTORY MENU
DETAILED DESCRIPTIONS OF FACTORY MENU
ITEMS
000-F FACT MENU: Use the Select key to select
item #00, which is the first item in the Factory’s
Menu. The Factory Mode item should always be
left off (Zero is off). When The Factory Mode is
on, the Factory Menu line appears at the top of
the screen to allow for proper setting of the
video.
When the Factory Mode is turned off, all TV
functions are returned to normal. The dashes on
the menus are removed indicating that the Factory Mode is off. There are 4 ways to turn off
the Factory Mode:
1. Change Factory’s Menu Item “00 F Mode” to 0.
2. Run Auto Program.
3. Use the Clock Set feature to set the time.
4. Use Factory off IR code.
Notes:
• When the Factory Mode is on, the TV set will
automatically turn on when AC power is applied.
The POWER key will not turn the set off. The
only way to turn off the set is by removing the
AC power.
• Settings Displayed in Customer Menus: When
adjusting a bar graph setting in the Video and
Audio Menus, a number is displayed showing the
actual numeric value stored in EEPROM for that
setting. On menu items without a bar graph setting, two dashes indicate that the Factory Mode
is on. • Video Preference Settings Inhibited: In
the Video Menu, the Custom Video Preference settings are inhibited while the Factory Mode is on
and will NOT be stored in EEPROM. (This allows
the factory to temporarily change the settings
and not store them permanently.)
001-F PRESET PX: Used to store the customer
menu adjustments in the nonvolatile memory of
the EAROM. Settings for Contrast, Brightness,
Color and Tint are stored in this manner. 0 is
Custom and 1 is Preset.
002-F PRESET AX: Saves your custom audio set-
tings (Bass, table, balance, audio mode,
soundrite, front surr, speaker) in nonvolatile
memory (not affected by power loss). Memory status is indicated by a 1 for “custom settings
already stored”, or 0 for “custom settings have
not been stored.”
003-F VERT POS: Moves Captions and displays
vertically on the screen. Use the ADJUST keys.
004-F HORZ POS: Moves Captions and displays
horizontally on the screen. Use the ADJUST keys.
G2 ADJUSTMENT.
005-F AIR AFT: Enable/Disable (1/0). This fea-
ture is for enable or disable the AFT execution
in AIR Band.
006-F G2 ADJUST: Max value of 254d and default
value of 127d. It is required to adjust the
cutoff level when the horizontal line becomes
visible at center of screen during G2 adjustment.
007-F RF SUB_BRIGHT: Max value of 63d and de-
fault value of 31d for NTSC video format Depends
of factory adjustment.
008-F RF WHITE ADJ: Max value of 63d and de-
fault value of 25d for 27" and 28d for 32". It is
required as test condition to reduce the contrast level during RF sub brightness adjustment.
009-F RF BLACK ADJ: Max value of 63d and de-
fault value of 63d for 27" and 60d for 32". It is
required as test condition to increase the black
level during the RF sub brightness adjustment.
AUDIO OPTIONS
010-F VOL CLIPPING: Reduce clipping effects
due the gain combination of volume, bass and
treble settings. Range: 0-3. Fixed value = 0
(Reduce volume when gain combination > 12dB).
011-F SPAT STRENGHT: Spatial effect strength.
Fixed value = 63 (enlargement = 50%).
012-F SPAT MODE: Define the spatial effect mode.
Fixed value = 0 (Stereo Base width Enlargement
and Pseudo Stereo Effect).
013-F SPAT GAIN: Spatial effect high-pass gains.
Fixed value = 2 (2/3 high-pass gain).
014-F PRE AUX_INPUT: Defines the input gain
value for auxiliary input signals. Fixed value =
25 (0 dB gain).
015-F PRE AUD_DEMOD: Defines the input prescale
gain for the demodulated audio signal. Fixed
value = 24.
016-F AVC: Automatic volume correction decay
time. Fixed value = 4.
NTSC: IC CXA2150
017-F SUBCONT Sub contrast adjustment. Range:
0- 15, 0 = Minimum, 15 = Maximum. Contrast gain
control (Y system level adjustment). Range: 015, 0H = -1.9 dB, 7H = 0 dB, FH = +1.7 dB.
018-F SUBBRIGHT Sub-brightness control. Range
0- 63, settings for output DC bias out RGB OUT.
OH=-13IRE, 1Fh=CENTER, 3Fh=+13IRE.
019-F RDRIVE R channel drive gain control. Range:
0- 63, 0H = -4.2 dB, 29H = 0 dB, 3FH = +2.1 dB.
Fixed value.
3828VD0171G 2-6 DIGITAL FCS - FACTORY MENU
FACTORY MENU
020-F GDRIVE G channel drive gain control. Range:
0- 63, 0H = -4.2 dB, 29H = 0 dB, 3FH = +2.1 dB.
Fixed value.
021-F BDRIVE B channel drive gain control. Range:
0- 63, 0H = -4.2 dB, 29H = 0 dB, 3FH = +2.1 dB.
Fixed value.
022-F RCUTOFF R channel cutoff control Range:
0-63, 0H = -9.1dB, 1FH = 0 dB, 3FH = +4.4 dB.
Fixed value.
023-F GCUTOFF G channel cutoff control Range:
0-63, 0H = -9.1dB, 1FH = 0 dB, 3FH = +4.4 dB.
Fixed value.
024-F BCUTOFF B channel cutoff control Range:
0-63, 0H = -9.1dB, 1FH = 0 dB, 3FH = +4.4 dB.
Fixed value.
025-F BLKBTM RGB-OUT bottom limiter level con-
trol (valid when BLKSW = 1). The limiter level
is replaced with the reference DC for each H in
RGB system, and the drop voltage from that DC
defines it; it is not dependent on DC level
control setting made by BRIGHT, etc. This limiter functions for all video signals. For further details, refer to the description of operation. Range: 0-3.
026-F PICTURE: Picture gain control. Range:
0-63.
027-F BRIGHTNESS: Brightness level range: 0-
63.
028-F GAMMA Control of gamma correction amount.
0H = OFF. 3H = MAX.
029-F DCOL: Dynamic color mode setting. Range:
0 = OFF, 1 = ON, R:98%, G:100%, B:102.5%.
037-F LTIMODE AUX: Luminance transient improvement for aux video inputs. Default value
in 1.
038-F SYSTEM AUX:
ing; select the band in accordance with the TV
System. Range: 0- 3, 0 = NORMAL, 1 = FF, 2 = HD,
3 = FIX-HD (setting which gives greater importance to frequency response than 2).
Signal frequency band switch-
039-F DCTRAN: Y system DC transmission ratio
setting. Range: 0-3, 2 = 90%.
040-F YOFFSET: DC offset canceling for y sig-
nal. Default value is 7.
041-F DPICLEV: Dynamic picture (black expan-
sion) control. Range: 0-3, 0 = OFF, 1 = Low:
inflection point 25 IRE, 2 = Medium: inflection
point 30 IRE, 3 = High: inflection point 35 IRE.
042-F LRGB2LEV: LRGB2 system picture level con-
trol. Range: 0-15, 0H = -8 dB, Fh = 0 dB.
043-F ABLMODE: Switch for ABL mode. Range: 0-3,
0 = Picture ABL only mode, 1 = Picture/brightness ABL mode: Low, 2 = Picture/brightness ABL
mode: Medium, 3 = Picture/brightness ABL mode:
High.
044-F ABLTH: Adjustment of threshold voltage
for ABLIN (Pin 44) input. Range 0-15. Default
value is 2.
045-F PABL: RGB output level detection DC set-
ting for peak ABL. Default value is 15d.
046-F CBOFFSET: For canceling the offset be-
tween CrCb of IN1 and SELIN systems. Range: 0-
63. This variable range is DC variation amount
of respective input pins.
030-F PLIMITLEV: Setting of level detection DC
at RGBOUT of PEAK-ABL. 0 = 115IRE.
031-F WBSW: White balance offset setting. 0=off,
normal color temperature.
047-F CROFFSET: For canceling the offset be-
tween CrCb of IN1 and SELIN systems. Range: 0-
63. This variable range is DC variation amount
of respective input pins.
048-F AKBTIM: AKB Blue channel reference pulse
032-F CTILEV AUX: Chrominance transient im-
provement for Aux video input.
timing setting. Default value is 18d.
049-F VMLEV: Not available.
033-F CTIMODE AUX: Chrominance transient mode
for Aux video input.
050-F CDOFF: Sharpness CD ON/OFF. Default value
is 1 (off).
034-F COLAXIS: Color detection axis setting. 0=
for NTSC.
035-F GAMMAL: Fine tuning for gamma.
036-F LTILEV AUX: Luminance signal edge en-
hancement setting for Aux video inputs. Range:
0-3, 0 = OFF, 1 = Low, 2 = Medium, 3 = High.
3828VD0171G 2-7 DIGITAL FCS - FACTORY MENU
051-F SHPCD: Sharpness gain control in part of
high color saturation when Cr input signal is
100% Default value is 3.
052-F VM-COR: Not available.
053-F VMF0: Not available.
FACTORY MENU
054-F SHPF0: Sharpness fo setting. 3= 3Mhz @
Normal mode
055-F BLKOFF: Blanking ON/OFF SW when AKBOFF=1
Default value is 0.
056-F CLPPHASE: Internal clamp phase pulse con-
trol. Default value is 0 (+5%).
057-F CLPSHIFT: Internal clamp pulse start phase
setting 1= Clamp phase setting –3.125%
058-F CLPGATE: Switch for gating internal clamp
pulse with input Hsync. 1=gated with inHsync.
059-F LEFTBLK
060-F RIGHTBLK
061-F HBLKSW:
ware full display mode on a 16:9 CRT. Default
value is 1.
HBLK control enable for 4:3 soft-
062-F SABL: S-ABL gain setting. 3=S-ABL gain
max.
063-F SHPF1: High fo sharpness gain control.
Default value is 2.
064-F PREOVER Sharpness preshoot/overshoot ra-
tio setting. Range: 0-3, 0 = 1:1.5 (pre:over), 3
= 2:1 (pre:over). Default value is 0.
076-F V_LIN: Vertical linearity adjustment.
Range: 0- 15, Initial value: 07.
077-F V_S_CORRECTION: Vertical S correction.
Range: 0-15, Initial value: 5.
078-F UP_VLIN: Vertical linearity control. Range:
0- 15, Initial value: 0.
079-F LO_VLIN: Vertical linearity control. Range:
0- 15, Initial value: 0.
080-F H_SIZE: Horizontal amplitude adjustment.
Range: 0-63, Initial value: 43.
081-F H_POSITION: Horizontal position adjust-
ment. Range: 0-63, Initial value: 31.
082-F PIN_PHASE: Horizontal trapezoidal adjust-
ment. Range: 0-63, Initial value: 31.
083-F PIN_AMP: Pincushion adjustment. Range:
0-63, Initial value: 31.
084-F UP_CPIN: Horizontal pin adjustment for
top edge. Range: 0-63, Initial value: 38.
085-F LO_CPIN: Horizontal pin adjustment for
bottom edge. Range: 0-63, Initial value: 34.
086-F UP_UCP: Horizontal pin adjustment for ex-
treme top edge. Range: 0-3, Initial value: 0.
065-F VMLMT:
066-F VMDLY:
067-F AKBOFF:
068-F UPBLK
069-F LOBLK
070-F AFC_BOW:
Range: 0-63, Initial value: 31.
Vertical line bow adjustment.
071-F AFC_ANGLE: Vertical line slope adjust-
ment. Range: 0-63, Initial value: 31.
072-F V_ASPECT: Aspect control ratio. Range:
0-63, Fixed Value: 47 for 4:3 CRT.
073-F V_SIZE: Vertical amplitude adjustment.
Range: 0-63, Initial value: 50.
074-F V_POSITION: Vertical position adjustment.
Range: 0-63, Initial value: 31.
075-F V_SCROLL: Vertical picture scroll con-
trol. Range: 0-63, Initial value: 28.
087-F LO_UCP: Horizontal pin adjustment for ex-
treme bottom edge. Range: 0-3, Initial value: 0.
088-F UP_UCG: Horizontal pin gain adjustment
for extreme top edge. Range: 0-3, Initial value:
0.
089-F LO_UCG: Horizontal pin gain adjustment
for extreme bottom edge. Range: 0-3, Initial
value: 0.
090-F UC_POL: Horizontal pin polarity setting
for extreme top & bottom edge. Range: 0-1, Initial value: 0.
091-F V_COMP: HV fluctuation compensation amount
setting for vertical picture size. Range: 0-15,
Initial value: 07.
092-F H_COMP: HV fluctuation compensation amount
setting for horizontal picture size.
Range: 0-15, Initial value: 07.
093-F PIN_COMP: HV fluctuation compensation
amount setting for horizontal pin distortion.
Range: 0-7, Initial value: 0.
3828VD0171G 2-8 DIGITAL FCS- FACTORY MENU
FACTORY MENU
094-F AFC_COMP: HV fluctuation compensation
amount setting for H position. Range: 0-7, Initial value: 0.
095-F APC-MODE
096-F SYNC-PHASE
097-F RST-SW
NTSC: IC CXA2151
098-F HSMASK: Sets whether or not to add HSYNC
within VSYNC at SELHOUT. 1= Do not add HSYNC.
099-F VTC: Sets the vertical sync separation
time constant. 3=13us.
100-F HWIDTH: Sets the SELH OUT output pulse
width. 2=1.7us.
101-F HFREQ: Select the frequency of the dummy
sync output to SELHOUT. 1=31.25Khz.
NTSC: IC VSP9405
102-F HPOLM: Horizontal polarity in HINP. De-
fault value is 2 (Auto detect polarity).
103-F COMBUSEM: Comb filter usage CD1.
115-F HUEM: Tint control for NTSC signals.
116-F AGCMDM: AGC behavior can be chosen from
four possible modes.
117-F AGCADJ1M: Automatic gain adjustment ADC1.
118-F CLMPST1SM: Measure pulse duration for ADC1
119-F CLMPHIGHM: Vertical end of clamping pulse.
Default value is 255 (Line 766).
120-F CLMPLOWM: Vertical start of clamping pulse.
Default value is 3 (Line 6)
121-F VDETIFSM: Vertical sync detection slop,
0=Normal, 1=slow. Default value in 1.
122-F CLMPD1SM: Clamping pulse duration for ADC1
123-F ISHFTM: Adjustment for horizontal PLL.
124-F NOTCHOFFM: Luminance notch filter 0=en-
abled and 1=bypassed 053-F TNOTCHOFFM: Default
value is 0.
125-F TNOTCHOFFM: Luminance notch-filter.
126-F NTCHSELM: Luminance notch selection. 3=broad
notch.
104-F CRCBM: Choice of UV or Cb Cr output.
2=modified Cr Cb color space.
105-F YCSELM: Y/C select among composite video
and s-video inputs.
106-F NOSIGBM: No signal behavior. 0=noisy screen
when out of sync.
107-F CLMPST1M: Measure pulse start for ADC1.
108-F CHRFM: Select Chroma bandwidth.
109-F PLLTCM: Time constant HPLL (VCR...TV) De-
fault value in 0 (very fast).
110-F COMBM: Delay line. 1=Do not use delay
line.
111-F CKILLM: Chroma level for Color off.
112-F YCDELM AUX: The between Y and C is well
aligned and can also be adjusted in steps of 50
ns for Aux video inputs.
113-F NSREDM: Fine-tuning of the PLL time con-
stant can be done.
127-F TRAPBLUM: Notch frequency for 4.250Mhz.
0=4.25Mhz.
128-F TRAPREDM: Notch frequency for 4.406Mhz.
0=4.406Mhz, 057-F COMBUSEM: Default value is 2
129-F PIXPLINM: Pixels per line slave channel.
0=defined by DISPMODE Y Pr Pb IC VSP9405.
130-F WRPOSXM: Horizontal position of master pic-
ture in the memory. 0=left border position.
131-F WRPOSYM: Vertical position of master pic-
ture in the memory. 0=Upper border position.
132-F FMSYN: Synchronization of film mode sig-
nal. 0=no delay.
133-F FMSYNUNS: Synchronization of film mode sig-
nal. 0=no delay.
134-F YUVMAT: YUV color matriz. 0= Y Cr Cb.
135-F TINT: Tint control for YUV input.
136-F RDPOSXM_L: Horizontal read position mas-
ter.
114-F LPCDELM: Window shift for fine error cal-
culation. Default value in 0 (no offset).
3828VD0171G 2-9 DIGITAL FCS - FACTORY MENU
137-F RDPOSXM_H: Default value is 0.
FACTORY MENU
138-F READM: Read mode master channel. 0=Read-
ings A and B fields.
139-F RDPOSYM: Vertical read position.
140-F RSHIFTM: Raster shift master. 1=Enable.
141-F NRONM: Temporal noise reduction. 1= En-
abled.
142-F TNRNR4YM: Temporal noise reduction for
Luma. 1= Enabled.
143-F TNRMD4YM: Motion detection of temporal
noise reduction for Luma. 0=Frame based.
144-F TNRNR4CM: Motion detection of temporal
noise reduction for Chroma. 0=Frame based.
145-F TNRCLYM: TNR luminance classification.
146-F TNRCLCM: TNR chrominance classification.
147-F VAAPRESCM: Vertical low pass filter (pre-
scaler) 0=Disabled.
148-F VPKPRESCM: Vertical peaking. 15= Verti-
cal peaking has no effect.
161-F VERWIDTHM_H: Default value is 1.
162-F VERWIDTHM_L: Vertical picture width. De-
fault value is 31.
163-F PKCTIBPM AUX: Band pass Peaking factor for
CTI of Aux video inputs. Default value is 3.
164-F PKCTIHPM AUX: High pass Peaking factor for
CTI of Aux video inputs. Default value is 2.
165-F LTIM: Luminance transient improvements.
0=disabled.
166-F APK1BPM: 1
pass part). Default value is 0.
167-F APK2BPM: 2
pass part). Default value is 4.
st
adaptive peaking factor (band
nd
adaptive peaking factor (band
168-F ATH1BPM: Peaking denoising threshold (band
pass part). 0=off.
169-F ATH2BPM: 2
part). 0=0.
nd
Peaking threshold (band pass
170-F THEM: Turning point threshold. Default value
is 3.
149-F VCRPRESCM: Shift of chrominance signal.
0=No shift.
150-F NALPFIPM: No active lines per field in-
put.
151-F VPREBYPM: Vertical pre-scaler by pass.
0=enabled.
152-F DPBRT: Brightness level range from 0 to
63. Default is 3.
153-F DPCON: Contrast level range from 0 to 63.
Default is 30.
154-F DPCNS: Contrast noise shaper. 0=disabled.
155-F HORPOSM_H: Default value is 0.
156-F HORPOSM_L: Horizontal position inside ac-
tive picture area. Default value is 325.
157-F VERPOSM_H: Default value is 0.
158-F VERPOSM_L: Vertical position inside ac-
tive picture area. Default value is 16.
171-F APK1HPM_10: 1
(high pass part). Default value is 0.
172-F APK2HPM: 2
pass part). Default value is 3.
st
adaptive peaking factor
nd
adaptive peaking factor (high
173-F ATH1HPM: Peaking denoising threshold (high
pass part). 0=off.
174-F ATH2HPM: 2
part). 0=0.
175-F APK1BPM_32: 1
(band pass part). Default value is 0.
176-F APK1HPM_32: 1
(high pass part). Default value is 0.
nd
Peaking threshold (high pass
st
adaptive peaking factor
st
adaptive peaking factor
177-F CORONM: Coring or denoising for low ampli-
tudes. Default value is 0 (coring off, denoising
on).
178-F DCIONM: Digital contrast improvements. 1=en-
abled.
179-F AB_FTCM: Filter time constant for bright-
ness average. Default value is 0.
159-F HORWIDTHM_H: Default value is 3.
180-F PK_FTCM: Filter time constant for frame
peak value. Default value is 0.
160-F HORWIDTHM_L: Horizontal picture width.
Default value is 32.
3828VD0171G 2-10 DIGITAL FCS- FACTORY MENU
FACTORY MENU
181-F GCMON: Progressive picture improvement.
0=off.
182-F HSPPL: H sync shift. Default value is 0
183-F VSLPF: V sync shift. Default value is 0
184-F CVSEL1: Output select for CVBS2.
185-F CVSEL2: Output select for CVBS4 or Y.
186-F CLMPSIG1: Clamping signals ADC1. 0=1
decoder.
st
color
187-F YCTOCOMB: YC to Comb filter. 0=Normal op-
eration.
188-F VDG: Vertical difference gain. 1=medium2
189-F HDG: Horizontal difference gain. 2=medium2
190-F DDR: Diagonal dot reduction. 1=medium1
191-F COR: Vertical peaking coring. 0=disabled
192-F NOSEL: Notch filter select. 3=max peaked.
205-F VOUTPOL: Vertical output polarity. 0=high
active.
206-F BLANPOL: Blank polarity. 0=high active.
207-F VBLANDEL_95: Vertical delay in lines from
in v sync. Default value is 0.
208-F BLANLEN_H: Default value is 0.
209-F BLANLEN_L: Default value is 0.
210-F VBLANDEL_40: Vertical length in lines from
start of active blank signal. Default value is 0.
211-F VBLANLEN_H: Vertical length in lines from
start of active blank signal. Default value is 0.
212-F VBLANLEN_L: Vertical length in lines from
start of active blank signal. Default value is 0.
213-F PKLY: Voltage level for Y DAC output. De-
fault value is 237d.
214-F PKLU: Voltage level for U DAC output. De-
fault value is 254d.
193-F DCR: Vertical peakigDC rejection filter.
0=disabled.
194-F VPK: Vertical peaking gain. 0= NO VPK.
195-F LINLENH60: Number of pixels for 60HZ. De-
fault value is 3.
196-F DISCOMB: Disable comb filter. Depending
video source selected.
197-F HWID: Minimum width of H sync. Default
value is 0.
198-F FION: Increment freeze before V sync. 0= no
freeze.
199-F PPLIP_H: Default value is 2.
200-F PPLIP_L: P
ixel per line. Default value is 0.
201-F TO1RGB: YUV output selection. Default value
is 0.
202-F BLANDEL: Delay in pixels from h sync. De-
fault value is 0 (no delay).
203-F VBLANPOL: Vertical blanking signal polar-
ity. 0= positive.
204-F HOUTPOL: Horizontal output polarity. 0=
high active.
215-F COARSEDEL: Luminance coarse delay output.
Default value is 5d.
216-F FINEDEL: Luminance fine delay output. De-
fault value is 0.
217-F PKLV: Voltage level for V DAC output. De-
fault value is 254d.
218-F MDVFON: Default value is 1.
219-F FM-RES: Default values is 0.
220-F FM-THYON: Default value is 0.
221-F FM-THRON: Default value is 1.
222-F FMATH: Default value is 0.
223-F FMDTH: Default value is 15.
TDA4887 NTSC
224-F RGAIN CTRL NTSC: Red gain control is used
for white point adjustment. Range: 0-255d.
225-F GGAIN CTRL NTSC: Green gain control is
used for white point adjustment. Range:0-255d.
226-F BGAIN CTRL NTSC: Blue gain control is used
for white point adjustment. Range: 0-255d.
3828VD0171G 2-11 DIGITAL FCS - FACTORY MENU
FACTORY MENU
227-F R-CUTOFF NTSC: Red cutoff control is used
to adjust cut-off voltage at the cathode. Range:
0-255d.
228-F G-CUTOFF NTSC: Green cutoff control is
used to adjust cut-off voltage at the cathode.
Range: 0-255d.
229-F B-CUTOFF NTSC: Blue cutoff control is used
to adjust cut-off voltage at the cathode. Range:
0-255d.
230-F OSD CONT NTSC: OSD amplitude can be con-
trolled by OSD contrast with a range of 12dB.
Default value is 7d.
231-F AC BLK LEV NTSC: Black level for AC cou-
pling with 3bit DAC. Default value is 0.
232-F BRI NTSC: Default value is 0 (internal
brightness control with grey scale tracking).
233-F DISV NTSC: RGB Video signal on/off. De-
fault value is 0 (enabled).
234-F FPOL NTSC: Default value is 0 (Negative
feedback polarity selected, No external DAC voltage outputs).
006-F MAX COLOR: Max value of 63d and default
value of 55d for 27" and 47d for 32". This value
is used in one formula to limit the maximum color
level.
007-F RF SUB_TINT: Max value of 15d and default
value of 7d. This value is used in one formula to
center the tint level of RF input.
008-F AUX SUB_TINT: Max value of 15d and default
value of 7d. This value is used in one formula to
center the tint level of composite video inputs.
009-F YC SUB_TINT: Max value of 15d and default
value of 7d. This value is used in one formula to
center the tint level of S-Video inputs WHITE
BALANCE RESET.
010-F NTSC CUT: Max value of 254d and default
value of 127d. This register is used in one formula to reset the red, green and blue cutoff
values of RF, Composite video and S-Video inputs
before G2 setup and white balance adjustment.
011-F NTSC GAIN: Max value of 254d and default
value of 127d. This register is used in one formula to reset the red, green and blue gain values
of RF, Composite video and S-Video inputs before
G2 setup and white balance adjustment.
235-F DEPTH_PB NTSC: Produces an ultra black
level during blanking and output clamping which
is the most negative signal at the signal output
pins. Default value is 1.
236-F APCONSVGA
FACTORY MENU 2
NTSC VIDEO ADJUST
001-F AUX OFFSET: Black level settings for com-
posite video and S-Video inputs. Depends of RF
sub brightness adjustment. Max value of 64d and
default value of 32d.
002-F YUV OFFSET: Black level setting for Y Pr
Pb input. Depends of RF sub brightness adjustment. Max value of 64d and default value of 32d.
003-F MAX CONTRAST: Max value of 64d and default
value of 40d for 27"and 33d for 32" for NTSC video
format. This value is used in one formula to
limit the max contrast level.
004-F MAX BRIGHT: Max value of 64d and default
value of 55d for 27" and 64d for 32". This value
is used in one formula to limit the max brightness level.
012-F SVGA CUT OFFSET: Max value of 254d and
default value of 127d. . This register is used in
one formula to reset the red, green and blue
cutoff values of SVGA inputs before G2 setup and
white balance adjustment.
013-F SVGA GAIN OFFSET: Max value of 254d and
default value of 127d. This register is used in
one formula to reset the red, green and blue gain
values of SVGA input before G2 setup and white
balance adjustment.
014-F YPrPb CUT OFFSET: Max value of 254d and
default value of 127d. . This register is used in
one formula to reset the red, green and blue
cutoff values of Component inputs before G2 setup
and white balance adjustment.
015-F Y PrPb GAIN OFFSET: Max value of 254d and
default value of 127d. This register is used in
one formula to reset the red, green and blue gain
values of component inputs before G2 setup and
white balance adjustment.
DEFLECTION OFFSETS
016-F H_SIZE OFFSET
017-F H_POSITION OFFSET
018-F V_SIZE OFFSET
005-F SUB COLOR: Max value of 63d and default
value of 32d.This value is used in one formula to
limit the minimum color level.
3828VD0171G 2-12 DIGITAL FCS - FACTORY MENU
019-F V_SCROLL OFFSET
FACTORY MENU
020-F PIN_AMP OFFSET
021-F UP_CPIN OFFSET
022-F LO_CPIN OFFSET
SVGA
023-F UP-BLK
024-F LO-BLK
025-F AFC_BOW:
0-63, Initial value: 31.
026-F AFC_ANGLE: Vertical line slope adjustment.
Range: 0-63, Initial value: 31.
Vertical line bow adjustment. Range:
027-F V_ASPECT: Aspect control ratio. Range: 0-
63, Fixed Value: 47 for 4:3 CRT.
028-F V_SIZE: Vertical amplitude adjustment.
Range: 0-63, Initial value: 50.
029-F V_POSITION: Vertical position adjustment.
Range: 0-63, Initial value: 31.
030-F V_SCROLL: Vertical picture scroll control.
Range: 0-63, Initial value: 28.
031-F V_LIN: Vertical linearity adjustment. Range:
0- 15, Initial value: 07.
032-F V_S_CORRECTION: Vertical S correction.
Range: 0-15, Initial value: 5.
041-F UP_UCP: Horizontal pin adjustment for ex-
treme top edge. Range: 0-3, Initial value: 0.
042-F LO_UCP: Horizontal pin adjustment for ex-
treme bottom edge. Range: 0-3, Initial value: 0.
043-F UP_UCG: Horizontal pin gain adjustment for
extreme top edge. Range: 0-3, Initial value: 0.
044-F LO_UCG:
extreme bottom edge. Range: 0-3, Initial value: 0.
Horizontal pin gain adjustment for
045-F UC_POL: Horizontal pin polarity setting
for extreme top & bottom edge. Range: 0-1, Initial value: 0.
046-F V_COMP: HV fluctuation compensation amount
setting for vertical picture size. Range: 0-15,
Initial value: 07.
047-F H_COMP: HV fluctuation compensation amount
setting for horizontal picture size. Range: 0-15,
Initial value: 07.
048-F PIN_COMP: HV fluctuation compensation amount
setting for horizontal pin distortion.Range: 0-7,
Initial value: 0.
049-F AFC_COMP:
setting for H position. Range: 0-7, Initial value: 0.
HV fluctuation compensation amount
050-F RGAIN OFFSET
051-F GGAIN OFFSET
052-F BGAIN OFFSET
033-F UP_VLIN: Vertical linearity control. Range:
0- 15, Initial value: 0.
053-F R-CUT OFFSET
054-F G-CUT OFFSET
034-F LO_VLIN: Vertical linearity control. Range:
0- 15, Initial value: 0.
035-F H_SIZE: Horizontal amplitude adjustment.
Range: 0-63, Initial value: 43.
055-F B-CUT OFFSET
056-F SUBBRIGHT SVGA:
fault value of 31d for SVGA format. Depends on
factory adjustment of NTSC video format.
Max value of 64d and de-
036-F H_POSITION: Horizontal position adjust-
ment. Range: 0-63, Initial value: 31.
037-F PIN_PHASE: Horizontal trapezoidal adjust-
ment. Range: 0-63, Initial value: 31.
038-F PIN_AMP: Pincushion adjustment. Range: 0-
63, Initial value: 31.
039-F UP_CPIN: Horizontal pin adjustment for top
edge. Range: 0-63, Initial value: 38.
040-F LO_CPIN: Horizontal pin adjustment for bottom
edge. Range: 0-63, Initial value: 34.
3828VD0171G 2-13 DIGITAL FCS - FACTORY MENU
057-F MAXCONTRAST SVGA: Max value of 64d and
default value of 52d for 27"and 58d for 32"for
NTSC video format. This value is used in one
formula to limit the max contrast level on SVGA
format.
058-F MAXBRIGHT SVGA: Max value of 64d and de-
fault value of 35d for 27" and 54d for 32". This
value is used in one formula to limit the max
brightness level on SVGA format.
059-F OSD CONT SVGA: OSD amplitude can be con-
trolled by OSD contrast with a range of 12dB.
Default value is 7d.
FACTORY MENU
060-F AC BLK LEV SVGA: Black level for AC cou-
pling with 3bit DAC. Default value is 0.
061-F BRI SVGA: Default value is 1 (internal
brightness control without grey scale tracking).
062-F DEPTH PB SVGA: Produces an ultra black
level during blanking and output clamping which
is the most negative signal at the signal output
pins. Default value is 1.
063-F DISV SVGA: RGB Video signal on/off. De-
fault value is 0 (enabled).
064-F FPOL SVGA: Default value is 0 (Negative
feedback polarity selected, No external DAC voltage outputs).
Y Pr Pb: IC VSP9405.
065-F PWTHDM: Selection of white peak threshold.
Default value is 3.
066-F LMOFSTDM: Luminance offset in color de-
coder during visible picture. 0= No offset NTSC.
067-F VINPM: Vertical pulse detection. 0= from
sync signal
068-F HINPM: Synchronization input. 0= from CVBS
front end.
069-F BRTADJ: Brightness adjustment for Y Pr Pb.
Default value is 235d.
070-F CONADJ: Contrast adjustment for Y Pr Pb.
Default value is 42d.
071-F CHRSFR: Chroma sub-sampling filter.1=enabled
079-F USATADJ: U saturation adjustment. Default
value is 40d.
080-F VSATADJ: V saturation adjustment. Default
value is 42d.
081-F ADCSEL: Select ADC for sync signal conver-
sion. 0=Use ADC_G
082-F AABYP: Bypass RGB/YUV anti-aliasing fil-
ter. 0 = use filter
083-F CLMPVG: Clamping value G ADC. 1=80.
084-F DCLMPF: Clamping value fast blank input.
0= enabled.
085-F AGCADJR: Gain adjustment Red. Default value
is 32d.
086-F AGCADJB: Gain adjustment Blue. Default value
is 32d.
087-F MIXOP: Mixing configuration. Default value
is 1.
088-F CLMPRB: Clamping value Red and Blue ADC.
089-F AGCADJG: Gain adjustment Green. Default
value is 32d.
090-F AGCADJF: Gain adjustment fast blank. De-
fault value is 32d.
091-F RBOFST: Clamping correction for R/B ADC.
Default value is 4d.
092-F FBLOFFST: Fast blank offset correction.
Default value is 32d.
072-F AASEL: Digital anti-aliasing selection.0=-
3Db @ 10.6Mhz
073-F FBLDEL: Fast blanking delay vs RGB/YUV in-
put. 2= 100ns delay.
074-F GOFST: Clamping correction for G ADC. 2=64
G/Y with sync, pedestal offset visible.
075-F MIXGAIN: Gain of fast blanking signal. De-
fault value is 3.
076-F YFDEL: Y delay adjustment. Default value is
55d.
077-F UVDEL: UV delay adjustment. Default value
is 55d.
078-F RGBSEL: RGB input selection. 0= Use RGB/YUV
input1.
3828VD0171G 2-14 DIGITAL FCS - FACTORY MENU
093-F YUVSEL: YUV or RGB input selection. De-
fault values is 0 (YUV expected).
094-F OPDEL_MSB: Vertical delay for output op-
eration. Default value is 0.
095-F OPDEL: Vertical delay for output opera-
tion. Default value is 247d
Y Pr Pb: IC TDA4887
096-F RGAIN CTRL Y PrPb: Red gain control is
used for white point adjustment. Range: 0-255d.
097-F GGAIN CTRL Y PrPb: Green gain control is
used for white point adjustment. Range:0-255d.
098-F BGAIN CTRL Y PrPb: Blue gain control is
used for white point adjustment. Range: 0-255d.
FACTORY MENU
099-F R-CUTOFF Y PrPb: Red cutoff control is
used to adjust cut-off voltage at the cathode.
Range: 0-255d.
100-F G-CUTOFF Y PrPb: Green cutoff control is
used to adjust cut-off voltage at the cathode.
Range: 0-255d.
101-F B-CUTOFF Y PrPb: Blue cutoff control is
used to adjust cut-off voltage at the cathode.Range:
0-255d.
102-F OSD CONT Y PrPb: OSD amplitude can be
controlled by OSD contrast with a range of 12dB.
Default value is 7d.
103-F AC BLK LEV Y PrPb: Black level for AC
coupling with 3bit DAC. Default value is 0.
104-F BRI Y PrPb: Default value is 0 (internal
brightness control with grey scale tracking).
105-F DEPTH PB YUV: Produces an ultra black level
during blanking and output clamping which is the
most negative signal at the signal output pins.
Default value is 1.
106-F DISV Y PrPb: RGB Video signal on/off. De-
fault value is 0 (enabled).
107-F FPOL Y PrPb: Default value is 0 (Negative
feedback polarity selected, No external DAC voltage outputs.
NTSC: IC CXA2150
110-F LTILEV_YC: Luminance signal edge enhance-
ment setting for S-Video inputs. Range: 0-3, 0 =
OFF, 1 = Low, 2 = Medium (default value), 3 =
High.
111-F LTIMODE_YC: Luminance transient improve-
ment for S-Video inputs. Default value in 1 Y Pr
Pb: IC CXA2150
112-F CTILEV_RF: Chrominance transient improve-
ment for RF input. Default value is 3.
113-F CTIMODE_RF: Chrominance transient mode for
RF input. Default value is 1 NTSC: VSP9405.
114-F LTILEV_RF: Luminance signal edge enhance-
ment setting for RF input. Range: 0-3, 0 = OFF, 1
= Low, 2 = Medium, 3 = High.
115-F LTIMODE_RF: Luminance transient improve-
ment for RF input. Default value in 1.
116-F SYSTEM_RF: Signal frequency band switch-
ing; select the band in accordance with the TV
System. Range: 0- 3, 0 = NORMAL, 1 = FF, 2 = HD,
3 = FIX-HD (setting which gives greater importance to frequency response than 2).
117-F YCDELM_RF: The between Y and C is well
aligned and can also be adjusted in steps of 50 ns
for RF input. Default value is 31.
118-F PKCTIBPM_RF: Band pass Peaking factor for
CTI of RF input. Default value is 1.
108-F LTILEV_YPRPB: Luminance signal edge en-
hancement setting for Component video input. Range:
0-3, 0 = OFF, 1 = Low, 2 = Medium (default), 3 =
High.
109-F LTIMODE_YPRPB:
ment for component video input. Default value in 1.
Luminance transient improve-
119-F PKCTIHPM_RF: High pass Peaking factor for
CTI of RF input. Default value is 1.
3828VD0171G 2-15 DIGITAL FCS - FACTORY MENU
CIRCUIT OVERVIEW
BASIC CIRCUIT THEORY
POWER SUPPLY DEFINITION
The Power Supply uses a COLD chassis
and is a single sided circuit board
that has been developed for screen sizes
27" through 32". The power supply features two switch mode power regulators
for voltages sources. One is intended
for Standby sources and the other one
supplies the main switched voltages.
Both power supplies use direct regulation. One error amplifier and one
optocoupler are used for each power
supply. This chassis also is Energy
Star compliant for low power consumption in standby mode (less than 1 Watt
of consumption). This is the main reason for the standby power supply.
SWITCH MODE REGULATOR
This chassis has two switching power
supplies (quasi-resonant topology type).
The AC line is routed through the fuse
FX3400 (5A @ 250 V slow blow) and then
through the bridge rectifier circuit
BRX3400 and CX3406 for the switched
power supply and through the bridge
rectifier circuit BRX3410 and CX3414
for the stand-by power supply. The AC
operation range is between 90 Vrms to
135 Vrms. A filter consisting of LX3400,
CX3402 and CX3403 is employed before
the rectifier circuits to reduce noise
from the AC line and vice versa (EMI).
STAND-BY START UP
The voltage output of rectifier BRX3410
(+V2 150VDC) is applied to the standby
SMPS which consists of ICX3612, ICX3700,
ICX3701, and the standby chopper transformer TX3612.
When the PIN 5 of ICX3612 terminal voltage reaches 17.5 VDC (typical), the
control circuit enables regulator operation. Once the regulator output voltage is established, the drive winding
DX3601 starts to charge CX3605 via
DX3601. The voltage on CX3605 thus recovers to the nominal drive voltage.
SWITCHED POWER SUPPLY START UP
The voltage output of the rectifier
BRX3400 (+V1 150VDC) is supplied to
the Main Switch Mode Regulator Power
Supply (SMPS).
The Main SMPS consists of ICX3670,
ICX3750, and ICX3751. Its chopper transformer consists of TX3670.
When the PIN 4 of ICX3670 terminal voltage reaches 16 VDC (typical), the control circuit enables regulator operation. Once the regulator output voltage is established, the drive winding
DX3653 starts to charge CX3653 via
DX3653. The voltage on CX3653 thus recovers to the nominal drive voltage.
DEFLECTION AND HIGH VOLTAGE SECTION
The principal function of the Deflection and HV circuits is to supply horizontal and vertical currents to the
deflection yoke coils, and the high
voltage generation. They are designed
for use in a single frequency television. The new FCS converts the NTSC
horizontal scan 15.75KHz to 37.9 KHz
scan by means of a digital video processor.
This section can be divided into 5 functional blocks.
1. Horizontal Deflection and HV Generation
2. Base Drive
3. Pincushion Modulator Circuit
4. Shutdown Circuit
5. Vertical Deflection
Horizontal Deflection and HV Generation
The Horizontal Deflection circuitry is
a common flyback type used in many television and monitor applications. QX3204
is the Horizontal Output Transistor.
When QX3204 is initially turned on,
current is allowed to flow from the B+
supply, through TX3201 and QX3204. This
allows energy to be stored in TX3201.
3828VD0171G 3-1 DIGITAL FCS - CIRCUIT OVERVIEW
CIRCUIT OVERVIEW
When QX3204 is turned off some of this
energy is returned to charge the Scapacitor(s) CX3209, CX3208, and CX3210.
After several cycles (repeating at scanning frequency) sufficient voltage appears across the S-capacitor providing
an additional path producing current
flow though the horizontal deflection
yoke coil (connector CN3Y3). The Damper
Diodes DX3202 and DX3203 provide the
negative current path. The result is a
positive and negative saw tooth current through the horizontal deflection
coils (approximately 12 to 14 Amps.
peak to peak). When QX3204 is turned
off about 1300 Volts peak of flyback
voltage is produced from the stored
energy in the horizontal deflection
coils and TX3201. This voltage is induced to secondary windings of TX3201
to generate the high voltage, 30 KV.
The flyback (or retrace) period is about
5 uS.
A capacitive divider, CX3205 and CX3207,
provides a low voltage flyback pulse
(H-FBP) used for synchronization, phase
comparison, etc. This pulse is sent to
the main chassis via pin 3 of connector
CN1D2. Linearity Coil, L3200, is a saturating inductor skewed by a permanent
magnet bonded to the coil. It produces
a nonlinear inductance curve vs the
current. This characteristic cancels
non-linearities in the deflection current caused by horizontal deflection
coil resistance.
Base Drive
The base Drive circuit provides high
forward and reverse current to drive
the base of the Horizontal Output Transistor QX3204, from a low level input
(H-DRV from the Deflection Processor,
ICM2200, in Main Chassis) at pin 2 of
connector CN1D2. This signal is approximately 9 volts peak at the operating frequency and has a duty cycle of
about 40% high, 60% low.
Current from H-DRV is amplified by transistor Q3200 and Q3201, providing a
low impedance to rapidly drive the gate
of the drive transistor, Q3203. This
action results in an alternating current flow in the primary of driver transformer, TX3200. During Q3203 on time,
energy is stored in TX3200 and rapid
turn off of QX3204 is initiated. During Q3203 off time, the energy previously stored in TX3200 is used to drive
the base of QX3204.
Pincushion Modulator Circuit
This circuit receives a pincushion and
size correction signal. EW-DRV from the
Deflection Processor (ICM2200), Pin 4
of connector CN1D2, modulates the Yoke
current to provide keystone and pincushion geometric correction. EW-DRV
is a vertical deflection rate parabola.
Shutdown Circuit
The flyback pulse voltage from pin 9 of
TX3201 (Flyback Transformer) is peak
detected (rectified) by the action of
diode D3205 and capacitor C3218. This
form a DC voltage appearing on C3218
representative of the CRT anode voltage (HV) produced by TX3201. Precision
resistors R3001, R3002, R3003 and R3004
divide this voltage down. This lower
voltage appears on one input of the
comparator circuit formed by Q3000 and
ZD3003. In the event the CRT anode voltage become excessive, the comparator
circuit output will go to high level at
approximately 5 volts. This signal (HPROT) is send to Deflection Processor
(ICM2200), Pin 7 of connector CN1D2,
causing Horizontal Drive to be disabled and latched, preventing further
generation of anode voltage. The drive
will remain off until power (via remote control or front panel) is cycled
from “Off” to “On”.
Vertical Deflection
The Vertical Deflection circuit, IC2100,
is a linear amplifier that can directly
drive the yoke current (including the
required DC component). The sawtooh
waveforms needed, as inputs, by IC2100
are generated in the Deflection Processor, ICM2200, in Main Chassis, VD+
and VD- pin 11 and 22 of connector
CN1D2.
3828VD0171G 3-2 DIGITAL FCS - CIRCUIT OVERVIEW
Loading...