Installation / Operating Guide | Warranty
Model Numbers | H 2 4 F36DT | H2 5 F36DT | H27F36 DT | H 27 F36 S | Concierge TVs | H32F36DT |
© Copyright 2005, Zenith Electronics Corporation
RECORD TV MODEL NUMBER
For Customer Support/Service please call:
1-888-865-3026
www.zenith.com
The model and serial number of the ConciergeTM TV are located on the back of the TV cabinet. For future convenience, we suggest that you record the numbers here:
MODEL NO.____________________________________
SERIAL NO.____________________________________
WARNING
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING:
TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
POWER CORD POLARIZATION:
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.
NOTE TO CABLE/TV INSTALLER:
This reminder is provided to call the cable TV system installer’s attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical.
REGULATORY INFORMATION:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
CAUTION:
Do not attempt to modify this product in any way without written authorization from Zenith Electronics Corporation. Unauthorized modification could void the user’s authority to operate this product.
COMPLIANCE:
The responsible party for this product’s compliance is:
Zenith Electronics Corporation, 2000 Millbrook Drive, Lincolnshire, IL 60069, USA. Phone: 1-847-941-8000.
2-WIRE COMM-WARN |
ConciergeTM is a trademark of Zenith Electronics Corporation |
|
© Copyright 2005 Zenith Electronics Corporation |
IMPORTANT SAFETY INSTRUCTIONS
This product has been manufactured and tested with yuur safety in mind. Howerver, improper use can result in potential electrical shock or fire hazards. To avoid defeating the safeguards that have been built into the new product, please read and observe the following safety points when installing and using the new product, and save them for future reference.
Observing the simple precautions discussed in this operating guide can help the user get many years of enjoyment and safe operation that are built into the new product.
This product complies with all applicable U.S. Federal safety requirements, and those of the Canadian Standards Association.
1. Read Instructions
All the safety and operating instructions should be read before the product is operated.
2. Follow Instructions
All operating and use instructions should be followed.
3. Retain Instructions
The safety and operating instructions should be retained for future reference.
4. Heed Warnings
All warnings on the product and in the operating instructions should be adhered to.
5. Cleaning
Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
6. Water and Moisture
Do not use this product near water for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool.
7. Accessories
Do not place this product on a slippery or tilted surface, or on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer's instructions, and should use a mounting accessory recommended by the manufacturer.
8. Transporting Product
A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn.
9. Attachments
Do not use attachments not recommended by the product manufacturer as they may cause hazards.
10. Ventilation
Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered.
The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instructions have been adhered to.
11. Power Sources
This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions.
12. Power Cord Polarization
This product is equipped with a polarized alternating-current power plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.
13. Power-Cord Protection
Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.
14. Outdoor Antenna Grounding
If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code (U.S.A.), ANSI/ NFPA 70 provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antennadischarge unit, connection to grounding electrodes, and requirements for the grounding electrode.
(Continued on next page)
PORTABLE CART WARNING |
P A G E 3 |
IMPORTANT SAFETY INSTRUCTIONS
(Continued from previous page)
Example of Grounding According to National Electrical Code Instructions
Ground Clamp |
|
Antenna Lead in Wire |
|
|
|
|
|
|
|
|
Antenna Discharge Unit |
|
|
(NEC Section 810-20) |
|
|
Grounding Conductor |
Electric Service |
|
(NEC Section 810-21) |
|
|
|
Equipment |
|
Ground Clamps |
|
|
|
|
|
Power Service Grounding |
|
|
Electrode System (NEC |
|
|
Art 250, Part H) |
NECNational Electrical Code
result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation.
e.If the product has been dropped or the cabinet has been damaged.
f.If the product exhibits a distinct change in performance.
21. Replacement Parts
When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.
22. Safety Check
Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition.
15. Lightning
For added protection for this product (receiver) during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges.
16. Power Lines
An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.
17. Overloading
Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock.
18. Object and Liquid Entry
Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.
19. Servicing
Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
23. Wall or Ceiling Mounting
The product should be mounted to a wall or ceiling only as recommended by the manufacturer.
24. Heat
The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.
25. CAUTION concerning the Power Cord
Most appliances recommend they be placed upon a dedicated circuit; that is, a single outlet circuit which powers only that appliance and has not additional outlets or branch circuits.
Do not overload wall outlets. Overloaded wall outlets, loose or damage wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer.
Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance.
20. Damage Requiring Service
Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:
a.If the power-supply cord or plug is damaged.
b.If liquid has been spilled, or objects have fallen into the product.
c.If the product has been exposed to rain or water.
d.If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may
26. Outdoor Use Marking
WARNING - To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.
27. Wet Location Marking
Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus.
P A G E 4
Table of Contents
Use the steps outlined below as a setup guide and to determine the TV features that will require adjustment for the needs of the user
Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Important Safety Instructions . . . . . . . . . . . . . . . . 3 - 4
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Step 1. Hook Up TV to Signal Source(s) etc.
TV and other Equipment Hookups
Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Cable service . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Antenna with VCR . . . . . . . . . . . . . . . . . . . . . . . . 8 Cable service with VCR . . . . . . . . . . . . . . . . . . . . . 9 S-Video device . . . . . . . . . . . . . . . . . . . . . . . . . 10 External Speaker . . . . . . . . . . . . . . . . . . . . . . . . 11
Step 2. Channel Search and Reception Setup
Auto Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
(Select Antenna, or cable service and do channel search)
Front Panel Controls . . . . . . . . . . . . . . . . . . . . . . . . 13
Guest’s Remote Key Functions . . . . . . . . . . . . . . . . . 14
Installer’s Remote Key Functions . . . . . . . . . . . . . . . . 15
On-Screen Menus Overview . . . . . . . . . . . . . . . . . . . . 16
Step 3. Customize the TV’s Features
Setup Menu (Start with page 12, Auto Program) Add/Del/Blank . . . . . . . . . . . . . . . . . . . . . . . . . 17 Channel Labels . . . . . . . . . . . . . . . . . . . . . . . . . 18
Clock Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Timer (On/Off Timers) . . . . . . . . . . . . . . . . . . . . 20
Captions (Caption/Text) . . . . . . . . . . . . . . . . . . . 21
Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Audio Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Bass, Treble, Balance, Audio Mode,
Front Surround, Sound Rite, Speakers
Video Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Contrast, Brightness, Color, Tint, Sharpness, Picture Pref.
Installer Parental Control Menu . . . . . . . . . . . . 25 - 26
Set up Parental Control
Other Menus and On-Screen Displays . . . . . . . . . . . . 27
Managing the Channel Banks . . . . . . . . . . . . 28 - 29 - 30
Installer Menus . . . . 31 - 32 - 33 - 34 - 35 - 36 - 37 - 38
LT2000 Quickset II Clone Programmer . . . . . . 39 - 40 - 41
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Trouble Shooting . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Guest Operation Section (Copy for Guest Usage)
Guest Remote Control Key Functions . . . . . . . . . . . . . 44 Guest Parental Control Menu . . . . . . . . . . . . . . . 45 - 46 Guest Menus and On-Screen Displays . . . . . . . . . . . . . 47 Warranty for Concierge Series TVs . . . . . . . . . . Back Cover
Installer/Hotel Note:
Pages 44, 45, 46, and 47 contain information and menus which the guest can use to operate the TV. It is recommended that these four pages be copied and included with the literature packet that the lodge provides to guests.
Purchase the Optional Installer’s Remote and Clone Programmer
To preform a normal installation set up, you need an installer’s remote like the LP702, and the LT2000 Quickset II Clone Programmer - - both are shown and described in later sections. The installer remote allows access to the Installer and, User menus. The installer remote has Menu, Select, and Adjust keys (Down/Left/Right arrow) keys. The LT2000 Quickset II Clone Programmer is used to duplicate a TV’s setup and install it on another identical TV. See your Zenith Dealer.
Design and specifications are subject to change without prior notice.
P A G E 5
Hook Up an Antenna to the TV
Connect an off-air antenna to the TV
1 |
Locate the Antenna/Cable jack on the back of the TV. |
2 |
Connect the antenna wire that runs from the wall |
|
directly to this jack, according to one of the diagrams |
|
to the right. |
3 |
Remove the back of the remote and put in two AA |
|
batteries. |
Antenna |
TV Back |
|
Antenna |
|
Matrix |
|
|
Out |
|
|
Cable |
|
|
|
|
|
|
Flat Wire |
|
Video |
R- Audio - L |
|
In |
||
(300 ohm) |
|
In |
|
|
|
||
|
|
|
|
|
M.P.I. |
|
|
|
|
S-Video |
R- Audio - L |
|
|
In |
|
|
|
In |
|
|
|
|
300/75 ohm Adapter
|
Back of |
|
|
|
|
|
Remote |
|
|
|
|
4 |
Plug in the TV. The TV is designed to operate on stan- |
|
|
|
|
|
dard current, 120-volt 60 Hertz AC. Do not attempt to |
|
|
|
|
|
operate it on DC power. |
|
|
|
|
|
|
|
|
TV Back |
|
|
|
Antenna |
|
|
|
|
120 V AC |
|
|
|
|
|
60 Hz |
|
|
|
|
|
|
|
Antenna |
|
Matrix |
|
|
|
|
Out |
|
|
|
|
Cable |
|
|
5 |
|
|
|
|
|
Go to page 12 to Auto Program the TV. |
|
|
Video |
R- Audio - L |
|
|
|
|
|
In |
In |
|
|
RF Coaxial Wire |
|
|
|
|
|
M.P.I. |
|
|
|
|
|
(75ohm) |
|
|
|
|
|
|
|
|
|
|
|
|
|
S-Video |
R- Audio - L |
|
|
|
|
In |
|
|
|
|
|
In |
|
|
|
|
|
|
If you have a 75 ohm RF cable, then you don’t need any adapters!
A 300 to 75 ohm adapter is not included with the
Zenith TV.
Mini glossary
75 OHM RF CABLE
300 TO 75 OHM ADAPTER
The wire that comes from an off-air antenna or cable service provider. Each end looks like a hex shaped nut with a wire sticking through the middle, and it screws onto the threaded jack on the back of your TV.
A small device that connects a two-wire 300 ohm antenna to a 75 ohm RF jack. They are usually about an inch long with two screws on one end and a round opening with a wire sticking out on the other end.
P A G E 6
Hook Up Cable (CATV) to the TV
Connect cable service to the TV
Cable TV
Wall Jack
1 |
Locate the Antenna/Cable jack on the back |
|
of the TV. |
2 |
Connect the wire that runs from the wall directly |
|
to this jack, according to one of the diagrams to |
|
the right. |
3 |
Remove the back of the remote and put in |
|
two AA batteries. |
|
Back of |
|
Remote |
4 |
Plug in the TV. The TV is designed to operate on |
|
normal current, 120-volt 60 Hertz AC. Do not |
|
attempt to operate it on DC power. |
|
120 V AC |
|
60 Hz |
5 |
Go to page 12 to Auto Program the TV. |
|
If you’re using a cable box, leave the TV on channel 3 |
|
or 4 and use your cable box to change channels. |
|
If you’re using a cable box, Auto Program might only |
|
find the channel your cable service is on (usually chan- |
|
nel 3 or 4). Don’t worry, that’s all you need! |
Round Wire
(75ohm)
Cable TV
Wall Jack
In |
Cable Box |
||
Out |
output |
|
|
switch |
3 4 |
||
|
RF Coaxial Wire
(75ohm)
TV Back
Antenna |
|
Matrix |
|
Out |
|
Cable |
|
|
|
|
|
|
Video |
R- Audio - L |
|
In |
|
|
In |
|
|
|
|
M.P.I. |
|
|
|
S-Video |
R- Audio - L |
|
In |
|
|
In |
|
|
|
TV Back
Antenna |
|
Matrix |
|
Out |
|
Cable |
|
|
|
|
|
|
Video |
R- Audio - L |
|
In |
|
|
In |
|
|
|
|
M.P.I. |
|
|
|
S-Video |
R- Audio - L |
|
In |
|
|
In |
|
|
|
P A G E 7
Hook Up Antenna and VCR to the TV
Connect an off-air antenna and VCR to the TV
1 Locate the Antenna/Cable In jack on the back of the VCR.
2 Connect the wire that runs from the antenna, according to one of the diagrams to the right. As required, make the other connections as shown to the right.
3 Remove the back of the remote, put in two AA batteries.
Back of
Remote
Antenna
|
|
|
VCR Back |
|
|
VCR Back AV Panel |
|
|
|
In |
output |
|
Flat Wire |
|
switch 3 4 |
|
(300 ohm) |
Out |
Video Audio |
|
|
||
TV Back |
|
300/75 ohm |
|
|
Adapter |
|
Antenna |
|
Matrix |
|
|
Out |
|
|
Cable |
|
|
|
|
|
A/V cables |
|
|
|
|
|
|
|
|
not included |
Video |
R- Audio - L |
with TV |
|
In |
|
In |
|
|
|
|
|
M.P.I. |
|
|
|
S-Video |
R- |
L |
|
In |
|
||
|
|
|
4 |
Plug in the TV. The TV is designed to operate on |
|
standard current, 120-volt 60 Hertz AC. Do not |
attempt to operate it on DC power.
Antenna
VCR Back
120 V AC
60 Hz
VCR Back AV Panel
In output switch 3 4
5 |
Go to page 12 to Auto Program the TV. |
RF Coaxial Wire |
Out Video Audio |
(75ohm) |
|
TV Back
No A/V cables are included with the Zenith TV.
Without A/V cables, most VCRs will not play videocassettes in stereo sound.
Antenna |
|
Matrix |
|
|
Out |
|
|
Cable |
|
|
|
|
|
A/V cables |
|
|
|
|
|
|
|
|
not included |
Video |
R- Audio - L |
with TV |
|
In |
|
In |
|
M.P.I. |
|
|
|
S-Video |
R- |
L |
|
In |
|
||
|
|
|
P A G E 8
Hook Up Cable Service (CATV) and VCR
Connect a VCR and Cable service to the TV
1 |
Locate the Antenna/Cable In jack on the back of |
|
the VCR. |
2 |
Connect the wire that runs from the wall, accord- |
|
ing to one of the diagrams to the right. As |
|
required, make the other connections as shown to |
|
the right. |
3 |
Remove the back of the remote, put in |
|
two AA batteries. |
|
Back of |
|
Remote |
4 |
Plug in the TV. The TV is designed to operate on |
|
standard current, 120-volt 60 Hertz AC. Do not |
|
attempt to operate it on DC power. |
|
120 V AC |
|
60 Hz |
5 |
Go to page 12 to Auto Program the TV. |
|
Leave the VCR and the television tuned to channel three |
|
and use the cable box to change channels. |
|
No A/V cables are included with your TV. Without A/V |
|
cables, most VCRs will not play videocassettes in stereo |
|
sound. |
Cable TV
Wall Jack
|
|
VCR Back |
|
VCR Back AV Panel |
|
|
In |
output |
|
|
switch 3 4 |
RF Coaxial Wire |
Out |
Video Audio |
(75ohm) |
|
|
TV Back
Antenna |
|
Matrix |
|
|
Out |
|
|
Cable |
|
|
|
|
|
A/V cables |
|
|
|
|
|
|
|
|
not included |
Video |
R- Audio - L |
with TV |
|
In |
|
In |
|
M.P.I. |
|
|
|
S-Video |
R- |
L |
|
In |
|
||
|
|
|
In |
Cable Box |
|
|
Out |
output |
|
|
switch 3 |
4 |
|
|
|
|
||
|
|
|
VCR Back |
|
|
VCR Back AV Panel |
|
|
|
In |
output |
|
|
|
switch 3 4 |
|
RF Coaxial Wire |
Out |
Video Audio |
|
(75ohm) |
|
|
TV Back
Antenna |
|
Matrix |
|
|
Out |
|
|
Cable |
|
|
|
|
|
A/V cables |
|
|
|
|
|
|
|
|
not included |
Video |
R- Audio - L |
with TV |
|
In |
|
In |
|
|
|
|
|
M.P.I. |
|
|
|
S-Video |
R- |
L |
|
In |
|
||
|
|
|
P A G E 9
S-Video Hook Up
Connect an external S-Video device to the TV
S-Video Device
1 |
Locate the S-Video out jack on the back of the |
|
VCR or other S-Video device. |
2 |
Connect the S-Video cable from the device to the |
|
TV S-Video In jack, according to the diagram to |
|
the right. As required, make the other audio con- |
|
nections as shown to the right. |
3 |
Remove the back of the remote, put in |
|
two AA batteries. |
|
Back of |
|
Remote |
4 |
Plug in the TV. The TV is designed to operate on |
|
standard current, 120-volt 60 Hertz AC. Do not |
|
attempt to operate it on DC power. |
|
120 V AC |
|
60 Hz |
5 |
Go to page 12 to Auto Program the TV. |
Audio Out |
S-Video Out |
S-Video |
R L |
|
Device |
|
|
Connections |
|
|
Panel |
S-Video cable not included with TV
TV Back
Antenna |
|
Matrix |
|
Out |
|
Cable |
|
|
|
|
|
|
Video |
R- Audio - L |
|
In |
|
|
In |
|
|
|
|
M.P.I. |
|
|
|
S-Video |
R- Audio - L |
|
In |
|
|
In |
|
|
|
No S-Video cable or audio cables are provided with the TV. Since S-Video is for Video only, you must connect audio cables or there will be no sound for the S-Video source.
P A G E 1 0
External Speaker Hook Up
Connect an external speaker to the TV
1 |
Locate the Audio In jack on the back of the |
|
speaker. |
2 |
Connect a standard audio cable from the |
|
Matrix Out jack on the TV, to the Audio In |
jack on the external speaker.
TV Back
Antenna |
|
Matrix |
|
Out |
|
Cable |
|
|
|
|
|
|
Video |
R- Audio - L |
|
In |
|
|
In |
|
|
|
|
M.P.I. |
|
|
|
S-Video |
R- Audio - L |
|
In |
|
|
In |
|
|
|
Speaker Back
Audio In
A/V cables not included with TV
P A G E 1 1
Auto Program (Channel Search)
Use Auto Program to specify Antenna or cable service incoming signal source and automatically store all of the channels that are found by channel search
1 |
|
|
|
With the optional Installer remote control in hand, press |
|
|
|
|
|
the POWER key to turn on the TV. |
|
2 |
|
|
|
Press MENU repeatedly until the Setup menu appears. |
1 |
3 |
|
|
|
Using SELECT on the remote control, highlight Auto |
|
|
|
|
|
Program on the screen. |
|
4 |
|
|
|
Press the Right or Left ADJ (Adjust) arrow to go to the |
|
|
|
|
|
Auto Program menu. |
|
5 |
|
|
|
Using SELECT, choose either Cable TV or Off-Air Antenna |
|
|
|
|
|
on your screen. (The flashing option is selected.) |
|
6 |
|
|
|
Press the Right or Left ADJ arrow to begin the Channel |
|
|
|
|
|
Search. |
|
7 |
|
|
|
Press ENTER when finished. |
|
|
|
|
|
|
3/5 |
|
|
|
|
Auto Program finds channels being received by the TV tuner. |
|
|
|
|
|
|
|
|
|
|
|
Cable will not work unless a cable service is present. |
4/6 |
|
|
|
|
||
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
AUTO PROGRAM |
TO PROGRAM |
ADD/DEL/BLNK |
|
CH. LABELS
CLOCK SET
TIMER
CAPTIONS
LANGUAGE
POWER
MUTE
|
FLSHBK |
CC |
|
TV/FM |
|
UME |
|
VOL |
CHANNEL |
|
1 2 3
4 5 6
7 8 9
0 ENTER
7
2
TIMER MENU |
ALARM |
SELECT |
CH PREVIEW |
ADJ |
ADJ |
Mini glossary |
|
OFF-AIR-ANTENNA |
If the guest can only view over-the-air broadcasts, select Antenna. |
CABLE |
If you provide cable service to your guests, select Cable. |
P A G E 1 2
Front Panel Controls
Use the front control panel to access the menus or just operate the TV
Note: Item 10 Key Defeat, in the installer’s menu allows the installer to:
Set Menu Option 10, Key defeat to “0” - Front panel controls give access to menus. Set Menu Option 10, Key defeat to “1” - Menus not available with front panel controls.
A |
|
|
|
Press POWER to turn the TV on. |
1 |
|
|
|
To access the menus, press the MENU button on |
|
|
|
|
the control panel. Cycle through the various |
|
|
|
|
menus by pressing MENU repeatedly. |
2 |
|
|
|
Use the SELECT button to highlight the option |
|
|
|
|
you want to modify. |
3 |
|
|
|
Use either the Right or Left ADJUST button to |
|
|
|
|
modify the option you have chosen. |
D |
|
|
|
Press CAPTIONS to turn captions on and off. |
|
|
|
|
The menu will disappear after a few seconds. |
A |
|
|
|
TV Operation |
|
|
|
Power turns the TV on and off. |
|
B |
|
|
|
Channel Up/Down tunes to next channel. |
C |
|
|
|
Volume Up/Down adjusts sound level. |
D |
|
|
|
Captions turns selected Caption/Text option on |
|
|
|
|
and off. |
E |
|
|
|
Camport: Front Audio/Video Inputs |
|
|
|
Video Input |
|
F |
|
|
|
L-Audio-R Inputs |
|
|
|
|
Used for stereo sound from various types of |
|
|
|
|
equipment. |
|
|
|
|
You can use Channel to tune to available channels and |
|
|
|
|
|
|
|
|
|
Volume to set the sound level, regardless of the key |
|
|
|
|
|
|
|
|
|
defeat setting. |
Typical Front Panel Controls
captions |
volume |
channel |
power |
D C A B
adjust select menu
video in |
L audio R |
|
|
F |
1 |
||
|
|
E |
3 2
P A G E 1 3
Guest Remote Key Functions
A quick list of the keys on the guest remote and what they do
CC (CLOSED CAPTIONING)
Direct access to closed captions. Press ENTER to exit.
POWER
Turns TV On or Off.
VOLUME (LEFT/RIGHT)
Adjusts the sound level.
ENTER
Press to view the Channel/Time/Audio display or to remove any on-screen display or menu.
TIMER
Press repeatedly to set the TV turn-off time from 10 minutes up to 4-hours. Sets AM or PM in Clock/Alarm menus.
POWER |
|
|
MUTE |
CC |
FLSHBK |
|
|
UME |
|
VOL |
CHANNEL |
|
1 2 3
4 5 6
7 8 9
0 ENTER
TIMER |
ALARM |
CH PREVIEW
remote control part number
SC652Z
124-213-18 6710V00108A
NOTE:
The channel and volume keys can be used by the guest to select and adjust the Parental Control settings, if the installer activates the Parental Control (V-CHIP) option in the Installer menu.
FLASHBK (FLASHBACK)
Returns to the last channel viewed.
MUTE
Turns sound Off and On, while the picture remains.
CHANNEL (UP/DOWN)
Scrolls through available channels, and the Video Channel (Audio/Video source).
NUMBER KEYPAD
Used to key-in numbers and select channels directly: key-in channel numbers and press ENTER to go to new channel.
ALARM
Press to go to the Alarm menu. Set a time for the TV to turn itself on.
CHANNEL PREVIEW
Displays the available TV channels, including access to guest’s Parental Control menu (if Active). Allows guest to select the Video source. (Use the Audio/Video jacks on the back of the TV as the source of the picture and sound.)
P A G E 1 4
Installer Remote Key Functions
A quick list of the keys on the optional LP702 installer’s remote and what they do
CC (CLOSED CAPTIONING)
Direct access to closed captions. Press ENTER to exit.
POWER
Turns TV On or Off.
TV/FM
Selects TV or Radio mode on TVs equipped with FM radio.
VOLUME (LEFT/RIGHT)
Adjusts the sound level.
ENTER
Press to view the Channel/Time display or to remove any on-screen display or menu.
TIMER
Press repeatedly to adjust TV turn-off time from 10 minutes up to 4-hours.
Sets AM or PM in Clock/Alarm menus.
MENU/SELECT/ADJ (ADJUST)
Adjusts on-screen menus and options. Press MENU repeatedly to scroll through menus. Use SELECT to choose an option and ADJ (adjust) Left/Right to change the selected option.
POWER
MUTE
|
FLSHBK |
CC |
|
TV/FM |
|
UME |
|
VOL |
CHANNEL |
|
1 2 3
4 5 6
7 8 9
0 ENTER
TIMER MENU |
ALARM |
SELECT |
CH PREVIEW |
ADJ |
ADJ |
FLASHBK (FLASHBACK)
Returns to the last channel viewed.
MUTE
Turns sound Off and On, while the picture remains.
CHANNEL (UP/DOWN)
Chooses next available channel.
NUMBER KEYPAD
Used to key-in numbers and select channels directly: key-in channel numbers and press ENTER to go to new channel.
ALARM
Press to go to the Alarm menu. Set a time for the TV to turn itself on.
CHANNEL PREVIEW
Gives installer access to the guest’s menus. Displays the available TV channels and hotel guest’s Parental Control menu (if active). Selects the Video source. (Use the Audio/Video jacks on the back of the TV as the source of the picture and sound.)
remote control part number
LP702
124-213-04
P A G E 1 5