LG GR-P247JHM User Guide

P/NO : MFL62377410

Entry

Important safety instruction

Identification of parts

Where to install

Door removal

Door replacement

Feed water pipe installation

Height adjustment

Starting

Adjusting the temperatures and functions

Refreshment center

Shelf

Egg box

Nano charcoal deodorizer

LED lamp (Freezer/Fridge)

Fresh compartment

Vacuum fresh compartment

Freezer/Fridge basket

Dairy corner

How to exchange the water purifier filter

Location of foods

Storing foods

General information

Cleaning

Trouble shooting

It is normal…

When replacing PANEL…….

Table of contents

Introduction

Installation

Operation

Suggestion on

food storage

Care and

maintenance

31 31



This product is exclusive use at 220V/50Hz.



You should purchase transformer of more than 2.0KVA when you want to use it at the 110V area.

Entry

The model and serial numbers are found on the inner case or back of refrigerator compartment of this unit. These numbers are unique to this unit and not available to others. You should record requested information here and retain this guide as a permanent record of your purchase. Staple your receipt here.

Date of purchase : Dealer purchased from : Dealer address : Dealer phone no. : Model no. : Serial no. :

Before it is used, this refrigerator must be properly installed and located in accordance with the installation instructions in this document.

Never unplug your refrigerator by pulling on the power cord. Always grip plug firmly and pull it straight out from the outlet.

When moving your appliance away from the wall, be careful not to roll over the power cord or to damage it in any way.

After your refrigerator is in operation, do not touch the cold surfaces in the freezer compartment, particularly when your hands are damp or wet. Skin could adhere to these extremely cold surfaces.

Unplug the power cord from the power outlet for cleaning or other requirements. Never touch it with wet hands because you can get an electric shock or be hurt.

Never damage, process, severely bend, pull out, or twist the power cord because damage the power cord may cause a fire or electric shock. You have doubts on whether the appliance is properly grounded.

Never place glass products in the freezer because they may be broken due to expansion when their contents are frozen.

Never allow your hands within the ice storage bin of the automatic ice maker. You could be hurt by the operation of the automatic ice maker.

The appliance is not intended for use by young children or infirm persons without supervision.

Young children should be supervised to ensure that they do not play with the appliance.

Never allow anyone to climb, sit, stand or hang on the refreshment center door. These actions may damage the refrigerator and even tip it over, causing severe personal injury.

If possible, connect the refrigerator to its own individual electrical outlet to prevent it and other appliances or household lights from causing an overload that could cause a power outage.

The refrigerator-freezer should be so positioned that the supply plug is accessible for quick disconnection when accident happens.

If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.

Do not modify or extend the Power Cord length.



It will cause electric shock or fire.

Introduction

Important safety instruction

Don’t use an

extension cord

Accessibility of

Supply Plug

Supply Cord

Replacement

WARNING

Introduction

DANGER: Risk of child entrapment. Before you throw away your old refrigerator or freezer: Take off the doors but leave the shelves in place so that children may not easily climb inside. The appliance is not intended for use by young children or infirm persons without supervision. Young children should be supervised to ensure that they do not play with the appliance.

Don’t store or use gasoline or other flammable vapor and liquids in the vicinity of this or any other appliance.

In the event of an electric short circuit, grounding (earthing) reduces the risk of electric shock by providing an escape wire for the electric current. In order to prevent possible electric shock, this appliance must be grounded improper use of the grounding plug can result in an electric shock. Consult a qualified electrician or service person if the grounding instructions are not completely understood, or if you have doubts on whether the appliance is properly grounded.

Child entrapment

Don’t store

Grounding (Earthing)

This appliance contains a small amount of isobutane refrigerant (R600a), natural gas with high environmental compatibility, but it is also combustible. When transporting and installing the appliance, care should be taken to ensure that no parts of the refrigerating circuit are damaged. Refrigerant squirting out of the pipes could ignite or cause an eye injury. If a leak is detected, avoid any naked flames or potential sources of ignition and air the room in which the appliance is standing for several minutes.

In order to avoid the creation of a flammable gas air mixture if a leak in the refrigerating circuit occurs, the size of the room in which the appliance may be sited depends on the amount of refrigerant used. The room must be 1m2in size for every 8g of R600a refrigerant inside the appliance. The amount of refrigerant in your particular appliance is shown on the identification plate inside the appliance. Never start up an appliance showing any signs of damage. If in doubt, consult your dealer.

Keep ventilation openings, in the appliance enclosure or in the built-in structure, clear of obstruction.

Do not use mechanical devices or other means to accelerate the defrosting process, other than those recommended by the manufacturer.

Do not damage the refrigerant circuit.

Do not use electrical appliances inside the food storage compartments of the appliance, unless they are of the type recommended by the manufacturer.

The refrigerant and insulation blowing gas used in the appliance require special disposal procedures. When disposal, please consult with service agent or a similarly qualified person.

WARNING

Introduction

BASIC SAFETY PRECAUTIONS

This guide contains many important safety messages. Always read and obey all safety messages.

This is the safety alert symbol. It alerts you to safety messages that inform you of hazards that can kill or hurt you or others or cause damage to the product. All safety messages will be preceded by the safety alert symbol and the hazard signal word DANGER, WARNING, or CAUTION. These words mean:

All safety messages will identify the hazard, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

DANGER

You will be killed or seriously injured if you don’t follow instructions.

WARNING

You can be killed or seriously injured if you don’t follow instructions.

WARNING

To reduce the risk of fire, electric shock, or injury to persons when using your product, basic safety precautions should be followed, including the following.

Read all instructions before using this appliance.

CAUTION

Indicates an imminently hazardous situation which, if not avoided, may result in minor or moderate injury, or product damage only.

1. When connecting the power

The dedicated outlet should be used.

• Using several devices at one outlet may cause fire.

• The electric leakage breaker may damage food and the dispenser may be leaked.

Do not allow the power plug to face upward or to be squeezed at the back of the refrigerator.

Water may be flown into or the plug may be damaged, which causes fire or electric shock.

Do not allow the power cord bent or pressed by the heavy object to be damaged.

It may damage the power cord to cause fire or electric shock.

Introduction

Do not extend or modify the length of the power plug.

It causes electric shock or fire by the electric damage of the power cord or others.

Unplug the power plug when cleaning, handling or replacing the interior lamp of the refrigerator.

• It may cause electric shock or injury.

• When replacing the interior lamp of the refrigerator, make

sure that the rubber ring for preventing the electric spark within the socket is not taken off.

Do not pull out the cord or touch the power plug with wet hands.

• It may cause electric shock or injury.

Remove water or dust from the power plug and insert it with the ends of the pins securely connected.

Dust, water or unstable connection may fire or electric shock.

Make sure of grounding.

The incorrect grounding may cause breakdown and electric shock.

Ground

Wire

Copper

Flat

More than

30 inches

When the power cord or the power plug is damaged or the holes of the outlet are loosed, do not use them.

It may cause electric shock or short circuit to make fire.

2. When using the refrigerator

Do not place the heavy object or the dangerous object (container with liquid) on the refrigerator.

It may be dropped to cause injury, fire or electric shock when opening or closing the door.

Do not install the refrigerator in the wet place or the place which water or rain splashes.

Deterioration of insulation of electric parts may cause electric leakage.

Introduction

2. When using the refrigerator

Do not cling to the door or the shelves of the door or the home bar of the freezer or the cool chamber.

It may make the refrigerator fallen down or damage the hands. Especially, do not allow the children to do the above.

Do not use or store inflammable materials ether, benzene, alcohol, medicine, LP gas, spray or cosmetics near or in the refrigerator.

It may cause explosion or fire.

Benzene



Ether

Thinner

Do not place the lit candle within the refrigerator to deodorize.

It may cause explosion or fire.

Do not insert the hands into the ice bucket or the ice dispenser.

Operating the ice maker may cause injury.

Do not store the medicine or the academic materials at the refrigerator.

When the material with the strict temperature control is stored, it may be deteriorated or it may make an unexpected reaction to cause any risk.

The Academic

Medicine

Do not use the combustible spray near the refrigerator.

It may cause fire.

Introduction

Avoid the heating devices.

It may cause fire.

Do not place flower vase, cup, cosmetics, medicine or any container with water on the refrigerator.

It may cause fire, electric shock or injury by dropping down.

Use the submerged refrigerator after checking it.

It may cause electric shock or fire.

When gas is leaked, do not touch the refrigerator or the outlet and ventilate the room immediately.

• The explosion by spark may cause fire or burn.

• Because this refrigerator uses natural gas (isobutene,

R600a) as the environment-friendly refrigerant, even a small amount (80~90g) is combustible. When the gas is leaked by the severe damage during delivering, installing or using the refrigerator, any spark may cause fire or burn.

Do not spray water at the outside or the inside of the refrigerator or do not clean it with benzene or thinner.

Deterioration of insulation of electric parts may cause electric shock or fire.

T hinn

Thinner

When any strange smell or smoke is detected from the refrigerator, disconnect the power plug immediately and contact to the service center.

It may cause fire.

Service

center

Do not allow any person except the qualified engineer to disassemble, repair or alter the refrigerator.

It may cause injury, electric shock or fire.

Introduction

Do not use the refrigerator for non-domestic purpose (storing medicine or testing material, using at the ship, etc.).

It may cause an unexpected risk such as fire, electric shock, deterioration of stored material or chemical reaction.

When disposing the refrigerator, remove the packing materials from the door.

It may cause to lock out the child.

Install the refrigerator on the solid and level floor.

Installing it on the unstable place may cause death by falling down the refrigerator when opening or closing the door.

Do not insert the hands or the metal stick into the exit of cool air, the cover, the bottom of the refrigerator, the heatproof grill (exhaust hole) at the backside.

It may cause electric shock or injury.

Do not touch food or containers at the freezer with wet hands.

It may cause frostbite.

CAUTION

Violating this direction may cause injury or damage house or furniture. Always be careful, please.

Do not put ice in thin crystal cup or ceramic ware.

It may break cup or ceramic ware to cause injury.

2. When using the refrigerator

Introduction

When the electricity is off, remove ice from the ice bucket (only for the model with the dispenser).

The long-time power failure may thaw ice to damage the floor. When the long-time power failure is expected, remove ice from the ice bucket.

Supply the automatic ice maker with drinkable water only (only for the model with the dispenser).

Otherwise, it may cause any risk.

Drinkable

water

Wait for 5 minutes or longer when reconnecting the plug.

It may cause the operation of the freezer to fail.

After 

5minutes

Do not put bottle in the freezer.

It may freeze the contents to break the bottle to cause injury.

Pull out the power plug not by grasping the cord but the plug of its end.

It may cause electric shock or short circuit to fire.

Do not install the refrigerator in the wet place or the place which water or rain splashes.

Deterioration of insulation of electric parts may cause electric leakage.

Do not insert the hands into the bottom of the refrigerator.

The iron plate of the bottom may cause injury.

Carry the refrigerator with the handle bar at the bottom of the front and the top of the rear.

Otherwise, your hands may be slipped to cause injury.

Introduction

Identification of parts

•

Parts, features, and options vary by model. Your model may not include every option.

NOTE

Freezer Compartment

Refrigerator Compartment

Milk product corner

LED Lamp

Automatic

Icemaker

Shelf

Door rack

Drawer(2)

Door rack

Lower cover

Shelf

Can Server

Refreshment center Nano charcoal deodorizer

Egg Box

LED Lamp

Filter

Door Rack

Fresh compartment

Vacuum fresh compartment

Because opening or closing the door of the refrigerator may cause injury to the person around it, be careful, please.

Opening or closing the door may cause feet or hands to be caught in the chink in door or the child to be get hurt by the corner.

Do not put any living animal in the refrigerator.

CAUTION

Violating this direction may cause injury or damage house or furniture. Always be careful, please.

Installation

1. Place your appliance where it is easy to

use.

2. Avoid placing the unit near heat sources,

direct sunlight or moisture.

3. To ensure proper air circulation around the

fridge -freezer, please maintain sufficient space on both the sides as well as top and maintain at least 2 inches (5 cm) from the rear wall.

4. To avoid vibrations, the appliance must

be leveled.

5. Don't install the appliance below 5°C. It may cause affect the performance.

Select a good

location

Where to Install

Disposal of the

old appliance

This appliance contains fluid (refrigerant, lubricant)and is made of parts and materials which are reusable and/or recyclable. All the important materials should be sent to the collection center of waste material and can be reused after rework (recycling). For take back, please contact with the local agency.

Installation

Door removal

Electric Shock Hazard

Disconnect electrical supply to refrigerator before installing. Failure to do so could result in death or serious injury.

If your access door is too narrow for the refrigerator to pass through, remove the refrigerator door and pass the refrigerator laterally.

Remove the lower cover by lifting upward, and remove clip, and then pull up the feed water tube while pressing area  shown in the figure to the right.

Remove lower

cover and

then feed water

tube

Remove the

freezer

compartment

door

Remove the

refrigerator

door

1) Removing the hinge cover by loosening the screws. Separate all connection wires except for the earth line after.

2) Remove the keeper by rotating it counter clockwise () and then lifting the upper hinge up ().

3) Remove the freezer compartment door by

lifting it upward. This time, the door should be lifted enough for the feed water pipe tube to be completely pulled out.

1) Loosen the hinge cover screws and

remove the cover. Remove connection wire, if any, except for the earth line.

2) Remove keeper by rotating it clockwise

() and then remove the upper hinge by lifting it up ( ).

3) Remove the refrigerator compartment

door by lifting it up.

•

If a tube end is deformed or abraded, cut the part away.

NOTE

•

When removing the upper hinge, be careful that the door does not fall forwards .

NOTE

•

Move the refrigerator compartment door passing through the access door and lay it down, but be careful not to damage the feed water pipe tube.

NOTE

Lower cover

Lower hinge

Keeper

Feed water tube

Connection wires

Hinge cover

Upper hinge

Keeper

Upper hinge

Ground Line

Upper hinge

Connection

wires

WARNING

Installation

Door replacement

Feed water pipe installation

Pass the refrigerator laterally through the access door as shown in the right figure.



Automatic ice maker operation needs water pressure of 147~834 kPa (1.5~8.5 kgf/cm2) (That is, an instant paper cup (180 cc) will be fully filled within 3 sec.).



If water pressure does not reach the rating 147 kPa (1.5 kgf/cm2) or below, it is necessary to purchase a separate pressure pump for normal automatic icing and cool water feed.



Keep the total length of the feed water pipe tube within 8 m and be careful for the tube not be bent. If the tube is 8 m or longer it may cause trouble in water feed owing to the drain water pressure.



Install the feed water pipe tube at a place free from heat.



Connect to potable water supply only.



Refer to instructions with water filter kit for installation.

Mount them in the reverse sequence of removal after they pass through the access door.

Pass the

refrigerator

Before

installation

M a x

R Z

E M P R E F T E M P

M i n

M a x

WARNING

Installation

Height adjustment

- When the height of the door may not be leveled when the floor is not leveled.

 When the freezer door is lower – 

Use the (-) driver or spanner to turn the groove or nut of the height adjustment screw on the left to the counterclockwise direction to level the door.

 When the fridge door is lower – 

Use the (-) driver or spanner to turn the groove or nut of the height adjustment screw on the right to the clockwise direction to level the door.

The refrigerator doors will close smoothly by heightening the front side by adjusting the height adjusting screw. If the doors do not close correctly, performance may be affected.

When the floor is

not leveled

 When the fridge door is lower than the freezer door while using the

refrigerator, level the doors.

1. Use the  tool for adjustment on

the wide side to turn nut  ( ) in the clockwise direction to loosen the keeper nut.

2. Use the  tool for adjustment on

the narrow side to turn the adjustment hinge pin  in

( )clockwise direction or ( ) counterclockwise direction to adjust the height of the fridge and freezer doors.

3. After aligning the height of the door, turn the keeper nut in counterclockwise

direction tightly.

When the fridge

door is lower than

the freezer door

After leveling the

door height

Keeper nut

Adjustment hinge pin

Tool for adjustment

Down

Height difference

When using 

the driver

When using 

the spanner

1. Wipe off all dust accumulated during shipping and clean your appliance thoroughly.

2. Install accessories such as the ice cube box, cover evaporating tray, etc., in their

proper places. They are packed together to prevent possible damage during shipping.

3. Connect the power supply cord (or plug) to the outlet. Don't double up with other

appliances on the same outlet.

Do not force too hard to level the height. The hinge pin can be pulled out. (Adjustable range of height is a maximum of 2" (5 cm))

CAUTION

Operation

Refreshment Center

Function display board

Display Power Saving Mode

•

Your model may not include every option.

NOTE

Starting

When your refrigerator is first installed, allow it to stabilize at normal operating temperatures for 2-3 hours prior to filling it with fresh or frozen foods. If operation is interrupted, wait 5 minutes before restarting.

Adjusting the temperatures and functions

Operation

This function save the display power

Press the and buttons simultaneously and hold them for 5 seconds until the Ding sounds. All LED/LCDs will then turn ON, then OFF. When the power saving mode is activated, the display will remain off until the next time the door is opened. Then, it will come on whenever a door is opened or a button is pressed and remain on for 20 seconds after the last door opening or button selection. To deactivate the power saving mode, press the and buttons simultaneously and hold them for 5 seconds until the Ding sounds.



The actual inner temperature varies depending on the food status, as the indicated setting temperature is a target temperature, not actual temperature within refrigerator.



Refrigeration function is weak in the initial time. Please adjust temperature as above after using refrigerator for minimum 2~3 days.

Freezer Compartment

temperature adjustment

Setting

temperature

Setting

temperature

Refrigerator Compartment

temperature adjustment

You can adjust temperature of and freezer room and refrigerator room.

Freezer

control

Display power

saving

Refrigerator

control

Operation



The automatic icemaker can automatically make 6 cubes at a time, 25~35 pieces per day. This quantity may vary by circumstance, including ambient temperature, door opening, freezer load. etc.



Icemaking stops when the ice storage bin is full.



If you don't want to use the automatic icemaker, turn the icemaker switch to OFF.If you want to use automatic icemaker again, change the switch to ON.

Automatic

icemaker

•

It is normal that a noise is produced when ice drops into the ice storage bin.

NOTE

•

Do not insert your hands in to the Icemaker in operation. It may cause to injure you.

Power Switch

Feeler Arm

•

Reference : Hold your cup in place for a couple of seconds after dispensing ice or water so

the last few drops go in to your cup instead of the floor.

Dispenser use



Select among crushed ice, water, and cubed ice and press the push switch with a glass or other container.

After dispenser

is used

The water collector has no self-drainage function, so it should be cleaned regularly. Remove the cover by pulling the front of the water collector cover and dry it with a cloth.

Water

Light the water lamp by pressing the selection button.

Crushed Ice

Light the crushed ice lamp by pressing the selection button.

Cubed Ice

Light the cubed ice lamp by pressing the selection button.

WARNING

Operation

Ice is lumped together



When ice is lumped together, take the ice lumps out of the ice storage bin, break them into small pieces, and then place them into the ice storage bin again.



When the ice maker produces too small or lumped together ice, the amount of water supplied to the ice maker need to adjusted. Contact the service center.

❈ If ice is not used frequently, it may lump together.

Power failure



Ice may drop into the freezer compartment. Take the ice storage bin out and discard all the ice then dry it and place it back. After the machine is powered again, crushed ice will be automatically selected.

The unit is newly installed



It takes about 12 hours for a newly installed refrigerator to make ice in the freezer compartment.

When ice maker

does not operate

smoothly

Please select this function for prompt freezer.



OFF➝ ON➝ OFF is repeated whenever pressing button.



The arrow mark graphic remains at the On status after flickering 4 times when selecting Special Refrigeration On.



Prompt freezer function automatically turns off after a fixed time passes.

Express freezer

On Off

Hold the ice maker cover with both hands and pull it toward you while pressing the button on part (1).

How to

disassemble the

automatic

icemaker

- Do not disassemble the ice maker unless it is necessary.

- Hold the ice storage bin using both hands so that it does not fall.

- Do not touch the ice dispenser with your hand or tool.

- Because the ice maker can operate by opening the freezer door, please take precaution.

- When you want to use the ice bucket space as the storage space, make sure to use it by turning off the ice maker after removing the ice bucket.

WARNING

Operation

This button stops operation of different button.



Locking or Release is repeated whenever the is pressed more than 3 seconds.



If you use the button, none of the other buttons will work until you unlock them.

Lock

LOCK

UNLOCK



There is a replacement indicator light for the water filter cartridge on the dispenser.



The water filter should be replaced every six months.



The filter light comes on to let you know when to replace filter.



After replacing the filter, press and hold the filter button more than 3 seconds to reset the indicator.

Filter condition

(filter replacement

cycle) display

function

Dispenser light

This button turn the dispenser light in the dispenser on an off.



The dispenser light function is turned ON or OFF by pressing button.

On Off

The other

functions

Door open warning



3 times of warning sounds at the interval of 30 seconds if a minute passes with the door of refrigerator and the hombar door opened or completely closed.



Please contact with the local service center if warning continue to sound even after closing the door.

Diagnosis (failure detection) function



Diagnosis function automatically detects failure when failure is found in product during the use of refrigerator.



If failure occurs at product, it does not operate though pressing any button and normal indication is not done. In this case, do not turn power off but immediately contact with the local service center. A lot of time are need for service engineer to detect the failed part if turning it off.

Operation

Throw away the ice (about 20 pieces) and water (about 7 glasses) first made after refrigerator installation.

The first ice and water may include particles or odor from the feed water pipe or feed water box. This is necessary in case that the refrigerator has not been used for a long time.

Keep children away from the dispenser.

Children may push switch incorrectly bad or damage lamps.

Be careful that food is not block the ice passage.

If foods are placed at the entrance of ice passage, ice may not be dispensed. The ice passage may also be covered with ice powder if splinter ice is used only. This time, remove the ice powder accumulated.

Never store beverage cans or other foods in ice storage bin for the purpose of rapid cooling.

Such actions may damage the automatic ice maker.

Never use thin crystal glass or crockery to collect ice.

Such glasses or containers may be broken.

Put ice first into a glass before filling water or other beverages.

Water may be splashed if ice is added to existing liquid in a glass.

Never touch a hand or other tools on ice outlet.

Touch may cause a part breakage or hand injury.

Never remove the ice maker cover.

Sometimes level the surface so that the ice storage bin is fully filled with ice.

Ice is piled up just near the ice maker. So, such status may be considered, by the ice maker, that the ice storage bin is fully filled and ice making operation may stop.

If discolored ice is dispensed, immediately contact service center, stopping use.

Never use too narrow or deep glass.

Ice may be jammed in ice passage and, thus, the refrigerator may be failed.

Keep the glass at a proper distance from ice outlet.

A glass too close to the outlet may hinder ice from coming out.

Water is cooled while stored in the water tank in the refrigerator compartment, and then sent to the dispenser. Ice is made in the automatic ice maker and sent to the dispenser divided into crushed or cubed form ice.

How ice/cold

water is supplied

•

It is normal that the water is not very cold at first. If you want colder water, add ice into the glass.

NOTE

CAUTION

Operation

Refreshment center

You can use the can server on the top and side to arrange and store the cans.

1. Pull down the handle when you want to store

the cans.

2. If you do not want to use the can server, fixate

the can server on the top so that you can utilize the space of Home Bar more effectively.

* When you press both sides of the bottom part of

the cover on the main unit of the fridge and freezer Home Bar, it will be fixated to prevent the food inside the Home Bar from falling into the fridge or freezer.

How to use the

can server

First separate the upper door basket of the Home Bar (1) and then pull up the Home Bar cover(2).

How to disassemble the fridge Home Bar

cover

1. Do not use the refrigerator with the internal Home Bar cover taken out.

- If the cover is taken out, the Home Bar function cannot work.

2. Be careful not to press or damage the Home Bar support board.

- If you lean or press the support board with your arm, it can be damaged.

- Do not use the support board as a cutting board or use sharp tools on the support board to prevent any scratches.

- When the support board is wet with alien fluid such as juice, it may not operate properly.

- When the packing part is wet with alien fluid such as juice, periodically wipe the part.

Precaution

1. Press the top central part of the Home Bar until you hear the "Click" sound.

- You can save electricity because you do not have to open the refrigerator door.

- Because the indoor lamps of the fridge and freezer are turned on even when you open only the Home Bar door, you can easily take out the food you want.

- When closing the Home Bar, press until you hear the "Click" sound.

2. Open the door and use the door as the support board.

- Put the beverage or food on the support board for convenience of use.

How to use the

Home Bar

Press until you hear the "Click" sound

Operation

Shelf

You can store side dish or refrigerated food on the shelf with sufficient space in between the containers.

How to use

1. Hold the front part of the shelf and pull it out until it gets blocked by the hooking part.

2. When you cannot pull out the shelf any more, lift it up slightly.

3. While holding the shelf slightly, tilt the shelf to pull it out.

How to

disassemble

Egg box

•

Never use the egg box as an ice storage bin. It can be broken.

•

Never store the egg box in the freezer compartment or fresh compartment.

NOTE

[Type-1] [Type-2]

You can move the egg box to wherever you want.

Operation

Nano charcoal deodorizer

With the Nano charcoal deodorizer system, you can deodorize the refrigerator and the deodorizer can be reused.

How to use

Use the (-) driver on the bottom grooved part of the deodorizer cover to separate it while pushing to the front side.

 How to reuse the deodorizer

You can reuse the deodorizer continuously by drying it well with the hair dryer.

How to

disassemble

LED lamp (Freezer/Fridge)

1. LED operation within the fridge

- The indoor LED lamp inside the refrigerator will be turned on

when you open the freezer/fridge door.

* The LED lamp will be turned on when you open the freezer/fridge or

Home Bar door.

* The LED lamp can be used semi-permanently.

2. LED operation on the refrigerator door

(Applicable to model with external LED lamp)

- The ON/OFF switch of the door LED lamp is located on

the top part of the refrigerator and you can see the switch when you open the refrigerator door.

- When the door LED lamp is turned ON (Fig. 1),

the LED on the front door will stay on. (There is no issue with the life span of the LED lamp even when it is kept on continuously.)

- When the door LED lamp is turned OFF (Fig. 2),

the LED will be turned on only when the door is opened (Including H/Bar door), and will automatically be turned off 1 minute after the door is closed.

* If the part where door LED lamp is installed is impacted, it may cause a problem

to the door LED lamp.

* The door LED will be completely turned on 8 seconds after the power is initially

supplied, and will immediately be turned off when the power supply is disconnected during this time.

How to use

<Fig. 1>

<Fig. 2>

Operation

Fresh compartment

You can store fruits or vegetables.

How to use

1. Hold the front handle of the fresh compartment and pull it out until it gets blocked by the hooking part.

2. When you cannot pull out the fresh compartment any more, lift it up slightly to pull it out completely to the front side (outer side).

* The fresh compartment can be reassembled in the

reverse order.

How to

disassemble the

upper fresh

compartment

 When pulling out the lower fresh compartment

1. Hold the front handle of the fresh compartment and pull it forward.

2. When you cannot pull out the fresh compartment any more, lift it up slightly to pull it out to the front side.

How to

disassemble the

lower fresh

compartment

Hold the cover with both hands and pull it out.

* When disassembling the cover, always

disassemble the fresh compartment first.

How to

disassemble

upper/lower fresh

compartment

cover

 When inserting the lower fresh compartment

* When inserting the fresh compartment, always lift the cover

up to push it in.

- Always disassemble the fresh compartment using two hands. You can be injured from the weight of the compartment when filled with food.

- When disassembling/reassembling the fresh compartment of the fridge, open the refrigerator door fully.

WARNING

+ 58 hidden pages