LG GR-P227-STQA User Manual

2
Entry
Important safety instruction
Identification of parts
Where to install
Door removal
Door replacement
Feed water pipe installation
Starting
Adjusting the temperatures and functions
Refreshment center (Applicable to some models only)
Shelf (Applicable to some models only)
Wine holder (Applicable to some models only)
Egg box (Applicable to some models only)
Humidity control in the vegetable compartment
Convert into a vegetable or meat compartment (Applicable to some models only)
Deodorizer (Applicable to some models only)
Miracle Zone Temperature Transition Corner (Applicable to some models only)
Temperature Change at Miracle Zone (Applicable to some models only)
Miracle Zone (Applicable to some models only)
Location of foods
Storing foods
How to dismantle parts
General information
Cleaning
Trouble shooting
Table of contents
Introduction
Installation
Operation
Suggestion on
food storage
Care and
maintenance
3
3
4
5
6
7
7
8
9
9
14
15
15
15
16
16
16
17
17
17
18
19
20
22
22
23
Entry
The model and serial numbers are found on the inner case or back of refrigerator compartment of this unit. These numbers are unique to this unit and not available to others. You should record requested information here and retain this guide as a permanent record of your purchase. Staple your receipt here.
Date of purchase : Dealer purchased from : Dealer address : Dealer phone no. : Model no. : Serial no. :
Before it is used, this refrigerator must be properly installed and located in accordance with the installation instructions in this document.
Never unplug your refrigerator by pulling on the power cord. Always grip plug firmly and pull it straight out from the outlet.
When moving your appliance away from the wall, be careful not to roll over the power cord or to damage it in any way.
After your refrigerator is in operation, do not touch the cold surfaces in the freezer compartment
, particularly when your hands are damp or wet. Skin could adhere to
these extremely cold surfaces. Unplug the power cord from the power outlet for cleaning or other requirements. Never
touch it with wet hands because you can get an electric shock or be hurt. Never damage, process, severely bend, pull out, or twist the power cord because
damage the powercord may cause a fire or electric shock. You have doubts on whether the appliance is properly grounded.
Never place glass products in the freezer because they may be broken due to expansion when their contents are frozen.
Never allow your hands within the ice storage bin of the automatic ice maker. You could be hurt by the operation of the automatic ice maker.
The appliance is not intended for use by young children or infirm persons without supervision.
Young children should be supervised to ensure that they do not play with the appliance. Never allow anyone to climb, sit, stand or hang on the refreshment center door. These
actions may damage the refrigerator and even tip it over, causing severe personal injury. If possible, connect the refrigerator to its own individual electrical outlet to prevent it and
other appliances or household lights from causing an overload that could cause a power outage.
The refrigerator-freezer should be so positioned that the supply plug is accessible for quick disconnection when accident happens.
If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.
Do not modify or extend the Power Cord length.
It will cause electric shock or fire.
Introduction
3
Important safety instruction
Don’t use an
extension cord
Accessibility of
Supply Plug
Supply Cord
Replacement
Warning
4
Introduction
Identification of parts
DANGER: Risk of child entrapment. Before you throw away your old refrigerator or freezer: Take off the doors but leave the shelves in place so that children may not easily climb inside. The appliance is not intended for use by young children or infirm persons without supervision. Young children should be supervised to ensure that they do not play with the appliance.
Don’t store or use gasoline or other flammable vapor and liquids in the vicinity of this or any other appliance.
In the event of an electric short circuit, grounding (earthing) reduces the risk of electric shock by providing an escape wire for the electric current. In order to prevent possible electric shock, this appliance must be grounded improper use of the grounding plug can result in an electric shock. Consult a qualified electrician or service person if the grounding instructions are not completely understood, or if you have doubts on whether the appliance is properly grounded.
Child entrapment
warning
Don’t store
Grounding (Earthing)
If you found some parts missing from your unit, they may be parts only used in other models. (i.c. the “Refreshment center” is not included in all models)
NOTE
Freezer compartment
Refrigerator compartment
Milk product corner
Lamp
Automatic
ice maker
Shelf
Shelf
Door rack
Drawer
Drawer
Door rack
Lower cover
Lamp
Door rack
Door rack
Can Server
(Optional)
Shelf
Shelf (Folding or Normal)
Refreshment center (Optional)
Egg box
Vegetable drawer
Miracle Zone (Optional) Fresh compartment (Optional)
Conversion switch (Meats/Vegetables) (Optional)
Humidity switch
Wine holder (Plastic or wire)
5
Select a good
location
Where to Install
1. Place your appliance where it is easy to use.
2. Avoid placing the unit near heat sources, direct sunlight or moisture.
5. Don't install the appliance below 5∞C. It may cause affect the performance.
4. To avoid vibrations, the appliance must be leveled.
Disposal of the
old appliance
This appliance contains fluid (refrigerant, lubricant)and is made of parts and materials which are reusable and/or recyclable. All the important materials should be sent to the collection center of waste material and can be reused after rework (recycling). For take back, please contact with the local agency.
Installation
6
Installation
Door removal
Failure to do so could result in death or serious injury.
If your access door is too narrow for the refrigerator to pass through, remove the refrigerator door and pass the refrigerator laterally.
Electric Shock Hazard
Disconnect electrical supply to refrigerator before installing.
Remove the lower cover by lifting upward, and remove clip, and then pull up the feed water tube while pressing area shown in the figure to the right.
Remove lower
cover and
then feed water
tube
Warning
Remove the
freezer
compartment
door
Remove the
refrigerator
door
1) Removing the hinge cover by loosening the screws. Separate all connection wires except for theearth line after.
2) Remove the keeper by rotating it counter clockwise ()and then lifting the upper hinge up(
).
3) Remove the freezer compartment door by lifting it upward. This time, the door should be lifted enough for the feed water pipe tube to be completely pulled out.
1) Loosen the hinge cover screws and remove the cover. Remove connection wire, if any, except for the earth line.
2) Remove keeper by rotating it clockwise () and then remove the upper hinge by lifting it up ().
3) Remove the refrigerator compartment door by lifting it up.
If a tube end is deformed or abraded, cut the part away.
NOTE
When removing the upper hinge, be careful that the door does not fall forwards .
NOTE
Move the refrigerator compartment door passing through the access door and lay it down, but be careful not to damage the feed water pipe tube.
NOTE
Lower cover
Lower hinge
Lower hinge
Keeper
Feed water tube
Connection wires
Hinge cover
Upper hinge
Keeper
Upper hinge
Earth line
Upper hinge
Connection
wires
7
Installation
Door replacement
Feed water pipe installation
Pass the refrigerator laterally through the access door as shown in the right figure.
Automatic ice maker operation needs water pressure of 147~834 kPa (1.5~8.5 kgf/cm2) (That is, an instant paper cup (180 cc) will be fully filled within 3 sec.).
Keep the total length of the feed water pipe tube within 8 m and be careful for the tube not be bent. If the tube is 8 m or longer it may cause trouble in water feed owing to the drain water pressure.
Install the feed water pipe tube at a place free from heat.
Connect to potable water supply only.
Refer to instructions with water filter kit for installation.
Mount them in the reverse sequence of removal after they pass through the access door.
Pass the
refrigerator
Before
installation
Warning
1
2
3
4
5
M a x
F
R Z
T
E M P R E F T E M P
M i n
5
4
3
2
1
M a x
8
Installation
Height adjustment
Level the door by inserting flat(-type) driver into the groove of the left height adjusting screw and rotate it clockwise ().
Level the doorby inserting flat (-type) driver into the groove of the right height adjusting screw and rotate it clockwise ().
The refrigerator doors will close smoothly by heightening the front side by adjusting the height adjusting screw. If the doors do not close correctly, performance may be affected.
If the freezer
compartment door
is lower than the
refrigerator
compartment door
If the freezer
compartment door
is higher than the
refrigerator
compartment door
After leveling the
door height
Next
1. Wipe off all dust accumulated during shipping and clean your appliance thoroughly.
2. Install accessories such as the ice cube box, cover evaporating tray, etc., in their proper places. They are packed together to prevent possible damage during shipping.
3. Connect the power supply cord (or plug) to the outlet. Don't double up with other appliances on the same outlet.
9
Starting
When your refrigerator is first installed, allow it to stabilize at normal operating temperatures for 2-3 hours prior to filling it with fresh or frozen foods. If operation is interrupted, wait 5 minutes before restarting.
Adjusting the temperatures and functions
Operation
Your model may not include every option.
The control display is operated by touch. Excessive moisture on the display may cause a malfunction. Please keep display clean and dry.
NOTE
10
Operation
You can adjust temperature of and freezer room and refrigerator room.
Whenever pressing button, setting is repeated in the order of (Weak)
(Middle Weak) (Middle)(Middle Strong)(Strong).
The actual inner temperature varies depending on the food status, as the indicated setting temperature is a target temperature, not actual temperature within refrigerator.
Refrigeration function is weak in the initial time. Please adjust temperature as above after using refrigerator for minimum 2~3 days.
How to adjust the
temperature in
the freezer
compartment
How to adjust the
temperature in
the refrigerator
compartment
Display Power Saving Mode
This function places the display into power saving mode until the next time the door is opened. Press the FREEZER and EXPRESS FRZ. buttons simultaneously and hold them for 5 seconds until the Ding sounds. All LEDs will then turn ON, then OFF. When the power saving mode is activated, the display will remain off until the next time the door is opened. Then, it will come on whenever a door is opened or a button is pressed and remain on for 20 seconds after the last door opening or button selection. To deactivate the power saving mode, press the FREEZER and EXPRESS FRZ. buttons simultaneously and hold them for 5 seconds until the Ding sounds.
11
Operation
How to use
dispenser
Select one among crushed ice, water, and cubed ice and slightly press the push switch with a glass or other container.
Crushed ice
Light the crushed ice indicating lamp by pressing the selection button.
C
rushed
ice will be
dispensed by pressing the
push switch with a glass.
Water
Light the water indicating lamp by pressing the selection button.
Water will be dispensed by pressing the push switch with a glass.
Cubed ice
Light the cubed ice indicating lamp by pressing the selection button.
Cubed ice will be dispensed by pressing the push switch with a glass.
Reference : Hold your cup in place for a couple of seconds after dispensing ice or water so
the last few drops go in to your cup instead of the floor.
The automatic icemaker can automatically make 6 cubes at a time, 70~120 pieces per day. This quantity may vary by circumstance, including ambient temperature, door opening, freezer load. etc.
Icemaking stops when the ice storage bin is full.
If you don't want to use the automatic icemaker, turn the icemaker switch to OFF. If you want to use automatic icemaker again, change the switch to ON.
The water amount will vary depending on the water amount selection button. Setting, as well as the water pressure of the connected water line.
Automatic
icemaker
It is normal that a noise is produced when ice drops into the ice storage bin.
NOTE
Water Amount Indicator Light
Power Switch
Water Amount Selection Button
Feeler Arm
Operation
12
Ice is lumped together
When ice is lumped together, take the ice lumps out of the ice storage bin, break them into small pieces, and then place them into the ice storage bin again.
When the ice maker produces too small or lumped together ice, the amount of water supplied to the ice maker need to adjusted. Contact the service center.
If ice is not used frequently, it may lump together.
Power failure
Ice may drop into the freezer compartment. Take the ice storage bin out and discard all the ice then dry it and place it back. After the machine is powered again, crushed ice will be automatically selected.
The unit is newly installed
It takes about 12 hours for a newly installed refrigerator to make ice in the freezer compartment.
When ice maker
does not operate
smoothly
Please select this function for prompt freezer.
OFFONOFF is repeated whenever pressing button.
The arrow mark graphic remains at the On status after flickering 4 times when selecting Special Refrigeration On.
Prompt freezer function automatically turns off after a fixed time passes.
Express freezer
This button stops operation of different button.

Locking or Release is repeated whenever the is pressed more than 3 seconds.

If you use the ALARM/LOCK button, none of the other buttons will work until you unlock them.
Lock
Door alarm
Door open warning
A warning tone will sound 3 times at thirty-second intervals if the refrigerator or freezer door is left open for more than sixty seconds.
Please contact with the local service center if warning continue to sound even after closing the door.

There is a replacement indicator light for the water filter cartridge on the dispenser.

The water filter should be replaced every six months.

The filter light comes on to let you know when to replace filter.

After replacing the filter, press and hold the filter button more than 3 seconds to reset the indicator.
Filter condition
(filter replacement
cycle) display
function
Dispenser light
This button turn the dispenser light in the dispenser on an off.

The dispenser light function is turned ON or OFF by pressing Light/Filter button.
On Off
Operation
13
Throw away the ice (about 20 pieces) and water (about 7 glasses) first made after refrigerator installation.
The first ice and water may include particles or odor from the feed water pipe or feed water box. This is necessary in case that the refrigerator has not been used for a long time.
Keep children away from the dispenser.
Children may push switch incorrectly bad or damage lamps.
Be careful that food is not block the ice passage.
If foods are placed at the entrance of ice passage, ice may not be dispensed. The ice passage may also be covered with ice powder if splinter ice is used only. This time, remove the ice powder accumulated.
Never store beverage cans or other foods in ice storage bin for the purpose of rapid cooling.
Such actions may damage the automatic ice maker.
Never use thin crystal glass or crockery to collect ice.
Such glasses or containers may be broken.
Put ice first into a glass before filling water or other beverages.
Water may be splashed if ice is added to existing liquid in a glass.
Never touch a hand or other tools on ice outlet.
Touch may cause a part breakage or hand injury.
Never remove the ice maker cover. Sometimes level the surface so that the ice storage bin is fully filled with ice.
Ice is piled up just near the ice maker. So, such status may be considered, by the ice maker, that the ice storage bin is fully filled and ice making operation may stop.
If discolored ice is dispensed, immediately contact service center, stopping use. Never use too narrow or deep glass.
Ice may be jammed in ice passage and, thus, the refrigerator may be failed.
Keep the glass at a proper distance from ice outlet.
A glass too close to the outlet may hinder ice from coming out.
Cautions
The other functions
Ambient Temperature Display Window.

Temperature is displayed only between -9C ~ 49∞C.

Temperature less than -9Cis indicated with LO and temperature more than 49Cis indicated with HI.
Diagnosis (failure detection) function
Diagnosis function automatically detects failure when failure is found in product during the use of refrigerator.
If failure occurs at product, it does not operate though pressing any button and normal indication is not done. In this case, do not turn power off but immediately contact with the local service center. A lot of time are need for service engineer to detect the failed part if turning it off.
Water is cooled while stored in the water tank in the refrigerator compartment, and then sent to the dispenser. Ice is made in the automatic ice maker and sent to the dispenser divided into crushed or cubed form ice.
How ice/cold
water is supplied
It is normal that the water is not very cold at first. If you want colder water, add ice into the glass.
NOTE
14
Operation
Refreshment center (Applicable to some models only)
Open the refreshment center door.
You can access the refreshment center without opening refrigerator door and thus saving electricity.
Inner lamp is lit in refrigerator compartment when the refreshment center door opens. Thus it is easy to identify the contents.
Never use the refreshment centerdoor as a choppingboard and take care not to damage it with sharp tools.
Never rest your arms or severely press on it.
The
refreshment center
can not function
normally without the cover.
Not only can the refreshment centerdoor may be damaged, but also children may be hurt.
How to use
Never place
heavy items on
the refreshment
center door or
allow children to
hang it on.
Never take out
the inner
refreshment
center cover
Use the
refreshment
center door as a
stand
15
Operation
Egg box (Applicable to some models only)
Never use the egg box as an ice storage bin. It can be broken.
Never store the egg box in the freezer compartment or fresh compartment.
NOTE
Shelf (Applicable to some models only)
Wine holder (Applicable to some models only)
You can store taller items such as a gallon container or bottles by simply pushing in front half of shelf underneath back half of shelf. Pull toward you to return to a full shelf.
Folding Shelf
In case of inserting the wine holder :
Pull the wine holder downward as in
after inserting it into the side anchoring part of the shelf as in by catching it upward as in .
In case of separating the wine holder :
Pull the wine holder inward as in after holding it upward as in by catching it.
Bottles can be stored laterally with this wine corner. This can be attached to any shelf.
Wine holder
adjustment
(Type 1)
(Type 2)
=6[RG? =6[RG?
You can move the egg box to wherever you want.
Bottles can be stored laterally with this wine rack.
16
Operation
Humidity control in the vegetable compartment
The humidity can be controlled by adjusting the humidity control switch to the left/right when storing vegetables or fruits.
HIGH LOW
HUMIDITY CONTROL
HIGH LOW
HUMIDITY CONTROL
High humidity
Low humidity
Convert into a vegetable or meat compartment (Applicable to some models only)
The
meat
compartment maintains the temperature at a lower point than the
refrigerator compartment so that meat or fish can be stored fresh longer.
The bottom drawer in the refrigerator can be converted into a vegetable or meat compartment
Vegetables or fruits are frozen if the conversion switch is set to meats
compartment. So, be sure to check it before storing foods.
NOTE
Deodorizer (Applicable to some models only)
This system efficiently absorbs strong odors by using the optical catalyst. This system does hot have any affect on stored food.
Since it is installed already installed onto the cool air intake duct from the from the refrigerator compartment, you need no separate installation.
Please use closed containers to store food with pungent odors.
Otherwise, this oder can be absorbed by other food in the compartment.
How to use the
deodorizing
system
Operation
17
Miracle Zone Temperature Transition Corner (Applicable to some models only)
Miracle Zone (Applicable to some models only)
By pressing the button, store vegetables, fruits or other types of food such as meat to be defrosted, raw fish, etc.
Temperature Change at Miracle Zone (Applicable to some models only)
You can select optimum temperature range depending on types of foods stored.
- 3-step of temperature selection
including -3°C, -1°C and 4°C is available. Vegetables/fruits and cold storage foods requiring humidity maintenance and meats/fishes can be more freshly stored depending on type of foods stored.
First, remove the vegetable bin.
After lifting the Miracle Zone case slightly , reach inside and pull it outward .
When using the Miracle Zone as storage room of meats, storing vegetables or fruits may be frozen
When using the Miracle Zone as storage room of meats, keeping meats or fishes may be spoiled and thus meats or fishes must be kept at the F-room.
If opening a door of the R-room, lamp turns on in the selected status and lamp turns off if closing it.
(Vegetable/Fruit)(Cold storage while maintaining humidity)(Meat) is sequentially repeated whenever pressing the "Selection" button.
When removing
Miracle Zone
Method to Use
Fit the Miracle Zone case on to the ledge and gently slide it in .
When forced, the connecting parts can be damaged.
When installing
Miracle Zone
Loading...
+ 37 hidden pages