Lg GR-P227STJA User Manual

CHLADNIKA
Nvod na obsluhu
Tento nvod si, prosm, pred pouìitm chladniky dkladne pretajte a uchovvajte ho pre prpad potreby na dostupnom mieste.
2
Entry
Important safety instruction
Where to install
Door removal
Door replacement
Feed water pipe installation
Height adjustment
Starting
Adjusting the temperatures and functions
Refreshment center (Applicable to some models only)
Shelf (Applicable to some models only)
Wine holder (Applicable to some models only)
Egg box (Applicable to some models only)
Humidity control in the vegetable compartment
Convert into a vegetable or meat compartment (Applicable to some models only)
Deodorizer (Applicable to some models only)
Miracle Zone Temperature Transition Corner (Applicable to some models only)
Temperature Change at Miracle Zone (Applicable to some models only)
Miracle Zone (Applicable to some models only)
Location of foods
Storing foods
How to dismantle parts
General information
Cleaning
Trouble shooting
Table of contents
Introduction
Installation
Operation
Suggestion on
food storage
Care and
maintenance
3
3
4
5
6
7
7
8
9
9
14
15
15
15
16
16
16
17
17
17
18
19
20
22
22
23
Entry
The model and serial numbers are found on the inner case or back of refrigerator compartment of this unit. These numbers are unique to this unit and not available to others. You should record requested information here and retain this guide as a permanent record of your purchase. Staple your receipt here.
Date of purchase : Dealer purchased from : Dealer address : Dealer phone no. : Model no. : Serial no. :
Before it is used, this refrigerator must be properly installed and located in accordance with the installation instructions in this document.
Never unplug your refrigerator by pulling on the power cord. Always grip plug firmly and pull it straight out from the outlet.
When moving your appliance away from the wall, be careful not to roll over the power cord or to damage it in any way.
After your refrigerator is in operation, do not touch the cold surfaces in the freezer compartment
, particularly when your hands are damp or wet. Skin could adhere to
these extremely cold surfaces. Unplug the power cord from the power outlet for cleaning or other requirements. Never
touch it with wet hands because you can get an electric shock or be hurt. Never damage, process, severely bend, pull out, or twist the power cord because
damage the power cord may cause a fire or electric shock. You have doubts on whether the appliance is properly grounded.
Never place glass products in the freezer because they may be broken due to expansion when their contents are frozen.
Never allow your hands within the ice storage bin of the automatic ice maker. You could be hurt by the operation of the automatic ice maker.
The appliance is not intended for use by young children or infirm persons without supervision.
Young children should be supervised to ensure that they do not play with the appliance. Never allow anyone to climb, sit, stand or hang on the refreshment center door. These
actions may damage the refrigerator and even tip it over, causing severe personal injury. If possible, connect the refrigerator to its own individual electrical outlet to prevent it and
other appliances or household lights from causing an overload that could cause a power outage.
The refrigerator-freezer should be so positioned that the supply plug is accessible for quick disconnection when accident happens.
If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.
Do not modify or extend the Power Cord length.
It will cause electric shock or fire.
Introduction
3
Important safety instruction
Don’t use an
extension cord
Accessibility of
Supply Plug
Supply Cord
Replacement
Warning
4
Introduction
DANGER: Risk of child entrapment. Before you throw away your old refrigerator or freezer: Take off the doors but leave the shelves in place so that children may not easily climb inside. The appliance is not intended for use by young children or infirm persons without supervision. Young children should be supervised to ensure that they do not play with the appliance.
Don’t store or use gasoline or other flammable vapor and liquids in the vicinity of this or any other appliance.
In the event of an electric short circuit, grounding (earthing) reduces the risk of electric shock by providing an escape wire for the electric current. In order to prevent possible electric shock, this appliance must be grounded improper use of the grounding plug can result in an electric shock. Consult a qualified electrician or service person if the grounding instructions are not completely understood, or if you have doubts on whether the appliance is properly grounded.
Child entrapment
warning
Don’t store
Grounding (Earthing)
Identification of parts
Parts, features, and options vary by model. Your model may not include every option.
NOTE
Freezer Compartment
Refrigerator Compartment
Milk product corner
Lamp
Lamp
Automatic
Icemaker
Shelf
Shelf
Door Rack
Drawer
Drawer
Door Rack
Lower Cover
Shelf
Refreshment center (Optional)
Can Server
(Optional)
Shelf (Folding or Normal)
Wine holder (Plastic or wire)
Egg Box
Vegetable Drawer
Humidity Switch
Door Rack
Door Rack
Miracle Zone (Optional) Fresh compartment (Optional)
Conversion switch (Meats/Vegetables) (Optional)
5
Select a good
location
Where to Install
1. Place your appliance where it is easy to use.
2. Avoid placing the unit near heat sources, direct sunlight or moisture.
3. Air must circulate properly around your appliance to ensure efficient operation. If your appliance is placed in a recessed area in the wall, allow at least a 12 Inches (30 cm) or greater clearance above the appliance and 2 inches (5 cm) or more from the wall. The appliance should be elevated 1 inch (2.5 cm) from the floor, especially if it is carpeted.
5. Don't install the appliance below 5∞C. It may cause affect the performance.
4. To avoid vibrations, the appliance must be leveled.
Disposal of the
old appliance
This appliance contains fluid (refrigerant, lubricant)and is made of parts and materials which are reusable and/or recyclable. All the important materials should be sent to the collection center of waste material and can be reused after rework (recycling). For take back, please contact with the local agency.
Installation
6
Installation
Door removal
Failure to do so could result in death or serious injury.
If your access door is too narrow for the refrigerator to pass through, remove the refrigerator door and pass the refrigerator laterally.
Electric Shock Hazard
Disconnect electrical supply to refrigerator before installing.
Remove the lower cover by lifting upward, and remove clip, and then pull up the feed water tube while pressing area shown in the figure to the right.
Remove lower
cover and
then feed water
tube
Warning
Remove the
freezer
compartment
door
Remove the
refrigerator
door
1) Removing the hinge cover by loosening the screws. Separate all connection wires except for the earth line after.
2) Remove the keeper by rotating it counter clockwise (
)
and then lifting the upper
hinge up(
).
3) Remove the freezer compartment door by lifting it upward. This time, the door should be lifted enough for the feed water pipe tube to be completely pulled out.
1) Loosen the hinge cover screws and remove the cover. Remove connection wire, if any, except for the earth line.
2) Remove keeper by rotating it clockwise () and then remove the upper hinge by lifting it up ().
3) Remove the refrigerator compartment door by lifting it up.
If a tube end is deformed or abraded, cut the part away.
NOTE
When removing the upper hinge, be careful that the door does not fall forwards .
NOTE
Move the refrigerator compartment door passing through the access door and lay it down, but be careful not to damage the feed water pipe tube.
NOTE
Lower cover
Lower hinge
Lower hinge
Keeper
Feed water tube
Connection wires
Hinge cover
Upper hinge
Keeper
Upper hinge
Earth line
Upper hinge
Connection
wires
7
Installation
Door replacement
Feed water pipe installation
Pass the refrigerator laterally through the access door as shown in the right figure.
Automatic ice maker operation needs water pressure of 147~834 kPa (1.5~8.5 kgf/cm2) (That is, an instant paper cup (180 cc) will be fully filled within 3 sec.).
If water pressure does not reach the rating 147 kPa (1.5 kgf/cm2) or below, it is necessary to purchase a separate pressure pump for normal automatic icing and cool water feed.
Keep the total length of the feed water pipe tube within 8 m and be careful for the tube not be bent. If the tube is 8 m or longer it may cause trouble in water feed owing to the drain water pressure.
Install the feed water pipe tube at a place free from heat.
Connect to potable water supply only.
Refer to instructions with water filter kit for installation.
Mount them in the reverse sequence of removal after they pass through the access door.
Pass the
refrigerator
Before
installation
Warning
1
2
3
4
5
M a x
F
R Z
T
E M P R E F T E M P
M i n
5
43
2
1
M a x
8
Installation
Height adjustment
Level the door by inserting flat (-type) driver into the groove of the left height adjusting screw and rotate it clockwise ().
Level the door by inserting flat (-type) driver into the groove of the right height adjusting screw and rotate it clockwise ().
The refrigerator doors will close smoothly by heightening the front side by adjusting the height adjusting screw. If the doors do not close correctly, performance may be affected.
If the freezer
compartment door
is lower than the
refrigerator
compartment door
If the freezer
compartment door
is higher than the
refrigerator
compartment door
After leveling the
door height
Next
1. Wipe off all dust accumulated during shipping and clean your appliance thoroughly.
2. Install accessories such as the ice cube box, cover evaporating tray, etc., in their proper places. They are packed together to prevent possible damage during shipping.
3. Connect the power supply cord (or plug) to the outlet. Don't double up with other appliances on the same outlet.
9
Starting
When your refrigerator is first installed, allow it to stabilize at normal operating temperatures for 2-3 hours prior to filling it with fresh or frozen foods. If operation is interrupted, wait 5 minutes before restarting.
Adjusting the temperatures and functions
Operation
Your model may not include every option.
The control display is operated by touch. Excessive moisture on the display may cause a malfunction. Please keep display clean and dry.
NOTE
10
Operation
Freezer Compartment
temperature adjustment
Setting
temperature
Setting
temperature
Refrigerator Compartment
temperature adjustment
You can adjust temperature of and freezer room and refrigerator room.
Display Power Saving Mode
This function places the display into power saving mode until the next time the door is opened. Press the FREEZER and EXPRESS FRZ. buttons simultaneously and hold them for 5 seconds until the Ding sounds. All LEDs will then turn ON, then OFF. When the power saving mode is activated, the display will remain off until the next time the door is opened. Then, it will come on whenever a door is opened or a button is pressed and remain on for 20 seconds after the last door opening or button selection. To deactivate the power saving mode, press the FREEZER and EXPRESS FRZ. buttons simultaneously and hold them for 5 seconds until the Ding sounds.
Whenever pressing button, setting is repeated in the order of(Weak)
(Middle Weak) ➔(Middle)➔(Middle Strong)➔(Strong).
The actual inner temperature varies depending on the food status, as the indicated setting temperature is a target temperature, not actual temperature within refrigerator.
Refrigeration function is weak in the initial time. Please adjust temperature as above after using refrigerator for minimum 2~3 days.
How to adjust the
temperature in
the freezer
compartment
How to adjust the
temperature in
the refrigerator
compartment
11
Operation
Reference : Hold your cup in place for a couple of seconds after dispensing ice or water so
the last few drops go in to your cup instead of the floor.
How to use
dispenser
Select among crushed ice, water, and cubed ice and press the push switch with a glass or other container.
Water
Light the water lamp by pressing the selection button.
Water will be dispensed by pressing the push switch with a glass.
Crushed Ice
Light the crushed ice lamp by pressing the selection button.
C
rushed ice will be dispensed by pressing the push switch with a glass.
Cubed Ice
Light the cubed ice lamp by pressing the selection button.
Cubed ice will be dispensed by pressing the push switch with a glass.
The automatic icemaker can automatically make 6 cubes at a time, 70~120 pieces per day. This quantity may vary by circumstance, including ambient temperature, door opening, freezer load. etc.
Icemaking stops when the ice storage bin is full.
If you don't want to use the automatic icemaker, turn the icemaker switch to OFF. If you want to use automatic icemaker again, change the switch to ON.
The water amount will vary depending on the water amount selection button. Setting, as well as the water pressure of the connected water line.
Automatic
icemaker
It is normal that a noise is produced when ice drops into the ice storage bin.
NOTE
Water Amount Indicator Light
Power Switch
Water Amount Selection Button
Feeler Arm
Operation
12
Ice is lumped together
When ice is lumped together, take the ice lumps out of the ice storage bin, break them into small pieces, and then place them into the ice storage bin again.
When the ice maker produces too small or lumped together ice, the amount of water supplied to the ice maker need to adjusted. Contact the service center.
If ice is not used frequently, it may lump together.
Power failure
Ice may drop into the freezer compartment. Take the ice storage bin out and discard all the ice then dry it and place it back. After the machine is powered again, crushed ice will be automatically selected.
The unit is newly installed
It takes about 12 hours for a newly installed refrigerator to make ice in the freezer compartment.
When ice maker
does not operate
smoothly
Please select this function for prompt freezer.
OFFONOFF is repeated whenever pressing button.
The arrow mark graphic remains at the On status after flickering 4 times when selecting Special Refrigeration On.
Prompt freezer function automatically turns off after a fixed time passes.
Express freezer
On Off
This button stops operation of different button.
Locking or Release is repeated whenever the is pressed more than 3 seconds.
If you use the ALARM/LOCK button, none of the other buttons will work until you unlock them.
Lock
LOCK
UNLOCK
Door alarm
Door open warning
A warning tone will sound 3 times at thirty-second intervals if the refrigerator or freezer door is left open for more than sixty seconds.
Please contact with the local service center if warning continue to sound even after closing the door.
There is a replacement indicator light for the water filter cartridge on the dispenser.
The water filter should be replaced every six months.
The filter light comes on to let you know when to replace filter.
After replacing the filter, press and hold the filter button more than 3 seconds to reset the indicator.
Filter condition
(filter replacement
cycle) display
function
Dispenser light
This button turn the dispenser light in the dispenser on an off.
The dispenser light function is turned ON or OFF by pressing Light/Filter button.
On Off
Operation
13
Throw away the ice (about 20 pieces) and water (about 7 glasses) first made after refrigerator installation.
The first ice and water may include particles or odor from the feed water pipe or feed water box. This is necessary in case that the refrigerator has not been used for a long time.
Keep children away from the dispenser.
Children may push switch incorrectly bad or damage lamps.
Be careful that food is not block the ice passage.
If foods are placed at the entrance of ice passage, ice may not be dispensed. The ice passage may also be covered with ice powder if splinter ice is used only. This time, remove the ice powder accumulated.
Never store beverage cans or other foods in ice storage bin for the purpose of rapid cooling.
Such actions may damage the automatic ice maker.
Never use thin crystal glass or crockery to collect ice.
Such glasses or containers may be broken.
Put ice first into a glass before filling water or other beverages.
Water may be splashed if ice is added to existing liquid in a glass.
Never touch a hand or other tools on ice outlet.
Touch may cause a part breakage or hand injury.
Never remove the ice maker cover. Sometimes level the surface so that the ice storage bin is fully filled with ice.
Ice is piled up just near the ice maker. So, such status may be considered, by the ice maker, that the ice storage bin is fully filled and ice making operation may stop.
If discolored ice is dispensed, immediately contact service center, stopping use. Never use too narrow or deep glass.
Ice may be jammed in ice passage and, thus, the refrigerator may be failed.
Keep the glass at a proper distance from ice outlet.
A glass too close to the outlet may hinder ice from coming out.
Cautions
Other functions
Ambient Temperature Display Window.
Temperature is displayed only between -9C ~ 49∞C.
Temperature less than -9C is indicated with LO and temperature more than 49C is indicated with HI.
Diagnosis (failure detection) function
Diagnosis function automatically detects failure when failure is found in product during the use of refrigerator.
If failure occurs at product, it does not operate though pressing any button and normal indication is not done. In this case, do not turn power off but immediately contact with the local service center. A lot of time are need for service engineer to detect the failed part if turning it off.
Water is cooled while stored in the water tank in the refrigerator compartment, and then sent to the dispenser. Ice is made in the automatic ice maker and sent to the dispenser divided into crushed or cubed form ice.
How ice/cold
water is supplied
It is normal that the water is not very cold at first. If you want colder water, add ice into the glass.
NOTE
14
Operation
Refreshment center (Applicable to some models only)
Open the refreshment center door.
You can access the refreshment center without opening refrigerator door and thus saving electricity.
Inner lamp is lit in refrigerator compartment when the refreshment center door opens. Thus it is easy to identify the contents.
Never use the refreshment center door as a chopping board and take care not to damage it with sharp tools.
Never rest your arms or severely press on it.
The
refreshment center
can not function
normally without the cover.
Not only can the refreshment center door may be damaged, but also children may be hurt.
How to use
Never place
heavy items on
the refreshment
center door or
allow children to
hang it on.
Never take out
the inner
refreshment
center cover
Use the
refreshment
center door as a
stand
15
Operation
Egg box (Applicable to some models only)
Never use the egg box as an ice storage bin. It can be broken.
Never store the egg box in the freezer compartment or fresh compartment.
NOTE
Shelf (Applicable to some models only)
Wine holder (Applicable to some models only)
You can store taller items such as a gallon container or bottles by simply pushing in front half of shelf underneath back half of shelf. Pull toward you to return to a full shelf.
Folding Shelf
In case of inserting the wine holder :
Pull the wine holder downward as in
after inserting it into the side anchoring part of the shelf as in by catching it upward as in .
In case of separating the wine holder :
Pull the wine holder inward as in ➃after holding it upward as in ➂by catching it.
Bottles can be stored laterally with this wine corner. This can be attached to any shelf.
Wine holder
adjustment
(Type 1)
(Type 2)
3
4
1
2
[Type-1] [Type-2]
You can move the egg box to wherever you want.
Bottles can be stored laterally with this wine rack.
16
Operation
Humidity control in the vegetable compartment
The humidity can be controlled by adjusting the humidity control switch to the left/right when storing vegetables or fruits.
HIGH
LOW
HIGH
LOW
HIGH LOW
HUMIDITY CONTROL
HIGH LOW
HUMIDITY CONTROL
High humidity
Low humidity
Convert into a vegetable or meat compartment (Applicable to some models only)
The
meat
compartment maintains the temperature at a lower point than the
refrigerator compartment so that meat or fish can be stored fresh longer.
The bottom drawer in the refrigerator can be converted into a vegetable or meat compartment
Vegetables or fruits are frozen if the conversion switch is set to meats
compartment. So, be sure to check it before storing foods.
NOTE
Deodorizer (Applicable to some models only)
This system efficiently absorbs strong odors by using the optical catalyst. This system does hot have any affect on stored food.
Since it is installed already installed onto the cool air intake duct from the from the refrigerator compartment, you need no separate installation.
Please use closed containers to store food with pungent odors.
Otherwise, this oder can be absorbed by other food in the compartment.
How to use the
deodorizing
system
Operation
17
Miracle Zone Temperature Transition Corner (Applicable to some models only)
Miracle Zone (Applicable to some models only)
By pressing the button, store vegetables, fruits or other types of food such as meat to be defrosted, raw fish, etc.
Temperature Change at Miracle Zone (Applicable to some models only)
You can select optimum temperature range depending on types of foods stored.
- 3-step of temperature selection
including -3°C, -1°C and 4°C is available. Vegetables/fruits and cold storage foods requiring humidity maintenance and meats/fishes can be more freshly stored depending on type of foods stored.
First, remove the vegetable bin.
After lifting the Miracle Zone case slightly , reach inside and pull it outward  .
When using the Miracle Zone as storage room of meats, storing vegetables or fruits may be frozen
When using the Miracle Zone as storage room of meats, keeping meats or fishes may be spoiled and thus meats or fishes must be kept at the F-room.
If opening a door of the R-room, lamp turns on in the selected status and lamp turns off if closing it.
(Vegetable/Fruit)➔(Cold storage while maintaining humidity)➔(Meat) is sequentially repeated whenever pressing the "Selection" button.
When removing
Miracle Zone
Method to Use
Fit the Miracle Zone case on to the ledge and gently slide it in  .
When forced, the connecting parts can be damaged.
When installing
Miracle Zone
18
Suggestion on food storage
Location of foods
(Refer to identification of parts)
Store wine.
Store small foods such as bread, snacks, etc..
Store various frozen foods such as meat, fish, ice cream, frozen snacks, etc..
Store small packed frozen food.
Temperature is likely to increase as door opens.
So, do not store long-term food such
ice cream, etc..
Wine holder
Snack
drawer
Freezer
compartment
shelf
Freezer
compartment
door rack
Freezer
compartment
drawer
Milk product
corner
Egg box
Refreshment
center
Refrigerator
compartment
shelf
Refrigerator
compartment
door rack
Vegetable drawer
Vegetable
drawer
/meat
drawer
conversion corner
Store meat, fish, chicken, etc.. after wrapping them with thin foil.
Store dry
.
Store milk products such as butter, cheese, etc..
Place this egg box in the proper location.
Store foods of frequent use such as beverage, etc..
Store side dishes or other foods at a proper distance.
Store small packed food or beverages such as milk, juice, beer, etc..
Store vegetables or fruits.
Store vegetable, fruits, meat to thaw, raw fish, etc.. setting the conversion switch as necessary. Be sure to check the conversion switch setting before storing foods.
Suggestion on food storage
19
Storing foods
Store fresh food in the refrigerator compartment. How food is frozen and thawed is an important factor in maintaining its freshness and flavor.
Do not store food which goes bad easily at low temperatures, such as bananas, and melons.
Allow hot food to cool prior to storing, placing hot food in the refrigerator could spoil other food, and lead to higher energy consumption.
When storing the food, cover it with vinyl wrap or store in a container with a lid. This prevents moisture from evaporating, and helps food to keep its taste and nutrients.
Do not block air vents with food. Smooth circulation of chilled air keeps refrigerator temperatures even.
Do not open the door frequently. Opening the door lets warm air enter the refrigerator, and cause temperatures to rise.
Never keep too much food in door rack because they may push against by inner racks so that the door cannot be fully closed.
Do not store bottles in the freezer compartment - they may break when frozen.
Do not refreeze food that has been thawed. This causes loss of taste and nutrient.
When storing frozen food like ice cream for a long period, place it on the freezer shelf, not in the door rack.
Do not touch the cold foods or containers- especially made of metallic -, with wet hands and place glass products in the freezer compartment.
- That’s why you may have chilblains and they may be broken when their inner matters
are frozen, causing personal injury.
Avoid placing moist food in top refrigerator shelves, it could freeze from direct contact with chilled air.
Always clean food prior to refrigeration. Vegetables and fruits should be washed and wiped, and packed food should be wiped, to prevent adjacent food from spoiling.
When storing eggs in their storage rack or box, ensure that they are fresh, and always store them in an upright position, which keeps them fresh longer.
Freezer
compartment
Refrigerator
compartment
If you keep the refrigerator in a hot and humid place, frequent openning of the door
or storing a lot of vegetables in it may cause dew to form which has no effect on its
performance. Remove the dew with dust cloth free from care.
NOTE
20
Care and maintenance
How to dismantle parts
Dismantling is done in the reverse sequence of assembly.
Be sure to unplug the power plug before dismantling and assembly. Never apply severe force to dismantle parts. Parts may be damaged.
NOTE
Freezer
compartment
lamp
Freezer
compartment
shelf
Door rack and
support
Ice storage bin
After dispenser
is used
To remove a shelf, push the shelf to the left , lift the left part of the shelf a bit , lift the right part up , and take it out.
Lift the door rack holding both sides and pull it out .
Hold the ice storage bin as shown in the right figure and pull it out while slightly lifting it .
Do not dismantle the ice storage bin unless it is necessary.
Use both hands to remove the ice bin to avoid dropping it.
The water collector has no self-draining function. It should be cleaned regularly. Remove the cover by pulling the front side of water collector cover and dry it with a cloth.
32
1
1
2
3
Separate the lamp by pulling it out
while slightly
pressing
and rotating
the lamp cover. Turn the bulb counterclockwise. Use a 40-watt bulb (max.) which
can be purchased at a service
center.
1
2
21
Care and maintenance
To remove the lamp cover, press the protrusion under the lamp cover to the front and then pull the lamp cover out. Turn the bulb counterclockwise. Max. 40 W bulb for refrigerator is used and can be purchased at a service center.
Lamp in
refrigerator
compartment
Separate the bin ()to upward.
Separate the upper rack of the refreshment center and then pull out the refreshment center cover
()
.
The refreshment center can be removed by pulling it upwards.
Refreshment
center
To remove the vegetable compartment cover, pull out the vegetable compartment a bit to the front , lift the front part of the vegetable compartment cover as shown by , and take it out.
Vegetable
compartment
cover
1
2
2
1
Be sure to remove parts from the refrigerator door when removing the vegetable compartment,
snack drawer and refreshment center cover.
NOTE
0 0 Suggestion on food storage
22
Care and maintenance
General information
Cleaning
During average length vacations, you will probably find it best to leave the refrigerator in operation. Place freezable items in freezer for longer life. When you plan not to operate, remove all food, disconnect the power cord, clean the interior thoroughly, and leave each door OPEN to prevent odor formation.
Vacation time
Power failure
If you move
Anti
condensation
pipe
Most power failures that are corrected in an hour or two will not affect your refrigerator temperatures. However, you should minimize the number of door openings while the power is off.
Remove or securely fasten down all loose items inside the refrigerator. To avoid damaging the height adjusting screws, turn them all the way into the base.
The outside wall of the refrigerator cabinet may sometimes get warm, especially just after installation. Don’t be alarmed. This is due to the anti-condensation pipe, which pumps hot refrigerator to prevent “sweating” on the outer cabinet wall.
Regular cleaning is recommended. Wash all compartments a baking soda solution or a mild detergent and warm water. Rinse and dry.
Please verify that the power cord is not damaged, power plug is not overheated, or power plug is well inserted into the power consent.
Always remove power cord from the wall outlet prior to cleaning in the vicinity of electrical parts (lamps, switches, controls, etc.). Wipe up excess moisture with a sponge or cloth to prevent water or liquid from getting into any electrical part and causing an electric shock. Never use metallic scouring pads, brushes, coarse abrasive cleaners, strong alkaline solutions, flammable or toxic cleaning liquids on any surface. Do not touch frozen surfaces with wet or damp hands, because damp object will stick or adhere to extremely cold surfaces.
It is important that your refrigerator be kept clean to prevent undesirable odors. Spilled food should be wiped up immediately, since it may acidify and stain plastic surfaces if allowed to settle.
Use a lukewarm solution of mild soap or detergent to clean the durable finish of your refrigerator. Wipe with a clean damp cloth and then dry.
Exterior
Interior
After cleaning
Warning
23
Care and maintenance
Trouble shooting
Before calling for service, review this list. It may save you both time and expense. This list includes common occurrences that are not the result of defective workmanship or materials in this appliance.
Possible cause
Refrigerator control is off.
Refrigerator is in defrost cycle.
Plug at wall outlet is disconnected.
Power outage. Check house lights. Refrigerator is larger than the previous
one you owned. Room or outside weather is hot.
Refrigerator has recently been disconnected for a period of time.
Large amounts of warm or hot food may have been stored recently.
Doors are opened too frequently or too long.
Refrigerator or freezer door may be slightly open.
Refrigerator control is set too cold.
Refrigerator or freezer gasket is dirty, worn, cracked, or poorly fitted.
Thermostat is keeping the refrigerator at a constant temperature.
Solution
Set refrigerator control. See setting the controls.
This is normal for a fully automatic defrosting refrigerator. The defrost cycle occurs periodically.
Make sure plug is tightly pushed into outlet.
Call local electric company. This is normal. Larger, more efficient
units run longer in these conditions. It is normal for the refrigerator to work
longer under these conditions. It takes some hours for the refrigerator
to cool down completely. Warm food will cause the refrigerator to
run longer until the desired temperature is reached.
Warm air entering the refrigerator causes it to run longer. Open the door less often.
Make sure the refrigerator is level. Keep food and containers from blocking door. See problem section. OPENING/CLOSING of doors.
Set the refrigerator control to a warmer setting until the refrigerator temperature is satisfactory.
Clean or change gasket. Leaks in the door seal will cause refrigerator to run longer in order to maintain desired
temperatures.
This is normal. Refrigerator goes on
and
off to keep the temperature constant.
Runing of
refrigerator
Refrigerator compressor
does not run.
Refrigerator
runs too much
or too long
Occurrence
24
Care and maintenance
Refrigerator compressor
does not run.
Occurrence
Temperatures are
too cold
Temperature in the
freezer is too cold but the refrigerator
temperature is
satisfactory.
Temperature in the
refrigerator
is too warm but
the freezer
temperature is
satisfactory.
Temperatures in
the refrigerator
or freezer are
too warm.
Temperatures
are too warm
Meat stored in
fresh meat
drawer freezes.
Food stored in
drawers freezes.
Possible cause
Thermostat is keeping the refrigerator at a constant temperature.
Freezer control is set too cold
Doors are opened too frequently or too long.
Door is slightly open. Large amounts of warm or hot food
may have been stored recently.
Refrigerator has recently been disconnected for a period of time.
Refrigerator control is set too warm.
Refrigerator control is set too warm. Refrigerator control has some effect on freezer temperature.
Freezer control is set too warm.
Refrigerator control is set too cold.
Refrigerator control is set too cold.
Meat should be stored at a temperature just below the freezing point of water
(32˚F,
0˚C) for maximum fresh storage time.
Solution
This is normal. The refrigerator goes on and off to keep the temperature constant.
Set the refrigerator control to a colder setting.
A refrigerator requires some hours to cool down completely.
Wait until the refrigerator or freezer has a chance to reach its selected temperature.
Warm air enters the refrigerator/ freezer whenever the door is opened. Open the door less often.
Set the freezer or refrigerator control to a colder setting until the freezer or refrigerator temperature is satisfactory.
Set the freezer or refrigerator control to a colder setting until the freezer or refrigerator temperature is satisfactory.
It is normal for ice crystals to form due to the moisture content of meat.
Set the refrigerator control to a warmer setting
See above solution.
Set the freezer control to a warmer setting until the freezer temperature is satisfactory.
Close the door completely.
Temperature in the
refrigerator is too
cold and the
freezer
temperature
is satisfactory.
Care and maintenance
25
Sound and noise
Occurrence
Louder sound
levels when
refrigerator is on.
Louder sound
levels when
compressor
comes on.
Moisture collects
on the inside walls
of the refrigerator.
Water/Moisture
/Ice outside
refrigerator
Moisture forms
on the outside of
the refrigerator
or between doors.
Vibrating or
rattling noise.
Water/Moisture
/Ice inside
refrigerator
Possible cause
Today’s refrigerators have increased storage capacity and maintain more even temperatures.
Refrigerator is touching wall or cabinets.
The weather is hot and humid which increases the rate of frost buildup and internal sweating.
Door is slightly open.
Door is opened too often or too long.
Weather is humid.
Door is slightly open,causing cold air from the inside the refrigerator to meet warm air from the outside.
Floor is uneven or weak. Refrigerator rocks on the floor when it is moved slightly.
Refrigerator operates at higher pressures during the start of the ON cycle.
Items placed on the top of the refrigerator are vibrating.
Dishes are vibrating on the shelves in the refrigerator.
Solution
This time, close the door completely.
This is normal in humid weather. When humidity is lower, the moisture should disappear.
See problem section opening/closing of doors.
Move refrigerator so that it does not touch the wall or refrigerator.
This is normal.
It is normal for dishes to vibrate slightly. Move dishes slightly. Make sure refrigerator is level and firmly set on floor.
Be sure floor is level and solid and can adequately support refrigerator.
Remove items.
It is normal for sound levels to be higher.
This is normal. The sound will level off as the refrigerator continues to run.
Open the door less often.
26
Care and maintenance
Odors in refrigerator
Occurrence
Door(s) will not
close.
Door(s) will not
close.
Drawers are
difficult to move.
Dispenser
Dispenser will not
dispense ice
Opening/Closing of
doors/Drawers
Possible cause
Food is touching shelf on top of the drawer
Track that drawer slides on is dirty.
Ice storage bin is empty.
Freezer temperature is set too warm.
Household water line valve is not open.
Refrigerator or freezer door is not
closed.
Refrigerator is not level. It rocks on the floor when it is moved slightly.
Floor is uneven or weak. Refrigerator rocks on the floor when it is moved slightly.
Refrigerator is touching wall or cabinets.
Interior needs to be cleaned.
Food with strong odor is in the refrigerator. Some containers and wrapping materials
produce odors.
Food package is keeping door open.
Door was closed too hard, causing other door to open slightly.
Solution
Be sure both doors are closed.
Open household water line valve and allow sufficient time for ice to be made. When ice is made, dispenser should operate.
Turn the freezer control to a higher setting so that ice cubes will be made. When the first supply of ice is made, the dispenser should operate.
Clean drawer and track.
Be sure floor is level and can adequately support refrigerator. Contact carpenter to correct sagging or sloping floor.
Move refrigerator.
.
Keep less food in drawer.
Adjust the height adjusting screw.
Use a different container or brand of wrapping
materials
.
Move packages that keep door from closing.
Close both doors gently.
Cover food completely.
Clean interior with sponge,warm water and baking soda.
When the first supply of ice is dropped into the bin, the dispenser should operate.
Care and maintenance
27
Dispenser will
not
dispense
ice.
Ice dispenser
is jammed.
Occurrence
Water has an
odd taste
and/or odor.
Dispenser will
not dispense
water.
Possible cause
Water has been in the tank for too long.
Unit not properly connected to cold water line.
This sound is normally made when automatically made ice is dropped into ice storage bin. Volume may vary according to refrigerator’s location.
This sound is normally made when ice maker is supplied with water after dropping the automatically made ice.
Please thoroughly read ‘Automatic ice maker and dispenser’ in this manual.
Ice cubes are frozen together.
Ice has melted and frozen around auger due to infrequent use, temperature fluctuations and/or power outrages.
Ice cubes are jammed between the ice maker arm and back of the bin.
Ice cubes that have been purchased or made in some other way have been used in the dispenser.
Household water line valve is not open. See problem “Ice maker is not making any ice.”
Refrigerator or freezer door is not closed.
Solution
Be sure both doors are closed. Draw and discard 7 glasses of water
to freshen the supply. Draw and discard an additional 7 glasses to completely rinse out tank.
Connect unit to cold water line which supplies water to kitchen faucet.
Open household water line valve.
Use the dispenser often so that cubes do not freeze together.
Only the ice cubes made by the ice maker should be used with the dispenser.
Remove the ice cubes that are jamming the dispenser.
Remove ice storage bin, and thaw and the contents. Clean bin, wipe dry and replace in proper position. When new ice is made, dispenser should operate.
Sound of ice
dropping
Sound of water
supply
Other
DISPOSAL OF YOUR OLD APPLIANCE
1. When this crossed-out wheeled bin symbol is attached to a product it means the product is covered by the European Directive 2002/96/EC.
2.
All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities.
3. The correct disposal of your old appliance will help prevent potential negative consequences for the environment and human health.
4. For more detailed information about disposal of your old appliance, please contact your city office, waste disposal service or the shop where you purchased the product.
Tartalomjegyzék
Feljegyzések Fontos biztonsági elŒírások A hıtŒszekrény kezelŒszervei és egységei
Az alkalmas hely megtatálása Az ajtó leszerelése Az ajtó visszaszerelése A vízvezetékcsŒ beszerelése Magasság beállítása
A hıtŒgép elindítása A hŒmérséklet és egyéb funkciók beállítása Frissentartó rekesz (nem minden modellen) Polcok (nem minden modellen) Borosüveg tartó (nem minden modellen) Tojástartó (nem minden modellen) Páratartalom beállítása a zöldséges fiókban Átalakítás hús- vagy zöldségtároló fiókká (nem minden modellen) A szagtalanító (nem minden modellen) Varázszóna – Változtatható hŒmérsékletı sarok (nem minden modellen) HŒmérséklet-szabályozás a Varázszónában (nem minden modellen) VARÁZSZÓNA (nem minden modellen)
Az élelmiszerek elhelyezése Az élelmiszerek tárolása
Az alkatrészek kiszerelése Általános információk Tisztítás Hibaelhárítás
BevezetŒ
A készülék
felállítása
A hıtŒgép
használata
Javaslatok az
élelmiszerek
tárolásával
kapcsolatban
Ápolás és
karbantartás
29 29 30
31 32 33
33 34
35 35 40 41 41
41 42 42
43 43 43
44
42
48
46
45
48 49
28
Feljegyzések
A készülék típus- és sorozatszámát a hıtŒgép hátoldalán vagy belsejében találja. Ezek az azonosító számok csak erre a készülékre vonatkoznak, így egyediek. Kérjük, írja fel ezeket a számokat az alábbi mezŒkbe, és Œrizze meg a használati útmutatót az esetleges késŒbbi felhasználás céljából. Kérjük, csatolja ehhez az oldalhoz a vásárlást igazoló számlát is.
Vásárlás dátuma : A forgalmazó neve : A forgalmazó címe : Forgalmazó telefonszáma : Modell száma : Gyártási sorozatszám :
A készülék használata elŒtt, helyezze el és állítsa be a hıtŒgépet a használati útmutatóban elŒírt módon.
Soha ne a hálózati vezetéknél fogva húzza ki a hálózati csatlakozót a konnektoraljzatból.
A készülék elmozdításakor ügyeljen arra, nehogy elessen a hálózati vezetékben, vagy a készülékben kárt okozzon.
Miután a készüléket felállította a helyén, ne érintse meg a hideg felületeket, különösen ne nedves kézzel. A bŒr könnyen odaragadhat ezekhez a hideg felületekhez.
Tisztítás alkalmával és karbantartáskor húzza ki a hálózati vezetéket a konnektoraljzatból. Soha ne érjen a hálózati vezetékhez nedves kézzel, mert az áramütést okozhat.
Soha ne szerelje, hajlítsa vagy csavarja meg erŒsen a hálózati vezetéket, mert az áramütést vagy tüzet okozhat. EllenŒrizze a készülék helyes földelését.
Ne tegyen a hıtŒbe üvegbŒl készült tárolóedényeket, mert azok elrepedhetnek, ahogy a tartalmuk kitágul.
Soha ne tegye kezét az automatikus jégkészítŒbe, mert az balesetet okozhat. Ügyeljen arra, hogy fiatal gyerekek ne játszanak a hıtŒgéppel. Soha ne lépjen fel, vagy másszon fel a frissen tartó rekesz ajtajára. Ilyenkor a
hıtŒgép károsodhat, vagy akár fel is borulhat, ezzel komoly balesetet okozva. Ha lehetséges, csatlakoztassa a hıtŒgépet külön konnektoraljzatba, hogy elkerülje az
elektromos hálózat túlterhelését. A fagyasztó-hıtŒt úgy kell elhelyezni, hogy a hálózati csatlakozó könnyen elérhetŒ
legyen, hogy adott esetben baleset bekövetkezésekor könnyen ki lehessen húzni a csatlakozót.
Ha az áramellátó kábel megsérül, akkor azt gyártóval, szerelŒvel vagy hasonlóan képzett szakemberrel ki kell cseréltetni, hogy elkerüljük a balesetveszélyt.
A csatlakozózsinórt ne módosítsa és ne használjon hosszabbítót.
Ez elektromos áramütést vagy tüzet okozhat.
Ne használjon
hosszabbítót
A hálózati
csatlakozó
elérhetŒsége
Az áramellátó
kábel cseréje
Figyelem!
BevezetŒ
29
Fontos biztonsági elŒírások
30
Egy üres hıtŒszekrény veszélyes csábítást jelenthet egy gyermek számára. Régi, vagy használaton kívül helyezett hıtŒszekrényrŒl távolítsa el az ajtószigetelést, a reteszt vagy az egész ajtót, azonban a polcokat hagyja benne, ezzel megakadályozva, hogy a gyerekek a hıtŒgépbe mászhassanak. A hıtŒk gyerekek nem használhatják felügyelet nélkül. Ügyeljen arra, hogy gyermekei nem játszanak a hıtŒgéppel.
Ne tároljon a hıtŒgépben, és ne használjon a hıtŒgép közelében benzint vagy más gyúlékony anyagot.
Elektromos zárlat esetén földeléssel megelŒzhetŒ, vagy csökkenthetŒ az áramütés veszélye. Az áramütés veszélyeinek elkerülése érdekében megfelelŒ módon földelje hıtŒgépét. Bizonytalanság esetén keresse fel a legközelebbi villanyszerelŒt vagy szakembert.
Vigyázat!
Balesetveszélyes
hely gyermekek
számára
Ne tároljon a
hıtŒgépben
A készülék
földelése
BevezetŒ
MEGJEGYZÉS
ElképzelhetŒ, hogy egyes részek hiányoznak az Ön készülékébŒl. Ezek a részek más modelleken találhatók, vagy opcionálisak (pl. frissen tartó rekesz).
Fagyasztó HıtŒtér
Tejtermék polc
Automatikus
jégkészítŒ
Lámpa
Polcok
Polcok
Ajtórekeszek
Fiók
Fiók
Ajtórekesz
Alsó
díszküszöb
Lámpa
Polcok
Tojástartó
Polc (osztható vagy normál)
Frissen tartó rekesz
(opcionális)
Borosüveg tartó (Mıanyag vagy drót)
Dobozos ital-tároló
(opcionális)
Páratartalom kapcsoló
Ajtórekesz
Ajtórekesz
Varázszóna (opcionális) /Zöldségtartó-fiók (opcionális)
Zöldségtartó-fiók
Tároló üzemmód kapcsoló (Húsok/Zöldségek) (opcionális)
A hıtŒszekrény kezelŒszervei és egységei
Loading...
+ 102 hidden pages