Page 1
BOTTOM FREEZER
REFRIGERATOR
User’s Guide
Please read this guide thoroughly before operating and
keep it handy for reference at all times.
FRIGORIFERO CON
CONGELATORE
INFERIORE
Guida dell’utente
Leggere questa guida con attenzione prima dell'uso e
conservarla come riferimento.
æÀ°∂π√∫∞∆∞æÀ∫∆∏™
√‰ËÁ›Â˜ ÃÚ‹Û˘
¶·Ъ·О·ПФ‡МВ ‰И·‚¿ЫЩВ ‰ИВНФ‰ИО¿ ЩИ˜ Ф‰ЛБ›В˜ ¯Ъ‹ЫЛ˜
ЪИУ ЩЛ ПВИЩФ˘ЪБ›· О·И ОЪ·Щ‹ЫЩВ ЩИ˜ ЫВ ¤У·
ЪФЫ‚¿ЫИМФ М¤ЪФ˜ БИ· У· ·У·К¤ЪВЫЩВ ЫВ ·˘Щ¤˜
ФФИ·‰‹ФЩВ ЫЩИБМ‹.
P/No. MFL37933557
Page 2
2
TABLE OF CONTENTS
English Version 2
Safety Instructions 3–10
Parts and Features 11
Refrigerator Installation 12–21
Unpacking Your Refrigerator 12
Installation 12
Base Cover 12
Removing and Replacing
Your Refrigerator Handles
and Doors 13–20
Leveling and Door Alignment 21
Using Your Refrigerator 22–28
Ensuring Proper Air Circulation 22
Multi-Flow 22
Setting the Controls 22
Adjusting Control Settings 23
Food Storage Guide 23
Storing Frozen Food 24
❿❿
Refrigerator section
Refrigerator Shelves 25
Bottle Holder 25
Crisper Humidity Control 26
Removing Crisper 26
Glide ‘N’ Serve 26
Modular Door Bin 27
Dairy Bin 27
Utility Bin 27
❿❿
Freezer section
Durabase Divider 28
Ice Tray 28
Care and Cleaning 29–30
General Cleaning Tips 29
Outside 29
Inside Walls 29
Door Liner and Gaskets 29
Plastic Parts 29
Condenser Coils 29
Light Bulb Replacement 29–30
Power Interruptions 30
When you go on vacation 30
When you move 30
Troubleshooting Guide 31–34
ww
This product is exclusive use at 230V/50Hz.
You should purchase transformer of more than 2.0KVA when you want to use it at the 110V area.
You can't use it anywhere except 50Hz area.
Page 3
This guide contains many important safety messages. Always read and obey all safety messages.
This is the safety alert symbol. It alerts you to safety messages that inform you
of hazards that can kill or hurt you or others, or cause damage to the product.
All safety messages will be preceded by the safety alert symbol and the hazard signal word
DANGER, WARNING, CAUTION. These words mean:
BASIC SAFETY PRECAUTIONS
SAFETY MESSAGES
You will be killed or seriously injured if you don’t follow instructions.
You can
be killed or seriously injured if you don’t follow instructions.
Indicates an imminently hazardous situation which, if not avoided,
may
result in minor or moderate injury, or product damage only.
All safety messages will identify the hazard, tell you how to reduce the chance of injury, and tell you
what can happen if the instructions are not followed.
3
WARNING
CAUTION
DANGER
Child entrapment and suffocation are not
problems of the past. Junked or abandoned
refrigerators are still dangerous…even if they will
sit for just a few days. If you are getting rid of
your old refrigerator, please follow the
instructions at right to help prevent accidents.
BEFORE YOU THROW
AWAY YOUR OLD
REFRIGERATOR OR
FREEZER
• Take off the doors.
• Leave the shelves in place so
that children may not easily
climb inside.
ww
DANGER:
RISK OF CHILD ENTRAPMENT
CFC DISPOSAL
Your old refrigerator may have a cooling system
that used CFCs (chlorofluorocarbons). CFCs are
believed to harm stratospheric ozone.
If you are throwing away your old refrigerator,
make sure the CFC refrigerant is removed for
proper disposal by a qualified servicer. If you
intentionally release this CFC refrigerant, you can
be subject to fines and imprisonment under
provisions of environmental legislation.
Page 4
GROUNDING REQUIREMENTS
IMPORTANT: Please read carefully.
TO CONNECT ELECTRICITY
RECOMMENDED GROUNDING
METHOD
The refrigerator should always be plugged into its
own individual properly grounded electrical outlet
rated for 230 Volts, 50 Hz, AC only, and fused at
15 or 20 amperes.
This provides the best performance and also
prevents overloading house wiring circuits which
could cause a fire hazard from overheated wires.
It is recommended that a separate circuit serving
only this appliance be provided.
Use a receptacle which cannot be turned off with
a switch or pull chain. Do not use an extension
cord.
Where a standard two-prong wall outlet is
encountered, it is your personal responsibility and
obligation to have it replaced with a properly
grounded three-prong wall outlet.
Do not, under any circumstances, cut or
remove the third (ground) prong from the
power cord.
NOTE: Before performing any type of installation,
cleaning,or removing a light bulb, turn the control
(Thermostat, Refrigerator Control or Freezer
Control, depending on the model)to OFF and
then disconnect the refrigerator from the electrical
source. When you are finished,reconnect the
refrigerator to the electrical source and reset the
control (Thermostat, Refrigerator Control or
Freezer Control, depending on the model) to the
desired setting.
4
• Repair or replace immediately all electric service
cords that have become frayed or otherwise
damaged. Do not use a cord that shows cracks or
abrasion damage along its length or at either the
plug or connector end.
• When moving your refrigerator away from the wall,
be careful not to roll over or damage the power
cord.
• Keep fingers out of pinch point areas; clearances
between the doors and cabinet are necessarily
small. Be careful closing doors when children are
in the area.
• This refrigerator must be properly installed in
accordance with the Attention Installer
Instructions that were taped to the front of the
refrigerator.
• Don’t touch the lamp, in case of light on the long
time, Because it can be very hot.
• DO NOT refreeze frozen foods which have thawed
completely. The United States Department of
Agriculture in Home and Garden Bulletin No. 69
says:
…You may safely refreeze frozen foods that have
thawed if they still contain ice crystals or if they
are still cold—below 4°C.
…Thawed ground meats, poultry or fish that have
any off-odor or off-color should not be refrozen
and should not be eaten. Thawed ice cream
should be discarded. If the odor or color of any
food is poor or questionable, get rid of it.
The food may be dangerous to eat.
Even partial thawing and refreezing reduces the
eating quality of foods, particularly fruits,
vegetables and prepared foods. The eating quality
of red meats is affected less than that of many
other foods. Use refrozen foods as soon as
possible to save as much of their quality as you
can.
ww
WARNING
SAVE THESE INSTRUCTIONS
ww
WARNING
Electrical Shock Hazard
FOR PERSONAL SAFETY, this appliance
must be properly grounded. Have the wall
outlet and the circuit checked by a qualified
electrician to make sure the outlet is properly
grounded.
Page 5
IMPORTANT SAFETY INSTRUCTIONS
5
ww
WARNING
The dedicated outlet should be used.
• Using several devices at
one outlet may cause fire.
• The electric leakage
breaker may damage food
and the dispenser may be
leaked.
Do not allow the power plug to face upward
or to be squeezed at
the back of the
refrigerator.
Water may be flown into or
the plug may be damaged,
which causes fire or
electric shock.
1. When connecting the power
To reduce the risk of fire, electric shock, or injury to persons when using your product,
basic safety precautions should be followed, including the following.
Read all instructions before using this appliance.
Don’t use an extension cord
If possible, connect the refrigerator to its own
individual electrical outlet to prevent it and other
appliances or household lights from causing an
overload that could cause a power outage.
Accessibility of Supply Plug
The refrigerator-freezer should be so positioned
that the supply plug is accessible for quick
disconnection when accident happens.
Supply Cord Replacement
If the supply cord is damaged, it must be
replaced by the manufacturer or its service agent
or a similarly qualified person in order to avoid a
hazard.
ww
WARNING
• The refrigerant and insulation blowing gas used
in the appliance require special disposal
procedures. When disposal, please consult with
service agent or a similarly qualified person.
ww
WARNING
• Please do not use a dishwasher to clean the
lower drawers; the high temperature may cause
damage to the baskets which make them
unusable.
Do not allow the power cord bent or pressed
by the heavy object to
be damaged.
It may damage the power
cord to cause fire or electric
shock.
Do not extend or modify the length of the
power plug.
It causes electric shock or fire
by the electric damage of the
power cord or others.
Page 6
ww
WARNING
6
1. When connecting the power
To reduce the risk of fire, electric shock, or injury to persons when using your product,
basic safety precautions should be followed, including the following.
Read all instructions before using this appliance.
Unplug the power plug when cleaning,
handling or replacing the interior lamp of the
refrigerator.
• It may cause electric shock or injury.
• When replacing the interior
lamp of the refrigerator, make
sure that the rubber ring for
preventing the electric spark
within the socket is not taken
off.
Do not pull out the cord or touch the power
plug with wet hands.
• It may cause electric
shock or injury.
Remove water or dust from the power plug
and insert it with the ends of the pins
securely connected.
Dust, water or unstable
connection may fire or
electric shock.
Make sure of grounding.
The incorrect grounding
may cause breakdown
and electric shock.
When the power cord or the power plug is
damaged or the holes of
the outlet are loosed, do
not use them.
It may cause electric shock or
short circuit to make fire.
Grounding
Conductor
Copper
flat
More than
75cm
Page 7
IMPORTANT SAFETY INSTRUCTIONS
7
Do not place the lit candle within the
refrigerator to deodorize.
It may cause explosion or fire.
Do not store the medicine or the academic
materials at the refrigerator.
When the material with the
strict temperature control is
stored, it may be
deteriorated or it may
make an unexpected
reaction to cause any risk.
Do not use the combustible spray near the
refrigerator.
It may cause fire.
The Academic
Medicine
The Medicine
Avoid the heating devices.
It may cause fire.
Do not place flower vase, cup, cosmetics,
medicine or any container
with water on the
refrigerator.
It may cause fire, electric shock
or injury by dropping down.
Use the submerged refrigerator after
checking it.
It may cause electric
shock or fire.
2. When using the refrigerator
Do not place the heavy object or the
dangerous object
(container with liquid) on
the refrigerator.
It may be dropped to cause injury,
fire or electric shock when
opening or closing the door.
Do not install the refrigerator in the wet
place or the place which
water or rain splashes.
Deterioration of insulation of
electric parts may cause
electric leakage.
Do not cling to the door or the shelves of the
door or the home bar of the freezer or the
cool chamber.
It may make the refrigerator
fallen down or damage the
hands. Especially, do not
allow the children to do the
above.
Do not use or store inflammable materials
ether, benzene, alcohol, medicine, LP gas,
spray or cosmetics
near or in the
refrigerator.
It may cause explosion
or fire.
Benzene
Ether
Thinner
Page 8
IMPORTANT SAFETY INSTRUCTIONS
8
2. When using the refrigerator
When disposing the refrigerator, remove the
packing materials from
the door.
It may cause to lock out the
child.
Install the refrigerator on the solid and level
floor.
Installing it on the unstable
place may cause death by
falling down the refrigerator
when opening or closing the
door.
When you want to dispose the refrigerator,
contact to the down-block office.
When you want to dispose the
large living waste such as
electric home appliance and
furniture, you’d better contact
the local down-block office.
Down-block
office
Do not insert the hands or the metal stick
into the exit of cool air, the cover, the bottom
of the refrigerator, the
heatproof grill (exhaust
hole) at the backside.
It may cause electric shock or
injury.
This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or
lack of experience and knowledge, unless
they have been given supervision or
instruction concerning use of the appliance
by a person responsible for their safety.
Children should be supervised to ensure that
they do not play with the appliance.
Do not allow any person except the qualified
engineer to disassemble, repair or alter the
refrigerator.
It may cause injury,
electric shock or fire.
Do not use the refrigerator for non-domestic
purpose (storing medicine or testing
material, using at the ship,
etc.).
It may cause an unexpected
risk such as fire, electric shock,
deterioration of stored material
or chemical reaction.
Do not spray water at the outside or the
inside of the refrigerator or do not clean it
with benzene or thinner.
Deterioration of insulation of
electric parts may cause
electric shock or fire.
When any strange smell or smoke is
detected from the refrigerator, power plug
get rid of electric
outlet immediately
and contact to the
service center.
It may cause fire.
ThinnerThinner
Service
center
When gas is leaked, do not touch the refrigerator
or the outlet and ventilate the room immediately.
• The explosion by spark may cause fire or burn.
• Because this refrigerator uses natural gas (isobutene,
R600a) as the environment-friendly refrigerant, even a
small amount (50~60g) is combustible. When the gas is
leaked by the severe
damage during delivering,
installing or using the
refrigerator, any spark may
cause fire or burn.
Page 9
ww
CAUTION
9
Violating this direction may cause injury or damage house or furniture. Always be careful, please.
Wait for 5 minutes or
longer when
reconnecting the plug.
It may cause the operation of
the freezer to fail.
After
5minutes
Do not touch food or containers at the
freezer with wet hands.
It may cause frostbite.
Pull out the power plug not by grasping
the cord but the plug
of its end.
It may cause electric shock
or short circuit to fire.
Do not put bottle in the freezer.
It may freeze the
contents to break the
bottle to cause injury.
Do not insert the hands into the bottom
of the refrigerator.
The iron plate of the
bottom may cause injury.
Do not install the refrigerator in the wet
place or the place
which water or rain
splashes.
Deterioration of insulation of
electric parts may cause
electric leakage.
Because opening or closing the door of
the refrigerator may cause injury to the
person around it, be careful, please.
Opening or closing the
door may cause feet or
hands to be caught in
the chink in door or the
child to be get hurt by
the corner.
Carry the refrigerator with the handle bar
at the bottom of the front and the top of
the rear.
Otherwise, your hands
may be slipped to
cause injury.
Do not put any living
animal in the
refrigerator.
Page 10
IMPORTANT SAFETY INSTRUCTIONS
10
This appliance contains a small amount of isobutane refrigerant (R600a),
natural gas with high environmental compatibility, but it is also combustible.
When transporting and installing the appliance, care should be taken to
ensure that no parts of the refrigerating circuit are damaged. Refrigerant
squirting out of the pipes could ignite or cause an eye injury. If a leak is
detected, avoid any naked flames or potential sources of ignition and air the
room in which the appliance is standing for several minutes.
In order to avoid the creation of a flammable gas air mixture if a leak in the
refrigerating circuit occurs, the size of the room in which the appliance may
be sited depends on the amount of refrigerant used. The room must be 1m
2
in
size for every 8g of R600a refrigerant inside the appliance. The amount of
refrigerant in your particular appliance is shown on the identification plate
inside the appliance. Never start up an appliance showing any signs of
damage. If in doubt, consult your dealer.
ww
WARNING
w Keep ventilation openings, in the appliance enclosure or in the built-in structure,
clear of obstruction.
w Do not use mechanical devices or other means to accelerate the defrosting
process, other than those recommended by the manufacturer.
w Do not damage the refrigerant circuit.
w Do not use electrical appliances inside the food storage compartments of the
appliance, unless they are of the type recommended by the manufacturer.
w The refrigerant and insulation blowing gas used in the appliance require special
disposal procedures. When disposal, please consult with service agent or a
similarly qualified person.
Page 11
PARTS AND FEATURES
Use this page to become more familiar with the parts and features. Page references are included for
your convenience.
NOTE: This guide covers several different models. The refrigerator you have purchased may
have some or all of the items listed below. The locations of the features shown below may not
match your model.
Digital Sensor Control
Modular Door Bins (p. 27)
Shelves (p. 25)
Crisper (p. 26)
(Keeps fruits and vegetable fresh and crisper)
Glide‘N’Serve (p. 26)
Ice Tray (p. 28)
Dairy Bin (p. 27)
Utility Bin (p. 27)
Bottle Holder (p. 25)
Divider (p. 28)
11
A
B
C
D
E
G
H
I
J
F
H
I
A
B
C
D
E
F
G
B
J
Page 12
UNPACKING YOUR REFRIGERATOR
Remove tape and any temporary labels from your
refrigerator before using. Do not remove any
warning-type labels, the model and serial number
label, or the TechSheet that is attached to back
wall of the refrigerator.
To remove any remaining tape or glue, rub the
area briskly with your thumb. Tape or glue residue
can also be easily removed by rubbing a small
amount of liquid dish soap over the adhesive with
your fingers. Wipe with warm water and dry.
Do not use sharp instruments, rubbing alcohol,
flammable fluids or abrasive cleaners to remove
tape or glue. These products can damage the
surface of your refrigerator. For more information,
see the Important Safety Instructions section.
Refrigerator shelves are installed in the shipping
position.
Please reinstall shelves according to your
individual storage needs.
• To reduce the risk of electric shock, do not
install the refrigerator in a wet or damp area.
• Select a place where a water supply can be
easily connected for the automatic icemaker.
ww
CAUTION: Avoid placing the unit near heat
sources, direct sunlight or moisture.
INSTALLATION
• To minimize noise and vibration, the refrigerator
MUST be installed on a solidly constructed floor.
• Carpeting and soft tile surfaces are not
recommended.
• Never install the refrigerator on a platform or
weakly supported structure.
1. To avoid vibration, the unit must be level. If
required, adjust the leveling screws to
compensate for unevenness of the floor. The
front should be slightly higher than the rear to
aid in door closing. Leveling screws can be
turned easily by tipping the cabinet slightly. Turn
the leveling screws clockwise ( ) to raise the
unit, counterclockwise ( ) to lower it.
2. Install this appliance in an area where the
temperature is between 13°C and 43°C. If the
temperature around the appliance is too low or
high, cooling ability may be adversely affected.
3.
Too small a distance from adjacent items may
result in lowered freezing capability and
increased electricity consumption charges. Allow
at least 24 in. (61 cm) in front of the refrigerator to
open the doors.
NEXT
1. Clean your refrigerator thoroughly and wipe off
all dust accumulated during shipping.
2. Install accessories such as ice cube bin,
drawers, shelves, etc., in their proper places.
They are packed together to prevent possible
damage during shipment.
3. Let your refrigerator run for at least 2 or 3 hours
before putting food in it. Check the flow of cold
air in the freezer compartment to ensure proper
cooling. Your refrigerator is now ready for use.
BASE COVER
To remove the base cover
1. Open the Freezer Drawer. (Drawer not shown
for clarity.)
2. Once drawer is open there is sufficient
clearance to remove screws on top of cover.
To replace base cover:
• Place cover into
position and insert and
tighten screws.
REFRIGERATOR INSTALLATION
12
ww
WARNING
Excessive Weight Hazard
Use two or more people to move and install
refrigerator.
Failure to do so can result in back or other injury.
ww
WARNING
When Moving Your Refrigerator:
Your refrigerator is heavy. When moving the
refrigerator for cleaning or service, be sure to
protect the floor. Always pull the refrigerator
straight out when moving it. Do not wiggle or
walk the refrigerator when trying to move it, as
floor damage could occur.
ww
WARNING
Explosion Hazard
Keep flammable materials and vapors, such as
gasoline, away from refrigerator.
Failure to do so can result in death, explosion
or fire.
1" (2.54 cm)
Page 13
REFRIGERATOR INSTALLATION
HOW TO REMOVE DOOR HANDLES
To move refrigerator through a house door, it maybe necessary to remove refrigerator and freezer door
handles.
NOTE: Handle appearance may vary from
illustrations on this page.
1. Removing Refrigerator Handle
• Loosen the set screws with a
2.5 mm (3/32") Allen wrench and
remove the handle.
NOTE: If the handle mounting
fasteners need to be tightened or
removed, use a 1/4" Allen wrench.
2. Removing Freezer Drawer Handle
• Loosen the set screws located on the
lower side of the handle with a 3.1
mm (1/8") Allen wrench and remove
the handle.
NOTE: If the handle mounting
fasteners need to be tightened or
removed, use a 1/4" Allen
wrench.
13
Mounting
Fasteners
Set Screw
Allen
Wrench
Page 14
REFRIGERATOR INSTALLATION
HOW TO REPLACE DOOR HANDLES
NOTE: Handle appearance may vary from illustrations on this page.
1. Replacing Refrigerator Door Handle
• Place the handle on the door by
adjusting handle footprints to fit
mounting fastners and tighten the set
screws with a 2.5 mm (3/32") Allen
wrench.
NOTE: If the handle mounting fasteners
need to be tightened or removed use a
1/4" Allen wrench.
2. Replacing Freezer Drawer Handle
• Place the handle on the door by
adjusting handle footprints to fit
mounting fastners and tighten the set
screws on the bottom of the handle with
a 3.1 mm (1/8") Allen wrench.
NOTE: If the handle mounting fasteners
need to be tightened or removed use a
1/4" Allen wrench.
14
Mounting
Fasteners
Page 15
REFRIGERATOR INSTALLATION
HOW TO REMOVE REFRIGERATOR DOOR
1. Removing Refrigerator Door
NOTE: Handle appearance may vary.
IMPORTANT: Before you begin, turn the refrigerator OFF and unplug it. Remove food and any bins
from doors.
❿ Left Door
• Loosen the cover screw (1).
• Disconnect wire harness (2).
• Remove the ground screw (3).
• Rotate the lever hinge (4) counter clockwise and lift off the top hinge (5).
• Raising it up enough to clear the middle hinge pins.
• Place the door on a non-scratching surface with the inside up.
❿ Right Door
• Remove the right door followed by the same way described above.
• Rotate the lever hinge (4) clockwise at this time, removing the top hinge (5).
ww
CAUTION: When removing top hinge, be careful that the door does not fall forward.
15
1
1
2
2
3
3
4
4
5
5
Page 16
REFRIGERATOR INSTALLATION
2. Replacing Refrigerator Door
❿❿
Right Door
• Lower the door onto the middle
hinge pin (6).
• Make sure the door is aligned with
the cabinet.
• Replace the top hinge (5) by
rotating the lever hinge (4) counter
clockwise to secure it.
• Make sure the gasket on the door
is flush against the cabinet and is
not folded.
• Support the door on the handle
side while securing. And make sure
the door is straight and the gap
between the doors is even across
the front.
• Install the ground screw (3) and
connect the wire harness (2).
• Tighten the cover screw (1).
❿❿
Left Door
• Replace the left door followed by
the same way described above.
• When replacing the top hinge (5),
rotate the lever hinge (4) clockwise
at this time.
ww
CAUTION: Be careful of missing
the washer [part(7)]. Because it
can be easily taken off.
16
6
6
7
7
Page 17
HOW TO REMOVE AND REINSTALL
THE PULLOUT DRAWER
ww
CAUTION
• To avoid possible injury or product or property
damage, you will need two people to perform
the following instructions.
• When you remove the drawer, do not hold the
handle. It may come off and could cause injury.
• When laying the drawer down, be careful not to
damage the floor or hurt your feet with the sharp
edges on the hinge side.
Removing Pullout Drawer
❿❿
Top Drawer
1. To remove the freezer drawer, pull the drawer
open to full extension. Remove the drawer and
Ice tray by lifting the basket from the rail
system.
2. Remove the screws of the rail on both sides.
3. With both hands, hold both sides of the door
and pull it up to separate it from the rails.
4. With both hands, flex the center bar enough to
allow the gears on both ends to release from
the track.
w CAUTION: When you remove the drawer, do
not hold the handle. If it may come off and it
could cause personal injury.
w CAUTION: When laying the drawer down, be
careful not to damage the floor or hurt your
feet by the sharp edges on hinge side.
REFRIGERATOR INSTALLATION
17
Page 18
REFRIGERATOR INSTALLATION
ww
CAUTION
• To avoid possible injury or product or property
damage, you will need two people to perform
the following instructions.
• When you remove the drawer, do not hold the
handle. It may come off and could cause injury.
• When laying the drawer down, be careful not to
damage the floor or hurt your feet with the sharp
edges on the hinge side.
Removing Pullout Drawer
❿❿
Bottom drawer
1. To remove the freezer drawer, pull the drawer
open to full extension. Remove the lower
DuraBase ® basket by lifting the basket from
the rail system.
2. Remove the screws of the rail on both sides.
3. With both hands, hold both sides of the door
and pull it up to separate it from the rails.
4. With both hands, flex the center bar enough to
allow the gears on both ends to release from
the track.
w CAUTION: When you remove the drawer, do
not hold the handle. If it may come off and it
could cause personal injury.
w CAUTION: When laying the drawer down, be
careful not to damage the floor or hurt your
feet by the sharp edges on hinge side.
18
Page 19
REFRIGERATOR INSTALLATION
HOW TO REMOVE AND REINSTALL
THE PULLOUT DRAWER
ww
CAUTION
• To avoid possible injury or product or property
damage, you will need two people to perform
the following instructions.
ww
DANGER
Risk of Child Entrapment
• To prevent accidental child and pet entrapment
or suffocation risk, DO NOT allow them to play
inside of the freezer drawer.
• DO NOT step or sit on the freezer drawer.
Reinstalling Pullout Drawer
❿❿
Top Drawer
1. To reinstall the freezer drawer, hold the center
bar with both hands and pull it out until both
rails are fully extended.
2. Hook door supports (1) into rail tabs (2).
3. Lower door into final position and tighten the
screws (3). Make sure you have a right rail
cover for each side.
4. With the drawer pulled out to full extension,
insert the drawer and Ice tray in the rail
assembly.
w WARNING: To prevent accidental child and
pet entrapment or suffocation risk.
DO NOT allow them to play inside of drawer.
w WARNING: DO NOT step or sit down on
freezer.
19
2
1
3
Page 20
REFRIGERATOR INSTALLATION
ww
CAUTION
• To avoid possible injury or product or property
damage, you will need two people to perform
the following instructions.
ww
DANGER
Risk of Child Entrapment
• To prevent accidental child and pet entrapment
or suffocation risk, DO NOT allow them to play
inside of the freezer drawer.
• DO NOT step or sit on the freezer drawer.
Reinstalling Pullout Drawer
❿❿
Bottom drawer
1. To reinstall the freezer drawer, hold the center
bar with both hands and pull it out until both
rails are fully extended.
2. Hook door supports (1) into rail tabs (2).
3. Lower door into final position and tighten the
screws (3). Make sure you have a right rail
cover for each side.
4. With the drawer pulled out to full extension,
insert the lower basket in the rail assembly.
w WARNING: To prevent accidental child and
pet entrapment or suffocation risk.
DO NOT allow them to play inside of drawer.
w WARNING: DO NOT step or sit down on
freezer.
20
2
1
3
Page 21
REFRIGERATOR INSTALLATION
LEVELING AND DOOR ALIGNMENT
Leveling
After installing, secure the product with the LEG
not to move left or right.
Your refrigerator has two front leveling screws—
one on the right and one on the left. If your
refrigerator seems unsteady or you want the
doors to close easier, adjust the refrigerator’s tilt
using the instructions below:
1. Plug the refrigerator’s power cord into a
3-prong grounded outlet. Move the refrigerator
into its final position.
2. Turn the leveling leg clockwise to raise that
side of the refrigerator or counterclockwise to
lower it. It may take several turns of the
leveling leg to adjust the tilt of the refrigerator.
NOTE: Having someone push against the top
of the refrigerator takes some weight off the
leveling legs. This makes it easier to adjust the
legs.
3. Open both doors again and check to make
sure that they close easily. If not, tilt the
refrigerator slightly more to the rear by turning
both leveling screws clockwise. It may take
several more turns, and you should turn both
leveling screws the same amount.
4. Re-adjust if necessary.
5. Replace the base cover.
NOTE: Your new refrigerator is uniquely
designed with two fresh food doors. Either door
can be opened or closed independently of one
another. You may have to exert slight pressure
on doors to get them to close completely.
Door Alignment
If the space between your doors is uneven, follow
the instructions below to align the doors:
1. With one hand, lift up the door you want to
raise at middle hinge.
2. With other hand, use pliers to insert snap ring
as shown.
3. Insert additional snap rings until the doors are
aligned. (Three snap rings are provided with
unit.)
w CAUTION
• To avoid possible injury or product or property
damage, you will need two people to perform
the following instructions.
Level the refrigerator by using an 11/32 inch
(8mm) wrench or a flat blade screw driver.
Turn the leveling legs (CCW) to raise or (CW) to
lower the height of the front of the refrigerator.
NOTE: The front of the refrigerator should be
slightly higher than the back.
NOTE: If someone pushes backward against the
top of the refrigerator, weight is lifted off of the
leveling legs, which makes adjustment easier.
Open both doors to make sure they close easily.
If not, raise the leveling legs higher by turning
both clockwise the same amount. Once the
refrigerator is level, replace the kick-plate.
NOTE: Your new refrigerator is uniquely
designed with two fresh food doors. Either door
can be independently opened or closed.
You will have to exert slight pressure on the
doors to close them completely.
NOTE: In order not to move the refrigerator back
and forth, fix it with the 'Adjust' to the floor to
install and use.
21
Page 22
USING YOUR REFRIGERATOR
ENSURING PROPER AIR
CIRCULATION
In order to ensure proper temperatures, air must
flow between the refrigerator and freezer
sections. As shown in the illustration below, air
enters at top of freezer and circulates down.
From bottom of freezer, air is forced up to top of
refrigerator. Air enters refrigerator through top
vent, then circulates and exists at bottom, where
it returns to freezer.
MULTI-FLOW
• Multi-Flow means powerful and effective cooling
operation. This is especially noticeable when
new food is placed in the refrigerator
compartment.
• If water or foreign substances enter the cool air
vent while cleaning, efficiency will be lowered. In
addition, if gasket is damaged, efficiency may
be lowered because of escaping cool air.
Do not block any of cool air vents with food
packages. If the vents are blocked, airflow will be
interrupted and temperature and moisture
problems may occur.
IMPORTANT: Because air circulates between
both sections, any odors formed in one section
will transfer to the other. You must thoroughly
clean both sections to eliminate odors. To
prevent odor transfer and drying out of food, wrap
or cover foods tightly. (See the Food Storage
Guide section for details.)
SETTING THE CONTROLS
• Your refrigerator has two controls that let you
regulate the temperature in the freezer and
refrigerator compartments.
• Initially set the REFRIGERATOR CONTROL at
3°C and the FREEZER CONTROL at –18°C.
Leave it at this setting for 24 hours (one day) to
stabilize. Then adjust the compartment
temperature as desired.
• Refrigerator control: 0°C to 8°C
The lower the number setting, the colder the
refrigerator compartment will become.
• Freezer control: –21°C to –13°C
When the setting is at a lower number, the
freezer compartment becomes colder. But the
refrigerator compartment becomes warmer
because less cold air flows into the refrigerator.
• Express Freezing:
Press the Express Freezing key and the LED
will turn on. This function will remain activated
for 24 hours and intensify the cooling speed of
freezer and increase the amount of ice.
22
Page 23
USING YOUR REFRIGERATOR
23
CONDITION/
REASON:
■ REFRIGERATOR section
too warm
– Door opened often
– Large amount of food
added
– Room temperature very
warm
■ FREEZER section too
warm/ice not made fast
enough
– Door opened often
– Large amount of food
added
– Very cold room
temperature (can’t cycle
often enough)
– Heavy ice usage
– Air vents blocked by items
■ REFRIGERATOR section
too cold
– Controls not set correctly
for your conditions
■ FREEZER section too
cold
– Controls not set correctly
for your conditions
RECOMMENDED
ADJUSTMENT:
Set
REFRIGERATOR
control to next
lower number,
wait 24 hours,
then re-check
Set FREEZER
control to next
lower number,
wait 24 hours,
then re-check
Move items out of
airstream
Set
REFRIGERATOR
control to next
higher number,
wait 24 hours,
then re-check
Set FREEZER
control to next
higher number,
wait 24 hours,
then re-check
Items
Butter or
margarine
Cheese
Milk
Eggs
Fruit
Leafy
vegetables
Vegetables
with skins
(carrots,
peppers)
Fish
Leftovers
How to
❿ Keep opened butter in a
covered dish or closed
compartment. When storing an
extra supply, wrap in freezer
packaging and freeze.
❿ Store in the original wrapping
until you are ready to use it.
Once opened, rewrap tightly in
plastic wrap or aluminum foil.
❿ Wipe milk cartons. For best
storage, place milk on interior
shelf, not on door shelf.
❿ Store in original carton or
Utility Bin on interior shelf, not
on door shelf.
❿ Wash, let dry, and store in
refrigerator in plastic bags or
in the crisper. Do not wash or
hull berries until you are ready
to use them. Sort and keep
berries in their original
container in a crisper, or store
in a sloosely closed paper bag
on a refrigerator shelf.
❿ Remove store wrapping and
trim or tear off bruised and
discolored areas. Wash in cold
water and drain. Place in
plastic bag or plastic container
and store in crisper.
❿ Place in plastic bags or plastic
container and store in crisper.
❿ Use fresh fish and shellfish the
same day purchased.
❿ Cover leftovers with plastic
wrap or aluminum foil. Plastic
containers with tight lids can
also be used.
ADJUSTING CONTROL SETTINGS
Give the refrigerator time to cool down completely
before making final adjustments. It is best to wait
24 hours before doing this. The mid-settings
indicated in the previous section should be
correct for normal household refrigerator usage.
The controls are set correctly when milk or juice
is as cold as you like and when ice cream is firm.
The refrigerator control functions as the
thermostat for the entire appliance (refrigerator
and freezer sections). The higher the number
setting, the longer the compressor will run to
keep the temperature colder. The freezer control
adjusts the cold air flow from the freezer to the
refrigerator. Setting the freezer control to a lower
temperature keeps more cold air in the Freezer
compartment to make it colder.
If you need to adjust temperatures in the
refrigerator or freezer, start by adjusting the
refrigerator. Then wait 24 hours before checking
the freezer temperature. If it is too warm or too
cold, then adjust the freezer control.
Use the settings listed in the chart below as a
guide. Always remember to wait at least 24
hours between adjustments.
FOOD STORAGE GUIDE
Wrap or store food in the refrigerator in airtight
and moisture-proof material unless otherwise
noted. This prevents food odor and taste transfer
throughout the refrigerator. For dated products,
check date code to ensure freshness.
Page 24
USING YOUR REFRIGERATOR
STORING FROZEN FOOD
NOTE: For further information about preparing
food for freezing or food storage times, check a
freezer guide or a reliable cookbook.
Packaging
Successful freezing depends on correct
packaging. When you close and seal the
package, it must not allow air or moisture in or
out. If it does, you could have food odor and taste
transfer throughout the refrigerator and also dry
out frozen food.
Packaging recommendations:
• Rigid plastic containers with tight-fitting lids
• Straight-sided canning/freezing jars
• Heavy-duty aluminum foil
• Plastic-coated paper
• Non-permeable plastic wraps
• Specified freezer-grade self-sealing plastic bags
Follow package or container instructions for
proper freezing methods.
Do not use:
• Bread wrappers
• Non-polyethylene plastic containers
• Containers without tight lids
• Wax paper or wax-coated freezer wrap
• Thin, semi-permeable wrap
ww
CAUTION: Do not keep beverage cans or
plastic food containers in the freezer
compartment. They may be break if it freezes.
Freezing
Your freezer will not quick-freeze any large
quantity of food. Do not put more unfrozen food
into the freezer than will freeze within 24 hours.
Leave enough space in the freezer for air to
circulate around packages. Be careful to leave
enough room at the front so the door can close
tightly.
Storage times will vary according to the quality
and type of food, the type of packaging or wrap
used (airtight and moisture-proof) and the storage
temperature. Ice crystals inside a sealed package
are normal. This simply means that moisture in
the food and air inside the package have
condensed, creating ice crystals.
NOTE: Allow hot foods to cool at room
temperature for 30 minutes, then package and
freeze. Cooling hot foods before freezing saves
energy.
24
Page 25
USING YOUR REFRIGERATOR
REFRIGERATOR SECTION
REFRIGERATOR SHELVES
The shelves in your refrigerator are adjustable to
meet your individual storage needs. Your model
may have glass or wire shelves.
Storing similar food items together in your
refrigerator and adjusting the shelves to fit
different heights of items will make finding the
exact item you want easier; it will also reduce the
amount of time the refrigerator door is open,
saving energy.
IMPORTANT: Do not clean glass shelves with
warm water when they are cold. Shelves may
break if exposed to sudden temperature changes
or impact, such as bumping. For your protection,
glass shelves are made with tempered glass,
which will shatter into small pebble-sized pieces.
NOTE: Glass shelves are heavy. Use special
care when removing them to avoid dropping
them.
Adjusting Shelves
Remove shelves from the shipping position and
replace shelves in the position you want.
• To remove a shelf—Tilt up the front of the
shelf. Lift up the back and pull out the shelf.
• To reinstall a shelf—Tilt up the front of the
shelf and guide the shelf hooks into the slots at
a desired height. Then lower the front of the
shelf so that the hooks drop into the slots.
ww
CAUTION : Make sure that shelves are level
from one side to the other. Failure to do so
may result in the shelf falling or spilling food.
Sliding Out Shelves
You can slide glass shelves in and out of your
refrigerator as follows.
• To slide the shelf out, carefully pull front of
shelf toward you.
• To slide shelf in, push shelf in until it stops.
BOTTLE HOLDER
Bottles can be stored laterally with this wine
holder. It can be attached to any shelf.
Wine holder can be removed by pulling it straight
out and installed by placing it at the end of the
shelf you want and pushing it inward.
25
Page 26
USING YOUR REFRIGERATOR
CRISPER HUMIDITY CONTROL
You can control the amount of humidity in the
moisture-sealed crispers. Store vegetables or
fruits requiring more or less humidity in separate
crispers. Adjust the control to any setting
between HIGH and LOW.
• LOW lets moist air out of the crisper for best
storage of fruits.
• HIGH keeps moist air in the crisper for best
storage of fresh, leafy vegetables.
ww
CAUTION : The glass shelf over the crisper is
not firmly secured. Be careful when tilting.
REMOVING CRISPER
1. To remove, pull the drawer out to full
extension.
2. Lift the front of the crisper up, then pull it
straight out.
3.
To install, slightly tilt up the front and insert the
drawer into the frame and push it back into place.
To remove the glass
1. Lift up the glass under the crisper cover.
2. Pull the glass up and out.
GLIDE‘N’SERVE
The Glide‘N’Serve provides storage space with a
variable temperature control that keeps the
compartment colder than refrigerator.
This drawer can be used for large party trays, deli
items, or beverages. (but this drawer can’t be
used for vegetable.)
Controls
The control regulates the air temperature in the
drawer. Set control level to COLD (print on
surface) to provide normal refrigerator
temperature. Use the COLDER (print on surface)
setting for meats or other deli items.
NOTE: Cold air directed to the Glide‘N’Serve can
decrease refrigerator temperature. Refrigerator
control may need to be adjusted.
To replace Glide‘N’Serve
1. To remove, pull the drawer out to full
extension.
2. Lift the front of the drawer up, then pull it
straight out.
3. To install, slightly tilt up the front and insert the
drawer into the frame and push it back into
place.
26
1
Page 27
USING YOUR REFRIGERATOR
MODULAR DOOR BIN
The door bins are removable for easy cleaning
and adjusting.
1. To remove the bin, simply lift the bin up and
pull straight out.
2. To replace the bin, slide it in above the desired
support button and push down until it stops.
ww
WARNING : Somebody can be hurt if door
bins are not firmly assembled.
ww
NOTE : DO NOT adjust a bin that is loaded
with food.
ww
CAUTION : DO NOT allow children to play
with baskets. Sharp corners on baskets could
cause injury.
DAIRY BIN
1. To remove the dairy bin, simply lift it and pull
straight out.
2. To replace the dairy bin, slide it in above the
desired location and push down until it stops.
UTILITY BIN
Store the utility bin on interior shelf, not on door
shelf.
ww
CAUTION : Do not use the utility bin as an ice
storage bin in the freezer compartment. The
utility bin can easily break if it freezes.
27
Page 28
USING YOUR REFRIGERATOR
FREEZER SECTION
DURABASE DIVIDER
The Durabase divider allows you to organize the
Durabase area into sections.
ww
WARNING: If the Durabase divider is
removed, there is enough open space for
children or pets to crawl inside. To prevent
accidental child and pet entrapment or
suffocation risk, DO NOT allow them to play
inside of drawer.
ICE TRAY
1. To make ice cubes, fill the ice tray with water
and place it.
2. Ice will be dropped into the ice storage bin by
rotating Ice separation handle of ice making
compartment.
28
Page 29
CARE AND CLEANING
Both the refrigerator and freezer sections defrost
automatically. However,clean both sections about
once a month to prevent odors. Wipe up spills
immediately.
GENERAL CLEANING TIPS
• Unplug refrigerator or disconnect power.
• Remove all removable parts, such as shelves,
crispers, etc. Refer to sections in Using Your
Refrigerator for removal instructions.
• Use a clean sponge or soft cloth and a mild
detergent in warm water.Do not use abrasive or
harsh cleaners.
• Hand wash, rinse and dry all surfaces
thoroughly.
• Plug in refrigerator or reconnect power.
OUTSIDE
Waxing external painted metal surfaces helps
provide rust protection. Do not wax plastic parts.
Wax painted metal surfaces at least twice a year
using appliance wax (or auto paste wax). Apply
wax with a clean, soft cloth.
For products with a stainless steel exterior, use a
clean sponge or soft cloth and a mild detergent in
warm water. Do not use abrasive or harsh
cleaners. Dry thoroughly with a soft cloth.
INSIDE WALLS (allow freezer to
warm up so cloth won’t stick)
To help remove odors, you can wash the inside
of the refrigerator with a mixture of baking soda
and warm water. Mix 2 tablespoons baking soda
to 1 quart of water (26 g soda to 1 liter water.) Be
sure the baking soda is completely dissolved so
does it not scratch the surfaces of the
refrigerator.
ww
CAUTION: While cleaning the inside, do not
spray water.
DOOR LINERS AND GASKETS
Do not use cleaning waxes, concentrated
detergents, bleaches, or cleaners containing
petroleum on plastic refrigerator parts.
PLASTIC PARTS (covers and panels)
Do not use window sprays, abrasive cleansers, or
flammable fluids. These can scratch or damage the
material.
CONDENSER COILS
Remove Back cover.
Use a vacuum cleaner with an
extended attachment to clean
condenser coils.Vacuum coils
when dusty or dirty.Coils may
need to be cleaned as often as every other month.
LIGHT BULB REPLACEMENT
NOTE:
• Not all appliance bulbs will fit your refrigerator. Be
sure to replace the bulb with one of the same size,
shape and wattage.
• The light bulbs will turn off if door is left open for
seven continuous minutes. Shutting door for one
second will light bulbs to come back on.
To change Refrigerator Light Bulbs
1. Unplug Refrigerator, or disconnect power at the
circuit breaker.
2. If necessary, remove top shelf or shelves.
3. Using a flat instrument, gently pry the lamp cover
loose in the front as shown. Rotate downward to
remove rear tabs.
4. Make sure the bulbs are cool to the touch.
Turn bulbs counterclockwise to remove. Insert
new bulb(s).
5. Replace with a new 60-watt appliance bulb.
6. Assemble in reverse order by snapping the Lamp
Cover in, engaging the rear tabs followed by the
front tabs.
29
ww
WARNING
Electrical Shock Hazard
Before replacing a burned-out light bulb,either
unplug the refrigerator or turn off power at the
circuit breaker or fuse box.
NOTE: Moving the control to the OFF position
does not remove power to the light circuit.
ww
WARNING
Explosion Hazard
Use non-flammable cleaner.
Failure to do so can result in death, explosion, or fire.
Page 30
CARE AND CLEANING
To change freezer light
1. Unplug refrigerator power cord form outlet.
2. Using a flat instrument, gently pry the lamp
cover loose in the front as shown. Rotate
downward to remove the rear tabs.
3. Make sure the bulb is cool to the touch. Turn
the bulb counterclockwise to remove.
4. Replace with a new 60-watt appliance bulb.
5. Insert tabs on back of cover into slots in
freezer ceiling. Push cover up to snap front into
place.
ww
CAUTION: DO NOT place fingers inside of
cover. Lamp may be hot.
POWER INTERRUPTIONS
1. If the power will be out for 24 hours or less,
keep all refrigerator doors closed to help foods
stay cold and frozen.
2. If the power will be out for more than 24 hours:
a) Remove all frozen food and store it in a
frozen food locker.
WHEN YOU GO ON VACATION
If you choose to leave the refrigerator on
while you are away, follow these steps to
prepare your refrigerator before you leave.
1. Use up any perishables and freeze other
items.
2. Empty the ice tray.
If you choose to turn the refrigerator off
before you leave, follow these steps.
1. Remove all food from the refrigerator.
2. Depending on your model, set the thermostat
control (refrigerator control) to OFF. See the
Setting the Controls section.
3. Clean refrigerator, wipe it and dry well.
4. Tape rubber or wood blocks to the tops of both
doors to prop them open far enough for air to
get in. This stops odor and mold from building
up.
WHEN YOU MOVE
When you are moving your refrigerator to a new
home, follow these steps to prepare it for the
move.
1. Remove all food from the refrigerator and pack
all frozen food in dry ice.
2. Depending on your model, turn the thermostat
control (refrigerator control) to OFF. See the
Setting the Controls section.
3. Unplug the refrigerator.
4. Clean, wipe and dry thoroughly.
5. Take out all removable parts, wrap them well
and tape them together so they don’t shift and
rattle during the move. Refer to sections in
Using your Refrigerator for removal
instructions.
6. Depending on the model, raise the front of the
refrigerator so it rolls more easily OR screw in
the leveling legs all the way so they don’t
scrape the floor. See the Door Closing
section.
7. Tape the doors shut and tape the power cord
to the refrigerator cabinet.
When you get to your new home, put everything
back and refer to the Installing Your
Refrigerator section for preparation instructions.
30
Page 31
TROUBLESHOOTING GUIDE
UNDERSTANDING SOUNDS YOU
MAY HEAR
Your new refrigerator may make sounds that your
old one didn’t make. Because the sounds are new
to you, you might be concerned about them. Most of
the new sounds are normal. Hard surfaces, like the
floor, walls and cabinets, can make the sounds
seem louder than they actually are. The following
describes the kinds of sounds and what may be
making them.
• The defrost timer will click when the automatic
defrost cycle begins and ends. The thermostat
control (or refrigerator control, depending on the
model) will also click when cycling on and off.
• Rattling noises may come from the flow of
refrigerant, the water line, or items stored on top
of the refrigerator.
• Your refrigerator is designed to run more
efficiently to keep your food items at the desired
temperature. The high efficiency compressor
may cause your new refrigerator to run longer
than your old one, and you may hear a
pulsating or high-pitched sound.
• You may hear the evaporator fan motor
circulating the air through the refrigerator and
freezer compartments.
• As each cycle ends, you may hear a gurgling
sound due to the refrigerant flowing in your
refrigerator.
• Contraction and expansion of the inside walls
may cause a popping noise.
• Water dripping on the defrost heater during a
defrost cycle may cause a sizzling sound.
• You may hear air being forced over the
condenser by the condenser fan.
• You may hear water running into the drain pan
during the defrost cycle.
31
Check if…
The power supply cord is unplugged.
A household fuse has blown or circuit
breaker tripped.
The refrigerator control is set to the
OFF position.
Refrigerator is in the defrost cycle.
The refrigerator is not resting solidly
on the floor.
The power supply cord is unplugged.
Light bulb is loose in the socket.
Light bulb has burned out.
Door is left open for seven continuous
minutes.
REFRIGERATOR
DOES NOT
OPERATE
VIBRATION OR
RATTLING
NOISE
LIGHTS DO
NOT WORK
Then…
❿Firmly plug the cord into a live outlet
with proper voltage.
❿Replace the fuse or reset the circuit
breaker.
❿Refer to the Setting the Controls
section on page 22.
❿Wait about 30 minutes for defrost
cycle to end.
❿Floor is weak or uneven or leveling
legs need adjusting.
See Installation section on page 12.
❿Firmly plug the cord into a live outlet
with proper voltage.
❿Turn the refrigerator control to the OFF
position and unplug the refrigerator.
Gently remove the bulb and reinsert.
Then plug in refrigerator and reset the
refrigerator control.
❿Replace with an appliance bulb of the
same wattage, size and shape
available at your local hardware store.
(See the Changing the Light Bulb(s)
section on pages 29–30.) Turn the
temperature control to the OFF
position and unplug the refrigerator
prior to replacement.
❿Shutting door for one second will light
bulbs to come back on.
Page 32
TROUBLESHOOTING GUIDE
32
Check if…
The refrigerator that was replaced was
an older model.
The room temperature is hotter than
normal.
The door is opened often or a large
amount of food has just been added.
The refrigerator was recently plugged
in and the refrigerator control was set
correctly.
The refrigerator control is not set
correctly for the surrounding conditions.
The doors are not closed completely.
The condenser coils are dirty.
The refrigerator is not level.
Food packages are blocking the door
open.
The ice tray, crisper cover, pans,
shelves, door bins or baskets are out
of position.
The gaskets are sticking.
The refrigerator wobbles or seems
unstable.
The doors were removed during
product installation and not properly
replaced.
The door is not closing properly.
The door is opened often.
COMPRESSOR
MOTOR SEEMS
TO RUN TOO
MUCH
DOORS WILL
NOT CLOSE
COMPLETELY
FROST OR ICE
CRYSTALS ON
FROZEN FOOD
Then…
❿Modern refrigerators with more storage
space require more operating time.
❿The motor will run longer under warm
conditions. At normal room
temperatures, expect your motor to
run about 40% to 80% of the time.
Under warmer conditions, expect it to
run even more often.
❿Adding food and opening the door
warms the refrigerator. It is normal for
the refrigerator to run longer in order to
cool the refrigerator back down. Adding
a large amount of food warms the
refrigerator. See the Food Storage
Guide section on page 23. In order to
conserve energy, try to get everything
you need out of the refrigerator at once,
keep food organized so it is easy to find
and close the door as soon as the food
is removed.
❿The refrigerator will take up to 24
hours to cool completely.
❿See the Adjusting Control Settings
section on page 23.
❿Push the doors firmly shut. If they will
not shut all the way, see Doors will
not close completely below.
❿This prevents air transfer and makes
the motor work harder.
Clean the condenser coils. Refer to
the Care and Cleaning section on
pages 29–30.
❿See Leveling and Door Alignment
on page 21.
❿Rearrange food containers to clear
door and door shelves.
❿Push bins all the way in and put
crisper cover, pans, shelves and
baskets into their correct positions.
See the Using Your Refrigerator
section on pages 22–28.
❿Clean gaskets and the surface that
they touch. Rub a thin coat of paraffin
wax on the gaskets after cleaning.
❿Level the refrigerator. Refer to the
Leveling and Door Alignment
section on page 21.
❿Remove and replace the doors
according to the Removing and
Replacing Refrigerator handles and
doors section on pages 13–20, or call
a qualified service technician.
❿See Doors will not close completely
above.
❿When the door is opened, warm,
humid air is allowed in the freezer,
resulting in frost.
Page 33
TROUBLESHOOTING GUIDE
33
Check if…
The icemaker was recently installed.
The ice has been stored for too long.
The food has not been wrapped tightly
in either compartment.
The water supply contains minerals
such as sulfur.
The interior of refrigerator needs
cleaning.
Ice storage bin needs cleaning.
The refrigerator is defrosting.
It is more humid than normal.
The sounds may be normal for your
refrigerator.
The freezer temperature is cold
enough to produce ice.
Door left open.
Smaller cube size level is selected.
Water shutoff valve connecting
refrigerator to water line may be
clogged.
The gaskets are dirty or sticky.
The door is reopened within a short
time after having been opened.
ICE HAS OFFTASTE OR
ODOR
THERE IS
WATER IN THE
DEFROST
DRAIN PAN
THE
REFRIGERATOR
SEEMS TO
MAKE TOO
MUCH NOISE
THE
ICEMAKER IS
NOT
PRODUCING
ICE OR ICE
CUBES ARE
FREEZING TOO
SLOWLY
CUBES
PRODUCED BY
ICEMAKER
ARE TOO
SMALL
THE DOORS
ARE
DIFFICULT TO
OPEN
Then…
❿ Discard first few batches of ice to avoid
discolored or off-flavored ice.
❿ Throw away old ice and make new
supply.
❿ Rewrap foods since odors may migrate
to the ice if food is not wrapped
properly.
❿ A filter may need to be installed
(or replaced) to eliminate taste and
odor problems.
❿ See Care and Cleaning section on
pages 29–30.
❿ Empty and wash bin. Discard old cubes.
❿ The water will evaporate. It is normal
for water to drip into the defrost pan.
❿ Expect that the water in the defrost
pan will take longer to evaporate. This
is normal when it is hot or humid.
❿ Refer to the Understanding Sounds
You May Hear section on page 31.
❿ Wait 24 hours after hook-up for ice
production. See the Setting the
Controls section on page 22.
❿ Check to see if something is holding
the door open.
❿ Select larger cube size using cube size
selector.
❿ Call a plumber to clear the valve.
❿ Clean gaskets and the surfaces that
they touch. Rub a thin coat of
appliance polish or kitchen wax on the
gaskets after cleaning.
❿ When you open the door, warmer air
enters the refrigerator. As the warm air
cools, it can create a vacuum. If the
door is hard to open, wait 5 minutes to
allow the air pressure to equalize, then
see if it opens more easily.
Page 34
TROUBLESHOOTING GUIDE
34
Check if…
The air vents are blocked. Cold air
circulates from the freezer to the fresh
food section and back again through
air vents in the wall dividing the two
sections.
The doors are opened often.
The control is not set correctly for the
surrounding conditions.
A large amount of food has just been
added to the refrigerator or freezer.
The food is not packaged correctly.
The doors are not closing completely.
The weather is humid.
A self-defrost cycle was completed.
TEMPERATURE
IS TOO WARM
OR THERE IS
INTERIOR
MOISTURE
BUILDUP
Then…
❿ Locate air vents by using your hand to
sense airflow and move all packages
that block vents and restrict airflow.
Refer to Multi-Flow on page 22 for the
location of air vents.
❿ When the door is opened, warm humid
air is allowed into the refrigerator. The
more the door is opened, the faster the
humidity builds up, and the more warm
air the refrigerator must cool. In order
to keep the refrigerator cool, try to get
everything you need out of the
refrigerator at once, keep food
organized so it is easy to find and close
the door as soon as the food is
removed.
❿ Refer to the Setting the Controls
section on page 22.
Wait 24 hours for temperatures to
stabilize or even out. If the temperature
is too cold or too warm, move the dial
one number at a time.
❿ Adding food warms the refrigerator. It
can take a few hours for the refrigerator
to return to normal temperature.
❿ Wrap food tightly and wipe off damp
containers prior to storing in the
refrigerator to avoid moisture
accumulation. If necessary, repackage
food according to the guidelines in the
Food Storage Guide section on page
23.
❿ See Doors will not close completely
on page 32.
❿ In humid weather, air carries moisture
into refrigerator when doors are
opened.
❿ It is normal for droplets to form on the
back wall after the refrigerator selfdefrosts.
DISPOSAL OF YOUR OLD APPLIANCE
1. When this crossed-out wheeled bin symbol is attached to a product it means the
product is covered by the European Directive 2002/96/EC.
2. All electrical and electronic products should be disposed of separately from the
municipal waste stream via designated collection facilities appointed by the
government or the local authorities.
3. The correct disposal of your old appliance will help prevent potential negative
consequences for the environment and human health.
4. For more detailed information about disposal of your old appliance, please contact
your city office, waste disposal service or the shop where you purchased the product.
Page 35
MEMO
35
Page 36
MEMO
36
Page 37
Loading...