LG GR-486ZMQ User Manual
PLEASE
READ THIS OWNER’S MANUAL THOROUGHLY
BEFORE OPERATING AND KEEP IT FOR
REFERENCE AT ALL TIMES.
OWNER’S MANUAL
REFRIGERATORFREEZER
2
INSTALLATION ..................................................... 3
INNER PARTS ....................................................... 4
OPERATIONS......................................................... 5
Starting
Controls For Refrigerator Compartment
Controls For Freezer Compartment
Ice Beam Door Cooling
Ice Making (Optional)
Fresh Zone
Defrosting
Deodorizer (Optional)
Dairy Conner
Vitamin Vegetable drawer (Optional)
SUGGESTIONS ON FOOD STORAGE .............. 9
CLEANING ........................................................... 10
GENERAL INFORMATION ................................. 10
LAMP REPLACEMENT....................................... 11
IMPORTANT WARNINGS ................................. 11
BEFORE CALLING FOR SERVICE .................. 12
CONTENTS
3
INSTALLATION
INSTALLATION
THIS REFRIGERATOR IS MANUFACTURED WITH GREAT CARE, AND UTILIZES THE
LATEST IN TECHNOLOGY.
WE ARE CONFIDENT THAT YOU WILL BE FULLY SATISFIED WITH IT'S PERFORMANCE
AND RELIABILITY.
BEFORE YOU START YOUR REFRIGERATOR, PLEASE READ THIS BOOKLET CAREFULLY.
IT PROVIDES EXACT INSTRUCTIONS FOR INSTALLATION, OPERATION AND
MAINTENANCE, AND ALSO SUPPLIES SOME USEFUL HINTS.
1. Select a good location.
Place your refrigerator where it is easy to
use.
2. Avoid placing the unit near heat sources,
direct sunlight or moisture.
3. There must be proper air circulation around
your refrigerator to keep it operating
efficiently.
If your refrigerator is placed in a recessed
area in the wall, allow at least 10 inches or
greater clearance above the refrigerator and
2 inches or more from the wall.
The refrigerator should be elevated 1 inch
from the floor, especially if it is carpeted.
4. To avoid vibrations, the unit must be level. If
required, adjust the leveling screws to
compensate for unevenness of the floor.
The front should be slightly higher than the
rear to aid in door closing.
Leveling screws can be turned easily by
tipping the cabinet slightly.
Turn the leveling screws clockwise( ) to
raise the unit, counterclockwise( ) to
lower it.
5. Don't install this appliance below 5 °C. It may
cause the debasement of the refrigerator.
NEXT
1. Clean your refrigerator thoroughly and wipe
off all dust accumulated during shipping.
2. Install accessories such as ice cube box, etc.,
in their proper places.They are packed
together to prevent possible damage during
shipment.
3. You have a model with bar-type handle,
assemble the handle according to instruction
card.
4. Connect the power supply cord (or plug) to
the outlet. Don't double up with other
appliances on the same outlet.
5. Prior to storing food, leave your refrigerator
on for 2 or 3 hours.
Check the flow of cold air in the freezer
compartment to ensure proper cooling. Your
refrigerator is now ready for use.
●
This guide covers several different models. The refrigerator you have
purchased may have some or all of the features shown above.
NOTE
INNER PARTS
4
OPERATIONS
5
STARTING
When your refrigerator is first installed, allow it 2-3 hours to stabilize at normal operating temperatures
prior to filling it with fresh or frozen foods.
If operation is interrupted, wait 5 minutes before restarting.
●
Your refrigerator has two controls that let you regulate the
temperature in the freezer and refrigerator compartments.
●
The default setting of the temperature control button for the
refrigerator compartment is NORMAL. You can set the
refrigerator temperature using the Electro Temp Control.
Whenever pressing the button, the LED emit light. The
temperature of the compartment goes down as the LED
luminesce from MIN to MAX.
You can select the desired set point in five (5) steps between
minimum and maximum.
CONTROLS FOR REFRIGERATOR COMPARTMENT
• COLD AIR CONTROL - 1, 2, 3, 4, 5, 6, 7, 8, 9 Setting at "9", the
freezer compartment becomes colder. But the refrigerator
compartment becomes warmer because less cold air flows into the
refrigerator compartment.
• In cold weather the unit operates less and the freezer compartment has a tendency to warm up. For
colder freezer, turn the COLD AIR CONTROL to "7"~"9".
• If you take a lot of foods in the freezer or open its door frequently, its temperature is apt to be
somewhat higher. In this case, set the COLD AIR CONTROL dial between 7 and 9 to cool it. Return
the COLD AIR CONTROL dial to the original position to cut down the consumption of energy.
• In hot weather or to put much foods in the refrigerator compartment, the refrigerator
compartment has tendency to warm up.
For colder refrigerator, turn the COLD AIR CONTROL to "2"~"4" to direct more cold air into the
refrigerator compartment, and the REF TEMP CONTROL TO MAX.
Setting at "7"~"9" of the COLD AIR CONTROL, the refrigerator compartment will not be cold enough.
CONTROLS FOR FREEZER COMPARTMENT
• Setting the Freezer Knob at will satisfy 4 STAR.
Setting the Freezer Knob at NORMAL will have sufficient freezing effect, so it is recommended to set the
Knob at NORMAL.
Ice Trays
Ice Cube Box
Ice Trays
Ice Cube Box
Frame
OPERATIONS
6
ICEBEAM DOOR COOLING
●
Air vents are located to provide cool air flow to items stored
in the door shelves and at the front of the refrigerator
shelves.
●
If water of foreign substances enter the cool air vent while
cleaning, efficiency will be lowered. In addition, if gasket is
damaged, efficiency may be lowered owing to the escape
of cool air.
Cool air vent
ICE MAKING (OPTIONAL)
Choose the type of ice-making system you have.
General Type
●
To make ice cubes, fill the ice tray with water and
place it on the Ice cube box. Then insert the ice cube
box in the freezer compartment.
●
To remove ice cubes, hold the tray at its ends and
twist gently.
Twisting Ice Serve Type
●
To make ice cubes, fill the ice tray with water and
insert in its position.
●
To remove ice cubes, hold the knob of the tray and
turn gently. Then, ice cubes drop in the ice cube box.
●
You can remove Twisting Ice Serve to use freezer
compartment larger.
●
You should remove Ice Trays and Ice Cube Box first
then pull the frame out right side.
Loading...