LG FB790GD Users manual

APPENDIX G :
USER’S MANUAL
FCC ID : BEJFB790GD
A1
Important Precautions
On Safety
Use only the power cord supplied with the unit. In case you use another power cord, make sure that it is certified by the applicable national standards if not being provided by the supplier. If the power cable is faulty in any way, please contact the manufacturer or the nearest authorized repair service provider for a replacement.
The power supply cord is used as the main disconnect device. Ensure that the socket-outlet is easily accessible after installation.
Operate the monitor only from a power source indicated in the specifications of this manual or listed on the monitor. If you are not sure what type of power supply you have in your home, consult with your dealer.
Overloaded AC outlets and extension cords are dangerous. So are frayed power cords and broken plugs. They may result in a shock or fire hazard. Call your service technician for replacement.
Hands must be dry when holding the power plug to avoid an electric shock. Do not damage the power cord by disassembling, bending, pulling or heating up.
It can cause fire or electric shock. Make sure to completely insert the power plug. Insecure connections can cause
fire. Do not Open the Monitor.
There are no user serviceable components inside. There are Dangerous High Voltages inside, even when the power is OFF. Contact your dealer if the monitor is not operating properly.
To Avoid Personal Injury :
Do not place the monitor on a sloping shelf unless properly secured. Use only a stand recommended by the manufacturer. Do not try to roll a stand with small casters across thresholds or deep pile carpets.
A2
Important Precautions
To Prevent Fire or Hazards:
Always turn the monitor OFF if you leave the room for more than a short period of time. Never leave the monitor ON when leaving the house. Keep children from dropping or pushing objects into the monitor's cabinet openings. Some internal parts carry hazardous voltages. Do not add accessories that have not been designed for this monitor. During a lightning storm or when the monitor is to be left unattended for an extended period of time, unplug it from the wall outlet. Do not bring magnetic devices such as magnets or motors near the picture tube.
On Installation
Do not allow anything to rest upon or roll over the power cord, and do not place the monitor where the power cord is subject to damage.
Do not use this monitor near water such as near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool. Monitors are provided with ventilation openings in the cabinet to allow the release of heat generated during operation. If these openings are blocked, built-up heat can cause failures which may result in a fire hazard. Therefore, NEVER:
Block the bottom ventilation slots by placing the monitor on a bed, sofa, rug, etc. Place the monitor in a built-in enclosure unless proper ventilation is provided. Cover the openings with cloth or other material. Place the monitor near or over a radiator or heat source. Do not install the monitor in a dusty area. It can cause fire.
On Cleaning
Unplug the monitor before cleaning the face of the monitor screen. Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the
monitor screen because overspray may cause electrical shock.
On Repacking
Do not throw away the carton and packing materials. They make an ideal container in which to transport the unit. When shipping the unit to another location, repack it in its original material.
A3A3
Connecting the Monitor
Latch
Before setting up the monitor, ensure that the power is turned off to the monitor, computer system, and other attached devices. Carefully set the monitor face-down with the underside facing you.
Connecting the Tilt/Swivel stand
1. Align the hooks on the tilt/swivel stand with the matching slots in the base of
the monitor.
2. Insert the hooks into slots.
3. Slide the tilt/swivel stand toward the front of the monitor until the latches click
into the locked position.
NOTE
This illustration depicts the general model of connection. Your monitor may differ from the items shown in the picture.
Hook
Slot
Hook
Connecting the Monitor
Using the Computer
1. Connect the signal cable. When mated, tighten the thumbscrews to secure the
connection.
2. Connect the power cord into a properly power outlet that is easily accessible and
close to the monitor.
NOTE
This is a simplified representation of the rear view. This rear view represents a general model; your monitor may differ from the view as shown.
Mac adapter
For Apple Macintosh use, a separate plug adapter is needed to change the 15 pin high density (3 row) D-sub VGA connector on the supplied cable to a 15 pin 2 row connector.
Wall-outlet type
*
PC-outlet type*
PC
MAC
Power Cord
Signal Cable
Digital signal
- DVI
*
Analog signal
D-sub
*
*
Varies according to model.
A4
A5
Control Panel Functions
Front Panel Controls
Buttons
Use these buttons to choose or adjust items in the on screen display.
MENU (or OSD) Button
Use this button to enter or exit the on screen display.
This Indicator lights up green when the monitor operates normally. If the monitor is in DPM (Energy Saving) mode, this indicator color changes to amber.
Power (DPMS) Indicator
Use this button to turn the monitor on or off.
Power Button
Use this button to change the input mode.
Use this button to enter a selection in the on screen display.
DIGITAL SELECT Button
The Contrast and Brightness functions are also available in the On Screen Display (OSD) menu.
88
Control Direct Access Function
Control Function
Button
Button
Bring up Contrast adjustment
Bring up Brightness adjustment
DIGITAL
A6
On Screen Display (OSD) Control Adjustment
Screen Adjustment
Making adjustments to the image size, position and operating parameters of the monitor is quick and easy with the On Screen Display Control system. A short example is quick and easy given below to familiarize you with the use of the controls. The following section is an outline of the available adjustments and selections you can make using the OSD.
To make adjustments in the On Screen Display, follow these steps:
Press the MENU (or OSD) Button, then the main menu of the OSD appears.
To access a control, use the or Buttons. When the icon you want becomes highlighted, press the SELECT (or SET) Button.
Use the Buttons to adjust the item to the desired level.
Accept the changes by pressing the SELECT (or SET) Button.
Exit the OSD by Pressing the MENU (or OSD) Button.
NOTE
Allow the monitor to stabilize for at least 30 minutes before making image adjustments.
Case 1
Case 2
Main menu Sub menu Reference
A7
On Screen Display(OSD) Selection and Adjustment
To adjust the brightness and contrast of the screen
Brightness Contrast
The following table indicates all the On Screen Display control, adjustment, and setting menus.
BRIGHTNESS/
CONTRAST
POSITION
V Position H Position
SIZE
V Size H Size
SHAPE
Tilt Side Pincushion S Pincushion Balance Parallelogram Trapezoid H Corner Top Corner Bottom Corner
COLOR
PRESET
6500K
9300K Temp R/G/B(User Color)
COLOR HUE SATURATION FLESH TONE RECALL COLOR
SETUP
Video Level Language
OSD Time
INPUT SIGNAL
To adjust the position of the screen
To adjust the size of the screen
To adjust the shape of the screen
To customize the color of the screen
To customize the screen status for a user's operating environment
A
D
: Adjustable
A : Analog Input D : Digital Input
A8
On Screen Display(OSD) Selection and Adjustment
SPECIAL
Degauss Recall Reset Moire H Moire
V Moire Convergence Purity
To improve the clarity and stability of the screen
: Adjustable
Main menu Sub menu Reference
A : Analog Input D : Digital Input
A
D
A9
On Screen Display(OSD) Selection and Adjustment
You were introduced to the procedure of selecting and adjusting an item using the OSD system. Listed below are the icons, icon names, and icon descriptions of the all items shown on the Menu.
OSD Adjust Description
Brightness
To adjust the brightness of the screen.
Contrast
To adjust the contrast of the screen.
Vertical Position
To move image up and down.
Horizontal Position
To move image left and right.
To adjust the brightness and contrast of the screen
To adjust the position of the screen
OSD Adjust Description
NOTE
The order of icons may differ depending on the model (A9~A12).
A10
On Screen Display(OSD) Selection and Adjustment
Vertical Size
To adjust image height.
Horizontal Size
To adjust image width.
To adjust the size of the screen
OSD Adjust Description
To adjust the shape of the screen
OSD Adjust Description
Tilt
To correct image rotation.
Side Pincushion
To correct a concave or convex bowing of the image.
Side Pincushion Balance
To correct the balance of both sides bowing.
Parallelogram
To correctly adjust the skew of the image.
Trapezoid
To correct geometric distortion.
H Corner
*
Top Corner
*
Bottom Corner
*
To correct an irregular distortion of the displayed image.
* This function is available for
designated models only.
A11
This item is used to select the monitor's input signal level. The normal level used for most PCs is 0.7V. If the screen becomes suddenly washed­out or blurred, please select 1.0V and try again.
To choose the language in which the control names are displayed. OSD Menus are available in 11 languages: English, German, French, Spanish, Italian, Swedish, Finnish, Portuguese, Korean, Chinese and Russian.
Set the OSD time, i.e. the length of time a menu will remain on-screen before it shuts off automatically. Adjust the time to 5, 10, 20, 30 or 60 seconds.
VIDEO LEVEL
LANGUAGE
OSD TIME
INPUT SIGNAL
INPUT SIGNAL
On Screen Display(OSD) Selection and Adjustment
PRESET
TEMP
RED GREEN BLUE
COLOR HUE SATURATION FLESH TONE
RECALL COLOR
6500K/ 9300K
Select the screen color.
• 6500K: Slightly reddish white.
• 9300K: Slightly bluish white. Select the screen temperature which you
prefer among reddish or bluish or any color in between.
Set your own color levels.
To customize the color of the screen
OSD Adjust Description
To customize the screen status for a user's operating environment
OSD Adjust Description
INPUT SIGNAL
Select the display screen hue which you prefer. The factory preset value is 50.
Select the display screen saturation which you prefer. The factory preset value is 50.
Select the display screen flesh tone which you prefer. The factory preset value is 50.
Select the input signal(ANALOG or DIGITAL). You can easily select the display screen of each Computer's when you connect two computers to this monitor simultaneously.
Recall all screen color hue,saturation and flesh tone from user selected to the factory preset value. (Each factory preset value is 50)
A12
DEGAUSS
RECALL
RESET
MOIRE
CONVER­GENCE
*
PURITY
*
On Screen Display(OSD) Selection and Adjustment
To manually demagnetize the screen to avoid showing incorrect images or colors.
You can use this function to reload the modified parameters for screen display operation, as specified by the user after purchase: Position, Size, Side Pincushion,
Trapezoid (These recalled options may differ depending on the mode selected: Preset, User, or New).
If you don’t want to recall the monitor to these modified settings, use the button to select CANCEL and then press the SELECT (or SET) button.
Return to all factory default settings If you don’t want to reset the monitor, use the
button to select CANCEL and then
press the SELECT (or SET) button. This item allows you to reduce the degree of
moire. (Moire is caused by interference Horizontal Scan Line with the periodical dot screen). It is normally OFF(H:0/V:0). The moire adjustments may affect the focus of the screen. Moire adjustments may shake slightly while the moire reduction function is on.
This is to adjust the alignment of red and blue fields.
Use to adjust the purity on the screen if the color appears uneven.
To improve the clarity and stability of the screen
OSD Adjust Description
* This function is available for
designated models only.
A13
Troubleshooting
Check the following before calling for service.
No image appears
Is the power cord of the monitor connected?
Is the power indicator light on?
Is the power on and the
power indicator green? Is the power indicator
amber?
Do you see an "OUT OF
FREQUENCY" message on the screen?
Do you see a
"NO SIGNAL"message
on the screen?
Check and see if the power cord is connected properly to
the power outlet.
Press the Power button.
Adjust the brightness and the contrast.
If the monitor is in power saving mode, try moving the
mouse or pressing any key on the keyboard to bring up the screen.
Press the digital select button.
This message appears when the signal from the PC
(video card) is out of horizontal or vertical frequency range of the monitor. See the 'Specifications' section of this manual and configure your monitor again.
This message appears when the signal cable between
your PC and your monitor is not connected. Check the signal cable and try again.
Or press the "Digital" button to choose another input
signal.
Is the vertical frequency less than 70Hz or is your monitor set to the interlaced mode?
Do you have any magnetic material such as adapter, or high­voltage line near to your monitor?
Do you hear a "~ding" sound while the monitor is flickering?
Set the vertical frequency to 72Hz or higher, and consult the video card user manual for instructions on converting to a non-interlaced mode. (You can set this option under the Display icon of the Control Panel.)
Remove magnetic sources, such as power adapters, speakers, or high-voltage lines, away from the monitor.
Use the normal degaussing function. This function clears the screen and reduces any screen blur that may occur due to the surrounding magnetic field. The screen may flicker for about 5 seconds, accompanied by a "~ding" sound.
The screen is flickering.
Loading...
+ 30 hidden pages