LG F10B8QDT2 Owner’s Manual

I nstallation

Install or store where it will not be exposed to temperatures below freezing or exposed to the weather. Properly ground washer to conform with all governing codes and ordinances.

The base opening must not be obstructed by carpeting when the washing machine is installed on a carpeted floor.

In countries where there are areas which may be subject to infestation by cockroaches or other vermin, pay particular attention to keeping the appliance and its surroundings in clean condition at all times. Any damage which may be cause by cockroaches or other vermin will not be covered by the appliance guarantee.

Transit bolts

The appliance is fitted with transit bolts to prevent internal damage during transport.

• Packing and all transit bolts must be removed before using the washer.

When unpacking the base, be sure to remove

the additional packing support in the middle	Washer
of the base packing.
	Base Packing

Removing transit bolts

1. To prevent internal damage during transport, the special 4 bolts are locked. Before operating the washer, remove

the bolts along with the rubber bungs.

•If they are not removed, it may cause heavy vibration, noise and malfunction.

2. Unscrew the 4 bolts with the spanner supplied.

3. Take out the 4 bolts along with the rubber bungs by slightly twisting the bung. Keep the 4 bolts and the spanner for future use.

•Whenever the appliance is transported, the transit bolts must be refitted.

4. Close the holes with the caps supplied.

5

Installation

Installation place requirement

Drain Hose

Washer

Laundry

Tub

approx.

2cm

Level floor :

Allowable slope under entire washer is 1˚

Power outlet :

Must be within 1.5 meters of either side of location of washer. Do not overload the outlet with more than one appliance.

Additional Clearance :

For wall, door and floor modeling is required. (10cm : rear /2cm:right & left side)

Do not place or store laundry products on top of washer at any times.

They can damage the finish or controls.

Positioning

Install the washer on a flat hard floor.

Make sure that air circulation around the washer is not impeded by carpets,rug etc.

•Never try to correct any unevenness in the floor with pieces of wood, cardboard or similar materials under the washer.

•If it is impossible to avoid positioning the washer next to a gas cooker or coal burning stove,an insulating(85x60cm) covered with aluminum foil on the side facing the cooker or stove,must be inserted between the two appliance.

•The washer must not be installed in rooms where the temperature can drop below 0°C.

•Please ensure that when the washer is installed, it is easily accessible for the engineer in the event of a breakdown.

•With the washer installed adjust all four feet using the transit bolt spanner provided ensuring the appliance is stable, and a clearance of approximately 20mm is left between the top of the washer and the underside of the work-top.

6

Rev No.: 00

Date : 08.2013

I nstallation

This equipment is not designed for maritime use or for use mobile installations such as caravans, aircraft etc.

Turn off the stopcock if the machine is to be left for any length of time (e.g. holiday), especially if there is no floor drain(gully) in the immediate vicinity.

When disposing of the appliance, cut off the mains cable, and destroy the plug Disable the door lock to prevent young children being trapped inside.

Packaging material (e.g. Films, Styrofoam) can be dangerous for children. There is a risk of suffocation !

Keep all packaging well away from children

Installation of drain hose

•The drain hose should not be placed higher than 100 cm above the floor.

•Proper securing of the drain hose will protect the floor from damage due to water leakage.

•When the drain hose is too long, do not force back into the washer. This will cause abnormal noise.

•When installing the drain hose sink, secure it tightly with a string.

•Proper securing of the drain hose will protect the floor from damage due to water leakage.

9