LG E2280VV Users manual

Order Number : GETEC-C1-10-115 FCC Part 15 subpart B

Test Report Number : GETEC-E3-10-054 Page

APPENDIX G

: USER’S MANUAL

1 / 1

EUT Type: LED LCD Monitor

FCC ID.: BEJE2280VV

OWNER’S MANUAL

ENGLISH

LED LCD MONITOR

Please read this manual carefully before operating your set and retain it for future reference.

LED LCD MONITOR MODELS

E2280V E2380V E2280VX E2380VX

www.lg.com

Important Precautions

This unit has been engineered and manufactured to ensure your personal safety, however improper use may result in potential electrical shock or fire hazards. In order to allow the proper operation of all safeguards incorporated in this display, observe the following basic rules for its installation, use, and servicing.

On Safety

Use only the power cord supplied with the unit. In case you use another power cord, make sure that it is certified by the applicable national standards if not being provided by the supplier. If the power cable is faulty in any way, please contact the manufacturer or the nearest authorized repair service provider for a replacement.

The appliance coupler is used as the disconnect device.

Please make sure the device is installed near the wall outlet to which it is connected and that the outlet is easily accessible.

Operate the display only from a power source indicated in the specifications of this manual or listed on the display. If you are not sure what type of power supply you have in your home, consult with your dealer.

Overloaded AC outlets and extension cords are dangerous. So are frayed power cords and broken plugs. They may result in a shock or fire hazard. Call your service technician for replacement.

As long as this unit is connected to the AC wall outlet, it is not disconnected from the AC power source even if the unit is turned off.

Do not Open the Display:

There are no user serviceable components inside. There are Dangerous High Voltages inside, even when the power is OFF. Contact your dealer if the display is not operating properly.

To Avoid Personal Injury :

Do not place the display on a sloping shelf unless properly secured. Use only a stand recommended by the manufacturer. Do not drop an object on or apply impact to the product. Do not throw any toys or objects on the product screen. It can cause injury to human, problem to product and damage the display.

To Prevent Fire or Hazards:

Always turn the display OFF if you leave the room for more than a short period of time. Never leave the display ON when leaving the house. Keep children from dropping or pushing objects into the display's cabinet openings. Some internal parts carry hazardous voltages. Do not add accessories that have not been designed for this display. When the display is to be left unattended for an extended period of time, unplug it from the wall outlet. In the presence of thunder and lightning, never touch the power cord and signal cable because it can be very dangerous. It can cause electric shock.

Important Precautions

On Installation

Do not allow anything to rest upon or roll over the power cord, and do not place the display where the power cord is subject to damage.

Do not use this display near water such as near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool.

Displays are provided with ventilation openings in the cabinet to allow the release of heat generated during operation. If these openings are blocked, built-up heat can cause failures which may result in a fire hazard. Therefore, NEVER:

Block the bottom ventilation slots by placing the display on a bed, sofa, rug, etc. Place the display in a built-in enclosure unless proper ventilation is provided. Cover the openings with cloth or other material. Place the display near or over a radiator or heat source.

Do not rub or strike the Active Matrix LCD with anything hard as this may scratch, mar, or damage the Active Matrix LCD permanently.

Do not press the LCD screen with your finger for a long time as this may cause some afterimages.

Some dot defects may appear as Red, Green or Blue spots on the screen. However, this will have no impact or effect on the display performance.

If possible, use the recommended resolution to obtain the best image quality for your LCD display. If used under any mode except the recommended resolution, some scaled or processed images may appear on the screen. However, this is characteristic of the fixed-resolution LCD panel.

Leaving a fixed image on the screen for a long time may cause damage to the screen and cause image burn-in. Make sure to use a screen saver on the product. Burn-in and related problems are not covered by the warranty on this product.

Do not shock or scratch the front and sides of the screen with metallic objects. Otherwise, it may cause damage to the screen.

Make sure the panel faces forward and hold it with both hands to move. If you drop the product, the damaged product can cause electric shock or fire. Contact an authorized the service center for repair.

Avoid high temperatures and humidity.

Important Precautions

On Cleaning

Unplug the display before cleaning the face of the display screen. Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the display

screen because over-spraying may cause electrical shock.

When cleaning the product, unplug the power cord and scrub gently with a soft

cloth to prevent scratching. Do not clean with a wet cloth or spray water or other liquids directly onto the product. An electric shock may occur. (Do not use chemicals such as benzene, paint thinners or alcohol)

Spray water onto a soft cloth 2 to 4 times, and use it to clean the front frame;

wipe in one direction only. Too much moisture may cause staining.

On Repacking

Do not throw away the carton and packing materials. They make an ideal container in which to transport the unit. When shipping the unit to another location, repack it in its original material.

On Disposal

The fluorescent lamp used in this product contains a small amount of mercury. Do not dispose of this product with general household waste. Disposal of this product must be carried out in accordance to the regulations of

your local authority.

Accessories

!!! Thank for selecting LGE products !!!

Please make sure the following items are included with your monitor. If any items are missing, contact your dealer.

OWNER'S MANUAL/Cards

DVI-D Signal Cable

(This feature is not available in

all countries.)

AC-DC adapter

NOTE

This accessories may look different from those shown here. User must use shielded signal interface cables (D-sub 15 pin cable, DVI-D cable) with ferrite cores to maintain standard compliance for the product.

Power Cord

15-pin D-Sub Signal Cable

(To set it up, this signal cable may be

attached to this product before

shipping out.)

Connecting the Display

Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off.

Connecting the stand

1. Place the monitor face down on the cushion or soft cloth.

2. Assemble the stand base into the standbody in the correct direction as shown in the picture.

Stand Body

Stand Base

3. Attach the monitor to the stand base by turning the screw to the right.

4. Once assembled take the monitor up carefully and face the front side.

Screw : Turn the

screw by using the screw handle.

Connecting the Display

5. Turn the screw to the left to separate the stand body

from the stand base.

IMPORTANT

This illustration depicts the general model of connection. Your monitor may differ from the items shown in the picture. Do not carry the product upside down holding only the stand base. The product may fall and get damaged or injure your foot.

Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off.

Positioning your display

Adjust the position of the panel in various ways for maximum comfort.

Tilt Range : -5˚ to 10˚

IMPORTANT

It is recommended that in order to maintain an ergonomic and comfortable viewing position, the forward tilt angle of the monitor should not exceed 5 degrees. When adjusting the angle of the screen, do not put your finger(s) in between the head of the monitor and the stand body. You can hurt your finger(s).

Connecting the Display

Connecting with the PC

1. Before setting up the monitor, ensure that the power to the monitor, the computer

system, and other attached devices is turned off.

Connect signal input cable and power cord in order, then tighten the screw of the signal cable.

Connect DVI-D(Digital signal) Cable

Connect D-sub(Analog signal) Cable Connect HDMI Cable

AV equipment

(Set-Top Box, DVD, Video, Video Game Console)

* HDMI is optimized on the AV equipment. * Not supported PC

Wall-outlet type

Varies according to model.

Headphone/Earphone Input

DVI-D (This feature is not available in all countries.)

When using a D-Sub signal input cable connector for Macintosh

Mac adapter : For Apple Macintosh use, a

separate plug adapter is needed to change the 15 pin high density (3 row) D-sub VGA connector on the supplied cable to a 15 pin 2 row connector.

NOTE

This is a simplified representation of the rear view.

This rear view represents a general model; your display may differ from the view as shown.

Connecting the Display

Connecting with the PC

3. Press the power button on the front panel to turn the power on. When monitor power is

turned on, the 'Self Image Setting Function' is executed automatically.

(Only Analog Mode)

E2280V/E2380V

Power Button

E2280VX/E2380VX

Power Button

NOTE

‘ Self Image Setting Function’? This function provides the user with optimal display

settings.When the user connects the monitor for the first time, this function automatically adjusts the display to optimal settings for individual input signals.

‘AUTO’ Function? When you encounter problems such as blurry screen, blurred letters,

screen flicker or tilted screen while using the device or after changing screen resolution, press the AUTO function button to improve resolution.

Control Panel Functions

Front Panel Controls

E2280V/E2380V

E2280VX/E2380VX

MENU Button

SMART+ Button

OSD LOCKED/UNLOCKED

This function allows you to lock the current control settings, so that they cannot be inadvertently changed. Press and hold the MENU button for several seconds. The message "OSD LOCKED" should appear.

You can unlock the OSD controls at any time by pushing the MENU button for several seconds. The message "OSD UNLOCKED" should appear.

Use this button to enter ORIGINAL RATIO, FENGINE, DUAL WEB,CINEMA MODE menus. For more information, refer to page 22 to 30.

Control Panel Functions

SUPER+ RESOLUTION Button

AUTO Button

INPUT Button

(SOURCE Hot key)

For more information, refer to page 31 to 34.

E2280V / E2380V

AUTO IMAGE ADJUSTMENT

When adjusting your display settings, always press the AUTO button before entering the On Screen Display(OSD). (Only Analog Mode)

This will automatically adjust your display image to the ideal settings for the current screen resolution size (display mode).

The best display mode is

1920 x 1080

Use this button to select source from input.

When two input signals at least are connected, you can select the input signal (D-SUB/DVI/HDMI) you want. When only one signal is connected, it is automatically detected. The default setting is D-Sub.

E2280VX / E2380VX

EXIT Button

Power Button & Power Indicator

Exit the OSD(On Screen Display).

Use this button to turn the display on or off.

From front view,the power indicator stays purple if the display is running properly (On Mode). If the display is in Sleep Mode (Energy Saving), the power indicator is blinking purple.

On Screen Display (OSD) Control Adjustment

E2280V / E2380V

Screen Adjustment

Making adjustments to the image size, position and operating parameters of the display is quick and easy with the On Screen Display Control system. A short example is given below to familiarize you with the use of the controls. The following section is an outline of the available adjustments and selections you can make using the OSD.

To make adjustments in the On Screen Display, follow these steps:

Press the discretionary Button, then the main menu of the OSD appears.

To access a control, use the corresponding Buttons.

Use the / Buttons to adjust the image to the desired level.

Use the Button to select other sub-menu items.

Press the EXIT Button to exit from the OSD.

On Screen Display (OSD) Control Adjustment

E2280VX / E2380VX

Screen Adjustment

To make adjustments in the On Screen Display, follow these steps:

Press the discretionary Button, then the main menu of the OSD appears.

To access a control, use the corresponding Buttons.

Use the / Buttons to adjust the image to the desired level.

Use the Button to select other sub-menu items.

Press the EXIT Button to exit from the OSD.

On Screen Display(OSD) Selection and Adjustment

The following table indicates all the On Screen Display control, adjustment, and setting menus.

D-SUB

: D-SUB(Analog signal) input

DVI-D

: DVI-D(Digital signal) input

HDMI

: HDMI signal

Main menu Sub-menu

PICTURE

BRIGHTNESS CONTRAST SHARPNESS

BLACK LEVEL

COLOR

COLOR TEMP

(PRESET) (USER)

sRGB 6500K 7500K 8500K 9300K

RED GREEN BLUE

GAMMA

DISPLAY

HORIZONTAL VERTICAL

CLOCK PHASE

OVERSCAN

VOLUME

OTHERS

VOLUME

LANGUAGE POWER INDICATOR BUTTON INDICATOR

WHITE BALANCE

FACTORY RESET

SMART+

ORIGINAL RATIO

F-ENGINE

WIDE ORIGINAL

NORMAL MOVIE INTERNET DEMO

STANDARD MOVIE GAME

SPORTS DUAL WEB CINEMA MODE

Supported input

D-SUB

DVI-D HDMI

HDMI

D-SUB

DVI-D HDMI

D-SUB

To adjust the brightness, contrast and sharpness of the screen

To customize the color of the screen

To adjust the position of the screen

D-SUB

To improve the clarity and stability of the screen

HDMI

D-SUB

DVI-D HDMI

D-SUB

DVI-D HDMI

D-SUB

DVI-D HDMI

D-SUB DVI-D

HDMI

D-SUB

DVI-D

To adjust the headphone/ earphone volume

To customize the screen status for a user's operating environment

To select or customize desired image settings

Description

On Screen Display(OSD) Selection and Adjustment

SUPER+ RESOLUTION

D-SUB

DVI-D HDMI

The image is inevitably damaged during the date processing to enlarge the image. SUPER+ RESOLUTION can maintain the resolution to show the clear video image even with the enlargement with the picture quality improvement technology that adjusts the blurred focus and rough outline due to the enlargement.

NOTE

The order of icons may differ depending on the model (13 to 34).

On Screen Display(OSD) Selection and Adjustment

E2280V / E2380V

You were introduced to the procedure of selecting and adjusting an item using the OSD system. Listed below are the icons, icon names, and icon descriptions of the all items shown on the Menu.

Press the MENU Button, then the main menu of the OSD appears.

Menu Name

Icons

Submenus

Exit Adjust (Decrease/Increase) Select another sub-menu

Move to the upper menu

NOTE

OSD (On Screen Display) menu languages on the monitor may differ from the manual.

Button Tip

+ 37 hidden pages