LG DU60PY10 Users manual

Owner’s Manual 15

• Component Input ports

To get better picture quality, connect a DVD player to the compo­nent input ports as shown below.

How to connect

Connect the audio and video cables from the external equip­ment's output jacks to the TV input jacks, as shown in the
figure.
When connecting the TV to external equipment, match the
jack colors (Video = yellow, Audio Left = white, and Audio
Right = red).

How to use

1. Select the input source with using the TV/VIDEO button on

the remote control. (If connected to A/V INPUT , select
Video input source).

2. Operate the corresponding external equipment. Refer to
external equipment operating the tv guide on screen system.

Component ports

on the TV

Y

P

B

PR

Video output ports
on DVD player

Y
Y
Y
Y

Pb

B-Y

Cb
P

B

Pr

R-Y

Cr
PR

How to connect

1. Connect the DVD video outputs (Y, PB, PR) to the COMPONENT (Y, PB, PR) INPUT jacks on the TV and connect the DVD
audio outputs to the AUDIO INPUT jacks on the TV, as shown in the figure.

2. If your DVD only has an S-Video output jack, connect this to the S-VIDEO input on the TV and connect the DVD audio outputs
to the AUDIO INPUT jacks on the TV, as shown in the figure.

Note: If your DVD player does not have component video output, use S-Video.

How to use

1. Turn on the DVD player, insert a DVD.

2. Use the TV/VIDEO or COMP/RGB/HDMI button on the remote control to select Component 1 or Component 2. (If connected
to S-VIDEO, select the Video or Front Video external input source.)

3. Refer to the DVD player's manual for operating instructions.

External

External

A/V Source Setup

A/V Source Setup

DVD Setup

DVD Setup

CABLE

Cable

ANTENNA

AC INPUT

RL

AUDIO VIDEO

DVI

COMPONENT2

DIGITAL AUDIO(OPTICAL)

VIDEO INPUT

AUDIO INPUT

HDMI /
DVI(VIDEO)

AC INPUTAC INPUT

B

R

(R) AUDIO (L)

DIGITAL AUDIO

OPTICAL

(R) AUDIO (L)

S-VIDEO

CABLE

Cable

ANTENNA

DVI

COMPONENT2

DIGITAL AUDIO(OPTICAL)

VIDEO INPUT

AUDIO INPUT

HDMI /
DVI(VIDEO)

DVD

or

Camcorder

Video Game Set

Notes:

• Digital Audio will not work for Component 1 input source.

• Digital Audio operation has priority if Digital Audio and AUDIO L/R
are connected at the same time.

or

16 Plasma TV

Installation

- This TV can receive Digital Over-the-air/Cable signals without an external digital set-top box. However, if you do receive Digital
signals from a digital set-top box or other digital external device, refer to the figure as shown below.

- This TV supports HDCP (High-bandwidth Digital Contents Protection) protocol for Digital Contents (480p,720p,1080i).

How to connect

Use the TV’s COMPONENT (Y, P

B, PR) INPUT, RGB or HDMI/DVI jack

for video connections, depending on your set-top box connector. Then,
make the corresponding audio connections.

How to use

1. Turn on the digital set-top box. (Refer to the owner’s manual for the
digital set-top box.)

2. Use TV/VIDEO or COMP/RGB/HDMI on the remote control to select
Component 1, Component 2, RGB-DTV, or HDMI/DVI source.

HDSTB Setup

HDSTB Setup

AC INPUT

(R) AUDIO (L)

RGB-DTV OUTPUT

B

R

(R) AUDIO (L)

DIGITAL AUDIO

OPTICAL

(R) AUDIO (L)

DVI-DTV OUTPUT

DIGITAL AUDIO

OPTICAL

DVI

COMPONENT2

DIGITAL AUDIO(OPTICAL)

VIDEO INPUT

AUDIO INPUT

HDMI /
DVI(VIDEO)

CABLE

Cable

ANTENNA

HDMI-DTV OUTPUT

Digital Set-top Box

or

or

or

or

Signal
480i
480p
720p
1080i

Component 1/2

Yes
Yes
Yes
Yes

RGB-DTV,HDMI/DVI

No
Yes
Yes
Yes

CableCARD

CableCARD

TM

TM

Setup

Setup

AC INPUT

CABLE

Cable

ANTENNA

How to use

Insert the CableCARD

TM

TM

received from Cable Service provider to

CableCARD

TM

TM

slot of TV back panel.

If Host or CableCARD

TM

TM

does not display on the screen, contact with Cable

service provider by phone.

Note :

• CableCARD

TM

TM

has the types of Motorola, Scientific Atlanta, SCM etc..

These 3 types of CableCARD

TM

TM

can be used for this PLASMA TV.

Caution: When removing the CableCARD

TM

TM

, do not
fall it as this may cause impact to the
CableCARD

TM

TM

.

Owner’s Manual 17

Installation

How to connect

1. To get the best picture quality, adjust the PC graphics card to 1024x768, 60Hz.

2. Use the TV’s RGB INPUT or HDMI/DVI (Digital Visual Interface) INPUT port for video connections, depending on your PC con­nector.

• If the graphic card on the PC does not output analog and digital RGB simultaneously, connect only one of either RGB INPUT

or DVI INPUT to display the PC on the TV.

• If the graphic card on the PC does output analog and digital RGB simultaneously, set the TV to either RGB or HDMI/DVI; (the

other mode is set to Plug and Play automatically by the TV.)

3. Then, make the corresponding audio connections. If using a sound card, adjust the PC sound as required.

How to use

1. Turn on the PC and the TV.

2. Turn on the display by pressing the POWER button on the TV's remote control.

3. Select RGB-PC or HDMI/DVI input source in main input option of SETUP menu. (Refer to P.59)

4. Check the image on your TV. There may be noise associated with the resolution, vertical pattern, contrast or brightness in PC
mode. If noise is present, change the PC mode to another resolution, change the refresh rate to another rate or adjust the
brightness and contrast on the menu until the picture is clear. If the refresh rate of the PC graphic card can not be changed,
change the PC graphic card or consult the manufacturer of the PC graphic card.

Notes: • Depending on the graphics card, DOS mode may not work if you use a HDMI to DVI cable.

• Avoid keeping a fixed image on the TV's screen for a long period of time. The fixed image may become permanently
imprinted on the screen. Use the Orbiter screen saver when possible.

• The synchronization input form for Horizontal and Vertical frequencies is separate.

PC Setup

PC Setup

AC INPUT

DVI

COMPONENT2

DIGITAL AUDIO(OPTICAL)

VIDEO INPUT

AUDIO INPUT

HDMI /
DVI(VIDEO)

CABLE

Cable

ANTENNA

- This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings.

- The TV perceives 640x480, 60Hz as DTV 480p based on the PC graphic card, change the screen scanning rate for the graphic
card accordingly.

Resolution

640x350

720x400

640x480

800x600

Horizontal

Frequency(KHz)

31.468

37.861

31.469

37.927

31.469

37.861

37.500

43.269

70.09

85.08

70.08

85.03

59.94

72.80

75.00

85.00

35.156

37.879

48.077

46.875

53.674

48.363

56.476

60.023

56.25

60.31

72.18

75.00

85.06

60.00

70.06

75.02

Vertical

Frequency(Hz)

Resolution

Horizontal

Frequency(KHz)

Vertical

Frequency(Hz)

1024x768

Monitor Display Specifications (RGB-PC )