LG Electronics DU-42PX12XD User Manual

PLASMA TV

OWNER’S MANUAL

Please read this manual carefully and completely before
operating your TV.
Retain this manual for future reference.
Record model number and serial number of the TV in the
spaces provided below.
See the label attached on the back cover and relate this
information to your dealer if you require service.

Model Number :
Serial Number :

MODEL: DU-42PX12XD

LG Electronics U.S.A., Inc.

2 Plasma TV

Warning/Caution

WARNING/CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER
SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to

the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of suffi­cient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of

important operating and maintenance (servicing) instructions in the literature accompanying the appli­ance.

WARNING/CAUTION:

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

FCC NOTICE

• A Class B digital device

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

• Any changes or modifications not expressly approved by the party responsible for compli­ance could void the user’s authority to operate the equipment.

.

CAUTION:

Do not attempt to modify this product in any way without written authorization from LG Electronics. Unauthorized mod­ification could void the user’s authority to operate this product.

COMPLIANCE:

The responsible party for this product’s compliance is:
LG Electronics U.S.A., Inc
1000 Sylvan Avenue, Englewood Cliffs, NJ 07632
1-800-243-0000
http://www.lgusa.com

WARNING

RISK OF ELECTRIC SHOCK
DO NOT OPEN

/CAUTION

WARNING/CAUTION

TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO
RAIN OR MOISTURE.

W

W

arning/Caution

arning/Caution

Owner’s Manual 3

Safety Instructions

IMPORTANT SAFETY INSTRUCTIONS

Important safety instructions shall be provided with each apparatus. This information shall be given in a separate booklet or
sheet, or be located before any operating instructions in an instruction for installation for use and supplied with the appara­tus. This information shall be given in a language acceptable to the country where the apparatus is intended to be used. The
important safety instructions shall be entitled “Important Safety Instructions”. The following safety instructions shall be includ­ed where applicable, and, when used, shall be verbatim as follows. Additional safety information may be included by adding
statements after the end of the following safety instruction list. At the manufacturer’s option, a picture or drawing that illus­trates the intent of a specific safety instruction may be placed immediately adjacent to that safety instruction :

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampli-

fiers)that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with

one wider than the other. A grounding type plug has two blades and a third grounding prong, The wide blade or the

third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for

replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the

point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus.

When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

Safety Instructions

Safety Instructions

PORTABLE CART WARNING

4 Plasma TV

Safety Instructions

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged

in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into

the apparatus, the apparatus has exposed to rain or moisture, does not operate normally, or has been dropped.

15. CAUTION concerning the Power Cord :

Most appliances recommend they be placed upon a dedicated circuit; that

is, a single outlet circuit which powers only that appliance and has no

additional outlets or branch circuits. Check the specification page of

this owner's manual to be certain.

Do not overload wall outlets. Overloaded wall outlets, loose or damaged

wall outlets, extension cords, frayed power cords, or damaged or

cracked wire insulation are dangerous. Any of these conditions could

result in electric shock or fire. Periodically examine the cord of your

appliance, and if its appearance indicates damage or deterioration,

unplug it, discontinue use of the appliance, and have the cord replaced

with an exact replacement part by an authorized servicer.

Protect the power cord from physical or mechanical abuse, such as being

twisted, kinked, pinched, closed in a door, or walked upon. Pay

particular attention to plugs, wall outlets, and the point where the

cord exits the appliance.

16. Outdoor Use Marking :

WARNING - To Reduce The Risk Of Fire Or Electric Shock, Do Not Expose This Appliance To Rain Or Moisture.

17. Wet Location :

Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall

be placed on the apparatus.

Safety Instructions

Safety Instructions

Owner’s Manual 5

Contents

After reading this manual, keep it handy for future reference.

Warning/Caution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3~4

Introduction

Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Connection Options . . . . . . . . . . . . . . . . . . . . . .8

Remote Control Key Functions . . . . . . . . . . . . . .9

Installation

Installation Instruction . . . . . . . . . . . . . . . . . . .10~11

External Equipment Connections . . . . . . . . . .12~16

Antenna Connection . . . . . . . . . . . . . . . . . . . . .12

VCR Setup / Cable TV Setup . . . . . . . . . . . . . .13

External A/V Source Setup . . . . . . . . . . . . . . . .14

DVD Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

HDSTB Setup / Digital Audio Output . . . . . . . . .15

PC Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Operation

Screen Setup for PC mode . . . . . . . . . . . . . . . . . .17

Turning the TV On . . . . . . . . . . . . . . . . . . . . . . . .18

On-screen Menus Language Selection . . . . . . . . .18

Setup Menu Options

EZ Scan (Channel Search) . . . . . . . . . . . . . . . .19

Channel Edit . . . . . . . . . . . . . . . . . . . . . . . . . . .19

DTV Signal Strength . . . . . . . . . . . . . . . . . . . . .20

Channel Label Setup . . . . . . . . . . . . . . . . . . . .20

Main Picture Source Selection . . . . . . . . . . . . .20

Video Menu Options

EZ Picture . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Manual Picture Control (Off Option) . . . . . . . . .21

Color Temperature Control . . . . . . . . . . . . . . . .21

Video Preset . . . . . . . . . . . . . . . . . . . . . . . . . .21

Audio Menu Options

Audio Language . . . . . . . . . . . . . . . . . . . . . . . .22

EZ SoundRite / EZ Sound . . . . . . . . . . . . . . . . .22

Manual Sound Control (Off Option) . . . . . . . . . .23

Stereo/SAP Broadcasts Setup . . . . . . . . . . . . .23

Front Surround . . . . . . . . . . . . . . . . . . . . . . . . .23

TV Speakers On/Off Setup . . . . . . . . . . . . . . . .24

BBE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

Time Menu Options

Auto Clock Setup . . . . . . . . . . . . . . . . . . . . . . .25

Manual Clock Setup . . . . . . . . . . . . . . . . . . . . .25

On/Off Timer Setup . . . . . . . . . . . . . . . . . . . . .25

Sleep Timer / Auto Off . . . . . . . . . . . . . . . . . . . .26

Option Menu Features

Aspect Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Caption / Caption Mode . . . . . . . . . . . . . . . . . .28

Caption Option . . . . . . . . . . . . . . . . . . . . . . . .29

Cinema Mode Setup . . . . . . . . . . . . . . . . . . . .29

Demo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

ISM Method . . . . . . . . . . . . . . . . . . . . . . . . . . .30

Low power . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

Split Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

Lock Menu Options

Parental Lock Setup . . . . . . . . . . . . . . . . . . . . .32

PIP (Picture-in-Picture)/Twin Picture

Watching PIP/Twin Picture . . . . . . . . . . . . . . . ..33

Selecting an Input Signal Source for PIP/Twin Picture

. .33

Swapping the PIP/Twin Picture . . . . . . . . . . . . .33

TV Program Selection for PIP . . . . . . . . . . . . . .33

Moving the PIP sub picture . . . . . . . . . . . . . . . .34

Adjusting Main and Sub Picture Sizes for Twin Picture . .34

External Control Device Setup . . . . . . . . . . . . . . . .35~39

IR Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40~41

Programming the Remote . . . . . . . . . . . . . . . . . . . . . .42

Programming Codes . . . . . . . . . . . . . . . . . . . . . . .43~44

Troubleshooting Checklist . . . . . . . . . . . . . . . . . . . . . .45

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46

Product Specifications . . . . . . . . . . . . . . . . . . . . . . . . .46

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47~48

Contents

Contents

Setup and Operation Checklist

Setup and Operation Checklist

Setup and Operation Checklist
(See pages 11~16 for available connection and operational setup options.)

1. Unpack TV and all accessories.

2. Connect all external video and audio equipment.
see pages 14 ~ 16.

3 Install batteries in remote control.

See page 9.

4. Turn TV on.
See page 18.

5. Turn video source equipment on.

6. Select viewing source for TV.
See page 20.

7. Fine-tune source image and sound to your personal prefer­ence or as required by source.
See pages 21 ~ 24.

8. Additional features set up
See Contents above.

6 Plasma TV

Introduction

Introduction

Introduction

What is a Plasma Display Panel (PDP)?

A plasma display panel is the latest display technology and the best way to achieve flat panel displays with excellent image quality
and large screen sizes that are easily viewable. The PDP can be thought of as a descendant of the neon lamp and it can be also
be viewed as a series of fluorescent lamps.

How does it work?

PDP is an array of cells, known as pixels, which are comprised of 3 sub pixels, corresponding to the colors red, green, and blue.
Gas in a plasma state is used to react with phosphors in each sub-pixel to produce colored light (red, green, or blue). These phos­phors are the same types used in Cathode Ray Tube (CRT) devices such as televisions and common computer monitors.

You get the rich, dynamic colors that you expect. Each sub-pixel is individually controlled by advanced electronics to produce over
16 million different colors. All of this means that you get perfect images that are easily viewable in a display that is less than 5
inches thick.

160° - Wide angle range of vision

Your flat panel plasma screen offers an exceptionally broad viewing angle -- over 160 degrees. This means that the display is
clear and visible to viewers anywhere in the room who can see the screen.

Wide Screen

The screen of the Plasma Display is so wide that your viewing experience is as if you are in a theater.

Multimedia

Connect your plasma display to a PC and you can use it for conferencing, games, and Internet browsing. The Picture-in-Picture
feature allows you to view your PC and video images simultaneously.

Versatile

The light weight and thin size makes it easy to install your plasma display in a variety of locations where conventional TVs will not
fit.

The PDP Manufacturing Process: a few minute colored dots may be present on the PDP screen

The PDP (Plasma Display Panel), which is the display device of this product is composed of 0.9 to 2.2 million cells. A few cell
defects will normally occur in the PDP manufacturing process. Several tiny, minute colored dots visible on the screen should be
acceptable. This also occurs in other PDP manufacturers' products. The tiny dots appearing does not mean that this PDP is defec­tive. Thus a few cell defects are not sufficient cause for the PDP to be exchanged or returned. Our production technology mini­mizes these cell defects during the manufacture and operation of this product.

Owner’s Manual 7

Introduction

Controls

Controls

- This is a simplified representation of front panel.
Image shown may be somewhat different from your TV.

Front Panel Controls

Front Panel Controls

POWER Button

Remote Control Sensor

VOLUME (

F,G) Buttons

Power Standby Indicator

Illuminates red in standby mode,
Illuminates green when the TV is
turned on.

CHANNEL (E, D) Buttons

MENU Button

TV/VIDEO Button

TV/VIDEO

MENU

VOL CH

8 Plasma TV

Introduction

Connection Options

Connection Options

R

S-VIDEO VIDEO

L / MONO

AUDIO

A/V 2

REMOTE

CONTROL

RS-232C INPUT

(CONTROL/SERVICE)

AC INPUT

AUDIO INPUT

COMPONENT 2

COMPONENT 1

RL

DIGITAL AUDIO

(OPTICAL)

DVI

INPUT

COMPONENT1
INPUT

OUTPUT

AUDIO INPUT

DVI INPUT
(PC/DTV INPUT)

RGB INPUT

(PC/DTV INPUT)

VIDEO INPUT

DVD
/DTV
INPUT

A/V

INPUT 1

AUDIO

R L

(MONO)

VIDEO

S-VIDEO

Antenna
Analog/DTV

Back Connection Panel

Back Connection Panel

Antenna Inputs

Connect cable or antenna signals to the

TV, either directly or through your cable

box.

DVI Input/Audio Input/RGB
Input

Connect the monitor output con­nector from a PC to the appro­priate input port.

Digital Audio (DVI: Digital Visual

Interface/Component1) Input/

Digital Audio Output

Connect digital audio from various types

of equipment. Note: In standby mode,

these ports will not work.

Audio/Video Input 1

Connect audio/video out-

put from an external

device to these jacks.

DVD/DTV Input (Component
1-2)

Connect a component
video/audio device to these
jacks.

Remote Control
Port

Connect your wired
remote control here.

S-Video Input

Connect S-Video out from an
S-VIDEO device to the S­VIDEO input.

Power Cord Socket

This TV operates on an AC power. The voltage is indi-

cated on the Specifications page. Never attempt to oper-

ate the TV on DC power.

S-VIDEO Input

A connection available to provide better
picture quality than the video input.

VIDEO Input

Connects the video signal from a video
device.

AUDIO Input

Use to connect to hear stereo sound
from an external device.

RS-232C INPUT
(CONTROL/SERVICE) PORT

Connect to the RS-232C port
on a PC.

Owner’s Manual 9

Installation

- When using the remote control, aim it at the remote control sensor on the TV.

LIGHT

TV/VIDEO

MODE

COMP/RGB/DVI

MUTE

SURF

VOL CH

INFO

SAP

RATIO

CC

MENU

SOUND VIDEO

EXIT

PLAY PAUSE STOP RECORD

PIP PIPCH- PIPCH+ PIPINPUT

FREEZE

ADJUST

OK

ZOOM SIGNAL SWAP

REW FF SKIP

POWER

TIM

ER

FLASHBK

LIGHT

Illuminates the remote control buttons.

TV/VIDEO

Selects: DTV, Analog, Video1-2,

Component 1-2, RGB-DTV (or RGB-PC),

DVI-DTV (or DVI-PC) input sources.

COMP/RGB/DVI

Selects: Component 1-2, RGB-DTV (or

RGB-PC), DVI-DTV (or DVI-PC) input

sources.

NUMBER buttons

DASH

Used to enter a program number for multi-

ple program channels such as 2-1,2-

2,etc.

MUTE

Switches the sound on or off.

VCR/DVD BUTTONS

Control some video cassette recorders or
DVD player ("RECORD" button will not
work on a DVD player).

RATIO

Changes the aspect ratio.

MODE

Selects the remote operating mode: TV,
VCR, DVD, CABLE, HDSTB or AUDIO.
Select other operating modes, for the
remote to operate external devices.

POWER

Turns your TV or any other programmed
equipment on or off, depending on mode.

TIMER

Lets you select the amount of time before
your TV turns itself off automatically.

SURF

Use to scroll the Surf channel list.

CC

Select a closed caption:
Off, EZ Mute, and On.

FLASHBK

Tunes to the last channel viewed.

THUMBSTICK (Up/Down/Left/Right/OK)

Allows you to navigate the on-screen

menus and adjust the system settings to

your preference.

CHANNEL UP/DOWN

Selects available channels found
during EZ scan.

EXIT

Clears all on-screen displays and returns to
TV viewing from any menu.

VIDEO

Adjusts the factory preset picture according
to the room.

VOLUME UP/DOWN

Increases/decreases the sound level.

SAP

Selects MTS sound: Mono, Stereo, and

SAP. Change the audio language in DTV

mode.

MENU

Brings up the main menu to the screen.

INFO

When you watch the TV, displays informa-

tion on top of the screen. Not available in

Component 1-2, RGB and DVI mode.

SOUND

Selects the sound appropriate

for the program's character.

PIP

Switches between PIP and Twin picture
modes.

PIPCH-/PIPCH+

Changes to next higher/lower PIP channel.

PIP INPUT

Selects the input source for the sub picture.

SWAP

Exchanges the PIP/main images.

FREEZE

Freezes the currently-viewed picture. Main

picture is frozen in PIP/Twin picturre mode.

ADJUST

Adjusts screen position, clock, and

phase in PC mode.

ZOOM

Enlarges the main picture size.

SIGNAL

Displays the digital signal strength.

Installing Batteries

• Open the battery compartment cover on the back side and install the batteries
matching correct polarity (+ with +, - with -).

• Install two 1.5V AA batteries. Don’t mix old or used batteries with new ones.
Close the battery cover.

Remote Control Key Functions

Remote Control Key Functions

10 Plasma TV

Installation

Installation

Installation

Owner’s Manual

1.5V

1.5V

Batteries

Power Cord

L

I

G

H

T

T

V

/

V

I

D

E

O

MODE

COMP/RGB/DVI

MUTE

SURF

VOL CH

INFO

SAP

RATIO

CC

MENU

SOUNDVIDEO

EXIT

PLAY PAUSE STOPRECORD

PIP PIPCH- PIPCH+ PIPINPUT

FREEZE

ADJUST

OK

ZOOM SIGNAL SWAP

REW FF SKIP

P
O
W
E

R

T
IM
E

R

FLASHBK

Remote Control

75Ω Round Cable

Ensure that the following accessories are included with your plasma display. If an accessory is missing, please contact the dealer
where you purchased the product.

- Secure the TV assembly by attaching it to a wall for additional support.

Attaching the

Attaching the

TV assembly to the wall

TV assembly to the wall

• If the set will be mounted on a desk top, insert
the 2 eye-bolts and tighten them securely in the upper
holes as shown.
Install the wall brackets on the wall with 2 bolts*, (not
supplied with the product), as shown.
Match the height of the eye-bolts and the wall brack­ets.
Check to be sure the eye-bolts and the brackets are
tightened securely.

• Secure the TV assembly to the wall with strong strings or
wire cables, (not supplied with the product), as shown.

2-Wall brackets

2-eye-bolts

D-sub 15 pin Cable

Owner’s Manual 11

Installation

Installation Instructions

Installation Instructions

• The TV can be installed in various ways such as on a wall, or on a desktop etc.

• The TV is designed to be mounted horizontally.

GROUNDING

Ensure that you connect the earth ground wire to prevent possible
electric shock. If grounding methods are not possible, have a qualified
electrician install a separate circuit breaker. Do not try to ground the
unit by connecting it to telephone wires, lightening rods, or gas pipes.

Power

Supply

Short-circuit

Breaker

WWall Mount: Horizontal installation

all Mount: Horizontal installation

For proper ventilation, allow a clearance of 4” on each
side and 2” from the wall. Detailed installation instruc­tions are available from your dealer, see the optional
Wall Mounting Bracket Installation and Setup Guide.

Desktop Pedestal Installation

Desktop Pedestal Installation

For proper ventilation, allow a clearance of 4” on each
side and the top, 2.36” on the bottom, and 2” from the
wall. Detailed installation instructions are included in
the optional Desktop Stand Installation and Setup
Guide available from your dealer.

To Mount on a Wall

Wall mount minimum allowable clearances for ade­quate ventilation.

To Install on a Desktop

Pedestal mount minimum allowable clearances for
adequate ventilation.

4 inches

4 inches4 inches

4 inches

2 inches

4 inches

4 inches

4 inches

2.36 inches

2 inches

12 Plasma TV

Installation

- Antenna or Cable Service without a Cable Box Connections

- For optimum picture quality, adjust antenna direction if needed.

Antenna Connection

Antenna Connection

Analog and Digital TV signals provided on one antenna

NOTE: If you are not sure of the type of signal(s) you are receiving, let EZ Scan complete all the channel signal-type searches.

The TV will let you know when the analog, cable, and digital channel scans are complete.

Analog and DTV signals provided on two separate antennas

• In a poor signal area to improve picture quality, purchase
and install a signal amplifier.

• If the antenna needs to be split for two TV’s, install a “2­Way Signal Splitter” in the connections.

• If the antenna is not installed properly, contact your deal­er for assistance.

Multi-family Dwellings/Apartments
(Connect to wall antenna socket)

Single-family Dwellings /Houses
(Connect to wall jack for outdoor antenna)

Outdoor
Antenna

Wall Antenna
Socket

VHF Antenna

UHF Antenna

RF Coaxial Wire (75 ohm)

Copper Wire

Turn clockwise to tighten.

Copper Wire

Be careful not to bend the Copper wire when
connecting the antenna.

T

Wall Antenna
Socket

RF Coaxial Wire (75 ohm)

Analog Antenna

Digital Antenna

Copper Wire

Copper Wire

Turn clockwise to tighten.

Wall Antenna
Socket

RF Coaxial Wire (75 ohm)

External Equipment Connections

External Equipment Connections

AC INPUT

Antenna
Analog/DTV

S-VIDEO

Antenna
Analog/DTV

AC INPUT

(MONO)

1

R L

VIDEO

AUDIO

Signal

Amplifier

S-VIDEO

Antenna
Analog/DTV

(MONO)

1

R L

VIDEO

AUDIO

AC INPUT

Owner’s Manual 13

Installation

NOTE: All cables shown are not included with the TV

- To avoid picture noise (interference), leave an adequate distance between the VCR and TV

- Use the ISM Method (on the Option menu) feature to avoid having a fixed image remain on the screen for a long period of time.
Typically a frozen still picture from a VCR. If the 4:3 picture format is used; the fixed images on the sides of the screen may
remain visible on the screen.

Connection Option 1

Set VCR output switch to 3 or 4 and then tune

TV to the same channel number.

Connection Option 2

1. Connect the audio and video cables from the
VCR's output jacks to the TV input jacks, as
shown in the figure.
When connecting the TV to a VCR, match the
jack colors (Video = yellow, Audio Left = white,
and Audio Right = red).
If you connect the S-VIDEO output from a VCR
to the S-VIDEO input, the picture quality is
improved; compared to connecting the Video
input.

2. Insert a video tape into the VCR and press
PLAY on the VCR. (Refer to the VCR owner’s
manual.)

3. Select the input source by using the TV/VIDEO
button on the remote control. (If connected to
A/V INPUT 1, select Video 1 input source)

Do not connect to both Video and
S-Video at the same time.

VCR Setup

VCR Setup

AC INPUT

AUDIO INPUT

COMPONENT 2

COMPONENT 1

RL

AUDIO INPUT

DVI INPUT
(PC/DTV INPUT)

RGB INPUT

(PC/DTV INPUT)

VIDEO INPUT

A/V

INPUT 1

(MONO)

VIDEO

S-VIDEO

Antenna
Analog/DTV

S-VIDEO

OUT

IN

(R) AUDIO (L) VIDEO

34

OUTPUT
SWITCH

ANT OUT

ANT IN

AUDIO

R L

DVD
/DTV
INPUT

- After subscribing to a cable TV service from a local provider and installing a converter, you can watch cable TV programming.
The TV cannot display TV programming unless a TV tuner device or cable TV converter box is connected to the TV.

- For further information regarding cable TV service, contact your local cable TV service provider(s).

Connection Option 1

1. Select 3 or 4 with channel switch on the cable
box.

2. Tune the TV channel to the same selected
output channel on cable box.

3. Select channels at the cable box or with the
cable box remote control.

Connection Option 2

1. Connect the audio and video cables from the
Cable Box's output jacks to the TV input jacks,
as shown in the figure.
When connecting the TV to a Cable Box,
match the jack colors (Video = yellow, Audio
Left = white, and Audio Right = red).

2. Select the input source by using the
TV/VIDEO button on the remote control. (If
connected to A/V INPUT 1, select Video 1
input source)

3. Select your desired channel with the remote
control for cable box.

Cable

Cable

TV Setup

TV Setup

AC INPUT

AUDIO INPUT

COMPONENT 2

COMPONENT 1

RL

IO INPUT

RGB INPUT

(PC/DTV INPUT)

VIDEO INPUT

A/V

INPUT 1

(MONO)

VIDEO

S-VIDEO

Antenna
Analog/DTV

TV

VCR

RF Cable

(R) AUDIO (L) VIDEO

34

OUTPUT
SWITCH

DVD
/DTV
INPUT

AUDIO

R L

VCR

Cable Box

1

2

1

2

14 Plasma TV

Installation

• Component Input ports

To get better picture quality, connect a DVD player to the compo­nent input ports as shown below.

How to connect

Connect the audio and video cables from the external equip­ment's output jacks to the TV input jacks, as shown in the
figure.
When connecting the TV to external equipment, match the
jack colors (Video = yellow, Audio Left = white, and Audio
Right = red).

How to use

1. Select the input source by using the TV/VIDEO button on

the remote control. (If connected to A/V INPUT 1, select
Video 1 input source).

2. Operate the corresponding external equipment. Refer to
external equipment operating guide.

Component ports

on the TV

Y PB

PR

Video output ports
on DVD player

Y
Y
Y
Y

Pb

B-Y

Cb
PB

Pr

R-Y

Cr
P

R

How to connect

1. Connect the DVD video outputs (Y, P

B, PR

) to the COMPONENT (Y,

P

B, PR) INPUT jacks on the TV and connect the DVD audio outputs

to the AUDIO INPUT jacks on the TV, as shown in the figure.

2. If your DVD only has an S-Video output jack, connect this to the S­VIDEO input on the TV and connect the DVD audio outputs to the
AUDIO INPUT jacks on the TV, as shown in the figure.

NOTE: If your DVD player does not have component video output, use

S-Video.

How to use

1. Turn on the DVD player, insert a DVD.

2. Use the TV/VIDEO or COMP/RGB/DVI button on the remote control
to select Component 1 or Component 2. (If connected to S­VIDEO, select the Video 1 or Video 2 external input source.)

3. Refer to the DVD player's manual for operating instructions.

External

External

A/V Source Setup

A/V Source Setup

DVD Setup

DVD Setup

RL

AUDIO VIDEO

AC INPUT

AUDIO INPUT

COMPONENT 2

COMPONENT 1

RL

NPUT

VIDEO INPUT

A/V

INPUT 1

(MONO)

VIDEO

Antenna
Analog/DTV

S-VIDEO

DVD
/DTV
INPUT

AUDIO

R L

REMOTE

CONTROL

RS-232C INPUT

(CONTROL/SERVICE)

AUDIO INPUT

COMPONENT 2

COMPONENT 1

RL

DIGITAL AUDIO
(OPTICAL)

DVI

INPUT

COMPONENT1
INPUT

OUTPUT

VIDEO INPUT

A/V

INPUT 1

(MONO)

VIDEO

Antenna 1
Analog/DTV

Ante
D

B

R

(R) AUDIO (L)

DIGITAL AUDIO

OPTICAL

(R) AUDIO (L)

S-VIDEO

S-VIDEO

DVD
/DTV
INPUT

AUDIO

R L

DVD

or

Camcorder

Video Game Set

NOTES

• Digital Audio will not work for Component 2 input source.

• Digital Audio operation has priority if Digital Audio and AUDIO L/R

are connected at the same time.

or

Owner’s Manual 15

Installation

Send the TV’s audio to external audio equipment (stereo system) via
the Digital Audio Output Optical port.

How to connect

1. Connect one end of an optical cable to the TV Digital Audio Optical
Output port.

2. Connect the other end of the optical cable to the digital audio optical
input on the audio equipment.

See the external audio equipment instruction manual for operation.

Caution: Do not look into the optical output port.

Looking at the laser beam may damage
your vision.

Digital

Digital

Audio Output

Audio Output

- This TV can receive Digital Over-the-air/Cable signals without an external digital set-top box. However, if you do receive Digital
signals from a digital set-top box or other digital external device, refer to the figure as shown below.

- This TV supports HDCP (High-bandwidth Digital Contents Protection) protocol for DTV (480p,720p,1080i) mode.

How to connect

Use the TV’s COMPONENT (Y, PB, PR) INPUT, RGB or DVI jack for
video connections, depending on your set-top box connector. Then,
make the corresponding audio connections.

How to use

1. Turn on the digital set-top box. (Refer to the owner’s manual for the
digital set-top box.)

2. Use TV/VIDEO or COMP/RGB/DVI on the remote control to select
Component 1, Component 2, RGB-DTV, or DVI-DTV source.

HDSTB Setup

HDSTB Setup

REMOTE

CONTROL

RS-232C INPUT

(CONTROL/SERVICE)

AC INPUT

AUDIO INPUT

COMPONENT 2

COMPONENT 1

RL

DIGITAL AUDIO

(OPTICAL)

DVI

INPUT

COMPONENT1
INPUT

OUTPUT

AUDIO INPUT

DVI INPUT
(PC/DTV INPUT)

RGB INPUT

(PC/DTV INPUT)

VIDEO INPUT

A/V

INPUT 1

(MONO)

VIDEO

Antenna
Analog/DTV

(R) AUDIO (L)

RGB-DTV OUTPUT

B

R

(R) AUDIO (L)

DIGITAL AUDIO

OPTICAL

(R) AUDIO (L)

DVI-DTV OUTPUT

DIGITAL AUDIO

OPTICAL

S-VIDEO

DVD
/DTV
INPUT

AUDIO

R

L

Digital Set-top Box

or

or

or

or

REMOTE

CONTROL

RS-232C INPUT

(CONTROL/SERVICE)

AUDIO INPUT

COMPONEN

COMPONEN

RL

DIGITAL AUDIO

(OPTICAL)

DVI

INPUT

COMPONENT1
INPUT

OUTPUT

AUDIO INPUT

DVI INPUT
(PC/DTV INPUT)

RGB INPUT

(PC/DTV INPUT)

Signal
480i
480p
720p
1080i

Component 1/2

Yes
Yes
Yes
Yes

RGB-DTV,DVI-DTV

No
Yes
Yes
Yes