PLASMA TV
OWNER’S MANUAL
MODEL: DU-42PX12XD
Please read this manual carefully and completely before operating your TV.
Retain this manual for future reference.
Record model number and serial number of the TV in the spaces provided below.
See the label attached on the back cover and relate this information to your dealer if you require service.
Model Number :
Serial Number :
LG Electronics U.S.A., Inc.
Warning
Warning
WARNING/CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING:
TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
POWER CORD POLARIZATION:
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
NOTE TO CABLE/TV INSTALLER:
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical.
REGULATORY INFORMATION:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
CAUTION:
Do not attempt to modify this product in any way without written authorization from LG Electronics. Unauthorized modification could void the user’s authority to operate this product.
COMPLIANCE:
The responsible party for this product’s compliance is: LG Electronics U.S.A., Inc
1000 Sylvan Avenue, Englewood Cliffs, NJ 07632
1-800-243-0000 http://www.lgusa.com
2 Plasma TV
Safety Instructions
Safety Instructions
Important safeguards for you and your new product
Your product has been manufactured and tested with your safety in mind. However, improper use can result in electrical shock or fire hazards. To avoid defeating the safeguards that have been built into your new product, please read and observe the following safety points when installing and using your new product, and save them for future reference.
Observing the simple precautions discussed in this manual can help you get many years of enjoyment and safe operation that are built into your new product.
This product complies with all applicable U.S. Federal safety requirements, and those of the Canadian Standards Association.
1. Read Instructions |
9. Attachments |
All the safety and operating instructions should be read |
Do not use attachments not recommended by the product |
before the product is operated. |
manufacturer as they may cause hazards. |
2. Follow Instructions
All operating and use instructions should be followed.
3. Retain Instructions
The safety and operating instructions should be retained for future reference.
4. Heed Warnings
All warnings on the product and in the operating instructions should be adhered to.
5. Cleaning
Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
6. Water and Moisture
Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool.
7. Accessories, Carts, and Stands
Do not place this product on a slippery or tilted surface, or on an unstable cart, stand, tripod, bracket, or table. The product may slide or fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer.
8. Transporting Product
A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn.
10. Ventilation
Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.
11. Power Sources
This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions.
12. Power-Cord Polarization
This product is equipped with a three-wire grounding type plug, a plug having a third (grounding) pin. This plug will only fit into the grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug.
13. Power-Cord Protection
Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.
PORTABLE CART WARNING
Owner’s Manual 3
Safety Instructions
Safety Instructions continued
14. Outdoor Antenna Grounding
If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code (U.S.A.), ANSI/ NFPA 70 provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-dis- charge unit, connection to grounding electrodes, and requirements for the grounding electrode.
Example of Grounding According to National Electrical Code Instructions
Ground Clamp
|
|
|
|
Antenna Lead in Wire |
|
|
|
|
Antenna Discharge Unit |
|
|
|
|
(NEC Section 810-20) |
|
|
|
|
Grounding Conductor |
Electric Service |
|
|
|
(NEC Section 810-21) |
|
|
|
|
|
Equipment |
|
|
|
Ground Clamps |
|
|
|
|
|
|
|
|
|
Power Service Grounding |
|
|
|
|
Electrode System (NEC |
|
|
|
|
Art 250, Part H) |
NEC - National Electrical Code
15. Lightning
For added protection for this product (receiver) during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges.
16. Power Lines
An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.
17. Overloading
Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock.
18. Object and Liquid Entry
Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.
19. Servicing
Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
20. Damage Requiring Service
Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:
a.If the power-supply cord or plug is damaged.
b.If liquid has been spilled, or objects have fallen into the product.
c.If the product has been exposed to rain or water.
d.If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation.
e.If the product has been dropped or the cabinet has been damaged.
f.If the product exhibits a distinct change in performance.
21. Replacement Parts
When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.
22. Safety Check
Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition.
23. Wall or Ceiling Mounting
The product should be mounted to a wall or ceiling only as recommended by the manufacturer. The product may slide or fall, causing serious injury to a child or adult, and serious damage to the product.
24. Heat
The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.
4 Plasma TV
Contents
Contents
Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3~4
Introduction
Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Connection Options . . . . . . . . . . . . . . . . . . . . . .8
Remote Control Key Functions . . . . . . . . . . . . . .9
Installation
Installation Instruction . . . . . . . . . . . . . . . . . . .10~11
External Equipment Connections . . . . . . . . . .12~16
Antenna Connection . . . . . . . . . . . . . . . . . . . . .12
VCR Setup / Cable TV Setup . . . . . . . . . . . . . .13
External A/V Source Setup . . . . . . . . . . . . . . . .14
Monitor Out Setup / DVD Setup . . . . . . . . . . . .14
HDSTB Setup / Digital Audio Output . . . . . . . . .15
PC Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Operation
Screen Setup for PC mode . . . . . . . . . . . . . . . . . .17
Turning the TV On . . . . . . . . . . . . . . . . . . . . . . . .18
On-screen Menus Language Selection . . . . . . . . .18
Setup Menu Options
EZ Scan (Channel Search) . . . . . . . . . . . . . . . .19
Channel Edit . . . . . . . . . . . . . . . . . . . . . . . . . . .19
DTV Signal Strength . . . . . . . . . . . . . . . . . . . . .20
Channel Label Setup . . . . . . . . . . . . . . . . . . . .20
Main Picture Source Selection . . . . . . . . . . . . .20
Video Menu Options
EZ Picture . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Manual Picture Control (Off Option) . . . . . . . . .21
Color Temperature Control . . . . . . . . . . . . . . . .21
Video Preset . . . . . . . . . . . . . . . . . . . . . . . . . .21
Audio Menu Options
Audio Language . . . . . . . . . . . . . . . . . . . . . . . .22
EZ SoundRite / EZ Sound . . . . . . . . . . . . . . . . .22
Manual Sound Control (Off Option) . . . . . . . . . .23
Stereo/SAP Broadcasts Setup . . . . . . . . . . . . .23
Front Surround . . . . . . . . . . . . . . . . . . . . . . . . .23
TV Speakers On/Off Setup . . . . . . . . . . . . . . . .24
BBE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Time Menu Options
Auto Clock Setup . . . . . . . . . . . . . . . . . . . . |
. . . |
25 |
Manual Clock Setup . . . . . . . . . . . . . . . . . . |
. . . |
25 |
On/Off Timer Setup . . . . . . . . . . . . . . . . . . |
. . . |
25 |
Sleep Timer / Auto Off . . . . . . . . . . . . . . . . . |
. . . |
26 |
Option Menu Features |
|
|
Aspect Ratio . . . . . . . . . . . . . . . . . . . . . . . . |
. . . |
27 |
Caption / Caption Mode . . . . . . . . . . . . . . . |
. . . |
28 |
Caption Option . . . . . . . . . . . . . . . . . . . . . |
. . . |
29 |
Cinema Mode Setup . . . . . . . . . . . . . . . . . |
. . . |
29 |
Demo . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
. . . |
29 |
ISM Method . . . . . . . . . . . . . . . . . . . . . . . . |
. . . |
30 |
Low power . . . . . . . . . . . . . . . . . . . . . . . . . |
. . . |
30 |
Split Zoom . . . . . . . . . . . . . . . . . . . . . . . . . |
. . . |
30 |
Lock Menu Options |
|
|
Parental Lock Setup . . . . . . . . . . . . . . . . . . |
. . . |
32 |
PIP (Picture-in-Picture)/POP/Twin Picture |
|
|
Watching PIP/POP/Twin Picture . . . . . . . . . |
. . .. |
33 |
Selecting an Input Signal Source for PIP/Twin Picture . . |
33 |
|
Swapping the PIP/Twin Picture . . . . . . . . . . |
. . . |
33 |
TV Program Selection for PIP . . . . . . . . . . . |
. . . |
33 |
Moving the PIP sub picture . . . . . . . . . . . . . . |
. . |
34 |
Adjusting Main and Sub Picture Sizes for Twin Picture . . |
34 |
|
POP (Picture-out-of-Picture: Channel Scan) |
. . .34 |
|
External Control Device Setup . . . . . . . . . . . . . . . . |
35~39 |
|
IR Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
40~41 |
|
Programming the Remote . . . . . . . . . . . . . . . . . . . . |
. . |
42 |
Programming Codes . . . . . . . . . . . . . . . . . . . . . . .43~44
Troubleshooting Checklist . . . . . . . . . . . . . . . . . . . . . .45
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
Product Specifications . . . . . . . . . . . . . . . . . . . . . . . . .46
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47~48
Setup and Operation Checklist
Setup and Operation Checklist
(See pages 11~16 for available connection and operational setup options.)
1.Unpack TV and all accessories.
2.Connect all external video and audio equipment. see pages 14 ~ 16.
3Install batteries in remote control. See page 9.
4.Turn TV on. See page 18.
5.Turn video source equipment on.
6.Select viewing source for TV. See page 20.
7.Fine-tune source image and sound to your personal preference or as required by source.
See pages 21 ~ 24.
8.Additional features set up See Contents above.
After reading this manual, keep it handy for future reference.
Owner’s Manual 5
Introduction
Introduction
What is a Plasma Display Panel (PDP)?
A plasma display panel is the latest display technology and the best way to achieve flat panel displays with excellent image quality and large screen sizes that are easily viewable. The PDP can be thought of as a descendant of the neon lamp and it can be also be viewed as a series of fluorescent lamps.
How does it work?
PDP is an array of cells, known as pixels, which are comprised of 3 sub pixels, corresponding to the colors red, green, and blue. Gas in a plasma state is used to react with phosphors in each sub-pixel to produce colored light (red, green, or blue). These phosphors are the same types used in Cathode Ray Tube (CRT) devices such as televisions and common computer monitors.
You get the rich, dynamic colors that you expect. Each sub-pixel is individually controlled by advanced electronics to produce over 16 million different colors. All of this means that you get perfect images that are easily viewable in a display that is less than 5 inches thick.
160° - Wide angle range of vision
Your flat panel plasma screen offers an exceptionally broad viewing angle -- over 160 degrees. This means that the display is clear and visible to viewers anywhere in the room who can see the screen.
Wide Screen
The screen of the Plasma Display is so wide that your viewing experience is as if you are in a theater.
Multimedia
Connect your plasma display to a PC and you can use it for conferencing, games, and Internet browsing. The Picture-in-Picture feature allows you to view your PC and video images simultaneously.
Versatile
The light weight and thin size makes it easy to install your plasma display in a variety of locations where conventional TVs will not fit.
The PDP Manufacturing Process: a few minute colored dots may be present on the PDP screen
The PDP (Plasma Display Panel), which is the display device of this product is composed of 0.9 to 2.2 million cells. A few cell defects will normally occur in the PDP manufacturing process. Several tiny, minute colored dots visible on the screen should be acceptable. This also occurs in other PDP manufacturers' products. The tiny dots appearing does not mean that this PDP is defective. Thus a few cell defects are not sufficient cause for the PDP to be exchanged or returned. Our production technology minimizes these cell defects during the manufacture and operation of this product.
6 Plasma TV
Introduction
Controls
-This is a simplified representation of front panel.
Image shown may be somewhat different from your TV.
Front Panel Controls
ON/OFF |
|
|
|
|
TV/VIDEO MENU |
VOL |
CH |
ON/OFF Button |
MENU Button |
CHANNEL (E, D) Buttons |
|
|
|||
Remote Control Sensor |
TV/VIDEO Button |
VOLUME (F,G) Buttons |
|
Power Standby Indicator |
|
|
|
Illuminates red in standby mode, |
|
|
|
Illuminates green when the TV is |
|
|
|
turned on. |
|
|
|
Owner’s Manual 7
Introduction
Connection Options
Back Connection Panel
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
DVI Input/Audio Input/RGB |
||||||||||||||||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
Input |
||||||||||||||||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
Connect the monitor output con- |
||||||||||||||||||||||||||||||||||||
Remote Control |
nector from a PC to the appro- |
||||||||||||||||||||||||||||||||||||||||||||||
priate input port. |
|||||||||||||||||||||||||||||||||||||||||||||||
Port |
|||||||||||||||||||||||||||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||||||
Connect your wired |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||||
remote control here. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
S-VIDEO Input
A/V 2 A connection available to provide better picture quality than the video input.
S-VIDEO
VIDEO Input
R AUDIO L / MONO VIDEO
DVD/DTV Input (Component 1-2)
Connect a component video/audio device to these
Connects the video signal from a video device.
AUDIO Input
Use to connect to hear stereo sound from an external device.
S-Video Input
Connect S-Video out from an
S-VIDEO device to the S-
VIDEO input.
jacks. |
|
|
|
Monitor Output |
|
||||||||||
|
|
|
|||||||||||||
|
|
|
|
|
|
Connect a second TV or |
|
||||||||
|
|
|
|
|
|
|
|
|
Monitor. |
|
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
DIGITAL AUDIO |
|
|
|
|
|
|
MONITOR |
|
|
|
|
|
|
(OPTICAL) |
|
|
|
|
COMPONENT 2 |
DVD |
|
|
|
||
|
|
|
|
|
|
|
|
OUTPUT |
|
|
|
||
|
|
|
|
|
|
|
|
|
. |
|
|
|
|
|
|
|
|
|
|
|
|
COMPONENT 1 |
DTV |
A/V |
|
|
|
|
|
|
|
|
|
|
|
INPUT |
|
|
Antenna |
||
|
|
|
|
|
|
|
|
INPUT 1 |
(MONO) |
|
|||
|
|
|
|
|
|
|
|
|
|
|
|||
RS-232C INPUT |
REMOTE |
DVI |
COMPONENT1 |
DVI INPUT |
|
RGB INPUT |
R |
L |
|
R AUDIO |
L |
VIDEO |
Analog/DTV |
AUDIO INPUT |
|
|
|
|
S-VIDEO |
||||||||
(CONTROL/SERVICE) |
CONTROL |
INPUT |
INPUT OUTPUT |
(PC/DTV INPUT) |
(PC/DTV INPUT) |
AUDIO INPUT |
VIDEO INPUT |
|
|
|
AC INPUT |
|
|
|
|
|
|
|
|
|
|
Audio (DVI: Digital Visual |
|
|
|
||
|
|
|
|
|
|||
|
Digital |
Audio/Video Input 1 |
|
|
|||
|
Interface/Component1) Input/ |
Antenna 1-2 Inputs |
|||||
|
Connect audio/video out- |
||||||
|
|
|
Digital Audio Output |
Connect cable or antenna signals to the |
|||
|
|
|
put from an external |
||||
Connect digital audio from various types |
TV, either directly or through your cable |
||||||
device to these jacks. |
|||||||
of equipment. Note: In standby mode, |
box. For DTV use Antenna 2 only. |
||||||
|
|||||||
|
|
|
these ports will not work. |
|
|
|
|
|
|
|
RS-232C INPUT |
Power Cord Socket |
(CONTROL/SERVICE) PORT |
This TV operates on an AC power. The voltage is indi- |
Connect to the RS-232C port |
cated on the Specifications page. Never attempt to oper- |
on a PC. |
ate the TV on DC power. |
8 Plasma TV
Installation
Remote Control Key Functions
- When using the remote control, aim it at the remote control sensor on the TV.
LIGHT |
|
|
|
|
|
Illuminates the remote control buttons. |
|
|
|
|
|
TV/VIDEO |
|
|
|
|
|
Selects: DTV, Analog, Video1-2, |
|
|
|
|
|
Component 1-2, RGB-DTV (or RGB-PC), |
|
|
|
|
|
DVI-DTV (or DVI-PC) input sources. |
|
MODE |
POWER |
||
|
LIGHT |
||||
|
|
|
|||
COMP/RGB/DVI |
TV/VIDEO |
COMP/RGB/DVI |
TIM |
ER |
|
Selects: Component 1-2, RGB-DTV (or RGB- |
|
|
|
||
|
|
|
|
|
|
PC), DVI-DTV (or DVI-PC) input sources. |
|
|
|
|
|
NUMBER buttons |
|
|
|
|
|
DASH |
|
|
|
FLASHBK |
|
Used to enter a program number for multiple |
|
|
|
||
|
|
|
|
|
|
program channels such as 2-1,2-2,etc. |
|
|
|
|
|
MUTE |
MUTE |
|
|
SURF |
|
|
VOL |
CH |
|
|
|
Switches the sound on or off. |
|
|
|
|
|
VOLUME UP/DOWN |
|
SAP |
RATIO |
|
|
Increases/decreases the sound level. |
INFO |
|
|
CC |
|
INFO |
|
|
|
|
|
When you watch the TV, displays information |
|
|
|
|
|
on top of the screen. Not available in |
|
|
OK |
|
|
Component 1-2, RGB and DVI mode. |
|
|
|
|
|
SAP
Selects MTS sound: Mono, Stereo, and SAP. Change the audio language in DTV mode.
THUMBSTICK (Up/Down/Left/Right/OK)
Allows you to navigate the on-screen menus and adjust the system settings to your preference.
MENU
Brings up the main menu to the screen.
SOUND
Selects the sound appropriate for the program's character.
MENU |
EXIT |
SOUND VIDEO
PLAY PAUSE STOP RECORD
REW |
FF |
SKIP |
PIP |
PIPCH- |
PIPCH+ |
PIPINPUT |
FREEZE |
ZOOM |
SIGNAL |
SWAP |
ADJUST |
|
|
|
FREEZE
Freezes the currently-viewed picture. Main picture is frozen in PIP/Twin picturre mode.
ADJUST
Adjusts screen position, clock, and phase in PC mode.
ZOOM
Enlarges the main picture size.
SIGNAL
Displays the digital signal strength.
MODE
Selects the remote operating mode: TV, VCR, DVD, CABLE, HDSTB or AUDIO. Select other operating modes, for the remote to operate external devices.
POWER
Turns your TV or any other programmed equipment on or off, depending on mode.
TIMER
Lets you select the amount of time before your TV turns itself off automatically.
FLASHBK
Tunes to the last channel viewed.
SURF
Use to scroll the Surf channel list.
CHANNEL UP/DOWN
Selects available channels found with EZ scan.
RATIO
Changes the aspect ratio.
CC
Select a closed caption:
Off, EZ Mute, and On.
EXIT
Clears all on-screen displays and returns to TV viewing from any menu.
VIDEO
Adjusts the factory preset picture according to the room.
VCR/DVD BUTTONS
Control some video cassette recorders or DVD player ("RECORD" button is not available for DVD player).
PIP
Switches between PIP, POP (Picture-out-of- Picture) and Twin picture modes.
PIPCH-/PIPCH+
Changes to next higher/lower PIP channel.
PIP INPUT
Selects the input source for the sub picture.
SWAP
Exchanges the PIP/main images.
Installing Batteries
•Open the battery compartment cover on the back side and install the batteries matching correct polarity (+ with +, - with -).
•Install two 1.5V AA batteries. Don’t mix old or used batteries with new ones. Replace cover.
Owner’s Manual 9
Installation
Installation
Ensure that the following accessories are included with your plasma display. If an accessory is missing, please contact the dealer where you purchased the product.
1.5V
Owner’s Manual Batteries Power Cord 75Ω Round Cable
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2-TV brackets |
2-TV bracket bolts |
||||
2-Wall brackets |
|
|
|
Remote Control
Attaching the TV assembly to the wall
additional support.
•Install the TV brackets on the TV as shown.
Insert the 2 bolts and tighten securely, in the holes on the bracket. Install the wall brackets on the wall with 4 bolts*,
(not supplied with the product), as shown.
Match the height of the TV brackets and the wall brackets. Check to be sure the brackets are tightened securely.
•Secure the TV assembly to the wall with strong strings or wound wire cables, (not supplied with the product), as shown.
10 Plasma TV
Installation
Installation Instructions
•The TV can be installed in various ways such as on a wall, or on a desktop etc.
•The TV is designed to be mounted horizontally. The speakers shown are optional.
GROUNDING
Ensure that you connect the grounding / earth wire to prevent possible electric shock. If grounding methods are not possible, have a qualified electrician install a separate circuit breaker. Do not try to ground the unit by connecting it to telephone wires, lightening rods, or gas pipes.
Power
Supply
Short-circuit
Breaker
Wall Mount: Horizontal installation |
|
Desktop Pedestal Installation |
|
|
|
|
||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
For proper ventilation, allow a clearance of 4” on each side and 2” from the wall. Detailed installation instructions are available from your dealer, see the optional Wall Mounting Bracket Installation and Setup Guide.
For proper ventilation, allow a clearance of 4” on each side and the top, 2.36” on the bottom, and 2” from the wall. Detailed installation instructions are included in the optional Desktop Stand Installation and Setup Guide available from your dealer.
To Mount on a Wall
Wall mount minimum allowable clearances for adequate ventilation.
|
2 inches |
|
4 inches |
4 inches |
4 inches |
|
4 inches |
To Install on a Desktop
Pedestal mount minimum allowable clearances for adequate ventilation.
|
4 inches |
2 inches |
4 inches |
|
4 inches |
|
|
2.36 inches |
Owner’s Manual 11
Installation |
|
|
|
|
External Equipment Connections |
|
|
|
|
Antenna Connection |
|
|
|
|
Analog and Digital TV signals provided on one antenna |
|
|
|
|
a Cable Box Connections |
|
|
|
|
antenna direction if needed. |
|
|
|
|
Multi-family Dwellings/Apartments |
|
|
|
|
(Connect to wall antenna socket) |
|
|
|
|
Wall Antenna |
|
|
|
|
Socket |
|
|
|
|
Copper Wire |
R |
|
|
|
T |
|
|
|
|
1 |
|
|
Antenna |
|
|
(MONO) |
|
||
|
|
R AUDIO L |
VIDEO |
Analog/DTV |
RF Coaxial Wire (75 ohm) |
|
S-VIDEO |
||
|
|
|
AC INPUT |
|
|
|
|
|
VHF Antenna |
Turn clockwise to tighten. |
|
|
UHF Antenna |
|
Outdoor
Antenna
Single-family Dwellings /Houses (Connect to wall jack for outdoor antenna)
Copper Wire
Be careful not to bend the Copper wire when connecting the antenna.
AC INPUT |
Signal
Amplifier
•In a poor signal area to improve picture quality, purchase and install a signal amplifier.
•If the antenna needs to be split for two TV’s, install a “2- Way Signal Splitter” in the connections.
•If the antenna is not installed properly, contact your dealer for assistance.
Analog and DTV signals provided on two separate antennas |
|
|
|
|
|
Wall Antenna |
Copper Wire |
|
|
|
|
|
|
|
|
|
|
Socket |
RF Coaxial Wire (75 ohm) |
|
|
|
|
|
|
|
|
|
|
|
Analog Antenna |
|
|
|
|
|
Turn clockwise to tighten. |
UT |
|
|
|
Wall Antenna |
|
TOR |
|
|
|
|
T 1 |
(MONO) |
|
Antenna |
|
|
|
V |
|
|
|
Socket |
|
|
R AUDIO L |
VIDEO |
Analog/DTV |
RF Coaxial Wire (75 ohm) |
|
S-VIDEO |
|||
|
|
|
AC INPUT |
||
|
|
|
|
|
Digital Antenna
Copper Wire
NOTE: If you are not sure of the type of signal(s) you are receiving, let EZ Scan complete all the channel signal-type searches. The TV will let you know when the analog, cable, and digital channel scans are complete.
12 Plasma TV
Installation
NOTE: All cables shown are not included with the TV
VCR Setup
(interference), leave an adequate distance between the VCR and (on the Option menu) feature to avoid having a fixed image remain picture from a VCR. If the 4:3 picture format is used; the fixed screen.
1
the screen for a long period of time. on the sides of the screen may
to 3 or 4 and then tune number.
2 |
|
|
|
|
|
|
|
|
|
|
and video cables from the |
|
|
|
|
|
|
|
|
|
|
to the TV input jacks, as |
|
|
|
|
COMPONENT 2 |
DTV |
MONITOR |
|
|
|
|
|
|
|
A/V |
|
|
|
|||
|
|
|
|
|
DVD |
OUTPUT |
|
|
|
|
|
|
|
|
|
|
. |
|
|
|
|
. |
|
|
|
|
COMPONENT 1 |
INPUT |
INPUT 1 |
(MONO) |
|
Antenna |
|
|
|
|
|
|
|
||||
DVI INPUT |
AUDIO INPUT |
RGB INPUT |
R |
L |
|
R AUDIO L |
VIDEO |
S-VIDEO |
Analog/DTV |
|
(PC/DTV INPUT) |
(PC/DTV INPUT) |
AUDIO INPUT |
VIDEO INPUT |
|
|
|
AC INPUT |
|||
|
|
|
|
|
|
|
|
TV to VCR, match the |
|
|
yellow, Audio Left = white, |
|
|
. |
|
|
-VIDEO output from VCR to |
|
|
the picture quality is |
|
|
to connecting a regular |
|
|
. |
1 |
|
into the VCR and press |
2 |
|
(Refer to the VCR owner’s |
|
|
|
|
with using the
the remote control. (If 1, select Video 1
ANT OUT
S-VIDEO |
OUT |
|
|
ANT IN |
|
|
|
OUTPUT |
(R) AUDIO (L) |
VIDEO |
|
SWITCH |
|
|
|
3 |
4 |
IN |
|
VCR
to both Video and the same time.
Cable TV Setup
cable TV service from a local provider and installing a converter, you can watch cable TV programming. TV programming unless a TV tuner device or cable TV converter box is connected to the TV. regarding cable TV service, contact your local cable TV service provider(s).
switch on cable |
|
|
|
|
|
|
|
the same selected |
|
|
|
|
|
|
|
box. |
|
|
|
|
|
|
|
cable box or with the |
|
|
|
|
|
|
|
. |
|
|
COMPONENT 2 |
DVD. |
MONITOR |
|
|
|
|
OUTPUT |
|
|
|||
|
|
|
COMPONENT 1 |
DTV |
A/V |
|
|
|
|
|
INPUT |
INPUT 1 |
(MONO) |
|
|
IO INPUT |
RGB INPUT |
R |
L |
|
R AUDIO L |
VIDEO |
S-VIDEO |
(PC/DTV INPUT) |
AUDIO INPUT |
VIDEO INPUT |
|
|
AC INPUT |
||
|
|
|
|
|
video cables from the |
2 |
|
1 |
to the TV input jacks, |
|
||
|
|
|
to a Cable Box, |
|
|
|
|
(Video = yellow, Audio |
|
|
|
|
Right = red). |
|
|
|
|
with using the |
(R) AUDIO (L) |
OUTPUT |
|
|
|
VIDEO |
|
|
|
remote control. (If |
TV |
SWITCH |
Cable |
|
VCR |
3 |
RF |
||
|
|
4 |
|
|
1, select Video 1 |
|
|
|
|
channel with the remote |
Cable Box |
|
||
|
|
|
|
Owner’s Manual 13
Installation
External A/V Source Setup
the external equipas shown in the
match the = white, and Audio
TV/VIDEO button on INPUT 1, select
. Refer to
|
|
COMPONENT 2 |
DVD |
MONITOR |
|
|
|
|
|
|
OUTPUT |
|
|
|
|
||
|
|
|
. |
|
|
|
|
|
|
|
COMPONENT 1 |
DTV |
A/V |
|
|
|
|
|
|
INPUT |
INPUT 1 |
|
(MONO) |
|
Antenna |
|
NPUT |
R |
L |
|
R AUDIO |
L |
VIDEO |
S-VIDEO |
Analog/DTV |
V INPUT) |
VIDEO INPUT |
INPUT |
AUDIO INPUT |
|
Camcorder
Video Game Set
R AUDIO L |
VIDEO |
Monitor Out Setup
1 |
(MONO) |
Antenna |
R AUDIO L |
VIDEO |
Analog/DTV |
S-VIDEO |
The TV has a special signal output capability which allows you to hook up a second TV or monitor.
Connect the second TV or monitor to the TV’s MONITOR OUTPUT. See the Operating Manual of the second TV or monitor for further INPUT details regarding that device’s input settings.
NOTE
•Component, RGB-PC/RGB-DTV, DVI-PC/DVI-DTV, DTV input sources cannot be used for Monitor out.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
AUDIO (L) |
VIDEO |
|||
|
|
|
|
|
|
|
, PR) to the COMPONENT (Y, |
|
|
|
|
|
|
|
|
|
|
|
the DVD audio outputs |
|
|
|
|
|
|
|
|
|
|
|
as shown in the figure. |
|
|
|
|
|
|
|
|
|
|
|
jack, connect this to the S- |
|
|
|
|
|
|
|
|
|
|
|
DVD audio outputs to the |
|
|
DIGITAL AUDIO |
|
|
|
. |
OUTPUT |
|
|
|
|
|
|
(OPTICAL) |
|
|
COMPONENT 2 |
DVD |
MONITOR |
|
|
|
|
|
|
|
|
|
|
|
|
|
||
in the figure. |
|
|
|
|
|
|
DTV |
A/V |
|
|
|
|
|
|
|
|
COMPONENT 1 |
INPUT |
|
|
Ante |
||
RS-232C INPUT |
REMOTE |
DVI COMPONENT1 |
OUTPUT |
R |
L |
|
R AUDIO L |
VIDEO |
S-VIDEO |
||
|
|
|
|
|
|
|
|
INPUT 1 |
(MONO) |
1 |
|
|
|
|
|
|
|
|
|
|
|
|
D |
component video output, use |
(CONTROL/SERVICE) |
CONTROL |
INPUT INPUT |
|
AUDIO INPUT |
VIDEO INPUT |
|
|
|
|
|
|
|
|
|
|
|
|
|
||||
|
|
|
|
|
|
|
|
|
|
|
. |
or |
|
button on the remote control |
||
|
||
2. (If connected to S- |
|
|
external input source.) |
|
|
operating instructions. |
|
or |
|
DIGITAL AUDIO (R) AUDIO (L) |
B R |
S-VIDEO (R) AUDIO (L) |
|
connect a DVD player to the compo- |
OPTICAL |
|
|
|
|
|
|
|
|
below. |
|
DVD |
|
|
|
|
|
|
Y |
PB |
PR |
|
|
|
|
|
|
|
|
|
Y |
Pb |
Pr |
|
Y |
B-Y |
R-Y |
on DVD player |
Y |
Cb |
Cr |
|
Y |
PB |
PR |
NOTES
•Digital Audio will not work for Component 2 input source.
•Digital Audio operation has priority if Digital Audio and AUDIO L/R are connected at the same time.
14 Plasma TV