LG DR386D User Manual

ENGLISH

DR386D

P/NO : MFL56778743

As an ENERGY

STAR

®

Partner, LG
has determined that this product
or product models meet the
ENERGY

STAR

®

guidelines for

energy efficiency.

ENERGY

STAR

®

is a U.S. registered mark.

DR386D-W.BAUSLLK_ENG 6/16/08 10:38 AM Page 1

2

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE

COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SER­VICING TO QUALIFIED SERVICE PERSONNEL.

This lightning flash with arrowhead symbol within an equilateral triangle
is intended to alert the user to the presence of non insulated dangerous
voltage within the product’s enclosure that may be of sufficient magni­tude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating and maintenance (serv­icing) instructions in the literature accompanying the product.

WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DO NOT
EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

WARNING: Do not install this equipment in a confined space such as a book
case or similar unit.

CAUTION: Do not block any ventilation openings. Install in accordance with the
manufacturer's instructions.
Slots and openings in the cabinet are provided for ventilation and to ensure reli­able operation of the product and to protect it from over heating. The openings
should be never be blocked by placing the product on a bed, sofa, rug or other
similar surface. This product should not be placed in a built-in installation such
as a bookcase or rack unless proper ventilation is provided or the manufactur­er's instructions have been adhered to.

CAUTION:CLASS 3B VISIBLE AND INVISIBLE LASER

RADIATION WEN OPEN AND INTERLOCKS
DEFEATED AVOID EXPOSER TO THE BEAM.

CAUTION: This product employs a Laser System.
To ensure proper use of this product, please read this owner’s manual carefully
and retain it for future reference. Should the unit require maintenance, contact
an authorized service centre.
Use of controls, adjustments or the performance of procedures other than those
specified herein may result in hazardous radiation exposure.
To prevent direct exposure to laser beam, do not try to open the enclosure.
Visible laser radiation when open. DO NOT STARE INTO BEAM.

CAUTION: The apparatus should not be exposed to water (dripping or splash­ing) and no objects filled with liquids, such as vases, should be placed on the
apparatus.

CAUTION concerning the Power Cord
Most appliances recommend they be placed upon a dedicated circuit;

That is, a single outlet circuit which powers only that appliance and has no addi­tional outlets or branch circuits. Check the specification page of this owner's
manual to be certain. Do not overload wall outlets. Overloaded wall outlets,
loose or damaged wall outlets, extension cords, frayed power cords, or dam­aged or cracked wire insulation are dangerous. Any of these conditions could
result in electric shock or fire. Periodically examine the cord of your appliance,
and if its appearance indicates damage or deterioration, unplug it, discontinue
use of the appliance, and have the cord replaced with an exact replacement
part by an LG authorized service centre. Protect the power cord from physical
or mechanical abuse, such as being twisted, kinked, pinched, closed in a door,
or walked upon. Pay particular attention to plugs, wall outlets, and the point
where the cord exits the appliance. To disconnect power from the mains, pull
out the mains cord plug. When installing the product, ensure that the plug is
easily accessible.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

 The appliance is not intended for use by young children or frail persons

without supervision.

 Young Children should be supervised to ensure that they do not play with

appliance.

 If the appliance is supplied from a cord extension set or an electrical portable

outlet device, the cord extension set or electrical portable outlet device must be
positioned so that it is not subject to splashing or ingress of moisture.

DR386D-W.BAUSLLK_ENG 6/16/08 10:38 AM Page 2

3

Copyrights

 Recording equipment should be used only for lawful copying and you are

advised to check carefully what is lawful copying in the area in which you are
making a copy. Copying of copyright material such as films or music is unlaw­ful unless permitted by a legal exception or consented to by the rights owner.

 This product incorporates copyright protection technology that is protected by

method claims of certain U.S. patents and other intellectual property rights
owned by Macrovision Corporation and other rights owners. Use of this copy­right protection technology must be authorized by Macrovision Corporation,
and is intended for home and other limited viewing uses only, unless other­wise authorized by Macrovision corporation. Reverse engineering or disas­sembly is prohibited.

 CONSUMERS SHOULD NOTE THAT NOT ALL HIGH DEFINITION TELEVI-

SION SETS ARE FULLY COMPATIBLE WITH THIS PRODUCT AND MAY
CAUSE ARTIFACTS TO BE DISPLAYED IN THE PICTURE. IN CASE OF
625 PROGRESSIVE SCAN PICTURE PROBLEMS, IT IS RECOMMENDED
THAT THE USER SWITCH THE CONNECTION TO THE ‘STANDARD DEFI­NITION’ OUTPUT. IF THERE ARE QUESTIONS REGARDING OUR TV SET
COMPATIBILITY WITH THIS MODEL 625p DVD RECORDER, PLEASE
CONTACT OUR CUSTOMER SERVICE CENTRE.

Open source software notice

This product includes

 Freetype library : copyright © 2003 The FreeType Project (www.freetype.org).

 Zlib compression library developed by Jean-loup Gailly and Mark Adler.

Copyright (C) 1995-2005 Jean-loup Gailly and Mark Adler

 Doubly Linked List licensed by Artistic license.

You can download this software from http://freshmeat.net/projects/linklist/

Manufactured under license from Dolby Laboratories. Dolby and the
double-D symbol are trademarks of Dolby Laboratories.

DR386D-W.BAUSLLK_ENG 6/16/08 10:38 AM Page 3

4

Contents

Before you start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-6

Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Main Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Hooking up the unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-13

Operating USB Flash Drive . . . . . . . . . . . . . . . . . . . . . . . . . .13

Auto setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14-15

Using the Home Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . .15-16

Adjust the SETUP settings . . . . . . . . . . . . . . . . . . . . . . .16-21

Displaying disc Information . . . . . . . . . . . . . . . . . . . . . . .21-23

Using the digital EPG . . . . . . . . . . . . . . . . . . . . . . . . . . . .24-25

Play a disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25-26

Playing DivX

®

movie files . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Listening to a music . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Viewing a photo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30-31

Editing a title . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32-35

Language Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

Area Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37-38

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39

Before connecting, operating or adjusting this product,
please read this instruction booklet carefully and completely.

DR386D-W.BAUSLLK_ENG 6/16/08 10:38 AM Page 4

5

Before you start

Recordable and Playable discs

This unit can play and record all widely-used DVD types. The table below shows some specific compatibility differences depending on the disc types.

Playable discs

The table below shows the file formats and media types that this unit can playback.

DVD-R DVD-RW DVD-RAM DVD+R DVD+R(DL) DVD+RW

Symbol used in
this manual

Logos

Re-Writable

Formatting Mode
(new discs)

Editing

Play on other
players

Recommended
discs

No Yes Yes No No Yes

Video mode Video mode VR mode Auto Auto Auto

Limited Yes Yes Limited Limited Yes

The player must compatible with corresponding media and the media has to be finalized.

Mitsubishi(8x,16x) Mitsubishi(4x) Mitsubishi(3x) Mitsubishi(8, 16x) Mitsubishi(2.4x, 8x) Mitsubishi(4x)

Verbatim(8x,16x) Verbatim(4x) Maxell(5x) Verbatim(8x,16x) HP(4x)

JVC(4x) Verbatim(4x)

Maxell(4x) Ricoh(4x)

+RW+R+RRAM-RW

Video

-RW

VR

-R

DVD Audio CD Data disc (DivX, JPEG, MP3 or WMA)

Symbol used in
this manual

Logos

Characteristics

WMAMP3

JPEG

DivXACDDVD

Music CDs or CD-R/RWs
in music CD format that
can be purchased

Discs such as movies
that can be
purchased or rented.

Discs that contain DivX, JPEG, MP3 or WMA
files.

DR386D-W.BAUSLLK_ENG 6/16/08 10:38 AM Page 5

6

Notes on discs

 Depending on the conditions of the recording equipment or the CD-R/RW (or

DVD±R/RW) disc itself, some CD-R/RW (or DVD±R/RW) discs cannot be
played on the unit.

 Do not attach any seal or label to either side (the labelled side or the

recorded side) of a disc.

 Do not use irregularly shaped CDs (e.g., heart-shaped or octagonal).

Doing so may result in malfunctions.

 Depending on the recording software & the finalization, some recorded discs

(CD-R/RW or DVD±R/RW) may not be playable.

 DVD-R/RW, DVD+R/RW and CD-R/RW discs recorded using a personal

computer or a DVD or CD Recorder may not play if the disc is damaged or
dirty, or if there is dirt or condensation on the Unit’s lens.

 If you record a disc using a personal computer, even if it is recorded in a

compatible format, there are cases in which it may not play because of the
settings of the application software used to create the disc. (Check with the
software publisher for more detailed information.)

 This unit requires discs and recordings to meet certain technical standards

in order to achieve optimal playback quality. Pre-recorded DVDs are auto­matically set to these standards. There are many different types of record­able disc formats (including CD-R containing MP3 or WMA files) and these
require certain pre-existing conditions (see above) to ensure compatible
playback.

 Customers should note that permission is required in order to download

MP3 / WMA files and music from the Internet. Our company has no right to
grant such permission. Permission should always be sought from the copy­right owner.

Restrictions on copying

Some video material is copy-once protected: Such material cannot be copied to
DVD. You can identify copy-once protected material during playback by display­ing disc information on-screen.

 NTSC format signals from the analog or the DV inputs is not recorded cor-

rectly with this unit.

 Video signals in SECAM format (from the built-in TV tuner or from the ana-

log inputs) are recorded in PAL format.

About the Symbol Display

“ ” may appear on your TV display during operation and indicates that the
function explained in this owner’s manual is not available on that specific media.

Regional Codes

This unit has a regional code printed on the rear of the unit. This unit can play
only DVD discs labelled same as the rear of the unit or “ALL”.

 Most DVD discs have a globe with one or more numbers in it clearly visible

on the cover. This number must match your unit’s regional code or the disc
cannot play.

 If you try to play a DVD with a different regional code from the unit, the mes-

sage “Incorrect region code. Can’t play back” appears on the TV screen.

Remote Control Operation

Point the Remote Control at the remote sensor and press the buttons.

Remote Control Battery Installation

Remove the battery cover on the rear of the Remote Control, and insert R03
(size AAA) battery with 3 and # matched correctly.

Setting up the remote to control your TV

You can operate your TV with the supplied remote control.
If your TV is listed in the table below, set the appropriate manufacturer code.

While holding down TV POWER button, and press the manufacturer code for
your TV with the numerical buttons (see the table below). Release the TV
POWER button to complete setting.

Manufacturer Code Number

LG / GoldStar 1 (Default), 2

Zenith 1, 3, 4

Samsung 6, 7

Sony 8, 9

Hitachi 4

Depending on your TV, some or all buttons may not function on the TV, even
after entering the correct manufacturer code. When you replace the batteries of
the remote, the code number you have set may be reset to the default setting.
Set the appropriate code number again.

DR386D-W.BAUSLLK_ENG 6/16/08 10:38 AM Page 6

7

Remote control

        a        

POWER: Switches the unit ON or OFF.

AV: Changes the input source (Tuner, AV1-2, or

DV IN).

OPEN/CLOSE (Z): Opens and closes the disc tray.

0-9 numerical buttons: Selects numbered options in a

menu.
REC(z): Starts recording. Press repeatedly to set the

recording time.
TV Control Buttons: You can control the sound level,

sound mute, input source, and power switch of your TV.

*

: This button is not available.

        b        

SCAN (m / M): Search backward or forward.
SKIP (. / >): Go to next or previous chapter/track/file.
PAUSE/STEP (X): Pause playback or recording temporarily.
PLAY (N): Starts playback.
STOP (x): Stops playback or recording.

        c        

HOME: Accesses or removes the HOME menu.

MENU/LIST: Accesses menu on a DVD disc. Switches

between Title List-Original and Title List-Playlist menu.

b / B / v / V (left/right/up/down):

Used to navigate on-screen displays.

(ENTER): Acknowledges menu selection or displays the

program list.

PR (+/-): Scans up or down through memorized
channels.

RETURN (O): Removes the on-screen displays.

DISPLAY: Accesses On-Screen Display.

        d        

Colour buttons: Use when an EPG screen is displayed or
when tuned to a teletext program of a digital broadcast. The
function of each button will be described on-screen, and
changes depending on the screen being displayed.

AUDIO ( ): Selects an audio language or audio channel.

TITLE: Displays the disc’s Title menu, if available.
MARKER: Selects multiple files/titles on the list.
CLEAR: Removes a track number on the Program List.
FAV: Displays the favourite program list.

REPEAT: Repeat sequence, chapter, track, title, all.

SUBTITLE: Selects a subtitle language.
TEXT: Switches between teletext mode and normal TV

viewing.
EPG: Displays the EPG menu.

a

b

c

d

DR386D-W.BAUSLLK_ENG 6/16/08 10:38 AM Page 7

8

a

11

/ I (POWER button)

Switches the unit ON or OFF.

b Disc Tray

Insert a disc here.

c OPEN/CLOSE (Z)

Opens or closes the disc tray.

d Remote Sensor

Point the remote control here.

e Display window

Shows the current status of the unit.

REC: The unit is recording.

: Indicates when the unit is in timer recording or a timer recording is pro-

grammed.

: Indicates clock, total playing time, elapsed time, title number,

chapter/track number, channel, etc.

f N / X (PLAY / PAUSE)

Starts playback.
Pause playback or recording temporarily,
press again to exit pause mode.

g x (STOP)

Stops playback or recording.

h z (REC)

Starts recording. Press repeatedly to set the recording time.

i RESOLUTION

Sets the output resolution for HDMI and COMPONENT OUTPUT jacks.

- HDMI: 576i, 576p, 720p, 1080i, 1080p

- COMPONENT: 576i, 576p

j USB Port

Connect an USB Flash Memory.

k DV IN

Connect the DV output of a digital camcorder.

l AV IN 2 (VIDEO IN/AUDIO IN (Left/Right))

Connect the audio/video output of an external source (Audio system, TV/
Monitor, VCR, Camcorder, etc.).

Main Unit

abcdefghi

jk l

DR386D-W.BAUSLLK_ENG 6/16/08 10:38 AM Page 8

9

a Antenna connection

Connect the Terrestrial
TV antenna to the
ANTENNA IN jack on
the unit.
If you want to use an
indoor antenna, use one
with a signal amplifier
rated at 5V, 100mA and
set [Antenna Feed 5V]
to [ON] in the setup
menu.

b Antenna connection to

your TV

Connect one end of the RF
cable to ANTENNA OUT jack
on the unit and other end to
ANTENNA IN jack on your
TV.
Passes the signal from the
ANTENNA IN jack to your
TV/monitor.

c Audio/Video connection

Connect one end of the
video(yellow) cable to the
VIDEO OUTPUT jack on the
unit and other end to the
VIDEO INPUT jack on your
TV.
Connect one end of the
audio cables (red and white)
to the analog AUDIO
OUTPUT jacks on the unit
and other ends to the AUDIO
INPUT jacks on your TV.

d Power cord connection

Connect the mains lead to
the AC IN terminal on the
unit. Then plug the power
cord into the mains.

Antenna

(Digital)

Antenna
(Analog)

and/or

Hooking up the unit

DR386D-W.BAUSLLK_ENG 6/16/08 10:38 AM Page 9

10

Hooking up the unit

General about connection

Picture and sound

Digital TV is a transmission technology that replaces the traditional analogue
technique.

This means that several TV channels, radio channels and other digital services
can be transmitted on the same space as just one channel took up before. As a
consumer you get access to many more channels and services than before at
the same time as they are received with perfect picture and audio quality.

The recorder converts the digital signal into a format that is suitable for your TV
and sound system.

Connecting your recorder is just as simple as connecting for example a video
recorder. You get the best picture quality by using a HDMI cable for connection
to your TV-set. The best audio experience is obtained by connecting an optical
cable to your sound system.

Coverage

Before buying this product it is anticipated that you have made sure that there
are digital transmissions covering your region.

Antenna / Signal source

Depending on the reception your recorder may be connected to a simple indoor
antenna or to an existing outdoor antenna system. If you live in a flat you should
make sure that the digital terrestrial signals are distributed to your wall antenna
outlet. If you have your own antenna system you must make sure that it is
equipped with antennas, filter and/or amplifier that can handle those frequen­cies that the digital channels are transmitted on.

Cable-TV

Please observe that this recorder is not designed for the reception of regular
digital cable-TV signals (QAM-signal). Despite this, operators of smaller cable
networks may have chosen to distribute the digital terrestrial signals (COFDM
signal) in the network. In this case this recorder may well be used.

Check with your landlord if you are insecure about what type of TV-signal that is
provided in the wall antenna outlet.

Component connection

Connect one end of the component (Y PB PR) cables to the COMPONENT
OUTPUT jacks on the unit and other ends to the COMPONENT INPUT jacks on
your TV.
Connect one end of the audio cables (red and white) to the analog AUDIO
OUTPUT jacks on the unit and other ends to the AUDIO INPUT jacks on your
TV.

If your television is a high-definition or “digital ready” television, you may take
advantage of the unit’s progressive scan output for the highest video resolution
possible. If your TV does not accept the Progressive Scan format, the picture
will appear scrambled with the progressive signal.
Set the resolution to 576p using RES. button on the front panel to obtain the
progressive signal.

DR386D-W.BAUSLLK_ENG 6/16/08 10:38 AM Page 10

11

S-Video connection

Connect one end of the S-Video cable to the S-VIDEO OUTPUT jack on the
unit and the other end to the S-VIDEO INPUT jack on your TV.
Connect one end of the audio cables (red and white) to the analog AUDIO
OUTPUT jacks on the unit and the other ends to the AUDIO INPUT jacks on
your TV.

Digital audio connection

Connecting to an amplifier/receiver, Dolby Digital/MPEG/DTS decoder or other
equipment with a digital input.

Connect one end of the digital audio cables (COAXIAL or OPTICAL) to the digi­tal audio output jack (COAXIAL or OPTICAL) on the unit and other end to the
digital audio input jack (COAXIAL or OPTICAL) on your amplifier.

This recorder does not perform internal (2 channel) decoding of a DTS sound
track . To enjoy DTS multi channel surround, you must connect this recorder to
a DTS compatible receiver via one of this recorder’s digital audio output.

DR386D-W.BAUSLLK_ENG 6/16/08 10:38 AM Page 11

12

HDMI connection

Connect one end of the HDMI cable to the HDMI OUTPUT jack on the unit and
other end to the HDMI INPUT jack on your TV.

When you use the HDMI connection, you can change the resolution (576i,
576p, 720p,1080i or 1080p) for the HDMI output by pressing RES. button

repeatedly

.

About HDMI

HDMI (High Definition Multimedia Interface) supports both video and audio on a
single digital connection for use with DVD Players, Set-Top Boxes, and other AV
devices.
HDMI was developed to provide the technologies of HDCP (High-bandwidth
Digital Contents Protection). HDCP is used to protect digital content transmitted
and received.

HDMI has the capability to support standard, enhanced, or high-definition video
plus standard to multi-channel surround-sound audio, HDMI features include
uncompressed digital video, a bandwidth of up to 5 gigabytes per second, one
connector (instead of several cables and connectors), and communication
between the AV source and AV devices such as DTVs.

HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks
or registered trademarks of HDMI licensing LLC.

Note on HDMI connection

 If your TV is NOT capable of handling 96 kHz sampling frequency, set

the [Sampling Freq.] option to [48 kHz] on the setup menu (See page

18). When this choice is made, this unit will automatically convert any 96
kHz signals to 48 kHz so your system can decode them.

 If your TV is not equipped with Dolby Digital and MPEG decoder, set the

[Dolby Digital] and [MPEG] options to [PCM] on the setup menu (See
page 18).

 If your TV is not equipped with DTS decoder, set the [DTS] options to

[OFF] on the setup menu (See page 18). To enjoy DTS multi channel
surround, you must connect this unit to a DTS compatible receiver via
one of this unit’s digital audio outputs.

 If there is noise or lines on the screen, please check the HDMI cable.

 Changing the resolution when the unit is connected with HDMI connector

may result in malfunctions. To solve the problem, turn off the unit and
then turn it on again.

 When you connect a HDMI or DVI compatible device make sure of the

following:

- Try switching off the HDMI/DVI device and this unit. Next, switch on
the HDMI/DVI device and leave it for around 30 seconds, then switch
on this unit.

- The connected device’s video input is set correctly for this unit.

- The connected device is compatible with 720(1440)x576i, 720x576p,
1280x720p, 1920x1080i or 1920x1080p video input.

 Not all HDCP-compatible DVI devices will work with this unit.

- The picture will not be displayed properly with non-HDCP device.

What is SIMPLINK?

Some functions of this unit are controlled by TV’s remote control when this
unit and LG TV with SIMPLINK are connected through HDMI connection.

• Controllable functions by LG TV’s remote control; Play, Pause, Scan, Skip,
Stop, Power Off, etc.

• Refer to the TV owner’s manual for the details of SIMPLINK function.

• LG TV with SIMPLINK function has the logo as shown above.

TV

Recorder

DR386D-W.BAUSLLK_ENG 6/16/08 10:38 AM Page 12