<![endif]>~ ESPANOL ENGLISH
OWNER’S MANUAL
DRYER
Please read this manual carefully before operating your dryer and retain it for future reference.
DLEX5101W DLGX5102W
DLEX5101V DLGX5102V
P/No. MFL62512847 |
www.lg.com |
IMPORTANT SAFETY INSTRUCTIONS |
|
What to Do if You Smell Gas................................... |
3 |
Basic Safety Precautions........................................ |
4 |
California Safe Drinking Water And Toxic |
|
Enforcement Act.................................................... |
4 |
Grounding Instructions........................................... |
5 |
Safety Instructions for Installation........................... |
5 |
Safety Instructions for Steam Functions................. |
6 |
Safety Instructions for Connecting Electricity ........ |
7 |
PARTS AND FEATURES |
|
Special Features..................................................... |
8 |
Key Parts and Components.................................... |
9 |
INSTALLATION INSTRUCTIONS |
|
Installation Location Requirements....................... |
10 |
Clearances............................................................ |
10 |
Leveling the Dryer................................................. |
11 |
Reversing the Door............................................... |
12 |
Changing the Dryer Vent Location........................ |
13 |
Venting the Dryer................................................... |
14 |
Connecting Gas Dryers......................................... |
16 |
Connecting Electric Dryers................................... |
18 |
Special Requirements for Manufactured |
|
or Mobile Homes................................................... |
23 |
Final Installation Check ........................................ |
23 |
Duct Condition Test.............................................. |
24 |
HOW TO USE |
|
Control Panel Features.……………….…..………..25 |
|
Operating The Dryer.……………………………..…26 |
|
Cycle Guide…………………………………………..27 |
|
Sorting Loads………………………………………..28 |
|
Loading the Dryer.…………....…………………..…28 |
|
Check The Lint Filter Before Every Load.………...28 |
|
TheDisplay…………………………………………...29 |
|
Cycle Setting Buttons……………………………….30 |
|
Cycle Option Buttons...……………………………..31 |
|
Custom Program…………………………………….31 |
|
Steam Functions…………………………………….32 |
|
Steam Cycle Guide ………………………………....34 |
|
user maintenance instructions |
|
Regular Cleaning................................................... |
35 |
TROUBLESHOOTING |
|
Before Calling for Service..................................... |
36 |
SPECIFICATIONS |
|
Key Dimensions And Specifications..................... |
39 |
THANK YOU!
Congratulations on your purchase
and welcome to the LG family. Your
new LG Dryer combines the most
advanced drying sensor technology
with simple operation and high
efficiency.
Follow the operating and care instructions in this manual and your
dryer will provide many years of
reliable service.
2
READ ALL INSTRUCTIONS BEFORE USE
wWARNING For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, personal injury, or loss of life.
Your Safety and the safety of others is very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word DANGER or WARNING. These words mean:
wDANGER: You can be killed or seriously injured if you don’t immediately follow instructions.
wWARNING: You can be killed or seriously injured if you don’t follow instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.
• Do not install a clothes dryer with flexible plastic venting materials. If flexible metal (foil type) duct is installed, it must be of a specific type identified by the appliance manufacturer as suitable for use with clothes dryers. Flexible venting materials are known to collapse, be easily crushed, and trap lint. These conditions will obstruct clothes dryer airflow and increase the risk of fire.
• Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this appliance or any other appliances.
•Installation and service must be performed by a qualified installer, service agency, or the gas supplier.
•Install the clothes dryer according to the manufacturer’s instructions and local codes.
•Save these instructions.
WHAT TO DO IF YOU SMELL GAS:
1.Do not try to light a match or cigarette, or turn on any gas or electrical appliance.
2.Do not touch any electrical switches. Do not use any phone in your building.
3.Clear the room, building, or area of all occupants.
4.Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions carefully.
5.If you cannot reach your gas supplier, call the fire department.
<![endif]>ENGLISH
3
READ ALL INSTRUCTIONS BEFORE USE
wWARNING For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, personal injury, or loss of life.
BASIC SAFETY PRECAUTIONS
wWARNING: To reduce the risk of fire, electric shock, or personal injury when using this appliance, follow basic precautions, including the following:
•Read all instructions before using the dryer.
•Before use, the dryer must be properly installed as described in this manual.
•Do not place items exposed to cooking oils in your dryer. Items contaminated with cooking oils may contribute to a chemical reaction that could cause a load to catch fire.
•Do not dry articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, dry-cleaning solvents, or other flammable or explosive substances as they give off vapors that could ignite or explode.
•Do not reach into the dryer if the drum or any other part is moving.
•Do not repair or replace any part of the dryer or attempt any servicing unless specifically recommended in this Use and Care Guide or in published user-repair instructions that you understand and have the skills to carry out.
•Do not tamper with controls.
•Before the dryer is removed from service or discarded, remove the door to the drying compartment.
•Do not allow children to play on or in the dryer.
Close supervision of children is necessary when the dryer is used near children.
•Do not use fabric softeners or products to eliminate static unless recommended by the manufacturer of the fabric softener or product.
•Do not use heat to dry articles containing foam rubber or similarly textured rubber-like materials.
•Keep area around the exhaust opening and adjacent surrounding areas free from the accumulation of lint, dust, and dirt.
•The interior of the dryer and exhaust vent should be cleaned periodically by qualified service personnel.
•Do not install or store the dryer where it will be exposed to the weather.
•Always check the inside of the dryer for foreign objects.
•Clean lint screen before or after each load.
California Safe Drinking Water and Toxic Enforcement Act
This act requires the Governor of California to publish a list of substances known to the state to cause cancer, birth defects, or other reproductive harm and requires businesses to warn customers of potential exposure to such substances.
Gas appliances can cause minor exposure to four of these substances, namely benzene, carbon monoxide, formaldehyde, and soot, caused primarily by the incomplete combustion of natural gas or LP fuels.
Properly adjusted dryers will minimize incomplete combustion. Exposure to these substances can be minimized further by properly venting the dryer to the outdoors.
4
READ ALL INSTRUCTIONS BEFORE USE
wWARNING For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, personal injury, or loss of life.
GROUNDING INSTRUCTIONS
This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This appliance must be equipped with a cord having an equipment-grounding conductor and
a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.
Do not modify the plug provided with the appliance. If it will not fit the outlet, have a proper outlet installed by a qualified electrician.
This appliance must be connected to a grounded metal, permanent wiring system or an equipmentgrounding conductor must be run with the circuit conductors and connected to the equipmentgrounding terminal or lead on the appliance.
Electrical shock can result if the dryer is not properly grounded.
wWARNING — Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service person if you are in doubt as to whether the appliance is properly grounded
SAFETY INSTRUCTIONS FOR INSTALLATION
wWARNING: To reduce the risk of fire, electric shock, or personal injury when using this appliance, follow basic precautions, including the following:
•Properly ground dryer to conform with all governing codes and ordinances. Follow details in the installation instructions. Electrical shock can result if the dryer is not properly grounded.
•Before use, the dryer must be properly installed as described in this manual.
Electrical shock can result if the dryer is not properly grounded.
•Install and store the dryer where it will not be exposed to temperatures below freezing or exposed to the weather.
•All repairs and servicing must be performed by an authorized servicer unless specifically recommended in this Owner’s Guide. Use only authorized factory parts. Failure to follow this warning can cause serious injury, fire, electrical shock, or death.
•To reduce the risk of electric shock, do not install the dryer in humid spaces. Failure to follow this warning can cause serious injury, fire, electrical shock, or death.
•Connect to a properly rated, protected, and sized power circuit to avoid electrical overload. Improper power circuit can melt, creating electrical shock and/or fire hazard.
•Remove all packing items and dispose of all shipping materials properly. Failure to do so can result in death, explosion, fire, or burns.
•Place dryer at least 18 inches above the floor for a garage installation. Failure to do so can result in death, explosion, fire, or burns.
•Keep all packaging from children. Packaging material can be dangerous for children. There is a risk of suffocation.
•Do not install nearby heat item. Such a stove, oven or heater. Failure to do so can cause malfunction, smoke, or fire.
•Do not place candle and cigarettes on top of the product. Failure to do so can cause them to melt, smoke, or catch fire.
•Remove all protective vinyl film from the product. Failure to do so can cause them to melt, smoke, or catch fire.
<![endif]>ENGLISH
5
READ ALL INSTRUCTIONS BEFORE USE
wWARNING For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, personal injury, or loss of life.
SAFETY INSTRUCTIONS FOR INSTALLATION
Exhaust/Ducting:
•Gas dryers MUST be exhausted to the outside. Failure to follow these instructions can result in fire or death.
•The dryer exhaust system must be exhausted to the outside of the dwelling. If the dryer is not exhausted outdoors, some fine lint and large amounts of moisture will be expelled into the laundry area. An accumulation of
lint in any area of the home can create a health and fire hazard.
•Use only rigid metal or flexible metal 4-inch diameter ductwork inside the dryer cabinet or for exhausting to the outside. Use of plastic or other combustible ductwork can cause a fire. Punctured ductwork can cause a fire if it collapses or becomes otherwise restricted in use or during installation.
•Ductwork is not provided with the dryer, and you should obtain the necessary ductwork locally. The end cap should have hinged dampers to prevent backdraft when the dryer is not in use. Failure to follow these instructions can result in fire or death.
•The exhaust duct must be 4 inches
(10.2 cm) in diameter with no obstructions. The exhaust duct should be kept as short as possible. Make sure to clean any old ducts before installing your new dryer. Failure to follow these instructions can result in fire or death.
•Rigid or semi - rigid metal ducting is recommended for use between the dryer and the wall. In special installations
when it is impossible to make a connection with the above recommendations, a ULlisted flexible metal transition duct may be used between the dryer and wall connection only. The use of this ducting will affect drying time. Failure to follow these instructions can result in fire or death.
•DO NOT use sheet metal screws or other fasteners which extend into the duct that could catch lint and reduce the efficiency of the exhaust system. Secure all joints with duct tape. For complete details, follow the Installation Instructions. Failure to follow these instructions can result in fire or death.
SAFETY INSTRUCTIONS FOR STEAM FUNCTIONS
wWARNING: To reduce the risk of fire, electric shock, or personal injury when using this appliance, follow basic precautions, including the following:
•Do not open the dryer door during steam cycles. Failure to follow these instructions can result in a burn hazard.
•Do not dry articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, dry-cleaning solvents, or other flammable or explosive substances as they give off vapors that could ignite or explode.
Failure to follow these instructions can result in fire or death.
•Do not fill the steam feeder with gasoline, dry-cleaning solvents, or other flammable or explosive substances. Failure to follow these instructions can result in fire or death.
•Do not touch the steam nozzle in the drum during or after the steam cycle. Failure to follow these instructions can result in a burn hazard.
•Do not fill the steam feeder with hot water (over 86°F/30°C). Failure to follow these instructions can result in a burn hazard.
6
READ ALL INSTRUCTIONS BEFORE USE
wWARNING For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, personal injury, or loss of life.
SAFETY INSTRUCTIONS FOR CONNECTING ELECTRICITY
wWARNING: To reduce the risk of fire, electric shock, or personal injury when using this appliance, follow basic precautions, including the following:
•Do not, under any circumstances, cut or remove the ground prong from the power cord. To prevent personal injury or damage to the dryer, the electrical power cord must be plugged into a properly grounded outlet.
•For personal safety, this dryer must be properly grounded. Failure to do so can result in electrical shock or injury.
•Refer to the installation instructions in this manual for specific electrical requirements for your model. Failure to follow these instructions can create an electrical shock hazard and/or a fire hazard.
•This dryer must be plugged into a properly grounded outlet. Electrical shock can result if the dryer is not properly grounded. Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly grounded. Failure to follow these instructions can create an electrical shock hazard and/or a fire hazard.
•The dryer should always be plugged into its own individual electrical outlet which has a voltage rating that matches the rating plate. This provides the best performance and also prevents overloading house wiring circuits which could cause a fire hazard from overheated wires.
•Never unplug your dryer by pulling on the power cord. Always grip plug firmly and pull straight out from the outlet. The power cord can be damaged, resulting in a risk of fire and electrical shock.
•Repair or replace immediately all power cords that have become frayed or otherwise damaged. Do not use a cord that shows cracks or abrasion damage along its length or at either end. The power cord can melt, creating electrical shock and/or fire hazard.
•When installing or moving the dryer, be careful not to pinch, crush, or damage the power cord. This will prevent injury and prevent damage to the dryer from fire and electrical shock.
<![endif]>ENGLISH
SAVE THESE INSTRUCTIONS
7
SPECIAL FEATURES
A Easy-to-USE Control Panel |
E |
Rotate the cycle selector knob to select the |
|
desired dry cycle. Add cycle options or adjust |
|
settings at the touch of a button. |
|
|
D |
B EASY-ACCESS REVERSIBLE DOOR |
|
Wide-opening door provides easy access for |
|
loading and unloading. Door swing can be |
|
reversed to adjust for installation location. |
|
C Ultra-Capacity Stainless Steel Drum with DRUM Light
The ultra-large stainless steel drum offers superior durability. The drum is equipped with a light that illuminates when the dryer door is open and turns off when the door is closed.
DSTEAM FUNCTIONS
LG’s steam technology allows you to inject fabrics with a swirling jet of hot steam to refresh clothes, reduce static, and make ironing easier. Simply select the STEAMFRESH™ cycle, or you can add a steam option to selected cycles.
EFLOW SENSE™ DUCT BLOCKAGE SENSING SYSTEM INDICATOR
The FLOW SENSE™ duct blockage sensing system detects and alerts you to blockages in the ductwork that reduce exhaust flow from the dryer. Clean exhaust systems increase efficiency and reduce drying times.
A
B
C
8
KEY PARTS AND COMPONENTS
In addition to the special features and components outlined in the Special Features section, there are several other important components that are referenced in this manual.
A FRONT-MOUNT LINT FILTER
Front-mounted lint filter allows for easy access and cleaning after every load.
B Leveling Feet
Four leveling feet (two in the front, and two in the back) adjust to improve dryer stability on uneven floors.
C Drying Rack |
|
A |
|
|
|
Use the drying rack with the RACK DRY cycle to safely dry |
|
|
such items as sweaters, delicates and gym shoes without |
|
|
tumbling or overheating. |
|
|
|
B |
|
|
Terminal Block |
Power Cord Location |
|
Access Panel |
|
|
(Gas Models) |
|
|
(Electric Models) |
|
|
|
C
Included Accessories
Drying Rack
Gas
Connection |
Exhaust Duct |
Location |
Outlet |
(Gas Models) |
|
|
Rear of Dryer |
<![endif]>ENGLISH
9
IMPORTANT: Follow the operating and care instructions in this manual and your dryer will provide many years of reliable service.
It is important that you review this entire manual before installing and using your dryer. Detailed instructions concerning electrical connections, gas connections, and exhaust requirements are provided on the following pages.
INSTALLATION LOCATION REQUIREMENTS
A location that allows for proper exhaust installation. A gas dryer must be exhausted to the outdoors. See
Venting Requirements.
A grounded electrical outlet located within 2 ft. (61 cm) of either side of the dryer. See Electrical Requirements.
A sturdy floor to support the total dryer weight of 200 lbs (90.7 kg). The combined weight of a companion appliance should also be considered.
A level floor with a maximum slope of 1 inch (2.5 cm) under entire dryer. If slope is greater than 1 inch (2.5 cm), install Extended Dryer Feet Kit. Clothes may not tumble properly, and automatic sensor cycles may not operate correctly if dryer is not level.
For a garage installation, you will need to place the dryer at least 18 inches (46 cm) above the floor. If using a pedestal, you will need 18 inches (46 cm) to the bottom of the dryer.
Do not operate your dryer at temperatures below 45º F (7º C). At lower temperatures, the dryer might not shut off at the end of an automatic cycle. This can result in longer drying times.
The dryer must not be installed or stored in an area where it will be exposed to water and/or weather.
Check code requirements. Some codes limit, or do not permit, installation of the dryer in garages, closets, mobile homes or sleeping quarters. Contact your local building inspector.
NOTE: No other fuel-burning appliance can be installed in the same closet as a dryer.
CLEARANCES |
|
|
|
|
|
|
|
|
|
3" |
|
14" max.* |
|
|
|
(7.6 cm) |
|
|
|
|
|
|
|
(35.6 cm) |
|
|
|
|
|
21 1⁄4" |
|
|
|
|
|
(54 cm) |
|
|
|
|
|
|
|
|
|
48 in.2" |
|
|
|
|
|
(310 cm2) |
|
|
45 7⁄16" |
|
|
|
|
|
(115.3 cm) |
|
|
|
|
|
|
|
|
24 in.2" |
|
|
|
|
|
(155 cm2) |
|
28 15⁄16" |
5"** |
1" |
27" |
1" |
|
(73.4 cm) |
(12.7 cm) |
(2.54 cm) |
(68.6 cm) |
(2.54 cm) |
Closet Door Vent |
|
|
|
3" |
||
50 1⁄4" |
|
|
|
||
|
|
|
(7.6 cm) |
Requirements |
|
(127.5 cm) |
|
|
|
|
|
Installation spacing for recessed area or closet installation
The following spacing dimensions are recommended for this dryer. This dryer has been tested for spacing of 0 inches (0 cm) clearance on the sides and rear.
Recommended spacing should be considered for the following reasons:
Additional spacing should be considered for ease of installation and servicing.
Additional clearances might be required for wall, door and floor moldings.
Additional spacing should be considered on all sides of the dryer to reduce noise transfer.
For closet installation, with a door, minimum ventilation openings in the top and bottom of the door are required. Louvered doors with equivalent ventilation openings are acceptable.
Companion appliance spacing should also be considered.
Suggestion: There should be at least a little space around the dryer (or any other appliance) to eliminate the transfer of vibration from one to the other. Too much vibration could cause them to make noise or touch each other, causing paint damage and making even more noise.
10
CLEARANCES (cont.)
IMPORTANT:If you are installing your dryer using an optional pedestal base or stacking kit, please refer to Optional Accessories in this manual or to the instructions for your pedestal or
stacking kit before proceeding with the installation.
Recommended installation spacing for cabinet installation
For cabinet installation, with a door, minimum ventilation openings in the top of the cabinet are required.
*Required spacing
**For side or bottom venting, 2inches (5.1 cm) spacing is allowed.
<![endif]>ENGLISH
LEVELING THE DRYER
wWARNING To reduce the risk of personal injury, adhere to all industry recommended safety procedures including the use of long sleeved gloves and safety glasses. Failure to follow all of the safety warnings in this
manual could result in property damage, personal injury or death.
To ensure that the dryer provides optimal drying performance, it must be level. To minimize vibration, noise, and unwanted movement, the floor must be a level, solid surface.
NOTE: Adjust the leveling feet only as far as necessary to level the dryer. Extending the leveling feet more than necessary can cause the dryer to vibrate.
•All four leveling feet must rest solidly on the floor. Gently push on the top corners of the dryer to make sure that the dryer does not rock from corner to corner.
Level
Leveling Feet
1Position the dryer in the final location. Place a level across the top of the dryer.
2Use an adjustable wrench to turn the leveling feet. Turn clockwise to raise the dryer or counterclockwise to lower it. Raise or lower the leveling feet until dryer is level from
side to side and front to back.
Make sure that all 4 leveling feet are in firm
contact with the floor. |
11 |
|
REVERSING THE DOOR
Hole cap
1Open the door and remove the two plastic hole caps on the catch side by gently prying up with a flat blade screwdriver. Save these for step 6.
CAUTION
Support the weight of the door when removing the screws in the next step. Failure to properly support the weight of the door could result
in property damage, damage to the dryer, or personal injury.
Hinge Screw
Hinge assembly
Cover cap
4Remove the 4 screws securing the hinges to the door frame. Remove the two plastic cover
caps. Reinstall the hinges and cover caps on the opposite sides from which they were removed.
5With the hinges and cover caps in the new locations, remount the inner door frame onto the outer door frame with the screws removed in step 3 above.
2While supporting the door, remove the 4 screws, two from each hinge. Set the door aside face down on a protected surface to prevent damage to the door or the work surface.
inner door frame
latch hook
3With the door on a protected surface, remove the 12 screws on each side of the door and lift off the inner door frame using a flat blade screwdriver. Remove the latch hook and blank and move them to the opposite side.
6Reinstall the door with the screws from step 1,2.
Swing Door
7Test the swing of the door to make sure the hinges and latch are properly aligned and that the door closes and latches correctly.
12
CHANGING THE DRYER VENT LOCATION
wWARNING |
Retaining |
• Use a heavy metal vent. |
Screw |
|
|
• Do not use plastic or thin foil duct. |
|
• Clean old ducts before installing this dryer. |
|
•Protect your hands and arms from sharp edges when working inside the cabinet.
•To reduce the risk of personal injury, adhere to all industry recommended safety procedures including the use of long
sleeved gloves and safety glasses. |
Rear |
|
• Failure to follow all of the safety warnings in this manual |
||
Exhaust Duct |
||
could result in property damage, personal injury or death. |
||
|
||
Your new dryer is shipped to vent to the rear. |
|
|
It can also be configured to vent to the bottom or side |
1 Remove the rear exhaust duct retaining |
|
(right-side venting is not available on gas models). |
||
An adapter kit, part number 383EEL9001B, |
screw. Pull out the exhaust duct. |
|
|
||
may be purchased from your LG retailer. This kit |
|
|
contains the necessary duct components to change |
|
|
the dryer vent location. |
|
|
OPTION 1: Side Venting |
OPTION 2: Bottom Venting |
|
Adapter |
Adapter |
|
Duct |
Duct |
|
Bracket |
|
|
Knockout |
Bracket |
|
|
||
2 Press the tabs on the knockout and carefully |
2 Press the adapter duct onto the blower |
|
remove the knockout for the desired vent opening |
housing and secure to the base of the dryer |
|
(right-side venting is not available on gas models). |
as shown. |
Press the adapter duct onto the blower housing and secure to the base of the dryer as shown.
Cover |
Cover |
|
Plate |
||
Elbow |
Plate |
|
Elbow |
||
11/2" |
||
|
||
(3.8 cm) |
|
|
3 Preassemble a 4-inch (10 cm) elbow to the next |
3 Insert the 4-inch (10 cm) elbow through the |
|
4-inch (10 cm) duct section, and secure all joints |
rear opening and press it onto the adapter |
|
with duct tape. Be sure that the male end of the |
duct. Be sure that the male end of the elbow |
|
elbow faces AWAY from the dryer. |
faces down through hole in the bottom of the |
|
Insert the elbow/duct assembly through the side |
dryer. Secure in place with duct tape. |
|
opening and press it onto the adapter duct. |
Attach the cover plate to the back of the |
|
Secure in place with duct tape. |
dryer with included screw. |
|
Be sure that the male end of the duct protrudes |
|
|
1½ inches (3.8 cm) to connect the remaining |
|
|
ductwork. |
|
|
Attach cover plate to the back of the dryer with |
|
|
included screw. |
13 |
|
|
<![endif]>ENGLISH
VENTING THE DRYER
wWARNING: To reduce the risk of fire, electric shock, or personal injury when using this appliance, follow basic precautions, including the following:
•Do not crush or collapse ductwork. Failure to follow these instructions can result in fire or death.
•Do not allow ductwork to rest on or contact sharp objects. Failure to follow these instructions can result in fire or death.
•If connecting to existing ductwork, make sure it is suitable and clean before installing the dryer. Failure to follow these instructions can result in fire or death.
•Venting must conform to local building codes. Failure to follow these instructions can result in fire or death.
•Gas dryers MUST exhaust to the outdoors.
Failure to follow these instructions can result in fire or death.
•Use only 4-inch (10.2 cm) rigid or flexible metal ductwork inside the dryer cabinet and for venting outside. Failure to follow these instructions can result in fire or death.
•To reduce the risk of fire, combustion, or accumulation of combustible gases, DO NOT exhaust dryer air into an enclosed and unventilated area, such as an attic, wall, ceiling, crawl space, chimney, gas vent, or concealed space of a building. Failure to follow these instructions can result in fire
or death.
•To reduce the risk of fire, DO NOT exhaust the dryer with plastic or thin foil ducting.
Failure to follow these instructions can result in fire or death.
•The exhaust duct must be 4 inches (10.2 cm) in diameter with no obstructions. The exhaust duct should be kept as short as possible. Make sure to clean any old ducts before installing your new dryer. Failure to follow these instructions can result in fire or death.
•Rigid or semirigid metal ducting is recommended for use between the dryer and the wall. In special installations when it is impossible to make a connection with the above recommendations, a UL-listed flexible metal transition duct may be used
between the dryer and wall connection only. The use of this ducting will affect drying
time. Failure to follow these instructions can result in fire or death.
• DO NOT use sheet metal screws or other fasteners which extend into the duct that could catch lint and reduce the efficiency of the exhaust system. Secure all joints with duct tape. Failure to follow these instructions can result in fire or death.
•To maximize operating results, please observe the duct length limitations noted in the chart on page 15. Failure to follow these
instructions can result in fire or death.
•Ductwork is not provided with the dryer. You should obtain the necessary ductwork locally. The end cap should have hinged dampers to prevent backdraft when the dryer is not in use. Failure to follow these
instructions can result in fire or death.
•The Total length of flexible metal duct shall not exceed 8 ft. (2.4m)
•In Canada, that only those foil-type flexible ducts, if any, specifically identified for use with the appliance by the manufacturer
shall be used. In the United States, that only those foil-type flexible ducts, if any, specifically identified for use with the appliance by the manufacturer and that comply with the outline for Clothes Dryer Transition Duct, Subject 2158A, shall be used.
14
VENTING THE DRYER (cont.) |
|
<![if ! IE]> <![endif]>ENGLISH |
||
Ductwork |
|
|
|
|
Wall Cap Type |
Number of 90° Elbows |
Maximum Length of 4-inch Diameter |
||
Rigid Metal Duct |
|
|||
|
|
|
|
|
Recommended |
0 |
65 ft. (19.8 m) |
|
|
1 |
55 ft. (16.8 m) |
|
||
|
|
|
||
|
|
2 |
47 ft. (13.7 m) |
|
4" |
4" |
3 |
36 ft. (11.0 m) |
|
(10.2 cm) |
(10.2 cm) |
4 |
28 ft. (8.5 m) |
|
|
|
|
||
Use Only for Short |
0 |
55 ft. (16.8 m) |
|
|
Run Installations |
1 |
47 ft. (13.7 m) |
|
|
|
|
2 |
41 ft. (12.5 m) |
|
21/2" |
|
3 |
30 ft. (9.1 m) |
|
|
|
|
|
|
(6.35 cm) |
|
4 |
22 ft. (6.7 m) |
|
|
|
|
NOTE: Deduct 6 ft. (1.8 m) for each additional elbow. It is not recommended to use more than four 90° elbows.
Routing and Connecting Ductwork
Follow the guidelines below to maximize drying performance and reduce lint buildup and condensation in the ductwork.
NOTE: Ductwork and fittings are NOT included and must be purchased separately.
•Use 4-inch (10.2 cm) diameter rigid or semirigid metal ductwork.
•The exhaust duct run should be as short as possible.
•Use as few elbow joints as possible.
•The male end of each section of exhaust duct must point away from the dryer.
•Use duct tape on all duct joints.
•Insulate ductwork that runs through unheated areas in order to reduce condensation and lint buildup on duct surfaces.
IMPORTANT: Failure to exhaust the dryer correctly will void the dryer’s warranty.
Correct Venting |
Incorrect Venting |
15
ConnecTING GAS DRYERS
wWARNING: To reduce the risk of fire, electric shock, or personal injury when using this appliance, follow basic precautions, including the following:
• Gas supply requirements:
As shipped from the factory, this dryer is configured for use with natural gas. It can be converted for use with LP (Liquefied Propane) gas. Gas pressure must not exceed 13 inches of water column.
•A qualified service or gas company technician must connect the dryer to the gas service.
Failure to do so can result in fire, explosion, or death.
•Isolate the dryer from the gas supply system by closing its individual manual shutoff valve during any pressure testing of the gas supply.
Failure to do so can result in fire, explosion, or death.
•Supply line requirements:
Your laundry room must have a rigid gas supply line to your dryer. In the United States, an individual manual shutoff valve MUST be installed within at least 6 ft. (1.8 m) of the dryer, in accordance with the National Fuel Gas Code
ANSI Z223.1 or Canadian gas installation code CSA B149.1. A 1⁄8 - inch NPT pipe plug must be installed. Failure to do so can result in fire, explosion, or death
•If using a rigid pipe, the rigid pipe should be
½- inch IPS. If acceptable under local codes
and ordinances and when acceptable to your gas supplier, 3⁄8 - inch approved tubing may be used where lengths are less than 20 ft.
(6.1 m). Larger tubing should be used for lengths in excess of 20 ft. (6.1 m). Failure to do
so can result in fire, explosion, or death.
•Connect the dryer to the type of gas shown on the nameplate. Failure to do so can result in fire, explosion, or death.
•To prevent contamination of the gas valve, purge the gas supply of air and sediment before connecting the gas supply to the dryer. Before tightening the connection between the gas supply and the dryer, purge remaining air until the odor of gas is detected. Failure to do so can result in fire, explosion, or death.
•DO NOT use an open flame to inspect for gas leaks. Use a noncorrosive leak-detection fluid.
Failure to do so can result in fire, explosion, or death.
•Use only a new AGAor CSA-certified gas supply line with flexible stainless steel connectors. Failure to do so can result in fire,
explosion, or death.
•Securely tighten all gas connections. Failure to do so can result in fire, explosion, or death.
•Use Teflon® tape or a pipe-joint compound that is insoluble in Liquefied Petroleum (LP) gas on all pipe threads. Failure to do so can result in fire, explosion, or death.
•DO NOT attempt any disassembly of the dryer; any disassembly requires the attention and tools of an authorized and qualified service person or company. Failure to do so can result in fire, explosion, or death.
Electrical Requirements for Gas Models Only
wWARNING: To reduce the risk of fire, electric shock, or personal injury when using this appliance, follow basic precautions, including the following:
•Do not, under any circumstances, cut or remove the third (ground) prong from the power cord. Failure to follow this warning can result in fire, explosion, or death.
•For personal safety, this dryer must be properly grounded. Failure to follow this warning can result in fire, explosion, or death.
•The power cord of this dryer is equipped with a 3-prong (grounding) plug which mates with a standard 3-prong (grounding) wall outlet
to minimize the possibility of electric shock hazard from this appliance. Failure to follow this warning can result in fire, explosion, or death.
•This dryer must be plugged into a
20-amp, 120 VAC. grounded outlet protected by a 15-ampere fuse or circuit breaker. Failure to follow this warning can result in fire, explosion,
or death.
•Where a standard 2-prong wall outlet is encountered, it is your personal responsibility and obligation to have it replaced with a properly grounded 3-prong wall outlet. Failure to follow this warning can result in fire, explosion, or death.
16
ConnecTING GAS DRYERS (cont.)
wWARNING: To reduce the risk of fire, electric shock, or personal injury when using this appliance, follow basic precautions, including the following:
•Installation and service must be performed by a qualified installer, service agency, or the gas supplier. Failure to do so can result in fire, explosion, or death.
•Use only a new stainless steel flexible connector and a new AGA-certified connector. Failure to do so can result in fire, explosion, or death.
•A gas shutoff valve must be installed within 6 ft. (1.8 m) of the dryer. Failure to do so can result in fire, explosion, or death.
•The dryer is configured for Natural Gas when shipped from the factory. Make sure that the dryer is equipped with the correct burner orifice for the type of gas being used (Natural Gas or Liquefied Petroleum). Failure to do so
can result in fire, explosion, or death.
•If necessary, the correct orifice (for the LP conversion kit order part number 383EEL3002D) should be installed by a
qualified technician and the change should be noted on the dryer. Failure to do so can result in fire, explosion, or death.
•All connections must be in accordance with local codes and regulations. Failure to do so can result in fire, explosion, or death.
•Gas dryers MUST exhaust to the outdoors.
Failure to do so can result in fire, explosion, or death.
Connecting the Gas Supply
1Make sure that the gas supply to the laundry room is turned OFF. Confirm that the type of gas available in your laundry room is
appropriate for the dryer. The dryer is prepared for Natural Gas with a 3⁄8 - inch NPT gas connection.
2Remove the shipping cap from the gas connection at the back of the dryer. Be careful not to damage the threads of the gas connector when removing the shipping cap.
3Connect the dryer to your laundry room’s gas supply using a new flexible stainless steel connector with a 3⁄8 - inch NPT fitting.
4Securely tighten all connections between the dryer and your laundry room’s gas supply. Turn on your laundry room’s gas supply and check all pipe connections (both internal and external) for gas leaks with a noncorrosive leak-detection fluid.
|
1/8" NPT Pipe |
3/8" NPT Gas |
Plug |
Connection |
Gas Supply |
|
|
AGA/CSA-Certified |
Shutoff Valve |
|
|
Stainless Steel |
|
Flexible Connector |
|
Electrical Connection
Plug dryer into a
120-VAC, 60-Hz. grounded 3-prong outlet.
High-Altitude Installations
The BTU rating of this dryer is AGA-certified for elevations below 10,000 feet.
If your gas dryer is being installed at an elevation above 10,000 feet, it must be derated by a qualified technician or gas supplier.
<![endif]>ENGLISH
17
CONNECTING ELECTRIC DRYERS
wWARNING: To help prevent fire, electric shock, serious injury, or death, the wiring and grounding must conform to the latest edition of the National Electrical Code, ANSI/NFPA 70 and all applicable local regulations. Please contact a qualified electrician to check your home’s wiring and fuses to ensure that your home has adequate electrical power to operate the dryer.
Electrical Requirements for Electric Models Only
wWARNING: To reduce the risk of fire, electric shock, or personal injury when using this appliance, follow basic precautions, including the following:
•This dryer must be connected to a grounded metal, permanent wiring system, or an equipment-grounding conductor must
be run with the circuit conductors and connected to the equipment-grounding terminal or lead on the dryer. Failure to do so can result in fire, explosion, or death.
•The dryer has its own terminal block that must be connected to a separate 240 VAC, 60 Hertz, single-phase circuit, fused at 30 amperes (the circuit must be fused on both sides of the line). ELECTRICAL SERVICE FOR THE DRYER SHOULD BE OF THE MAXIMUM RATE VOLTAGE LISTED ON THE
NAMEPLATE. DO NOT CONNECT DRYER TO 110-, 115-, OR 120-VOLT CIRCUIT. Failure to follow these instructions can result in fire, explosion, or death.
•If branch circuit to dryer is 15 ft. (4.5 m) or less in length, use UL (Underwriters Laboratories) listed No. 10 AWG wire
(copper wire only), or as required by local codes. If over 15 ft. (4.50 m), use UL-listed No.-8 AWG wire (copper wire only), or as required by local codes. Allow sufficient slack in wiring so dryer can be moved from its normal location when necessary. Failure to do so can result in fire, explosion, or death.
•The power cord (pigtail) connection between wall receptacle and dryer terminal block
IS NOT supplied with dryer. Type of pigtail and gauge of wire must conform to local codes and with instructions on the following pages. Failure to follow these instructions can result in fire, explosion, or death.
•A 4-wire connection is required for all mobile and manufactured home installations, as well as all new construction after January
1, 1996. A 4-wire connection must be used where local codes do not permit grounding through the neutral wire. Failure to do so can result in fire, explosion, or death.
wWARNING: To reduce the risk of fire, electric shock, or personal injury when using this appliance, follow basic precautions, including the following:
•Do not modify the plug and internal wire provided with the dryer.
•The dryer should be connected to a 4-hole outlet.
•If it does not fit the outlet, a proper outlet will need to be installed by a qualified electrician.
Special Electrical Requirements for Mobile or Manufactured Homes
wWARNING: To reduce the risk of fire, electric shock, or personal injury when using this appliance, follow basic precautions, including the following:
•Any installation in a manufactured or mobile home must comply with the Manufactured
Home Construction and Safety Standards Title 24 CFR, Part 32-80 or Standard CAN/
CSA0Z240 MH and local codes and ordinances.
•A 4-wire connection is required for all mobile and manufactured home installations, as well as all new construction after January 1, 1996.
Failure to do so can result in fire, explosion, or death.
18
CONNECTING ELECTRIC DRYERS (cont.)
USA ONLY
wWARNING:
•Connect the power cord to the terminal block. Each colored wire should be connected to same color screw. Wire color indicated on manual is connected to the same color screw in block. Failure to follow these instructions may result in a short or overload.
•Grounding through the neutral conductor is prohibited for: (1) new branch-circuit installations, (2) mobile homes, (3) recreational vehicles, and (4) areas where local codes prohibit grounding through the neutral conductor.
Four-Wire Connection for Electric Dryers: Power Cord
•A 4-wire connection is required for all mobile and manufactured home installations, as well as all new construction after January 1, 1996.
•A UL-listed strain relief is required.
Terminal
Block
UL-Listed
Strain Relief
UL-Listed 4-Wire Power Cord
1Remove the terminal block access cover on the upper back of the dryer. Install a UL-listed strain relief into the power cord through-hole; then thread a UL-listed, 30 A,
240 V, 4-wire, #10 AWG-minimum copper conductor power cord through the
strain relief.
•Use a 30 A, 240 V, UL-listed power cord with #10 AWG-minimum copper conductor and closed loop or forked terminals with upturned ends.
Hot |
Neutral |
Hot |
|
(White) |
|||
(Black) |
(Red) |
||
|
Ground Screw
Power Cord
Ground Wire
2Transfer the dryer’s ground wire from behind the green ground screw to the center screw of the terminal block. Attach the two hot leads of the power cord to the outer terminal block screws. Attach the white neutral wire to the center terminal block screw. Attach the power cord ground wire to the green ground screw. Tighten all screws securely. Reinstall the terminal block access cover.
<![endif]>ENGLISH
19
CONNECTING ELECTRIC DRYERS (cont.)
USA ONLY
wWARNING:
•Connect the power cord to the terminal block. Each colored wire should be connected to same color screw. Wire color indicated on manual is connected to the same color screw in block. Failure to follow these instructions may result in a short or overload.
•Grounding through the neutral conductor is prohibited for: (1) new branch-circuit installations, (2) mobile homes, (3) recreational vehicles, and (4) areas where local codes prohibit grounding through the neutral conductor.
Four-Wire Connection for Electric Dryers: Direct Wire
•A 4-wire connection is required for all mobile and manufactured home installations, as well as all new construction after January 1, 1996.
•A UL-listed strain relief is required.
1" (2.5 cm)
Ground Wire
5" (12.7 cm)
1Remove 5 inches (12.7 cm) of the outer covering from the wire. Remove 5 inches of insulation from the ground wire. Cut off
approximately 11⁄2 inches (3.8 cm) from the other three wires and strip 1 inch (2.5 cm) insulation from each wire. Bend the ends of the three shorter wires into a hook shape.
Terminal
Block
UL-Listed
Strain Relief
UL-Listed 4-Wire Power Cord
2Remove the terminal block access cover on the upper back of the dryer. Install a
UL-listed strain relief into the power cord opening; then thread the power cable prepared in Step 1 through the strain relief.
•Use UL-listed 4-wire #10 AWG-minimum copper conductor cable.
•Allow at least 5 ft. (1.5 m) length to allow for removal and reinstallation of the dryer.
Hot |
Neutral |
Hot |
|
(White) |
|||
(Black) |
(Red) |
||
|
Ground Screw
Ground
Wire
3Transfer the dryer’s ground wire from behind the green ground screw to the center screw of the terminal block. Attach the two hot leads of the power cable to the outer terminal block screws. Attach the white neutral wire to the center terminal block screw. Attach the power cable ground wire to the green ground screw. Tighten all screws securely. Reinstall the terminal block access cover.
20
CONNECTING ELECTRIC DRYERS (cont.)
USA ONLY
wWARNING:
•Connect the power cord to the terminal block. Each colored wire should be connected to same color screw. Wire color indicated on manual is connected to the same color screw in block. Failure to follow these instructions may result in a short or overload.
•Grounding through the neutral conductor is prohibited for: (1) new branch-circuit installations, (2) mobile homes, (3) recreational vehicles, and (4) areas where local codes prohibit grounding through the neutral conductor.
Three-Wire Connection for Electric Dryers: Power Cord
•A 3-wire connection is NOT permitted on new construction after January 1, 1996.
•A UL-listed strain relief is required.
Terminal
Block
UL-Listed |
Strain Relief |
UL-Listed 3-Wire Power Cord
1Remove the terminal block access cover on the upper back of the dryer. Install a UL-listed strain relief into the power cord opening; then thread a UL-listed, 30 A,
240 V, 3-wire, #10 AWG-minimum copper conductor power cord through the strain relief.
•Use a 30 A, 240 V, UL-listed power cord with #10 AWG-minimum copper conductor and closed loop or forked terminals with upturned ends.
Hot |
Neutral |
Hot |
|
(White) |
|||
(Black) |
(Red) |
||
|
Ground Screw
Ground
Wire
2Attach the two hot leads of the power cord to the outer terminal block screws. Attach the neutral wire to the center terminal block screw. Connect the external ground (if required by local codes) to the green ground screw. Tighten all screws securely. Reinstall the terminal block access cover.
<![endif]>ENGLISH
21
CONNECTING ELECTRIC DRYERS (cont.)
USA ONLY
wWARNING:
•Connect the power cord to the terminal block. Each colored wire should be connected to same color screw. Wire color indicated on manual is connected to the same color screw in block. Failure to follow these instructions may result in a short or overload.
•Grounding through the neutral conductor is prohibited for: (1) new branch-circuit installations, (2) mobile homes, (3) recreational vehicles, and (4) areas where local codes prohibit grounding through the neutral conductor.
Three-Wire Connection for Electric Dryers: Direct Wire
•A 3-wire connection is NOT permitted on new construction after January 1, 1996.
•A UL-listed strain relief is required.
1" (2.5 cm)
1Remove 31⁄2 inches (8.9 cm) of the outer covering from the wire. Strip 1 inch (2.5 cm) insulation from each wire. Bend the ends of the three wires into a hook shape.
Terminal
Block
UL-Listed
Strain Relief
UL-Listed 3-Wire Power Cord
2Remove the terminal block access cover on the upper back of the dryer. Install a UL-listed strain relief into the power cord through-hole; then thread the power cable prepared in Step 1 through the strain relief.
•Use UL-listed 3-wire #10 AWG-minimum copper conductor cable.
•Allow at least 5 ft. (1.5 m) length to allow for removal and reinstallation of the dryer.
Hot |
Neutral |
Hot |
|
(White) |
|||
(Black) |
(Red) |
||
|
Ground Screw
Ground
Wire
3Attach the two hot leads of the power cord to the outer terminal block screws. Attach the neutral wire to the center terminal block screw. Connect the external ground (if required by local codes) to the green ground screw. Tighten all screws securely. Reinstall the terminal block access cover.
22
SPECIAL REQUIREMENTS FOR MANUFACTURED OR MOBILE HOMES
Any installation in a manufactured or mobile home must comply with the Manufactured Home Construction and Safety Standards Title 24 CFR, Part 32-80 or Standard CAN/CSA0Z240 MH and local codes and ordinances. If you are uncertain whether your proposed installation will comply with these standards, please contact a service and installation professional for assistance.
•A gas dryer must be permanently attached to the floor.
•The electrical connection for an electric dryer must be a 4-wire connection. More detailed information concerning the electrical connection is provided in the section Connecting Electric Dryers.
•To reduce the risk of combustion and fire, the dryer must be vented to the outside.
•DO NOT vent the dryer under a manufactured home or mobile home.
•Electric dryers may be vented to the outside using the back, left, right, or bottom panel.
•Gas dryers may be vented to the outside using the back, left, or bottom panel. Gas dryers may not be vented to the outside using the right side panel because of the burner housing.
•The dryer exhaust duct must be affixed securely to the manufactured or mobile home structure, and the exhaust duct must be made of a material that will resist fire and combustion.
It is recommended that you use a rigid or flexible metal duct.
•DO NOT connect the dryer exhaust duct to any other duct, vent, chimney, or other exhaust duct.
•Make sure the dryer has adequate access to outside fresh air to ensure proper operation. The opening for outside fresh air must be at least 25 in2 (163 cm2).
•It is important that the clearance of the duct from any combustible construction be at least 2 inches (5 cm), and when venting the dryer to the outdoors, the dryer can be installed with a clearance of 1 inch (2.5 cm) at the sides and back of the dryer.
•Please be aware that venting materials are not supplied with the dryer. You should obtain the venting materials necessary for proper installation.
FINAL INSTALLATION CHECK
Once you have completed the installation of the dryer and it is in its final location, confirm proper operation with the following tests and Duct Condition Testing on the following page.
Testing Dryer Heating
GAS MODELS
Close the dryer door, press the ON/OFF switch to turn the dryer on, and start the dryer on a heat setting. When the dryer starts, the igniter should ignite the main burner.
NOTE: If all air is not purged from the gas line, the gas igniter may turn off before the main burner ignites. If this happens, the igniter will reattempt gas ignition after approximately
two minutes.
ELECTRIC MODELS
Close the dryer door, press the ON/OFF switch to turn the dryer on, and start the dryer on a heat setting. The exhaust air should be warm after the dryer has been operating for 3 minutes.
Checking Airflow
Effective dryer operation requires proper airflow. The adequacy of the airflow can be measured by evaluating the static pressure. Static pressure in the exhaust duct can be measured with
a manometer, placed on the exhaust duct approximately 2 ft. (60.9 cm) from the dryer. Static pressure in the exhaust duct should not exceed 0.6 inches (1.5 cm). The dryer should be checked while the dryer is running with no load.
Checking Levelness
Once the dryer is in its final location, recheck the dryer to be sure it is level. Make sure it is level front to back and side to side, and that all 4 leveling feet are firmly on the floor.
<![endif]>ENGLISH
23
DUCT CONDITION TEST
Your dryer features FlowSenseTM , an innovative sensing system that automatically detects blockages and restrictions in dryer ductwork. Keeping ductwork clean of lint buildup and free of restrictions allows clothes to dry faster and reduces energy use.
NOTE: When the dryer is first installed, this test should be performed to alert you to any existing problems with the exhaust duct in your home. However, since the test performed during normal operation provides more accurate information on the condition of the exhaust duct than does the installation test, the number of bars displayed during the two tests may not be the same.
To activate the duct condition test :
NOTE: Dryer heating test must be performed before proceeding. If heating is normal, perform cooling properly. Then perform the duct condition test below:
1Press and hold the DAMP DRY BEEP and TEMP. CONTROL buttons at the same time. While holding these buttons, press POWER ON/OFF.
2The dryer will show lnS in the number display to indicate that it is in duct condition testing mode.
3Press the START/PAUSE button. The dryer will run for approximately 2 minutes to test for blockages or restrictions to air flow in the ductwork.
If no bars are shown in the display, the ductwork is free from serious blockages or restrictions.
If all bars are lit, the dryer ductwork has a serious blockage that needs to be removed immediately.
IMPORTANT: Do NOT interrupt the test cycle!
NOTE: Even if no bars are displayed during the duct condition test, some restrictions may still be present in the exhaust dust. Refer to pages 14-15 for more information.
Check for blockages and lint buildup.
Correct Venting
Restricted or Blocked Airflow
Avoid long runs or runs with multiple elbows or bends.
Check for blockages and lint buildup.
Make sure the ductwork is not crushed or restricted.
24
CONTROL PANEL FEATURES
Following are instructions for starting and using your new dryer. Please refer to specific sections of this manual for more detailed information.
Important Warning: To reduce the risk of fire, electric shock, or personal injury, read this entire manual, including the Important Safety Instructions, before operating this dryer.
F
B
C
A |
E |
H |
G |
D |
A POWER ON/OFF BUTTON |
E |
CYCLE SETTING BUTTONS |
Press to turn the dryer ON. Press again to turn the dryer OFF.
NOTE: Pressing the ON/OFF button during a cycle will cancel that cycle and any load settings will be lost.
BCYCLE SELECTOR KNOB
Turn this knob to select the desired cycle.
Once the desired cycle has been selected, the standard presets will be shown in the display. On MANUAL DRY cycles, these settings can be adjusted using the cycle settings buttons anytime.
CSTART/PAUSE BUTTON
Press this button to START the selected cycle. If the dryer is running, use this button to PAUSE the cycle without losing the current settings.
NOTE: If you do not press the START/PAUSE button to resume a cycle within 4 minutes, the dryer automatically turns off.
DMORE TIME/LESS TIME BUTTONS
To adjust the drying time, use these buttons with MANUAL DRY, TIME DRY, and steamfresh™ cycles, as well as the reduce static and easy iron options. Press the MORE TIME button to increase the selected manual cycle time by a minute; press LESS TIME to decrease the cycle time by a minute.
Use these buttons to select the desired cycle settings for the selected cycle. The current settings are shown in the display. Press the button for that option to view and select other settings.
FTIME AND STATUS DISPLAY
The display shows the settings, estimated time remaining, options, and status messages for your dryer.
GOPTION BUTTONS
The option buttons allow you to select additional cycle options. Certain buttons feature a special function (see the following pages for details) that can be activated by pressing and holding that option button.
HSTEAM FUNCTIONS
LG’s steam technology allows you to inject fabrics with a swirling jet of hot steam to refresh clothes, reduce static, and make ironing easier. Simply select the steamfresh™ cycle.
For detailed information about the individual options, please see the following pages.
25
<![endif]>ENGLISH
OPERATING THE DRYER
26
1CLEAN THE LINT FILTER
If the lint filter has not already been cleaned, lift out the filter and remove the lint from the last load. This will help ensure the fastest and most efficient drying performance.
2LOAD THE DRYER
Load the dryer with the wet laundry from the washer.
If the load is extra large, you may need to divide it into smaller loads for proper performance and fabric care.
3TURN ON THE DRYER
Press the POWER button to turn on the dryer. The cycle LEDs will illuminate and a beep will sound, if turned on.
Refer to page 25.
4SELECT A CYCLE
Turn the Cycle Selector Knob either direction until the
LED for the desired cycle is on. The preset temperature, dry level, and option settings for that cycle will be shown. Refer to page 27.
5SELECT CYCLE MODIFIERS
Default settings for the selected cycle can now be changed if desired. This can be done using the cycle modifier buttons as shown on page 30 (temperature, dry level, and beeper).
NOTE: Not all options or modifiers are available on all cycles. A different beep will sound and the LED will not come on if the selection is not allowed.
6SELECT CYCLE OPTIONS
Cycle options can be added using the option buttons as shown on pages 31-32 (Reduce Static, Easy Iron, Child Lock and Wrinkle Care).
NOTE: Not all options or modifiers are available on all cycles. A different beep will sound and the LED.
7BEGIN CYCLE
Press the START/PAUSE button to begin the cycle. The cycle can be paused at any time either by opening the door or by pressing the START/PAUSE button. If the cycle is not restarted within 4 minutes, the dryer will shut off and the cycle settings will be lost.
8END OF CYCLE
When the cycle is finished, the chime will sound if it is set. Remove your clothing from the dryer immediately to reduce wrinkling. If Wrinkle Care is selected, the dryer will tumble briefly every few minutes to help prevent wrinkles from setting in the clothes.