LG DLG5988W, DLG5988S, DLG5988B, DLG3788W, DLE5977S Owner’s Manual
...
ElectricandGasDryer
DLE 5977W/D LG5988W
DLE 5977 B/D LG5988 B
DLE3777W/DLG3788W
Thank you for buying an LG dryer.
Pleaseread your owner's manual carefully, as it provides
instructions on safe installation, use,and maintenance.
Retain it for future reference and record the model and serial
numbers of your dryer.
P/No.: 3828EL3003A
OUTSTANDING PERFORMANCE
Not to mention unmatched big capacity, you can benefit from good
time efficiency, quiet operation and energy saving system.
STAINLESSSTEELDRUM
Stainless steel drum doesn't have any rust by nature so that
rust-free drum keeps clothes away from stain all time.
ARTISTICDESIGN
Modern front panel look and big crystal-clear glass door make your house look stylish.
DIGITALFABRICCARE
Multi-level temperature control heater takes a better care on your valued clothes.
EASYOF USE
A whole selection of user-friendly functions always make you comfortable with dryer operation.
PART1. SPECIFICATIONS ..................................................................................................................................... 3
PART2. IMPORTANT WARRANTY AND SAFETY INSTRUCTIONS ................................................................. 4-6
PART3. INITIAL STEPS FOR INSTALLING YOUR DRYER ............................................................................. 7-12
PART4. ELECTRICAL REQUIREMENTS FOR ELECTRIC DRYER ............................................................... 13-18
PART5. ELECTRICAL REQUIREMENTS FOR GAS DRYERS ............................................................................ 19
PART6. GAS REQUIREMENTS AND INSTRUCTIONS ........................................................................................ 20
PART7. EXHAUST REQUIREMENTS AND MAINTENANCE .......................................................................... 21-22
PART8. OPERATING YOUR DRYER ............................................................................................................... 23-28
PART9. TROUBLESHOOTING GUIDE ............................................................................................................ 29-31
LG DRYER LIMITED WARRANTY ........................................................................................................................ 32
2
• Name : Electric and Gas Dryer
• Power supply : Please refer to the rating label regarding detailed
information.
• Size
• Dryer capacity
• Weight(Ibs)
Specifications are subject to change by manufacturer.
--II ACESSORIES
Dryer rack (1 each)
: 68.6X98.3X76.1 (cm)
: IEC 7.3cu.ft.
: 126
Stacking kit (1 each)
Purchased Separately
Pedestal (1 each)
Purchased Separately
3
SEEKING WARRANTY ASSISTANCE
Warranty Service. The warranty for your dryer is printed the end of this manual.
Warranty service is available by contacting your nearest LG Service Center and, for warranty period
from the date of purchase, if this dryer is installed and operated according to the instructions in this
manual, LG will repair or replace any of its mechanical or electrical parts if they are defective in
material or workmanship.
WARNINGS
For your safety, the recommendations in this manual must be followed. To reduce the risk
of fire or explosion, electric shock, or to prevent property damage, personal injury, or
death when using your appliance, follow basic precautions, including the following.
Warranty Restriction: If the dryer is subjected to other than private family use, all warranty
coverage is effective for only 90 days.
You will need the complete model and serial numbers when requesting information. We recommend
that you staple your sales slip or cancelled check here, because proof of original purchase date is
needed to obtain warranty service. Your dryer's model and serial numbers are located on the Model
and Serial Number Plate located on the front of the dryer behind the door.
Use the space below to record the model number and serial number of your new LG dryer.
Model No.
Serial No.
Date of Purchase
\t/
_:_Staple your receipt hear.
IMPORTANT SAFETY INSTRUCTIONS
1) Read all instructions before using the appliance.
2) Do not dry articles that have come into contact with
gasoline, dry-cleaning solvents, or other flammable
or explosive substances, as they give off vapors that
could ignite or explode.
3) Do not allow children to play on or in the appliance.
Close supervision of children is necessary when
using the appliance.
4) Before the appliance is removed from service or
discarded, remove the door to the drying
compartment.
5) Do not reach into the appliance if the drum is
moving.
6) Do not install or store this appliance where it will be
exposed to the weather.
7) Do not tamper with controls.
SAVETHESE INSTRUCTIONS
8) Do not repair or replace any part of the appliance or
attempt any servicing unless specifically
recommended in the user-maintenance instructions.
9) Do not use heat to dry articles containing foam
rubber or similarly textured rubber-like materials.
Clean lint screen before or after each load.
10)
11)
Keep area around the exhaust opening and adjacent
surrounding areas fiee fiom the accumulation of
lint, dust, and dirt.
12) The interior of the appliance and exhaust duct
should be cleaned periodically by qualified service
personnel.
13) Do not place items exposed to cooking oils in your
dryer. Items contaminated with cooking oils may
contribute to a chemical reaction that could cause a
load to catch fire.
14) Do not use fabric soflners or products to eliminate
static unless recommended by the manufacturer of
the fabric softner or product.
GROUNDING INSTRUCTIONS
This appliance must be grounded. In the event of
malfunction or breakdown, grounding will reduce the
risk of electric shock by providing a path of least
resistance t_r electric current. This appliance is
equipped with a cord having an equipment-grounding
conductor and a grounding plug. The plug must be
plugged into an appropriate outlet that is properly
installed and grounded in accordance with all local
codes and ordinances.
WARNING - hnproper connection of the equipment-
grounding conductor can result in a risk of electric
shock. Check with a qualified electrician or service
person if you are in doubt as to whether the appliance is
properly grounded.
Do not modify the plug provided with the appliance: if
it will not fit the outlet, have a proper outlet installed by
a qualified electrician.
This appliance must be connected to a grounded metal,
permanent wiring system or an equipment-grounding
conductor must be run with the circuit conductors and
connected to the equipment-grounding terminal or lead
on the appliance.
,_ WHAT TO DO IF YOU SMELL
GAS:
• Do not try to light a match or cigarette, or turn
on any gas or electrical appliance.
• Do not touch any electrical switches. Do not
use any phone in your building.
• Clear the room, building or area of all
occupants.
• Immediately call your gas supplier from a
neighbor's phone. Follow the gas supplier's
instructions carefully.
• If you cannot reach your gas supplier, call the
fire department.
_Ik WARNING
To reduce the risk of fire or explosion, electric
shock, property damage, personal injury or death
when using this appliance, please follow all
instructions and information, including those in
this manual and instructions and information
provided by your gas supplier, including the
following:
• Do not store or use any gasoline, dry-cleaning
solvents any other flammable vapors or
liquids in the area surrounding this appliance.
• Do not dry anything that has ever had anything
flammable on it, even after washing.
• No washer can completely remove oil. Do not
dry any articles that have ever had any kind of
oil on them, including cooking oil.
WARNING!
• Keep flare mable materials and vapors, such
as gasoline, away from dryer.
• Place dryer at least 18 inches above the floor
for a garage installation.
• Failure to do so can result in death,
explosion or fire.
California safe drinkinq water and
toxic enforcement act
This act requires the governor of California to
publish a list of substances known to the state to
cause cancer, birth defects or other reproductive
harm and requires businesses to warn customers
of potential exposure to such substances.
Gas appliances can cause minor exposure to four
of these substances, namely benzene, carbon
monoxide, formaldehyde and soot, caused
primarily by the incomplete combustion of
natural gas or LP fuels.
Properly adjusted dryers will minimize
combustion. Exposure to these substances can be
minimized further by properly venting the dryer
to the outdoors.
• Articles containing foam, rubber, rubber-like
materials, plastic or similar materials should be
dried on a clothesline or by using an air cycle.
• Failure to follow these instructions can result in
fire, death or serious injury.
• A qualified service person or company must
perform installation and service of this
appliance.
6
The following instructions will help guide you through the initial steps of setting up your dryer for use.
Please note that every section of this manual provides important information regarding the preparation and
use of your dryer, and it is important that you review this entire manual before proceeding with any
installation or use. More detailed instructions concerning electrical connections, gas connections, and
exhaust requirements are provided at other parts of this manual.
STEP 1" Positioning the Dryer.
Choose a location with a solid floor for your dryer.
Place the dryer at least eighteen inches above the
floor for a garage installation. After placing the
dryer in the desired location, please confirm that the
dryer has the required clearances through reference
to the following information and manual sections on
Exhaust Requirements and Maintenance.
If you are installing your dryer in a manufactured or
mobile home, please refer to STEP 9 below for
additional instructions.
_EZZZ]-
(98.3 crn)
Installing Your Dryer in a Closet or Recessed
Area. Following are instructions concerning and the
minimum clearances required for any closet, recessed
area, or customized under-counter installation:
• Additional spacing should be considered for
installation and servicing.
• Additional clearances might be required for wall,
door, and floor moldings.
• Additional spacing of 1 in. (2.5 cm) on all sides of
the dryer is recommended to reduce noise transfer.
For closet installation with a door, minimum
ventilation openings in the top and bottom of the
door are required. Louvered doors with equivalent
ventilation openings are acceptable. Companion
appliance spacing should also be considered.
3" _¸
(7.6cm)
48"2 jJl
(310cm_)
18"
(45.72 crn)
38.7" !
1
(68.6cm) / -- (76.1cm)
* Most installations require a minimum 5 1/2in.
(14 cm) clearance behind the dryer for the exhaust
vent with elbow.
24,,211!
(7.6cm)
(2.54 cm) (76.1 cm) (2.54 crn)
<Closet door with ventilation hole.> <Side view-closet or conined area.>
0 '__ 27" _'q_0"
(0 cm) (68.6 cm) (0 cm)
<Recessed Area>
_ 29196" _
=E::::::::3=
Oncein position,adjustthelevelinglegsof thedryer
untilitislevelfromlefttorightandfromfrontto
back.Thelevelinglegsmustremainfirmlyonthe
floorandthedryershouldnotrock.Themaximum
slopeofthedryerfromlefttorightorfromfrontto
backshouldnotexceed2.5cm(1inch).If thedryer
isnotlevel,andif theslopeexceeds2.5cm(1inch),
aloadmaynottumbleproperlyandinternalsensors
maymalfunction.Note:Othersectionsofthis
manualalsoprovideimportantinformation
concerningtheplacementofandclearancesforyour
dryer.Pleasereviewthisentiremanualbefore
proceedingwithanyinstallation.
STEP 2: Procedure for Reversing
the Door
The door on your dryer can be installed to open
either to the left or the right. Follow these
procedures to reverse the direction in which your
door opens:
STEP 3: Connecting the Exhaust
and Venting System.
In addition to the following warnings, please refer
to manual section on Exhaust Requirements and
Maintenance. IMPORTANT." To reduce the risk of
fire, combustion, and gas accumulation, the dryer
must be vented to the outdoors. Please follow the
instructions (and all others in this manual) very
carefully.
• ALTERNATE EXHAUST DIRECTIONS
1.Remove screw & exhaust duct.
'3
/_,, Detach and remove the bottom, left, or right
side knockout as desired.
(Right side vent not avitable on gas dryer.)
f PORTION A i "_
®
hol_)
\ (#
J
• Do not use thin plastic or foil ducting.
• Use 4" (10.2 cm) diameter rigid or flexible metal
duct (note: venting materials are not supplied with
the dryer, and you should obtain the venting
materials necessary for proper installation)
• Position the dryer where the exhaust duct is
shorter as possible
• Clean old ducts beJbre installing this dryer
• The male end of each section of exhaust duct must
point away from the dryer
• Use fewer elbow joints as possible
• Use duct tape on all duct joints
• Insulate ductwork that runs through unheated
areas in order to reduce condensation and lint
build-up on pipe walls; and
• PLEASE BE AWARE THAT FAILURE TO
EXHAUST THE DRYER CORRECTLY WILL
VOID THE DRYER'S WARRANTY.
WARNING!
• Use a heavy metal vent.
• Do not use a plastic vent.
• Do not use a metal foil vent.
• Failure to follow these instructions can
result in death or fire.
• Clean old ducts before installing this dryer
3, Reconnect the new duct[11 in(28cm)] to the
blower housing, and Fixing the duct to the
base.
4.Pre-assembte 4" elbow with 4" duct.
Wrap duct tape around joint.
DUCT
TAPE
5. Insert elbow duct assembly first, through the
side opening and connect the elbow to the
dryer internal duct.
J
STEP 4: Connection of Gas Supply
(Gas dryer only). In addition to the following,
please refer to manual section on Gas Requirements
and Instructions.
ii i
1. New stainless steel flexible connector. Use this type of
connector only if allowed by local codes. Use Design AGA
Certified Connector.
2. 1/8" NPT Pipe Plug (for checking inlet gas pressure)
3. Equipment Shut-Off Valve-
Installed within 6' ( 1.8 m) of dryer
4. Iron Pipe. Shorter than 20' (6,1 m)
Use 3/8" pipe. Longer than 20' (6.1 m) - Use 1/2" pipe.
5.3/8" N.P.T. Gas Conuection
1. Confirm that the type of gas available in your
laundry room is appropriate for the dryer. The
dryer is prepared for Natural Gas with a 3/8"
NPT gas connection.
2. Remove the shipping cap from the gas
connection at the back of the dryer. Make sure
that you don't damage the threads of the gas
connection pipe when you remove the shipping
cap.
3. Connect the dryer to your laundry room's gas
supply using a new flexible stainless steel
connector (as noted below, only use a new
stainless steel flexible connector if allowed by
your local codes).
4. Securely tighten all connections between the
dryer and your laundry room's gas supply. Turn
on your laundry room's gas supply and check all
pipe connections (both internal and external) for
gas leaks with a non-corrosive leak detection
fluid.
5. For LP (Liquefied Petroleum) gas connection,
refer to this manual's section entitled Gas
Requirements and Instructions.
10
STEP 5: Electrical Plug Connections
for Electric Dryer Only•
Following are several warnings and instructions
concerning making the electrical connection for
electric dryers. More detailed information
concerning the electrical connection is provided at
the manual section entitled Electrical Requirements
For Electric Dryer and it is important that you
thoroughly review that section, and the remainder of
this manual, before taking any steps to install or use
this dryer.
1. Use only a new U.L. listed No. 10 (copper wire
only) three conductor power supply cord kit rated
240 Volts (minimum) 30 Amperes and labeled as
suitable for use in a clothes dryer.
2. Four-wire cord is requited for manufactured
(mobile) home installations and use and where
local codes do not allow grounding of this
appliance through neutral.
3. Thc wiring diagram is providcd insidc thc drycr
control hood. Label all wires prior to
disconnection when servicing the dryer, because
wiring errors can cause serious injury to you and
your dryer.
4. For additional instruction on connecting the dryer
to an electrical power source, please refer to this
manual's section on Electrical Requirements and
Electric Dryer.
WARNING!
• Use a new UL approved 30 amp power
supply cord or 10 gauge solid copper wire.
• Use a UL approved strain relief.
• Disconnect power before making electrical
connections.
•Connect neutral wire(wh ite or center wire) to
center terminal.
• Ground wire(green or bare wire) must be
connected to green ground connector.
• Securely tighten all electrical connections
• See installation instructions for complete
instructions.
• Failure to do so can result in fire or electrical
shock.
Loading...