LG DF22VV2SBG Owner's manual

OWNER’S MANUAL

DRYER

ENGLISH ESpañoL

Read this owner’s manual thoroughly before operating the appliance and keep it handy for reference at all times.

DF22WV2E, DF22WV2G DF22VV2SBE, DF22VV2SBG

MFL67652528

Rev.01_112818

www.lg.com

TABLE OF CONTENTS

IMPORTANT SAFETY INSTRUC-

TIONS

3 WHAT TO DO IF YOU SMELL GAS 4 BASIC SAFETY PRECAUTIONS 5 GROUNDING INSTRUCTIONS 5 SAFETY INSTRUCTIONS FOR INSTALLATION 7 SAFETY INSTRUCTIONS FOR CONNECTING

ELECTRICITY

PRODUCT FEATURES

PRODUCT OVERVIEW

9 Parts 9 Accessories

INSTALLATION

10 Installation Overview 10 Product Specifications 11 Installation Location Requirements 12 Clearances 14 Leveling the Dryer 15 Reversing the Door 16 Installing the Side Vent Kit 17 Stacking the Dryer 18 Venting the Dryer 20 Connecting the Inlet Hose (Steam Models) 21 Connecting Gas Dryers 23 Connecting Electric Dryers 27 Final Installation Check 28 Installation Test (Duct Check)

OPERATION

30 Using the Dryer 31 Check the Lint Filter Before Every Load 31 Sorting Loads 31 Loading the Dryer 32 Control Panel 35 Cycle Guide 39 Cycle Settings and Options

SMART FUNCTIONS

43 LG SmartThinQ Application 46 Smart Diagnosis™ Function

MAINTENANCE

47 Regular Cleaning

TROUBLESHOOTING

48 FAQs: Frequently Asked Questions 49 Before Calling for Service

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USE

WARNING

For your safety, the information in this manual must be followed to minimize the risk of fire, explosion, or electric shock, or to prevent property damage, injury to persons, or death.

Your safety and the safety of others is very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word DANGER, WARNING, or CAUTION.

These words mean:

DANGER WARNING

You will be killed or seriously injured if you don’t immediately follow instructions.

- You can be killed or seriously injured if you don’t follow instructions.

ENGLISH

CAUTION

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

•Do not install a clothes dryer with flexible plastic venting materials. If flexible metal (foil type) duct is installed, it must be of a specific type identified by the appliance manufacturer as suitable for use with clothes dryers. Flexible venting materials are known to collapse, be easily crushed, and trap lint. These conditions will obstruct clothes dryer airflow and increase the risk of fire.

•Install the clothes dryer according to the manufacturer’s instructions and local codes.

•Save these instructions.

- You may be slightly injured or cause damage to the product if you do not follow instructions.

WARNING

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly could result in serious injury, death or property damage.

- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

WHAT TO DO IF YOU SMELL GAS

•Do not try to light any appliance.

•Do not touch any electrical switch; do not use any phone in your building.

•Clear the room, building or area of all occupants.

•Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

•If you cannot reach your gas supplier, call the fire department.

- Installation and service must be performed by a qualified installer, service agency or the gas supplier.

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USE

WARNING

For your safety, the information in this manual must be followed to minimize the risk of fire, explosion, or electric shock, or to prevent property damage, injury to persons, or death.

BASIC SAFETY PRECAUTIONS

WARNING

To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions, including the following:

•Read all instructions before using the dryer.

•Before use, the dryer must be properly installed as described in this manual.

•Do not place items exposed to cooking oils in your dryer. Items contaminated with cooking oils may contribute to a chemical reaction that could cause a load to catch fire.

•Do not dry articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, dry-cleaning solvents, or other flammable or explosive substances as they give off vapors that could ignite or explode.

•Do not reach into the dryer if the drum or any other part is moving.

•Do not repair or replace any part of the dryer or attempt any servicing unless specifically recommended in this owner’s manual or in published user-repair instructions that you understand and have the skills to carry out.

•Do not tamper with controls.

• Before the dryer is removed from service or discarded, remove the door to the drying compartment.

•Do not allow children to play on or in the dryer. Close supervision of children is necessary when the dryer is used near children.

•This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

•Children should be supervised to ensure that they do not play with the appliance.

•Do not use fabric softeners or products to eliminate static unless recommended by the manufacturer of the fabric softener or product.

•Do not use heat to dry articles containing foam rubber or similarly textured rubber-like materials.

•Keep area around the exhaust opening and adjacent surrounding areas free from the accumulation of lint, dust, and dirt.

•It should not be operated if chemical products are used for cleaning.

•The interior of the dryer and exhaust vent should be cleaned periodically by qualified service personnel.

•Do not install or store the dryer where it will be exposed to the weather.

•Always check the inside of the dryer for foreign objects.

•Clean lint screen before or after each load.

•Do not store plastic, paper, or clothing that

may burn or melt on top of the dryer during operation.

•Be careful when opening and closing the door. Fingers and hands can get caught in the door and cause injury if the door drops forward unexpectedly.

•Do not place heavy items on or lean against the

top of the door when it is open.

•Do not attempt to pull the hamper door open

more than 40 degrees.

• The dryer could tip forward, causing injury or damage.

•Do not place items on the top of the dryer.

•Certain internal parts are intentionally not grounded and may present a risk of electric shock only during servicing. Service personnel - do not contact the following parts while the appliance is energized: valve, motor, control board, heater, generator.

WARNING

Never stop a tumble dryer before the end of the drying cycle unless all items are quickly removed and spread out so that the heat is dissipated.

•Exhaust air must not be discharged into a flue which is used for exhausting fumes from appliances burning gas or other fuels.

•The appliance must not be installed behind a lockable door, a sliding door or a door with a hinge on the opposite side to that of the tumble dryer.

•Items such as foam rubber (latex foam), shower caps, waterproof textiles, rubber backed articles and clothes or pillows fitted with foam rubber pads should not be dried in the tumble dryer.

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USE

WARNING

For your safety, the information in this manual must be followed to minimize the risk of fire, explosion, or electric shock, or to prevent property damage, injury to persons, or death.

GROUNDING INSTRUCTIONS

This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This appliance must be equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

WARNING

Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service person if you are in doubt that the appliance is properly grounded.

Do not modify the plug provided with the appliance. If it will not fit the outlet, have a proper outlet installed by a qualified electrician. This appliance must be connected to a grounded metal, permanent wiring system or an equipmentgrounding conductor must be run with the circuit conductors and connected to the equipmentgrounding terminal or lead on the appliance. Electric shock can result if the dryer is not properly grounded.

ENGLISH

SAFETY INSTRUCTIONS FOR INSTALLATION

WARNING

To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions, including the following:

•Properly ground dryer to conform with all governing codes and ordinances. Follow details

in the installation instructions. Electric shock can result if the dryer is not properly grounded.

•Before use, the dryer must be properly installed as described in this manual. Electric shock can result if the dryer is not properly grounded.

• Install and store the dryer where it will not be exposed to temperatures below freezing or exposed to the weather.

•All repairs and servicing must be performed by an authorized servicer unless specifically recommended in this owner’s manual. Use only authorized factory parts. Failure to follow

this warning can cause serious injury, fire, electric shock, or death.

• To reduce the risk of electric shock, do not install the dryer in humid spaces. Failure to follow this warning can cause serious injury, fire, electric shock, or death.

•Connect to a properly rated, protected, and sized power circuit to avoid electrical overload.

Improper power circuit can melt, creating electric shock and/or fire hazard.

•Remove all packing items and dispose of all shipping materials properly. Failure to do so can

result in death, explosion, fire, or burns.

•Place dryer at least 18 inches above the floor for a garage installation. Failure to do so can

result in death, explosion, fire, or burns.

•Keep all packaging from children. Packaging material can be dangerous for children. There is a risk of suffocation.

•Do not install near another source of heat such as a stove, cooking oven. Failure to do so can

cause deform, smoke and fire.

•Do not place candles, smoking materials, or other flammables on top of the product. Dripping

wax, smoke, or fire can result.

•Remove all protective vinyl film from the product. Failure to do so can cause product

damage, smoke or fire.

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USE

WARNING

For your safety, the information in this manual must be followed to minimize the risk of fire, explosion, or electric shock, or to prevent property damage, injury to persons, or death.

SAFETY INSTRUCTIONS FOR INSTALLATION

WARNING

To reduce the risk of injury to persons, follow all industry recommended safety procedures including the use of long sleeved gloves and safety glasses. Failure to follow all of the safety warnings in this manual could result in property damage, injury to persons, or death.

Exhaust/Ducting:

•Gas dryers MUST be exhausted to the outside. Adequate ventilation must be provided to prevent the return of gas flow into the room, from other appliances that burn other fuels, including open burners. Failure to follow these

instructions can result in fire or death.

•The dryer exhaust system must be exhausted to the outside of the dwelling. If the dryer is not exhausted outdoors, some fine lint and large amounts of moisture will be expelled into the laundry area. An accumulation of lint in any area of

the home can create a health and fire hazard.

•Use only rigid, semi-rigid, or flexible metal 4-inch diameter ductwork inside the dryer cabinet or for exhausting to the outside. Use of plastic or other combustible ductwork can cause a fire. Punctured ductwork can cause a fire

if it collapses or becomes otherwise restricted in use or during installation.

•Ductwork is not provided with the dryer, and you should obtain the necessary ductwork locally. The end cap should have hinged dampers to prevent backdraft when the dryer is not in use. Failure to follow these instructions can

result in fire or death.

•The exhaust duct must be 4 inches (10.2 cm) in diameter with no obstructions. The exhaust duct should be kept as short as possible. Make sure to clean any old ducts before installing your new dryer. Failure to follow these instructions

can result in fire or death.

•Fabric softeners, or similar products, should be used as specified by the fabric softener instructions.

•Remove all objects from pockets such as lighters and matches.

•Rigid, semi-rigid, or flexible metal ducting is recommended for use between the dryer and the wall. All non-rigid metal transition duct must be UL-listed. Use of other materials for transition ducting could affect drying time.

Failure to follow these instructions can result in fire or death.

•DO NOT use sheet metal screws or other fasteners which extend into the duct that could catch lint and reduce the efficiency of the exhaust system. Secure all joints with duct

tape. For complete details, follow the Installation Instructions. Failure to follow these instructions can result in fire or death.

WARNING

Fire Hazard

Failure to follow safety warnings exactly could result in serious injury, death or property damage.

Do not install a booster fan in the exhaust duct. Install all clothes dryers in accordance with the

installation instructions of the manufacturer of the dryer.

WARNING

Never stop a tumble dryer before the end of the drying cycle unless all items are quickly removed and spread out so that the heat is dissipated.

a. For appliances with ventilation openings in

the base, that a carpet must not obstruct the openings.

b. Exhaust air must not be discharged into a

flue which is used for exhausting fumes from appliances burning gas or other fuels.

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USE

WARNING

For your safety, the information in this manual must be followed to minimize the risk of fire, explosion, or electric shock, or to prevent property damage, injury to persons, or death.

SAFETY INSTRUCTIONS FOR CONNECTING ELECTRICITY

WARNING

To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions, including the following:

•Do not, under any circumstances, cut or remove the ground prong from the power cord.

To prevent injury to persons or damage to the dryer, the electrical power cord must be plugged into a properly grounded outlet.

•For personal safety, this dryer must be properly grounded. Failure to do so can result in electric

shock or injury.

•Refer to the installation instructions in this manual for specific electrical requirements for your model. Failure to follow these instructions

can create an electric shock hazard and/or a fire hazard.

•This dryer must be plugged into a properly grounded outlet. Electric shock can result if the dryer is not properly grounded. Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly grounded. Failure to follow these instructions

can create an electric shock hazard and/or a fire hazard.

•If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

•The dryer should always be plugged into its own individual electrical outlet which has a voltage rating that matches the rating plate. This

provides sparkling performance and also prevents overloading house wiring circuits which could cause a fire hazard from overheated wires.

•Never unplug your dryer by pulling on the power cord. Always grip plug firmly and pull straight out from the outlet. The power cord can

be damaged, resulting in a risk of fire and electric shock.

•Repair or replace immediately all power cords that have become frayed or otherwise damaged. Do not use a cord that shows cracks or abrasion damage along its length or at either end. The power cord can melt, creating an electric

shock and/or fire hazard.

•When installing or moving the dryer, be careful not to pinch, crush, or damage the power cord.

This will prevent injury and prevent damage to the dryer from fire and electric shock.

ENGLISH

SAVE THESE INSTRUCTIONS

PRODUCT FEATURES

EASY-TO-USE CONTROL PANEL

Rotate the cycle selector knob to select the desired dry cycle. Add cycle options or adjust settings with the touch of a button.

EASY-ACCESS REVERSIBLE DOOR

The wide-opening door provides easy access for loading and unloading. The door hinge can be reversed to adjust for installation location.

STEAM FUNCTIONS(STEAM MODELS)

LG’s steam technology allows you to inject fabrics with a swirling jet of hot steam to refresh clothes, reduce static. Simply select the Steam Fresh™ cycle, you can add a Steam option to selected cycles.

Flow Sense™ DUCT BLOCKAGE SENSING SYSTEM INDICATOR

The Flow Sense™ duct blockage sensing system detects and alerts you to restrictions in the installed household ductwork that reduce exhaust airflow through the dryer. If you see the alert: Clean or repair the ducts to remove the restrictions. Keep your ducts clean to help increase efficiency and reduce long drying times caused by blocked ducts.

Smart Diagnosis™

Should you experience any technical difficulty with your washing machine, it has the capability of transmitting data by phone to the Customer Information Center. The call center agent records the data transmitted from your machine and uses it to analyze the issue, providing a fast and effective diagnosis.

Smart ThinQ™

Download the new LG smart phone app to set options, self-diagnose and troubleshoot problems with the appliance, and other useful features. This function uses Wi-Fi.

PRODUCT OVERVIEW

Parts

Reversible door

Control

panel

Lint

lter

Leveling

feet

Accessories

Included Accessories Optional Accessories

Power Cord

(gas models)

Gas connection

(gas models)

Exhaust Duct Outlet

ENGLISH

Terminal Block Access Panel (electric models)

Water inlet valve (on some models)

Y connector

(Steam Models)

Hoses

(Steam Models)

Drying Rack

(on some models)

Pedestal

(sold separately)

Side vent kit

(sold separately)

Kit No. 383EEL9001B

Stacking kit

(sold separately)

NOTE

•For your safety and for extended product life, use only authorized components. The manufacturer is not responsible for product malfunction or accidents caused by the use of separately purchased unauthorized components or parts.

•The images in this guide may be different from the actual components and accessories, which are subject to change by the manufacturer without prior notice for product improvement purposes.

INSTALLATION

Installation Overview

Please read the following installation instructions first after purchasing this product or transporting it to another location.

Check and choose the proper location

Gas dryer

Plug in the power cord

(steam models)

Electric dryer

Level the dryer

Encendido/

Apagado

(Power)

Installation test Test run

Vent the dryer

Connect gas dryersConnect the inlet hose

Connect electric dryers

Product Specifications

The appearance and specifications listed in this manual may vary due to constant product improvements.

Dryer Models DF22WV2E / DF22WV2G DF22VV2SBE / DF22VV2SBG

Description Non-steam Dryer Steam Dryer

Electrical requirements

Gas : 120 V~ 60 Hz 400 W Elec : 120/240 V~ 60 Hz 5550W

Gas requirements

Dimensions

Net weight

Steam Cycle - IEC 7.4 cu.ft. (8 lb/3.6kg)

Drying Capacity

Normal Cycle 210L , IEC 7.4 cu.ft. (Dry Clothes 13kg / Wet Clothes 20kg)

NOTE

Model numbers can be found on the cabinet inside the door.

NG: 4 - 10.5-inch (10.2 - 26.7 cm) WC LP: 8 - 13-inch (20.4 - 33.1 cm) WC

27” (W) X 30.2” (D) X 39” (H), 51.4” (D with door open)

68.6 cm (W) X 76.5 cm (D) X 99 cm (H), 130.5 cm (D with door open)

Gas : 123.02 lb (55.8kg) - 126.77 lb (57.5kg) Electric : 120.15 lb (54.5kg) - 123.46 lb (56kg)

INSTALLATION

Installation Location Requirements

WARNING

Read all installation instructions completely before installing and operating the dryer! It is important that you review this entire manual before installing and using the dryer. Detailed instructions concerning electrical connections, gas connections, and exhaust requirements are provided on the following pages.

The installation requires:

•A location that allows for proper exhaust installation. A gas dryer must be exhausted to the outdoors. See Venting the Dryer.

•A grounded electrical outlet located within 2 ft. (61 cm) of either side of the dryer. See Connecting Electric Dryers .

•A sturdy floor to support the total dryer weight of 200 lb (90.7 kg). The combined weight of a companion appliance should also be considered.

•No other fuel-burning appliance can be installed in the same closet as a dryer.

Do not operate the dryer at temperatures below 45 °F (7 °C). At lower temperatures, the dryer might not shut off at the end of an automatic cycle. This can result in longer drying times. The dryer must not be installed or stored in an area where it will be exposed to water and/or weather. Check code requirements. Some codes limit, or do not permit, installation of the dryer in garages, closets, mobile homes or sleeping quarters. Contact your local building inspector.

NOTE

•The floor must be level, with a maximum slope of 1 inch (2.5 cm) under the entire dryer. Clothes may not tumble properly, and automatic sensor cycles may not operate correctly if dryer is not level.

•For a garage installation, you will need to place the dryer at least 18 inches (46 cm) above the floor. The standard pedestal is 15 inches (38.1 cm). You will need 18 inches (46 cm) from the garage floor to the bottom of the dryer.

ENGLISH

(155 cm

Vent Requirements

INSTALLATION

Clearances

48 in.

(310 cm

24 in.

)

Closet Door

1"* (25 mm)

(76 mm)

1" (25 mm)

18" min.* (457 mm)

30.2" (765mm)

14" max.* (356 mm)

5"** (127 mm)

27" (686 mm)

1" (25 mm)

1"* (25 mm)

0" (0 mm)

30.2"

39" (990 mm)

14" max.* (356 mm)

18" min.* (457 mm)

(765mm)

1" (25 mm)

5"** (127 mm)

27" (686 mm)

1" (25 mm)

Installation Spacing for Recessed Area or Closet Installation

The following spacing dimensions are recommended for this dryer. This dryer has been tested for clearances of 1 inch (2.5 cm) on the sides and rear. Recommended clearances should be considered for the following reasons:

•Additional clearances should be considered for ease of installation and servicing.

•Additional clearances might be required for wall, door and floor moldings.

•Additional clearances should be considered on all sides of the dryer to reduce noise transfer. For closet installation, with a door, minimum ventilation openings in the top and bottom of the door are required. Louvered doors with equivalent ventilation openings are acceptable.

•Companion appliance spacing should also be considered.

INSTALLATION

Closet Ventilation Requirements

Closets with doors must have both an upper and lower vent to prevent heat and moisture buildup in the closet. One upper vent opening with a minimum opening of 48 sq. in. (310 cm

) must be installed no lower than 6 feet above the floor. One lower vent opening with a minimum opening of 24 sq. in. (155 cm2) must be installed no more than one foot above the floor. Install vent grills in the door or cut down the door at the top and bottom to form openings. Louvered doors with equivalent ventilation openings are also acceptable.

NOTE

There should be at least a little space around the dryer (or any other appliance) to eliminate the transfer of vibration from one appliance to another. If there is enough vibration, it could cause appliances to make noise or come into contact, causing paint damage and further increasing noise.

Installation Spacing for Recessed Area or Closet, with Stacked Washer and Dryer

6"*

(152 mm)

771/2"

(1968 mm)

48 in.

(310 cm2)

3"*

(76 mm)

ENGLISH

24 in.

(155 cm2)

3"*

(76 mm)

1"*

(25 mm)

/2"

(140 mm)

1"*

(25 mm)

27"

(686 mm)

* Required spacing ** For side or bottom venting, 2-inch (5.1 cm) of spacing is allowed.

Installation Spacing for Cabinet

For cabinet installation with a door, minimum ventilation openings in the top of the cabinet are required. * Required spacing

(178 mm)

9"*

(229 mm)

1"*

(25 mm)

5"*

(127 mm)

30.2"*

(765 mm)

1"* (25 mm)

1"*

(25 mm)

27"*

(686 mm)

1"* (25 mm)

INSTALLATION

Leveling the Dryer

WARNING

To reduce the risk of injury to persons, adhere to all industry recommended safety procedures including the use of long-sleeved gloves and safety glasses. Failure to follow this warning may result in serious injury or death.

•The appliance is heavy. Two or more people are required when installing the dryer. Failure to follow this warning may result in serious injury or death.

•To ensure that the dryer provides optimal drying performance, it must be level. To minimize vibration, noise, and unwanted movement, the floor must be a perfectly level, solid surface.

NOTE

Adjust the leveling feet only as far as necessary to level the dryer. Extending the leveling feet more than necessary may cause the dryer to vibrate.

Position the dryer in the final location. Check

levelness of dryer from side to side. Repeat from front to back.

Use an adjustable wrench to turn the leveling

feet. Unscrew the legs to raise the dryer or screw in the legs to lower it. Raise or lower with the leveling feet until the dryer is level from side to side and front to back. Make sure that all four leveling feet are in firm contact with the floor.

If you are installing the dryer on the optional pedestal, you must use the leveling feet on the pedestal to level the dryer. The dryer leveling feet should be fully retracted.

Level

Leveling Feet

•All four leveling feet must rest solidly on the floor. Gently push on the top corners of the dryer to make sure that the dryer does not rock from corner to corner.

INSTALLATION

Reversing the Door

Tools Required

Phillips or large flat-blade screwdriver (for hinge screws) Small flat-blade screwdriver (for lifting out parts)

WARNING

The dryer door is very large and heavy.

Failure to follow the instructions below can result in damage to the dryer, property damage or personal injury.

•To avoid damage to the dryer or the door, support the door with a stool or box that fits under the door, or have an assistant support the weight of the door.

•Avoid dropping the door to prevent damage to the door or the floor.

•Unplug the dryer or turn off power at the main circuit breaker before beginning door reversal.

•Always reverse the door BEFORE stacking the dryer on top of the washer.

Door Reversal Instructions

NOTE

The instructions here are for changing the door swing from a right to a left side hinge. If the door has been reversed, and it is necessary to change it back, use care when following these instructions. Some of the illustrations and the left/right references will be reversed, and you will need to read the instructions carefully.

While supporting the door, remove the 2 screws

on the door hinge. Remove the door.

Turn the door upside down and line up the holes

in the hinge with the holes on the opposite side of the cabinet. Reinstall the door with the screws removed in step 2.

WARNING

•Be sure to support the weight of the door before installing the hinge screws.

Install the two decorative screws, the latch,

and two latch screws removed in step 1 on the opposite side from which they were removed.

ENGLISH

Open the door and remove the two decorative

screws, two latch screws, and the latch on the catch side with a screwdriver. Save these for step 4.

Check that the door closes properly.

INSTALLATION

Installing the Side Vent Kit

WARNING

•Use a heavy metal vent.

•Do not use plastic or thin foil ducts.

•Clean old ducts before installing this dryer.

•To reduce the risk of injury to persons, adhere to all industry recommended safety procedures including the use of long-sleeved gloves and safety glasses.

•Failure to follow all of the safety warnings in this manual could result in property damage, injury to persons, or death.

The dryer is shipped to vent to the rear. It can also be configured to vent to the bottom or side (right-side venting is not available on gas models).

An adapter kit, part number 383EEL9001B, may be purchased from an LG retailer. This kit contains the necessary duct components to change the dryer vent location.

Remove the rear exhaust duct retaining screw.

Pull out the exhaust duct.

Retaining Screw

Preassemble a 4-inch (10.2 cm) elbow to the

next 4-inch (10.2 cm) duct section, and secure all joints with duct tape. Be sure that the male end of the elbow faces AWAY from the dryer. Insert the elbow/duct assembly through the side opening and press it onto the adapter duct. Secure it in place with duct tape. Be sure that the male end of the duct protrudes 1½ inches (3.8 cm) to connect the remaining ductwork. Attach the cover plate to the back of the dryer with the included screw.

Cover Plate

Elbow

(3.8 cm)

Option 2: Bottom Venting

Press the adapter duct onto the blower housing

and secure it to the base of the dryer as shown.

Adapter Duct

Rear Exhaust Duct

Option 1: Side Venting

Press the tabs on the knockout and carefully

remove the knockout for the desired vent opening (right-side venting is not available on gas models). Press the adapter duct onto the blower housing and secure to the base of the dryer as shown.

Adapter Duct

Bracket

Knockout

Bracket

Insert the 4-inch (10.2 cm) elbow through the

rear opening and press it onto the adapter duct. Be sure that the male end of the elbow faces down through the hole in the bottom of the dryer. Secure it in place with duct tape. Attach the cover plate to the back of the dryer with the included screw.

Cover Plate

Elbow

INSTALLATION

Stacking the Dryer

Stacking Kit Installation

This stacking kit includes:

•Two (2) side rails

•One (1) front rail

•Four (4) screws

Tools Needed for Installation:

•Phillips screwdriver

WARNING

To reduce the risk of electrical shock, fire, explosion, property damage, serious injury or death, follow basic precautions, including the following:

•The weight of the dryer and the height of installation make this stacking procedure too risky for one person. Two or more people are required when installing the stacking kit.

•Do not use the stacking kit with a gas dryer in potentially unstable conditions such as a mobile home.

•Place the washer on a solid, stable, level floor capable of supporting the weight of both appliances.

•Do not stack the washer on top of the dryer.

•If appliances are already installed, disconnect them from all power, water, or gas lines and from draining or venting connections.

To ensure safe and secure installation, please observe the following instructions.

Make sure the surface of the washer is clean

and dry. Remove paper backing from the tape on one of the stacking kit side brackets.

Fit the side bracket to the side of the washer top

as shown in the below illustration. Firmly press the adhesive area of the bracket to the washer surface. Secure the side bracket to the washer with a screw on the back side of the bracket. Repeat steps 1 and 2 to attach the other side bracket.

Place the dryer on top of the washer, fitting the

dryer feet into the side brackets as illustrated. Avoid finger injuries; do not allow fingers to be pinched between the washer and dryer.

Slowly slide the dryer toward the back of the washer until the side bracket stoppers catch the dryer feet.

Insert the front rail between the bottom of the

dryer and the top of the washer. Push the front rail toward the back of the washer until it comes in contact with the side rail stoppers.

Install the two remaining screws to secure the front rail to the side rails.

ENGLISH

INSTALLATION

Venting the Dryer

WARNING

To reduce the risk of fire or explosion, electric shock, property damage, injury to persons or death when using this appliance, follow basic safety precautions, including the following:

•Do not crush or collapse ductwork. Failure to follow these instructions may result in fire or death.

•Do not allow ductwork to rest on or contact sharp objects. Failure to follow these instructions may result in fire or death.

•If connecting to existing ductwork, make sure it is suitable and clean before installing the dryer. Failure to follow these instructions may result in fire or death.

•Venting must conform to local building codes. Failure to follow these instructions may result in fire or death.

•Gas dryers MUST exhaust to the outdoors. Failure to follow these instructions may result in fire or death.

•Use only 4-inch (10.2 cm) rigid, semi-rigid or

flexible metal ductwork inside the dryer cabinet and for venting outside. Failure to follow these

instructions may result in fire or death.

•To reduce the risk of fire, combustion, or

accumulation of combustible gases, DO NOT exhaust dryer air into an enclosed and unventilated area, such as an attic, wall, ceiling, crawl space, chimney, gas vent, or concealed space of a building. Failure to follow these

instructions may result in fire or death.

•To reduce the risk of fire, DO NOT exhaust the dryer with plastic or thin foil ducting. Failure to follow these instructions may result in fire or death.

•The exhaust duct must be 4 inches (10.2 cm)

in diameter with no obstructions. The exhaust duct should be kept as short as possible. Make sure to clean any old ducts before installing your new dryer. Failure to follow these instructions

may result in fire or death.

•Rigid, semi-rigid or flexible metal ducting is

recommended for use between the dryer and the wall. All non-rigid metal transition duct must be UL-listed. Use of other materials for transition duct could affect drying time. Failure

to follow these instructions may result in fire or death.

•DO NOT use sheet metal screws or other

fasteners which extend into the duct that could catch lint and reduce the efficiency of the exhaust system. Secure all joints with duct tape. Failure to follow these instructions may result

in fire or death.

•Do not exceed the recommended duct length

limitations noted in the chart. Failure to follow these instructions may result in extended drying times, fire or death.

•Ductwork is not provided with the dryer. You

should obtain the necessary ductwork locally. The vent hood should have hinged dampers to prevent backdraft when the dryer is not in use.

Failure to follow these instructions may result in fire or death.

•The total length of flexible metal duct must not

exceed 8 ft. (2.4 m).

•In Canada, only those foil-type flexible ducts,

if any, specifically identified for use with the appliance by the manufacturer should be used.

In the United States, only those foil-type flexible ducts, if any, specifically identified for use with the appliance by the manufacturer and that comply with the Outline for Clothes Dryer Transition Duct, Subject 2158A, should be used.

Ductwork

Number

Wall Cap Type

of 90°

Elbows

Recommended

0 65 ft.(19.8 m)

1 55 ft.(16.8 m)

(10.2 cm)

Use only for

short run

installations

2 47 ft.(14.3 m)

3 36 ft.(11.0 m)

4 28 ft.(8.5 m)

0 55 ft.(16.8 m)

1 47 ft.(14.3 m)

2 41 ft.(12.5 m)

21/2"

(6.35 cm)

3 30 ft.(9.1 m)

4 22 ft.(6.7 m)

NOTE

Deduct 6 ft. (1.8 m) for each additional elbow. Do not use more than four 90° elbows.

Maximum length

of 4-inch (10.2 cm)

diameter rigid metal

duct

INSTALLATION

Routing And Connecting Ductwork

NOTE

Follow the guidelines below to maximize drying performance and reduce lint buildup and condensation in the ductwork. Ductwork and fittings are NOT included and must be purchased separately.

•Use 4-inch (10.2 cm) diameter rigid, semi-rigid or flexible metal ductwork.

•The exhaust duct run should be as short as possible.

•Use as few elbow joints as possible.

•The male end of each section of exhaust duct must point away from the dryer.

•Use duct tape on all duct joints.

•Insulate ductwork that runs through unheated areas in order to reduce condensation and lint buildup on duct surfaces.

•Incorrect or inadequate exhaust systems are not covered by the dryer warranty. Dryer failures or service required because of such exhaust systems will not be covered by the dryer warranty.

ENGLISH

Correct Venting

Incorrect Venting

INSTALLATION

Connecting the Inlet Hose (Steam Models)

The dryer must be connected to the cold water tap using a new water supply hose. Do not use old hoses.

NOTE

•Water supply pressure must be between 20 and 120 psi (138—827 kPa) .

•Do not strip or cross-thread when connecting the inlet hose to the valve.

•If the water supply pressure is more than 800 kPa, a pressure-reducing valve should be installed.

•Periodically check the condition of the hose and replace the hose if necessary.

•Replace inlet hoses after 5 years of use to reduce the risk of hose failure.

•Record hose installation or replacement dates on the hoses for future reference.

Check the rubber seal at each end of the inlet

hoses. Two rubber seals are supplied with each inlet hose. They are used for preventing water leaks. Make sure the connection to the cold water tap is tight.

d. Connect the long dryer hose to one side of the

Y-connector and connect the washer hose to the other side.

WITHOUT WASHER: If the dryer does not share the cold water tap with a washer.

a. Connect the straight end of the long hose to the

cold water faucet.

NOTE

•Before connecting the water line to the dryer, flush several gallons of water into a drain or bucket. This will help prevent foreign particles such as sand and scale from clogging the dryer inlet valve.

•Do not overtighten. Damage to the coupling may result.

Connect the hose to the dryer. Connect the

water supply hose to the dryer inlet valve tightly by hand and then tighten another 2/3 turn with pliers. Make sure that there are no kinks in the hoses and that they are not crushed.

Hose

connector

Rubber

seal

Y connector

Check the installation type.

Short hose

Y connector

WITH WASHER WITHOUT WASHER

Connect all water supply hoses tightly by hand and then tighten another 2/3 turn with pliers.

WITH WASHER: When connecting the dryer to the same faucet as a washer.

a. Shut off the cold water tap and remove the washer

hose.

b. Connect the short hose to the Y-connector using

one of the rubber seals.

c. Connect the other end of the short hose to the cold

water faucet.

Long hose

Turn on the cold water faucet.

Check for leaks at the Y-connector (if used) and

in all hoses.

NOTE

•If any leaks are found, shut off the water faucet, remove the hose and check the condition of the rubber seal.

INSTALLATION

Connecting Gas Dryers

WARNING

To reduce the risk of fire or explosion, electric shock, property damage, injury to persons, or death when using this appliance, follow basic safety precautions.

Gas Supply Requirements

•As shipped from the factory, this dryer is

configured for use with propane (LP). It can be converted for use with natural (NG) gas. Gas pressure must not exceed 8 inches (20.3 cm) of water column for NG, or 13 inches (33 cm) of water column for LP.

•A qualified service or gas company technician

must connect the dryer to the gas service. Failure to follow these instructions may result in fire, explosion, or death.

•Isolate the dryer from the gas supply system

by closing its individual manual shutoff valve during any pressure testing of the gas supply.

Failure to do so may result in fire, explosion, or death.

•Supply line requirements: Your laundry room

must have a rigid gas supply line to the dryer. In the United States, an individual manual shutoff valve MUST be installed within at least 6 ft. (1.8 m) of the dryer, in accordance with the National Fuel Gas Code ANSI Z223.1 or Canadian gas installation code CSA B149.1. A 1/8-inch (0.3 cm) NPT pipe plug must be installed. Failure to do so may result in fire,

explosion, or death.

•If using a rigid pipe, the rigid pipe should be

½ inch IPS. If acceptable under local codes and ordinances and when acceptable to your gas supplier, 3/8-inch (1 cm) approved tubing may be used where lengths are less than 20 ft. (6.1 m). Larger tubing should be used for lengths in excess of 20 ft. (6.1 m). Failure to do

so may result in fire, explosion, or death.

•Connect the dryer to the type of gas shown on

the nameplate. Failure to do so may result in fire, explosion, or death.

•To prevent contamination of the gas valve,

purge the gas supply of air and sediment before connecting the gas supply to the dryer. Before tightening the connection between the gas supply and the dryer, purge remaining air until the odor of gas is detected. Failure to do so may

result in fire, explosion, or death.

•DO NOT use an open flame to inspect for gas

leaks. Use a noncorrosive leak detection fluid. Failure to do so may result in fire, explosion, or death.

•Use only a new AGA- or CSA-certified gas

supply line with flexible stainless steel connectors. Failure to do so may result in fire,

explosion, or death.

•Securely tighten all gas connections. Failure to do so may result in fire, explosion, or death.

•Use Teflon tape or a pipe-joint compound

that is insoluble in propane (LP) gas on all pipe threads. Failure to do so may result in fire,

explosion, or death.

•DO NOT attempt any disassembly of the dryer;

disassembly requires the attention and tools of an authorized and qualified service technician or company. Failure to follow this warning may

result in fire, explosion, or death.

Electrical Requirements for Gas Models Only

•Do not, under any circumstances, cut or remove

the third (ground) prong from the power cord.

Failure to follow this warning may result in fire, explosion, or death.

•For personal safety, this dryer must be properly grounded. Failure to follow this warning may result in fire, explosion, or death.

•This dryer must be plugged into a 120 V~60 Hz.

grounded outlet protected by a 15-ampere fuse or circuit breaker.

result in fire, explosion, or death.

•Where a standard 2-prong wall outlet is

encountered, it is your personal responsibility and obligation to have it replaced with a properly grounded 3-prong wall outlet. Failure to

follow this warning may result in fire, explosion, or death.

Failure to follow this warning may

Plug dryer into a 120 V~,

Plug dryer into a

60 Hz grounded 3-prong outlet.

WARNING

ELECTRIC SHOCK HAZARD

Failure to follow safety warnings could result in serious injury or death.

This dryer is equipped with a three-prong grounding plug for protection against shock hazard and should be plugged directly into a properly grounded three-prong receptacle. Do not cut or remove the grounding prong from this plug.

ENGLISH

INSTALLATION

Connecting the Gas Supply

•Installation and service must be performed

by a qualified installer, service agency, or the gas supplier. Failure to do so may result in fire,

explosion, or death.

•Use only a new stainless steel flexible

connector and a new AGA-certified connector. Failure to do so may result in fire, explosion, or death.

•A gas shutoff valve must be installed within 6 ft.

(1.8 m) of the dryer. Failure to do so may result in fire, explosion, or death.

•The dryer is configured for LP gas when

shipped from the factory. Make sure that the dryer is equipped with the correct burner nozzle for the type of gas being used (natural gas or propane gas). Failure to do so may result in fire,

explosion, or death.

•If necessary, the correct nozzle (for the Natural

nozzle kit, order part number 383EEL3002K) should be installed by a qualified technician and the change should be noted on the dryer.

Failure to do so may result in fire, explosion, or death.

•All connections must be in accordance with

local codes and regulations. Failure to do so may result in fire, explosion, or death.

•Gas dryers MUST exhaust to the outdoors. Failure to do so may result in fire, explosion, or death.

Securely tighten all connections between the

dryer and your laundry room’s gas supply.

Turn on your laundry room’s gas supply.

Check all pipe connections (both internal and

external) for gas leaks with a noncorrosive leakdetection fluid.

Proceed to Venting the Dryer.

3/8" → 5/16"

NPT coupling (from dryer to hose – gas tank)

3/8" → 1/2"

NPT coupling (from dryer to pipe –gas pipe)

AGA/CSA-Certied

Stainless Steel Flexible Connector

Gas Supply Shutoff Valve

High-Altitude Installations

The BTU rating of this dryer is AGA-certified for elevations below 10,000 feet.

If your gas dryer is being installed at an elevation above 10,000 feet, it must be derated by a qualified technician or gas supplier.

NOTE

This dryer is configured from the factory for propane (LP). If the dryer is to be used with natural gas (NG) gas, it must be converted by a qualified service technician.

Make sure that the gas supply to the laundry

room is turned OFF and the dryer is unplugged. Confirm that the type of gas available in your laundry room is appropriate for the dryer.

Remove the shipping cap from the gas fitting at

the back of the dryer. Be careful not to damage the threads of the gas connector when removing the shipping cap.

Connect the dryer to your laundry room’s gas

supply using a new flexible stainless steel connector with a 3/8-inch NPT fitting.

NOTE

DO NOT use old connectors.

INSTALLATION

Connecting Electric Dryers

Electrical Requirements for Electric Models Only

WARNING

To help prevent fire, electric shock, serious injury, or death, the wiring and grounding must conform to the latest edition of the National Electrical Code, ANSI/NFPA 70 and all applicable local regulations. Please contact a qualified electrician to check your home’s wiring and fuses to ensure that your home has adequate electrical power to operate the dryer.

•This dryer must be connected to a grounded

metal, permanent wiring system, or an equipment-grounding conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead on the dryer. Failure to do so may result in fire,

explosion, or death.

•The dryer has its own terminal block that must

be connected to a separate 240 V~, 60 Hertz, single-phase circuit, fused at 30 amperes (the circuit must be fused on both sides of the line). ELECTRICAL SERVICE FOR THE DRYER SHOULD BE OF THE MAXIMUM RATE VOLTAGE LISTED ON THE NAMEPLATE. DO NOT CONNECT THE DRYER TO 110-, 115-, OR 120VOLT CIRCUIT. Failure to follow these instructions

may result in fire, explosion, or death.

•If the branch circuit to dryer is 15 ft. (4.5 m)

or less in length, use UL (Underwriters Laboratories) listed No. 10 AWG wire (copper wire only), or as required by local codes. If over 15 ft. (4.5 m), use UL-listed No. 8 AWG wire (copper wire only), or as required by local codes. Allow sufficient slack in wiring so the dryer can be moved from its normal location when necessary. Failure to do so may result in

fire, explosion, or death.

•The power cord (pigtail) connection between

the wall receptacle and the dryer terminal block IS NOT supplied with the dryer. Type of pigtail and gauge of wire must conform to local codes and with instructions on the following pages.

Failure to follow these instructions may result in fire, explosion, or death.

•A 4-wire connection is required for all mobile

and manufactured home installations, as well as all new construction after January 1, 1996. A 4-wire connection must be used where local codes do not permit grounding through the neutral wire. Failure to do so may result in fire,

explosion, or death.

•Do not modify the plug and internal wire provided with the dryer.

•The dryer should be connected to a 4-hole outlet.

•If the plug does not fit the outlet, a proper outlet will need to be installed by a qualified electrician.

Special Electrical Requirements for Mobile or Manufactured Homes

•Any installation in a manufactured or mobile home must comply with the Manufactured Home Construction and Safety Standards Title 24 CFR, Part 3280 or Standard CAN/ CSA Z240 MH and local codes and ordinances. If you are uncertain whether your proposed installation will comply with these standards, please contact a service and installation professional for assistance.

•A 4-wire connection is required for all mobile

and manufactured home installations, as well as all new construction after January 1, 1996.

Failure to do so may result in fire, explosion, or death.

•A gas dryer must be permanently attached to the floor.

•The electrical connection for an electric dryer must be a 4-wire connection. More detailed information concerning the electrical connection is provided in the Connecting Electric Dryers section.

•To reduce the risk of combustion and fire, the dryer must be vented to the outside.

•DO NOT vent the dryer under a manufactured home or mobile home.

•Electric dryers may be vented to the outside using the back, left, right, or bottom panel.

•Gas dryers may be vented to the outside using the back, left, or bottom panel. Gas dryers may not be vented to the outside using the right side panel because of the burner housing.

•The dryer exhaust duct must be affixed securely to the manufactured or mobile home structure, and the exhaust duct must be made of a material that will resist fire and combustion. It is recommended that you use a rigid, semi-rigid or flexible metal duct.

•DO NOT connect the dryer exhaust duct to any other duct, vent, chimney, or other exhaust duct.

•Make sure the dryer has adequate access to outside fresh air to ensure proper operation. The opening for outside fresh air must be at least 25 sq. in (163 cm

•It is important that the clearance of the duct from any combustible construction be at least 2 inches (5 cm), and when venting the dryer to the outdoors, the dryer should be installed with a clearance of at least 1 inch (2.5 cm) at the sides and back of the dryer.

•Venting materials are not supplied with the dryer. You must obtain the venting materials necessary for proper installation.

ENGLISH

INSTALLATION

WARNING

Connect the power cord to the terminal block. Connect each wire in the power cord to the terminal block screw with the matching colored wire. The terminal block wire colors are indicated in the manual. Failure to follow these instructions may result in a short or overload.

Grounding through the neutral conductor is prohibited for: (1) new branch-circuit installations, (2) mobile homes, (3) recreational vehicles, and (4) areas where local codes prohibit grounding through the neutral conductor.

Four-Wire Power Cord

•A 4-wire connection is required for all mobile and manufactured home installations, as well as all new construction after January 1, 1996.

•A UL-listed strain relief is required.

•Use a 30-amp, 240-volt, 4-wire, UL-listed power cord with #10 AWG-minimum copper conductor and closed loop or forked terminals with upturned ends.

Attach the two hot leads of the power cord to the

outer terminal block screws.

Attach the white neutral wire to the center screw

of the terminal block.

Attach the power cord ground wire to the green

ground screw.

Tighten all screws securely.

Reinstall the terminal block access cover.

Hot (Black)

Ground Screw

Power Cord Ground Wire

Neutral (White)

Hot (Red)

White Wire moved from Ground Screw

Remove the terminal block access cover on the

upper back of the dryer.

Install a UL-listed strain relief into the power cord

through-hole.

Thread a 30 A / 240 V~, 4-wire, UL-listed power

cord with #10 AWG-minimum copper conductor through the strain relief.

Terminal Block

UL-Listed Strain Relief

UL-Listed 4-Wire Power Cord

Transfer the dryer’s ground wire from behind the

green ground screw to the center screw of the terminal block.

NOTE

This dryer is supplied with the neutral wire grounded. This white ground wire MUST BE MOVED to the neutral terminal when a 4-wire cord is to be used, or where grounding through the neutral conductor is prohibited.

INSTALLATION

Four-Wire Direct Wire

•A 4-wire connection is required for all mobile and manufactured home installations, as well as all new construction after January 1, 1996.

•A UL-listed strain relief is required.

•Use UL-listed 4-wire #10 AWG-minimum copper conductor cable. Allow at least 5 ft. (1.5 m) of wire to allow for removal and reinstallation of the dryer.

Remove 5 inches (12.7 cm) of the outer covering

from the wire. Remove 5 inches (12.7 cm) of insulation from the ground wire. Cut off approximately 1½ inches (3.8 cm) from the other three wires and strip 1 inch (2.5 cm) of insulation from each wire. Bend the ends of the three shorter wires into a hook shape.

1" (2.5 cm)

Ground Wire

(12.7 cm)

Remove the terminal block access cover on the

upper back of the dryer.

Attach the two hot leads of the power cord to the

outer terminal block screws.

Attach the white neutral wire to the center screw

of the terminal block.

Attach the power cord ground wire to the green

ground screw.

Tighten all screws securely.

Reinstall the terminal block access cover.

Hot (Black)

Ground Screw

Power Cord Ground Wire

Neutral (White)

ENGLISH

Hot (Red)

White Wire moved from Ground Screw

Install a UL-listed strain relief into the power cord

through-hole.

Thread the 4-wire #10 AWG-minimum copper

power cable prepared in step 1 through the strain relief.

Terminal Block

UL-Listed Strain Relief

UL-Listed 4-Wire Power Cord

Transfer the dryer’s ground wire from behind the

green ground screw to the center screw of the terminal block.

NOTE

INSTALLATION

WARNING

Three-Wire Power Cord

•A 3-wire connection is NOT permitted on new construction after January 1,

1996.

•A UL-listed strain relief is required.

•Use a 30A / 240V~, 3-wire, UL-listed power cord with #10 AWG-minimum copper conductor and closed loop or forked terminals with upturned ends.

Remove the terminal block access cover on the

upper back of the dryer.

Install a UL-listed strain relief into the power cord

through-hole.

Attach the neutral (white) wire to the center

terminal block screw.

NOTE

The dryer is supplied with the neutral conductor grounded. If a 3-wire cord is to be used and is allowed, make sure the white neutral grounding wire is connected to the green ground screw.

Connect the external ground (if required by local

codes) to the green ground screw.

Tighten all screws securely.

Reinstall the terminal block access cover.

Neutral (White)

Ground Screw

White Wire from Dryer harness

Hot (Black)

External Ground Wire (If required by local codes)

Hot (Red)

Thread a 30A / 240V~, 3-wire, UL-listed power

cord with #10 AWG-minimum copper conductor through the strain relief.

Terminal Block

UL-Listed Strain Relief

UL-Listed 3-Wire Power Cord

Attach the two hot leads (black and red) of the

power cord to the outer terminal block screws.

INSTALLATION

Three-Wire Direct Wire

•A 3-wire connection is NOT permitted on new construction after January 1,

1996.

•A UL-listed strain relief is required.

•Use UL-listed 3-wire, #10 AWG-minimum copper conductor cable. Allow at least 5 ft. (1.5 m) length to allow for removal and installation of dryer.

Remove 3½-inch (8.9 cm) of the outer covering

from the wire. Strip 1 inch (2.5 cm) insulation from each wire. Bend the ends of the three wires into a hook shape.

1" (2.5 cm)

Remove the terminal block access cover on the

upper back of the dryer.

Install a UL-listed strain relief into the power cord

through-hole.

Thread the 3-wire, #10 AWG-minimum copper

conductor power cable prepared in step 1 through the strain relief.

Terminal Block

UL-Listed Strain Relief

Reinstall the terminal block access cover.

Ground Screw

White Wire from Dryer harness

Hot (Black)

External Ground Wire (If required by local codes)

Neutral (White)

Hot (Red)

Final Installation Check

Once you have completed the installation of the dryer and it is in its final location, confirm proper operation with the following tests and the Installation Test (Duct Check) on the following page.

Testing Dryer Heating

GAS MODELS Close the dryer door, press the Encendido/Apagado

(Power) button to turn the dryer on, and start the

dryer on a heat setting. When the dryer starts, the igniter should ignite the main burner.

ELECTRIC MODELS Close the dryer door, press the Encendido/Apagado

(Power) button to turn the dryer on, and start the

dryer on a heat setting. The exhaust air should be warm after the dryer has been operating for 3 minutes.

ENGLISH

UL-Listed 3-Wire Power Cord

Attach the two hot leads (black and red) of the

power cord to the outer terminal block screws.

Attach the neutral (white) wire to the center

terminal block screw.

NOTE

The dryer is supplied with the neutral conductor grounded. If a 3-wire cord is to be used and is allowed, make sure the white neutral grounding wire is connected to the green ground screw.

Connect the external ground (if required by local

codes) to the green ground screw.

Tighten all screws securely.

Checking Airow

Effective dryer operation requires proper airflow. The adequacy of the airflow can be measured by evaluating the static pressure. Static pressure in the exhaust duct can be measured with a manometer, placed on the exhaust duct approximately 2 ft. (60.9 cm) from the dryer. Static pressure in the exhaust duct should not exceed 0.6-inch (1.5 cm). The dryer should be checked while the dryer is running with no load.

Checking Levelness

Once the dryer is in its final location, recheck the dryer to be sure it is level. Make sure it is level front to back and side to side, and that all four leveling feet are firmly on the floor.

Checking Venting

Vent ductwork should be checked for lint buildup and cleaned at least once per year. If any noticeable reduction in drying performance occurs, check duct for obstructions and blockages.

INSTALLATION

Installation Test (Duct Check)

Once you have completed the installation of the dryer, use this test to make sure the condition of the exhaust system is adequate for proper operation of the dryer. This test should be performed to alert you to any serious problems in the exhaust system of your home.

•This dryer features Flow Sense™, an innovative sensing system that automatically detects blockages and restrictions in dryer ductwork. Keeping ductwork clean of lint buildup and free of restrictions allows clothes to dry faster and reduces energy use.

NOTE

The dryer should be cool before starting this test. If the dryer was warmed up during installation, run the Secado Con Aire(Air Dry) cycle for a few minutes to reduce the interior temperature.

To activate the installation test:

Remove the drying rack and literature, and

then close the door.

Do not load anything in the drum for this test, as in may affect the accuracy of the results.

Check the display for results.

During the test cycle, monitor the Flow Sense™ display on the control panel. If the Flow Sense™ LED has not turned on, when the cycle ends, the exhaust system is adequate. If the exhaust system is severely restricted, the Flow Sense™ LED will turn on. Other problems may also be shown with error codes. See the chart on the next page for error code details and solutions.

LED turned on:

RESTRICTED

The Flow Sense™ LED indicates that the exhaust system is severely restricted. Have the system checked immediately, as performance will be poor.

End of cycle.

At the end of the test cycle, The test cycle will end and the dryer will shut off automatically after a short delay.

will display.

Press and hold the Señal(Signal) and Temp.

buttons and then press the Encendido/ Apagado (Power) button.

(On models with a glass touch control panel, press the Encendido/Apagado (Power) button then IMMEDIATELY press and hold the Temp. and Señal(Signal) buttons.) This button sequence activates the installation test. The code is successful.

Press the Inicio/Pausa(Start/Pause) button.

The dryer will start the test, which will last about 2 minutes. The heat will be turned on and the temperatures in the drum will be measured and displayed. A chime sounds when the test portion of the cycle is complete.

will display if the activation

•Check the error code before you call for service

Error Code

tE1

tE2

PS or PF or nP

gAS

Possible

Causes

•Temperature sensor failure.

•Humidity sensor failure.

•Electric dryer power cord is not connected correctly, or house power supply is incorrect.

•House fuse is blown, circuit breaker has tripped, or power outage has occurred.

•Gas supply or service turned off. (Gas Model only.)

Solutions

•Turn off the dryer and call for service.

•Check the power supply or the connection of the power cord to the terminal block. Refer to the Connecting Electric Dryers section of this manual for complete instructions.

•Reset circuit breaker or replace fuse. Do not increase the fuse capacity. If the problem is a circuit overload, have it corrected by a qualified electrician.

•Confirm that house gas shutoff and the dryer gas shutoff are both fully open.

INSTALLATION

•Check the duct condition If the Flow SenseTM LED is turned on, check the exhaust system for restrictions and damage. Repair or replace the exhaust system as needed.

NOTE

When the dryer is rst installed, this test should

be performed to alert you to any existing problems with the exhaust duct in your home. However, since the test performed during normal operation provides more accurate information on the condition of the exhaust duct than does the installation test, the number of bars displayed during the two tests may not be the same.

Do not interrupt the test cycle, as this could result in inaccurate results.

Even if no bars are displayed during the test cycle, some restrictions may still be present in the exhaust system. Refer to the Venting the Dryer section of this manual for complete exhaust system and venting requirements.

Your dryer features Flow Sense™, an innovative sensing system that automatically detects blockages and restrictions in the dryer ductwork. Keeping ductwork clean of lint buildup and free of restrictions allows clothes to dry faster and reduces energy use.

Restricted or Blocked Airow

Avoid long runs or runs with multiple elbows or bends.

Excess or crushed

transition duct

Check for blockages and lint buildup.

Make sure the ductwork is not crushed or restricted.

Too many elbows or

exhaust too long

Lint buildup or blockage

ENGLISH

Crushed

damaged

exhaust

Lint Filter

OPERATION

WARNING

To reduce the risk of fire, electric shock, or injury to persons, read this entire manual, including the IMPORTANT SAFETY INSTRUCTIONS, before operating this dryer.

Using the Dryer

1 Clean the Lint Filter

If the lint filter has not already been cleaned, lift out the filter and remove the lint from the last load. This will help ensure the fastest and most efficient drying performance. Make sure to reinstall the filter, pressing down until it clicks firmly into place. The dryer will not operate without the lint filter in place.

2 Load the Dryer

Load the dryer with the wet laundry from the washer. If the load is extra large, you may need to divide it into smaller loads for proper performance and fabric care.

3 Turn on The Dryer

Press the Encendido/Apagado (Power) button to turn on the dryer. The cycle LEDs will illuminate and a chime will sound.

4 Select a Cycle

Turn the cycle selector knob in either direction until the LED for the desired cycle is on. The preset temperature, dry level, and option settings for that cycle will be shown. Default settings for the selected cycle can now be changed if desired. Refer to the Cycle Setting and Options page for details.

NOTE

Not all options or modifiers are available on all cycles. A different chime will sound and the LED will not come on if the selection is not allowed.

5 Begin the Cycle

Press the Inicio/Pausa(Start/Pause) button to begin the cycle. The cycle can be paused at any time either by opening the door or by pressing the Inicio/ Pausa(Start/Pause) button. If the cycle is not restarted within 60 minutes of being paused, the dryer will shut off and the settings will be lost.

6 End of Cycle

When the cycle is finished, the chime will sound. Immediately remove your clothing from the dryer to reduce wrinkling. If Anti Arrugas(Wrinkle Care) is selected, the dryer will tumble briefly every few minutes to help prevent wrinkles from setting in the clothes.

+ 86 hidden pages