LG D1451LF Owner’s Manual

OWNER’S MANUAL

WASHING MACHINE

WM0642H*

P/NO : MFL31245123

www.lg.com

Please read this manual carefully before operating your set and retain it for future reference.

DISHWASHER

OWNER'S MANUAL

Before beginning installation, read these instructions carefully. This will simplify installation and ensure that the dishwasher is installed correctly and safely. Leave these instructions near the dishwasher after installation for future reference.

D1451W(L,M,T,B,C,D,A,S)F(B,U) D1452W(L,M,T,B,C,D,A,S)F(B,U) D1462W(L,M,T,B,C,D,A,S)F(B,U) D1417WFB

P/No. : MFL66281485

1. MFL66281485_EN_131210.indd 1 2013.12.10 8:58:10 AM

For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, injury to persons, or death.

READ ALL INSTRUCTIONS AND EXPLANATION OF THE INSTALLATION BEFORE USE

WARNING

You can be killed or seriously injured if you don’t follow instructions.

Your Safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word DANGER, WARNING or CAUTION.

These words mean:

WARNING

You may be slightly injured or cause damage to the product,if you do not follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

CAUTION

You will be killed or seriously injured if you don’t immediately follow instructions.

DANGER

CONTENTS ................................

IMPORTANT SAFETY

INSTRUCTIONS

Important safety instructions ..............3

Read all instructions before use ........4

Save these instructions ...................... 5

INSTALLATION INSTRUCTIONS

Prepare cupboard opening ................ 7

Preparation for electrical wiring ........7

Preparing the dishwasher for

installation ..........................................8

Installing the dishwasher in

cupboard .......................................8

Installation of drain hose ....................9

Installation of water inlet hose .........10

Final check and assembling ............10

How to level the dishwasher ............ 10

PARTS NAME ..........................

FUNCTION OF CONTROL

BUTTON ...................................

BEFORE USING FOR THE

FIRST TIME

Check and find water hardness

level ...........................................15

Setting up the softening system

level of your dishwasher .................. 15

Salt Filling ........................................ 16

Adding Rinse Aid ............................. 16

INFORMATION FOR ENERGY

TEST ........................................

HOW TO USE AND OPERATE

Daily use load .................................. 18

Cutlery Basket .................................19

Lower Rack ......................................20

Upper Rack ......................................20

Adding Detergent .............................22

Relling ............................................ 23

Drying ..............................................24

OPERATING SEQUENCE ......

PROGRAMME .........................

USER MAINTENANCE

INSTRUCTIONS

Keeping the dishwasher ..................27

Filters ............................................... 27

Lower Spray Arm ............................. 27

Upper Spray Arm ............................. 27

Water Inlet........................................27

TROUBLE SHOOTING GUIDE

Before calling for service .................28

Using SMARTDIAGNOSIS™ ..........31

SPECIFICATION .....................

CONTENTS

Thank you for buying a LG Dishwasher.

Please read your owner’s manual carefully, it provides instruction on safe installation, use and maintenance. Retain it for future reference.

Record the model and serial number of your Dishwasher.

Model No.

Serial No.

Date of Purchase

1. MFL66281485_EN_131210.indd 2 2013.12.10 8:58:10 AM

For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, injury to persons, or death.

READ ALL INSTRUCTIONS AND EXPLANATION OF THE INSTALLATION BEFORE USE

WARNING

You can be killed or seriously injured if you don’t follow instructions.

Your Safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word DANGER, WARNING or CAUTION.

These words mean:

WARNING

You may be slightly injured or cause damage to the product,if you do not follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

CAUTION

You will be killed or seriously injured if you don’t immediately follow instructions.

DANGER

IMPORTANT SAFETY INSTRUCTIONS

1. MFL66281485_EN_131210.indd 3 2013.12.10 8:58:10 AM

• Please read this manual carefully before using the dishwasher for the first time.

• This manual contains very important notes

regarding the installation, use and maintenance of your dishwasher.

• The manufacturer can not be responsible

for problems caused by ignoring these safety and caution instructions.

• This dishwasher is designed for normal

household use.

• Do not use the dishwasher for industrial and commercial use, or other purpose.

• The appliance is not intended for use by young children or infirm persons without supervision.

• Check packaging and dishwasher immediately for signs of transport damage. If the appliance is damaged, do not put it into use but contact your supplier without delay.

• This appliance is intended to be used in

household and similar applications such as;

- Staff kitchen areas in shops, offices and other working environments;

- Farm houses;

- By clients in hotels, motels and other residential type environments;

- Bed and breakfast type environments.

• If this product is used for commercial

purpose, it is not warranted. (Example: Public places such as restaurant, lodging house, training center, dormitory) If the product is installed outside the normal service area, any cost of transportation involved in the repair of the product, or the replacement of a defective part, shall be borne by the owner.

IMPORTANT SAFETY INSTRUCTIONS

Read all instructions before use

WARNING

To reduce the risk of fire, electric shock, or injury to persons when using the dishwasher, follow basic precautions, including the following:

• Electrical connection must be in accordance with the rating label.

• Electrical safety is only guaranteed when

the earth system of your house is in accordance with the related local regulations. (Do not use an extension

cable or cord.)

• If the hot water exceeds 65ºC, adjust the

water heater setting. If the hot water temperature can not be maintained below

65ºC, the dishwasher must be connected

to cold water.

• If power supply cord is damaged, it must

only be replaced by the manufacturer or its service agent or a similar qualified person in order to avoid a hazard.

• This appliance must be positioned so that

the plug is accessible.

• The appliance is to be connected to the

water mains using new hose-sets and that old hose-sets should not be reused.

During installation

• Only suitable household utensils should be placed in the dishwasher.

(Please avoid utensils; that are nonheat-resistant, metal decorated, etc.)

During use

1. MFL66281485_EN_131210.indd 4 2013.12.10 8:58:11 AM

IMPORTANT SAFETY INSTRUCTIONS

Read all instructions before use

WARNING

To reduce the risk of fire, electric shock, or injury to persons when using the dishwasher, follow basic precautions, including the following:

• Do not use any kinds of solvent in your dishwasher. They may cause an explosion or fire.

• Do not spray water on the appliance. It may cause the failure of electric parts or electric shock.

• Do not push down or sit on the inner door when the door is opened. It may cause the deformation or failure of your dishwasher.

• Do not use the detergent for hand washing. The detergent for dishwasher should be used for normal operation.

• This appliance is fitted with a safety

function that automatically stops the operation of the dishwasher when it is exposed to heavy disturbance on its mains.

• Dishwasher detergents are strongly

alkaline.They can be extremely dangerous if swallowed.

Avoid contact with skin and eyes and keep children away from the dishwasher when the door is open.

Check that the detergent receptacle is empty after completion of the wash cycle.

• Controls may be locked using Child Lock

mode to prevent all the settings from being changed by a child.

• Keep children away from detergents and rinse-aids.

• Do not allow children to operate the dishwasher.

• Young children should be supervised to ensure that they do not play with the appliance.

Child Safety

GROUNDING INSTRUCTIONS

This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current.

This appliance is equipped with a cord having an equipment-grounding conductor and grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinance.

• Do not use an adapter this will defeat the grounding plug.

• If you don’t have the proper outlet, consult an electrician.

Save these instructions

All batteries (whether installed or attached) should not be exposed to excess heat like

sunlight or similar source.

1. MFL66281485_EN_131210.indd 5 2013.12.10 8:58:11 AM

IMPORTANT SAFETY INSTRUCTIONS

CAUTION

The instructions shall state the substance of the following :

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they

have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.

Disposal of your old appliance

1. When this crossed-out wheeled bin symbol is attached to a product it means the product is covered by the European Directive 2002/96/EC.

2. All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities.

3. The correct disposal of your old appliance will help prevent potential negative consequences for the environment and human health.

4. For more detailed information about disposal of your old appliance, please contact your city office, waste disposal service or the shop where you purchased the product.

CAUTION

CAUTION concerning the Power cord

• Most appliances recommend they be placed upon a dedicated circuit; that is, a single

outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the specification page of this owner's manual to be certain.

• Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets,

extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in an electric shock or fire.

• Periodically examine the cord of your appliance, and if its appearance indicates

damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer.

• Protect the power cord from physical or mechanical abuse, such as being twisted,

kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance. If the appliance is supplied from a cord extension set or an electrical portable outlet device, the cord extension set on electrical portable outlet device must be positioned so that it is not subject to splashing or ingress of moisture.

WARNING

Improper connection of the equipment-grounding conductor can result in electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the appliance is properly grounded. Do not modify the plug provided with the appliance - if it does not fit the outlet, have a proper outlet installed by a qualified electrician.

1. MFL66281485_EN_131210.indd 6 2013.12.10 8:58:11 AM

A qualified electrician/plumber or competent person should carry out any electrical/

• plumbing work required to install this appliance.

WARNING

1. This appliance must be supplied with correct rating voltage and hertz as shown on instruction manual, and connected to an individual, properly earthed branch circuit, protected by a minimum 15 amp circuit breaker or time delay fuse. Wiring must be 2 wires with Earth.

2. The power plug must be in a accessible location adjacent to and not behind the dishwasher and within 1.2 meters of the dishwasher side.(See page 9 Fig.A)

3. The power plug must be correctly earthed, if in doubt, have it checked by a qualified Electrician. No other appliance should be connected to the same plug outlet by a double adapter or similar plug.

Dangerous voltage

To indicate hazards arising from dangerous voltages.

Note- in case of an application warning sign, the rules according to ISO 3864 should be adhered to.

1. This dishwasher is designed to fit the size shown as below.

2. Select a location as close to sink as possible for ease of connection to the water and drain pipes.

3. To ensure good drainage, the dishwasher should not be installed more than 3 meters away from the sink.

4. If dishwasher is installed in a corner, a minimum of 5cm of space is required between the washer and an adjacent cabinet or wall.

Unit:mm

INSTALLATION INSTRUCTIONS

For personal safety, remove house

• fuse or open circuit breaker before

installation. Do not use an extension cord or

• adapter plug with this appliance.

Electrical and earthing connections must comply with the national electrical code/ provincial and municipal code and/or other local codes.

CAUTION

Any bare wood surrounding the

• dishwasher should be sealed with a

waterproof paint or sealant to prevent swelling.

CAUTION

Prepare cupboard opening

Preparation for electrical wiring

1. MFL66281485_EN_131210.indd 7 2013.12.10 8:58:12 AM

If the height of the cupboard is below

• 850mm, you should remove the top table

by unscrewing the 2 screws. (Two from rear)

CAUTION

1. Lay the dishwasher on its back.

2. Adjust the legs to the required height as shown in below figure.

1. Before sliding the dishwasher into the cupboard opening, all necessary height and balancing adjustments should be made using a spanner.

2. Slide the dishwasher into the cabinet, opening carefully. Make sure that the drain hose inside the cabinet is not kinked or stretched.

Adjust

leg

INSTALLATION INSTRUCTIONS

Preparing the dishwasher for

installation

Installing the dishwasher in

cupboard

1. MFL66281485_EN_131210.indd 8 2013.12.10 8:58:13 AM

1. If the end of drain hose does not fit to the drain line, use a rubber connector(not supplied) that is resistant to heat and detergent.

2. This should be available from a plumbing shop or DIY merchants.

3. There are two typical connections as shown in Figure A, B.

The S trap spigot must be drilled out cleanly and free of obstruction to its maximum internal diameter, if used for drainage.

To prevent siphoning, one of the following methods must be used:

When the drain hose is connected to a sink

S trap or waste disposal unit, the hose must be looped up to the underside of the bench top and secured.

Drain hose Extension

Extend drain hose as shown below.

Fig. A

When the drain hose is connected to a

separate standpipe, it is essential that an airtight connection be made. Refer to Fig.B

Fig. B : Drainage connection - stand pipe.

INSTALLATION INSTRUCTIONS

Installation of drain hose

When you connect or extend drain hose,

•

make sure that drain hose is not kinked.

(Bends should have a 40 mm radius.)

CAUTION

1. MFL66281485_EN_131210.indd 9 2013.12.10 8:58:14 AM

• This dishwasher may be fed with either hot or

cold water. If the water can not be maintained below 65ºC, the dishwasher must be connected to cold water.

• When connecting, you may use sealant tape or

sealing compound to avoid water leaks.

• Make sure that the line is not kinked or sharply

bent.

• It is recommended that the new inlet hose be

used and not the existing or old hose.

Final check and assembling

1. Securely hand tighten supply hose to the water supply. Plug the power supply cord into an earthed electrical point and switch on.

2. After installing and prior to using the

dishwasher with crockery, we recommend that you use the dishwasher on Quick mode to rinse through. At this stage it is useful to ensure that there are no operating problems or water leaks. When the dishwasher is used for the first time, there may be a loud noise, if this happens, turn off the power and restart the dishwasher.

After installing the dishwasher, you may notice a slight sticking of the door to the dishwasher, when you open or close the door. If this does happen you need to adjust the level of the dishwasher.

• If the door slants to the right, see fig. C and

follow these instructions:

1) Unscrew(counter-clockwise) the left leg of the back side and correct the level.

2) Check the opening of door and repeat if necessary until the door opens and closes properly.

• When the product is correctly leveled, there

should be no slant, stickiness or friction sound.

Fig. C

Case 1. In case the door is slanted to the right

• If the door slants to the left, see fig. D and

follow these instructions:

1) Check the opening of door if there still remains sticky or friction sound.

2) Check the opening of door and repeat if necessary until the door opens and closes properly.

• When the product is correctly leveled, there

should be no slant, stickiness or friction sound.

Fig. D

Case 2. In case the door is slanted to the left

Water supply hose

Water tap

Fig. A

Fig. B

Connect the water supply hose to the water tap.

(Fig. A)

Some models consist of an inlet valve and hose.

(Fig. B) After connecting the inlet hose to the tap, turn on the tap to flush out foreign substances (dirt, sand or sawdust) in the water lines. Let water drain into a bucket, and check the water temperature. Connect the supply hose to the water inlet valve.

INSTALLATION INSTRUCTIONS

Installation of water inlet hose How to level the dishwasher

1. MFL66281485_EN_131210.indd 10 2013.12.10 8:58:15 AM

PARTS NAME

1. Control Panel

2. Door Handle

3. Front Cover

4. Lower Cover

5. Display Window

6. Power Button

7. Drain Hose

8. Inlet Hose

9. Power Cord

10. Adjustable Leg

11. Upper Rack

12. Cutlery Basket

13. Detergent And Rinse Aid Dispenser

14. Vapor Vent Cover

15. Upper Spray Arm

16. Lower Spray Arm

17. Filter ASM

18. Lower Rack

19. Salt Container Cap

※ The appearance and specifications may vary without notice.

Funnel

Accessory

1. MFL66281485_EN_131210.indd 11 2013.12.10 8:58:17 AM

FUNCTION OF CONTROL BUTTON

■

MODEL :

D1451W(L,M,T,B,C,D,A,S)F(B,U) D1452W(L,M,T,B,C,D,A,S)F(B,U) D1417WFB

■

MODEL : D1462W(L,M,T,B,C,D,A,S)F(B,U)

①

1. MFL66281485_EN_131210.indd 12 2013.12.10 8:58:19 AM

⑫

SMARTDIAGNOSIS

™

function is available only for

the products with a

SMARTDIAGNOSIS

™

mark.

(Refer to Page 31.)

④ ⑥⑤ ⑨

⑦

⑩⑧ ⑪

②

③

④ ⑥⑤ ⑨

⑦

⑩⑧ ⑪

②

③

1. MFL66281485_EN_131210.indd 13 2013.12.10 8:58:20 AM

FUNCTION OF CONTROL BUTTON

①

Process Indicator

• Indicates current program phase.

• The Wash, Rinse and Dry lamps twinkle while each phase of washing process.

• The Clean lamp turns on after all procedure is ended for 4minutes.

②

Salt & Rinse Refill Indicator

• Salt : Refill with special salt when the lamp turns on.

• Rinse : Refill with rinse aid when the lamp turns on.

③

Half Load

• In case of small load, use upper or lower rack only to save energy.

• With each press, can select Upper or Lower rack only.

• In case you don’t select this button, the machine always works vario washing, which operate upper and lower spray

arm alternately.

• In case you select the Dual Spray, the level of water jet is changed to soft or strong in a sequence.

(The level of water jet is strong when the lamp turns on.)

④

Extra Hot & Child Lock Indicator

• Lamp will turn on when the Extra Hot setting is on.

• Lamp will turn on when the Child Lock setting is on.

⑤

Time Left

• Before starting, the display window shows the running time of the selected program.

•  After starting, the display window shows the remaining time.

• If the dishwasher has a trouble, the trouble type is displayed. (OE, IE, EI, FE, HE, tE, LE)

• If these error letters are displayed, please refer to the trouble shooting guide page 29 and follow the guide.

⑥

Delay Start

• If you want to delay the start of selected program, press this button.

•  Pressing this button will increase time by 1 hour.

• The delay start time can be adjusted from 1 hour to 19 hours.

⑦

Program

• Press the cycle that corresponds to your desired wash cycle.

⑧

Extra Hot

• If you select the Extra Hot function, the operating temperature will be up to 80ºC.

(Dual Spray, Auto, Eco, Care)

⑨

Beep On/Off

• The dishwasher must be switched on.

• The beep on/off function can be set by pressing the Delay Start and Care buttons simultaneously for a few seconds.

• On/OFF(FF) is displayed.

⑩

Child Lock

• Used to lock or unlock the control buttons to prevent all the setting from being changed by a child.

• To activate or release the Child Lock function, press the Care and Quick buttons simultaneously for a few seconds

while the dishwasher is in operation.

• All controls will be disabled except the Child Lock and Power buttons.

• Turning off the dishwasher will not reset the Child Lock function. You must release the Child Lock before you can

operate the dishwasher.

⑪

Power

• For operating, press this button first for power on.

• After operating, this button automatically switches off for safety and energy saving.

• In case of irregular surge disturbance to the machine, the power may be automatically turned off for safety.

⑫ UV

(※ D1462 only)

• If you want to sterilize the dishes, press Dual Spray and Auto button.

• After drying cycle, sterilizer will be performed by UV lamp.

• At this time, St code is displayed in display window.

• When you open the door of dishwasher, UV lamp is turned off.

※ Don’t look at the lamp directly with the naked eye.

1. MFL66281485_EN_131210.indd 14 2013.12.10 8:58:21 AM

■

Method 1

1) Check the water hardness in your area. (Your water utility company can help you with this.)

2) Set the softening system level of your dishwasher according to the water hardness level. Refer to Step 2.

■

Method 2

1) Check your water hardness by using test strip. (

)

2) Test Procedure ① Immerse all reaction zones of the test strip for approx.1sec (not in running water!). ② Shake off excess liquid from the strip and wait for 1min.

Then, the green colour of the reaction zone will change to the red-violet.

③ Count the number of red-violet from the strip.

Adjust the water softener to the setting corresponding to the water hardness level in your area. The water softener has 8 adjustment levels. The dishwasher is programmed at the factory for a water hardness level of

This can be checked and altered by using the buttons on the control panel.

1. First, ensure the dishwasher is switched off.

2. Press Half Load and Power button simultaneously and keep them pressed.

3. To change the setting: Simply press the Half Load button, then the figure will change one by one. The display will change between

and .

4. Once the hardness setting is correctly adjusted, press the Delay Start button.

The hardness setting is then saved.

Step 2. Setting up the softening system level of your dishwasher

Step 1. Check and find water hardness level

※ You have to check your water hardness and set the softening system level before

operating your dishwasher.

3) Set the softening system level of your dishwasher according to the water hardness level. Refer to Step 2.

< Water hardness level >

1 °e = 14.25 mg/l CaCO 1 °f = 10 mg/l CaCO 1 °d = 10 mg/l CaO (=1,78 °f) (=1,25 °e)

Hardness range

Number of

the areas

(red-violet)

e°f

mmol/l

(Ca+Mg)

mg/l

Water

quality

Softening

system

level

7 - 14

14 - 21

>21

9 - 17,5

17,5 - 26

>26

<12,5

12,5 - 25

25 - 37

>37

<1,3 1,3 - 2,5 2,5 - 3,8

>3,8

<50

50 - 100

100 - 150

>150

soft

moderately hard

hard

very hard

H0, H1 H2, H3 H4, H5 H6, H7

1 2 3 4

Hardness setting

< Water hardness level >

(*L : Softening system level)

BEFORE USING FOR THE FIRST TIME

1. MFL66281485_EN_131210.indd 15 2013.12.10 8:58:22 AM

Step 4. Adding Rinse Aid

■ 

For filling

Step 3. Salt Filling

Fill the regenerating salt container before starting the washing programme. Once you have filled with salt you must run the Quick course immediately to remove salt and salt water around the tub in order to prevent corrosion.

• Remove lower rack and unscrew the cap of salt container.

• Before using your dishwasher for the first time, it is necessary

to Pour 1.5kg of salt and 1 litre of water in to the container. Otherwise salt refill lamp always turn on during operation.

Use a funnel for ease and clean filling, ensuring that coarse salt or regenerating salt intended for dishwashers is used.

• After filling, wipe off any spilled salt to seal the cap properly.

• Screw the cap tightly to prevent any suds from penetrating into

the container.

In order to provide satisfactory rinsing results, the dishwasher requires soft water, i.e., containing little or no lime, otherwise water stains will be left behind on the dishes and interior containers. If the tap water exceeds a certain level of hardness, it must be softened, I.e.,decalcified. This is achieved by adding a special salt to the water softener inside the dishwasher. The required amount of salt is set up according to how hard your tap water is.

This model has a water softener to soften hard water. Please read these notes carefully for correct operation.

■ 

Filling with Salt

To fill the Rinse Aid chamber, push the rinse aid button. Fill the container to the maximum level with a good quality Rinse Aid, then close the cap. The Rinse Aid is automatically dispensed during the final rinse cycle.

The dosage is factory set to suit most installations. If, after washing, you notice cloudy spots, streaks or water marks on your glassware, it may be necessary to increase the setting. To do this, remove the cap and rotate the indicator arrow to a higher setting then replace the cap . If the glass is smeared or foam is present on the bottom of the glass or the bottom of the machine, select a lower setting.

BEFORE USING FOR THE FIRST TIME

1. MFL66281485_EN_131210.indd 16 2013.12.10 8:58:22 AM

Programme

Time in minutes

Water in

Liter

Energy in

KWh

Eco 170 10 0.92

■ Appliance loaded in accordance with

standard specifications.

• Capacity : 14 place settings

• Standard course : Eco

• Rinse Aid setting : 4

• Reference cleaner : 35g of detergent onto the

inside surface of the door.

• Height-adjustable Rack-U must be inserted

into the uppermost position.

• It is the most efficient programme in terms

of its combined energy and water consumption for that type of tableware.

2. Upper Rack

1. Cutlery Basket

3. Lower Rack

Milk

Egg

Margarine

Te a

Oat

Meat

Spinach

d g

c f

Milk

Egg

Margarine

Te a

Oat

Meat

Spinach

INFORMATION FOR ENERGY TEST(EN50242)

1. MFL66281485_EN_131210.indd 17 2013.12.10 8:58:24 AM

Daily use load

1. Cutlery Basket

2. Upper Rack

3. Lower Rack

HOW TO USE AND OPERATE

Do not use the pot and pan with plastic handle.

• Poor washing for smudges of waterproof or long lasting lipsticks on the glass.

•

CAUTION

1. MFL66281485_EN_131210.indd 18 2013.12.10 8:58:24 AM

NOTE

Non Dishwasher Safe Items

The combination of high water

temperatures and dishwasher detergent may damage particular items, therefore we do not recommend using the dishwasher to wash the following:

Copper or anodised aluminium Hand painted silver or gold leaf crockery Wood or bone handled utensils Iron or non rust proof utensils Plastic items which are not dishwasher

safe

Expensive one such as silvers and

dishes with golden rings

Fragile item such as crystal glasses

For better washing performance, always load the dishwasher according to the instructions.

■ Before loading items into the dishwasher.

• Clean off large particles of food, in

particular insoluble items such as bones, pips etc.

• Items with burnt on food should be soaked

prior to loading in the dishwasher.

■ While you load items into the dishwasher.

• Load all items with the opening down. (Make sure that water does not collect in a deep base.)

• Deep based items should be placed at an

angle to help water run off and dry properly.

• Make sure that all items do not touch each

other.

■ Take care not to obstruct the rotation of

spray arms.

■ Plastic items do not dry as well as steel or

porcelain items.

HOW TO USE AND OPERATE

1. Cutlery Basket

Place forks and spoons in the cutlery basket with their handles downwards.

For Large utensils, such as whisks, the cover can be opened by being unhinged. Take care not to obstruct the rotation of the spray arm.

Slide two baskets in opposite directions, then pull them apart.

①

②

①

②

The basket can be split along its length, increasing the lower rack’s loading versatility.

The cutlery shouldn’t be longer than 18cm.

Max

18cm

To prevent injuries, • place knives and

other utensils with sharp points on the cutlery rack.

If you want to load them in the cutlery

• basket, place them with the pointed edges

facing downwards.

WARNING

1. MFL66281485_EN_131210.indd 19 2013.12.10 8:58:26 AM

Plates should be positioned upright and facing the centre of the rack and pots, pans and large dishes must be turned upside down.

2. Lower Rack

The lower rack is suitable for dinner plates, soup bowls, dishes, pots, pans, lids and even the grill tray.

HOW TO USE AND OPERATE

Take care not to obstruct the rotation of the spray arms.

Plates should be positioned upwards with the plate bottom facing the front of the rack. Cups, glasses and bowls must be positioned upside down.

3. Upper Rack

The upper rack is suitable for delicate items such as, small plates, long cutlery, cups, glasses and dishwasher safe plastic items.

How to fold down

Take care not to obstruct the rotation of the spray arm under the upper rack.

The knife rack provides support for long stem glasses.

The cup racks can be folded up out of the way for tall crockery items.

Ex) Loading large pot

Fold up state

Fold down state

1. MFL66281485_EN_131210.indd 20 2013.12.10 8:58:28 AM

+ 44 hidden pages

LG D1451LF Owner’s Manual

Specifications and Main Features

Frequently Asked Questions

User Manual